BEARING UPGRADE INSTRUCTIONS FOR

Size: px
Start display at page:

Download "BEARING UPGRADE INSTRUCTIONS FOR"

Transcription

1 BEARING UPGRADE INSTRUCTIONS FOR RECOMMENDED TOOLS AND SUPPPLIES: Enduro Outboard Bearing Kit (chromium steel or ceramid hybrid) Enduro Outboard Bearing Puller/Press Tool Enduro Outboard Cup Removal Tool Ratchet Wrench w/ 1/2 Drive 8mm Allen Wrench Rock n Roll Super Web Grease Rubber-faced mallet Strap Wrench or Soft-Jawed Vise 2006 Real World Cycling/enduroforkseals.com

2 1) For the GXP system, be sure you have the latest version of the Puller/Press, which includes a special bearing shim extractor/installer (pictured at right). Remove your chain before beginning... 2) Use an 8mm Allen wrench to extract the non-drive side crank arm Real World Cycling/enduroforkseals.com

3 3) Use a rubber-faced mallet to start the axle moving toward the drive side. 4) Remove the right crank assembly Real World Cycling/enduroforkseals.com

4 5) Use the Enduro Outboard Cup Removal Tool to loosen the non-drive bearing cup. This side has standard threads, so loosen by turning it counter-clockwise. The axle sleeve may or may not come out with the cup. If it does, pull it out of the cup and set the sleeve aside. Be sure and take note of any spacers, so that they can be reinstalled as required Real World Cycling/enduroforkseals.com

5 6) Remove the OE spacer/seal from the non-drive cup. WE WILL NOT BE RE- USING THIS SEAL. 7) Take the cup holder portion of the Puller/ Press Tool and set it upside down ( Enduro facing up) on a flat surface Real World Cycling/enduroforkseals.com

6 8) Place the outboard cup on top of the cup holder with the bearing facing up. 9) Insert the GXP shim extractor into the shim as shown. 10) Insert and hand-tighten the bolt. 11) Tighten the bolt using the 8mm Allen wrench until the extractor bottoms out against the bearing. At this point, the bearing shim will have been pushed completely out of the bearing. Remove the bolt Real World Cycling/enduroforkseals.com

7 12) You will find the reducing shim sitting on top of the cup holder. SET THIS SPACER ASIDE AS YOU WILL NEED TO USE IT WITH THE NEW BEARING. 13) Push the expander into the collet as shown Real World Cycling/enduroforkseals.com

8 14) Place the outboard cup into the open side of the cup holder with the bearing facing down. 15) Insert the expander and collet into the center of cup. The flanges of the collet with catch on the back of the bearing. 16) Insert the bolt through the expander and thread it into the cup holder by hand Real World Cycling/enduroforkseals.com

9 17) Use the 8mm Allen wrench to tighten the bolt and press the bearing out. Note that TruVativ likes to really glue these bearings in. If you have trouble keeping the cup holder from turning in your hand, you can use a strap wrench (see step 36) or pad the jaws of a vise and apply just enough pressure to hold it in place (DO NOT DISTORT THE CUP HOLDER BY OVER-TIGHTEN- ING THE VISE). 18) Remove the bearing cup and clean out any residual glue or grease. 19) Get a new bearing from your Enduro Kit Real World Cycling/enduroforkseals.com

10 20) Start the OE bearing reducer shim into the new Enduro bearing by hand. It won t go in far--just get it to start evenly. 21) Place the bearing, shimside down, on the BACK of the Enduro cup holder. 22) Insert the shim press through the bearing and inside of the shim, as shown. 23) Place the bearing support on top of the shim installer, recess down, as shown Real World Cycling/enduroforkseals.com

11 24) Fully seat the shim by inserting the bolt through the support and shim installer and using the 8mm Allen wrench to tighten the bolt until the shim is fully seated. A fully seated shim will be bottomed out on the flange side and will extend about 1mm past the inner race of the bearing on the other side.

12 25) Place the empty non-drive side outboard cup into the cup holder with the threads facing down. 26) Place the new bearing (now with the shim pressed into it) into the outboard cup with the flange side of the reducer facing down.

13 27) Place the support on top of the bearing as shown. When oriented correctly, the reducing shim of the bearing will fit up into the recess of the support. This keeps the shim from getting pushed back out. 28) Insert the bolt, threading it into the cup holder by hand. Then, fully tighten with the 8mm Allen wrench to seat the new bearing into the outboard cup.

