WORKSURFACE ASSEMBLY

Transcription

1 WORKSURFACE ASSEMBLY Notes: Worksurfaces should be installed last. This provides easy access to Core/Walls. For Double Sided configurations, repeat the following sequences for the opposite side of the unit. To assemble Worksurfaces to Profile (linear configurations): Reference figures 63 & 64. Attach a Mid Support Bracket to the Core/Wall with two #10-24 x 1/2 phillips flat head thread forming screws as shown in figure 63a. See figure 63a Core Figure 63 Mid Support Bracket (2) #10-24 x 1/2 Phillips flat head thread forming screws Figure 63a 61

2 WORKSURFACE ASSEMBLY Cont. Worksurfaces: Position the Worksurface on the Uprights as shown in figure 64. Align the pilot holes in the bottom of the Worksurface with the holes in the Uprights and secure using the #10-32 x 3/4 phillips head wood screws provided. Note: When linking two Worksurfaces together, a Tie Plate must be used. Secure using the #10-32 x 3/4 phillips head wood screws provided. Worksurface Tie Plate (use with adjoining worksurfaces) #10-32 x 3/4 Phillips Head wood screws Upright Figure 64 62

3 WEDGE TOP ASSEMBLY (convex) Cont. Note: Installation of worksurfaces should start by installing the center Wedge Top first and then out to the ends for proper/ease of alignment. To assemble Worksurfaces to Profile: Wedge Top: Reference figures 65 & 66. Attach a Mid Support Bracket to the Core/Wall with two #10-24 x 1/2 phillips flat head thread forming screws as shown in figure 65a. See figure 65a Figure 65 Mid Support Bracket (2) #10-24 x 1/2 Phillips flat head thread forming screws Figure 65a 63

4 WEDGE TOP ASSEMBLY (convex) Cont. Position the Wedge Top as shown in figure 66a. Align the pilot holes in the bottom rear of the Wedge Top with the holes in the Mid Support Bracket and secure using the #10-32 x 3/4 phillips head wood screws provided. Link the Worksurfaces to the Wedge Top with two Tie Plates using the #10-32 x 3/4 phillips head wood screws provided. Reference figure 66a. See figure 66a Figure 66 Wedge Top Mid Support Bracket Worksurface Worksurface Tie Plate Tie Plate #10-24 x 1/2 Phillips flat head thread forming screws Figure 66a 64

5 TRIM/PANELS ASSEMBLY Cont. Note: The Core/Wall Skins are designed to be removable for easy access to the Core/Wall interior. To attach Core/Wall Skins: Reference figure 67. Install the Core Skins and Wall Skins by engaging the hooks at the bottom of the skins with the slots in the base of the Core/Walls and FPD Walls. Rotate the skins up to snap the clips into the catches. Reference figure 67. Latches FPD Wall Wall Skin Core Skin Core Hook Figure 67 65

6 TRIM/PANELS ASSEMBLY Note: For Double Sided configurations, the following sequence is the same for both right hand and left hand screens. To assemble Privacy Screen(s) to Profile units: Reference figures 68, 69, 70 & 71. Position a Privacy Screen as shown in figure 68 and fasten it to the Core and FPD Wall using two 1/4-20 x 1/2 hex washer head screws. FPD wall Privacy Screen (right hand shown) Core (2) 1/4-20 x 1/2 Hex washer head screws Figure 68 (2) 1/4-20 x 1/2 Hex washer head screws Figure 68a (Double Sided) 66

7 TRIM/PANELS ASSEMBLY Cont. Note: For Double Sided configurations, refer to figure 69a. Position a Filler Panel as shown in figure 69. Align the holes in the Filler Panel with the oval shaped holes in the Core and FPD Wall and fasten using four 1/4-20 x 1/2 hex washer head screws. Repeat this process to install a Privacy Screen and Filler Panel to the opposite end of the unit, if necessary. Reference figure 69a. (4) 1/4-20 x 1/2 Hex washer head screws Filler Panel Figure 69a (Double Sided) Filler Panel FPD wall (4) 1/4-20 x 1/2 Hex washer head screws Core Figure 69 67

