Fasteners. Bolts. NAPA FastTrack Counter Sales Training Fasteners Page 1. Figure 1. Typical Measurements for a Bolt or Hex Head Cap Screw
|
|
- Franklin Copeland
- 5 years ago
- Views:
Transcription
1 Fasteners Many types and sizes of fasteners are used in the automotive industry. Each fastener is designed for a specific purpose and condition. One of the most commonly used type of fastener is the threaded fastener. Threaded fasteners include bolts (also called cap screws), nuts, screws and similar items that allow a part to be easily installed or removed. Over the years, a number of terms have been used to identify the various types of fastener threads. The Unified National Series consists of four basic classifications. Unified National Coarse (UNC or NC) (USS) Unified National Fine (UNF or NF) (SAE) Unified National Extrafine (UNEF or NEF) Unified National Pipe Thread (UNPT or NPT) Two thread styles are most commonly used on inch fasteners: UNC-USS coarse thread and UNF-SAE fine thread. Fine thread fasteners provide about 10% more clamping force than coarse thread fasteners of the same size and grade. Clamping force is the amount of tension force that holds two or more pieces together when a fastener is tightened. The two common metric threads are coarse and fine and can be identified by the letters SI (Systeme International d Unites or International System of Units) or ISO (International Standards Organization). Bolts A bolt has several parts (Figure 5). The bolt head is used to tighten the bolt. A socket or wrench fits over the head, which enables the bolt to be tightened. Bolt diameter is the measurement across the major diameter of the threaded area or across the bolt shank. The thread pitch of a bolt in the English system is determined by the number of threads that are in one inch of threaded bolt length and is expressed in number of threads per inch. The thread pitch in the metric system is determined by the distance in millimeters between two adjacent threads. Bolt length is the distance measured from the bottom of the head to the tip of the bolt. The bolt s tensile strength, or grade, is the amount of stress or stretch it is able to withstand. Figure 1. Typical Measurements for a Bolt or Hex Head Cap Screw NAPA FastTrack Counter Sales Training Fasteners Page 1
2 The type of bolt material and the diameter of the bolt determine its tensile strength. In the English system, the tensile strength of a bolt is identified by the number of radial lines (grade marks) on the bolt head (Figure 6). More lines mean higher tensile strength. In the metric system, tensile strength of a bolt or stud can be identified by a property class number on the bolt head. The higher the number, the greater the tensile strength. Figure 2. Grade Markings for U.S. Bolts and Hex Head Cap Screws Although there are many different grades of fasteners, some are more commonly used than others. Grade 3 fasteners should be used for nonmechanical applications that do not require high strength. Grade 5 fasteners, identified by three radial lines on their head, should be used where moderate strength is required. Grade 8 fasteners, identified by six equally spaced radial lines on their head, are required for critical applications such as flywheels, universal joints, transmission mounts and cases, motor supports, suspensions, and other high-load applications. The most common metric property classes are 8.8, 10.9, and A bolt with a lower tensile strength should never be used to replace a bolt with a higher strength. Remind your customers that all fasteners need to be properly tightened. They should refer to and follow the tightening instructions and specifications given by the vehicle s manufacturer. Over tightening and under tightening a bolt can cause it to fail. When a bolt is tightened, it stretches. This stretching provides clamping pressure. If the bolt is under tightened, the pieces that should be held together will be able to move. This can cause a bolt to break, become looser, or cause damage to the pieces. If a bolt is over tightened, the bolt will be stretched beyond its elastic limit. The elastic limit of a fastener is the maximum stress that can be applied to a fastener that will allow it to regain its original dimensions after it is removed. Once a bolt is over tightened, it is longer than it should be and must not be reused. Over tightening can also cause a bolt to break or damage the threads. NAPA FastTrack Counter Sales Training Fasteners Page 2
3 Nuts Nuts are internally threaded fasteners used with bolts or other externally threaded fasteners. The grade is marked on one of the flat sides of a nut. If no markings are present, the nut is a Grade 2. Nuts and bolts should be matched to not only the same grade, but also the same thread and diameter dimensions. The common types of nuts used on automobiles are the finished hex nut, prevailing torque lock nut, flanged lock nut, nylon insert lock nut, heavy hex nut, hex jam nut, acorn nut, and castellated nut (Figure 7). Figure 3. Common Types of Nuts Used on Automobiles Screws Screws (Figure 8) are headed, threaded fasteners that are either designed to turn into threaded holes or are designed to form their own threads as they are turned. This type of screw includes self-drilling screws, sheet metal screws, wood screws, and thread cutting screws. Screws used in threaded holes or nuts include cap screws, carriage screws, and machine screws. NAPA FastTrack Counter Sales Training Fasteners Page 3
