2011 Cadillac CTS Coupe
|
|
- Lydia Weaver
- 5 years ago
- Views:
Transcription
1 IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! Copyright 2010 by E&G Classics, Inc. All right reserved. The reproduction or uti li za tion of this work in any form or any elec tron ic, me chan i cal, or other means, no known or here af ter in vent ed, including xe rog ra phy, pho to copy ing, and re cord ing, and in any in for ma tion storage retrieval system is for bid den with out written per mis sion of owners Cadillac CTS Coupe Rear Tag Surround Part #: Complete TOOLS REQUIRED Electric Drill, 1/8 drill bit, rivet gun, automotive grade masking tape, automotive grade sealer/rust preventer. K 03 HO P Notes to the Technician/Installer: E&G is proud to present this package to you and reminds you that for technical in for ma tion, contact technical assistance at Do not at tempt the in stal la tion of any E&G prod uct without first reading the detailed in struc tions. E&G Clas sics will not war rant dam aged parts or the ve hi cle due to altered in stal la tion in struc tions Highlight the body line where the tag recess area begins with a grease pencil. 2. Measure over 5/16 towards the sides of the trunk and mark with a grease pencil. 3. Apply masking tape to cover the grease pencil marks made in Step Remove the grease pencil marks made in Step Make sure that the top of the taped line extends at least 1/16 be yond the factory chrome moulding. 6. Trim the supplied 3M clear protection tape at the same angle as the intersection of the factory moulding and the tag recess opening.
2 With the top of the 3M clear protective tape aligned in place, trim the bottom of the tape at the same angle as the bottom of the trunk lid. Cut the tape 1/2 past the edge of the trunk lid. 8. Carefully align the 3M clear protective tape against the edge of the masking tape and smooth it down onto the painted trunk lid. Once the tape is in place, fold the long edge up underneath the trunk lid Align the 22 gage stainless steel filler into place and once it is perfectly centered, mark the bottom edges of the filler with a grease pencil. These marks will assist in the left and right upright alignment Align the left and right uprights into place, flush with the factory moulding at the top and just covering the grease pencil marks made at the bottom in the previous step. 11. Use a grease pencil or marker to mark the mounting hole locations on the uprights, then remove the uprights Once the uprights have been removed, use a 1/8 drill bit to drill through the first layer of metal only. IMPORTANT: Do not drill through the holes in the uprights as the drill bit or chuck will damage the chrome plated uprights causing rust problems that E&G will not cover by the warranty. 13. Use a high quality sealer to prevent future rust problems.
3 Using a rivet gun, install the supplied s.s flat washers (early production uprights) and 1/8 rivets to secure the uprights to the trunk lid. 15. Once the uprights are installed, peel off the foam tape applied to the tag recess from the factory Align the 22 ga. s.s. filler and mark the opening locations onto the tag recess using a grease pencil. 17. Using the supplied template, cut out the supplied 4 black pressure tape into left and right black out tape sections. 18. Apply them over the grease pencil marks made in the previous step, making sure you remove any air bubbles trapped under the tape Peel off all of the double faced tape backing from the 22 Ga. s.s. filler. 20. Align the mesh sections and use the.015 x 1 double faced tape at the tops of the openings the hold the mesh in place during the filler alignment. 21. Make sure that the 22 Ga. filler is tight against the factory chrome mounlding, then rotate the filler down into place and press firmly enough to set the tape. The bottom of the filler should be flush or slighly above the lower edge of the trunk lid.
4 Part # Quantity: Description: Part Number: 1 Right Upright Left Upright Ga. Polished S.S. Filler Fine Mesh Sections Installation Hardware Kit M Scotchcal Protection Film Black Pressure Tape Once the filler is attached to the trunk lid, remove the protective backing from the fille and use a mild solvent and a clean, soft cloth to remove any glue residue. Follow with glass clean or alcohol and a soft clean rag to remove any solvent residue. 23. Finished installation. 4 SSD44SSBS Rivets Stainless Steel Flat Washers R 1 Black Out Tape Template E&G Classics Warranty Information: E&G Classics, Inc. warrants its chrome parts and products to be free from defects in ma te ri al, workmanship or finish for Thirty-Six (36) months from the date of shipment by E&G. This warranty is limited to the repair or replacement, at E&G Classics option, of the defective part or product.full E&G Classics warranty information is available Just click on the product warranty icon. For E&G Classic Product Returns: Please contact the authorized E&G Classics Dealer where you purchased our product from in regards to any workmanship or warranty claims. All items returned to E&G Classics must have a return authorization number issued by us for inspection or a defective product and or warranty issue. All merchandise sent back to E&G Classics without proper paperwork or authorization will be rejected and returned.
