Osaka 3 Door 4 Drawer Wardrobe

Transcription

1 Osaka Door Drawer Wardrobe Assembly Instructions - Please keep for future reference White Black mensions Width : 100. cm Depth : 5.0 cm Height: 181. cm Assembly Instructions - Please keep for future reference If you need help or have damaged or missing parts, call the Argos Customer Helpline: Issue

2 ! fety and re Advice Important - Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages and. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand or put weight on the product, this could cause damage. Assemble the item as close to its final position (in the same room) as possible. Assemble on a soft level surface to avoid damaging the unit or your floor. Parts of the assembly will be easier with people. We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers. spose of all packaging carefully and responsibly. re and maintenance Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners. From time to time check that there are no loose screws on this unit. This product should not be discarded with household waste. Take to your local authority waste disposal centre. Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference. 1

3 Components - Panels If you have damaged or missing components, call the Argos Customer Helpline: Please check you have all the panels listed below 1 Top (100, cm x 5 cm) 5 vider, large (1,5 cm x 8, cm) 8 H-profile (1,0 cm x 1,7 cm) 7 Back x (17,9 cm x 0,5 cm) Side, left (17,7 cm x 7 cm) Side, right (17,7 cm x 7 cm) 6 vider, small (,7 cm x 8, cm) Post x (179,7 cm x, cm) 9 ttom (88,5 cm x 8, cm) 1 Shelf x (8,8 cm x 7 cm) 15 Drawer back x (9, cm x 9,8 cm) 1 Drawer front x (,8 cm x 15,7 cm) 10 Front rail (88,5 cm x 6 cm) 16 Drawer bottom x (0, cm x,7 cm) 17 Door x (1,1 cm x 9,1 cm) Back rail (88,5 cm x 7 cm) 1 Drawer side, right/left (5 cm x 9,8 cm) x 8 18 Hanging rail (57, cm x, cm)

4 Components - Fittings Please check you have all the panels listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. Ab ø7.8 x 0mm Wooden dowel x Bp ø6 x 0mm Wooden dowel x 16 ø x 1mm Screw x 6 ø x 5mm Screw x 16 ø15 x 10.5mm m x Fc ø5 x 8, ccmm lt x Fh 1. x 15mm Nail x 50 Fi Back fitting - 1 x 19mm x 6 Fl Back fitting w. ø.5 x 15mm Screw x 8 Fr Support for hanger rail - 15mm x Ge Wall strap and instruction x 1 Hd Shelf support x Hk 8 ø7 x mm Metal Knob x 7 M x 0mm Screw x 7 M x 9mm Screw x 8 ø x 5mm Screw x 0 ø5.8 x 8mm Screw x 0 Ko Me ø5.8 x 19mm Screw x 1 ø, x 9,5mm Screw x 8 ø6mm Cup hinge x Mc Nu ø6mm Cup hinge x 0mm Crossplate x 6 ø18 x 9mm Spacer x 1 Pc Pd Magnet, adjustable x 6 5 x 1 x 1mm Magnet catch x 6 Vl 10 x 17 x 10mm Drawer runner x 8 x x mm Angle x Tools required Flatblade screwdriver (Medium) Phillips screwdriver (Medium & large) Hammer Ruler - Use this ruler to help correctly identify the screws

5 Step 1 Assembly of the wardrobe Step 1.1 Fix the posts onto the sides and using screws into the holes indicated. ø x 5mm Screw x 0 The top of the posts and the sides and must be flush

6 Step 1. Knock the dowels into the holes indicated on the sides and using a small hammer. ø7.8 x 0mm Wooden dowel x 6 ø5 x 8, ccmm lt x 8 Screw the bolts into the holes indicated on the sides and. Step 1. Fl Fix the Crossplates Mc to the sides and using the pre-mounted screws. Note the details. Position the Crossplates Mc exactly as shown. Fix the support for hangerrail Fl onto the left hand side using screw. ø x 1mm Screw x 1 Mc 0mm Crossplate x Mc Support for hanger rail - 15mm x 1 Fl Mc Mc Mc

7 Step 1. Slide the top of the drawer runners backwards. You can identify the front end of the drawer runner by the two M holes. See details. Place the spacers Nu as shown, and fix the front end of the drawer runners to the sides and using screws through the holes number 1 and 7. See details. ø5.8 x 19mm Screw x 8 Nu ø18 x 9mm Spacer x Front end Front end Nu 8 10 x 17 x 10mm Drawer runner x Nu Hole no. 1 Nu Front end Hole no. 7 Hole no. 7 Nu Hole no. 1 Nu Nu Note the hole! ttom end of right hand side Step 1.5 Nu Slide the top of the drawer runners forwards. ø5.8 x 19mm Screw x ø18 x 9mm Spacer x Place the spacers Nu as shown, and fix the back end of the drawer runners to the sides and using screws through the holes indicated. See details. Nu Nu