4 Figure 4. Different Types of Screws Washers Washers are mainly used as a seat for bolts, nuts, and screws. They prevent damage to the head fillet as the bolt is being tightened. They also distribute the tightening load over a greater area than would be provided by the fastener s head. Washers also provide springlike tension between the fastener and the piece receiving the fastener. This helps to keep the bolt from loosening. Some washers, called lock washers, are specifically designed to prevent bolts, nuts, and screws from loosening. Washers can also be used to take up space or seal a bolt or nut. Figure 9 shows some of the common washers used in an automobile. Figure 5. Common Automotive Washers NAPA FastTrack Counter Sales Training Fasteners Page 4
5 Other Common Fasteners An automobile is held together by many other fasteners. You should be familiar with all of them. Figure 10 shows just a few of these. To learn more about these, refer to your Rockford catalog. Figure 6. Other Common Types of Automotive Fasteners NAPA FastTrack Counter Sales Training Fasteners Page 5
6 Thread Damage If a fastener has failed or broken, its mating piece must also be replaced or repaired. There are many ways to repair threads and your store sells the tools and equipment to do this. Extractors, tap and die sets, and Heli Coil-thread repair kits are the most commonly used. An extractor is used to remove a broken bolt from its hole. A tap is used to cut new internal threads, while a die cuts external threads. The Heli Coil-thread inserts new threads into a damaged hole. All of these tools can be found in the NAPA Tools and Equipment Catalog. Key Terms Bolt an externally threaded fastener designed to hold components together. Also called a cap screw. Bolt diameter the measurement across the major diameter of the threaded area. Bolt head used to tighten the bolt with a socket or wrench. Bolt shank the diameter of the threaded area of a bolt. Cap screw an externally threaded fastener designed to hold components together. Also called a bolt. Clamping force the amount of tension force that holds two or more pieces together when a fastener is tightened. Grade marks markings on the head of a bolt that indicate its tensile strength. Nuts internally threaded fasteners used with bolts or other externally threaded fasteners. Screws headed, threaded fasteners that are either designed to turn into threaded holes or are designed to make their own threads. Thread pitch in the English system is determined by the number of threads that are in one inch of threaded bolt length and is expressed in number of threads per inch. The thread pitch in the metric system is determined by the distance in millimeters between two adjacent threads. Washers inserts that are mainly used as a seat for nuts, bolts, and screws. NAPA FastTrack Counter Sales Training Fasteners Page 6
3400 E. WALNUT STREET COLMAR, PA DORMAN / ROCKFORD
WEATHERLY #770 D-2013-A JUNE 2013 SUPERSEDES R-2009-F APR. 2009 2013 DORMAN / ROCKFORD 1-800-523-2492 Corporate Office & Customer Service www.dormanproducts.com 2013 Dorman Products, Inc. No reproduction
More informationWhat is a fastener? A device to locate or hold parts
What is a fastener? A device to locate or hold parts As a repair technician you will become skilled at removing, reconditioning, replacing, and installing fasteners. An important skill to learn is how
More information1/2/2016. Lecture Slides. Screws, Fasteners, and the Design of Nonpermanent Joints. Reasons for Non-permanent Fasteners
Lecture Slides Screws, Fasteners, and the Design of Nonpermanent Joints Reasons for Non-permanent Fasteners Field assembly Disassembly Maintenance Adjustment 1 Introduction There are two distinct uses
More informationUNIT 9b: SCREW FASTENERS Introduction Functions Screw Features Elements Terms of a Thread Profile
UNIT 9b: SCREW FASTENERS Introduction A mechanical screw is a cylinder or cone that has a helical ridge called a thread. A helix has one or more turns, so a screw can have several turns. If the helix is
More informationMechanical joints. Major diameter Mean diameter Minor diameter Pitch p chamfer. Root Crest. Thread angle 2a. Dr. Salah Gasim Ahmed YIC 1
Screw fasteners Helical threads screws are an extremely important mechanical invention. It is the basis of power screws (which change angular motion to linear motion) and threaded fasteners such as bolts,
More informationChapter 7. Fasteners
Chapter 7 Fasteners LEARNING OBJECTIVES After studying this chapter, students will be able to: Identify several types of fasteners. Explain why inch-based fasteners are not interchangeable with metric-based
More informationBOLTS AND NUTS Square Bolts( Table 1 ) Hex Nuts ( Table 7 ) Heavy Hex Nuts (Table 7) Heavy Hex Structural Bolts ( Table 2 )
BOLTS AND NUTS 1493 An externally threaded fastener that must be assembled with a nut to perform its intended service is a bolt. (Example: heavy hex structural bolt.) An externally threaded fastener that
More informationFastener Type Chart. Fastener Categories. Sheet Metal Screws Fully threaded screws with a point for use in sheet metal. Abbreviated SMS.
