INSTRUCTIONS UNIVERSAL TRAY STAND - SMALL AASFT24 AASLH24 AASLP24
|
|
- Loraine Benson
- 6 years ago
- Views:
Transcription
1 UNIVERSAL TRAY STAND - SMALL AASFT24 AASLH24 AASLP24
2 Thank you for purchasing the Active Aqua Universal Tray Stand. This 2 x 4 stand supports Active Aqua 2' x 4' flood tables (and most any other brand of 2' x 4' flood tables) and allows you to move them easily when necessary. WHAT S IN THE BOX FIGURE 1 BOTTOM STAND PARTS LIST (AASFT24) A - Corner Leg (Standard Height) w/casters V1 (2) B - Corner Leg (Standard Height) w/casters V2 (2) C - Side Rail (2) D - End Rail (2) E - Center Support Rail Assembly (1) F - Corner Retainer V1 (2) G - Corner Retainer V2 (2) 2
3 ASSEMBLY INSTRUCTIONS (FOR BOTTOM STAND ONLY AASFT24): Remove all of the parts from the packaging and set the hardware aside. Group all of the stand parts together based on type for ease of locating and assembly, i.e. corner legs together, side rails together, end bars together, etc. All parts will be marked with a letter corresponding to the parts list on page Begin by inserting the Side Rails (Part C) into the Corner Legs V1 (Part A) and Corner Legs V2 (Part B), locking them into position with the spring buttons (see Image 1). Image 1 Image 2 NOTE: Be sure to install the Corner Legs V1 at two opposite corners from each other, and the Corner Legs V2 at the two remaining opposite corners. They must be installed this way or the assembly will be incorrect. NOTE: If you are adding a Light Hanger to your bottom stand, STOP HERE and continue the assembly using the section titled ASSEMBLY INSTRUCTIONS (INCLUDING LIGHT HANGER) (page 4). 2. Next, insert the End Rails (Part D) into the remaining openings in the Corner Legs V1 (Part A) and Corner Legs V2 (Part B), locking them into position with the spring buttons (see Image 2). 3. Connect your 2-Piece Center Support Rail (Part E), locking it into proper position with the spring button (see Image 3). 4. Now you can insert the Corner Retainers V1 and V2 (Parts F & G), placing them as shown in Figure 1 (be sure to place the Corner Retainers V1 at opposite corners to each other and the Corner Retainers V2 at opposite corners to each other as you did with the legs) (see Image 4). Image 3 Image 4 3
4 LIGHT HANGER PARTS LIST (AASLH24) A1 - Vertical Light Bar (2) B1 - Trellis Bar (2) C1 - Horizontal Light Bar (2) D1 - Butterfly thumb screw (4) E1 - Center Light Bar (1) F1 - Lynch Pin (4) ASSEMBLY INSTRUCTIONS (INCLUDING LIGHT HANGER AASLH24) Remove all of the parts from the packaging and set the hardware aside. Check to be sure that the hardware contains the Lynch Pins (quantity: 4) and Butterfly Thumb Screws (quantity: 4). Group all of the stand parts together based on type for ease of locating and assembly, i.e. corner legs together, side rails together, end bars together, etc. All parts will be marked with a letter corresponding to the parts list above. 4
5 1. Begin by inserting the Side Rails (Part C) into the Corner Legs V1 (Part A) and Corner Legs V2 (Part B), locking them into position with the spring buttons (see Image 1). 2. Install the End Rails (Part D) into the foundation squares of the Vertical Light Bars (Part A1) (see image 6). Secure each end rail and foundation square together with one of the butterfly thumb screws (Part D1). Image 6 Image 7 3. Attach the Horizontal Light Bars (Part C1) to the Vertical Light Bars (Part A1) (see Image 7). 4. Attach Trellis Bars (Part B1) to the Vertical Light Bars (Part A1) and lock them in place using Lynch Pins (Part F1) (see Image 8). 5. Use the second pair of Lynch Pins (Part F1) to adjust the height of the light hanger by inserting them into the appropriate holes in the Vertical Light Bars (Part A1) (see Image 9). Image 8 Image 9 6. To adjoin the two vertical bar sections, insert the Center Light Bar (Part E1) into the Horizontal Light Bars (Part C1) and secure it using both Butterfly Thumb Screws (Part D1) (see Image 10). 7. Complete the assembly by inserting the Corner Retainers V1 and V2 (Parts F & G), placing them as shown in Image 4 (be sure to place the Corner Retainers V1 at opposite corners to each other and the Corner Retainers V2 at opposite corners to each other as you did with the legs). Image 10 5