8 Step 1.6 Knock the dowels into the holes indicated on the large divider 5 and the small divider 6 using a small hammer. ø7.8 x 0mm Wooden dowel x Step 1.7 Fix the Crossplates Mc to the large divider 5 using the pre-mounted screws. Note the details. Position the Crossplates Mc exactly as shown. ø x 1mm Screw x 1 Mc 0mm Crossplate x Fl Support for hanger rail - 15mm x 1 Fl Fix the support for hangerrail Fl onto the large divider 5 using screw. 5 Mc Mc

9 Step 1.8 Slide the top of the drawer runners backwards. You can identify the front end of the drawer runner by the two M holes. Fix the front end of the drawer runners to the divider 6 using screws through the holes number 1 and 7. ø5.8 x 8mm Screw x Front end 6 10 x 17 x 10mm Drawer runner x Hole no. 7 Hole no. 1 Step 1.9 Slide the top of the drawer runners forwards. Fix the back end of the drawer runners to the divider 6 using screws through the holes indicated. 6 ø5.8 x 8mm Screw x Step 1.10 Turn around the small divider 6. ø5.8 x 8mm Screw x 10 x 17 x 10mm Drawer runner x Fix the front end of the drawer runners to the divider 6 using screws through the holes number 1 and 7. 6 Hole no. 7 Hole no. 1 Step 1.11 Fix the back end of the drawer runners to the divider 6 using screws through the holes indicated. ø5.8 x 8mm Screw x

10 Step 1.1 Ko Fix the angles Vl using screws Ko into the holes indicated on the front rail 10. ø5 x 8, ccmm lt x 1 Vl x x mm Angle x ø, x 9,5mm Screw x Ko Ko Vl Vl Ko Step 1.1 Knock the dowels into the holes indicated on the bottom 9 and the back rail 11 using a small hammer. Press the magnets Pc into the holes indicated on the bottom 9. ø7.8 x 0mm Wooden dowel x 8 Pc Magnet, adjustable x 11 9 Pc Pc ø5 x 8, ccmm lt x Pc Step 1.1 Pc Screw the bolts into the holes indicated on the top 1. ø5 x 8, ccmm lt x 9 Magnet, adjustable x Press the magnets Pc into the holes indicated on the top 1. Pc 1 Pc Pc

11 Step 1.15 Place the large divider 5 onto the bottom 9. ø15 x 10.5mm m x Push cams into the holes indicated on the large divider 5. Arrows pointing towards the bottom 9. Turn the cams to the right to fix the large divider Step 1.16 Screw the bolts into the holes indicated on the bottom 9. ø5 x 8, ccmm lt x 9 Step 1.17 Place the bottom 9 and the back rail 11 onto the small divider 6. ø15 x 10.5mm m x Push cams into the holes indicated on the small divider 6. Arrows pointing towards the bottom 9 and the back rail Turn the cams to the right to fix bottom 9 and the back rail

12 Step 1.18 Place the sides and onto the bottom 9 and the back rail 11. ø15 x 10.5mm m x 8 Push cams into the holes indicated on the bottom 9 and the back rail 11. Arrows pointing towards the sides /. Turn the cams to the right to fix the sides and Step 1.19 Place the top 1 onto the sides and. ø15 x 10.5mm m x 9 Push cams into the holes indicated on the sides and. Arrows pointing towards the top 1. Turn the cams to the right to fix the top

13 Step 1.0 Place the front rail 10 onto the small diivider 6 as shown. ø15 x 10.5mm m x 1 Push cam into the hole indicated on the small divider 6. Arrow pointing towards the front rail 10. Turn the cams to the right to fix the sides and Step 1.1 Fix the angles Vl to the sides using screws Ko. See detail. Ko ø, x 9,5mm Screw x 10 Ko Ko

14 Step 1. Place one of the backs 7 into the rabbet on the top 1 and onto the post and the large divider 1. Important!! Make sure the angle between the top 1 and the post is 90 when the back 7 is attached. 1. x 15mm Nail x 18 stribute equally! 7mm from edge of vider! The back 7 must cover exactly half of the divider 5. Note the distance. stribute equally! Fix the back 7 to the top 1, the post and the back rail 11 using nails. Use a small hammer

15 Step 1. Place the backs 7 into the rabbet on the top 1 into the H-profile 8 and onto the post. ø x 1mm Screw x x 15mm Nail x 6 Fc Back fitting - 1 x 19mm x 6 Important!! Make sure the angle between the top 1 and the post is 90 when the backs 7 is attached. Fc Fc 8 Fc Fc Fc Fc 11 Fix the backs 7 to the top 1, the post and the back rail 11 using nails. Finally fix the backs 7 to the large divider 5 using screws through the back fittings Fc. stribute equally!

