Installation manual. novotegra for tiled roofs

Size: px
Start display at page:

Download "Installation manual. novotegra for tiled roofs"

Transcription

1 Installation manual novotegra for tiled roofs I

2 TABLE OF CONTENTS 1 Information Installation system maintenance novotegra for tiled roofs System components, tools and work equipment Required for installation Installation system components installation variants Installation system components optional Installing the substructure Installing the roof hooks Installing the rails Installing the module Installation variants Warranty / product liability and disclaimer II

3 1 Information Safety information Installation work may only be carried out by qualified expert personnel. Safety clothing in accordance with the relevant national regulations and guidelines must be worn during all work. Installation must be carried out by at least two people so as to ensure that help is available in the event of an accident. All relevant nationally and locally valid occupational safety regulations, accident prevention regulations, standards, construction regulations and environmental protection regulations must be observed, along with all regulations of the institutions for statutory accident insurance and prevention. National regulations for working at height or on roofs must be complied with. Electrical work must be carried out in compliance with nationally and locally valid regulations and guidelines and in accordance with the safety regulations for electrical work. The earthing / potential equalization of the installation system must be carried out in line with the nationally and locally valid standards and guidelines. Classification into hazard classes In order to draw the user's attention to potentially hazardous situations, the following hazard classes are used, based on ANSI Z 535. The hazard class describes the risk in the event that the safety information is not observed. Warning symbol with signal word Hazard class as per ANSI Z 535 DANGER! indicates an immediate hazard. Failure to prevent this could result in death or severe injury. WARNING! indicates a potential hazard. Failure to prevent this could result in death or severe injury. CAUTION! indicates a potential hazard. Failure to prevent this could result in slight or minor injury. NOTICE! indicates a potentially damaging situation. Failure to prevent this could result in damage to the system or something in its environment. General information The product must be checked for completeness upon receipt using the accompanying delivery notice. BayWa r.e. Solarsysteme GmbH shall assume no costs or guarantees for any subsequent deliveries by express delivery if missing material is only noticed during installation. The installation system is suitable for securing PV modules with standard market dimensions. The maximum permitted module width is 1.34 m. The suitability of the installation system for the respective project must be checked on an individual basis with respect to the existing roof covering / roof construction. The roof covering / roof construction must meet the requirements of the installation system in terms of loadbearing capacity, load-bearing structure and condition. Requirements for the material used in roof construction or roof covering: Wooden components (rafters/purlins): minimum strength class C24, no fungal infestation or rot Tensile strength Rm,min of trapezoidal panels: steel 360 N/mm²; aluminium 195 N/mm² 1

4 The user must test the load-bearing capacity of the existing roof / roof construction (rafters, purlins, trapezoidal panels, number of fasteners for folded seam roof, etc.) or have this tested. The user must take into account structural issues with regard to insulation penetrations (e.g. condensation). Installation instructions The components of the novotegra installation system are intended solely for securing PV modules. Depending on the roof type of the building, installation system components that are suitable for this roof type must be used. Strict compliance with the safety and installation instructions in this manual is required for compliance with the intended use of the novotegra installation system. All claims for warranty, guarantee and liability against the manufacturer are rendered null and void in the event of non-intended use and non-compliance with the safety and installation instructions, non-use of associated installation components or use of third-party components not belonging to the installation system. The user shall bear liability for damages and resulting consequential damages to other components such as PV modules or to the building itself, as well as for injury to persons. The constructor must read the installation manual prior to installation. Any open questions must be resolved with the manufacturer prior to installation. The installation sequence described in this manual must be complied with. Please ensure that a copy of the installation manual is kept in the immediate area of the works on the construction site. The assembly instructions (module loading, fastening, clamping ranges, etc.) of the module manufacturer must be observed and complied with. Prior to installation, structural analysis for the installation system must be carried out with the loads foreseen for the project in accordance with national standards. Information relevant to the installation (e.g. distance between roof hooks, screw lengths, overhangs and protrusions) is determined by the structural analysis carried out using the Solar-Planit.de design software. The permitted roof incline for use of the installation system in accordance with this installation manual is 0 to 60 degrees. Two module support rails must be installed symmetrically beneath each module in order to transfer the load evenly to the substructure. The specified tightening torque values must be observed and tested on a random basis on site. Information on structural analysis The installation system must always be calculated for each project individually using the Solar-Planit.de design software. The structural analysis determines only the load-bearing capacity of the novotegra installation system and also takes fastening to the building (rafters, purlins, trapezoidal panel, etc.) into account. The load transfer within the building is not taken into account (structural analysis of existing building). The load-bearing capacity of the installation system components is determined here based on the planned module arrangement and the relevant roof data (project data collection). On-site deviations from the planning may lead to different results. The load assumptions (load and roof partitioning) are made on a country-specific basis according to the specifications of the load standards in the Eurocode. In Switzerland, the loads to be applied are determined according to SIA 261. The modules may not be installed above the bargeboard, ridge or eaves (increased wind load). The modules may only be mounted up to a notional horizontal line with the ridge tile at the ridge and no further than flush at the bargeboard. In the area around the eaves, the modules may only be installed up to the end of the roof covering for load-bearing reasons. If the building is at an exposed location (e.g. exposed to wind load on a slope) or in the event of snow accumulation (e.g. dormer or roof snow fence), the user must take responsibility for observing the specifications in the load standards of the Eurocode or SIA 261 (Switzerland). The design software does not take these cases into account. 2

5 The structural analysis of the installation system is based on the modules being symmetrically mounted on the installation rails on the long side of the modules in order to evenly distribute the load onto the substructure. The results calculated using the design software such as the distances between the fastening equipment (e.g. roof hooks, hanger bolts, seam clamps, etc.), the rail lengths and quantity of fastening equipment (e.g. direct fastening on trapezoidal panel), overhangs (e.g. protruding rails or roof hooks) as well as the further calculation information must be observed and complied with. novotegra is tested and certified by MCS: 2 Installation system maintenance The installation system must be tested annually for stability and proper functioning. In addition to visually inspecting the components and the roof covering for damage, all screw connections must also be checked. Components can be removed by following the work steps detailed below in the reverse order. Maintenance work must be carried out by a specialist company with verifiable experience of electrical systems and working with installation systems. 3 novotegra for tiled roofs The contents of this installation manual describe the installation of the substructure on roofs with clay tiles, concrete roof tiles or plain tiles roofing. These installation steps can also be used likewise for installation on roofs with slate roofing. In this case, however, covers or lead flashings must be fitted in the area where the roof hooks protrude from the roof in order to prevent water penetration. Please contact us before carrying out this kind of installation so that we can provide customer support to you. 3

