Segmental ring types provided by F P McCann: Segments in stock are front bolted. Back bolted segments are available to order: Cross joint Corbel Ring

Size: px
Start display at page:

Download "Segmental ring types provided by F P McCann: Segments in stock are front bolted. Back bolted segments are available to order: Cross joint Corbel Ring"

Transcription

1 Building Manual for F P McCann `Smoothbore Shaft Linings with EPDM Gaskets (rev 04) (To be read in conjunction with the Segmental Shaft and Tunnel Safety Data Sheet) Segmental ring types provided by F P McCann: Segments in stock are front bolted. Back bolted segments are available to order: 1. Standard rings 2. Corbel rings 3. Recessed rings (standard, choker or cutter choker) * 4. Choker rings * 5. Combined cutter choker rings * made to order Cover Slab Circle joint Standard Ring Cross joint Corbel Ring Landing slab Cutter Choker Ring General All rings, with the exception of the cutter choker comprise of ordinary segments and two top segments. The top segments have one tapered cross joint in order that they can be installed with EPDM gasket. The cutter choker comprises all ordinary segments. All segments are supplied with a factory fitted EPDM gasket as the primary sealing system. Cross joint connections are made using a spear bolt passing through a pocket in one segment and a plastic socket in the adjacent segment. Circle joint connections are made using a T bolt passing through a hole in one segment and into a T box in the adjacent segment.

2 Segment Handling 1. Lifting All segments, with the exception of the cutter choker, are delivered vertical. Segments are lifted using F P McCann T fingers which locate into T box type sockets, cast into the segments. No other T finger should be used. There will be either two or four specified lifting positions depending on segment size, all of which must be used. The Safety Data Sheet provides the relevant information with regard to the lifting equipment required when using either static or moving crane. Refer to diagram below for minimum chain angles. Alternatively a spreader beam may be used. Crane hook Crane hook To secure the T finger, lift the sliding safety catch and insert into the full depth of the T box and turn through 90. Pull back until the T head of the bolt engages into the two internal clips. Push the safety catch into the T box to prevent the assembly from becoming accidentally disengaged. The cutter choker is delivered horizontal and should be turned on site. The T boxes and fingers should not be used for turning. The units should be turned either with slings (supplied by others) or using the 2 no threaded sockets cast into the circle joint. The appropriate lifting loops should be used (supplied by others). 2. Storage / Stacking Segments for shafts are typically stacked vertically. When stacked in this manner the first row should be placed on two timber bearers on even and firm ground. Subsequent rows, placed on top, should be separated with two timber bearers. Further measures will need to be taken to ensure the stacks are stable. The maximum height the segments should be stacked is two unless otherwise instructed by the Site Engineer. Stabilizing bars First row

3 Shaft design The rings / segments are designed by F P McCann for handling and installation only. The overall shaft design should be undertaken by the Scheme Engineer. For advice contact F P McCann Technical Department. Building Sequence Three methods of installation are described in this document. The sequences of installation are indicative and the exact method of installation is the responsibility of the Contractor. Health and Safety measures that apply specifically to segments and their fittings are indicated, other measures that apply to the shaft construction e.g. temporary guard rails to the top of the shaft, are the responsibility of the Contractor. For all methods the bitumen packers are required and are supplied. These packers should be secured to one cross joint face of each segment. A building tool is available from F P McCann to lift, locate and turn the T bolts into the correct orientation. Long reach sockets are available from F P McCann for fixing of the cross and circle joint bolts.

4 Building Sequence Underpinning Method The installation should proceed as follows: - Excavate a circular hole, typically to accommodate one or two rings and the concrete collar. Build the rings to correct line and level to the surface see `Building sequence Chimney fashion. Locate reinforcing bars through the wall. Pour the concrete collar. Note: The reinforcing bars and collar should be of sufficient strength and size to be capable of anchoring the rings, thereby supporting the weight of subsequent rings before grouting. Excavate the depth of 1.5 rings. The excavation should extend approximately 50mm beyond the outside diameter of the rings. Excavated area

5 Offer up the first ordinary segment to the ring above using an underpinning frame with all T bolts hanging in the through holes. Place the segment approximately 300mm below its intended position, with the centre of the segment directly underneath a joint on the ring above. Supports should be placed on top of the segment to avoid trapped hands should the segment be lifted unexpectedly. Lift and locate the `T bolts into the segments above, turning each clockwise through 90 and pulling downwards to lock them in position. A slot is located at the end of the thread. The slot should be in the correct orientation in the locked position i.e. radial. Optional: Insert one number locking wedge into the each T box. T Box Insert wedge into T box T bolt Wedge Check that the slot on the threaded end of each bolt points towards the centre of the shaft. Evenly tighten the `T bolts. Repeat the sequence until the gasket is compressed taking care not to overtorque any bolt as this may result in stripping of the threads. * Typical torques required range between 100Nm and 150Nm. 200Nm should not be exceeded without discussion with FM Technical Department. The degree of gasket compression required is dependent on the water pressure to be resisted. It should be noted that the circle joint has a flatness tolerance therefore full closure of the joint cannot be expected. Contact FPM Technical Department for further assistance if required.

