STEP BY STEP INSTALLATION INSTRUCTIONS. Honeycomb Shades. Standard Control, Top Down/Bottom Up & Standard 2-on-1

Transcription

1 STEP BY STEP INSTALLATION INSTRUCTIONS Honeycomb Shades Standard Control, Top Down/Bottom Up & Standard 2-on-1

2 Table of Contents Everything You Need Step 1 - Getting Started....3 Overview - Standard Control, Top Down/Bottom Up & 2-on Step 2 - Mounting the Brackets Inside Mount, Outside Mount, Side Mount, Extension Brackets Step 3 - Hanging the Shade...7 A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at or visit for more info on installation. We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be a painless as possible. Breakaway Cord Connector...7 Step 4 - Operating the Shade...8 Step 5 - (Optional) Hold Down Brackets...9 Level the Bottom Rail...9 Care & Cleaning...10 Safety...10 Warranty...Back Cover Customer Service Hours Monday Friday: 6am 7pm PT Saturday Sunday: 7am 4pm PT smithandnoble.com 1 smithandnoble.com

3 Step 1 Parts & Tools Overview Getting Started First, make sure you have all the parts and tools required to install your shades. ALL THE HARDWARE YOU LL NEED: Pencil, screw-driver, ¼ nut driver, level, and a drill with a 1 16 drill bit. HEADRAIL Standard Control, Top Down/Bottom Up & Standard 2-on-1 Locate wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. DRAW CORD SCREWS MOUNTING S LEVEL (NOT INCLUDED) STANDARD EXTENSION (OPTIONAL) TOP DOWN/BOTTOM UP 2-ON-1 SCREW DRIVER & PENCIL (NOT INCLUDED) SIDE MOUNT (OPTIONAL) POWER DRILL (NOT INCLUDED) HOLD DOWN (OPTIONAL) 3 smithandnoble.com

4 Step 2 Mounting Brackets Step 2 Mounting Brackets Inside Mount Hold the shade inside the window frame so that the front edge of the shade and the front edge of the window line up. Don t forget to keep it centered (you ll want the spaces between the ends of the headrail and window edges to be equal). End brackets should be located 2 1 2" in from each end. Attach the two brackets flat against the top window sill frame. Use the top two bracket holes. QTY QTY INSIDE MOUNT OUTSIDE MOUNT SHADE WIDTH 2 2 up to 40" 3 4* " 72" 4 5* " 84" 5 6* " 120" *It is recommended to use a second bracket on shades over 40" wide located next to the end bracket at the cord lock. Rail Keyhole Slot Side Mount (optional) con't Hook one bracket onto the screw in the window frame, using the keyhole slot. Bring the other end bracket over the screw at the other side of the frame. Slide down, flexing bracket inward until the screw engages in the keyhole slot. Make sure both brackets are slipped down all the way in the keyhole slot so that the screw is in the top portion of the keyhole slot. Pull fabric forward. Install a screw in the bottom hole of each bracket. Tighten all screws. Outside Mount Side Mount (optional) Line the bracket top with the desired height of the top of the headrail. Mark holes for screws. Remove brackets and drill holes. Insert screws for keyhole slots only. Approximately 1 8" of the screw should be left protruding. Pull the cord lock assembly partially out of the headrail and slide the bracket on as shown. Push the cord lock assembly and bracket back all the way into the rail. Remove the end cap from the opposite end of the headrail. Slide the remaining side mount bracket onto the headrail. Replace the end cap before sliding the bracket all the way into the headrail. MOUNTING First, hold the shade above the window so that it s perfectly centered. Using a pencil, mark where the ends of the headrail hit the window frame or the wall. Notes on accuracy: brackets should be evenly spaced, level with one another, and not too close to the headrail s edges and operating mechanism. Next, using the screws provided, mount the brackets to the window frame or wall above the window with the screws provided. Use the rear bracket holes. The bracket requires a minimum surface of 3 4" high. Extension Brackets (optional) Optional Extension Brackets are used to project the back of the shade up to 2 3 8" from the mounting surface. Attach the Mounting Bracket to the Extension MOUNTING Bracket with the nut and bolt provided. 5 smithandnoble.com /8 EXTENSION 2 3 8" EXTENSION