6 4 System components, tools and work equipment 4.1 Required for installation Image Tool Component* Product group Roof hook set Material: V2A and aluminium Tool: Special socket 18 mm, deep Roof fasteners and fastening equipment Roof hook fastening screw Material: Galvanized steel or V2A Tool: Bit Torx TX 25 Roof fasteners and fastening equipment C-rail Material: Aluminium Module support rail Rail connector set Material: Aluminium and V2A Tool: Special socket 18 mm, deep Centre clamp set Material: Aluminium, cast aluminium and V2A Tool: Socket 8 mm End clamp set Material: Aluminium, cast aluminium and V2A Tool: Socket 8 mm Anti-slide protector set Material: V2A Module support rail Module fasteners Module fasteners Module fasteners * The components vary depending on the requirements of the roof, the structural analysis and the choice of components and may deviate from the images above. Image Work equipment Cordless screwdriver Torque key up to at least 50 Nm Torque key up to at least 12 Nm Use for tool Bit Torx TX 25 Socket 8 mm Special socket 18 mm, deep Socket 8 mm Use Component connections, clamp assembly Rail assembly Clamp assembly Chopsaw --- Cutting rails Angle grinder --- Work on tiles Bit extension Bit Torx TX 25 Roof hook assembly 4

7 4.2 Installation system components installation variants Image Tool Component** Product group Cross rail connector set Material: Cast aluminium and V2A Tool: Special socket 18 mm, deep Roof fasteners and fastening equipment Floating bearing set* Material: Aluminium and V2A Tool: Special socket 18 mm, deep Anti-slide protector for horizontal installation Material: Aluminium and V2A Tool: Special socket 18 mm, deep Module support rail Module fasteners ** Required components depending on construction of substructure (e.g. cross rail configuration), system expansion (e.g. using floating bearings) or module arrangement (e.g. horizontal module installation). 4.3 Installation system components optional Image Tool Component*** Product group Cover cap for C-rail Material: Aluminium and V2A Tool: Special socket 18 mm, deep Optional items Cover for C-rail 2,000 mm Material: Aluminium Optional items Earthing connection 18 mm set Material: V2A Tool: Special socket 18 mm, deep Optional items Self-locking cable ties Optional items Cable clip d = 10 mm Optional items *** Optionally available installation system components, e.g. for improving the aesthetics of the system, cable routing or earthing of the installation system. 5

8 5 Installing the substructure Prior to installation, the module array must be measured out on the roof and the position of the fastening equipment (e.g. roof hooks, hanger bolts, seam clamps, etc.) determined, taking the structural analysis into account. The individual installation steps for vertical module installation are described below. References are made to installation variants (IV) for the various design possibilities. The associated work steps are described at the end. 5.1 Installing the roof hooks Exposing the rafters Expose the rafters by removing the tiles. Scaffolding must be constructed in accordance with the relevant regulations. Positioning the roof hook Insert the roof hook so that the hook lies in the trough of the roof tile. The position of the roof hook on the rafter must be determined taking into account the structural specifications (IV 4). Mark the roof tile and the tile beneath (if present) at the point where the roof hook protrudes. For plain tile roofing, proceed according to IV 2 + IV 3. Recessing the tile Grooved tile roof / concrete roof tile: Carefully cut a recess in the area where the roof hooks protrudes using an angle grinder. Recess: notched or continuous Plain tile: Cut the recess either continuously along the side or else notched to fit the thickness of the hook. Observe the accident prevention regulations, avoid damage to objects! 6

9 Recessing the slate Carefully cut a recess in the area where the roof hooks protrudes using an angle grinder. The recess regards to the installation variant of the base profile (V1 / V2) and has to align to the base profile and the used cover or lead flashing. For slate recovering proceed according to IV 3. V1 Observing the gap V2 Observe the accident prevention regulations, avoid damage to objects! Adjust the height of the roof hooks using the thread in the base profile. After fastening, the gap between the hook and the tile beneath must be 6 mm. 6 mm gap Not observing this gap can lead to the tile being damaged under loading. Fastening the roof hook Fasten the roof hooks to the rafter using wood screws (IV 4). The length of the screws depends on the roof construction and is determined by the design software. If the roof hook is installed on counter battens on the rafters or on over-rafter insulation, the base profile of the roof hook must be lined on both sides of the counter batten to at least the width of the rafter. The wood screws used in the system are approved by construction authorities. The use of own or nonequivalent wood screws renders the structural analysis invalid. 5.2 Installing the rails Installing the rail Place the C-rail on the lower locking bolt, align the rail and tighten using the upper locking bolt. The roof hook can also be connected to the joint area of the rail connector. If installing in a cross rail configuration, the upper rail is fastened using cross rail connectors (IV 5). Tightening torque for locking bolts: 50 Nm. 7

10 Connecting the rails Push the ends of the rails tightly together, place the rail connectors centrally and screw together using the screws contained in the set. The connector and the number of screws depend on the rail (IV 6). Maximum uninterrupted rail length 13 m, after this expansion joints or installation of floating bearings (IV 7). Tightening torque for locking bolts: 50 Nm. 5.3 Installing the module Observe the accident prevention regulations when sawing. Securing the module Prior to installing the module, the anti-slide protectors must be mounted on the holes in the frame above the upper or lower rail side (IV 8a/b). Clamping the module Following this, fasten the modules to the rails using end and centre clamps. Installing the end and centre clamps Insert the end or centre clamps into the rail cavity from above at the clamping position. Next, turn the rail nut in the rail and push the module clamps onto the module frame. 8