6 The relative position of the bolts and the gasket may result in some `birds mouthing. The use of timber shims or wedges at the intrados of the joint, which should be removed as the joint is closed, can correct this. Check the segment for plumb. The underpinning frame should remain in position until all T bolts are fully tightened. The T bolt is not intended or designed to perform as a safety device. Site assessments should be undertaken by the installer and provisions made to ensure the safety of persons installing segments. When building the next and subsequent ordinary segments, follow the sequence as described below: Lubricate the gaskets on the mating surfaces of the segment. Offer the unit up using an underpinning frame and engage the `T bolts and locking wedge as described previously. Lift the segments and tighten the `T bolts to close the circle joint sufficient to position spear bolts into sockets on cross joint. The cross joint bolts may now be located and tightened to achieve a cross joint width of approximately 5mm. Evenly tighten all bolts within the circle and cross joints to compress the gasket. *Typical torques required range between 100Nm and 150Nm. 200Nm (T bolt) and 150Nm (cross joint bolts) should not be exceeded without discussion with FPM Technical Department. The degree of gasket compression required is dependent on the water pressure to be resisted. It should be noted that the circle joint faces have a flatness tolerance therefore full closure of the joint cannot be expected. Contact FPM Technical Department for further assistance if required. When building the top segments follow the sequence as described below: Install the first top segment as described above with the wide side uppermost. Offer up the second top segment. It may be necessary to excavate the ground locally to an additional depth in order to insert the last unit. Tighten the bolts as described for the ordinary segments. Close the gap between the excavation and the rings and grout the shaft through the grout sockets / non return valves cast into the segments. Fit the grout plugs on completion. Important note no more than one ring should be erected before grouting.

7 Repeat the process for all subsequent rings. A base slab may then be cast under or within the bottom of the shaft. The installation of seals will be required to avoid tracking of water through vertical holes, segment joints and between the base slab and the rings. For advice contact F P McCann Technical Department. The details below are typical and do not apply to all shafts.

8 Fixings may be either single or double row depending on shaft diameter T Box EPDM gasket Fill void at caulking groove with Tunnelling Accessories `Aquaflex' sealant Through holes to be sealed using T Bolt and Tunnelling Accessories Hydrophilic `Puh' washer 40 O/d x 16 I/d x 4 thk. T Bolt Tunnelling Accessories Hydrophilic sealing strip ref S204 around circumference of shaft 50 min. Insitu concrete 50 min. One layer, of Tunnelling Accessories Hydrophilic sealing strip ref S204, per cross joint (trim bituminous packer to suit) Bolt pocket Insitu concrete Section through T bolts Section through Cross joint Insitu concrete base plug The rings may be caulked and pointed.

9 Building Sequence Caisson method The shaft may either be sunk using a F P McCann combined concrete cutter/choker ring or a steel cutting edge (supplied by others). The installation should proceed as follows: Excavate a circular hole, typically to accommodate one or two rings and the concrete collar. Build the cutter choker ring to correct line and level, using either a concrete cutter choker ring or steel cutting edge secured to either a concrete choker ring or concrete standard ring. Steel cutting edge. Short T bolts are available to secure the steel cutter to the concrete ring over. Lift, locate and tighten the short T bolts through the steel plate into the T boxes located on the underside of the first concrete ring. The first concrete ring may be a standard ring or choker ring.

10 Concrete cutter choker. Standard length T bolts are provided to secure the concrete cutter choker ring to the concrete ring over. Place all T bolts in the through holes of the concrete cutter choker ring (T section uppermost). Place supports on the top of each segment to avoid trapped hands as the segment over is lowered into position. Lift and locate the `T bolts into the segments above, turning each clockwise through 90 and pulling downwards to lock them in position. A slot is located at the end of the thread. The slot should be in the correct orientation in the locked position i.e. radial. The installation of seals to avoid tracking of water through the vertical holes and segment joints may be required at this stage. For advice contact F P McCann Technical Department (Refer to base sealing diagrams at the end of this section). Wrap sheets of polystyrene or other suitable material around the extrados of the ring(s) to provide an annulus between the collar and the rings, which can be filled with bentonite slurry if required. Note: The F P McCann choker increases the segment width by 50mm. Pour the concrete collar. Note: The collar should be of sufficient size and strength to be capable of supporting the hydraulic rams. Install the hydraulic rams. Lower the first ordinary segments to the ring below with the required `T bolts hanging downward in the through holes. For sizes up to and including 7.5 ID, only two T bolts are required which should

11 be placed in the inner through holes. Note: Other holes are provided for installation using the underpinning method. Place supports on the top of each segment to avoid trapped hands as the segment over is lowered into position Lower the segments onto supports with the segment centre directly above a joint on the ring below. Locate the `T bolts into the segments below, turning each clockwise through 90 and pulling upwards to lock them in position. A slot is located at the end of the thread. The slot should be in the correct orientation in the locked position i.e. radial. Optional: Insert one number locking wedge into each T box. Wedge T bolt Insert wedge fully into T box T Box The supports should then be removed; taking care to avoid trapped hands should the segment move unexpectedly. The segments can then be lowered into the correct position. Check that the slot on the threaded end of each bolt points towards the centre of the shaft. Evenly tighten the `T bolts. Repeat the sequence until the gasket is compressed taking care not to over-torque any bolt as this may result in stripping of the threads. * Typical torques required range between 100Nm and 150Nm. 200Nm (T bolt) should not be exceeded without discussion with FPM Technical Department. The degree of gasket compression required is dependent on the water pressure to be resisted. It should be noted that the circle joint has a flatness tolerance therefore full closure of the joint cannot be expected. Contact FPM Technical Department for further assistance if required.

