The Wood Products Council is a Registered Provider with. . Credit(s) earned on completion of this program will be

Transcription

1 Connection Solutions for Wood-frame Structures Presented by: John Buddy Showalter, P.E. Vice President, Technology Transfer The Wood Products Council is a Registered Provider with. Credit(s) earned on completion of this program will be reported to AIA/CES for AIA members. Certificates t of Completion for both AIA members and non-aia members are available upon request. This program is registered with AIA/CES for continuing professional education. As such, it does not include content that may be deemed or construed to be an approval or endorsement by the AIA of any material of construction or any method or manner of handling, using, distributing, or dealing in any material or product. Copyright Materials This presentation is protected by US and International Copyright laws. Reproduction, distribution, display and use of the presentation without written permission of the speaker is prohibited. American Wood Council 2012 Questions related to specific materials, methods, and services will be addressed at the conclusion of this presentation.

2 Learning Objectives At the end of this program, participants will be knowledgeable of: 1. Identify basic wood material properties and learn how to avoid splits, notching, and checking in connection solutions. 2. Recommend fastening guidelines for wood-to-steel, wood-to-concrete, and wood-to-wood connections. 3. Describe effects of moisture on wood connections and implement proper flashing to avoid problems. 4. Identify proper fastener selection in size, scope, and pattern.

3 initiators: notches large diameter fasteners hanging loads

4 Full wrap sling option Split Split

5 Split

6 Load high strength, poor ductility good strength, good ductility low strength, good ductility Displacement

7 No end caps or flashing end caps and flashing

8 Saturated 19% MC fabrication MC in-service MC Dowel-type connectors bolts drift pins drift bolts lag screws wood screws nails Dry Moisture trap - No weep holes C M * Lateral load (*C M =0.7 for D<1/4) Withdrawal load - lag & wood screws only Withdrawal load - nails & spikes Saturated C M = 1.0 if: 19% MC 1 fastener fabrication MC in-service i MC Dry C M 0.4 Lateral load (D>1/4) 2+ fasteners split splice plates

9 Slotted hardware

10 Need 1/2 air gap between wood and masonry

11

12

13 Schmidt, R.J. (2006): Timber Pegs Considerations for Mortise and Tenon Joint Design, Structure Magazine, March 2006, NCSEA, 13(3):44-47.

14 Fastener Values Included in U.S. design literature Fastener Type Bolts Lag Screws Wood Screws Nails & Spikes Split Ring Connectors Shear Plate Connectors DiftB Drift Bolts &Drift &DiftPins Metal Plate Connectors Hangers & Framing Anchors Staples Reference NDS or NER NDS or NER NDS or NER NDS or NER NDS NDS NDS NER NER NER National Evaluation Reports (NER) are developed for proprietary products Center-Point Bending Test Load 6 Yield Modes Single & double shear Wood-to-wood Wood-to-Steel Wood-to-Concrete

15 Nail Types and Designations Nail types described in Appendix L I II III IV Nail Types and Designations Nail capacity tables in 2005 NDS

16 l l NDS The length of dowel bearing shall not include the length of the tapered tip of a fastener for fastener penetration lengths less than 10D. ne shear plan use D r D r shear plane

17 Because the induced maximum moment can occur in the threads if the shear plane is not located sufficiently i into the shank away from the threads

18 Group Action Factor, C g Equation method C g 2n m(1 m ) 1 R n 2n n 1 REAm 1 m 1 m 1 m EA where: R EA EsA the lessor of E A m u u 2 1 s 1 u 1 2 Em A m m s m 1 E A s EmA or E A s s m s Group Action Factor, C g Group Action Factor, C g Not applicable here - loads acting along the length of the member are unit loads Bottom Plate Anchor Bolts and Washers as required

19 Appendix E - Local Stresses in Fastener Groups

20 Appendix E NDS Expressions Net tension: Z ' NT F A ' t net Appendix E NDS Expressions Group tear-out Z ' GT Z ' RT top 2 Z ' RT bottom 2 ' t F A groupnet Row tear-out: Z Z ' RTi ' RT ' n F ts n i row i1 v Z ' RTi min Note: spacing between outer rows of fasteners paralleling the member on a single splice plate < 5

21 Chapter 13 Timber Rivets Rivets Steel AISI 1035 Rockwell Hardness C32-39 F u = 145 ksi Hot-dipped galvanized Plates Steel ASTM A36 Hot-dipped galvanized if in wet service

22

23

24

25 Hidden kerf plates

26

27

28

29 Connections design software

30 ?

31 Questions? This concludes The American Institute of Architects Continuing Education Systems Course