11 Space requirement for end and centre clamps The end clamp can also be installed flush with the rail end. Push the modules fully to the rail nuts of the centre clamps. End clamp: Centre clamp: 13 mm to 12 mm clearance rail end to module Tightening torque for centre clamps: 12 Nm, tightening torque for end clamps: 8 Nm. 5.4 Installation variants Explanation of the installation variants depending on the roof construction or design variants (e.g. horizontal module installation or cross rail configuration). IV 1 Roof hook set variants Roof hook set flex / double roof hook set flex: - For roof tiles / concrete roof tiles and beavertail roofing - Base profile height 30 or 40 mm - Hooks M10 Roof hook set PT: - For plain tile roofing - Base profile height 18 or 25 mm - Hooks M10 IV 2 Positioning the roof hook for Plain Tile roofing Hook central lower tile roughly above the Install the roof hook above the rafter and the upper batten. The hook should be positioned roughly centrally above the tile beneath, observing the protrusion on the side (IV 4). An additional screw (5.0 x 20mm) has to be screwed in above the hook into the batten. IV 3 Covering the roof hook for plain tile / slates roofing Install the plain tiles around the roof hook. 2. Install the recessed plain tile. 3. Cover the roof hook with a plain tile. 1. 9

12 Install the recessed slates around the roof hook. 2. Install cover and seal foam or lead flashing 3.s Install the recessed slate above the cover or the lead flashing. IV 4 Installing the roof hooks Close to hook Distance to edge Distance to edge The permitted protrusion of the roof hook beyond the rafter can be taken from the project structural analysis. The wood screws must be screwed in without pre-drilling observing the distances to the edge of the rafter. The wood screw along the hook axis must be screwed in as close to the hook as possible. An additional wood screw (5.0 x 20mm) is needed when using PT roof hook and screwed in above the hook into the batten (IV2). If using the double roof hook set, the same instructions apply and should be applied similarly. Distances to edge: Screw d = 6 mm D = 18 mm Protrusion The roof hook may only be installed on over-rafter insulation using wood screws d = 8 mm. IV 5 Installing the cross rail connectors Cross rail installation: Fasten the upper rails to the lower rail using cross rail connectors. Tightening torque for cross rail connectors: 40 Nm. IV 6 Installing the rail connectors 2 screws 4 screws Rail connectors: C-rail 47 (left): Connect the adjacent rail ends with a screw and locking bolt on each end. C-rail 71 and C-rail 95 (right): Connect the adjacent rail ends with two screws, washers and locking bolts on each end. Tightening torque for locking bolt: 50 Nm. 10

13 IV 7 Installing floating bearings on C-rails Fixed side Gap depending on C-rail Position the rail ends on the gap, put the rail connector in place and connect to the rail using the fastening screws on the fixed and moving sides. The screws on the fixed side must be tightened firmly. The screws on the moving side are painted red and must be loosened again after tightening (approx. ½ turn). Max. rail length with floating bearing 40 m, plan for proper expansion joint after this. Moving side Tightening torque for locking bolt on fixed side: 50 Nm. Distance between adjacent rail ends C-rail 47: 20 mm C-rails 71 and 95: mm IV 8a Installing anti-slide protector on module frame Thin sheet screw Push the nut over the screw and screw the thin sheet screw into the module frame without predrilling. Nut M6 Rear side Module frame Do not overtighten the thin sheet screw. IV 8b Installation of anti-slide protector with horizontal module 5 mm gap Screw the anti-slide protector to the end of the rail with a gap of approx. 5 mm using a fastening screw, a washer and a locking bolt. Tightening torque for locking bolt: 50 Nm. 11

14 6 Warranty / product liability and disclaimer In addition to the aforementioned regulations and safety instructions, the installation company must observe the valid regulations and standard engineering practice. The installation company is responsible for dimensioning the novotegra installation system. The installation company is responsible for connecting the interfaces between the installation system and the building. This also includes the seal tightness of the building envelope. On flat roofs, the installation company is responsible for the on-site assessment of the roof seal with regard to the sealing membrane material, durability, ageing, compatibility with other materials, general state of the roof seal and the need for a separation membrane between the roof seal and the installation system. The installation company must take the required and necessary measures and/or precautions for protecting the roof seal for the installation of the PV system substructure, if necessary with the involvement of a specialist. BayWa r.e. Solarsysteme GmbH shall bear no liability for incorrect or insufficient measures and precautions for protecting the roof seal. The installation company is responsible for the on-site testing of the coefficient of friction used in the calculation for verification of the anti-slide protection for PV systems on flat roofs. Coefficients of friction calculated on site can be taken into account and must be provided to BayWa r.e. Solarsysteme GmbH for the calculation. BayWa r.e. Solarsysteme GmbH shall assume no guarantee for the correctness of the assumed values and shall bear no liability in the event of damages caused as a result of the use of incorrect values. The instructions of the module, cable and inverter manufacturers must be observed. In the event of instructions that contradict those in this installation manual, be sure to contact your BayWa r.e. Solarsysteme GmbH sales team prior to installation or else the relevant manufacturer for components not supplied by BayWa r.e. Solarsysteme GmbH. Local conditions are not always sufficiently well known by our sales representatives when preparing quotations for novotegra. This may result in deviations from the quoted parts quantities during installation. These deviations mostly relate to the quantity of fastening material to the building envelope (such as roof hooks). In this case, the additionally required components must be installed in accordance with the dimensioning. BayWa r.e. Solarsysteme GmbH shall bear no liability for incorrectly or incompletely filled-in data survey sheets. Completely filled-in and error-free data survey sheets are essential for correct dimensioning. The information in the installation manual, the warranty conditions and the disclaimer information must be observed. 12

15 NOTES: 13

16 BayWa r.e. Solarsysteme GmbH Eisenbahnstrasse 150 D Tübingen Phone Fax solarsysteme.baywa-re.com Sales office Tübingen Sales office Munich Sales office Nuremberg Welzenwiler Strasse 5 Beethovenplatz 4 Wiesentalstrasse D Tübingen D Munich D Nuremberg Phone Phone Phone Fax Fax Fax tue.solarsysteme@baywa-re.com mue.solarsysteme@baywa-re.com nue.solarsysteme@baywa-re.com Sales office Duisburg Sales office Braunschweig BayWa r.e. solar systemer ApS Philosophenweg 21 Packhofpassage 3 Kullinggade 31E D Duisburg D Braunschweig DK-5700 Svendborg Phone Phone Phone Fax Fax Fax dui.solarsysteme@baywa-re.com bsg.solarsysteme@baywa-re.com solarsystemer@baywa-re.com Subject to errors and amendments. Date: November 2014/ASC, version 3.0 Copyright BayWa r.e. Solarsysteme GmbH 14

Installation instructions. Novotegra for Corrugated Fibre Cement / Sandwich Roofs