5
Q Grille Part # Q WARNING: STEEL MESH & GRILLE CAN BE EXTREMELY SHARP!
Mesh Grille Part #1341-0102-08 Notes to the Technician: E&G is proud to present this package to you and reminds you that for technical in - for ma tion, contact Lynn Eash or Lee Clary at 410-381-4900.
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 2007-09 Dodge Nitro Upper and Lower Stainless Steel Mesh Grille J 07 G8R Notes to the Technician: E&G is proud to present this package
More information2011 KIA Optima SX / EX Turbo Mesh Grille
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED 2011 KIA Optima SX / EX Turbo Mesh Grille Upper and Lower Overlay Part #: Complete 1310-0102-11SX / Black Ice Part #1310-B102-11SX
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE Quantity Description Part No. 1 Set ABS Front Air Dam Right 5409-1401-10U Center 5409-1402-10U Left 5409-1403-10U Right End Cap 5409-1405-10
More informationIMPORTANT: WILL NOT FIT COUNTRYMAN MODELS
Part #1410-0102-07 2 3 1 IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS Apply masking tape around the bottom grille opening and across the bottom of the upper facto ry grille.. Open the hood and remove the
More informationSimply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware.
2 Simply lift up on the flexible cover to remove it from the radiator support panel and factory grille, exposing the upper mounting hardware. Apply masking tape to the top of the bumper cover underneath
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 005-07 Cadillac STS Classic 3D Z, Classic Dual Weave, Classic Mesh & Classic Black Mesh Grilles B 7 HR 3 STS Classic 3D Z Grille Part
More information4" Oval Nerf Bar. Part No. A1007S/B. PARTS LIST: Qty Part Description Qty Part Description
4" Oval Nerf Bar Part No. A1007S/B Fits: 2009 - Current Dodge Ram 1500 Crew Cab 2001 - Current Dodge Ram 2500/3500 Crew Cab REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not
More information3-PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS. 407L Toyota Hilux 2005 Onwards
3-PC TONNEAU COVER WITH SPORTS BAR INSTALLATION INSTRUCTIONS TC004c /7 407L Toyota Hilux 005 Onwards Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More informationInstallation Instructions:
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. (SB76904) Parts Included Qty 94-241CA001 Front Upright: Drvr 1 94-241CA002 Front Upright: Pass 1 94-241CA003
More informationFENDER FLARE. KIT CONTAINS Qty Part Description Qty Part Description
` FENDER FLARE Part No: FFC3002S TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF THE FENDER FLARE CAREFULLY. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting Not Required
More informationFENDER FLARE INSTALLATION
Customer Support TM FENDER FLARE INSTALLATION TG-FF8C4108 IMPORTANT TYGER only approves the installation according to our instructions with the hardware provided. WARNING Failure to complete the installation
More informationIncluded in Hardware Kit 4. Jeep Wrangler JK 4-Door Rear Flares. Set Part # Rev STEP 1 PRIOR TO INSTALLATION
A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to
More informationRev TOOLS & MATERIALS REQUIRED QTY 3D PART NO. DESCRIPTION
Rev. 04-11 QTY 3D PART NO. DESCRIPTION 1 691800 FRONT AIR DAM 1 691802 RIGHT SIDE SKIRT 1 691801 LEFT SIDE SKIRT 1 691804 REAR LOWER SKIRT RIGHT SIDE 1 691803 REAR LOWER SKIRT LEFT SIDE 4 3M 94 3M ADHESION
More informationJeep. Flat Style Fender Flares Front Pair. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationFlat Style Fender Flares Rear Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,
More informationIMPACT DOOR 3000 SERIES. This Manual Covers All Doors Shipped To Date, Except For Revised Jamb Guards.