6 INSTALLATION OF THE LOW PROFILE LEG KIT NOTE: The below instructions assume that you have already used the standard sized legs and are switching to the low profile legs. If you want to assemble the stand with the low profile legs from the start, simply use the Low Profile Corner Legs V1 and Low Profile Corner Legs V2 in place of the standard length corner legs when assembling the bottom tray stand. Be sure to install the Low Profile Corner Legs V1 at two opposite corners from each other, and the Low Profile Corner Legs V2 at the two remaining opposite corners. They must be installed this way or the assembly will be incorrect. 1. To install the Low Profile Leg Kit, first decouple all four Corner Legs (Parts A & B) from the End Rails (Part D) and Side Rails (Part C) by depressing the spring buttons and pull them away from the Side Rails and End Rails. Image Replace the Corner Legs V1 (Part A) with the Low Profile Corner Legs V1 (Part A2) and replace the V2 Corner Legs (Part E) with the Low Profile Corner Legs V2 (Part B2). AASLP24 6
7 7
8 WARRANTY LIMITED WARRANTY Hydrofarm warrants the AASFT24, AASLH24, AASLP24 to be free from defects in materials and workmanship. The warranty term is for one year beginning on the date of purchase. Misuse, abuse, or failure to follow instructions is not covered under this warranty. Hydrofarm s warranty liability extends only to the replacement cost of the product. Hydrofarm will not be liable for any consequential, indirect, or incidental damages of any kind, including lost revenues, lost profits, or other losses in connection with the product. Some states do not allow limitation on how long an implied warranty lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to you. Hydrofarm will, at our discretion, repair or replace the AASFT24, AASLH24, AASLP24 covered under this warranty if it is returned to the original place of purchase. To request warranty service, please return the AASFT24, AASLH24, AASLP24, with original sales receipt and original packaging, to your place of purchase. The purchase date is based on your original sales receipt. GARANTIE LIMITÉE Hydrofarm garantit que le AASFT24, AASLH24, AASLP24 ne présente aucun défaut de pièces et maind œuvre. La période de garantie est d un an à partir de la date d achat. Une utilisation incorrecte, abusive, ou le non-respect des instructions n est pas couvert(e) par cette garantie. La responsabilité de la garantie Hydrofarm couvre uniquement le coût de remplacement du produit. Hydrofarm ne pourra être tenu responsable des dommages consécutifs, indirects ou fortuits de tout type, y compris les pertes de revenus, de profits ou autres en rapport avec le produit. Certains états n autorisent aucune limite concernant la durée de la garantie implicite ou l exclusion des dommages fortuits ou consécutifs ; les limites ou exclusions mentionnées ci-dessus peuvent donc ne pas être applicables à votre cas. Hydrofarm se réserve le droit de réparer ou remplacer le AASFT24, AASLH24, AASLP24 couvert par cette garantie si celui-ci est renvoyé au lieu d achat d origine. Pour solliciter le service de garantie, veuillez renvoyer le AASFT24, AASLH24, AASLP24 avec sa facture et son emballage d origine à votre lieu d achat. La date d achat est indiquée sur votre facture originale. GARANTÍA LIMITADA Hydrofarm garantiza que el AASFT24, AASLH24, AASLP24 no presentará defectos de fabricación. La garantía tendrá una duración de un año desde la fecha de compra. En caso de no respetarse estas instrucciones o de un uso inadecuado del producto, la garantía no cubrirá los posibles daños. La cobertura de la garantía ofrecida por Hydrofarm únicamente incluye los costes de sustitución del producto. Hydrofarm no será responsable de ningún daño indirecto, accidental o derivado de ningún tipo, incluyendo pérdidas de ingresos o beneficios, o cualquier otra pérdida relacionada con el producto. En algunos estados no se permiten limitaciones sobre la duración de una garantía implícita o la exclusión de los daños accidentales o derivados; en cuyo caso las limitaciones y exclusiones anteriores no serán de aplicación. Hydrofarm, a su discreción, podrá reparar o sustituir el AASFT24, AASLH24, AASLP24 cubierto por esta garantía siempre que se devuelva al lugar original de compra. Para reclamar la garantía, devuelva el AASFT24, AASLH24, AASLP24 con el ticket de compra y el embalaje original al lugar de compra. La fecha de compra será la indicada en el ticket original AASFT24, AASLH24, AASLP24 Instructions revised - November 15, :56 PM
INSTRUCTIONS VERTICAL GROW SHELF SYSTEM VGS300 & VGS600
INSTRUCTIONS VERTICAL GROW SHELF SYSTEM VGS300 & VGS600 INSTRUCTIONS Thank you for purchasing the Hydrofarm Vertical Grow Shelf System. This product is an easy-toassemble shelving system ideal for propagation
More informationNo: /16 rev. 1 Installation Instructions Instructions d Installation Instrucciones de Instalación UNIT DESCRIPTION
Wattstopper Low Voltage Outdoor Motion Sensor No: 24260 09/16 rev. 1 Installation Instructions Instructions d Installation Instrucciones de Instalación Catalog Number Numéro de Catalogue Número de Catálogo:
More information120 headboard/bed. headboard components. headboard & side rails hardware. Assembly Instructions for 120 Series