Installation instructions. Novotegra for Corrugated Fibre Cement / Sandwich Roofs Installation instructions Novotegra for Corrugated Fibre Cement / Sandwich Roofs I CONTENTS 1 General information... 0 2 Novotegra: mounting system planning... 1 2.1 Solar-Planit software... 1 2.1.1 General

More information

orientation Conergy SunTop Instructions for professional installation

orientation Conergy SunTop Instructions for professional installation On-roof Framed modules Portrait orientation Landscape Three-tab Shingle Plain tile Slate Double Roman tile Metal roof Material warranty orientation Conergy SunTop Instructions for professional installation

More information

Alpha + On-Roof System Installation manual

Alpha + On-Roof System Installation manual 810-0116 Alpha + On-Roof System Installation manual Content Alpha + A stroke of genius with a plus 1 Introduction 2 1.1 Short Description 2 1.2 About These Instructions 2 1.3 Warnings 3 1.4 Safety 3 2

More information

VarioSole SE. Installation instructions

VarioSole SE. Installation instructions VarioSole SE Installation instructions INTRODUTION Product Information VarioSole is a universal, easy to install system for the mounting of framed PV modules on pitched roofs with a roof pitch between

More information

INSTALLATION INSTRUCTIONS TRI-ROOF. energy for a better world

INSTALLATION INSTRUCTIONS TRI-ROOF. energy for a better world energy for a better world INSTALLATION INSTRUCTIONS TRI-ROOF The flexible roof integration system Compatible for framed module types* Simple exchange of modules Replaces existing roofing Special profiles

More information

Mounting systems for solar technology

Mounting systems for solar technology Mounting systems for solar technology ASSEMBLY INSTRUCTIONS Crosshook 3S CrossHook 4S GB Table of contents TABLE OF CONTENTS THE COMPANY SAFETY REGULATIONS MATERIALS REQUIRED TOOLS REQUIRED ASSEMBLY 2

More information

MANUAL MOUNTING SYSTEM FOR CORRUGATED ROOF

MANUAL MOUNTING SYSTEM FOR CORRUGATED ROOF MANUAL MOUNTING SYSTEM FOR CORRUGATED ROOF EN mounting system for corrugated roof for solar panels in portait setup (cross-system) ESDEC BV 2015 TABLE OF CONTENT 1. Introduction 1 2. General installation

More information

MOUNTING INSTRUCTIONS CONCRETE PURLIN BRACKET

MOUNTING INSTRUCTIONS CONCRETE PURLIN BRACKET CONCRETE PURLIN BRACKET VERSION MARCH 2015 GENERAL INSTRUCTIONS Safety: Systems may only be installed and operated by properly trained and technically suitable people (i.e. MCS accredited installers).

More information

MANUAL MOUNTING SYSTEM FOR BITUMEN / EPDM

MANUAL MOUNTING SYSTEM FOR BITUMEN / EPDM MANUAL MOUNTING SYSTEM FOR BITUMEN / EPDM EN mounting system for insulated pitched roof Bitumen / EPDM for solar panels landscape setup ESDEC BV 2015 TABLE OF CONTENT 1. Introduction 1 2. General installation

More information

Mounting systems for solar technology

Mounting systems for solar technology Mounting systems for solar technology ASSEMBLY INSTRUCTIONS Roof Fastener System CrossHook 2G GB Table of contents TABLE OF CONTENTS THE COMPANY SAFETY REGULATIONS MATERIALS REQUIRED TOOLS REQUIRED ASSEMBLY

More information

CSS Central Mount System

CSS Central Mount System CSS-20 Installation Manual CSS-20 Safety Notifications Below are the installation instructions for the CSS-20-2 Long Span Beam Mounting System. Please read these safety notifications prior to beginning

More information

MTS-SP100. RENOGY Pole Mount System E Philadelphia St, Ontario, CA Version: 1.2

MTS-SP100. RENOGY Pole Mount System E Philadelphia St, Ontario, CA Version: 1.2 MTS-SP100 RENOGY Pole Mount System 2775 E Philadelphia St, Ontario, CA 91761 1-800-330-8678 1 Version: 1.2 Important Safety Instructions Please save these instructions. This manual contains important safety,

More information

Installation Instructions

Installation Instructions Installation Instructions SOLC 220 SOLC 220 PAG SOLC 220 PAE SOLC 220 BAG SOLC 220 BAE Flat plate collector Basic kit Frankfurt tile Extension kit Frankfurt tile Basic kit plain tile Extension kit plain

More information

Code-Compliant Planning and Installation Complying with AS/NZS1170.2:2011 ADMT

Code-Compliant Planning and Installation Complying with AS/NZS1170.2:2011 ADMT PV-ezRack SolarRoof Code-Compliant Planning and Installation Complying with AS/NZS1170.2:2011 ADMT 2-2012 CONTENT 1. Introduction 2 2. Planning. 3 3. Component List 9 4. Array planning.. 10 5. Step by

More information

INSTALLATION INSTRUCTIONS ENGLISH

INSTALLATION INSTRUCTIONS ENGLISH INSTALLATION INSTRUCTIONS ENGLISH Safety instructions 04 General notes 07 Material & tool requirements 08 System overview 10 installation of HANGER BOLTS 12 Maintenance 23 04 INTENDED USE Creotecc mounting

More information

INSTALLATION GUIDE SM SOLAR MOUNT PUB15JAN01

INSTALLATION GUIDE SM SOLAR MOUNT PUB15JAN01 MOUNT INSTALLATION GUIDE PUB5JAN0 SM SOLAR Wrenches and Torque Wrench Size Recommended Torque (ft-lbs) /4 Hardware 7/6 *0 3/8 Hardware 9/6 *30 # Hardware 5/6 0 Torques are not designed for use with wood

More information

On-Roof Mounting Sets for Flat-Plate Collectors

On-Roof Mounting Sets for Flat-Plate Collectors Engineering Submittal Sheet Installation sets for collectors Fig. 1 Installation set for 2 collectors 1 basic installation set, 1 extension installation set Basic installation set for each collector array

More information

SolarMount (E)volution

SolarMount (E)volution SolarMount (E)volution SOLARMOUNT (E)VOLUTION: THE BEST JUST GOT BETTER. Engineering, Excellence, and Ease. Performance Engineered for versatility and reduced installation time, SolarMount (E)volution

More information

Greenhouse Assembly Instructions

Greenhouse Assembly Instructions Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free 7 days a week on 0800

More information

INSTALLATION GUIDE DECKING.

