PET*STAR 4 OPERATOR MANUAL

Size: px
Start display at page:

Download "PET*STAR 4 OPERATOR MANUAL"

Transcription

1

2 Operator Manual Rev. 0 (PS - 4) PET*STAR 4 OPERATOR MANUAL Paragraph Page 1.0 INTRODUCTION INSTALLATION ALIGNMENT SPHERICAL ROLLER BEARING & PILLOW BLOCK OUTBOARD BEARING LUBRICATION CRANKSHAFT WEB DEFLECTION

3 Rev. 0 (PS - 4) Operator Manual 1.0 INTRODUCTION: The PETStar4 machines may be equipped with an Outboard bearing. The additional support of an outboard bearing is some times needed due to flywheel weight, power input, overhung load, or combination of all the above. The position of the outboard is critical to the drive side and pump side crankshaft main bearings with regards to horizontal and vertical alignment. 2.0 INSTALLATION: The outboard bearing arrangement consists of V sheave, Shaft Adapter, Pedestal, Pedestal sub base, Bearing Pillow block, double row spherical roller Bearings and back up plate as major components. The back up plate for the pillow block is included to provide a part (spacer) that can be removed for V-Belt installation, thus eliminating the requirement to remove Bearing pillow block from the Adapter shaft. On the installation of the 4 throw unit, the Pedestal will be sitting on a Pedestal sub base, which will be grouted to floor. This base will be about 12 high, six foundation bolts, cast into 12 floor, will be used to anchor the pedestal sub base. Use Epoxy grout to anchor the base firmly to the floor. See the General Arrangement drawings for the package. Shims are used to establish the level of the Pedestal, long and cross, between the top of the sub base and the bottom of the pedestal. The taper lock Sheave bushing fits to the V sheave, and will be assembled and tightened. There is a machine fit on the outboard side of the V sheave, which accommodates the adapter shaft. Bolts pass through the adapter shaft, and anchor in the V sheave. Once installed, the adapter shaft run out should be measured with dial indicator. It should be in the area of to not more than Shims placed between the bolting on stub shaft can be used to obtain alignment. 3.0 ALIGNMENT The following is a general guideline on method to be used to align the outboard bearing. The bearing is a double row spherical roller, self aligning and grease lubricated. It is locked onto the adapter shaft outside diameter from the V sheave by a taper bushing that is advanced on the shaft causing an expansion and corresponding internal clearance adjustment for the rollers. The to roller to race clearance is desired. The stabilizing ring is to be removed, thereby allowing the outer race within the pillow block to float with the compressor crankshaft axial float. 3

4 Operator Manual Rev. 0 (PS - 4) After the bearing and its taper lock spanner nut are adjusted and proper internal roller bearing clearance has been achieved, assemble the bottom and top halves of the outboard bearing pillow block and torque up the cap bolts holding top to bottom of the pillow block. 3.1 Clean and de burr or otherwise fit-up the top and bottom support surfaces of the outboard bearing support pedestal. 3.2 Remove all paint, grease or any other foreign material such that only bare metal is exposed for shim support. 3.3 Move the pedestal into position under the outboard bearing. 3.4 Shim the bottom of the pedestal to the pedestal frame such that about to remains between the pillow block and the top of the pedestal (after putting Spacer plate). (IMPORTANT : Shim stacks of more than thickness should be avoided, since by their thickness, they tend to become soft, and will crush a bit, leading to inaccurate support.) 3.5 Check the level of the top of the pedestal both parallel and perpendicular with the compressor using a machinists level graduated in increments. Figure 1 Outboard Bearing Assembly 4

5 Rev. 0 (PS - 4) Operator Manual 3.6 The top of pedestal should be level with centerline of the stub shaft within Adjust this level condition using steel shims or spacer plates between the bottom of the pedestal and the top to the pedestal frame. When level is achieved, bolt the bottom of the pedestal to the pedestal frame and torque the bolts to final assembled torque requirement. 3.7 Using a laminated shim pack, peel down enough shims to snugly fit under and support the pillow block. Assemble the bolts that attach the pillow block to the pedestal, leaving the bolts very loose, and not contacting the block. 3.8 Set a magnetic base dial indicator up with the magnetic base on the pedestal and the stylus of the indicator on any flat, horizontal surface of the pillow block that is parallel with the top surface of the pedestal (See Figure [1]). 3.9 Set the indicator to zero Torque the pillow block bolts to final assembled torque requirement Record the deflection of the pillow block as noted by the dial indicator. (IMPORTANT : If no deflection is measured, remove the shim pack from under the pillow block and peel off enough shims until some deflection is measured.) 3.12 Add a thickness of shims equal to the reading on the dial indicator. If the indicator showed movement of 0.010, add thickness of shims under the pillow block Reset the indicator as before, and re torque the pillow block bolts Record the deflection of the pillow block again, and again add sufficient shims to equal the deflection measured Retighten the cap bolts and re-measure deflection Continue this process until deflection measured is less than When the measured deflection in the fully torque condition is or less, loosens the assembly again and remove the shim pack completely. To the shim pack add 0.003, no more. Using a wedge, raise the pillow block slightly to allow insertion of the full shim pack with the just added Insert the bolts and torque to final assembled requirement Roll the machine over several revolutions by hand to assure free turning of the crankshaft Using appropriate taper dowel pins, set dowels in the base of the pedestal to the skid frame. Dowel the pillow block in the same manner, if appropriate. (Some pillow blocks are not Dowell able, due to the configuration of their cast bases) Reassemble the V-belts or other drive mechanism and make final adjustments Make a final check of the assembly by rolling over by hand. The machine should roll freely Lubricate the pillow block bearing with grease as required. 5