12 The relative position of the bolts and the gasket may result in some `birds mouthing. The use of timber shims or wedges at the intrados of the joint, which should be removed as the joint is closed, can correct this. Check the segment for plumb. When building the next and subsequent ordinary segments, follow the sequence as described below: Lubricate the gaskets on the mating surfaces of the segment. Lower the unit supports onto the ring below, engaging the `T bolts as described previously. Remove the supports and lower the segments. Tighten the `T bolts sufficient to position spear bolts into sockets on cross joint. *Typical torques required range between 100Nm and 150Nm. 200Nm (T bolt) should not be exceeded without discussion with FPM Technical Department. The cross joint bolts may now be located and tightened to achieve a cross joint width of approximately 5mm *Typical torques required range between 100Nm and 150Nm. 150Nm (cross joint bolts) should not be exceeded without discussion with FPM Technical Department. Evenly tighten all bolts within the circle and cross joints to compress the gasket as previously described. When building the top segments follow the sequence as described below: Construct the first top segment as described above with the wide side downwards. Lower the second top segment. Tighten the bolts as previously Push the rings into the ground using the hydraulic rams or suitable kentledge spread evenly about the ring. Use bentonite slurry within the annulus around the shaft to assist sinking if required. Excavate the ground within the built rings. Care should be taken not over excavate to ensure that the shaft does not sink in an uncontrolled way. Push the rings to a depth to enable the next ring to be erected. Build the next ring as described above and the process repeated until the desired depth is achieved. Grout the shaft using the grout sockets / non return valves cast into the segments. Install the grout plugs on completion. A base slab may then be cast within the bottom of the shaft. The installation of seals will be required to avoid tracking of water through vertical holes, segment joints and between the base slab and the rings. For advice contact F P McCann Technical Department.

13 Concrete cutter choker base sealing details: The details below are typical and do not apply to all shafts.

14 T Box EPDM gasket T Bolt Smoothbore Cutter/Choker ring Tunnelling Accessories Hydrophilic `Puh' washer 40 O/d x 16 I/d x 4 thk. Fill void at caulking groove with Tunnelling Accessories `Aquaflex' sealant Tunnelling Accessories Hydrophilic sealing strip ref S204 around circumference of shaft 50 min. 50 min. Section through T bolt & Thru' hole Insitu concrete base plug Tunnelling Accessories Hydrophilic `Puh' washer 40 O/d x 16 I/d x 4 thk. Section through Cross joint One layer, of Tunnelling Accessories Hydrophilic sealing strip ref S204, per cross joint (trim bituminous packer to suit) Insitu concrete base Bolt pocket Steel cutting edge base sealing details: The details below are typical and do not apply to all shafts. McCann Standard Smoothbore ring Through holes to be sealed using epoxy mortar or other, prior to shaft construction, to prevent possible water paths. Bottom ring only T Box 150 long Tee Bolt Insitu concrete base plug Steel Cutter ring (Supplied by others) Section through Tee bolts Section through Thru' hole

15 EPDM gasket Fill void at caulking groove with Tunnelling Accessories `Aquaflex' sealant Tunnelling Accessories Hydrophilic sealing strip ref S204 around circumference of shaft 50 min. 50 min. One layer, of Tunnelling Accessories Hydrophilic sealing strip ref S204, per cross joint (trim bituminous packer to suit) Bolt pocket Section through Cross joint

16 Building Sequence Chimney fashion The installation should proceed as follows: Excavate the ground to the required depth for the shaft. Cast a base slab in the bottom of the excavation. The installation of seals to avoid tracking of water through the vertical holes and segment joints may be required at this stage. Refer to diagrams for base sealing for the underpinning method. These details are typical and do not apply to all shafts For advice contact F P McCann Technical Department Place the segments into position and bolt to adjacent segments until a complete ring is built. Lower the first ordinary segments to the ring below with the required `T bolts hanging downward in the through holes. For sizes up to and including 7.5 ID, only two T bolts are required which should be placed in the inner through holes. Note: Other holes are provided for installation using the underpinning method. Place supports on the top of each segment to avoid trapped hands as the segment over is lowered into position Lower the segments onto supports with the segment centre directly above a joint on the ring below. Locate the `T bolts into the segments below, turning each clockwise through 90 and pulling upwards to lock them in position. A slot is located at the end of the thread. The slot should be in the correct orientation in the locked position i.e. radial.

17 Optional: Insert one number locking wedge into each T box. Wedge T bolt Insert wedge fully into T box T Box The supports should then be removed; taking care to avoid trapped hands should the segment move unexpectedly. The segments can then be lowered into the correct position. Check that the slot on the threaded end of each bolt points towards the centre of the shaft. Evenly tighten the `T bolts. Repeat the sequence until the gasket is compressed taking care not to over-torque any bolt as this may result in stripping of the threads. *Typical torques required range between 100Nm and 150Nm. 200Nm (T bolt) should not be exceeded without discussion with FPM Technical Department. The degree of gasket compression required is dependent on the water pressure to be resisted. It should be noted that the circle joint has a flatness tolerance therefore full closure of the joint cannot be expected. Contact FPM Technical Department for further assistance if required. When building the next and subsequent ordinary segments, follow the sequence as described below: Lubricate the gaskets on the mating surfaces of the segment. Lower the unit supports onto the ring below, engaging the `T bolts as described previously. Remove the supports and lower the segments. Tighten the `T bolts sufficient to position spear bolts into sockets on cross joint. *Typical torques required range between 100Nm and 150Nm. 200Nm (T bolt) should not be exceeded without discussion with FPM Technical Department. The cross joint bolts may now be located and tightened to achieve a cross joint width of approximately 5mm *Typical torques required range between 100Nm and 150Nm. 150Nm (cross joint bolts) should not be exceeded without discussion with FPM Technical Department. Evenly tighten all bolts within the circle and cross joints to compress the gasket as previously described. When building the top segments follow the sequence as described below: Construct the first top segment as described above with the wide side downwards. Lower the second top segment. Tighten the bolts as previously Repeat the process for all subsequent rings. The void around the shaft may be back filled using a granular fill or concrete. This should be placed and compacted evenly around the shaft to avoid uneven loading.the Scheme Engineer should advise on the method that is suitable as it is dependent on ground conditions and use of shaft.