Fastener Categories Wood Screws Machine Screws Thread Cutting Machine Screws Screws with a smooth shank and tapered point for use in wood. Abbreviated WS. Screws with threads for use with a nut or tapped
More informationAir Cooled Engine Technology. Roth 9 th Ch 3 Fasteners & Sealing Pages 45 65
Roth 9 th Ch 3 Fasteners & Sealing Pages 45 65 1. Engine & equipment can be common or can be designed to perform specific functions. Fasteners Options Features 2. The of a fastener is actually an inclined
More informationMETRIC FASTENERS 1520 METRIC FASTENERS
1520 METRIC FASTENERS METRIC FASTENERS A number of American National Standards covering metric bolts, screws, nuts, and washers have been established in cooperation with the Department of Defense in such
More informationCNC Router Parts. Standard Rack & Pinion Drive Assembly Instructions
CNC Router Parts Standard Rack & Pinion Drive Tools List The following tools will be used for assembly and installation of the Standard Rack & Pinion Drive: Imperial Allen Wrench Set - 3/32", 5/32", 3/16",
More informationFastener Basics. Common Fastener Types. Fastener Materials. Grade / Class and Fastener Strength
Fastener Basics Common Fastener Types Fastener Grade (US) or Class (metric) refers to the mechanical properties of the fastener material. Generally, a higher number indicates a stronger, more hardened
More informationFASTENERS, MEASUREMENTS AND CONVERSIONS
FASTENERS, MEASUREMENTS AND CONVERSIONS Bolts, Nuts and Other Threaded Retainers Although there are a great variety of fasteners found in the modern car or truck, the most commonly used retainer is the
More informationDRILL BITS & THREAD REPAIR DRILL BITS
DRILL BITS DRILL BITS Designed for drilling soft metal mild steel wood plastic and PVC Manufactured from industrial high speed steel surface treated for high performance and long life 29 piece set includes
More informationStudents have little or no previous knowledge or skill in the material being covered.
Youth Explore Trades Skills Description This Activity Plan will enable students to identify the differences between metric and imperial bolts (cap screws). They will learn how to measure a bolt and determine
More informationc. Pins, bolts, and retaining rings b. Washers, locking nuts, and rivets
62 20 HW 8: Fasteners / Force, Pressure, Density Mechanical Systems DUE Mon, 11/21/16 Start of class Check link on website for helpful fastener information Please use a scantron. Material is based primarily
More informationUNIVERSAL TOOLS. 572 Shop. Motion Pro T-Handle Socket Wrenches. Motion Pro Mini-Pro T-Handle Deep Socket Wrench
Motion Pro T-Handle Socket Wrenches Metric T-Handles feature a durable nickel pewter finish Deep 6-point sockets Lifetime replacement warranty DESCRIPTION TCI PART # RETAIL 8 mm Socket 722-8093 $ 17.95-J
More informationWhat is a fastener? A device to locate or hold parts
What is a fastener? A device to locate or hold parts As a repair technician you will become skilled at removing, reconditioning, replacing, and installing fasteners. An important skill to learn is how
More informationFasteners. Fastener. Chapter 18
Fasteners Chapter 18 Material taken from Mott, 2003, Machine Elements in Mechanical Design Fastener A fastener is any device used to connect or join two or more components. The most common are threaded
More informationSCREW THREADS. = minor diameter. d 3. d 2. = pitch diameter
ISO : 6 Part 2 DIN : Part /20 Metric (ISO) screw thread, coarse series -M- T-00 T-002 for M to incl. M,4, fit H/6h The bold lines indicate the maximum material profiles. The maximum material profile of
More informationTechnical Specifications Guide For Fasteners
fastrite_2011_fut.ai 8/4/11 4:29:01 PM Technical Specifications Guide For Fasteners C M Y CM MY CY CMY K Important Disclaimer All of the information provided in this publication is intended for reference