INSTALLATION GUIDE DECKING. INSTALLATION GUIDE DECKING www.ttp-online.de/resysta CONTENT LATEST TEST RESULT Classification C, DIN 51097: Features, made by, best skid-resistance properties and is eminently suitable for wet barefoot

More information

INSTALLATION GUIDE SM SOLAR MOUNT PUB15JUN15

INSTALLATION GUIDE SM SOLAR MOUNT PUB15JUN15 MOUNT INSTALLATION GUIDE PUB5JUN5 Wrenches and Torque SM SOLAR Wrench Size Recommended Torque (ft-lbs) /4 Hardware 7/6 *0 3/8 Hardware 9/6 *30 # Hardware 5/6 0 Torques are not designed for use with wood

More information

Fig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7

Fig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7 FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track

More information

Gardman Lean-to Greenhouse Assembly Instructions

Gardman Lean-to Greenhouse Assembly Instructions Page 1 Gardman Lean-to Greenhouse Assembly Instructions Our Help Line provides support and advice to customers of Summer Garden Buildings after ordering. For advice before you buy you can phone us free

More information

Assembly instructions Pantograph shutters

Assembly instructions Pantograph shutters Assembly instructions Pantograph shutters Read these instructions, observe the contents and the warning notes prior to assembly. The information is very important for installation and correct use of the

More information

XIAMEN FENGWEI ENERGY TECHNOLOGY CO., LTD. GRACE SOLAR ROOF MOUNTING SYSTEM INSTALLATION Manual

XIAMEN FENGWEI ENERGY TECHNOLOGY CO., LTD. GRACE SOLAR ROOF MOUNTING SYSTEM INSTALLATION Manual XIAMEN FENGWEI ENERGY TECHNOLOGY CO., LTD. GRACE SOLAR ROOF MOUNTING SYSTEM INSTALLATION Manual Contents Chapter Title Page 1 General information 3 2 Safety and Installer Responsibilities 4 3 Technical

More information

GSE INTEGRATION INSTALLATION MANUAL For photo-voltaic systems partially covering the roof

GSE INTEGRATION INSTALLATION MANUAL For photo-voltaic systems partially covering the roof GSE INTEGRATION INSTALLATION MANUAL For photo-voltaic systems partially covering the roof V 7.5 WWW.GSEINTEGRATION.COM Contents STEP BY STEP Presentation of system p.4 Contents of kit p.5 GSE Integration

More information

Mounting systems for solar technology

Mounting systems for solar technology Mounting systems for solar technology ASSEMBLY INSTRUCTIONS Roof Fastener Pan Tile GB Table of contents TABLE OF CONTENTS THE COMPANY SAFETY REGULATIONS MATERIALS REQUIRED TOOLS REQUIRED ASSEMBLY 2 3 4

More information

Installation Guide Simplicity Alfresco. V1.9 Lu070318

Installation Guide Simplicity Alfresco. V1.9 Lu070318 0333 305 5272 www.canoports.co.uk Installation Guide Simplicity Alfresco V1.9 Lu070318 Tools Required Below is a list of tools that you will require to install your the Simplicity Alfresco System. Cordless

More information

Step-by-Step Installation Instructions for

Step-by-Step Installation Instructions for Step-by-Step Installation Instructions for Version 5-06/11 Before Starting: Please read and understand these instructions. Not following these instructions will invalidate your warranty (although this

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

On-roof system Alpha + Product catalogue

On-roof system Alpha + Product catalogue On-roof system Alpha + Product catalogue Contents ALPHA +... 3 1. ALPHA + BASE RAILS... 4 2. ALPHA + SPLICES... 5 3. ALPHA + TELESCOPING END PIECES... 6 4. ALPHA + INTER-MODULE CLAMPS AND MODULE END CLAMPS...

More information

SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL

SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL Strong Razor Series Articulating Mount for Large and Extra Large Displays INSTRUCTION MANUAL Installation Manual Warnings: Installation of this product should be done

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

INSTALLATION INSTRUCTIONS TRI-VENT. energy for a better world

INSTALLATION INSTRUCTIONS TRI-VENT. energy for a better world energy for a better world INSTALLATION INSTRUCTIONS TRI-VENT The photovoltaic mounting system for trapezoidal sheet roofs Quick and easy installation Riveting instead of glueing Securing without screws

More information

FS Uno mounting instructions. 2 Pile driving (Ramming) 5. 6 Components list Torque specifications 15

FS Uno mounting instructions. 2 Pile driving (Ramming) 5. 6 Components list Torque specifications 15 FS Uno System Mounting instructions CONTTS Page 1 General - Safety, planning and tools 2 2 Pile driving (Ramming) 5 3 Rack overview - Components and fasteners 6 4 Mounting of the individual assembly groups

More information

Roof fastener. Perfectly thought out for every roof

Roof fastener. Perfectly thought out for every roof Roof fastener Perfectly thought out for every roof 1 Welcome to the world of clever solutions Solutions for every roof In our production areas we produce all needed components for the sub construction

More information

ALUMINIUM SOLAR MOUNTING SYSTEM. Components catalogue FOR ALL TYPES OF ROOFS AND SITES

ALUMINIUM SOLAR MOUNTING SYSTEM. Components catalogue FOR ALL TYPES OF ROOFS AND SITES Components catalogue MOUNTING RAILS CARRIERS FOR RAILS FASTENERS BOLTS AND NUTS CLIPS FLAT ROOFS STRUCTURES FREE FIELD SYSTEMS COMPLEX ROOFS SYSTEMS ALUMINIUM SOLAR MOUNTING SYSTEM FOR ALL TYPES OF ROOFS

More information

ASSEMBLY INSTRUCTIONS. Construction type approved Reg. no S819 F ENERGY AND SANITARY SYSTEMS

ASSEMBLY INSTRUCTIONS. Construction type approved Reg. no S819 F ENERGY AND SANITARY SYSTEMS Heliostar 252 S4 and 218 S4 FREE-STANDING INSTALLATION vertical ASSEMBLY INSTRUCTIONS Construction type approved Reg. no. 011-7S819 F ENERGY AND SANITARY SYSTEMS Safety instructions Safety instructions

More information

HERCULES EXTENDED TOWER

HERCULES EXTENDED TOWER AmeriGlide Accessibility Solutions HERCULES EXTENDED TOWER ATION GUIDE Please read this installation guide carefully to ensure correct installation of the HERCULES EXTENDED TOWER Vertical Platform Lift.