8 TRIM/PANELS ASSEMBLY Cont. Note: For Double Sided configurations, refer to figure 70a. Assemble the Top Cap Trim to the top of the Privacy Screen and Filler panel using two #10 x 1/2 phillips flat head screws. Reference figure 70. Repeat this process for the opposite end of the unit if necessary. (2) #10 x 1/2 phillips Flat head screws Top Cap trim (2) #10 x 1/2 phillips Flat head screws Figure 70a (Double Sided) Top Cap trim Privacy Screen Filler Panel Figure 70 68

9 TRIM/PANELS ASSEMBLY Cont. Note: It is important to secure Privacy Screens to Uprights to prevent damage to Screen. Secure the front of the Privacy Screen to an Upright. First remove the knock-out located on the inside of the Upright. Insert a #10-32 x 3/4 phillips pan head wood screw thru the hole in the Upright and into the mating hole in the Privacy Screen. Reference figure 71a. Repeat this process for the opposite end of the unit if necessary. See figure 71a Figure 71 Worksurfaces not shown For clarity #10-32 x 3/4 Phillips pan head wood screw Privacy Screen Remove knock-out Upright Figure 71a 69

10 TRIM/PANELS ASSEMBLY Cont. To attach Vertical End and Transitional Wall Trim to Profile: Reference figures 72 & 73. Attach the Vertical Trim to the end of the unit by inserting the studs on the Vertical Trim into the holes in the Core/Wall and PDF Wall. Secure with two 1/4-20 hex kep nuts. Reference figure 72. Vertical Trim Stud (2) 1/4-20 Hex kep nuts Figure 72 70

11 TRIM/PANELS ASSEMBLY Cont. For Transitional Wall Trim: Insert studs in Transition Wall Trim with holes in FPD Wall. Magnetic strips on Wall Transition Trim will secure it to the FPD Wall. Reference figure 73 & 73a. Magnetic strips this side Holes Transition Wall Trim FPD Wall See figure 73a Figure 73a Figure 73 71

12 TRIM/PANELS ASSEMBLY Cont. Note: The Top Trim is designed to be removable for easy access to the Core/Wall interior. To install the Top Trim: Reference figure 74. Install Grabber Latches to both ends of the FPD Wall (Note orientation of latches when installing). Reference figure 74. Align the Top Trim with the top of the unit as shown and engage Grabber Latches. Top Trim Grabber Latch Align with back of single side. (Alignment not necessary with Double side unit.) Figure 74 72

13 TRIM/PANELS ASSEMBLY Cont. Note: The Cable Access Panels are designed to be removable for easy access to the Core/Wall interior. To install the Cable Access Panels: Reference figures 75 & 75a. Install the Cable Access Panels by engaging the top flange of the panel under the Slatwall and rotating down, inserting the clips into the catches. Reference figure 75 and 75a. See figure 32a Top flange Figure 75 Slatwall Access Panel Catch Figure 75a 73

14 DESKTOP MODULAR RACKMOUNT 24 & 36 To assemble the 24 Desktop Modular Rackmount: (reference figures 76, 77, 78, 78 & 79) Install two End Filler Panels to the back of the Desktop Modular Rackmount Unit using four #8AB x 1/2 phillips pan head screws. Reference figure 76. Position the rackmount unit against the 48 FPD wall. Reference figures 77 & 79. Slide two Mounting Brackets into the two slots on the back of the unit. Reference figures 78 and 78 a. 24 Desktop modular rackmount unit 48 Profile unit 16 H Modular wall Filler panels 24 Desktop modular rackmount unit (4) #8AB x 1/2 phillips pan head screws Figure 76 Figure 77 See figure 78a Slots Slot Mounting brackets Mounting bracket Figure 78 Figure 78a 74

15 DESKTOP MODULAR RACKMOUNT 24 & 36 Cont. Align the the holes in Mounting Brackets with the holes on the top of the 16 H modular wall and secure using two #10-24 x 3/8 phillips pan head screws. Reference figures 79 & 79a. Secure the Filler Panels to the inside of the FPD wall using two #10-24 x 3/8 phillips pan head screws. Reference figure 79b. See figure 79a 16 H Modular wall See figure 79b #10-24 x 3/8 phillips pan head screw Figure 79 #10-24 x 3/8 phillips pan head screw Filler panel Mounting bracket Figure 79a Figure 79b 75