6 Operator Manual Rev. 0 (PS - 4) 4.0 SPHERICAL ROLLER BEARING & PILLOW BLOCK The pillow block bearing is double row spherical, self aligning bearing, grease lubricated. This type of bearing is of split construction for convenient assembly and disassembly. The Clearance between rollers to race that is desired can be obtained by tightening the taper lock spanner nut, which expands the inner race. A spherical roller bearing pillow block assembly is mounted on a straight shaft using a tapered bore bearing and adapter assembly. Adapter mount also permits maximum flexibility in the axial positioning of the bearing on the shaft and will accommodate light locational thrust loads. Adapter mounted spherical roller bearings require the correct removal of diametrical clearance from the bearing to prevent relative rotation between inner race and sleeve or shaft. Failure to employ proper mounting procedures can cause heating and reduce bearing performance. Figure 2 Exploded view of assembly spherical bearing pillow block 5.0 OUTBOARD BEARING LUBRICATION: The outboard bearing can be lubricated by grease. Apply the lubricant directly in the bearing between the rollers during the assembly. Place the grease into the lower half of the housing until it is approximately one third to one half full in general, only a good quality mineral grease should be used, having a melting point considerably higher than the operating temperature. A higher grease level can result in over heating. Use bearing grease 6

7 Rev. 0 (PS - 4) Operator Manual with an extreme pressure additive. The grease should be replaced after 3500 hours operation when the condition of the load and temperature are normal, or as the conditions dictate. 6.0 CRANKSHAFT WEB DEFLECTION Final alignment of the outboard bearing is determined by checking the crankshaft for deflection at the drive end. First web deflection is the amount of opening of the first crank web that occurs, as caused by an imposed side loads from the positioning of an outboard bearing, overhung load from V belt pull, or dead weight from V sheave. With V-belts tensioned, first web deflection should be measured. Remove any blocking from the crankshaft until the crank throw nearest the driver is pointing straight up in its top vertical position, and then measure the span between the crank webs as shown in the figure [3]. The micrometer shown consists of an ordinary inside micrometer barrel with pointed extension shaft of the proper length to measure the span between the webs. Punch a mark on the crank web with the center punch and encircle the same for future use. Insert a pointed end of the inside micrometer in the prick punch mark and adjust the barrel at the other end until, it will just pass the CLOSEST portion of the opposite web. Record the reading to the nearest thousands of an inch. FIG. 3 CHECKING DEFLECTION OF CRANKSHAFT WEB WITH MICROMETER Now rotate the crank approximately 180 so it points straight down and take another reading with the micrometer. Difference between the two readings represents the amount the crank webs deflected by the vertical misalignment of the out board bearing. If the reading with the crank in the upper position is less than the reading with the crank in the lower position, the outboard bearing is too low and must be raised enough so that there is no deflection between the crank up and the crank down position. To check horizontal alignment of the outboard bearing, set the Crank throw approximately horizontal, measure between webs as before and record the readings. Rotate the crank 180 and re-measure. Loosen bolts holding the outboard bearing, and move it sideways until the horizontal readings are the same. If all four readings are alike, the shaft is in perfect alignment. Every effort should be made to obtain this condition. 7

8 Operator Manual Rev. 0 (PS - 4) Before initial starting, recheck all leveling pads on the compressor, outboard bearing and driver and be sure that nuts on all foundation bolts are pulled down firmly. Make sure that all blocking is removed. The operation of the bearing should be checked during the initial run. Unusual noise should be investigated immediately and condition corrected. After the first day of the operation, the deflection at the first crank throw from the drive end should be rechecked. Although maximum difference between deflection measurement of (0.05 mm) is allowed at this throw, every attempt must be made to keep the deflection as close to 0 (zero) as possible by resetting the position of the out board bearing. The Compressor should be allowed to operate at the normal temperature at the short time before taking a final alignment check of the outboard bearing. After making any necessary readjustment to bearing portion, dowel the housing to the pedestal with a tapered dowel. The roller bearing pillow block is to be checked after initial 24 to 72 hours of operation to make certain that the locking device has not worked loose. Therefore, the locking device should be checked for proper tightness during periodic maintenance shutdown and retighten, if required using the spanner wrench. 8

RTI TECHNOLOGIES, INC.