More informationBig Block Installation Manual For Systems without A/C
Big Block Installation Manual For Systems without A/C Billet Specialties, Inc. 500 Shawmut Ave. La Grange, IL 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 Hardware List For Chevrolet Big Block Tru
More informationFastener Basics. Common Fastener Types. Fastener Materials. Grade / Class and Fastener Strength
Fastener Basics Common Fastener Types Fastener Grade (US) or Class (metric) refers to the mechanical properties of the fastener material. Generally, a higher number indicates a stronger, more hardened
More informationCH # 8. Two rectangular metal pieces, the aim is to join them
CH # 8 Screws, Fasteners, and the Design of Non-permanent Joints Department of Mechanical Engineering King Saud University Two rectangular metal pieces, the aim is to join them How this can be done? Function
More informationE-Z LOK Products are available from MARYLAND METRICS P.O. Box 261 MD USA
E-Z LOK Products are available from MARYLAND METRICS P.O. Box 261 MD 21117 USA phones: (410)358-3130 (800)638-1830 faxes: (410)358-3142 (800)872-9329 web: http://mdmetric.com email: sales@mdmetric.com
More informationPage 1. SureMotion Quick-Start Guide: LARSACC_QS 1st Edition - Revision A 03/15/16. Standard Steel Bolt/Screw Torque Specifications
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LARSACC-013 LARSACC-014 LARSD2-08T12BP2C (12-in travel) LARSD2-08T24BP2C (24-in travel) C P I R K 1 ea Ball Screw with
More informationThreading - Hand Taps - Button Dies - Die Nuts - Screw Extractors - Holders - Sets THREADING
Threading - Hand Taps - Button Dies - Die Nuts - Screw Extractors - Holders - Sets THREADING Threading Threading Index 198 Dies Carbon, Button Dies BA 198 Dies Carbon, Button Dies BSB 197 Dies Carbon,
More informationThreading -Hand Taps -Button Dies -Die Nuts -Screw Extractors -Holders -Sets
Threading Threading -Hand Taps -Button Dies -Die Nuts -Screw Extractors -Holders -Sets Threading Threading Index 148 Threading Taps Carded 149 Threading Taps Bulk Metric 150 Threading Taps Bulk Metric
More informationBolts Carriage Elevator Eye Hex Shoulder Specials Square Head Step. Drills, Taps, & Bits. Hex Capscrews Grade 8 Grade 5 Grade 2 A325 A490 Specials
AU-VE-CO Bolts Carriage Elevator Eye Hex Shoulder Specials Square Head Step Concrete Anchoring Adhesives Anchor Bolts Drop Ins Wedge Pins Cotter Dowel Hitch Spring Roll Taper Pipe Fittings Power Coil EZ
More informationExtracts without expanding material Ideal for pipes and fittings Works on left-hand or right-hand threads
Serious Solutions for Stuck Fasteners IRWIN Tools has the solution to deal with a stuck fastener, a rounded or broken head, a snapped stud, or a stripped screw or fitting. Five different styles of extractors
More informationVARVIT USA, LLC SEQUOIA DRIVE SUITE 101 AURORA,ILLINOIS USA PRODUCT CATALOG
PRODUCT CATALOG With over 50 years of manufacturing experience, The Vescovini Group is one of the major players in the European market producing high quality fasteners, screws, nuts, studs, wheel bolts
More informationHandout Activity: HA043
Handout Activity: HA043 Student/Intern information: Name Date Class Summary There are many different fasteners used in automotive applications, including screws, bolts, studs & nuts. Washers & chemical
More informationFASTENERS. Aylin YENİLMEZ GÜRKÖK
FASTENERS Aylin YENİLMEZ GÜRKÖK FASTENERS A fastener is a hardware device that mechanically joins or affixes two or more objects together. Welding, Soldering, Nuts & Bolts, Washers, Screws, Clips, Clamps,
More informationPPM-5710 JK HEAVY DUTY SKID PLATE ASSEMBLY Version 2.0
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 PPM-5710 JK HEAVY DUTY SKID PLATE ASSEMBLY Version 2.0 GENERAL NOTES: These instructions are also available on our website; www.synergymfg.com.