16 DESKTOP MODULAR RACKMOUNT 24 & 36 Cont. To assemble the 36 Desktop Modular Rackmount: (reference figures 80, 81, 82, 83, 84, 85 & 86) Install a Filler Panel to the back of the Desktop Modular Rackmount Unit using two #8AB x 1/2 phillips pan head screws. Reference figure 80. Install a Support Bracket to the back of the unit using two #8AB x 1/2 phillips pan head screws. Reference figure 80. Position the rackmount unit against the 16 high modular wall. (Note: Remove Vertical Divider before installing unit. Reference figure 81. Slide two Mounting Brackets into the two slots on the back of the unit. Reference figures 82 & 82a. 36 Desktop modular rackmount unit 36 Profile unit 16 H Modular wall Support bracket 24 Desktop modular rackmount unit Filler panel (4) #8AB x 1/2 phillips pan head screws See figure 82a Figure 80 Slots Figure 81 Slot Mounting brackets Mounting bracket Figure 82 Figure 82a 76

17 DESKTOP MODULAR RACKMOUNT 24 & 36 Cont. Align the the holes in Mounting Brackets with the holes on the top of the 16 high modular wall and secure using two #10-24 x 3/8 phillips pan head screws. Reference figures 83 & 83a. Secure the Filler Panel to the inside of the 16 high modular wall using one #10-24 x 3/8 phillips pan head screw. Reference figure 83b. See figure 83a 16 H Modular wall See figure 83a Figure 83 #10-24 x 3/8 phillips pan head screw Filler panel #10-24 x 3/8 phillips pan head screw Mounting bracket Figure 83a Figure 83b 77

18 DESKTOP MODULAR RACKMOUNT 24 & 36 Cont. Install four door latches in the appropriate square holes in the 16 H modular wall. Reference figure 84. Install four door strikes in the square holes in the Full Height Panel. Reference figure H Modular wall Square hole on wall Door latch Figure 84 Square hole in panel stiffener Full height panel Door strike Figure 85 78

19 DESKTOP MODULAR RACKMOUNT 24 & 36 Cont. Install the Full Height Panel by snapping the strikes into the latches. Reference figure 86. Full height panel Door strike Door catch Figure 86 rear view 79

20 MONITOR ARMS AND ACCESSORIES Note: Exhaust fans can be installed in multiple locations within wall(s); typically within the uppermost wall. They can also be installed within multiple tiers. To install exhaust fans into uppermost tier walls: Reference figures 87 & 87a. Install an Exhaust Fan to the top of the FPD Wall using two #10-32 x 3/8 phillips pan head thread forming screws as shown in figure 87a. #10-32 x 3/8 Phillips Pan head thread forming screws Exhaust Fan See figure 34a FPD Wall Figure 87a Figure 87 80

21 MONITOR ARMS AND ACCESSORIES Cont. To install an exhaust fan to a mid-tier Wall : Reference figures 88 & 88a. Install an Exhaust Fan to the top of the FPD Wall using two #10-32 x 3/8 phillips pan head thread forming screws as shown in figure 88a. Slide under wall end surface And secure with screws as shown FPD Wall Exhaust Fan See figure 88a FPD Wall #10-32 x 3/8 Phillips Pan head thread forming screws Figure 88a Figure 88 81

22 MONITOR ARMS AND ACCESSORIES Cont. To install Power Accessories : Reference figure 89 & 90. Remove Tie Plates to gain un-obstructed access to the Core/FPD Wall Raceways. Set aside and replace after Power Accessories are in place. Note: It is very important to replace the Tie Plates to maintain Slat Wall and Monitor Arm stability. Install Power accessories into built-in raceways within the Core(s) and FPD Wall(s). Note: Side-by-side and center installation configuration options in figure 90. See figure 89a Tie Plates Power Accessory Core/FPD Walls Figure 89 Figure 89a Side-by-side Centered Figure 90 82

23 MONITOR ARMS & ACCESSORIES The following pages show how to attach the Flat Panel Display Arms to the Slat Walls. Flat Panel Display Arm 83