14 Note that the bearing is fully seated in the cup and the bearing shim still extends about 1mm past the inner race of the bearing. It is now ready to be installed into the frame. 29) Apply some grease to the cup threads and reinstall the cup (and any required cup spacers) into the non-drive side of the bottom bracket shell. Thread clockwise to tighten. WE WILL NOW TURN OUR ATTEN- TION TO THE DRIVE SIDE BEARING CUP.

15 30) Use the Enduro Outboard Cup Removal Tool to remove the drive side cup. Remember that the drive side is reverse-threaded, so turn clockwise to loosen. 31) As you remove the cup, take note of any spacers so that they can be re-installed as required.

16 32) Remove the OE spacer/ seal from the cup. We will not be re-using this seal. 33) Place the outboard cup into the open side of the cup holder with the bearing facing down. 34) Insert the expander and collet into the center of cup. The flanges of the collet with catch on the back of the bearing.

17 35) Place the bolt through the collet expander and thread it into the cup holder. Use the 8mm Allen wrench to tighten the bolt and press the bearing out. 36) Because TruVativ uses a rather strong adhesive to retain the bearings, the additional leverage provided by a strap wrench or softjawed vise may be required. You may even hear an audible crack when the bearing lets loose...

18 37) Clean the outboard cup as needed to remove residual adhesive or grease. 38) Take the other bearing out of the kit and place it on the 24mm side of the bearing guide.

19 39) Place the bearing and bearing guide into the cup holder. 40) Place the open side of the outboard cup on top of the bearing.

20 41) Place the support on top of the outboard cup with the extention side of the support inserted into the bearing cup. 42) Insert the bolt and fully tighten with the 8mm Allen wrench. Note that the bearing will not be fully seated into the cup at this stage. 43) Remove the outboard cup and the bearing guide part of the tool from the cup holder.

21 44) Put the outboard cup back into the cup holder with the threads facing down. 45) Place the support on top of the new bearing (as pictured at right) and install the bolt by hand. 46) Tighten the bolt with the 8mm Allen wrench to fully seat the bearing.

22 47) Re-install the drive side outboard cup into the bottom bracket shell. Use grease or anti-seize compound on the cup threads. If you did not install the sleeve with the non-drive side cup, remember to install it now! Also, be sure that any spacers previously used between the cup and frame are not forgotten. 48) Use the outboard cup tool to tighten the drive side outboard cup (turn counterclockwise to tighten). Proper torque vaue is: Foot Pounds = Inch Pounds =34-41 Newton-meters = Kg-force cm

23 49) Take the orange silicone spacer/seal from the Enduro bearing kit. 50) Slide the seal onto the axle with the metal side of the seal facing toward the bearing. 51) Apply a generous coat of Super Web Grease on the metal side of the seal.

24 52) Start the axle into the drive side cup and bearing. 53) As you push the axle in, the seal will take its place inside the cup. 54) Center the axle and push it until the splined end comes through the other side and it bottoms out.

25 By way of explanation, the axle bottoms out when the step in the axle contacts the bearing reducing shim. The cup, sleeve, and seals are omitted from the pictures below for clarity. Axle Step Axle Step contacting the bearing shim

26 55) Place the special metal shim from the Enduro Kit over the end of the axle and up against the bearing. 56) Take the black spacer/seal from the Enduro Kit and apply a coat of grease on the metal side. Slide the seal onto the axle with the black silicone side facing out. 57) Properly align the nondrive crank arm and slide it onto the splines of the axle.

27 58) Use the 8mm Allen wrench to tighten the non-drive crank arm. After fully tightening, give that crank arm a spin and see how smooth your crankset was meant to be! Torque Values for the Crank Arm Bolt: Foot Pounds = Inch Pounds =48-54 Newton-meters = Kg-force cm

INSTRUCTION GUIDE S-WORKS MTN CARBON CRANKSET (Press-in and Standard OSBB cups)

INSTRUCTION GUIDE S-WORKS MTN CARBON CRANKSET (Press-in and Standard OSBB cups) INSTRUCTION GUIDE S-WORKS MTN CARBON CRANKSET (Press-in and Standard OSBB cups) THIS BRIEF INSTRUCTION GUIDE CONTAINS IMPORTANT INFORMATION. PLEASE READ CAREFULLY AND STORE IN A SAFE PLACE. Congratulations!