18 Important notes: 1 It is important that the circularity of the rings are maintained throughout the installation process as any deflection will most likely increase as the shaft is installed. The segment connections are designed to allow some ovality but if this is exceeded then cracking and subsequent failure of the concrete around the fittings could take place. 2 Should the shaft be pointed before the water pressure is allowed to act on the shaft then spalling of the concrete along the caulking groove could result due to load transfer through the pointing. *The recommended torques are based on clean sheradised bolts with no lubricant applied. The torque is very dependent on the friction in the system i.e. condition of the bolts / sockets on site, therefore these are for guidance only. Ancillary Items Available from F P McCann or recommended specialist supplier Shaft slabs Pre cast cover and landing slabs. Shaft fittings Tie rod type fittings to allow segments to be built `in-line. Short `T bolts - for fixing the steel cutter to the choker ring. Locking wedges for T boxes. Shaft specialist building equipment / materials A T bolt long reach socket - used when tightening the `T bolts. A spear bolt long reach socket used when tightening the spear bolts. T bolt building tools used for pulling the `T Bolt head into the internal clips in the `T box. T lifting fingers see segment handling. Underpinning frame (underpinning building method only) Grout socket adaptors used as an adaptor for grouting equipment. Grout socket lifting ball used for lifting horizontally in special circumstances Hydrophyllic washers used for sealing though holes. (Refer to base sealing details within installation sequence) Hydrophyllic strip used for sealing segment joints and as a circumferential base seal. Refer to base sealing details within installation sequence) Lubricant for gaskets

19

connecting the world PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor

connecting the world PDF compression, OCR, web optimization using a watermarked evaluation copy of CVISION PDFCompressor C O N S T R U C T I O N I W I N D E N E R G Y I T U N N E L L I N G I R A I L I O E M connecting the world the tunnelling market Tunnelling is a key facet of infrastructure development particularly where

More information

Please read and understand all instructions before beginning. These instructions cover impact and non-impact aluminum French Door 650/750.

Please read and understand all instructions before beginning. These instructions cover impact and non-impact aluminum French Door 650/750. The performance and proper operation of a door is only as good as the installation. By following these instructions, the probability of a good installation greatly increases. Please read and understand

More information

INSTALLATION GUIDE PermaTrak. Patented Product: U.S. Patent #5,906,084 #8,302,362 #8,522,505 #8,839,588 #9,096,975

INSTALLATION GUIDE PermaTrak. Patented Product: U.S. Patent #5,906,084 #8,302,362 #8,522,505 #8,839,588 #9,096,975 INSTALLATION GUIDE 2009-2017 PermaTrak. Patented Product: U.S. Patent #5,906,084 #8,302,362 #8,522,505 #8,839,588 #9,096,975 Table of Contents Project Overview Forward, Acceptability Criteria, Safety,

More information

3.2.3 Rear Door Window and Quarter Window Carrier Assembly

3.2.3 Rear Door Window and Quarter Window Carrier Assembly Tighten all bolts. Tighten bolts marked -1- and -2- in specified sequence. Tightening torque: 8 Nm Remaining bolts can be tightened in any sequence. Insert door window -3- through window recess without

More information

Installation Instructions

Installation Instructions Installation Instructions 200 Series Curtainwall 3056 WALKER RIDGE DR. NW, SUITE G WALKER, MI 49544 800-866-2227 dependable@tubeliteinc.com Revised April 2014 dependable@tubeliteinc.com Page 1 TABLE OF

More information

Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe

Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe INFORMATION The Stargrip Mechanical Joint Restraint System is a unique product with a proven design that provides an exceptional

More information

PEDESTAL OVERHAUL. Some of the tools for a pedestal overhaul. Pedestal work stand

PEDESTAL OVERHAUL. Some of the tools for a pedestal overhaul. Pedestal work stand INTRODUCTION A properly greased labyrinth seal will help prevent dust and water damage to the pedestal bearing oil supply and shaft seal area. Properly greased and oiled pedestals rarely require an overhaul.

More information

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back HSF 250 Patriot Heavy Duty Line Stop Fitting - 4, 6, 8 inch Nominal Sizes Line Stop Fitting Installation Instructions Push and Pin Completion Plug Installation Instructions IMPORTANT: Read installation

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

INSTALLATION, OPERATION AND MAINTENANCE MANUAL INSTALLATION, OPERATION AND MAINTENANCE MANUAL STOP LOGS O&M STOP LOGS REVA PAGE 1 We are a Glasgow based company providing water engineering solutions in fluid control for both the UK and International

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Tools required for the installation. A. Core Drill 87mm Drill bit B. Tape measure C. Spirit Level D. Marking pen E. Caulking gun F. Cutting Pliers G. Cordless Drill and Philips head bit, 5mm Drill bit.