More informationOperation Manual Panel Mounting Gas Pressure Regulators
687 Technology Way Napa, CA 94558 Phone: (707) 259-0102 FAX: (707) 259-0117 www.aptech-online.com Table of Contents: A. General information... 1 B. Panel Mount Nut - AP/AZ/AK/SL Model Regulators... 1 C.
More informationThread Repair & Thread Protection
Thread Repair & Thread Protection Screw Thread Inserts, Kits & Components for Industrial Maintenance, Repair and Overhaul Bulletin 998 C E R T I F I E D ISO 9001 AS 9100 TS 16949 ISO 14001 The HELI-COIL
More informationAN, MS, NAS Bolts. AN3 20 bolts are identified by a multi-part code:
AN, MS, NAS Bolts Most bolts used in aircraft structures are either (a) general-purpose, (b) internal-wrenching or (c) close-tolerance AN, NAS, or MS bolts. Design specifications are available in MIL-HDBK-5,
More informationTAP AND DRILL BIT SELECTION GUIDE TAPS AND DIES. NATIONAL STANDARD THREADS Imperial (NC, NF, NS, UNC and UNF)
TAP AND DRILL BIT SELECTION GUIDE NATIONAL STANDARD THREADS Imperial (NC, NF, NS, UNC and UNF) THREAD NOMINAL SIZE THREAD STANDARD DRILL SIZE* DECIMAL 0 80 NF 3/64".0469" 1 64 NC 53.0595" 1 72 NF 53.0595"
More informationChain Drive Vise. Installation Instructions. (revised 05/04/2016)
Chain Drive Vise Installation Instructions (revised 05/04/2016) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition
INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E) ISO 2005 PDF disclaimer This
More informationFluid Sealing Association
Fluid Sealing Association STANDARD FSA-MG-501-02 STANDARD TEST METHOD FOR INWARD BUCKLING OF SPIRAL-WOUND GASKETS 994 Old Eagle School Road, Suite 1019 Wayne, Pennsylvania 19087-1866 Phone: (610) 971-4850
More informationMechanical Systems & Tools Syllabus [Detailed]
TECHNICAL TRAINING - SWAPPING DOWNTIME FOR PRODUCTIVITY! Mechanical Systems & Tools Syllabus [Detailed] Your automation.ie Fact Sheets! Understand Mechanical Energy Types! 1 Staying Safe in the Mechanical
More informationAIRCRAFT HARDWARE What You Need To Know By Ron Alexander
Page 1 of 6 AIRCRAFT CONSTRUCTION An Article Series by Ron Alexander AIRCRAFT HARDWARE What You Need To Know By Ron Alexander The quality of our workmanship in building an airplane is very important. We
More informationMetals can be bought from suppliers in standardized forms and sizes, such as round,
1.4 METAL CUTTING BAND SAWS: Metals can be bought from suppliers in standardized forms and sizes, such as round, rectangular or square bar stock or in the form of large sheets (plates). Bar stock normally
More informationFastener Handout. Introduction: Engineering Design Representation 2. Threads 2. Local Notes (callouts) 8. Threaded Mechanical Fasteners 13
Fastener Handout Introduction: Engineering Design Representation 2 Threads 2 Effect of thread angle on strength: 3 Standardization of Threads: 4 Descriptions of the Thread Series: 4 Class fit: 5 Specification
More informationAN, MS, NAS Bolts. AN3 20 bolts are identified by a multi-part code:
AN, MS, NAS Bolts Most bolts used in aircraft structures are either (a) general-purpose, (b) internal-wrenching or (c) close-tolerance AN, NAS, or MS bolts. Design specifications are available in MIL-HDBK-5,
More informationLOCTITE WEBINAR SERIES Threadlocking & the Torque-Tension Relationship
LOCTITE WEBINAR SERIES Threadlocking & the Torque-Tension Relationship Meet Your Presenters Doug Lescarbeau Michael Feeney Market Development Director Doug.Lescarbeau@Henkel.co m Application Engineer Michael.Feeney@Henkel.com
More information9/8/98 AC B CAUTION THE FOLLOWING TORQUE VALUES ARE DERIVED FROM OIL FREE CADMIUM PLATED THREADS.