5 Step 3 Hanging the Shade Step 4 Operating the Shade Inserting the Headrail HEADRAIL Standard Control Unwind the cord from the shade. Opening and closing your new Smith 1. Hold the shade up near the brackets and insert the front clip of the bracket into the front groove of the rail. 2. Make sure the shade is centered in the window opening at the desired height. 3. Push the rail back and up until the HEADRAIL & Noble shades is entirely hassle-free. To lower it, pull the cord down and toward the center of the shade. To lock it into position, move the cord past the outside edge and then release. To raise it, pull straight down on the cord until it s at your desired height then move cord past edge to lock. And back clips of the bracket are inserted remember to always keep the draw into the back groove of the rail. cord wrapped around the cord cleat To remove the shade, reverse the procedure. when not in use (that s what you attach to the wall next to your shade). Top Down/Bottom Up Control Breakaway Cord Connector Keep cords out of the reach of young children. Move cribs and furniture away from blind cords. This shade was built with a cord BREAKAWAY CORD CONNECTOR First, lower the bottom rail of the shade to the window sill by releasing the cord on the left side of the shade. Then, using the cord on the right side of the shade, lower the center rail to the desired position. connector which was designed to break apart when force is applied. To raise the shade, pull the right cord down until the center rail of If your cord connector should happen to break apart, follow the instructions below to reassemble. the shade meets the headrail. Pull down on the left cord and lift the bottom rail to the desired position. And remember to always keep the draw cords wrapped around the cord When the connector is open, each side has a cord coming in at the top, one side has a cord coming in from the bottom. Fit the bottom edges together. The side with the cord fits into the side without the cord. Swing the top ends together and press in the middle to fully connect. cleat when not in use (that s what you attach to the wall next to your shade). 7 smithandnoble.com

6 Step 5 Optional Care & Cleaning and Safety Hold Down Bracket Optional Hold Down Brackets are mounted with the supplied screws. With the shade at its proper drop, place the pin of each Hold Down into the hole in each End Cap and make sure the pins are level and aligned. Mark the screw holes with a pencil. Raise the shade, then screw the Hold Down Brackets into the mounting surface. Care & Cleaning Minimal care and cleaning is needed to maintain the beauty of your shades. To Vacuum: Use brush or dust head attachment. To Dust: Use soft, clean cloth. Level the Bottom Rail Honeycomb Shades use a system that allows easy leveling of the bottom rail. It is designed to make slight adjustments (Less than 1") to level the moving rails of your shade. It is not designed to make length adjustments. Use a flat head screwdriver or a coin (a quarter works the best) to turn the adjustment screw to raise or lower that side of the bottom rail. The adjustment screw is on the underside of the bottom rail. One quarter turn of the screw will move the bottom rail up or down approximately 1 4". Over-turning the adjustment screw (more than 1" of adjustment) can cause the cord to tangle or wedge inside the rail. The screw should turn easily - Do Not Force. ADJUSTMENT SCREWS Safety is Everything We believe that great style should never come at the cost of safety. We strongly recommend using cord cleats on all standard shades to keep draw cords out of reach. Mount the cord cleat at a safe height, taking into account furniture or other objects upon which a child may climb. Then, after each use of the shade, simply wrap the excess cord around the cleat. It's fast, easy and safe. To obtain a free cord cleat call us at or visit smithandnoble.com/childsafety. 9 smithandnoble.com

7 Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at and we ll arrange for a repair or replacement ASAP Smith & Noble Home, Inc. All Rights Reserved SN2018

8 STEP BY STEP INSTALLATION INSTRUCTIONS Honeycomb Shades Loop Control, Top Down/Bottom Up with Loop Control & 2-on-1 with Loop Control

9 Table of Contents Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at or visit for more info on installation. We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be a painless as possible. Step 1 - Getting Started...3 Overview - Loop Control, Top Down/Bottom Up with Loop Control & 2-on-1 with Loop Control...4 Step 2 - Mounting the Brackets Inside Mount, Outside Mount, Side Mount, Extension Brackets, Spacer Block Step 3 - Hanging the Shade...7 Removing the Shade...7 Step 4 - Installing Cord Tensioner...8 Operating the Shade...8 Step 5 - (Optional) Hold Down Brackets...9 Leveling the Bottom Rail...9 Care & Cleaning...10 Safety...10 Warranty...Back Cover Customer Service Hours Monday Friday: 6am 7pm PT Saturday Sunday: 7am 4pm PT smithandnoble.com 1 smithandnoble.com