More information

NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions

NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE. Installation Instructions NARROW, MEDIUM AND WIDE STILE, THERMASTILE AND DURASTILE Installation Instructions PART Y015 JUNE 2016 Table of Contents Section 1. GENERAL NOTES AND GUIDELINES... 2. DOOR HARDWARE A. Locks B. Push/Pulls

More information

I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS

I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS I n s t a l l a t i o n I n s t r u c t i o n s S E N T I N E L S E R I E S 1 50 SLIDING GLASS DOORS Page 2-9: Installation Instructions, Figures 1, 2, & 3 Page 10-12: Figures A-1, A-2, & A-3: Installation

More information

RBP-1215B-RX DODGE RAM QUAD CAB RX3

RBP-1215B-RX DODGE RAM QUAD CAB RX3 RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side

More information

Step by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com

Step by Step Installation Instructions. Poly Shutters. Customer Service or visit us online at smithandnoble.com Step by Step Installation Instructions Poly Shutters Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from smith+noble. Your new window treatments have been

More information

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS

1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS 1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Tools required for the installation. A. Core Drill 87mm Drill bit B. Tape measure C. Spirit Level D. Marking pen E. Caulking gun F. Cutting Pliers G. Cordless Drill and Philips head bit, 5mm Drill bit.

More information

Additional Information

Additional Information NUMBER: 1 34 13 S.M. REF.: Listed in Table ENGINE: EPA04/07 Series 60 DATE: January 2013 SUBJECT: CHECKING CYLINDER LINER PROTRUSION ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section

More information

Dura-Lock Roof System

Dura-Lock Roof System DLR-14 Dura-Lock Roof System Assembly and Installation Instructions Read the instructions before starting the job. They explain the steps required to produce a finished product that will meet factory specifications.

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

INSTALLATION, OPERATION AND MAINTENANCE MANUAL INSTALLATION, OPERATION AND MAINTENANCE MANUAL HANDSTOP O&M HANDSTOP REVA PAGE 1 We are a Glasgow based company providing water engineering solutions in fluid control for both the UK and International

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant

More information

FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF55 & SF75 WITH WEATHERED OR FLUSH TRACK

FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF55 & SF75 WITH WEATHERED OR FLUSH TRACK FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF55 & SF75 WITH WEATHERED OR FLUSH TRACK Please refer to your order or detailed sectional drawing (if requested) to assist you with the configuration

More information

PFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids

PFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids Maximum Flat Panel Weight: 160 lb. / 72.57 kg. Included Components Wall Mount (Qty 1) Extension Brackets (Qty 2) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver

More information

TREX PERGOLA INSTALLATION INSTRUCTIONS

TREX PERGOLA INSTALLATION INSTRUCTIONS RECOMMENDED TOOLS/SUPPLIES: Pencil 4' Level Measuring Tape Framing Square/Speed Square 8' High Step Ladder (Two recommended) Hacksaw or Bolt Cutters Socket Wrench with 9/16" Socket and 3/4" Deep Socket

More information

101B, 210X, ELM, VSTB Installation Manual

101B, 210X, ELM, VSTB Installation Manual 101B, 210X, ELM, VSTB Installation Manual 99-16105-I001 Copyright 2010 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in examples

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: Series 50/50G DATE: October 2013 SUBJECT: MACHINING CYLINDER BLOCK COUNTERBORES

NUMBER: S.M. REF.: Listed in Table ENGINE: Series 50/50G DATE: October 2013 SUBJECT: MACHINING CYLINDER BLOCK COUNTERBORES NUMBER: 10 25 13 S.M. REF.: Listed in Table ENGINE: Series 50/50G DATE: October 2013 SUBJECT: MACHINING CYLINDER BLOCK COUNTERBORES ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section

More information

Pow-R-Feed Systems Service Manual

Pow-R-Feed Systems Service Manual Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious

More information

PUSH-PULL-PROPS. and accessories ROBUSTA-GAUKEL GMBH MOUNTING TECHNOLOGY &CO.KG

PUSH-PULL-PROPS. and accessories ROBUSTA-GAUKEL GMBH MOUNTING TECHNOLOGY &CO.KG PUSH-PULL-PROPS and accessories MOUNTING TECHNOLOGY ROBUSTA-GAUKEL GMBH &CO.KG MOUNTING TECHNOLOGY PUSH-PULL-PROPS AND ACCESSORIES INDEX General information...................... 3 Push-pull-prop Type

More information

General Four-Way Operation, Maintenance & Service Manual

General Four-Way Operation, Maintenance & Service Manual General Four-Way Operation, Maintenance & Service Manual SCOPE Included in the following pages you will find assembly drawings, exploded views, parts lists, assembly tips, operational descriptions and

More information

Pickup Box Utility Rack Package Installation (Instruction ID: )

Pickup Box Utility Rack Package Installation (Instruction ID: ) 017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation

More information

Model 209 Fireback Replacement

Model 209 Fireback Replacement Model 209 Fireback Replacement Please read all the instructions before you begin the procedure. Confirm that you have all the necessary tools and materials. If you have any questions, technical support