More information

Lightning Carbon Cranks/BB Installation Procedure

Lightning Carbon Cranks/BB Installation Procedure Lightning Carbon Cranks/BB Installation Procedure Thank you for selecting the highest performance carbon crank/bb assembly on the planet! To maximize your enjoyment and operation of your Lightning carbon

More information

Bearing Overhaul Instructions for: Tallboy (.1) 2009

Bearing Overhaul Instructions for: Tallboy (.1) 2009 Bearing Overhaul Instructions for: Tallboy (.1) 2009 Tools Needed: 7900 Removal Tool 7902 Removal Tool 7900/7902/6902 Press Tool Grease Gun (included with frame) (2) ll/16" or adjustable wrenches 9/16"

More information

#4500 BULLET SIZER & LUBRICATOR

#4500 BULLET SIZER & LUBRICATOR #4500 BULLET SIZER & LUBRICATOR Assembly Your new #4500 Bullet Sizer and Lubricator has been fully assembled at the factory, However, to facilitate packaging and shipping, the handle has been dismounted.

More information

STYLE BAR & TONNEAU COVER INSTALLATION

STYLE BAR & TONNEAU COVER INSTALLATION STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT

More information

Installation Instructions

Installation Instructions The IMS ETERNAL FIX PATENT PENDING Installation Instructions EPS recommends professional installation for the Eternal IMS Fix. Please take all precautionary safety measures. We also recommend putting the

More information

White Industries Front Hub Instructions

White Industries Front Hub Instructions White Industries Front Hub Instructions Tools required: 2mm hex/allen wrench, set of sockets, mallet, bearing puller, bearing press. Disassembly 1. Loosen the set screws, there are three or one depending

More information

Cam Handle Service Guide

Cam Handle Service Guide Cam Handle Service Guide Page 2. Introduction Page 3. Troubleshooting guide Page 4-5. Adjusting the clamp force Page 6-7. Disassembling, greasing and replacing components Page 8-9. Replacing the post bearings

More information

Kogel Badass Bottom Brackets Installation manual

Kogel Badass Bottom Brackets Installation manual Kogel Badass Bottom Brackets Installation manual In this document we will explain the installation procedures for all Kogel bottom brackets. It is most important to know that installing bearings requires

More information

Installation instructions for FC9 & FC18 Forward Controls for Yamaha V-Max

Installation instructions for FC9 & FC18 Forward Controls for Yamaha V-Max Installation instructions for FC9 & FC18 Forward Controls for 1985-2007 Yamaha V-Max It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from

More information

Ford Pick Up Rear leaf Spring Kit Installation Instructions

Ford Pick Up Rear leaf Spring Kit Installation Instructions 1948-1956 Ford Pick Up Rear leaf Spring Kit Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Parts 48 inch leaf (2) springs (4) U-bolts 3/8-24 x l 1/4bolts (16) & nuts (2) 1/2-20 x 4

More information

Replacing the Reciprocator on an SWF Multi-head.

Replacing the Reciprocator on an SWF Multi-head. Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the

More information

Bearing Overhaul Instructions for: Nickel (0.1) and Butcher (0.1) a) Using a 6mm Allen wrench, remove the two bolts attaching the shock.

Bearing Overhaul Instructions for: Nickel (0.1) and Butcher (0.1) a) Using a 6mm Allen wrench, remove the two bolts attaching the shock. Bearing Overhaul Instructions for: Nickel (0.1) and Butcher (0.1) 2010 Tools Needed: 6902/7902/7900 Press Tool 6902 Removal Tool 7902 Bearing Removal Tool 7900 Removal Tool (2) ll/16" or adjustable wrenches

More information

Castle Frame Assembly Table AT-8. Diagnostics Manual. Castle, Inc. Petaluma, CA

Castle Frame Assembly Table AT-8. Diagnostics Manual. Castle, Inc. Petaluma, CA Castle Frame Assembly Table AT-8 Diagnostics Manual Castle, Inc. Petaluma, CA 800-282-8338 Solutions Index Adjusting the Tabletop.. 8.01 Adjusting the Fence... 8.02 Aligning the Arm... 8.10 Adjusting Bracket..

More information

Maintenance & Parts list for:

Maintenance & Parts list for: Maintenance & Parts list for: Industrial gun GB 2 Juni 2017 This Maintenance & Parts list for industrial gun is prepared by : Winchester Europe Service V. Parbst & Søn as a comprehensive maintenance guide

More information

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades OPERATIONAL MANUAL V1.0 BLUEROCK WS-212 Wire Stripper Removing/Replacing Blades CAUTION!! IMPORTANT!! DANGER!! WARNING!! DISCONNECT MACHINE FROM POWER BEFORE PROCEEDING!! Estimated Completion Time: 90

More information

Page 1. SureMotion Quick-Start Guide: LARSACC_QS 1st Edition - Revision A 03/15/16. Standard Steel Bolt/Screw Torque Specifications