10 Step 1 Parts & Tools Overview Getting Started First, make sure you have all the parts and tools required to install your shades. ALL THE HARDWARE YOU LL NEED: Pencil, screw-driver, ¼ nut driver, level, and a drill with a 1 16 drill bit. HEADRAIL Loop Control, Top Down/Bottom Up with Loop Control & 2-on-1 with Loop Control Locate wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. LOOP CORD CORD TENSIONER SCREWS MOUNTING S LEVEL (NOT INCLUDED) EXTENSION (OPTIONAL) TOP DOWN/BOTTOM UP 2-ON-1 SCREW DRIVER & PENCIL (NOT INCLUDED) HOLD DOWN (OPTIONAL) POWER DRILL (NOT INCLUDED) SPACER BLOCK (OPTIONAL) 3 smithandnoble.com

11 Step 2 Mounting Brackets Step 2 Mounting Brackets Inside Mount Outside Mount Hold the shade inside the window frame so that the front edge of the shade and the front edge of the window line up. Don t forget to keep it centered (you ll want the spaces between the ends of the headrail and window edges to be equal). End brackets should be located 2 1 2" in from each end. Attach the two brackets flat against the top window sill frame. Use the top bracket holes. QTY SHADE WIDTH 2 up to 40" 3 401/8 72" 4 721/8 84" 5 841/8 and up First, hold the shade above the window so that it s perfectly centered. Using a pencil, mark where the ends of the headrail hit the window frame or wall. (NOTES on accuracy: Brackets should be evenly spaced, level with one another, and not too close to the headrail s edges and operating mechanism.) Next, using the screws provided, mount the brackets to the window frame or wall above the window using the provided screws. Use the rear bracket holes. The bracket requires a minimum surface of 7/8" high. NUT Side Mount with Extension Brackets (optional) Measure from window sill up to desired mounting position on each side of the window frame. Mark position. Mount Extension Brackets on each side of window frame, as shown. Make sure to confirm that the headrail will sit NUT EXTENSION BOLT 2" 2 3 8" EXTENSION Extension Bracket requires 2" flat surface for mounting Extension Brackets (optional) Optional Extension Brackets are used to project the back of the shade up to 2 3 8" from the mounting surface. Attach the Installation Bracket to the Extension Bracket with the nut and bolt provided. perfectly level. Once the Extension Brackets are installed and properly positioned, attach the mounting brackets using the nuts and bolts provided. BOLT MOUNTING Outside Mount with Spacer Block (optional) Optional Spacer block will project bracket 3 8" from the mounting surface. 5 smithandnoble.com

12 Step 3 Hanging & Removing the Shade Step 4 Operating the Shade Inserting the Headrail Cord Tensioner Installation First, lower the middle and bottom rails about an inch. This will help keep the fabric from getting caught between the brackets and the headrail. Position the headrail with the front lip (A) resting on the top hooks of all the brackets. Make sure that no fabric is pinched between the brackets and the headrail. Push the bottom of the headrail firmly upwards and toward the window until the groove at the bottom of the headrail snaps into place, (B) as shown. (A) Push up and toward the window (B) Your window shade has arrived with the cord tensioner positioned near the head rail to comply with current child safety standards. The cord tensioner must be mounted and secured before the window shade will operate correctly. The tension device reduces the hazards of strangulation and entanglement of young children by limiting access to the control cord. The cord tensioner must be installed to make the shade fully operational. Please read the instructions included in the cord tensioner mounting hardware packet prior to installation. Removing the Shade Figure (B) - To remove a shade, insert a screwdriver between the headrail and the bottom back of the bracket (tab which extends out slightly from each bracket). Gently pry the screwdriver to release the bracket from the headrail. Take care not to damage the headrail. As you release the brackets, support the headrail to keep it from falling. (B) Insert screwdriver here and gently pry Operating the Shade Opening and closing your new Smith & Noble shades is entirely hassle-free. Pulling down on the back cord will lower the shade. Pulling down on the front cord will raise the shade. Do not lift the bottom rail with your hands. Also, be careful not to place objects on the window sill that will interfere with operating the shade or cause it to hang unevenly. The cord tensioner must be installed to make the shade fully operable. 7 smithandnoble.com