120 headboard/bed Assembly Instructions for 120 Series headboard components (1) Headboard (2) wings (2) metal legs headboard & side rails hardware (8) 3 x 5/16 bolts (10) 1 x 5/16 bolts (4) 1 x ¼ bolts
More information*images might vary from actual product (2) wings* (2) metal legs
500BN headboard/bed Assembly Instructions for 40NB, 300, 300nb, 30, 500BN, 500NB, & 530NB Series headboard components () Headboard* *images might vary from actual product () wings* () metal legs headboard
More informationstandard Bed assembly
standard Bed assembly upholstered side rails hardware You will need: (6) 1 x 5/16 bolts (6) 1¼ washers phillips screwdriver flat head screwdriver pliers *Open all hardware packets before proceeding. bed
More informationNo: /18 rev. 1 Installation Instructions Instructions d Installation Instrucciones de Instalación
Wattstopper Outdoor PIR Motion Sensors No: 24259 04/18 rev. 1 Installation Instructions Instructions d Installation Instrucciones de Instalación Catalog Numbers Les Numéros de Catalogue Los Números de
More informationMODEL RTA - B001N MODEL RTA-B001N
MODEL RTA - B001N MODEL RTA-B001N Spanish INSTRUCCIONES DE ENSAMBLAJE. MODELO RTA - B001N Gracias por comprar uno de nuestros productos. Por favor lea cuidadosamente las instrucciones de ensamblaje antes
More informationUniversal TechBox Series
Instruction Sheet Universal TechBox Series UTB-A2-14 / UTB-HR-A2-14 THANK YOU Thank you for purchasing a Universal TechBox UTB-A2-14 / UTB-HR-A2-14. Please read these instructions thoroughly before installing
More informationFollow these precautions to ensure safe installation and mounting of your fl at panel TV.
flat panel solutions Wall Mount for LCD, Plasma, and LED Displays Installation Manual MAF85BKR Fits TVs 37-60 Maximum Load Capacity 165 lb (75 kg) Thank you for choosing the RCA MAF85BKR Universal Flat
More informationNo: /16 rev. 1 Installation Instructions Instructions d Installation Instrucciones de Instalación DESCRIPTION
Wattstopper DLM - Digital Input/Output Interface No: 24642 09/16 rev. 1 Installation Instructions Instructions d Installation Instrucciones de Instalación Catalog Number Numéro de Catalogue Número de Catálogo:
More informationCA3500 / CAS3500 Classic Arbor OWNER S MANUAL
OWNER S MANUAL WARNING Repair or replace broken parts immediately. Suncast is not responsible for damage caused by weather or misuse. Avoid excess heat from any auxiliary source. CA3500 / CAS3500 Classic
More information42 rue Marcel Maskinongé Québec J0K 1N0. EN VIGUEUR LE 1 er JANVIER 2017 EFFECTIVE JANUARY 1 st, 2017
Mobiliers Masson 42 rue Marcel Maskinongé Québec J0K 1N0 EN VIGUEUR LE 1 er JANVIER 2017 EFFECTIVE JANUARY 1 st, 2017 F.A.B. rue Marcel, Maskinongé Québec Téléphone / Phone: (819) 227-2948 Fax: (819) 227-2632
More informationSun StorEdge D2 Array Cabinet Installation Guide
Sun StorEdge D2 Array Cabinet Installation Guide Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U.S.A. 650-960-1300 Part No. 816-1696-11 February 2002, Revision A Send comments about
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS NT-MG1344 High-Gloss Black Metal and Glass TV Stand Safety information and specifications...2 Tools needed...3 Parts...3 Hardware...4 Assembly instructions...5 Safety information
More informationAssembly Instructions Instructions d assemblage Instrucciones de Ensamblaje
register your new purchase online www.sauder.com DO NOT RETURN YOUR UNIT TO THE STORE Contact us first NE PAS RAPPORTER L ÉLÉMENT AU MAGASIN Nous contacter en premier NO DEVUELVA SU UNIDAD A LA TIENDA
More informationnwh300/nwh300c/nrkrwh300/nrkrwh300c
SAFETY INSTRUCTIONS nwh300/nwh300c/nrkrwh300/nrkrwh300c rough-in installation read and save these instructions 12. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION VESA: 50X50 mm/2x2" 75X75 mm/3x3" 100X100 mm/4x4" MODEL:MD2463 Please read this instruction carefully before installation. Fits for most 10-26 inches Plasma, LCD and LED TVs. Weight
More informationJR HOME COLLECTION. HALL TREE Assembly Instructions. Item#: IF-SH-205-MH IF-SH-205-ES
JR HOME OLLETION HLL TREE ssembly Instructions Item#: IF-SH-205-MH IF-SH-205-ES RED & SVE THESE INSTRUTIONS arefully read and review before assembling, installing, operating or maintaining this product.
More informationTHANK YOU FOR PURCHASING OUR STUDIO RTA CREATION STATION
THANK YOU FOR PURCHASING OUR STUDIO RTA MODEL# 20672 IF YOU REQUIRE ANY ASSISTANCE WITH ASSEMBLY, PARTS, OR INFORMATION ON OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE: www.studiorta.com OR CALL OR WRITE THE
More informationVISIT THE LIFETIME WEB SITE: **U.S. and Canada customers ONLY** IF ASSISTANCE IS NEEDED, DO NOT CONTACT THE STORE!!!