Page 1. SureMotion Quick-Start Guide: LARSACC_QS 1st Edition - Revision A 03/15/16. Standard Steel Bolt/Screw Torque Specifications R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LARSACC-013 LARSACC-014 LARSD2-08T12BP2C (12-in travel) LARSD2-08T24BP2C (24-in travel) C P I R K 1 ea Ball Screw with

More information

HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions 1

HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions 1 HQ Pole Upgrade Kit for HQ Adjustable Table and HQ QuilTable Assembly Instructions QF09775 The pole upgrade kit can be used with or without the QF09700 HQ Precison-Glide track upgrade kit. What s Included

More information

HDL(M)6 Nut/Screw Assembly

HDL(M)6 Nut/Screw Assembly HDL(M)6 Nut/Screw Assembly Remove, repair, and reassemble the nut and screw assembly in your HDL series double lock vise. In these instructions when we refer to the front of the vise or nut/screw assembly,

More information

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16 Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete

More information

Installation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual

Installation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual Installation Guide for Rough Country 1.25 inch Body Lift Kit w/o Shocks (07-15 Wrangler JK 4 Door) Item # J10048 Option B; Manual Installation Time: 3 Hours Tools Required: Jack (Tall enough to reach body

More information

RIPPER PEDAL. Bearing / Axle Replacement. ( Disassembly )

RIPPER PEDAL. Bearing / Axle Replacement. ( Disassembly ) RIPPER PEDAL Bearing / Axle Replacement ( Disassembly ) 1 1. Use good quality tools to avoid stripping screw sockets. 2. When servicing your pedals, work on one side at a time to prevent parts from mixing

More information

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C) Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the

More information

Arc Trainer Main Frame Assembly

Arc Trainer Main Frame Assembly Arc Trainer Main Frame Assembly Kit No. 610AK019-4 Kit No. 630AK019-4 NOTE: This instruction sheet describes how to replace the main frame assembly in the Arc Trainer 610A. Tools Required 3/16 Allen wrench

More information

German Auto Solutions BMW Monoball Kit Installation DIY

German Auto Solutions BMW Monoball Kit Installation DIY Home Store Tool Rental BMW Products DIY Instructions Engine Services Dyno Services Machining Contact About German Auto Solutions BMW Monoball Kit Installation DIY BMW E39-E60-E90 G.A.S. Monoballs Installation

More information

BOW-A-CONSTRICTOR BUCKEYE ARCHERY SOLUTIONS

BOW-A-CONSTRICTOR BUCKEYE ARCHERY SOLUTIONS BOW-A-CONSTRICTOR BUCKEYE ARCHERY SOLUTIONS User Guide: Bow-A-Constrictor Tuning Station Note: The following instructions begin with the power bar tongue set at approximately the 6th hole from the crank.

More information

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems with A/C #13600 / #13620

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems with A/C #13600 / #13620 Small Block Ford 289 / 302 / 351W / 5.0 Installation Manual For Systems with A/C #13600 / #13620 Billet Specialties, Inc. 500 Shawmut Avenue. La Grange, Illinois 60526 Tech Line (708) 588-0505 Fax (708)

More information

Electric Skein Winder

Electric Skein Winder Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers

More information

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO 47(5x) 46 45 00 44 0 59 43 42 84 51 57 46 47 48 59 83 64 77 48 47(2x) 49(2x) 40 58 See service note on page 5 41 82 51 40 41 42 43 44 45 87 52 27 28 34 57 29 (6x) 60 28 EXAMPLE: Component Parts (Small

More information

08+ KAWASAKI KLR PD NERF

08+ KAWASAKI KLR PD NERF 08+ KAWASAKI KLR PD NERF 0505-1299 Before you begin, place the bike on a hard level surface where you have room to work. Lay out the parts included in this kit and compare to the parts list on page 5 of

More information

INSTRUCTIONS 360 CHAINROLL

INSTRUCTIONS 360 CHAINROLL INSTRUCTIONS 360 CHAINROLL 360 CHAINROLL REGISTRATION Please visit productregistration.360yieldcenter.com to complete the product registration for your 360 CHAINROLL so we can better support our products

More information

TRAILMATE METEOR ASSEMBLY MANUAL

TRAILMATE METEOR ASSEMBLY MANUAL TRAILMATE METEOR ASSEMBLY MANUAL The Trailmate Meteor recumbent has been designed for easy assembly. This means more time to enjoy the smooth ride with single speed, 3 speed coaster brake and 21 speed

More information

INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT

INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT BACKGROUND Proper alignment of the transmission input shaft to the crankshaft centerline is required in order to achieve the best results

More information

feltbicycles.com Bayonet 3 Manual

feltbicycles.com Bayonet 3 Manual Bayonet 2 Parts List: Bayonet 3 Parts List: 1. 3. 4. 5. 13. 14. M6 X 30mm Bolts Stem Extension M6 X 30mm Bolt (Knuckle) Knuckle Side Cap Set Screw Stem Base/Top Crown Splined Shaft/Knuckle M6 X 18mm Bolt

More information

`48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line:

`48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line: `48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line: 1-855-693-1259 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLING THE KIT.