More information

ALL SEASON PATIO COVER

ALL SEASON PATIO COVER ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the

More information

Door window. Front door window, assembly overview

Door window. Front door window, assembly overview 64-50 Door window Front door window, assembly overview 1 - Window channel Pushed onto flange 2 - Door window Removing Page 64-52 Adjusting Page 64-53 3 - Door 4 - Outer window channel Pushed onto flange

More information

Vanity Installation Instructions

Vanity Installation Instructions Vanity Installation Instructions Segments of these instructions will relate to your vanity. Please read these instructions thoroughly and ensure the appropriate instructions are used during the installation

More information

STRATUS SHELTER. Take bike parking to new heights

STRATUS SHELTER. Take bike parking to new heights Take bike parking to new heights The Stratus Shelter is a striking bike shelter option for any transit station, university campus, or multi-family residential building project. It is constructed of American

More information

Bumper Sign INSTALLATION INSTRUCTIONS

Bumper Sign INSTALLATION INSTRUCTIONS Bumper Sign INSTALLATION INSTRUCTIONS BUMPERSIGN TOOL CHECKLIST SDS MAX Rotary Hammer Drill Marker/Pencil SDS MAX 1 Carbide Drill Bit Tape Measure Torque Wrench with ½ Drive Power Source Vacuum ½ Drive

More information

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models -J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com

More information

Clamping devices 521

Clamping devices 521 Clamping devices 521 522 Product overview Clamping devices Adjustable straps K0001 Hook clamps K0012 Goose-neck straps with long slot K0002 Page 526 Hook Clamps with collar K0013 Page 535 Equipped clamps

More information

MODEL T TON HYDRAULIC PRESS INSTRUCTIONS (For Machines Mfd. Since 10/17)

MODEL T TON HYDRAULIC PRESS INSTRUCTIONS (For Machines Mfd. Since 10/17) MODEL T1241 20-TON HYDRAULIC PRESS INSTRUCTIONS (For Machines Mfd. Since 10/17) For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Identification

More information

Spring Loaded All Season Roll-Up Doors

Spring Loaded All Season Roll-Up Doors Spring Loaded All Season Roll-Up Doors STAND-OFF MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately

More information

B-Too Drilling and Tapping Machine Instruction and Maintenance Manual

B-Too Drilling and Tapping Machine Instruction and Maintenance Manual B-Too Drilling and Tapping Machine Instruction and Maintenance Manual Thank you for your purchase of the B-Too Drilling and Tapping Machine. Please read and understand this short operation manual. Our

More information

Portofino Case2 Installation Guide

Portofino Case2 Installation Guide Portofino Case2 Installation Guide vjun16 (for 17 or 24 mm Surface Wall Profile) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino Case 2 shower enclosure.

More information

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF75H

FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF75H FITTING INSTRUCTIONS FOR FOLDING SLIDING DOOR SYSTEM SF75H 01603 424434 Please refer to your order or detailed sectional drawing (if requested) to assist you with the configuration of the system supplied

More information

Shetland Stalls Installation Instructions

Shetland Stalls Installation Instructions Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions INTRODUCTION Congratulations! You are the owner of the finest rotary-style gasket cutter in the world. Originally developed and patented

More information

BEST PRACTICE GUIDE. Socket Bases. Working with Concrete Slabs

BEST PRACTICE GUIDE. Socket Bases. Working with Concrete Slabs Working with Concrete Slabs When working with concrete slabs the barrier protection can be erected in three ways - with socket bases, adjustable slab edge brackets and multi slab clamps. Socket Bases 1

More information

Fig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7

Fig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7 FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track

More information

Riser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18. Manual 40100X35-8

Riser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18. Manual 40100X35-8 Riser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18 Manual 40100X35-8 3 2 4 Access covers with bolts supplied with Interceptor 1 5 14 6 11 15 Sampling Port/Cleanout cap supplied with Interceptor 12

More information

Pull-down clamps. No Low height clamping jaws, model Bulle

Pull-down clamps. No Low height clamping jaws, model Bulle Pull-down clamps The wedge action of clamping jaws is the characteristic feature of these pull down clamps. It causes the pull down effect, which presses the workpiece against both, stop and machine table.

More information

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02 GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.

More information

18000 HDL FOUR POST LIFT LB CAPACITY INSTALLATION AND OWNER'S MANUAL

18000 HDL FOUR POST LIFT LB CAPACITY INSTALLATION AND OWNER'S MANUAL 18000 HDL FOUR POST LIFT 18000 LB CAPACITY INSTALLATION AND OWNER'S MANUAL WARNING! Do not raise a vehicle unless the front stops are in place, the parking brake is set, and the wheels are chocked. Stay

More information

GENERAL ISOMETRIC LAYOUT

GENERAL ISOMETRIC LAYOUT EXISTING OR PROPOSED WIPER WALL SUPPORT STRUCTURE GATE LID CARBATHAN HG 0 WEB GRAY LOWER PAN GRATING ALUMINUM WIPER WALL CARBATHANE HG, 90 GRAY STRUCTURAL SPECIFICATIONS:. FLOODGATE MATERIAL TO BE ALUMINUM

More information

Installation Instructions

Installation Instructions edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung

More information

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully

More information

Thank you for purchasing our product! *Please read these instructions and follow them step by step.*

Thank you for purchasing our product! *Please read these instructions and follow them step by step.* 07/07/08.rev1 PAGE 1 OF 11 601AL VERTICAL 60120VL LIFT W/CHAIN DRIVE WINCH Thank you for purchasing our product! *Please read these instructions and follow them step by step.* Step 1. Separate and group

More information

caroma marc newson wall basin mixer

caroma marc newson wall basin mixer caroma marc newson wall basin mixer water efficient tapware (nominal flow rate = 5 L/min) PLUMBERS INSTALLATION INSTRUCTIONS IS1213A(07/12) Important Information Brazed connections should NOT be made directly

More information

Fisher 667 Diaphragm Actuators Size 80 and 100

Fisher 667 Diaphragm Actuators Size 80 and 100 Instruction Manual 667 Size 80 and 100 Actuators Fisher 667 Diaphragm Actuators Size 80 and 100 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Maximum Pressure Limitations...