VISIT THE LIFETIME WEB SITE: WWW.LIFETIME.COM **U.S. and Canada customers ONLY** IF ASSISTANCE IS NEEDED, DO NOT CONTACT THE STORE!!! CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865 HOURS: 7:00
More informationASSEMBLY INSTRUCTIONS Last Updated
ASSEMBLY INSTRUCTIONS Last Updated 05.08.08 5 & 10 Row Bleacher Instructions for all bleacher lengths. Guardrail and toe board installation included. 90653 9 Long 5 Row Bleacher 90654 15 Long 5 Row Bleacher
More informationAquatic Specialties Manufacturing. Cover Butler Installation & Use Manual
Aquatic Specialties Manufacturing Cover Butler Installation & Use Manual The Cover Butler adjusts to fit most square/rectangular spas up to 99 in width. When assembled it forms a rectangular shape. The
More informationASYX 2.0 S3-S4-L3-L4-L5-L6 Wall Installation Instructions
Brand Logo reversed out of black INS # ASYX 2.0 S3-S4-L3-L4-L5-L6 Wall Installation Instructions IMPORTANT: Read carefully before installing fixture. Retain for future reference. Risk of Electric Shock.
More informationOne Arm Articulating TV Wall Mount
One Arm Articulating TV Wall Mount Item No: 63607068/63607107/63607139 MIN:3.07 in / 78 mm MAX:21.65 in / 550 mm MIN: 2.95 x 2.95 in / 75 x 75 mm MAX:3.9 x 3.9 in / 100 x 100 mm Congratulations on your
More informationItem #: Versa 18 Wall Unit
For factory use only Option 1 Option Option 3 Item #: 38435833 Versa 18 Wall Unit Congratulations on your latest Atlantic purchase. Follow these instructions, and you ll have this new product assembled
More informationSpa & Hot Tub Necessities. Cover Butler Cover Lifter Installation & Use Manual
Spa & Hot Tub Necessities Cover Butler Cover Lifter Installation & Use Manual The Cover Butler adjusts to fit most square/rectangular spas up to 99 in width. When assembled it forms a rectangular shape.
More informationInstructions INSTRUCTIONS INSTRUCCIONES
an LDI Spaces Company Minneapolis, MN 55428 www.safcoproducts.com Instructions INSTRUCTIONS INSTRUCCIONES 1706 Appliance Hutch Électroménager Huche Aparador De Aparato PRODUCT WARRANTY REGISTRATION is
More informationDM-100 DM-110 DIGITAL MULTIMETERS MULTÍMETROS DIGITALES MULTIMETRES NUMERIQUES MANUAL DE INSTRUCCIONES MANUEL D INSTRUCTIONS
INSTRUCTION INSTRUCTION MANUAL MANUAL MANUAL DE INSTRUCCIONES MANUEL D INSTRUCTIONS DM-100 DM-110 DIGITAL MULTIMETERS MULTÍMETROS DIGITALES MULTIMETRES NUMERIQUES Read and understand all of the instructions
More informationCOMPETITOR CB-610 STANDARD BENCH
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice COMPETITOR CB-610 STANDARD BENCH Hardware Identifier Assembly Instruction Exploded Diagram Parts List
More informationTHANK YOU FOR PURCHASING OUR STUDIO RTA PROJECT STATION
THANK YOU FOR PURCHASING OUR STUDIO RTA MODEL# 50040 BLACK/MAPLE, 50042 PEWTER/CHERRY IF YOU REQUIRE ANY ASSISTANCE WITH ASSEMBLY, PARTS, OR INFORMATION ON OTHER PRODUCTS, PLEASE VISIT OUR WEBSITE: www.studiorta.com
More informationActivate Your xfi Pods from the Xfinity xfi Mobile App
Activate Your xfi Pods from the Xfinity xfi Mobile App This document provides step-by-step instructions on how you can activate your xfi Pods using the Xfinity xfi app for mobile devices. If you have additional
More informationInstruction Sheet VDM-200-T. Tilt Wall Mount
Instruction Sheet VDM-200-T Tilt Wall Mount THANK YOU Thank you for purchasing the VDM-200-T tilt wall mount. Please read these instructions thoroughly before installing or assembling this product. PRODUCT
More informationInstruction Sheet. VDM Series. Tilt Low Profile Mount
Instruction Sheet VDM Series Tilt Low Profile Mount VDM-400-T-LP VDM-600-T-LP VDM-800-T-LP THANK YOU Thank you for purchasing the Vision Display fixed low profile wall mount. Please read these instructions
More informationSierra OUTDOOR DESIGNS