More information

Pickup Box Utility Rack Package Installation (Instruction ID: )

Pickup Box Utility Rack Package Installation (Instruction ID: ) 017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation

More information

FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS

FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.

More information

INSTALLATION GUIDE Rear Bumper. Jeep JL Wrangler

INSTALLATION GUIDE Rear Bumper. Jeep JL Wrangler INSTALLATION GUIDE Rear Bumper Jeep JL Wrangler Dual Swing System 1A From the stock bumper you removed from vehicle, you ll need to take the parking sensor wiring from it and feed it into the new bumper.

More information

REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP

REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP REPLACEMENT TARP for SRT-2 SPOOL ROLL TARP NOTICE TO INSTALLER: Even if familiar with product, read instructions prior to installation as improvements may be made without notice. Always handle components

More information

SLED Frame Service Guide

SLED Frame Service Guide SLED Frame Service Guide Tools Needed: 10, 8, 6, 5 & 3mm Allen Keys Torque Wrench Press fit Headset or BB Press Loctite 638 BEARING RETAINER!! (Very Important) 2-Arm Gear Puller Crown race puller SLED

More information

Thor Audi A4/S4 Skid Plate Installation Instructions

Thor Audi A4/S4 Skid Plate Installation Instructions Thor Audi A4/S4 Skid Plate Installation Instructions Parts List: 1 Aluminum Skid Plate 2 Aluminum Side Wings 10 10mm Flat Washers 3 8mm Flat Washers 3 8mm Speed Clips 2 10x40mm Bolts 3 8x35mm Bolts 2 Rivet-nuts

More information

Model 209 Fireback Replacement

Model 209 Fireback Replacement Model 209 Fireback Replacement Please read all the instructions before you begin the procedure. Confirm that you have all the necessary tools and materials. If you have any questions, technical support

More information

Big Block Installation Manual For Systems without A/C

Big Block Installation Manual For Systems without A/C Big Block Installation Manual For Systems without A/C Billet Specialties, Inc. 500 Shawmut Ave. La Grange, IL 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 Hardware List For Chevrolet Big Block Tru

More information

1 of 2 3/3/2017 4:49 PM

1 of 2 3/3/2017 4:49 PM 1 of 2 3/3/2017 4:49 PM Front Door Window, Assembly Overview 1 - Window guide - Inserted on flange 2 - Door 3 - Inner window recess seal - Inserted on flange 4 - Bolt - 20 Nm 5 - Carrier assembly - Window

More information

Tools required for basic assembly/checking

Tools required for basic assembly/checking ... and for choosing RKR BMX, you have chosen wisely! RKR is very different from other mini bike brands on the market; It was designed by riders, for riders and is the product of many years experience

More information

Big Block Chevrolet Installation Manual For Systems with A/C #14220 / #14120

Big Block Chevrolet Installation Manual For Systems with A/C #14220 / #14120 Big Block Chevrolet Installation Manual For Systems with A/C #14220 / #14120 Billet Specialties, Inc. 500 Shawmut Ave. La Grange, IL 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 PLEASE READ ALL INSTRUCTIONS

More information

Medium HoneyBadger Chase Rack Installation Instructions

Medium HoneyBadger Chase Rack Installation Instructions PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading

More information

Introduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions

Introduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop

More information

MAG-CONV Basic, 48, 48R & Midline Front Mount

MAG-CONV Basic, 48, 48R & Midline Front Mount Parts Required: Tools Used: Mag Wheels Brakes Brake Rods Mounting Bracket Anti Tippers 7/16" Wrench Screw Driver Rubber Mallet 5/8 Wrench 5mm Allen Wrench Step Execution Figures 1 Remove front 5" total

More information

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing

More information

00108/00110 INSTRUCTION MANUAL

00108/00110 INSTRUCTION MANUAL 00108/00110 INSTRUCTION MANUAL Removable and Adjustable Mudflap System IMPORTANT! Exhaust Systems Note: Any modifications to the factory installed exhaust system may void your manufacturer s warranty.