13 Step 5 Optional Care & Cleaning and Safety Hold Down Bracket (optional) Optional Hold Down Brackets are mounted with the supplied screws. With the shade at its proper drop, place the pin of each Hold Down into the hole in each End Cap and make sure the pins are level and aligned. Mark the screw holes with a pencil. Raise the shade, then screw the Hold Down Bracket into the mounting surface. Care & Cleaning Minimal care and cleaning is needed to maintain the beauty of your shades. To Vacuum: Use brush or dust head attachment. To Dust: Use soft, clean cloth. Level the Bottom Rail Honeycomb Shades use a system that allows easy leveling of the bottom rail. It is designed to make slight adjustments (Less than 1") to level the moving rails of your shade. It is not designed to make length adjustments. Use a flat head screwdriver or a coin (a quarter works the best) to turn the adjustment screw to raise or lower that side of the bottom rail. The adjustment screw is on the underside of the bottom rail. One quarter turn of the screw will move the bottom rail up or down approximately 1 4". Over-turning the adjustment screw (more than 1" of adjustment) can cause the cord to tangle or wedge inside the rail. The screw should turn easily - Do Not Force. ADJUSTMENT SCREWS Safety is Everything We believe that great style should never come at the cost of safety. To protect young children and pets in your home, we ve included a cord tensioner to secure all loop control cords and prevent possible entanglement. Please see the enclosed pamphlet for details. We strongly recommend using cord cleats on all standard shades to keep draw cords out of reach. To obtain a free cord cleat call us at or visit smithandnoble.com/childsafety. 9 smithandnoble.com

14 Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at and we ll arrange for a repair or replacement ASAP Smith & Noble Home, Inc. All Rights Reserved SN2018

15 STEP BY STEP INSTALLATION INSTRUCTIONS Honeycomb Shades Cordless, Cordless Top Down/Bottom Up & 2 on 1 with Cordless

16 Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at or visit for more info on installation. We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be a painless as possible. Table of Contents Step 1 - Getting Started...3 Overview - Cordless Control, Top Down/Bottom Up, 2-on Step 2 - Mounting the Brackets Step 2 - Extension Brackets...6 Step 2 - Spacer Block...6 Step 3 - Installing the Headrail...7 Step 4 - Operating the Shade...8 Step 4 - Expandable Pole Operation...8 Step 5 - Removing the Shade...9 Step 5 - Level the Bottom Rail...9 Troubleshooting...10 Hold Down Brackets (optional)...10 Safety...Back Cover Care & Cleaning...Back Cover Warranty...Back Cover Customer Service Hours Monday Friday: 6am 7pm PT Saturday Sunday: 7am 4pm PT smithandnoble.com 1 smithandnoble.com

17 Step 1 Getting Started Overview Getting Started First, make sure you have all the parts and tools required to install your shades. ALL THE HARDWARE YOU LL NEED: Pencil, screwdriver, ¼ nut driver, level, and a drill with a 1 16 drill bit. HEADRAIL Cordless Control, Top Down/Bottom Up, 2-on-1 Headrail Then find wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. SCREWS MOUNTING S HANDLE TOP DOWN/BOTTOM UP 2-ON-1 POWER DRILL (NOT INCLUDED) EXTENSION (OPTIONAL) SCREW DRIVER & PENCIL (NOT INCLUDED) HOLD DOWN (OPTIONAL) LEVEL (NOT INCLUDED) SPACER BLOCK (OPTIONAL) 3 smithandnoble.com

18 Step 2 Mounting the Brackets Step 2 Mounting the Brackets Inside Mount Outside Mount Hold the shade inside the window frame so that the front edge of the shade and the front edge of the window line up. Don t forget to keep it centered (you ll want the spaces between the ends of the headrail and window edges to be equal). End brackets should be located 2 1 2" in from each end. Attach the two brackets flat against the top window sill frame. Use the top two bracket holes. QTY SHADE WIDTH 2 up to 40" 3 401/8 72" 4 721/8 84" 5 841/8 120" First, hold the shade above the window so that it s perfectly centered. Using a pencil, mark where the ends of the headrail hit the window frame or wall. Notes on accuracy: brackets should be evenly spaced, level with one another, and not too close to the headrail s edges and operating mechanism. Next, mount the brackets to the window frame or wall above the window using the provided screws. Use the rear bracket holes. The bracket requires a minimum surface of 7 8" high. (continue on to STEP 3 - Hanging the Shade p7) Side Mount with Extension Brackets (optional) Measure from window sill up to desired mounting position on each side of the window frame. 2" Extension Bracket requires 2" flat surface for mounting EXTENSION NUT Extension Brackets (optional) Optional Extension Brackets are used to project the back of the shade up to 2 3 8" from the mounting surface. Attach Mark position. Mount Extension Brackets the mounting bracket to the Extension on each side of window frame as shown. Make sure to confirm that headrail will sit perfectly level. Once Extension Brackets EXTENSION NUT MOUNTING 2 3 8" BOLT Bracket with the nut and bolt provided. are installed and properly positioned, attach the mounting brackets using the nuts and bolts provided. BOLT SPACER BLOCK Outside Mount with Spacer Block (optional) Optional Spacer block will project bracket 3 8" from the mounting surface. 5 smithandnoble.com