TABLE 7-1. Recommended torque values (inch-pounds). CAUTION THE FOLLOWING TORQUE VALUES ARE DERIVED FROM OIL FREE CADMIUM PLATED THREADS. TORQUE LIMITS RECOMMENDED FOR INSTAL- LATION (BOLTS LOADED PRIMARILY
More informationObsolete fastener specialist
Obsolete fastener specialist CLASSIC FASTENERS was established circa 1988 to supply 'obsolete' and just plain hard to get fasteners to restorers of automobiles and motorcycles via a mail order service.
More informationSR-1.0 Manual, a.doc 11/14/2006 Page 1 of 17
SR-1.0 Manual, 20061108a.doc 11/14/2006 Page 1 of 17 ASSEMBLY INSTRUCTIONS, MODEL SR-1.0 EXTRUSION HEAD STREAMLINE EXTRUSION, INC. Following is a set of photos and verbal descriptions for assembling the
More informationUSER MANUAL Nord-Lock X-series washers
USER MANUAL Nord-Lock X-series washers JOINT GUIDE 3 ASSEMBLY INSTRUCTIONS 4 TECHNICAL DATA 5 TORQUE GUIDE 5 THE EXCEPTIONAL SYSTEM THAT PREVENTS BOLT LOOSENING AND SLACKENING Nord-Lock X-series washers
More informationMAG-CONV Basic, 48, 48R & Midline Front Mount
Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total
More informationMECHANICAL ASSEMBLY John Wiley & Sons, Inc. M. P. Groover, Fundamentals of Modern Manufacturing 2/e
MECHANICAL ASSEMBLY Threaded Fasteners Rivets and Eyelets Assembly Methods Based on Interference Fits Other Mechanical Fastening Methods Molding Inserts and Integral Fasteners Design for Assembly Mechanical
More informationISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition
Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E)
More informationEngineering Design Representation. Use of 2D drawing format: Typical Design Annotation. Standardization. Extracted drawings. General dimensions
Engineering Design Representation Some elements of design representation not easily conveyed through model alone. Many are notational in nature. Examples are: Thread specifications Surface finishes Surface
More informationIDR assembly instructions:
IDR assembly instructions: Required Tools: 2 X 12mm Open End Wrench 14mm open end wrench #2 Phillips Head Screw Driver (Drill with adjustable torque clutch recommended) 8mm nut driver (Supplied in IDR-AK)
More informationChain Drive Vise. Installation Instructions. (revised 11/29/2018)
Chain Drive Vise Installation Instructions (revised 11/29/2018) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationCSS Central Mount System
CSS-20 Installation Manual CSS-20 Safety Notifications Below are the installation instructions for the CSS-20-2 Long Span Beam Mounting System. Please read these safety notifications prior to beginning
More informationUnit 047: Advanced Turning. Screw threads
Unit 047: Advanced Turning Screw threads Starter activity When was the screw thread invented? Who was the inventor of the most famous screw thread form? When was the first unified British thread invented
More informationFNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson.
FASTENERS PIPE HANGERS, SUPPORTS & STRUT ACCESSORIES FNW can handle all your hanger and fastener needs, all in one place. FNW products are sold exclusively at Ferguson. Quick Reference Nuts Heavy Hex Nuts...4
More information01 FASTENERS JULY FASTENERS 1
01 FASTENERS 4 Bolts 22 Socket Screws 30 Nuts 39 Washers 53 Screws 72 Threaded Rods & Studs 73 Rivets, Rivnuts & Accessories 82 Retaining Rings 84 Pins, Links, & Sleeves 91 Key Stock & Assortments 90 Anchors
More informationDRAWER Mitsubishi pajero lwb
DRAWER Mitsubishi pajero lwb SSDS601 / SSMP001 INSTALL TIME: 45 mins Thank you for purchasing a Front Runner Storage System. This Storage System is made up of the following components: 1. A Drawer System
More informationInstallation Instructions: Bumper (Part # SB76850) XJ Jeep Cherokee XRC Rear Bumper
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty 93-7789 XJ XRC 1 93-7807 Bumper Mount Bracket: Drvr 1 93-7811 Bumper Mount Bracket: Pass 1
More informationAll Terrain Flares 2014 Chevy Silverado
Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -
More informationERECTION & CONSTRUCTION
ERECTION & CONSTRUCTION High Strength Structural Bolting Author: Clark Hyland Affiliation: Steel Construction New Zealand Inc. Date: 24 th August 2007 Ref.: Key Words High Strength Bolts; Property Class
More informationInstallation Type. Edge of Door. Pull (Hinge) Side Mounted. Hinge Edge of Door. Push (Stop) Side Mounted
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationCOMMON WRENCHES INTRODUCTION
COMMON WRENCHES INTRODUCTION A wrench is a hand tool used to provide grip and mechanical advantage in applying torque to turn objects usually nuts and bolts. Wrenches allow us to use less force to rotate
More informationThis manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.