More information

Removing Right-Side. Components. Right-Side. Components. Click Here to Go Back AT THIS POINT

Removing Right-Side. Components. Right-Side. Components. Click Here to Go Back AT THIS POINT Click Here to Go Back NOTE: There is an oil passage beneath the driven gear/drive gear assembly. This passage should be plugged prior to removing the driven gear and drive gear. Failure to do so could

More information

RULTRACT RETRACTOR CABLE REPLACEMENT INSTRUCTIONS. Rultract, Inc. is the ONLY authorized service center in the U.S.A.

RULTRACT RETRACTOR CABLE REPLACEMENT INSTRUCTIONS. Rultract, Inc. is the ONLY authorized service center in the U.S.A. RULTRACT RETRACTOR CABLE REPLACEMENT INSTRUCTIONS Rultract, Inc. is the ONLY authorized service center in the U.S.A. When your Rultract instrument needs repair or service, contact Rultract Inc. or Rultract

More information

Chin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets. Contents

Chin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets. Contents Chin Strap Chin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets Contents BTM-1 1.1 Chin Strap BTM-4 1.2.3.1 Preparation BTM-1 1.1.1 Chin Strap Removal BTM-4 1.2.3.2 Disassembly BTM-1 BTM-2

More information

Click Here to Go Back

Click Here to Go Back Click Here to Go Back Fig. -94 Fig. -97 CC42D 10. Remove the cap screw securing the gear shift stopper plate pin retainer; then remove the retainer. Fig. -95 CC45D 12. Remove the link arm and account for

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT

JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll

More information

Service Bulletin RevMaster Pro Bottom Bracket Rework

Service Bulletin RevMaster Pro Bottom Bracket Rework 15540 Woodinville-Redmond Rd NE #A100 Woodinville, WA 98027 Technical Support (425) 482-6773 ext. 107 or 109 Service Bulletin RevMaster Pro Bottom Bracket Rework Reason for service: There has been cases

More information

Midwest RDH Handpiece Repair Procedure

Midwest RDH Handpiece Repair Procedure Midwest RDH Handpiece Repair Procedure The Midwest RDH handpiece is fairly common and is used by hygienists to clean teeth. The most common problems for this handpiece include a bad prophy head or a dirty

More information

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems without A/C #13605 / #13625

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems without A/C #13605 / #13625 Small lock Ford 289 / 302 / 351W / 5.0 Installation Manual For Systems without /C #13605 / #13625 illet Specialties, Inc. 500 Shawmut venue. La Grange, Illinois 60526 Tech Line (708) 588-0505 Fax (708)

More information

AR-15 Armorer s Essentials Kit. Product # Instructions # Revision: B

AR-15 Armorer s Essentials Kit. Product # Instructions # Revision: B AR-15 Armorer s Essentials Kit Product #156111 Instructions #1025769 Revision: B 1 INDEX 3 AR-15 Adjustable Receiver Link 3 Pivot Pin and Roll Pin Installation Tool 4 Mag well Vise Block 7 Upper Vise Block

More information

RBP-1215B-RX DODGE RAM QUAD CAB RX3

RBP-1215B-RX DODGE RAM QUAD CAB RX3 RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side

More information

MSR/MSB Mechanical Setting Tool

MSR/MSB Mechanical Setting Tool Tech Unit No: 0620000004 Revision: C Approved By: Quality Engineer Date: 201-1-9 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical

More information

MODELS 49 RA 49 RAZ 49 RAC

MODELS 49 RA 49 RAZ 49 RAC General Safety and Maintenance Manual MODEL grinder featuring a rear exhaust. Model Number Exhaust Direction REAR Throttle Type (L) Lever or (K) Safety Lever Speed 12000 to 14000 R.P.M (13500rpm is standard)

More information

AUC Cell Assembly Torque Stand. User Manual

AUC Cell Assembly Torque Stand. User Manual AUC Cell Assembly Torque Stand User Manual WARRANTY Spin Analytical Inc., warrants this product to be defect free in both material and workmanship for 90 days from the date of shipment. Labor services

More information

KAWASAKI KLRE PD NERF HTP4-8-5 & HIGHWAY PEGS HTP4-1-4B

KAWASAKI KLRE PD NERF HTP4-8-5 & HIGHWAY PEGS HTP4-1-4B Thank you for purchasing Happy Trails products. Our products are proudly hand made in Boise Idaho, USA. If you have any questions or concerns about the installation of this product, please contact us directly

More information

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems

More information

1 of 12 5/24/2015 9:43 AM

1 of 12 5/24/2015 9:43 AM 1 of 12 5/24/2015 9:43 AM REAR PROPELLER SHAFT ASSEMBLY Components REMOVAL 1. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY 2 of 12 5/24/2015 9:43 AM a. Place match marks on the propeller shaft flange