More information

MSR/MSB Mechanical Setting Tool

MSR/MSB Mechanical Setting Tool Tech Unit No: 0620000004 Revision: B Approved By: Quality Engineer Date: 2014-12-16 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review

More information

SM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL

SM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation

More information

WRS Artificial Lift System

WRS Artificial Lift System WRS Artificial Lift System Patent Pending Designed to adapt to any type of Artificial Lift Suspension! Artificial Lift and Down hole gauge monitoring Is fast Becoming the go to in the oil production market.

More information

Tuf-Lite II Fans H Hi Temp 3000HT Series Hub

Tuf-Lite II Fans H Hi Temp 3000HT Series Hub Tuf-Lite II Fans H Hi Temp 3000HT Series Hub INSTALLATION MANUAL Hudson Tuf-Lite II Hi Temp Fan Blades Adjustable Pitch Fan Assembly 5 through 14 Diameter Hudson Tuf-Lite II Hi Temp fan blades (Red) are

More information

method of build Komfire-75 partitioning system 75mm Steel Stud & Plasterboard Partitioning System with Square Aluminium Cover Trims KOMFORT

method of build Komfire-75 partitioning system 75mm Steel Stud & Plasterboard Partitioning System with Square Aluminium Cover Trims KOMFORT 821 811 342 821 835 853 863 840 12.5mm Plasterboard 837 75mm Steel Stud & Plasterboard Partitioning System with Square Aluminium Cover Trims Note: For clarity the cavity infill has not been shown 854 342

More information

Important Notices. Manway Lockout Point

Important Notices. Manway Lockout Point 2 Drawing CM-1B Important Notices 1. We palletize all manways to avoid damage during shipment and subsequent handling at the jobsite. We suggest that the manway remain on the pallet until installation.

More information

PVCu FOLD & SLIDE DOOR OUTWARD OPENING

PVCu FOLD & SLIDE DOOR OUTWARD OPENING PVCu FOLD & SLIDE DOOR OUTWARD OPENING STEP-BY-STEP FULLY ILLUSTRATED ASSEMBLY INSTRUCTIONS This product is covered by a 10 year manufacturer s guarantee. Should any part of it become defective due to

More information

Optimast Installation Method Statement. F108.

Optimast Installation Method Statement. F108. Optimast Installation Method Statement. F108. Contents Page 1) Product Description. 2) Durability....... 3) Profile & Baseplate..... 4) Anchor Cradle and Foundation Stud Set Detail Drawings 4a) 127...

More information

INSTALLATION GUIDE Timber Stairs

INSTALLATION GUIDE Timber Stairs INSTALLATION GUIDE Timber Stairs A Guide to Safe Stair Installation from the BWF Stair Scheme British Woodworking Federation 2018 Introduction Contents Introduction Page 3 Assembly 3.1 Straight flight

More information

Clamping bolts Eccentrical cams clamping units

Clamping bolts Eccentrical cams clamping units 2.3 Shaft Clamping bolts Eccentrical cams clamping units 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 2.3 Clamping bolts, Eccentrical cams, Shaft clamping units Page 641 2.3 Clamping bolts, Eccentrical cams, Shaft

More information

SLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE

SLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE Set A Set B P7001 Standard Kit Glass Door FITTING INSTRUCTIONS SUGGESTED TOOLS DRILL MITRE/CHOP SAW TAPE MEASURE (Image for reference only) HACKSAW POCKER DOOR KIT SHORT / LONG Z SECTION LONG Z SECTION

More information

SLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE

SLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE Set A Set B PFD30 Fire Door Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors IF INSTALLING A TOUCH LATCH, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS FIRST

More information

Assembly Instructions

Assembly Instructions InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective

More information

ENGINEERING STRENGTH INSTAL L AT I O N M A NUAL OUR STRENGTH IS OUR STRENGTH

ENGINEERING STRENGTH INSTAL L AT I O N M A NUAL OUR STRENGTH IS OUR STRENGTH ENGINEERING STRENGTH INSTAL L AT I O N M A NUAL OUR STRENGTH IS OUR STRENGTH RAFTER PREPERATION RAFTER PREPARATION A FRAME PREPERATION AND ASSEMBLY A FRAME PREPARATION AND ASSEMBLY... Open boxes, remove

More information

HDL(M)6 Nut/Screw Assembly

HDL(M)6 Nut/Screw Assembly HDL(M)6 Nut/Screw Assembly Remove, repair, and reassemble the nut and screw assembly in your HDL series double lock vise. In these instructions when we refer to the front of the vise or nut/screw assembly,

More information

Installation, Operation and Maintenance Manual. RB Weir Gate

Installation, Operation and Maintenance Manual. RB Weir Gate Installation, Operation and Maintenance Manual RB Weir Gate INDEX Introduction. Handling and Storage Installation... Weir Gate installation. Concrete Wall Mounted..... Concrete Round Manhole Wall Mounted.