RTI TECHNOLOGIES, INC. RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally

More information

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models -J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com

More information

INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT

INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT BACKGROUND Proper alignment of the transmission input shaft to the crankshaft centerline is required in order to achieve the best results

More information

General Four-Way Operation, Maintenance & Service Manual

General Four-Way Operation, Maintenance & Service Manual General Four-Way Operation, Maintenance & Service Manual SCOPE Included in the following pages you will find assembly drawings, exploded views, parts lists, assembly tips, operational descriptions and

More information

Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981

Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981 Page 1 of 12 Date: December 2, 1981 Subject: Models: Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System F-28C and 280C Effectivity: Helicopters manufactured prior to

More information

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing

More information

Additional Information

Additional Information NUMBER: 1 34 13 S.M. REF.: Listed in Table ENGINE: EPA04/07 Series 60 DATE: January 2013 SUBJECT: CHECKING CYLINDER LINER PROTRUSION ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section

More information

DODGE Grease Lubricated SPLIT-SPHER Roller Bearings and Pillow Blocks

DODGE Grease Lubricated SPLIT-SPHER Roller Bearings and Pillow Blocks Mounting Instructions For DODGE Grease Lubricated SPLIT-SPHER Roller Bearings and Pillow Blocks WARNING: Because of the possible danger to person(s) or property from accidents which may result from the

More information

WILCAP ADJUSTABLE ALIGNMENT PIN

WILCAP ADJUSTABLE ALIGNMENT PIN For correct installation of the Alignment pins the following tools will be needed; 1. Dial indicator and magnetic stand. 2. 1/4 or smaller drift and hammer. 3. Dial calipers. 4. 1/4 Allen wrench 5. 9/16

More information

Fig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7

Fig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7 FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track

More information

DRIVE COMPONENTS REMOVAL. 9. FXCW/C: see Figure Remove bolt (9), sprocket retainer (8), and thrust washer (7). NOTE PRIMARY DRIVE LOCKING TOOL

DRIVE COMPONENTS REMOVAL. 9. FXCW/C: see Figure Remove bolt (9), sprocket retainer (8), and thrust washer (7). NOTE PRIMARY DRIVE LOCKING TOOL DRIVE COMPONENTS REMOVAL PART NUMBER HD-7977 TOOL NAME PRIMARY DRIVE LOCKING TOOL S To remove the primary chain, remove compensating sprocket, clutch assembly and primary chain as an assembly:. Remove

More information

Thomas Disc Couplings Installation and Maintenance Series 71 Sizes (Page 1 of 11) DANGER!

Thomas Disc Couplings Installation and Maintenance Series 71 Sizes (Page 1 of 11) DANGER! Thomas Disc s Installation and Maintenance Series 71 s 150-1038 (Page 1 of 11) This is the Original Document in English Language Figure 1 - Thomas Series 71 1. General Information 1.1. Thomas Series 71

More information

Thomas Disc Couplings Installation and Maintenance Series 54RDG Sizes (Page 1 of 13) DANGER!

Thomas Disc Couplings Installation and Maintenance Series 54RDG Sizes (Page 1 of 13) DANGER! Series 54RDG Sizes 125-925 (Page 1 of 13) This is the Original Document in English Language Figure 1 - Thomas Series 54RDG Coupling 1. General Information 1.1. Thomas Series 54RDG Couplings are designed

More information

25000 Series Lo-T TM Butterfly Control Valve Instructions

25000 Series Lo-T TM Butterfly Control Valve Instructions November 2001 25000 Series Lo-T TM Butterfly Control Valve Instructions Instruction No. 25.1:IM PRELIMINARY STEPS Before installation, note the flow direction arrow on the valve body. The flow should enter

More information

Operating Instructions For Lockformer Button Punch Flanger

Operating Instructions For Lockformer Button Punch Flanger Capacity: 20 to 28 Gauge Galvanize Operating Instructions For Lockformer Button Punch Flanger To satisfactorily form the 90º button punch flange on light gauge materials, it was necessary to form the metal

More information

Thomas Disc Couplings Installation and Maintenance Type 54 RDG Sizes (Page 1 of 6)

Thomas Disc Couplings Installation and Maintenance Type 54 RDG Sizes (Page 1 of 6) Thomas Disc ouplings Installation and Maintenance Type 54 RDG Sizes 125-925 (Page 1 of 6) ATEX In order for this coupling to meet the ATEX requirements, it is mandatory to precisely follow these installation

More information

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions INTRODUCTION Congratulations! You are the owner of the finest rotary-style gasket cutter in the world. Originally developed and patented

More information

BEARING AND TYPES OF BEARING

BEARING AND TYPES OF BEARING BEARING AND TYPES OF BEARING In this article, you will learn about bearing and types of bearing. Generally, all types of machinery are provided with supports for rotating shafts, the supporting device

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: O-Ring Groove Cutter Adjustable Tool Block Upgrade Page 1 of 5 Prototype Kit Contents: 1x Adjustable Tool Block 1x Adjustable Tool Holder 1x Graduated Adjusting Screw 1x 1/8 Registration

More information

Thomas Disc Couplings Installation and Maintenance Series 71-8 Sizes (Page 1 of 10) DANGER!