19 Step 3 Installing the Headrail Step 4 Operating the Shade Installing the Headrail Hard to Reach Operation First, lower the middle and bottom rails about an inch. This will help keep the fabric from getting caught between the brackets and the headrail. (A) Expandable Pole For hard to reach Cordless shades use expandable pole to raise and lower shades. Position the headrail with the front lip (A) resting on the top hooks of all the brackets. Make sure that no fabric is pinched between the brackets and the headrail. Push the bottom of the headrail firmly upwards and toward the window until the groove at the bottom of the headrail snaps into place, (B) as shown. Push up and toward the window (B) Lower the shade Raise the shade To Lower the shade, Insert the hook into the slot on the handle and pull gently. To Raise the shade simply center the poles end under the bottom rail. Cordless Control Opening and closing your new Smith & Noble shades is entirely hassle-free. To lower it, pull the handle down, to raise it, push the handle up until it s at your desired height then release. CORDLESS HANDLE Cordless, Cordless with Top Down/Bottom Up and Cordless 2-on-1 Top Down/Bottom Up Cordless Top Down/Bottom Up Control HEADRAIL MIDDLE RAIL To lower the bottom rail pull down the handle of the shade. Then, using the handle at the top of shade, pull down the middle rail to the desired position. To raise the shade, pull the handle up until the middle rail of the shade meets the headrail. Pull bottom handle to the desired position. BOTTOM RAIL 7 smithandnoble.com

20 Step 5 Removing the Shade & Leveling Troubleshooting & Hold Down Bracket Removing the Shade To remove a shade, insert a screw-driver between the headrail and the bottom back of the bracket (tab which extends out slightly from each bracket). Gently pry the screwdriver to release the bracket from the headrail. Take care not to damage the painted finish of the headrail. As you release the brackets, support the headrail to keep it from falling. Insert screwdriver here and gently pry Hold Down Bracket (optional) Optional Hold Down Brackets are mounted with the supplied screws. With the shade at its proper drop, place the pin of each Hold Down into the hole in each End Cap and make sure the pins are level and aligned. Mark the screw holes with a pencil. Raise the shade, then screw the Hold Down Bracket into the mounting surface. Troubleshooting Problem Solution Level the Bottom Rail Honeycomb Shades use a system that allows easy leveling of the bottom rail. It is designed to make slight adjustments (Less than 1") to level the moving rails of your shade. It is not designed to make length adjustments. ADJUSTMENT SCREWS 1. The shade will not stay down The fabric may want to spring up because it was fabricated primarily in the closed position. With clean hands, gently pull down on a section of cells to relax the pleats. Repeat with another section of cells until the fabric is relaxed. Do not tightly stack the shade for 24 hours. Gently stretch the fabric. Pull evenly on each side. Use a flat head screwdriver or a coin (a quarter works the best) to turn the adjustment screw to raise or lower that side of the bottom rail. The adjustment screw is on the underside of the bottom rail. One quarter turn of the screw will move the bottom rail up or down approximately 1 4". Over-turning the adjustment screw (more than 1" of adjustment) can cause the cord to tangle or wedge inside the rail. The screw should turn easily - Do Not Force. 2. The pleats billow out when the shade is raised. Pleats may settle and stretch out when left in one position for extended periods of time. Raise the shade very slowly to allow the retraction mechanism to pull up the stretched fabric. Helpful Tip: Shades that are raised regularly will be less subject to pleat settling and will remain looking fresh and new. 9 smithandnoble.com

21 Care & Cleaning /Safety Care & Cleaning Occasional light vacuuming with a soft bristle attachment or gentle feather dusting is all that is required to keep your shades looking fresh and neat. Safety First. Style Second To None. Great style should never come at the cost of safety. Every Smith & Noble window treatment conforms strictly to today s safety standards, including permanent tie-down devices and built-in cord stops. To protect young children and pets, there s no better way to eliminate risk than to use one of our cordless products. Child Safety Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase (hang on to your receipt!) and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. Visit smithandnoble.com/guarantee to see full details. In need of warranty service? Call us at and we ll arrange for a repair or replacement ASAP Smith & Noble Home, Inc. All Rights Reserved SN2018