More information

Due to possible damage in shipping, the vertical stop assembly has been removed from this machine.

Due to possible damage in shipping, the vertical stop assembly has been removed from this machine. Due to possible damage in shipping, the vertical stop assembly has been removed from this machine. To assemble, insert the threaded rod through the shroud opening in the top of the machine. Start the four

More information

Pocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.

Pocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents. Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: O-Ring Groove Cutter Page 1 of 6 Kit Contents: 1x Cutter Head Assembly with Handle & Adjustable Tool Block 1x Graduated Adjusting Screw 1x Adjustable Tool Holder 1x Carbide Insert (Size of

More information

Vinyl Sliding Glass Door Assembly Instructions

Vinyl Sliding Glass Door Assembly Instructions Vinyl Sliding Glass Door Assembly Instructions SERIES SGD 5470/5570 Para instrucciones en español, visite: http://bit.ly/pgtassemblyinstructions Parts List ITEM 4 5 6 7 8 9 0 4 5 6 7 8 SGD 5470/5570 PARTS

More information

YCW 752 Outside Glazed Curtain Wall System Installation Manual

YCW 752 Outside Glazed Curtain Wall System Installation Manual YCW 752 Outside Glazed Curtain Wall System Installation Manual 2007 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................

More information

SLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE

SLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE Set A Set B PFD30 SG Fire Door Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors SUGGESTED TOOLS DRILL G-CLAMP TAPE MEASURE (Image for reference only) HACKSAW POCKET

More information

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual

YCW 750 OG Outside Glazed Curtain Wall System Installation Manual YCW 750 OG Outside Glazed Curtain Wall System Installation Manual 2004 YKK AP America Inc. is a subsidiary of YKK Corporation of America. TABLE OF CONTENTS Installation Notes........................................

More information

SLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE

SLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE Set A Set B P7001 Standard Kit FITTING INSTRUCTIONS For use with 44mm thick doors only For Single and Double doors IF INSTALLING A TOUCH LATCH, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS FIRST

More information

M4 Foot Operated Underpinner Instruction Manual

M4 Foot Operated Underpinner Instruction Manual M4 Foot Operated Underpinner Instruction Manual M4 Walker Rd, Bardon Hill, Coalville, Leicestershire LE67 1TU, England Tel. +44 (0)130 1692, Fax +44 (0)130 16929 e mail sales@framerscorner.co.uk M4 Underpinner

More information

AIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS

AIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS AIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS GENERAL INFORMATION...1 Freight Damage... 1 Repairing Paint Scratches...1 BASE CABINETS... 2 Drawer Removal and Reinstallation...2 Replacing Drawer

More information

Deauville Installation Guide

Deauville Installation Guide vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last

More information

IF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST

IF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST Set A Set B PFD60 Fire Door Kit FITTING INSTRUCTIONS IF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST SUGGESTED

More information

Deauville Installation Guide

Deauville Installation Guide vjul16 (for Recessed Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Deauville shower enclosure. Please study these instructions carefully before

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com

More information

OB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount

OB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description

More information

Oxford Stalls Installation Instructions

Oxford Stalls Installation Instructions Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or

More information

Hardened Structures Hardened Shelters, LLC. Explosion Resistant Pre-hung Sealed Blast Door

Hardened Structures Hardened Shelters, LLC. Explosion Resistant Pre-hung Sealed Blast Door Hardened Structures Hardened Shelters, LLC Explosion Resistant Pre-hung Sealed Blast Door Drawing number: ASR-50-BD Revision: E Date: December 8, 2008 Table of Contents Contact Information... 3 Description...

More information

Installation Instructions

Installation Instructions For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp

More information

Fisher 667 Diaphragm Actuator Sizes 30/30i 76/76i and 87

Fisher 667 Diaphragm Actuator Sizes 30/30i 76/76i and 87 Instruction Manual 667 Actuator (Size 30/30i - 76/76i and 87) Fisher 667 Diaphragm Actuator Sizes 30/30i 76/76i and 87 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...

More information

TYPE 3740/3740D WET/DRY RUNNING CARTRIDGE SPLIT SEAL

TYPE 3740/3740D WET/DRY RUNNING CARTRIDGE SPLIT SEAL 1 Foreword These instructions are provided to familiarize the user with the seal and its designated use. The instructions must be read and applied whenever work is done on the seal, and must be kept available

More information

a.k.a. casegoods instructions

a.k.a. casegoods instructions a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly

More information

Maintenance & Parts list for:

Maintenance & Parts list for: Maintenance & Parts list for: Industrial gun GB 2 Juni 2017 This Maintenance & Parts list for industrial gun is prepared by : Winchester Europe Service V. Parbst & Søn as a comprehensive maintenance guide

More information

Series Sloped glazed Curtain wall. Installation Instructions

Series Sloped glazed Curtain wall. Installation Instructions Series 5600 Sloped glazed Curtain wall Installation Instructions Part NO. Y308 February 2013 SECTION TABLE OF CONTENTS PAGE I. General Notes & Guidelines. 3-4 II. Gutter and Mullion Assembly.. 5 III. End

More information