IMPACT DOOR 3000 SERIES This Manual Covers All Doors Shipped To Date, Except For Revised Guards. PRINTED IN U.S.A. PUBLICATION NO. 3400C EMAIL: PRINTSHOP@RITEHITE.COM JANUARY 2010 INTRODUCTION TABLE OF
More informationJeep Wrangler JK Door Rear Pair Part # Revision E
Jeep Wrangler JK 2007 4-Door Rear Pair Part # 10044 Revision E 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the
More informationDEVONSHIRE ELOSIS ORDERING INFORMATION PARTS INSTALLATION INSTRUCTIONS MIRROR CABINET. , 2005 Copyright Kohler China Ltd.
DEVONSHIRE ELOSIS INSTALLATION INSTRUCTIONS MIRROR CABINET BEFORE YOU BEGIN Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences.
More informationJeep. Flat Style Fender Flares Rear Pair. Included in Hardware Kit:
Jeep Flat Style Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationNISSAN T30 X-TRAIL WITH SUNROOF CARGO BARRIER FITTING INSTRUCTION PART NO YEARS OF MANUFACTURE MAY 2002 ONWARDS.
NISSAN T30 X-TRAIL WITH SUNROOF CARGO BARRIER FITTING INSTRUCTION PART NO 405500 YEARS OF MANUFACTURE MAY 2002 ONWARDS. Page 1 of 6 This Cargo Barrier is a single position barrier located behind the 2nd
More informationALLORA SWING PANEL INSTALLATION INSTRUCTIONS
ALLORA SWING PANEL INSTALLATION INSTRUCTIONS Before Installation Please check that your Allora Swing Panel is undamaged SEQUENCE OF INSTALLATION These instructions are also available from the Athena website:
More informationIncluded in Hardware Kit: Jeep. Pocket Style Extended Coverage Fender Flares Rear Pair
A) B) C) D) E) F) G) H) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according
More informationChevrolet Pocket Style Fender Flares Set of 4
Chevrolet Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:
More information340 & 350 SERIES BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340 & 350 SERIES BATH ENCLOSURES 800-643-1514 www.alumaxbath.com Copyright Alumax Bath Enclosures 2010. All rights reserved. LIMITED WARRANTY AND REMEDY ALUMAX BATH ENCLOSURES
More informationINSTALLATION INSTRUCTIONS / DODGE RAM CREW CAB 2500/3500
INSTALLATION INSTRUCTIONS 225019 / 225019-2 2010 DODGE RAM CREW CAB 2500/3500 PARTS LIST: Qty Description Qty Description 1 Driver/Left Side Bar 4 Plastic Square Retainer 1 Side Bar 2 12mm x 120mm Hex
More information340 & 350 SERIES DELUXE FRAMELESS BYPASS
BATH ENCLOSURES An Alcoa Company Tel: 800-643-1514 Fax: 870-234-3181 www.alumaxbath.com INSTALLATION INSTRUCTIONS 340 & 350 SERIES DELUXE FRAMELESS BYPASS BATH ENCLOSURES Copyright Alumax Bath Enclosures
More informationASSEMBLY INSTRUCTIONS FOR HAULER II SERVICE BODY A RACK
ASSEMBLY INSTRUCTIONS FOR HAULER II SERVICE BODY A RACK T12USBA-1 shown above Package Contents: HARDWARE KIT PARTS (4) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLY (20) 3/8-16 x 2 CARRAIGE
More informationINSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ
INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting
More informationIncluded in Hardware Kit: 1. Jeep. Pocket Style Factory Coverage Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: REAR SPOILER KIT - CARBON FIBER INFINITI Q60 T99J1 5CH0B KIT CONTENTS: Item Qty. Part Description A 1 Spoiler Assembly B 4
More informationAllora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED
Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED ALCOVE SHOWER Your shower can be installed to open Left hand or Right hand by rotating
More informationBolt-On/Rugged Fender Flares GMC Sierra 1500/2500/3500 (14-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included Extrusion 30.5ft (Bolt-On look flare only) QTY U CLIP.6mm 6 Nuts
More informationHAINSWORTH WRITING DESK ASSEMBLY INSTRUCTIONS
Item# BP-HSWD52-W8 HAINSWORTH WRITING DESK ASSEMBLY INSTRUCTIONS IF PARTS ARE MISSING OR DAMAGED, DO NOT RETURN TO STORE To order missing or replacement parts, contact us via e-mail parts@officestar.net,