AND 8 INCH GRILL CABINET WITH ADAPTER KIT For questions, problems or missing parts, please contact Cardinal Systems, Inc. Customer Service 8:00 a.m. - 5:00 p.m., EST Monday-Friday 570-385-733 customerservice@cardinalsystemsinc.com
More informationSLW 6 Channel Letter Brake. User Guide. Operation and Mounting Instructions
SLW 6 Channel Letter Brake User Guide Operation and Mounting Instructions Scope This document describes the operation and mounting instructions for the SLW 6" Channel Letter Brake. Please read all instructions
More informationBrocade SilkWorm Switch and SilkWorm Director Sun Rackmounting Guide
Brocade SilkWorm Switch and SilkWorm Director Sun Rackmounting Guide For Mounting Brocade SilkWorm 3200, 3250, 3800, 3850, 3900, 4100, and 200E Switches and SilkWorm 12000, 24000, and 48000 Directors in
More informationINSTRUCTION BOOK FOR. Parallax 0.8 Screen
INSTRUCTION BOOK FOR Parallax 0.8 Screen Included Hardware Large Wall Bracket (47" Long) Installation screws not included Quantities vary by screen size: Screens 80" and smaller viewing width = 1 Screens
More informationBASE & WALL CABINET SETUP GUIDE BY SUNSTONE
BASE & WALL CABINET SETUP GUIDE BY SUNSTONE Read all instructions before you install cabinet. Very important to follow each step in order as detailed in this Instruction Guide!!! To installer or person
More informationAssembly Instructions & User s Manual 6 Piece Folding Dining Set FSMVPT2084
& User s Manual 6 Piece Folding Dining Set FSMVPT2084 Please keep this instruction manual for future reference Customer Service: (888) 922-2336 7:00 am to 12:00 am CST (daily) Live Chat at: www.academy.com
More informationINSTRUCTION BOOK FOR. UTB Contour
INSTRUCTION BOOK FOR UTB Contour Included Hardware Tools Required for Installation Large (47 ) (1) Screens under 104" in viewing width (2) Screens 104" and over in viewing width Phillips Screwdriver Pencil
More informationM2M Cellular Signal Amplifier
CSB.01 M2M Cellular Signal Amplifier Operator s Manual and Installation Guide www.taoglas.com Designed & Manufactured in The U.S.A. Contents 1. Overview 3 2. Parts List 3 3. Installation Guide 4 4. Installation
More informationSpa & Hot Tub Necessities. Cover Removal System Installation & Use Manual
Spa & Hot Tub Necessities Cover Removal System Installation & Use Manual SET-UP AND ASSEMBLY BEFORE BEGINNING ASSEMBLY, CAREFULLY READ THE FOLLOWING INFORMATION AND INSTRUCTIONS: Place all parts in a cleared
More informationInstruction Sheet. VDM Series FIXED & TILT WALL MOUNT
Instruction Sheet VDM Series FIXED & TILT WALL MOUNT VDM-400-F & VDM-600-F VDM-400-T & VDM-600-T THANK YOU Thank you for purchasing a Vision Display fixed or tilt wall mount. Please read these instructions
More informationSloped Top Shop Desk and Cabinet Conversion Kit Assembly Instructions
Sloped Top Shop Desk and Cabinet Conversion Kit Assembly Instructions IMPORTANT - PRODUCT LIABILITY INFORMATION Read all instructions before proceeding with installation. Vital product information pertaining
More informationInstallation Instructions Lower Cargo Rack Bracket
Installation Instructions Lower Cargo Rack Application: Jeep Wrangler 2003 Current Part Number: 41437 US Patent 6799706 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question.
More informationVinyl Fence Gates. Assembly and Installation Instructions PLEASE READ OWNER'S MANUAL COMPLETELY BEFORE ASSEMBLING YOUR FENCE.
Vinyl Fence Gates Assembly and Installation Instructions PLEASE READ OWNER'S MANUAL COMPLETELY BEFORE ASSEMBLING YOUR FENCE. ALL STATED SIZES ARE NOMINAL DIMENSIONS. 34106493BOM V2 11/12 Models 73013273
More informationINSTRUCTION BOOK FOR. Da-Snap Screen
INSTRUCTION BOOK FOR Da-Snap Screen Included Hardware Large Wall Bracket (47" Long) Installation screws not included Quantities vary by screen size: Screens 80" and smaller viewing width = 1 Screens over
More informationButterfly Hinge Standard & Heavy Duty PLEASE READ OWNER'S MANUAL COMPLETELY BEFORE INSTALLING YOUR HINGE KIT.