22 STEP BY STEP INSTALLATION INSTRUCTIONS Honeycomb Shades Motivia Motorization

23 Everything You Need A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience. We recommend saving this guide. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at for more info on installation. Table of Contents Step 1 - Getting Started....3 Overview - Honeycomb Motorization...4 Bracket Quantity & Positioning...4 Step 2 - Mounting the Brackets Inside Mount, Side Mount, Outside Mount, Outside Mount w/spacer Block, Spacer Blocks (Optional) Step 3 - Hanging & Removing the Shade....8 Step 4 - Link the Remote....9 Step 5 - Operating the Shade Step 6 - Adjusting the Motor Limits (if desired) Setting & Using a Favorite Position We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be as painless as possible. Advanced Programing Replacing the Battery & Charging the Motor Level the Bottom Rail & Hold Down Brackets (opt.) Care & Cleaning Instructions Safety Troubleshooting Customer Service Hours Monday Friday: 6am 6pm PT Saturday Sunday: 7am 4pm PT Warranty....Back Cover smithandnoble.com 1 smithandnoble.com

24 Step 1 Parts & Tools Overview Getting Started First, make sure you have all the parts and tools required to install your shades. Motorization HEADRAIL ALL THE HARDWARE YOU LL NEED: Pencil, screw-driver, ¼ nut driver, level, and a drill with a 1 16 drill bit. Then find wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. POWER DRILL (NOT INCLUDED) SCREW DRIVER (NOT INCLUDED) PENCIL (NOT INCLUDED) LEVEL (NOT INCLUDED) REMOTE CONTROL BOTTOM RAIL Bracket Quantity & Positioning SCREWS MOUNTING S CHARGER EXTENSION (OPTIONAL) Shades are shipped with the required number of brackets for proper installation. End brackets should be located approx. 3" from either end. Depending on the width of the shade, additional brackets may be necessary, evenly spaced between the two end brackets. Brackets must be in line and level. Shim brackets on inside mounts if necessary. The head rail must be level for the shade to operate properly. HOLD DOWN (OPTIONAL) SPACER BLOCKS (OPTIONAL) QTY SHADE WIDTH 2 up to 40" 3 >40 1 8" 72" 4 >72 1 8" 84" 5 >84 1 8" and up 3 smithandnoble.com

25 Step 2 Mounting Brackets Step 2 Mounting Brackets Inside Mount Hold the shade inside the window frame so that the front edge of the shade and the front edge of the window line up. Don t forget to keep it centered (you ll want the spaces between the ends of the headrail and window edges to be equal). End brackets should be located 3" in from 3" 2¼" 2 ¼" MINIMUM DEPTH NEEDED TO FULLY RECESS SHADE TO WALL. Outside Mount The minimum mounting height for outside mounted shades is 7 8". The brackets are mounted with two screws through the back end of the bracket flat against the window molding or the wall above the window. each end. Use the top bracket holes. Attach the two brackets flat against the top window sill frame. Side Mount (Optional) Line the side mount bracket up with the desired height of the top of the headrail. Measure from the window sill up to SIDE MOUNT 2" NUT MOUNTING the desired mounting position on each side of the window frame. BOLT Mark holes for screws. Remove brackets and drill holes. Mount the side mount brackets on each side of window frame as shown. Make sure to confirm that the headrail will sit perfectly level. Attach the brackets together, using the nuts and bolts provided. 5 smithandnoble.com

26 Step 2 Mounting Brackets Step 3 Hanging & Removing the Shade Spacer Blocks - Outside Mount (Optional) Each spacer blocks projects brackets 1 2" away from the mounting surface. Make sure that the brackets are level and aligned. Attach using the 2 screws that were provided in the package with the spacers. Screws should be long enough to secure the bracket to the mounting surface. (A) Push up and toward the window Hanging the Shade Before mounting the headrail make sure that the receiver wire is out of the headrail. For optimal performance position the receiver wire so that it is facing into the room. Position the motor wire so that it comes out the back side of the shade. Position the headrail with the front lip (A) resting on the top hooks of all the brackets. Make sure that no fabric is pinched between the brackets and the headrail. (B) Push the bottom of the headrail firmly upwards and toward the window until the groove at the bottom of the headrail snaps into place, (B) as shown. Make sure that no fabric is pinched between the brackets and the headrail. Be sure the motor wire is not pinched by Extension Brackets - Outside Mount (optional) EXTENSION NUT the bracket. Optional Extension Brackets are used to project the back of the shade up to 2 3 8" from the mounting surface. Attach 2 3 8" BOLT Removing the Shade the Mounting Bracket to the Extension Insert a screwdriver between the headrail Bracket with the nut and bolt provided. and the bottom back of the bracket (tab 2" which extends out slightly from each bracket). (dia. C) Extension Bracket requires 2" flat surface for mounting (C) Gently pry the screwdriver to release the bracket from the headrail. Insert screwdriver here and gently pry 7 smithandnoble.com