Thomas Disc Couplings Installation and Maintenance Series 71-8 Sizes (Page 1 of 10) DANGER! Thomas Disc s Installation and Maintenance Series 71-8 s 225-750 (Page 1 of 10) This is the Original Document in English Language Figure 1-1. General Information Thomas Series 71-8 1.1. Thomas Series 71-8

More information

A-PDF Split DEMO : Purchase from to remove the watermark SHAFT DRIVE

A-PDF Split DEMO : Purchase from  to remove the watermark SHAFT DRIVE SHAFT DRIVE 4-1 A-PDF Split DEMO : Purchase from www.a-pdf.com to remove the watermark SHAFT DRIVE CONTENTS SECONDARY BEVEL GEARS... 4-2 CONSTRUCTION... 4-2 REMOVAL... 4-4 DISASSEMBLY... 4-4 INSPECTION...

More information

Inventory MODEL T10096 TAPER ATTACHMENT FOR G0509 & G0509G LATHE INSTRUCTIONS. Inventory (Figure 1) Needed Items

Inventory MODEL T10096 TAPER ATTACHMENT FOR G0509 & G0509G LATHE INSTRUCTIONS. Inventory (Figure 1) Needed Items MODEL T10096 TAPER ATTACHMENT FOR G0509 & G0509G LATHE INSTRUCTIONS Inventory The Model T10096 taper attachment was carefully packed when it left our warehouse. If you discover it is damaged after you

More information

ELECTRIC TOOL CORPORATION

ELECTRIC TOOL CORPORATION Cat. No. -0 / Hex Demolition Hammer Cat. No. 0-0 Spline Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 -9-00 d 000 -9-00 d SpecialTools Require Forcing discs

More information

BBF Series Blower Base Frame Assembly Instructions Rev.: BFA-9105

BBF Series Blower Base Frame Assembly Instructions Rev.: BFA-9105 BBF Series Blower Base Frame Assembly Instructions Rev.: BFA-9105 These assembly instructions are to be used as a general reference guide to facilitate assembly. Please consult the blower, bushing, sheave,

More information

Type XTSR71 Sizes

Type XTSR71 Sizes (Page 1 of 13) s 494-5258 Type XTSR71 s 494-5258 Figure 1 Thomas XTSR71 Coupling 1. General Information 1.1 Thomas Couplings are designed to provide a mechanical connection between the rotating shafts

More information

PEDESTAL OVERHAUL. Some of the tools for a pedestal overhaul. Pedestal work stand

PEDESTAL OVERHAUL. Some of the tools for a pedestal overhaul. Pedestal work stand INTRODUCTION A properly greased labyrinth seal will help prevent dust and water damage to the pedestal bearing oil supply and shaft seal area. Properly greased and oiled pedestals rarely require an overhaul.

More information

1 of 12 5/24/2015 9:43 AM

1 of 12 5/24/2015 9:43 AM 1 of 12 5/24/2015 9:43 AM REAR PROPELLER SHAFT ASSEMBLY Components REMOVAL 1. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY 2 of 12 5/24/2015 9:43 AM a. Place match marks on the propeller shaft flange

More information

LocoGear. Technical Bulletin - 02 January 11, by LocoGear LIVE STEAM CASTINGS. Tech Bulletin - 02

LocoGear. Technical Bulletin - 02 January 11, by LocoGear LIVE STEAM CASTINGS. Tech Bulletin - 02 LIVE STEAM CASTINGS Tech Bulletin - 02 LocoGear Technical Bulletin - 02 January 11, 2003 2003 by LocoGear John D.L. Johnson 3879 Woods Walk Blvd. Lake Worth, FL 33467-2359 jjohnson@locogear.com www.locogear.com

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: O-Ring Groove Cutter Page 1 of 6 Kit Contents: 1x Cutter Head Assembly with Handle & Adjustable Tool Block 1x Graduated Adjusting Screw 1x Adjustable Tool Holder 1x Carbide Insert (Size of

More information

Operating Instructions

Operating Instructions Operating Instructions Holding the material against the angle gauge slide it into the forming head. Be sure that the material remains against the gauge until work is finished. NOTE: This machine will handle

More information

Geology, Prospectors, Mining, Metallurgy, Assaying, Environmental, Geotechnical

Geology, Prospectors, Mining, Metallurgy, Assaying, Environmental, Geotechnical LEGEND INC. Geology, Prospectors, Mining, Metallurgy, Assaying, Environmental, Geotechnical 988 Packer Way Sparks, NV 89431 Tel: (786) 786-3003 Fax: (775) 786-3613 Email: info@lmine.com Web: www.lmine.com

More information

MODEL 36 Di-Acro Hand Shear

MODEL 36 Di-Acro Hand Shear OPERATOR S MANUAL & INSTRUCTIONS MODEL 36 Di-Acro Hand Shear Di-Acro, Incorporated PO Box 9700 Canton, Ohio 44711 3713 Progress Street N.E. Canton, Ohio 44705 330-455-1942 330-455-0220 (fax) Revised 01/02

More information

INSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON RED WING LATHE

INSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON RED WING LATHE DENTAL, INC. TECHNICAL BULLETIN Q824-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427 SAVE THIS FOR FUTURE REFERENCE www.wellsdental.com

More information

Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A. Ref Rev.C General Pump is a Member of The Interpump Group

Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A. Ref Rev.C General Pump is a Member of The Interpump Group MK Repair Manual MK40A-MK45A-MK50A MK55A-MK60A-MK65A General Pump is a Member of The Interpump Group 8 INDEX 1. INTRODUCTION..................................................Page 3 2. REPAIR INSTRUCTIONS...........................................Page

More information

DO35 MAINTENANCE INSTRUCTIONS

DO35 MAINTENANCE INSTRUCTIONS CUSTOMER INFORMATION SHEET NO. 038 DO35 MAINTENANCE INSTRUCTIONS (DO35 V3 LAUNCHED PRODUCTION JUNE 2017) Table of Contents 1.0 Replacing Spindle Bushes V3... 22 2.0 Replacing Locking Mechanism V3... 6

More information

ESA-300 Full Breakout

ESA-300 Full Breakout Interior View 0 Installation Instructions For use with ESA II Controler DORMA AUTOMATICS, Inc. 94 Sherwood Drive Toll-Free: 877-67-6 DL844-00 Lake Bluff, IL 60044 Fax: 877-4-7999 Rev. /07 Tools Required:

More information

YALE FIGURE 500 & 500R CLOSURE OPERATION AND MAINTENANCE INSTRUCTIONS

YALE FIGURE 500 & 500R CLOSURE OPERATION AND MAINTENANCE INSTRUCTIONS YALE FIGURE 500 & 500R CLOSURE OPERATION AND MAINTENANCE INSTRUCTIONS IMPORTANT INFORMATION Note To Supervisor: Please share this information with your employees and make sure they have received training

More information

SAFETY INSTRUCTIONS. Wear protective clothing, including safety glasses and steel toe boots.

SAFETY INSTRUCTIONS. Wear protective clothing, including safety glasses and steel toe boots. SAFETY INSTRUCTIONS Wear protective clothing, including safety glasses and steel toe boots. DO NOT allow loose clothing or long hair near machine operations. Keep work site and machine clean. Use brush

More information

INSTRUCTIONS

INSTRUCTIONS IMPORTANT: THIS IS A HIGH PERFORMANCE PART AND IMPROPER INSTALLATION COULD RESULT IN INJURY OR DEATH! NEVER WORK UNDER AN AUTOMOBILE THAT IS NOT PROPERLY SUPPORTED AND BLOCKED FROM ROLLING. NO CREDIT OR

More information

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO 47(5x) 46 45 00 44 0 59 43 42 84 51 57 46 47 48 59 83 64 77 48 47(2x) 49(2x) 40 58 See service note on page 5 41 82 51 40 41 42 43 44 45 87 52 27 28 34 57 29 (6x) 60 28 EXAMPLE: Component Parts (Small

More information

HDL(M)6 Nut/Screw Assembly

HDL(M)6 Nut/Screw Assembly HDL(M)6 Nut/Screw Assembly Remove, repair, and reassemble the nut and screw assembly in your HDL series double lock vise. In these instructions when we refer to the front of the vise or nut/screw assembly,

More information

Installation Instructions

Installation Instructions The IMS ETERNAL FIX PATENT PENDING Installation Instructions EPS recommends professional installation for the Eternal IMS Fix. Please take all precautionary safety measures. We also recommend putting the

More information

The Virgo/Libra Steam Engine

The Virgo/Libra Steam Engine The Virgo/Libra Steam Engine Congratulations on becoming the owner of a Virgo or Libra Steam Engine. With careful use and maintenance it will give many years of satisfying performance. Contents 1) Notes

More information

AFB (AIR FAN BEARING) INSTALLATION GUIDE

AFB (AIR FAN BEARING) INSTALLATION GUIDE 654 AFB (AIR FAN BEARING) INSTALLATION GUIDE AFB PARTS Bearing Housing - Secured together with two 3/8 x 1.25 in. Cap Screws Black Wiper Seals - Secured together with O-ring cord (Subsequently depicted

More information

Electric Skein Winder

Electric Skein Winder Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers

More information

Removing Right-Side. Components. Right-Side. Components. Click Here to Go Back AT THIS POINT

Removing Right-Side. Components. Right-Side. Components. Click Here to Go Back AT THIS POINT Click Here to Go Back NOTE: There is an oil passage beneath the driven gear/drive gear assembly. This passage should be plugged prior to removing the driven gear and drive gear. Failure to do so could

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS

FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.

More information

4.4 PUMP MAINTENANCE MODELS: DB, DC, DF, DG, DJ, DL

4.4 PUMP MAINTENANCE MODELS: DB, DC, DF, DG, DJ, DL 4.4 PUMP MAINTENANCE MODELS: DB, DC, DF, DG, DJ, DL 4.4.1 EXPLODED VIEW DRAWING REF. QTY. DB DC DF DG DJ DL DESCRIPTION PART # 1 1 ADAPTOR FRAME 034007 2 12 LOCK WASHER 3/8 x 1/8 S.S. 034004 3 12 HEX HEAD

More information

Inventory MODEL H7937 TAPER ATTACHMENT FOR THE G0600 LATHE INSTRUCTIONS. Inventory (Figure 1) Needed Items

Inventory MODEL H7937 TAPER ATTACHMENT FOR THE G0600 LATHE INSTRUCTIONS. Inventory (Figure 1) Needed Items MODEL H7937 TAPER ATTACHMENT FOR THE G0600 LATHE INSTRUCTIONS Inventory The Model H7937 taper attachment was carefully packed when it left our warehouse. If you discover it is damaged after you have signed

More information

DODGE Adapter Mounted DODGE USAF 500/600 Series Pillow Blocks

DODGE Adapter Mounted DODGE USAF 500/600 Series Pillow Blocks DODGE Adapter Mounted DODGE USAF 500/600 Series Pillow Blocks These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of printing.