More informationJeep Wrangler JK & 4-Door Front Pair Part # Revision H
Jeep Wrangler JK 2007 2 & 4-Door Front Pair Part # 10045 Revision H 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with
More information(2) 25mm x 20mm x 5mm Adhesive Backed Foam Pads. 100mm x 50mm x 1.0mm Adhesive Backed Foam. (2) Spacer Plates. Passenger/Right Side Frame Mounting
PARTS LIST: 1 Grille Guard 10 12mm Lock Washers 1 Driver/Left Frame Mounting 16 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Frame Mounting 8 12mm Hex Nuts 1 Driver/Left Side Top Support 2 10-1.50mm
More information8mm x 25mm "Z" Bolt Plates. (2) Tube Spacers. (2) 12mm Bolt Plates w/ Nut
PARTS LIST: 1 Grille Guard 10 12mm Lock Washers 1 Driver/Left Side Frame Mounting Bracket 8 12mm Hex Nuts 1 Passenger/Right Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Driver/Left
More informationASSEMBLY INSTRUCTIONS FOR SERVICE BODY A MOUNT RACKS
ASSEMBLY INSTRUCTIONS FOR SERVICE BODY A MOUNT RACKS T12 Service Body A shown with optional middle crossbar Package Contents: HARDWARE KIT PARTS (8) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLIES
More information12. Wings, Flaps, Ailerons and Struts
12. Wings, Flaps, Ailerons and Struts Fit Aileron Hinges Reference: Drawing 20270K2 Photo 12.1 Parts Required: 2007092 Aileron LS 200809N Aileron RS 2001394 Hinge 3/16 A1 (4) 2001694 Hinge Pin (4) PH0059N
More information1PC TONNEAU COVER INSTALLATION INSTRUCTIONS. Holden VE Ute 2007
PC TONNEAU COVER INSTALLATION INSTRUCTIONS Holden VE Ute 007 Part Number: EGR-PVE-UNP Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents.
More informationINSTRUCTION BOOK FOR. IDEA Screen & Panoramic for Nureva Span
INSTRUCTION BOOK FOR IDEA Screen & Panoramic for Nureva Span Disclaimer Milestone and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete.
More informationChevrolet Pocket Style Fender Flares Set of 4
Chevrolet Pocket Style Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PROTRAXX OVAL STEP BAR APPLICATION: 2009-2017 Dodge Ram 1500 Crew/Quad Cab 2010-2017 Dodge Ram 2500/500 Crew Cab PART NUMBER: 21-550, 21-555, 21-50, 21-55 AUTOMOTIVE PRODUCTS,
More informationSCION FR-S REAR SPOILER Preparation
Preparation Part Number: PT938-18130-XX Kit Contents Item # Quantity Reqd. Description 1 1 Spoiler 2 2 Strut 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 M6 x 1 Nut with
More informationA-LOOK ver 1 A-LOOK TM. Installation Manual
A-LOOK ver 1 A-LOOK TM Installation Manual Tools Required Pencil Measuring Tape Drill Hack Saw with 12D/32T Blade Jigsaw Self-Centering Punch Framing Square 7/16" Wrench Ladder 2" or 3" Paint Brush for
More informationInstallation Instructions
Installation Instructions Sure Step (Part # DN260-S4B/ DN260-S4S Part # DN270-S4B/ DN270-S4S) 2009-2010 Dodge Ram1500 Crew Cab & Quad Cab 2010 Ram 2500/3500 Crew Cab For Technical Support/Warranty Information
More informationGRILLE GUARD SPRINTER VAN (EXCLUDES X4) INCLUDES MERCEDES, FREIGHTLINER AND DODGE PARTS LIST:
PARTS LIST: 1 Grille Guard 8 12mm Hex Nuts 1 Driver/Left Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Passenger/Right Side Frame Mounting Bracket 4 10mm x 20mm OD x 2mm Flat Washers
More informationInstallation Instructions/Operation and Maintenance Manual. PS DOORS Contact Information. Website psdoors.com
Ladder Safety Gate Installation Instructions/Operation and Maintenance Manual Models All Models: LSG-5 to LSG-48 Table of Contents Product Information...2 Inspection & Mainteance...2 Warranty Information...2
More informationASSEMBLY INSTRUCTIONS ABST-101-BK SPEAKER STAND ACST-101-BK CENTER CHANNEL STAND
ABST-101-BK SPEAKER STAND ACST-101-BK CENTER CHANNEL STAND ASSEMBLY INSTRUCTIONS Safety Instructions 1. General information Please read and follow these safety instructions. Keep them safe for future reference.