More information

Metroboard Pulley Replacement Procedure

Metroboard Pulley Replacement Procedure Metroboard Pulley Replacement Procedure 1) Remove the two transmission cover screws (1/8 allen driver). Then remove the transmission cover. Note there is a split lock washer and flat washer as well, so

More information

3 Emergency Breakaway Coupling

3 Emergency Breakaway Coupling SM64227 July 2008 Applicable addition manuals: N/A Aerospace Group Conveyance Systems Division Carter Ground Fueling Maintenance & Repair Manual 3 Emergency Breakaway Coupling Model 64227 Table of Contents

More information

H8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP)

H8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP) SERVICE MANUAL H8508 Impact Wrench Model 48755 (Serial Code FWN) Model 48760 (Serial Code FWP) Read and understand all of the instructions and safety information in this manual before operating or servicing

More information

Snap Tabs, Chin Strap, Swing Catch, Sealed Pull Pins Stainless Steel. Contents

Snap Tabs, Chin Strap, Swing Catch, Sealed Pull Pins Stainless Steel. Contents Snap Tabs, etc. Stainless Steel Helmets Snap Tabs, Chin Strap, and Earphone Retainers Snap Tabs, Chin Strap, Swing Catch, Sealed Pull Pins Stainless Steel Contents SSBTM-1 1.1 Snap Tabs, Chin Strap, and

More information

JK Rear Crusher Flares

JK Rear Crusher Flares INSTALLATION INSTRUCTIONS INST-17-05-010_A JK Rear Crusher Flares IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Fifth Wheel Adapter Titan 999T5 W4198 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Fifth Wheel Adapter

More information

Replacing the Spindle Bearings Detailed Instructions

Replacing the Spindle Bearings Detailed Instructions Replacing the Spindle Bearings Detailed Instructions These are detailed instructions on how to replace the spindle bearings on a 9x20 lathe sold by many suppliers and made in China. The YAHOO 9x20Lathe

More information

WPS crew Doors Installation instructions

WPS crew Doors Installation instructions WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left

More information

General Four-Way Operation, Maintenance & Service Manual

General Four-Way Operation, Maintenance & Service Manual General Four-Way Operation, Maintenance & Service Manual SCOPE Included in the following pages you will find assembly drawings, exploded views, parts lists, assembly tips, operational descriptions and

More information

DRIVE COMPONENTS REMOVAL. 9. FXCW/C: see Figure Remove bolt (9), sprocket retainer (8), and thrust washer (7). NOTE PRIMARY DRIVE LOCKING TOOL

DRIVE COMPONENTS REMOVAL. 9. FXCW/C: see Figure Remove bolt (9), sprocket retainer (8), and thrust washer (7). NOTE PRIMARY DRIVE LOCKING TOOL DRIVE COMPONENTS REMOVAL PART NUMBER HD-7977 TOOL NAME PRIMARY DRIVE LOCKING TOOL S To remove the primary chain, remove compensating sprocket, clutch assembly and primary chain as an assembly:. Remove

More information

High Rise Sit-Stand Desk Converter

High Rise Sit-Stand Desk Converter High Rise Sit-Stand Desk Converter Assembly Instructions for Model DC350 Patent No. 9,332,839 PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the video

More information

CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL

CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL Serial Number Location SERIAL 8 Record your Serial number and purchase date here: S/N PURCH.DATE: DEALER: Scan this QR code with your PortableDevice to link

More information

High Rise Sit-Stand Desk Converter

High Rise Sit-Stand Desk Converter High Rise Sit-Stand Desk Converter Assembly Instructions for Model DC300 Patent Pending PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the video at

More information

HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual)

HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) IMPORTANT NOTE: Read before beginning installation. These instructions replace all of Step 1 of the instructions

More information

Fig Remove chain cover plate bolts. Fig Remove hammer member. Fig Loosen set screws at base of 12-tooth sprocket.