More information

Installation Manual. This installation is for the Odyssey H1800 Series Ventilation System.

Installation Manual. This installation is for the Odyssey H1800 Series Ventilation System. Installation Manual This installation is for the Odyssey H1800 Series Ventilation System. This installation is limited to roofs with pitches between 3 and 35. This instruction assumes that there is a power

More information

Mounting system for sloped composite shingle roofs with solar panels in portrait orientation

Mounting system for sloped composite shingle roofs with solar panels in portrait orientation MANUAL USA MOUNTING SYSTEM FOR SLOPED COMPOSITE SHINGLE ROOFS Mounting system for sloped composite shingle roofs with solar panels in portrait orientation ESDEC BV 2016 CONTENT page 1. Introduction 1 2.

More information

Installing flat panels on the MPL15 wall mount

Installing flat panels on the MPL15 wall mount Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape

More information

AWNING SYSTEM INSTALLATION INSTRUCTIONS ALL VERTICAL WALLS

AWNING SYSTEM INSTALLATION INSTRUCTIONS ALL VERTICAL WALLS INSTALLATION MANUAL AWNING SYSTEM INSTALLATION INSTRUCTIONS ALL VERTICAL WALLS TABLE OF CONTENTS Table of Contents... 3 Components... 4 System Components... 6 Attachment Components... 7 Module Compatibility...

More information

Installation manual for sloped roof assembly system. Jurchen Technology GmbH Prinz-Ludwig-Straße Helmstadt

Installation manual for sloped roof assembly system. Jurchen Technology GmbH Prinz-Ludwig-Straße Helmstadt Installation manual for sloped Jurchen Technology GmbH Prinz-Ludwig-Straße 5 9764 Helmstadt Index. Security note.... Hazard note.... Planning and installation notes.... Installation notes... 4. Outline

More information

Installation Manual FLUSH MOUNT - Shingle, Slate,etc. Questions? Call Us! +1 (800)

Installation Manual FLUSH MOUNT - Shingle, Slate,etc. Questions? Call Us! +1 (800) www.trasnowandsun.com S Installation Manual FLUSH MOUNT - Shingle, Slate,etc. At TRA Snow and Sun we engineer and layout each project upon request free of charge. Just give us the project details and we

More information

Repair manual. Fifth-wheel coupling JSK 38/50

Repair manual. Fifth-wheel coupling JSK 38/50 Repair manual Fifth-wheel coupling JSK 38/5 ZDE 199 3 12 E 6/212 1 Foreword Table of contents Page Fifth wheel couplings are connecting parts that must comply with very high safety requirements and must

More information

MTS-ZB. RENOGY Photovoltaic Module Z-Bracket Mounting System E Philadelphia St, Ontario, CA Version: 1.

MTS-ZB. RENOGY Photovoltaic Module Z-Bracket Mounting System E Philadelphia St, Ontario, CA Version: 1. MTS-ZB RENOGY Photovoltaic Module Z-Bracket Mounting System 2775 E Philadelphia St, Ontario, CA 91761 1-800-330-8678 1 Version: 1.0 Important Safety Instructions Please save these instructions. This manual

More information

Installation Guide Contemporary Alfresco V1.3 LU

Installation Guide Contemporary Alfresco V1.3 LU Installation Guide Contemporary Alfresco V1.3 LU 010818 Tools Required Below is a list of tools that you will require to install you're the Contemporary Alfresco System. Cordless Drill Mastic Gun Spirit

More information

PEDESTAL INSTALLATION. Guidelines for installing adjustable height pedestals

PEDESTAL INSTALLATION. Guidelines for installing adjustable height pedestals BASIC REQUIREMENTS Irrespective of the type of pavers or tiles that will be installed over pedestals, the following basic requirement must be met. Decks must be designed not to exceed the load capacity

More information

INS A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Unpacking the KSCR Splicing the KSCR (If Required)...

INS A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Unpacking the KSCR Splicing the KSCR (If Required)... INS-88.500-0A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE 1. Unpacking the KSCR... 2 2. Splicing the KSCR (If Required)... 4 3. Assemble Curb and Rail Corners... 5 4. Install Cross Bracing (If Required)...

More information

B B B

B B B Winchester SXP Gauge Tactlite Six Position Adjustable Shotgun Stock with Scorpion Recoil System B..0.00 B..0.00 B..0.00 Removable/Adjustable Tactical Cheekrests X Scorpion Recoil Pad Dual Sided QD Attachment

More information

TITGEMEYER Tf1663GB(0514)1. GETO Megaport II flush rear doors Assembly Instructions

TITGEMEYER Tf1663GB(0514)1. GETO Megaport II flush rear doors Assembly Instructions TITGEMEYER GETO Megaport II flush rear doors All rights reserved. The technical data quoted in this catalogue, performance descrip - tions, recommendations and instructions e.g. for the installation of

More information

SAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20

SAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42-55 Page 20 SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management

More information

MTS-ACB. RENOGY Photovoltaic Module Adjustable Curved Bracket E Philadelphia St, Ontario, CA Version: 1.

MTS-ACB. RENOGY Photovoltaic Module Adjustable Curved Bracket E Philadelphia St, Ontario, CA Version: 1. MTS-ACB RENOGY Photovoltaic Module Adjustable Curved Bracket 2775 E Philadelphia St, Ontario, CA 91761 1-800-330-8678 1 Version: 1.0 Important Safety Instructions Please save these instructions. This manual

More information

Outdoor Water Solutions, Inc. Small Backyard Windmill. Installation Manual

Outdoor Water Solutions, Inc. Small Backyard Windmill. Installation Manual Outdoor Water Solutions, Inc. Small Backyard Windmill Installation Manual Customer Service: 1-866-471-1614 Website: www.outdoorwatersolutions.com Springdale, Arkansas 72764 Phone: 1-866-471-1614 Fax: 1-479-750-9178

More information

SunPower Installation Manual

SunPower Installation Manual SunPower SF System Planning and Assembly SunPower SUNPOWER CORPORATION WWW.SUNPOWERCORP.COM Pub #101001-SP2 October 2010 - Rev. 8 2010 by SunPower, Corp All rights reserved. Part I. Scope, components,

More information

Sliding Door Kit

Sliding Door Kit YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT. Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable

More information

ROOF MOUNT. *Class A* Fire Rated INSTALLATION MANUAL

ROOF MOUNT. *Class A* Fire Rated INSTALLATION MANUAL ROOF MOUNT 4008083 *Class A* Fire Rated INSTALLATION MANUAL Contents DISCLAIMER 1 RATINGS 1 CHECKLIST 2 PRIMARY COMPONENTS 3 1. ATTACH BASES 3 2. PLACE RAILS 3 3. SECURE LUG 4 4. CLAMP MODULES 4 EXPANSION

More information

4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.