Butterfly Hinge Standard & Heavy Duty Installation Instructions PLEASE READ OWNER'S MANUAL COMPLETELY BEFORE INSTALLING YOUR HINGE KIT. For use with Vinyl, Aluminum and Wood. Heavy Duty Butterfly Hinge
More informationInstallation Instructions Tailgate Rack Bracket
Installation Instructions Tailgate Rack Application: Jeep Wrangler 1986 Current Part Number: 41411 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question. Click here for more
More informationSS/SW3230RTA Assembly Instructions Ready to Assemble Multimedia Lectern
650 Anthony Trail, Suite D, Northbrook, IL 60062 Phone: (800)267-5486 Fax: (800)267-5489 www.ampli.com - info@ampli.com SS/SW3230RTA Assembly Instructions Ready to Assemble Multimedia Lectern Thank you
More informationIn Place Roll Groover
915 In Place Roll Groover OPERATOR S MANUAL Français 15 Para el castellano vea la página 31 WARNING! Read this Operator s Manual carefully before using this tool. Failure to understand and follow the contents
More informationINSTALLATION MANUAL ES-SUB-WIRELESS-KIT ES-SUB-WIRELESS-RCVR
INSTALLATION MANUAL ES-SUB-WIRELESS-KIT ES-SUB-WIRELESS-RCVR FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
More informationCS-28MM1030-GRY ASSEMBLY, CARE & USE INSTRUCTIONS
CS-8MM030-GRY ASSEMBLY, CARE & USE INSTRUCTIONS Questions, problems, missing parts? Before returning to your retailer, call our customers service department at -855-57-044 8 a.m. - 8 p.m., EST, Monday-Friday.
More informationModels 2230 and 2240
Models 2230 and 2240 Overview... 2 Tools Needed... 2 Hardware...3 Assembly... 4-13 Installation... 14 Drawer Removal... 15 Operation... 15 Maintenance... 15 Accessories... 16 Limited Warranty... 16 Perform
More informationInstallation Instructions Factory Style Bow Kit
INSTALLATION TIME Installation Instructions Factory Style Bow Kit SKILL LEVEL Vehicle Application: Jeep Wrangler JK 2 Door 2007 Current Part Number: 55000 Compatible with original equipment soft tops,
More informationInstruction Sheet. VDM Series FIXED & TILT WALL MOUNT
Instruction Sheet VDM Series FIXED & TILT WALL MOUNT VDM-800-F VDM-800-T THANK YOU Thank you for purchasing the Vision Display fixed and tilt wall mounts. Please read these instructions thoroughly before
More informationVersaRail Gate Kit. freedomproduct.com. To register your product, please visit: INSTALLATION INSTRUCTIONS
VersaRail Gate Kit INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Refer to manufacturers safety instructions when operating any tools. To register your product, please visit:
More informationHUSTLER 7' & 8' POOL TABLE ASSEMBLY INSTRUCTIONS
HUSTLER 7' & 8' POOL TABLE ASSEMBLY INSTRUCTIONS Please Do Not Hesitate to Contact Our Consumer Hotline at 800-759-0977 with Any Questions That May Arise During Assembly or Use of This Product! NG2515PB/NG2520PB
More informationInstruction Sheet REB SERIES. Rotating Sliding Base REB18
Instruction Sheet REB SERIES Rotating Sliding Base REB14 REB18 THANK YOU Thank you for purchasing the REB Series Rotating Sliding Base. Please read these instructions thoroughly before installing this
More informationNo: /17 rev. 1 Installation Instructions Instructions d Installation Instrucciones de Instalación
Wattstopper Digital Lighting Management Open Loop Multiple Zone Photosensor No: 24615 02/17 rev. 1 Installation Instructions Instructions d Installation Instrucciones de Instalación Catalog Numbers Les
More informationINSTALLATION INSTRUCTION LED Wall Sconce WS-21718
WS-21718 WARNING IMPORTANT: NEVER attempt any work without shutting off the electricity. - Read all instructions before installing. - System is intended for installation by a qualified electrician in accordance
More informationLM600 Landmark Permanent Blind
LM600 Landmark Permanent Blind Get parts online at www.huntriversedge.com P/N: 23033 REV1: 02/23/16 2016 RETI All Rights Reserved INTRODUCTION Landmark Permanent Blinds are engineered with you the hunter
More informationTVB-2 INSTRUCTION SHEET. Test Verification Box
TVB- INSTRUCTION SHEET Test Verification Box V.07.08 DECLARATION OF CONFORMITY Manufacturer: Address: Product Name: Model Number: Associated Research, Inc. 3860 W. Laurel Dr. Lake Forest, IL 60045, USA
More informationInstallation Instructions Hinged Roof Rack
Installation Instructions Hinged Roof Rack Application: Jeep Wrangler Unlimited 2004 - Current Part Number: 41435-01 www.bestop.com - We re here to help! Visit our web site and click on Ask a Question