27 Step 4 Link the Remote Control Step 5 Operating the Shade Link the Remote Control Remote Control The remote control has multiple For added protection, your remote control channels. Before linking the remote, arrived with a protective film on the top. determine which shade(s) you want Please remove this film prior to use. on which channel. The remote has 5 channels. All shades linked to the remote will also automatically be programmed to the "ALL" channel. 1. Press the SETTING button on the motor until the shade jogs twice. Settings (black button) located inside the honeycomb headrail Protective Film Select the desired channel with the CHANNEL key. The channel indicator light will illuminate the channel that is on. If all 5 lights are lit, the remote will control all 5 channels at once. Release the button immediately after the first jog this should not be more than 3 seconds. Tapping the UP or DOWN keys for less than 2 seconds will move the shade in short steps. Holding the UP or DOWN 2. Repeat this step for all shades that will be controlled by the same channel. 3. Repeat step 2. Select the channel keys down for more than 2 seconds before releasing, will operate the shade in the faster standard speed. that you want to program using the CHANNEL selector button. Channel Display Press the UP or DOWN keys to raise or lower the shade. Vanes will open when 4. Press and hold the CONFIRM button until the shade(s) jogs once. The shade is now linked to the remote. 5. Repeat steps 1-3 to program the rest of the shades. Limit Button Confirm Button Up Stop Down Channel + Channel shade is completely lowered. Press the STOP key to stop the shade anywhere along the window. BACK OF REMOTE FRONT OF REMOTE 9 smithandnoble.com

28 Step 6 Adjust Motor Limits (if desired) Step 6 Adjust Motor Limits (if desired) Remote Control Lower Limit For The lower and upper limits have Hold the LIMIT button until the shade been set at the factory. If you need to stops jogging. make adjustments to the limits, follow the instructions below. Please Note: When clearing the factory set limits, both the upper and lower limits will need to be reset. Channel Display Up Use the DOWN button to lower the shade. Press STOP when the shade is near the desired lower limit. Use the UP and DOWN buttons to adjust the length more accurately. Use the CHANNEL buttons to select the channel for the shade that needs to be adjusted. Then follow the directions below. When adjusting one shade, the other shades on that channel need to be temporarily unlinked from the remote. To unlink a shade, remove the shade from the window, press and hold the black SETTING button on motor until it completes one jog - jog/jog cycle and then release the SETTINGS button. Repeat for all other shades on that channel. FRONT OF REMOTE Stop Down Channel + Channel BACK OF REMOTE Limit Button Confirm Button Hold the CONFIRM button until the shade jogs. This locks in the lower limit. Upper Limit Use the UP button to raise the shade. Press stop when the shade is near the desired upper limit. Use the UP and DOWN buttons to adjust the upper limit more accurately. Hold the CONFIRM button until the shade jogs. This locks in the upper limit. Follow the limit settings instructions below and then relink "turned off" shades by following the steps under LINK REMOTE section on pg 8. Note: If you also desire to set a favorite position, you should do so prior to relinking other shades on that channel. See the next page for setting FAVORITES. 11 smithandnoble.com