More information

ICU TRACKLESS SLIDING DOOR

ICU TRACKLESS SLIDING DOOR Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and #4 screws Wrenches / Sockets

More information

Bearing Overhaul Instructions for: Nickel (0.1) and Butcher (0.1) a) Using a 6mm Allen wrench, remove the two bolts attaching the shock.

Bearing Overhaul Instructions for: Nickel (0.1) and Butcher (0.1) a) Using a 6mm Allen wrench, remove the two bolts attaching the shock. Bearing Overhaul Instructions for: Nickel (0.1) and Butcher (0.1) 2010 Tools Needed: 6902/7902/7900 Press Tool 6902 Removal Tool 7902 Bearing Removal Tool 7900 Removal Tool (2) ll/16" or adjustable wrenches

More information

Model: SCD430 SCD640. Installation & Operation Guide P/N SCD640-95

Model: SCD430 SCD640. Installation & Operation Guide P/N SCD640-95 Model: SCD430 SCD640 Installation & Operation Guide P/N SCD640-95 Model SCD430 and SCD640 Kurt has two Self-Centering vises, a four-inch jaw width (SCD430) and a six-inch jaw width (SCD640). Jaw opening

More information

Di-Acro 36 Power Shear

Di-Acro 36 Power Shear OPERATOR S MANUAL & INSTRUCTIONS Di-Acro 36 Power Shear Di-Acro, Incorporated PO Box 9700 Canton, Ohio 44711 3713 Progress Street N.E. Canton, Ohio 44705 330-455-1942 330-455-0220 (fax) Revised 01/02 Sale

More information

HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet

HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet Read the enclosed instructions and recommendations before any installations CONTENTS Dead-Length Collet Adaptation

More information

2. Inspect the end yoke bores for wear and damage. Replace if necessary.

2. Inspect the end yoke bores for wear and damage. Replace if necessary. SERVICE INSTRUCTIONS BEFORE DOING ANY SERVICE OR MAINTENANCE WORK ON THE MACHINE, YOU MUST: Disengage all power Shut off the tractor engine LOOK and LISTEN! Make sure all moving parts are stopped. Disconnect

More information

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward.

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward. Figure 1 Miniature Quick Change Applicators, of the end feed type, are designed to crimp end feed strip terminals to prestripped wires. Each applicator is set up to accept the strip form of certain specific

More information

HAND SHEARS NO. 12 AND NO. 24

HAND SHEARS NO. 12 AND NO. 24 OPERATOR S MANUAL & INSTRUCTIONS HAND SHEARS NO. AND NO. Di-Acro, Incorporated PO Box 9700 Canton, Ohio 7 7 Progress Street N.E. Canton, Ohio 70 0--9 0--00 (fax) Revised 0/0 Sale or distribution of manuals

More information

meaden New Generation Tooling & Operations Manual

meaden New Generation Tooling & Operations Manual 06-19-01 New Generation Tooling & Operations Manual 210 West 83rd Street Burr Ridge, Illinois 60527 Telephone: 630/655-0888 FAX: 630/655-3012 www.printing.com INTRODUCTION Table of Contents I. ENGAGEMENT

More information

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems

More information

ITEM NO. PART NO DESCRIPTION QTY.

ITEM NO. PART NO DESCRIPTION QTY. PUMP MAINTENANCE ITEM NO. PART NO DESCRIPTION QTY. 1 52002 Center Case 1 2 52052 Back End Plate 1 3 52051 Front End Plate 1 4 55090 Octagonal Nut 1 5 53001 Idler Gear 1 6 53002 Drive Gear 1 7 28062 Bushing

More information

NUMBER: S.M. REF.: Listed in Table ENGINE: Series 50/50G DATE: October 2013 SUBJECT: MACHINING CYLINDER BLOCK COUNTERBORES

NUMBER: S.M. REF.: Listed in Table ENGINE: Series 50/50G DATE: October 2013 SUBJECT: MACHINING CYLINDER BLOCK COUNTERBORES NUMBER: 10 25 13 S.M. REF.: Listed in Table ENGINE: Series 50/50G DATE: October 2013 SUBJECT: MACHINING CYLINDER BLOCK COUNTERBORES ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section

More information

MSR/MSB Mechanical Setting Tool

MSR/MSB Mechanical Setting Tool Tech Unit No: 0620000004 Revision: B Approved By: Quality Engineer Date: 2014-12-16 MSR/MSB Mechanical Setting Tool FEATURES: Special designed Bow Spring provides positive control and allows one size Mechanical

More information

Inspection. Assembly Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent.