16 Step 1.! care. Important! The wardrobe is heavy. Lift with Its recommended that the wardrobe is fixed to the wall. Fh Wall strap and instruction x 1 Fr Shelf support x 8 ø5.8 x 8mm Screw x 8 Use the fittings Fh. Follow the instructions included with the fittings. Fix the shelf supports Fr to the side and the divider 5 using screws into the holes indicated. 1 Lower the shelves 1 onto the shelf supports Fr. Fr Fr 5 1 Fr Fr

17 Step Assembly of the drawers x Step.1 Fix the drawer sides 1 to the drawer back 15 as shown, using screws Bp. Bp ø x 5mm Screw x Bp Bp 1 1 x Step. Knock the dowels Ab into the holes indicated on the drawer sides 1 using a smal hammer. Ab ø6 x 0mm Wooden dowel x Ab Ab x

18 Step. Slide the drawer bottom 16 into the drawer sides x Step. Screw the bolts into the holes indicated on the drawer front 1. ø5 x 8, ccmm lt x 8 1 x Step.5 Push the drawer front 1 onto the drawer sides 1. ø15 x 10.5mm m x 8 Place cams into the holes indicated. Arrow pointing towards the front. Turn the cams to the right to fix the front x Step.6 Fi Important!! Make sure the angle between the drawer front 1 and the drawer sides 1 is 90 before the drawer bottom 16 is fixed using Fi as shown. To adjust the angle between the drawer sides and the fronts push the fitting Fi sidewards. See details. 1 1 Fi 16 Fi 15 Back fitting w. ø.5 x 15mm Screw x x Fi Fi Fi

19 Step.7 Ge Hd Fix the metal knobs Ge to the drawer front 1 using screws Hd. ø7 x mm Metal Knob x M x 0mm Screw x Ge 1 Hd x Step.8 Hk Pull out the drawer runners. Slide the drawers onto the runners. M x 9mm Screw x 8 Fit and fix the lower drawer first and work your way up. Fix drawers to the drawer runners using screws Hk. Hk Hk

20 Step Assembly of the doors. Door, left Door, center Door, right 18 Note! Two types of hinges is included. Type Me must be used on the center door and type must be used on the outer doors. Me Step.1 Place the two cup hinges Me into the holes indicated on the center door 17. ø x 1mm Screw x 18 Me ø6mm Cup hinge x Pd ø6mm Cup hinge x 5 x 1 x 1mm Magnet catch x6 Large Pd Small Pd Me Me 17 Door, right Pd 17 Door, center Place the four cup hinges into the holes indicated on the outer doors Door, left Pd Pd Fix the hinges using screws. Me Fix the magnet catches Pd using screws into the holes indicated. Pd

21 Step. Ge Hd Place the hanger rail 18 into the supports Fl. ø7 x mm Metal Knob x M x 0mm Screw x Slide the cup hinges Me / onto the crossplates Mc. Fix the hinges using the premounted screw in the crossplates. See details below on how to fit the cup hinge onto the cross plate Mc. 18 Me 18 Fl ! Mc Ge Hd Hd Ge Hd Ge! Mc Fix the metal knobs Ge to the doors 17 using screws Hd. Adjust the magnets Pc. Pc Pc

22 Step. Adjusting the doors left/right. a: To adjust the door towards the left hand side - turn the adjusting screw to the right. a: b: b: To adjust the door towards the right hand side - turn the adjusting screw to the left. Adjusting the doors forwards/backwards. a: Loosen the fixing screw. b: Push the cup hinges / the door forwards OR backwards to adjust. a: b: c: c: Tighten the fixing screws of ALL the crossplates. Adjusting the doors up/down. a: Loosen the two pre-mounted screws of each crossplate, BUT ONLY as much as it will allow the cross plate to move up and down. b: Push the the door up OR down to adjust. c: Tighten the pre-mounted screws of ALL the crossplates. a: b: c: If you need help or have damaged or missing parts, call the Argos Customer Helpline: Home Retail Group Avebury ulevard - xon Gate West - Central Milton Keynes MK9 NW