29 Setting & Using a Favorite Position Advanced Programming Remote Control When adding a favorite position to one shade, the other shades on that channel need to be temporarily unlinked from the remote. To unlink a shade, press and hold the SETTING button until it completes one jog-jog/jog cycle and then release the SETTING button. Repeat for all other shades on that channel. Motor Motor Replacing Original Remote, Adding Additional Remote or Adding Shade(s) to an Additional Channel Press the SETTINGS button on the motor until the shade jogs once. Release the button immediately after the first jog - this should not be more than 3 seconds. Setting and Using the Favorite Position Use the UP or DOWN buttons to position the shade at the desired favorite position. First press and hold the LIMIT button on the back of the remote with a small screwdriver or tip of a pen. While holding the LIMIT button press and hold the UP button. Release both buttons when the shade jogs. With the shade at either the upper or lower limit, simply press the STOP button to bring the shade to the favorite position. To go to the favorite position from any other location, make sure the shade has been stopped for at least three seconds before pressing the STOP button. Settings (black button) located inside the honeycomb headrail Channel Display Up Stop Down Channel + Channel Settings (black button) located inside the honeycomb headrail Limit Button Confirm Button Repeat this step for all shades that will be controlled by a single channel. Select the channel that you want to program using the CHANNEL selector button. Press and hold the CONFIRM buttonuntil the shade(s) jogs once. Repeat steps 1-4 to program the rest of the channels on a multi-channel remote. Removing a Shade from a Remote or Channel and Link it to a Different Remote or Channel Press and hold the SETTING button until it completes one jog - jog/jog cycle. Changing a Favorite Position Unlink all other shades on the same channel before changing/erasing the favorite positions. FRONT OF REMOTE BACK OF REMOTE Release the SETTINGS button. The original remore or channels have been unlinked. Use the UP or DOWN buttons to position the shade at the desired FAVORITE position. While holding the LIMIT button, quickly press and hold Linking the motor to the new Motor or Channel the UP button. Release both buttons when the shade jogs. To erasea a FAVORITE position, bring the Follow the steps for replacing the remote above. shade to the UPPER limit. Press and hold the LIMIT button on the back of the remote, then press and hold the UP button. Release both buttons when the shade jogs. 13 smithandnoble.com

30 Replacing the Battery, Charging the Motor Level the Bottom Rail, Hold Down Brackets Remote Remove the battery tray from the remote by inserting a fingernail into the indentation on the back of the remote. To avoid the battery falling out of the remote, remove the ray while the remote is face up. ADJUSTMENT SCREW ADJUSTMENT SCREW Level the Bottom Rail Honeycomb Shades use a system that allows easy leveling of the bottom rail. It is designed to make slight adjustments (less than 1") to level the bottom rails of Insert the new battery (CR2430 lithium) into the battery tray so that the writing is facing up (positive up) when the remote is face up. ACCESS DOOR your shade. It is not designed to make length adjustments. Use a flat head screwdriver or a coin Slide the tray back into the remote. (a quarter works the best) to turn the adjustment screw to raise or lower that side of the bottom rail. The adjustment screw is on the underside of the bottom rail. One quarter turn of the screw will move the bottom rail up or down approximately 1 4". Over-turning the adjustment screw (more than 1" of adjustment) can cause the cord to tangle or wedge inside the rail. The Charging the Motor screw should turn easily - Do Not Force. When the shade begins to operate slower than normal it is time to charge the motor. Plug the 8.4v charger into the charging Hold Down Brackets (optional) wire. The charging wire is attached to the back of the head rail at the left end. Plug the charger into an electrical outlet. Optional Hold Down Brackets are mounted with the supplied screws. With the shade at its proper drop, place A red light on the charger indicates that the motor is charging. To fully charge the batteries, allow the batteries to charge for 1 hour after the light on the charger turns green. A typical charge cycle can take between 4-6 hours. CHARGING WIRE HOLD DOWN the pin of each Hold Down into the hole in each End Cap and make sure the pins are level and aligned. Mark the Hold Down screw hole with a pencil. Raise the shade, then screw the Hold Down Bracket into the mounting surface. Slightly flex the hold down brackets to insert the pins into the end caps. 15 smithandnoble.com

31 Care & Cleaning and Safety Troubleshooting Care & Cleaning Minimal care and cleaning is needed to maintain the beauty of your shades. To Vacuum: Use a hand-held vacuum with low suction for a more thorough cleaning to keep your shades looking fresh and neat. To Dust: Use feather duster. Problem The motor does not work The motor continues to run in one direction The indicator light on the remote does not shine or the remotecontrolling range becomes shorter. Solution Recharge motor. The limit setting was unsuccessful and needs to be reset. Replace the battery in the remote (CR2430 Lithium) If these suggestions don t work, then please give us a call or visit our website. Safety First. Style Second To None Great style should never come at the cost of safety. Every Smith & Noble window treatment conforms strictly to today s safety standards, including permanent tie-down devices and built-in cord stops. To protect young children and pets, there s no better way to eliminate risk than to use one of our Motivia motorized products. Child Safety 17 smithandnoble.com

32 Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at and we ll arrange for a repair or replacement ASAP Smith & Noble Home, Inc. All Rights Reserved SN2021 SN_HC_M_2017_8