Inspection. Assembly Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent. 6010-34 Inspection 3. Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent. 3. If spring test equipment is available, check the tension of each spring according to the specifications

More information

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extention Sections. Reliable Connections

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extention Sections. Reliable Connections insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extention 2-3 Improved Fire Hydrant Inserting Extention

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: Lifter-Tru Kit for Ford Windsor & SVO Small Block V8 Page 1 of 5 Kit Contents: 2x End Plates 2x 5/8 Threaded Adjustment Sleeves 1x Front Angle Bracket 2x 5/8 Adjustment Sleeve Spacers * 1x

More information

Fisher 667 Diaphragm Actuators Size 80 and 100

Fisher 667 Diaphragm Actuators Size 80 and 100 Instruction Manual 667 Size 80 and 100 Actuators Fisher 667 Diaphragm Actuators Size 80 and 100 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Maximum Pressure Limitations...

More information

Click Here to Go Back

Click Here to Go Back Click Here to Go Back Fig. -94 Fig. -97 CC42D 10. Remove the cap screw securing the gear shift stopper plate pin retainer; then remove the retainer. Fig. -95 CC45D 12. Remove the link arm and account for

More information

.00025" PER CLICK. As you turn the adjustment screw you should be able to feel a click. Each click will change the part diameter.00025".

.00025 PER CLICK. As you turn the adjustment screw you should be able to feel a click. Each click will change the part diameter.00025. ULTRA PRECISION DIAMETER ADJUSTMENT.00025" PER CLICK The ultra precision diameter adjustment is extremely accurate, as well as, quick and easy to use. The adjustment mechanism is spring loaded to take

More information

400GTO Lubrication Guide

400GTO Lubrication Guide 400GTO Lubrication Guide Lubrication Guidelines for the following equatorial mounting: 400GTO Servo with GTOCP2 or CP3 Controller For other 400 models please review other postings as they become available.

More information

Installation Instructions

Installation Instructions Installation Instructions XLC Series Self-aligning split bearing Experience In Motion 1 Equipment Check 1.1 Follow plant safety regulations prior to equipment disassembly: Lock out motor. Wear designated

More information

Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions

Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips

More information

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems with A/C #13600 / #13620

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems with A/C #13600 / #13620 Small Block Ford 289 / 302 / 351W / 5.0 Installation Manual For Systems with A/C #13600 / #13620 Billet Specialties, Inc. 500 Shawmut Avenue. La Grange, Illinois 60526 Tech Line (708) 588-0505 Fax (708)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last

More information

OPERATING INSTRUCTIONS AND PARTS LISTS

OPERATING INSTRUCTIONS AND PARTS LISTS 3889560 REEL ALIGNMENT GAGE OPERATING INSTRUCTIONS AND PARTS LISTS WARNING You must thoroughly read and understand this manual before operating the equipment, paying particular attention to the Warning

More information

SERVICE MANUAL AND PARTSLIST

SERVICE MANUAL AND PARTSLIST SERVICE MANUAL AND PARTSLIST Next 20 CONTENTS WHAT TO DO WHEN... 1~3 SERVICE ACCESS FACE COVER... 4 TOP COVER... 4 BASE COVER... 5 REAR COVER... 6 FRONT COVER... 7 MECHANICAL ADJUSTMENT NEEDLE THREAD TENSION...

More information

TO OPERATE AUTO-GUIDE POWER. 24 Gauge Pittsburgh Operating Instructions FLANGING ATTACHMENT

TO OPERATE AUTO-GUIDE POWER. 24 Gauge Pittsburgh Operating Instructions FLANGING ATTACHMENT 24 Gauge Pittsburgh Operating Instructions Holding the material against the angle gauge slide it into the forming head. Be sure that the material remains against the gauge until work is finished. Make

More information

Installation Instructions

Installation Instructions Installation Instructions XLC Generation 2 Self-aligning split bearing Experience In Motion 1 Equipment Check 1.1 Follow plant safety regulations prior to equipment disassembly: Lock out motor. Wear designated

More information

HOW TO MEASURE AND FIT REPLACEMENT TRUNNION ROLLERS

HOW TO MEASURE AND FIT REPLACEMENT TRUNNION ROLLERS HOW TO MEASURE AND FIT REPLACEMENT TRUNNION ROLLERS When Customers order trunnion rollers for their Double Arm (DA) mixers they may not be aware that these rollers need to be custom fit to their mixer.