More informationIncluded in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ. Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Wrangler YJ Set Part #10924-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware
More informationSet Part # Rev
Set Part # 21007 Rev-3 06-06-11 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with the hardware provided. WARNING: Failure to
More informationINSTALLATION INSTRUCTIONS 3 BULL BAR 99-04, 04 "HERITAGE" F-150/250LD 2WD, 97-04, 04 "HERITAGE" 4WD WD EXPEDITION/ WD EXPEDITION PART
INSTALLATION INSTRUCTIONS 3 BULL BAR PART #B-F1971;B-F2971 PARTS LIST: 1 Bull Bar 2 12-1.75mm x 130mm x 40mm Hex Bolts 1 Driver/Left Mounting Bracket 4 12-1.75mm x 35mm Hex Bolts 1 Passenger/Right Mounting
More informationToyota Extend-A-Fender Fender Flares Set of 4
Toyota Extend-A-Fender Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING:
More information300C6 CONTINUOUS HINGE SEMI-FRAMELESS DOOR KIT
300C6 CONTINUOUS HINGE SEMI-FRAMELESS DOOR KIT LIMITED WARRANTY AND REMEDY Alumax Bath Enclosures warrants to its dealers, customers, and all subsequent purchasers and users, that the products supplied
More informationDual Arm Tilt LCD Mount
Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,
More informationIncluded in Hardware Kit: Pocket Style Extended Coverage Fender Flares Rear Pair. Jeep
Jeep Pocket Style Extended Coverage Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided.
More informationUser Guide.
User Guide www.dymo.com D I K M L H G C F A B E J N A Tape cassette door H Character selection window B Tape rollers I Cutting handle C Tape advance knob J Embossing adjustment screw D Start line K Cable
More informationBath Accessory Installation
Bath Accessory Installation Step 1 - Clean surface using a clean dry cloth or use rubbing alcohol to remove any residue (wax, grease, solvents). Allow to dry one hour. Caution! DO NOT use any household
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationINSTALLATION INSTRUCTIONS
SG57f GENUINE PARTS INSTALLATION INSTRUCTIONS. DESCRIPTION: Sunroof Wind Deflector. APPLICATION: Pathfinder; Frontier with no roof rails 3. PART NUMBER: 999D4-XR00 4. KIT CONTENTS: Item No. ) ) 3) 4) 5)
More informationBolt-On Fender Flares Nissan Titan XD (16-ON) Important: Please read instructions entirely before installing this product.
Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included Extrusion 30.5ft (Bolt-On look flare only) QTY U CLIP.6mm 6 Nuts
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET
More informationFlat Style Fender Flares Front Pair. Jeep. Included in Hardware Kit:
Jeep Flat Style Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationGENERAL INSTALLATION GUIDE: WARRANTY: PRODUCT INFORMATION T F
GENERAL INSTALLATION GUIDE: Unless otherwise indicated, all Seven Oaks M.U. Architectural Products materials are to be used for decorative purposes only. All products must be installed using ample amount
More informationWEAR SAFETY GLASSES WHEN INSTALLING THIS KIT.