4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside. Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps

More information

Fifth-wheel coupling JSK 38/50

Fifth-wheel coupling JSK 38/50 Repair manual Fifth-wheel coupling JSK 38/5 ZDE 199 3 12 E 6/25 1 LT SK38C-3 English RevA Foreword Table of contents Page Fifth wheel couplings are connecting parts that must comply with very high safety

More information

TYPHOON ASSEMBLY AND INSTALLATION INSTRUCTIONS

TYPHOON ASSEMBLY AND INSTALLATION INSTRUCTIONS TYPHOON ASSEMBLY AND INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 Phone: (503) 266-2231 Fax: (503) 266-4334

More information

SM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL

SM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation

More information

TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS

TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 Phone: (503) 266-2231 Fax: (503) 266-4334

More information

Solar Competence. ALUMERO Metal Components Assembly Instruction for Solar Mounting System DT-1. Systematic Solutions

Solar Competence. ALUMERO Metal Components Assembly Instruction for Solar Mounting System DT-1. Systematic Solutions Solar Competence ALUMERO Metal Components Assembly Instruction for Solar Mounting System DT-1 ALUMERO GROUP Your big advantage! + In-house consulting and design office 4 ) Lap-joint sheet covered roof

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

PATIO INSTALLATION MANUAL

PATIO INSTALLATION MANUAL PATIO INSTALLATION MANUAL A few minutes spent reviewing the following instructions will help insure quick and proper assembly. The Patio Sauna Kit will arrive on a stretchwrapped pallet including pre-built

More information

SOLAR ROOF MOUNTING SYSTEM INSTALLATION MANUAL Model Name TT-ADJUSTABLE TILT LEGS

SOLAR ROOF MOUNTING SYSTEM INSTALLATION MANUAL Model Name TT-ADJUSTABLE TILT LEGS SOLAR ROOF MOUNTING SYSTEM INSTALLATION MANUAL Model Name TT-ADJUSTABLE TILT LEGS JIANGYIN TITANERGY CO.,LTD Contents Chapter Title Page 1 General Information 3 2 Safety and Installer Responsibilities

More information

Patented Rail-Free Mounting System for Composition/Asphalt Shingle Roofs

Patented Rail-Free Mounting System for Composition/Asphalt Shingle Roofs Quick Start Guide Patented Rail-Free Mounting System for Composition/Asphalt Shingle Roofs R ESPECT T HE R OOF Quick Rack Components & Tools Components are pre-assembled and ready for installation right

More information

Owner s Manual & Safety Instructions

Owner s Manual & Safety Instructions Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s

More information

XL-GC03 Sliding Door Lock Installation Manual PAT XL-GC06 Sliding Door Hanger Installation Manual XL-GC08 Sliding Door Lock Guide Installation Manual

XL-GC03 Sliding Door Lock Installation Manual PAT XL-GC06 Sliding Door Hanger Installation Manual XL-GC08 Sliding Door Lock Guide Installation Manual XL-GC0 Sliding Door Lock Installation Manual PAT XL-GC0 Sliding Door Hanger Installation Manual XL-GC0 Sliding Door Lock Guide Installation Manual Read all instructions carefully before installation. Before

More information

GARAGE DOOR WITH TORSION SPRING

GARAGE DOOR WITH TORSION SPRING GARAGE DOOR WITH TORSION SPRING DIMENSIONS 9 WIDTH X 7 HEIGHT (2.74m x 2.13m) IMPORTANT SAFETY INSTRUCTIONS WARNING: Read all instructions and warnings before use. Failure to follow all instructions may

More information

STOP. V00029AC Rev. 04 READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID TOOL LIST. NET-ACCESS S-Type Network Cabinets

STOP. V00029AC Rev. 04 READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID TOOL LIST. NET-ACCESS S-Type Network Cabinets Rev. 04 STOP READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID NET-ACCESS S-Type Network Cabinets -Phillips screwdriver -Flatblade screwdriver -22mm socket wrench -15mm socket wrench

More information

10 Octagon Cedar Gazebo Assembly Instructions

10 Octagon Cedar Gazebo Assembly Instructions 10 Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/22/09 10 Cedar Gazebo Assembly Instructions

More information

TURBOTWISTER TM ASSEMBLY AND INSTALLATION INSTRUCTIONS

TURBOTWISTER TM ASSEMBLY AND INSTALLATION INSTRUCTIONS TURBOTWISTER TM ASSEMBLY AND INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 Phone: (503) 266-2231 Fax: (503)

More information

1. TOOLS + MATERIALS REQUIRED

1. TOOLS + MATERIALS REQUIRED R INSTALLATION INSTRUCTIONS PRODUCT: BALDUR + ODEN CONFIGURATION: BI-PARTING DOOR MOUNT: TOP MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com. TOOLS + MATERIALS REQUIRED

More information

Installation Manual for The Asphalt/Bitumen Shingle Roof Hook System

Installation Manual for The Asphalt/Bitumen Shingle Roof Hook System Installation Manual for The Asphalt/Bitumen Shingle Roof Hook System (F-IMG-1534-SolNV) Installation of Asphalt/Bitumen Shingle Roof Hook System Installing Rail / Purlin System Installing Cross Rail System

More information

Rayport G Eco Dealer Kit

Rayport G Eco Dealer Kit Rayport G Eco Dealer Kit Installation Guide www.aetenergy.com Supporting a Cleaner, Greener Tomorrow 1. Table of Contents 1. Table of Contents P2 2. Installer Notes P3 3. Parts List P4-7 4. Tool List P8