More information

Slab rollers Guion Road Indianapolis, Indiana USA (800) Fax: (317)

Slab rollers Guion Road Indianapolis, Indiana USA (800) Fax: (317) Slab rollers 6060 Guion Road Indianapolis, Indiana 46254-1222 USA (800) 374-1600 Fax: (317) 248-9300 www.amaco.com Dear Customer, We hope you enjoy your new brent slab roller. Many different people are

More information

Procedure for Wrench Calibration and Snug Tightening

Procedure for Wrench Calibration and Snug Tightening Procedure for Wrench Calibration and Snug Tightening 1. Scope: This procedure provides the method for calibration of a manual torque wrench or an adjustable impact wrench and the snug tightening procedure

More information

Instruction Manual for DODGE SLEEVOIL RXT Pillow Blocks With External Circulating Oil Lubrication

Instruction Manual for DODGE SLEEVOIL RXT Pillow Blocks With External Circulating Oil Lubrication Instruction Manual for DODGE SLEEVOIL RXT Pillow Blocks With External Circulating Oil Lubrication These instructions must be read thoroughly before installation or operation. CAUTION: Do not scrape, rebabbit,

More information

Chiltern Model Steam Engines

Chiltern Model Steam Engines Chiltern Model Steam Engines Mill Twin Cylinder Model Steam Engine v2 Assembly Instructions v1.0 Notes: 1. In overview the engine should first be assembled "dry" with no oil/lubricants, thread lock or

More information

Frameless Inline Door With Return QCI5263

Frameless Inline Door With Return QCI5263 INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges

More information

001-Component-build. Build the following Contraptor components before assembly:

001-Component-build. Build the following Contraptor components before assembly: 001-Component-build Build the following Contraptor components before assembly: http://www.contraptor.org/make-linear-rail-v2#assembly http://www.contraptor.org/make-linear-bearings-v2#assembly http://www.contraptor.org/make-sliding-elements#assembly

More information

Taper Attachment for G4016 Gear Head Lathe

Taper Attachment for G4016 Gear Head Lathe Taper Attachment for Gear Head Lathe MODEL H0775 INSTRUCTION SHEET COPYRIGHT AUGUST, 2004 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE

More information

Instructions for the installation of Ellison Bronze balanced door models #137 & 138

Instructions for the installation of Ellison Bronze balanced door models #137 & 138 1. A packing list will be found in crate No. 1 of each shipment. The parts in the crates should be checked with this list. If there is any discrepancy, notify Ellison Bronze at once. 2. All parts are numbered.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS THESE INSTRUCTIONS COVER THE INSTALLATION OF THE FOLLOWING REAR DOORS WITH OUTSIDE CABLES AND MAXIMUM SECURITY LOCK: 3/4" DryFreight 1-1/8" PolarGuard

More information

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems without A/C #13605 / #13625

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems without A/C #13605 / #13625 Small lock Ford 289 / 302 / 351W / 5.0 Installation Manual For Systems without /C #13605 / #13625 illet Specialties, Inc. 500 Shawmut venue. La Grange, Illinois 60526 Tech Line (708) 588-0505 Fax (708)

More information

Brother Industries, Ltd. Nagoya, Japan

Brother Industries, Ltd. Nagoya, Japan 4. 2001. This service manual has been compiled for explaining repair procedures of the MODEL XL-6562, XL6452, XR- 46. This was produced based on up-to-date product specifications at the time of issue,

More information

MODELS 49 RA 49 RAZ 49 RAC

MODELS 49 RA 49 RAZ 49 RAC General Safety and Maintenance Manual MODEL grinder featuring a rear exhaust. Model Number Exhaust Direction REAR Throttle Type (L) Lever or (K) Safety Lever Speed 12000 to 14000 R.P.M (13500rpm is standard)

More information

TOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill

TOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24

More information

MKS. MKS Series MKS 40 MKS 45 MKS 50 MKS 55 MKS 60 MKS 65. Repair Manual

MKS. MKS Series MKS 40 MKS 45 MKS 50 MKS 55 MKS 60 MKS 65. Repair Manual MKS Series MKS 40 MKS 45 MKS 50 MKS 55 MKS 60 MKS 65 Repair Manual INDEX. INTRODUCTION 3 2. REPAIR INSTRUCTIONS 3 2. Crank Mechanism Repair...3 2.. Crank Mechanism Disassembly...4 2..2 Crank Mechanism

More information

Smart Sifter Vertical Shaft & Splined Coupler Replacement Manual

Smart Sifter Vertical Shaft & Splined Coupler Replacement Manual Smart Sifter Vertical Shaft & Splined Coupler Replacement Manual Company: Norvell Company Inc. Phone: 800-653-3147 Fax: 620-223-3115 Date: Sept. 2014, Rev. #2 This manual is for our customers who wish

More information

BRAVO STERN DRIVE 3 C BRAVO ONE

BRAVO STERN DRIVE 3 C BRAVO ONE RAVO STERN DRIVE 3 C 22439 RAVO ONE Table of Contents Page Specifications............................... 3C-1 Torque Specifications..................... 3C-1 Preloads................................ 3C-1

More information

00108/00110 INSTRUCTION MANUAL

00108/00110 INSTRUCTION MANUAL 00108/00110 INSTRUCTION MANUAL Removable and Adjustable Mudflap System IMPORTANT! Exhaust Systems Note: Any modifications to the factory installed exhaust system may void your manufacturer s warranty.

More information

Maintenance Information

Maintenance Information 16601023 Edition 2 January 2014 Air Impact Wrench 2705P1 Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub

Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub INSTALLATION MANUAL Hudson Tuf-Lite and Tuf-Lite II fan blades Adjustable Pitch Fan Assembly 15 thru 20 Diameter Hudson Tuf-Lite (black) fan blades are made

More information