INSTALLATION INSTRUCTIONS Trans4mer Mounting Systems Part No. 29753 (black) Part No. 65654 (stainless) for full size GM pickups, and Blazer, Yukon, Suburban, Tahoe As you read these instructions, you will
More informationAccess Hatch. Installation Instructions and Operators Manual. PS DOORS Contact Information. Model AH-710 Standard High Neck Radius Cut
Access Hatch Installation Instructions and Operators Manual Standard Low Profile Frame Model AH-710 Standard High Neck Radius Cut High Neck Frame for special applications. Table of Contents Warranty Information...2
More informationInstalling A Carver Bimini Top
Installing A Carver Bimini Top How To Prolong The Life Of Your Bimini Top Carver Bimini Tops are a classy way to protect yourself and your boat from the elements. They also add style and color to your
More informationStep-by-Step Installation Instructions for
Step-by-Step Installation Instructions for Version 5-06/11 Before Starting: Please read and understand these instructions. Not following these instructions will invalidate your warranty (although this
More informationJeep. Flat Style Fender Flares Set of 4. Included in Hardware Kit: STEP 1 PRIOR TO INSTALLATION. Set Part # Rev-3 1/11/2016
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationIncluded in Hardware Kit. Jeep Cut-Out Fender Flare Set of 4 Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Cut-Out Fender Flare Set of 4 Set Part #10926-07 Rev-01 09-11-12 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the flares according to these written instructions with the hardware
More informationASSEMBLY INSTRUCTIONS FOR HAULER II UNIVERSAL CAMPER SERIES RACKS
ASSEMBLY INSTRUCTIONS FOR HAULER II UNIVERSAL CAMPER SERIES RACKS C11U2873-1 shown above Package Contents: HARDWARE KIT PARTS (4) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLY (20) 3/8-16 x
More informationBefore returning this product to the store of purchase
Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: Missing Parts Installation Problems/Questions Warranty Questions 1.800.779.2102 Hours of
More informationIncluded in Hardware Kit: Pocket Style Extended Coverage Fender Flares Front Pair. Jeep
Jeep Pocket Style Extended Coverage Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided.
More informationCare Instruction: Wash vehicle roof prior to installing Rhino Tracks.
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationIncluded in Hardware Kit: Toyota Tacoma, Regular/Access/Double Cab, Shortbed Set Part # Rev STEP 1 PRIOR TO INSTALLATION
STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure to install according to these instructions
More informationIncluded in Hardware Kit 2. FLAT STYLE FENDER FLARE. Jeep Wrangler YJ Fronts. Set Part # Rev STEP 1 PRIOR TO INSTALLATION
Jeep Wrangler YJ Fronts Set Part #10067-07 Rev-0 05-05-11 A) B) C) D) E) STEP 1 PRIOR TO INSTALLATION Bushwacker only approves installing the fl ares according to these written instructions with the hardware
More information340D & 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES
INSTALLATION INSTRUCTIONS 340D & 350D SERIES FRAMELESS BYPASS BATH ENCLOSURES 800-643-1514 www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2014. All rights reserved. !WARNINGS! INSTALLATION WARNINGS
More informationAdjustable Performance Trim Tab Kit PART# - RS27110-APT
Adjustable Performance Trim Tab Kit PART# - RS27110-APT APPLICATION(S): Sea Doo RXP-X 260 We strongly recommend the use of a service manual to familiarize yourself with the various components and procedures
More informationBlack Moon Products CTS-V Splitter Unfinished [ Cadillac CTS-V Coupe, Sedan & Wagon]
Black Moon Products CTS-V Splitter Unfinished [2009-2015 Cadillac CTS-V Coupe, Sedan & Wagon] The information contained in this manual is updated periodically. While great care is taken in compiling the
More informationApplications: Section 1: Getting Started Tools Needed: BEFORE
Installation of KBD Body Kits Porsche GT 3 Look/Style 2 Piece Polyurethane Front Bumper & Lip Applications: Porsche 996: 1999-2001 Porsche Boxster 986: 1997-2004 Page 1 Tools Needed: Philips Head Screwdriver
More informationFord Cut-Out Fender Flares Rear Pair