More information

Installation Manual XRL Solar Rail System

Installation Manual XRL Solar Rail System Installation Manual XRL Solar Rail System Solar Mounting Solutions June 2009 www.ironridge.com 2009 IronRidge, Inc. All Rights Reserved Version 1.0 2 XRL Solar Rail System Installation Guide Introduction

More information

TITGEMEYER Tf1673GB(0517)1. GETO City Body Kit with a self-supporting base and without a base Assembly Instructions

TITGEMEYER Tf1673GB(0517)1. GETO City Body Kit with a self-supporting base and without a base Assembly Instructions TITGEMEYER Tf1673GB(0517)1 with a self-supporting base and without a base All rights reserved. The technical data quoted in this catalogue, performance descrip - tions, recommendations and instructions

More information

TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS

TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 Phone: (503) 266-2231 Fax: (503) 266-4334

More information

IMS Nederland INSTALLATION GUIDE. SB-LED Indoor. winner

IMS Nederland INSTALLATION GUIDE. SB-LED Indoor. winner IMS Nederland INSTALLATION GUIDE winner V1.0-2015 CONTENTS 1 Introduction 4 1.1 About this guide 4 1.2 Product description 4 1.3 Symbols used in this guide 5 2 Precautions and safety instructions 6 3 Technical

More information

Pocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.

Pocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents. Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =

More information

This installation guide has been created to assist in constructing a Liniar conservatory roof from a kit format.

This installation guide has been created to assist in constructing a Liniar conservatory roof from a kit format. 1.00 - Introduction This installation guide has been created to assist in constructing a Liniar conservatory roof from a kit format. Please note, each roof has been individually designed to meet specific

More information

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02

GROWING BETTER THROUGH DESIGN. 6ft Lean-To LEAN-TO. Assembly Instructions 04/02 GROWING BETTER THROUGH DESIGN 6ft Lean-To LEAN-TO Assembly Instructions 04/02 6ft Lean-To Greenhouse Base Plan Introduction/Tools/Contents / / Contents This is a copy of our Lean-To greenhouse base plan.

More information

ROOF MOUNT. *Class A* Fire Rated INSTALLATION MANUAL

ROOF MOUNT. *Class A* Fire Rated INSTALLATION MANUAL ROOF MOUNT 4008083 *Class A* Fire Rated INSTALLATION MANUAL CONTENTS DISCLAIMER 1 RATINGS 1 CHECKLIST 2 PRIMARY COMPONENTS 3 0. ATTACH BASES 3 1. PLACE RAILS 3 2. SECURE LUG 4 3. CLAMP MODULES 4 EXPANSION

More information

150 MM FREE STANDING WOOD FIRE FLUE KIT INSTALLATION INSTRUCTIONS

150 MM FREE STANDING WOOD FIRE FLUE KIT INSTALLATION INSTRUCTIONS www.jayline.co.nz www.fisherstoves.co.nz 150 MM FREE STANDING WOOD FIRE FLUE KIT INSTALLATION INSTRUCTIONS WARNING: This flue kit has been manufactured in accordance with as/nzs 2918:2001 and tested to

More information

Octagon Vinyl Gazebo Assembly Instructions

Octagon Vinyl Gazebo Assembly Instructions Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly

More information

Pole Mount Installation Manual

Pole Mount Installation Manual Pole Mount Installation Manual Thank You for Choosing AIMS Power! 1. AIMS Power is a leading supplier of solar products, specializing in PV mounting systems. We ensure our products are manufactured to

More information

SecuAnch Roof Anchor System

SecuAnch Roof Anchor System Height Safety Products Email: marketing@fallprotec.com SecuAnch Roof Anchor System 1 Presentation The SecuAnch lifeline is designed to be permanently installed on buildings and other structures where maintenance

More information

INSTALLATION MANUAL H A

INSTALLATION MANUAL H A INSTALLATION MANUAL CABINET RACK CR-43-6 (4-UNIT SIZE) Be sure to read this installation manual thoroughly before installing this Cabinet Rack. For the mounting procedures of the components and the relevant

More information

MPA-9000 Universal Ceiling Projector Mount Kit

MPA-9000 Universal Ceiling Projector Mount Kit I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low

More information

Magnum low voltage drawout circuit breaker IEC horizontal stab cassette shutter kit (double wide A cassettes)

Magnum low voltage drawout circuit breaker IEC horizontal stab cassette shutter kit (double wide A cassettes) kit (double wide 4000 6300A cassettes) i WARNING (1) ONLY QUALIFIED ELECTRICAL PERSONNEL SHOULD BE PERMITTED TO WORK ON THE EQUIPMENT. (2) ALWAYS DE-ENERGIZE PRIMARY AND SECONDARY CIRCUITS IF A CIRCUIT

More information

Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays

Installation and Assembly: Articulating Swivel Arm for 37 - 60 Flat Panel Displays Installation and Assembly: Articulating Swivel Arm for 37" - 60" Flat Panel Displays Models: PLA60, PLA60-S, PLAV60, PLAV60-S Max UL Load Capacity: 175 lb (79 kg) 2300 White Oak Circle Aurora, Il 60502

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS PART NO. 911000T 911000PS 915000T 915000PS PRODUCT DESCRIPTION: Sport Bar 2.0, Full size Textured Black Sport Bar 2.0, Full size Polished Stainless Steel Tubes Sport Bar 2.0, Mid size Textured Black PRODUCT

More information

Installation Instructions

Installation Instructions Installation Instructions Alpha SolarSmart On Roof Kits for the Installation of Alpha Solar Collectors onto Tile and Slate Type Roofs For Technical help or for Service call... ALPHA HELPLINE Tel: 0 77

More information

Installation Guidelines

Installation Guidelines Page 1 Tools You ll Need 4 ft. Carpenter s level Chalk line (to mark U channel locations) Cordless drill/nut driver Caulking gun Chop saw with a metal cutting blade on it (required to make accurate and

More information

Roof Only Lean-to Instruction Manual

Roof Only Lean-to Instruction Manual Roof Only Lean-to Instruction Manual for 10 x 20 2 x 8 /10 6 covers Our unique assembly process quickly transforms the individual pieces into a finished structure that will give you a lifetime of service.

More information

MODEL 83 Pail Handler

MODEL 83 Pail Handler MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE

More information

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER. SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information