More informationOWNER S MANUAL: Adjustable Height Wall Rack
OWNER S MANUAL: Adjustable Height Wall Rack Keep this information for further reference. Thank you for purchasing a NavePoint product. Please examine the product for any damaged parts. If any part is damaged
More informationTilting Wall Mount Fits 37" to 70" Flat Panel TVs Model No: DCD13020
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Lot Number: Date: Tilting Wall Mount Fits 37" to 70" Flat Panel TVs Model No: DCD1300 MIN:7.87
More informationM2M. Overview. Passive. volts DC. AC power. eliminating any
WRE2710 S Operator s Manual and Installation Guide: M2M Machine to Machine Overview The WRE2710 Wirelesss Network Range Extender is a high performance, microprocessor controlled, bidirectional RF amplifier
More informationPOWERHOUSE BENCH PHC -265
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction POWERHOUSE BENCH PHC -265 Parts List Warranty Ordering Parts
More informationWARNING COM. Full Platform Bed B COM00. ameriwoodhome.com Follow Ameriwood Home. Keep this Assembly Manual for future reference
B3400 Keep this Assembly Manual for future reference WARIG Unit can tip over causing severe injury or death. - Anchor unit to stud in wall - Do ot allow children to climb on unit - Put heavy items on lower
More information15 Amp Digital High Frequency PWM Motor Speed Controller SPD-315-D and SPD-315-DS
15 Amp Digital High Frequency PWM Motor Speed Controller SPD-315-D and SPD-315-DS The SPD-315-D(S) PWM controller allows you to control the speed of a motor, brightness of a lamp or other load using a
More informationModels 2130 and 2140
Models 2130 and 2140 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-10 Installation...11 Operation... 11 Maintenance... 12 Accessories...12 Limited Warranty... 12 Printed in USA 2007 Perform
More informationInstallation and Assembly: Recessed Cable Management and Power Storage Accessory Box
Installation and Assembly: Recessed Cable Management and Power Storage Accessory Box Models: IBA3, IBA3-W 2300 White Oak Circle Aurora, Il 60502 (800) 865-2112 Fax: (800) 359-6500 www.peerlessmounts.com
More information22U 36in Depth Enclosed Server Cabinet with Casters
U 36in Depth Enclosed Server Cabinet with Casters RK36BKF -Rev SW *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del
More informationInstallation & Assembly: Suspended Ceiling Kit
Installation & ssembly: Suspended Ceiling Kit Model: CMJ450 Max UL Load Capacity: 250 lb (113 kg) Compatible model/series* EC* EXT* DD* 2300 White Oak Circle urora, Il 60502 (800) 865-2112 Fax: (800) 359-6500
More information8150 Variable-Height Keyboard Slide
Note: Rockler may not carry all products and/or sizes listed in this vendor's publication KNAPE 8150 Variable-Height Keyboard Slide KV 8150 Major Dimensions and Mounting Hole Locations 12" - 24837 14"
More informationT9i Treadmill. Assembly Instructions
T9i Treadmill Assembly Instructions Congratulations... and welcome to the world of The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up
More informationInstallation Instructions. Monitor Roll Stand
Installation Instructions Monitor Roll Stand w w w. a m i c o. c o m Preface Important, Please Read Carefully Thank you for your purchase with Amico. This unit is designed for long lasting performance,
More informationroom essentials >> assembly instructions H 1 4 drawer chest DPCI # (Black Woodgrain) DPCI # (Espresso)
room essentials 4 drawer chest DPCI # 249-05 - 0103 (Black Woodgrain) DPCI # 249-05 - 0106 (Espresso) >> assembly instructions 92335 H 1 FREE! Do not go back to your store! we will help you! Missing or
More informationHomeowners Guide. Cast Iron Kitchen Sinks
Homeowners Guide Cast Iron Kitchen Sinks K-5800, K-5802, K-5805, K-5809, K-5810, K-5813, K-5814, K-5815, K-5823, K-5832, K-5834, K-5837, K-5838, K-5839, K-5847, K-5848, K-5850, K-5852, K-5863, K-5864,
More informationDirect Tapping Machine Operator s Manual Manual del operador para aterrajar
TM1100 Direct Tapping Machine Manual del operador para aterrajar DIRECT TAPPING MACHINE - TM1100 COMBINATION TAPPING & DRILLING MACHINE - CDTM1100, CDTM2100 WARNING: Read and fully understand all instructions
More informationUnirac Flat Flashing INSTALLATION MANUAL
Unirac Flat Flashing INSTALLATION MANUAL 2011 by Unirac, Inc. All rights reserved. Pub 110301-1ii, March 2011 A HILTI GROUP COMPANY R 1411 Broadway Boulevard NE Albuquerque, NM 87102-1545 USA IMPORTANT!