This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4
More informationThreading -Hand Taps -Button Dies -Die Nuts -Screw Extractors -Holders -Sets
THREADING Threading -Hand Taps -Button Dies -Die Nuts -Screw Extractors -Holders -Sets Threading Index Hand Taps - Carded Metric Coarse UNF BSW 93 93 93 Hand Taps - Bulk Metric Coarse Metric Fine Metric
More informationDEPTH-KIT-785 Seat Depth Extension
Parts Required: 2 x Seat Frame Plugs 1.5 or 3 1 x Elevation Rod 18.5 or 20 2 x Attachment Rods 18.5 or 20 3 x Vinyl Straps color and width specific Tools Used: Sissors 2 x ½ Wrench Soft Tip Hammer or Mallet
More informationThe Ensat self-tapping threaded insert...
The nsat self-tapping threaded insert... nsat is a self-tapping threaded insert with external and internal thread, cutting slots or cutting bores. A continuous process of further development has brought
More informationInstallation Instructions
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationFasteners Table of Contents
EML2322L Design & Manufacturing Laboratory Fasteners Table of Contents I. Copyright Notice II. Why Care? 1. Definitions 2. Common Fastener Types 3. Fastener Nomenclature 4. Fastener Thread Types 5. Rolled
More informationObsolete fastener specialist
Obsolete fastener specialist CLASSIC FASTENERS was established circa 1988 to supply 'obsolete' and just plain hard to get fasteners to restorers of automobiles and motorcycles via a mail order service.
More informationThread and Connector Identification
How to Use this Section This section is intended as an aid to identifying the most popular threads on hydraulic hose couplings and adaptors, and hydraulic equipment. BSP, Metric, American and Japanese
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationINSIDE PANEL NOT SHOWN TO DETAIL ANCHORING SYSTEM
SIX INCH ALPHA MODULE INSTALLATION KEWAUNEE SCIENTIFIC CORPORATION SIX INCH ALPHA MODULE ANCHORING SYSTEM After Alpha module has been set in desired location. Adjust the four adjustment bolts until the
More informationAUDAS. Tel: Fax: No.259 Baichi north Rd.Haiyan.Zhejiang.
Standard State SECTION A : SCREW THREAD Basic elements of screw thread design ANSI/ASME B1.7M Nomenclature.Definitions and letter symbols for screw thread ASME B1.1 Unified inch screw thread ( UN and UNF
More informationSECTION 7. SAFETYING
9/8/98 AC 43.13-1B SECTION 7. SAFETYING 7-122. GENERAL. The word safetying is a term universally used in the aircraft industry. Briefly, safetying is defined as: Securing by various means any nut, bolt,
More informationBolts and Set Screws Are they interchangeable?
1903191HA Bolts and Set Screws Are they interchangeable? Prof. Saman Fernando Centre for Sustainable Infrastructure SUT Introduction: This technical note discusses the definitions, standards and variations
More informationTable of Contents. GARD Specialists Co., Inc. GARD Specialists Co., Inc. P.O. Box 157 Eagle River, WI Fax
Table of Contents Heavy Duty Fasteners F-911 Fasteners Introduction... 2 F-911 Fasteners Specifications... 2 F-911 Fasteners Torque Chart... 3 Cap Screws - F-911 Alloy Hex Head, Coarse... 4-9 Assortments,
More informationBy Bob Lacivita as seen in the September 2002 issue of CBR (Classic Bike. In my 35 years as a master automotive technician, instructor of automotive
Awww Nuts (and Other Fasteners) By Bob Lacivita as seen in the September 2002 issue of CBR (Classic Bike Rider Magazine). In my 35 years as a master automotive technician, instructor of automotive technology,
More informationPAK Drum Roll Top Assembly Instructions. Note: 2 people will be required to assemble roll top
PAK901 4 Drum Roll Top Assembly Instructions Note: 2 people will be required to assemble roll top PLEASE READ ASSEMBLY INSTRUCTIONS CARFULLY Tools required: 5/8 Socket & Ratchet 9/16 Deep Well Socket &
More informationIN 578. Tools Required. Torque Specification: 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench.