Fig Remove chain cover plate bolts. Fig Remove hammer member. Fig Loosen set screws at base of 12-tooth sprocket. Fig. 17.2. Remove chain cover plate bolts. Fig. 17.1. Remove hammer member. Fig. 17.3. Remove chain cover plate. Fig. 17.4. Loosen set screws at base of 12-tooth sprocket. Page 61 Fig. 17.5. Remove socket

More information

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models -J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com

More information

Hardinge FlexC Dead-Length Collet System Style DL 42mm. Installation Instructions and Parts Lists

Hardinge FlexC Dead-Length Collet System Style DL 42mm. Installation Instructions and Parts Lists Hardinge FlexC Dead-Length Collet System Style DL 42mm Installation Instructions and Parts Lists 1 General Safety Information Before installing the Hardinge FlexC Collet System on your machine tool, thoroughly

More information

Ford FE Installation Manual For Systems with A/C #14700 / #14720

Ford FE Installation Manual For Systems with A/C #14700 / #14720 Ford FE Installation Manual For Systems with A/C #14700 / #14720 Billet Specialties, Inc. 500 Shawmut Avenue. La Grange, Illinois 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 PLEASE READ ALL INSTRUCTIONS

More information

Elimination of Elevator Bounce

Elimination of Elevator Bounce For the Agilent Archon Autosampler Rework Instructions CAUTION This kit is intended for use by Agilent Service personnel only. Elevator Removal 1 Open top cover. 2 Open front lower door. 3 Remove vial

More information

JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT

JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK002 / KRJW014T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll

More information

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT: 1963-1972 C10 Chevy Truck Custom IFS Installation Instructions Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE PARTS LIST BELOW

More information

USSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS

USSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS 1 OF 17 A 1. PURPOSE: Instructions for in field replacement of 9004 mechanical suspension top pan 2. SCOPE: 9004 mechanical suspension with legacy two point LX back frame and current LX back frame 3. PROCEDURE:

More information

INSTALLATION MANUAL CHEVROLET SMALL BLOCK V3120 / V3220

INSTALLATION MANUAL CHEVROLET SMALL BLOCK V3120 / V3220 INSTALLATION MANUAL CHEVROLET SMALL BLOCK V3120 / V3220 Billet Specialties, Inc. 500 Shawmut Avenue La Grange, Illinois 60526 TECH Line 708.588.0505 Fax 708.588.7181 www.billetspecialties.com PLEASE READ

More information

OPERATIONS MANUAL. Port-O-Slitter

OPERATIONS MANUAL. Port-O-Slitter Tapco Products Company The World Leader in Specialty Tools for the Professional Port-O-Slitter OPERATIONS MANUAL General instructions, set up, accessories and guide to using your portable precision slitting,

More information

It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating loose.

It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating loose. Installation instructions for FC12 Forward Controls for Kawasaki Vulcan 750 It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating

More information

MSR/MSB Mechanical Setting Tool

MSR/MSB Mechanical Setting Tool Tech Unit No: 0620000004 Revision: B Approved By: Quality Engineer Date: 2014-12-16 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical

More information

4/29/2016 Big Block Main Bearing Stud Girdle Kit HUG7380K For B & RB Blocks

4/29/2016 Big Block Main Bearing Stud Girdle Kit HUG7380K For B & RB Blocks Big Block Main Bearing Stud Girdle Kit HUG7380K For B & RB Blocks Contents of Kit 2-4.40 Main Studs 8-5.187 Main Studs 1- Girdle Plate 18- ½ ARP black flat washers 8- ½-20 Grade 8 plain hex nuts 8- ½-20

More information

Installation instructions for FC17 Forward Controls for Triumph Rocket III Roadster

Installation instructions for FC17 Forward Controls for Triumph Rocket III Roadster Installation instructions for FC17 Forward Controls for Triumph Rocket III Roadster It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating

More information

Serial Number Location

Serial Number Location GL/GLX STRENGTH TRAINING SYSTEM OWNERS MANUAL Serial Number Location SERIAL 3 4 5 7 8 Record your Serial number and purchase date here: S/N DATE: DEALER: Model No. BCG-GL BODYCRAFT is a division of Recreation

More information

MODEL H " BYRD SHELIX CUTTERHEAD INSTRUCTIONS

MODEL H  BYRD SHELIX CUTTERHEAD INSTRUCTIONS MODEL H9291 12" BYRD SHELIX CUTTERHEAD INSTRUCTIONS The Model H9291 12" Byrd Shelix cutterhead is designed to replace the straight-knife cutterhead on the Grizzly jointer Model G0609. The total procedure

More information

C70 Window Roller Repair Taken from: Heres the problem:

C70 Window Roller Repair Taken from:  Heres the problem: C70 Window Roller Repair Taken from: http://www.volvospeed.com/vs_forum/topic/115086-how-to-c70-window-rollers-permanent-fix/ Heres the problem: This happened to two separate window assemblys on my c70

More information

WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. WARNING. Ranger XP Door Kit

WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury. WARNING. Ranger XP Door Kit REVISION 04 November, 20 2018 Ranger XP Door Kit Prior to installation, please verify if a revised version of this instruction sheet is available on Knowledge Center. The following symbols may be used

More information