More informationModels 2030 and 2040
Models 2030 and 2040 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-8 Installation... 9 Operation... 9 Maintenance... 10 Accessories... 10 Limited Warranty... 10 Document # 101290 0607 Printed
More informationReady-To-Assemble VersaRail INSTALLATION INSTRUCTIONS
Ready-To-Assemble VersaRail INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Refer to manufacturers safety instructions when operating any tools. To register your product, please
More informationPRIMO 56" FOOSBALL TABLE ASSEMBLY INSTRUCTIONS
PRIMO 56" FOOSBALL TABLE ASSEMBLY INSTRUCTIONS NG1035 THANK YOU! Thank you for purchasing this product. We work around the clock and around the globe to ensure that our products maintain the highest possible
More informationOwner s Manual. FT100X. 4ft Folding Football Table. Manual version 2.1
Owner s Manual. FT100X 4ft Folding Football Table www.viavito.com Manual version 2.1 Congratulations on purchasing your very own FT100X Folding Football Table You have chosen a high-quality, safe and innovative
More informationInstallation & Assembly: Two Piece Suspended Ceiling Plate
Installation & ssembly: Two Piece Suspended Ceiling Plate Model: CMJ453 Max UL Load Capacity: 250 lb (113 kg) Compatible model/series* EC* EXT* DD* 2300 White Oak Circle urora, Il 60502 (800) 865-2112
More information25U 36 in. Knock-Down Server Rack Cabinet with Casters
25U 36 in. Knock-Down Server Rack Cabinet with Casters RK2536BKF -Rev SW *actual product may vary from photos FR: Guide de l utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES:
More information10 Amp Digital PWM Motor Speed Controller CV-2110-HD and CV-2110-HDS
10 Amp Digital PWM Motor Speed Controller CV-2110-HD and CV-2110-HDS The Analog / Digital PWM controller allows you to control the speed of a motor, brightness of a lamp or other device using an analog
More information120x165mm. 85x165mm TEMPLATE. ELECTRONIC DEADBOLT model no.: & & Toll-free Number:
20x65mm 85x65mm ELECTRONIC EABOLT FOR BACSET 2 3/4" ( 70 mm) FOR BACSET 2 3/8" ( 60 mm) Ø 2 /8" ( 54 mm ) Toll-free Number: -800-268-659 IMPORTANT: Please read this manual carefully before installing this
More informationYour Super Simple Guide to Setting Up Your
Your Super Simple Guide to Setting Up Your Canopy Desk Product Number: NAH006c About Canopy Furniture Lot Number: Date Purchased: / / Decorating your home should be fun and easy. The classic styles of
More informationSafety Awareness Barriers
INSTALLATION INSTRUCTIONS FOR These safety awareness barriers are ideal for use in the manufacturing industry to provide a physical and visual means to warn people that hazards exist beyond the barrier.
More informationInstruction Sheet. VRS Series. Vertical Rackmount system for multiple cable/satellite receivers
Instruction Sheet VRS Series Vertical Rackmount system for multiple cable/satellite receivers THANK YOU Thank you for purchasing the VRS Vertical Rackmount System. Please read these instructions thoroughly
More informationCOMPETITOR WM-203 COMBO BENCH
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier COMPETITOR WM-203 COMBO BENCH Assembly Instruction Exploded Diagram Parts List
More informationBalishutters. INSTALLATION guide FOR L-FRAME MOUNT INSTALL OPTIONS B OR C
Balishutters INSTALLATION guide FOR L-FRAME MOUNT INSTALL OPTIONS B OR C Tools needed for installation Drill Phillips bit 1/8" drill bit 4. Hammer (preferably hard plastic) 5. Level 6. Phillips-head screwdriver
More informationInstallation Instructions BestRail Ladder Rack Must be used with BestRail Accessories: Overhead Rack
Installation Instructions BestRail Ladder Rack Must be used with Accessories: 42791 Can be used with Accessories: 42793 Tie Down 42794 Retractable Tie Down The channels in the Ladder Rack are the same
More informationVDM-2X1-WM & VDM-3X1-WM MONITOR WALL MOUNTS
Instruction Sheet VDM-2X1-WM & VDM-3X1-WM MONITOR WALL MOUNTS VDM-2X1-WM VDM-3X1-WM THANK YOU Thank you for purchasing the VDM-2X1-WM or VDM-3X1-WM monitor wall mounts. Please read these instructions thoroughly
More informationSANPERA I. Player`s Handbook
SANPERA I SANPERA I Player`s Handbook TM SANPERA I Welcome Thank you for purchasing the SanperaTM I foot controller for your VYPYR amplifier. We are certain you will enjoy having the control of your VYPYR
More informationCamaro Performance Decals - Coupe
Kit Content Hood Decal (V6 or V8) Rear Compartment Lid (CPE) Decal Spoiler Decal Door Lower Decal LH Door Lower Decal RH NOTE: THESE DECALS CAN BE DIFFICULT TO INSTALL. IN ORDER TO ASSURE A SATISFACTORY
More informationTilting Flat Panel Wall Mount Installation Guide
Tilting Flat Panel Wall Mount Installation Guide Model: A580TM Easy installation Built-in level for easy positioning Safety bolts lock the TV on the mount Easy to adjust tilt angles: +5 to -15 degrees
More informationDS600048C-CL. 48" Sliding Linear Shower Door. 1174~1199mm (46-3/16"~47-3/16")
DS000C-CL " Sliding Linear Shower Door 0mm(-/") ~99mm (-/"~-/") Dimension of shower door: (~99) x 0mm(H) / (-/"~-/") x -/"(H) Profile adjustment: +mm/" Rev. April,0 DS0000C-CL 0" Sliding Linear Shower
More information