P-DR1W-48 P-DR1W-60 OWNER S MANUAL

Transcription

1 P-DRW-48 P-DRW-0 OWNER S MANUAL SHOWER ENCLOSURES PEOPLE REQUIRED IT IS MANDATORY TO HAVE A WALL STUD ON EACH SIDE OF THE SHOWER UNIT TO SECURELY FASTEN THE RAIL TO THE WALLS. P00 0.0

2 TABLE PANNEAU OF CONTENTS FIXE / FIXED PANEL PARTS LISTING... 3 PROVIDED HARDWARE... 4 GLASS PANEL DIMENSIONS... 4 REQUIRED TOOLS AND MATERIALS... 4 GASKET INSTALLATION... 5 RUNNING RAIL.... GLASS HOLDERS... GLASS CLIPS... FIXED PANEL PLACEMENT... 8 FIXED PANEL PLACEMENT (CONTINUED)... 9 THRESHOLD... 9 WALL BRACKETS... 0 SLIDING DOOR... SLIDING DOOR (CONTINUED)... STRAIGHT HANDLE... GASKETS INSTALLATION... STOPPERS... 4 SILICONE... 4 GENERAL INSTRUCTIONS - Read this manual carefully and completely before proceeding. - Product are subject to change without notice. Use the installation instructions supplied with the product. SAFETY - It is recommended that you wear safety glasses at all times during the installation. - At all times, people are required for this installation. WATERPROOFING - No sealant is required inside the shower. - All models are equipped with transparent sealing gaskets. - For models with wall jambs, if your shower door is to be installed over ceramic tiles, the tiles should lay completely under the wall jambs. MAINTENANCE - Never use scouring powder pads or sharp instruments on metal pieces or glass panels. - An occasional wiping down with a mild soap diluted in water is all that is needed to keep the panels and aluminum parts looking new. - We recommend wiping the glass panels with a squeegee after each use.

3 PARTS LISTING ITEM PARTS QTY RUNNING RAIL WALL BRACKET 3 STOPPERS 4 GLASS HOLDERS 5 TWIN ROLLERS PAIRS SLIDING DOOR PANEL FIXED PANEL 8 STRAIGHT HANDLE 9 GASKET (DOOR) 0 GASKET (FIXED PANEL) BOTTOM GLASS CLIP GASKET (GLASS CLIP) BOTTOM GUIDE 4 GASKET (BOTTOM GUIDE) 5 THRESHOLD DOOR PANEL SIDE GASKET DOOR PANEL BOTTOM GASKET 3

4 HARDWARE ITEM HARDWARE QTY 8 #-3 SELF-THREADING SCREW 4 9 #- SELF-THREADING SCREW 0 HEX KEY 3mm HEX KEY mm (/3 ) TOOLS * HACKSAW SCREWDRIVERS DRILL /4 & /8 DRILL BITS SILICONE If the shower panels are to be assembled on ceramic tiles, use a /4 drill bit for ceramic tiles. PENCIL CUTTING PLIER TAPE MEASURE LEVEL MALLET BLOCK 4

5 GASKET INSTALLATION A Using the cardboard packaging box as platform, install bottom door gasket () onto door panel () using a block and a mallet. Notice the gasket orientation. A INTERIOR SHOWER SIDE B Place door panel () inside tub to simplify following installation procedures. Ensure placing the panel onto a cushioned surface, such as a towel or card board, to prevent damage either to the panel or the tub. B Thoroughly clean the edge of the fixed panel (). Split the door gasket (9) in two and apply the smaller half of the gasket on the edge of the fixed panel. 0 INTERIOR SHOWER SIDE 5

6 RUNNING RAIL 3 A Position the stoppers (3) on the running rail () as illustrated. Secure them temporarily in place. B Position the wall brackets () on the running rail () as illustrated. Secure them temporarily in place. -

7 3 GLASS HOLDERS Fasten the running rail () to the fixed panel () with the glass holders (4). Secure them temporarily in place. Ensure that the running rail () is at the highest possible position in reference to the holes of the xed panel (). 4 4 GLASS HOLE WASHER 4 GLASS CLIPS Insert bottom gaskets () in the bottom glass clips () and (). Position the bottom glass clip and bottom guide xed panel as illustrated. / (38 mm) FLUSH WITH GLASS INTERIOR SHOWER SIDE

8 5 FIXED PANEL PLACEMEMENT 5A The bottom guide () can hang off the threshold (B) as long as it can be well-fastened. Position the fixed panel assembly () on threshold of base (B) as shown. INTERIOR SHOWER SIDE Adjust the fixed panel (), by way of the running rail (), so as to force the gasket (0) against the wall. B / max (.mm) 0 B 5B Ensure that the running rail () is level and that the fixed panel () is square. If a horizontal correction is required, adjust and level the glass fasteners (4)

9 5 CONTINUED 5C M a rk the s c re w lo c a tio ns fo r the w a ll b ra c ke ts () on the walls on both sides of shower as well as the placement of the bottom glass clips () (). THRESHOLD S A 5 Remove the fixed panel assembly so as to allow placement of the threshold (5) onto the base. Ensure that a bead of silicone (S) is applied to the underside of the threshold before installing. A 5 B Secure glass clips () () with self-drilling screws (9). 9 9 B 9

10 WALL BRACKETS A Mark the screw locations on the walls on both sides of shower. Remove the running rail () fro m the w a ll b ra c ke ts ( ). D rill ho le s in w a lls until wall stud is reached with a drill bit intended for ceramic tiles. WALL STUD Fasten the wall brackets () with #-3 (8). 8 B Insert fixed panel () back, ensuring that it s placed in the bottom glass clips () (). Slide expander (E) over wall bracket () and fasten set screws E 0

11 8 SLIDING DOOR 8A 5 Assemble the top rollers (5) to the door panel () as illustrated. INTERIOR SHOWER SIDE 8B Install sliding door () ensuring that rollers (5) are fixed over the running rail (). 5 Ensure that sliding door () is placed within the bottom guide ().

12 8 CONTINUED 8C 5 WASHER Install bottom rollers, making sure that they are tangent to the running rail (). Through the use of the nonconcentric washers, adjust rollers so that the sliding door panel is parallel to the running rail. 5 WASHER GLASS HOLE 9 HANDLE See sheet for installation and install the handle as shown. 8 Model illustrated B

13 0 GASKETS INSTALLATION 0A Thoroughly clean the edge of the sliding door, closest to the side where the handle is located. Apply the door gasket (9) to this edge of the sliding door (). 9 0A INTERIOR SHOWER SIDE 0B Install door side gasket () onto sliding door panel (). 0B TOP BOTTOM

14 STOPPERS 0 Ajuster le positionnement des butoirs (3) afin d obtenir une ouverture ainsi qu une fermeture optimale de la porte coulissante. Assurer que le joint de rétention (9) de la porte coulissante s écrase contre le mur. 3 3 DOOR CLOSED 9 Adjust the position of the stoppers (3) so as to ensure a maximum opening and closing range. Ensure that the sliding door gasket (9) is forced against the wall. DOOR OPEN SILICONE Apply silicone between the bottom of the fixed panel and the threshold of the base. Silicone application along the length of the threshold is also suggested. In both cases, it is done from the outside of the shower area. APPROX. 3 (. mm) HOURS 4