Ford Cut-Out Fender Flares Rear Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationAll Terrain Flares 09+ Ford F150
Page 1/5 Components: 1. Front Flares (2) 2. Front Flare Inner Pieces (2) 3. Rear Flares (2) Tools required: - Utility knife - Electric Drill - 1/4 Drill Bit - #2 Phillips driver - Socket wrench Hardware
More informationInstalling 3M DI-NOC Architectural Finishes on Doors
Installation Guide Revision C, September 2017 Introduction The purpose of this installation guide is to establish a 3M-recommended procedure for installing 3M DI-NOC Architectural Finishes (the Product
More informationINSTALLATION INSTRUCTIONS
TEL -866-XANATOS INSTALLATION INSTRUCTIONS PART#: 7D5000SS\7D500A GRILL GUARD FOR DODGE SPRINTER 07-09 PARTS LIST: 8 6 Grille Guard Driver/Left Frame Mounting Passenger/Right Frame Mounting Driver/Left
More informationHURST COMP STICK KIT DODGE CHARGER, MAGNUM, AND CHRYSLER 300 (with AUTO-STICK) Catalog # & by Hurst Performance
HURST COMP STICK KIT 2005-2007 DODGE CHARGER, MAGNUM, AND CHRYSLER 300 (with AUTO-STICK) Catalog #538 0410 & 538 0411 2009 by Hurst Performance FORM 159 0410 03/09 Thank you for purchasing the Hurst Comp
More informationFORD RANGER 1 PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS
FORD RANGER PIECE HARD TONNEAU COVER INSTALLATION INSTRUCTIONS Care Instructions: Clean Tonneau Cover with a mild detergent and water solution. Do not use abrasive cleaners or solvents. Place these instructions
More informationInstallation Instructions:
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included: Qty 93-326EP009 Front Armor: Drvr 1 93-326EP010 Front Fender: Pass 1 90-6774m Hardware Pack:
More informationFord Cut-Out Fender Flares Front Pair
Ford Cut-Out Fender Flares Front Pair STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationChevrolet Cut-Out Fender Flares Set of 4
Chevrolet Cut-Out Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationToyota Cut-Out TM Fender Flares Set of 4
Toyota Cut-Out TM Fender Flares Set of 4 STEP 1 PRIOR TO INSTALLATION A) Bushwacker only approves installing the fl ares according to these written instructions with the hardware provided. WARNING: Failure
More informationSTART HERE BEFORE YOU BEGIN FIG 1 STEP 2
PROFESSIONAL INSTALL RECOMMENDED REAR MODULAR / MULTI LED ROOF MOUNTS PART#: Z350040 / Z350050 REAR ROOF LED LIGHT MOUNTS Parts included (1) - Driver Side Roof Mount Upright (1) - Passenger Side Roof Mount
More informationASSEMBLY INSTRUCTIONS FOR T-10, T-11 & T-12 SERIES RACKS
ASSEMBLY INSTRUCTIONS FOR T-10, T-11 & T-12 SERIES RACKS T12SHD-1 with 26 Legs shown above. Package Contents: HARDWARE KIT PARTS (8) 3/8-16 x 3 CARRAIGE BOLTS (1) RAIL DRIVER S SIDE ASSEMBLIES (20) 3/8-16
More informationREVISION LIST CHAPTER 25: AFT WINDOWS. The following list of revisions will allow you to update the Legacy construction manual chapter listed above.
REVISION LIST CHAPTER 25: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the
More informationPORTROD WALL MOUNTED HEIGHT ROD
PORTROD WALL MOUNTED HEIGHT ROD USER INSTRUCTIONS P/N UMPORTROD Rev 1-052112 1 PORTROD Thank you for your purchase of this Health o meter Professional product. Please read this manual carefully, and keep
More informationFOLIO COUNTERTOP LAVATORY
FOLIO COUNTERTOP LAVATORY 1. BEFORE YOU BEGIN HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences.
More informationHinge Door + One Inline Panel
inge Door + One Inline Panel Instruction Manual KLD + KL Important Information Toughened glass is completely safe for use in our shower enclosures and bath screens; providing our products are installed
More informationINSTALLATION INSTRUCTIONS 6 OVAL BENT END SIDEBARS DODGE RAM 1500, CREW CAB PART#: /241533B
PARTS LIST: 1 Driver/Left Sidebar 24 8mm x 24mm x 2mm Flat Washers 1 Passenger/Right Sidebar 12 8mm Lock Washers 3 Driver/left, Passenger Center and Rear 6 8mm Hex Nuts 3 INSTALLATION INSTRUCTIONS 6 OVAL
More informationFord Ranger / Bronco II Set Part # Rev B 5-04
Ford Ranger / Bronco II Set Part # 21008 Rev B 5-04 Step 1: Prior to Installation: A) Fit: Verify the fit of the flares to vehicle. (Some filing, sanding, or cutting may be necessary to ensure proper fit).
More information