Tools Required 2011-C Ford F250/F350 No Drilling into Vehicle is Required 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench FL277 x 1 Torque Specification: 1/4 Bolts - 6 Ft Lbs.
More informationINSTRUCTIONS
IMPORTANT: THIS IS A HIGH PERFORMANCE PART AND IMPROPER INSTALLATION COULD RESULT IN INJURY OR DEATH! NEVER WORK UNDER AN AUTOMOBILE THAT IS NOT PROPERLY SUPPORTED AND BLOCKED FROM ROLLING. NO CREDIT OR
More informationEnsat driving tools...
nsat driving tools... On this page, you can configure the optimum tool for your application. A configuration is provided in the following as an illustrative example. The article number is composed of two
More informationTAPPING SCREWS 1-1 TAPPING SCREWS PHILLIPS OVAL. 1 General Fasteners HEAD ZINC BLACK SIZE SIZE CHROME CHROMATE OXIDE
TAPPING SCREWS TAPPING SCREWS PHILLIPS OVAL HEAD ZINC BLACK SIZE SIZE CHROME CHROMATE OXIDE #4 x 3/8"... REG... 110001 #4 x 1/2"... REG... 105030... 110002 #4 x 5/8"... REG... 1 10003 #4 x 3/4"... REG...
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all
More informationFlooring Nails 6-D Flooring Nails $3.40 / 1# 6-D Flooring Nails $14.50 / 5# 8-D Flooring Nails $3.40 / 1# 8-D Flooring Nails $14.
Nails Nails Drywall Screws Common Nails 4D Common Nails $3.85 / 1# 6D Common Nails $3.00 / 1# 6D Common Nails $74.25 / 50# 8D Common Nails $3.00 / 1# 8D Common Nails $74.25 / 50# 10D Common Nails $3.00
More informationComparable ISO Standard. Date of current standard/modified
Title Standard All-metal prevailing torque All-metal prevailing torque EN ISO EN ISO Comparable ISO Standard Date of current standard/modified 980 7042 27042 7042 1998-02 980 10513 30513 10513 1998-02
More informationHEICO-LOCK WEDGE LOCK WASHERS
HEICO-LOCK WEDGE LOCK WASHERS WEDGE LOCK WASHERS The Heico-Lock wedge locking system delivers high quality anti-vibration security for the most demanding of bolted joint applications. Even under extremes
More informationUNIVERSITY OF THESSALY
UNIVERSITY OF THESSALY MECHANICAL ENGINEERING DEPARTMENT Instructor: Dr. S.D. Chouliara e-mail: schoul@uth.gr MACHINE ELEMENTS Task 2 1. Let the bolt in the following Figure be made from cold-drawn steel.
More informationDynaPower Generation II
DynaPower Generation II Return to DYNAPOWER index Return to MAIN index GENERATION II 2.0 DYNAPOWER MODEL 2.0 VARIABLE PUMP PARTS DRAWING GENERATION II 2.0 DYNAPOWER MODEL 2.0 VARIABLE PUMP PARTS DRAWING
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationCHAPTER 4. Jones & Bartlett Learning, LLC NOT FOR SALE OR DISTRIBUTION. Jones & Bartlett Learning, LL NOT FOR SALE OR DISTRIBUT
CHAPTER 4.. Identifying Locking Devices 4 Primary Learning Objectives FOR After reading OR DISTRIBUTION this chapter, you will be able to: 1. Identify types of threads, nuts and bolts. (pp. 109 111, 113)
More informationSwivel Hoist Ring Page 142
Swivel Hoist Ring Page 142 Hoist Rings Color coded to distinguish between UNC (Red) and Metric (Silver) thread types HR-125 M HR-125 Available in UNC and Metric thread sizes. UNC threads available in sizes
More informationGAGING AND INSPECTION
Fixture Plates...75 Fixturing Towers...76 CMM Fixturing Kits... 77-78 Clamping Components... 79-80 Standoffs and Locators... 81-82 Magnetic Components... 83-84 Height Adjustment...84 Positioners...85 Clamp
More informationInstallation Instructions Kit, Base Rail Bracket Part # 31413
Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating and
More information