ANGLE AND FLAT BAR LINE ABL-74T

Size: px
Start display at page:

Download "ANGLE AND FLAT BAR LINE ABL-74T"

Transcription

1 ANGLE AND FLAT BAR LINE ABL-74T

2 ABL-74T The ABL-74T is our most economical, entry level machine for punching and shearing angle and flat bar. It has a combination of features requested by our customers. These features include: wheel material feed, wheel measuring, single cut shear, and material weld/ tack station to eliminate material drop. As with all Controlled Automation equipment, the ABL-74T is designed to be rugged, reliable, simple to operate, and easy to maintain

3 Machine Base The base of the ABL-74T is made of a rigid steel framework with a steel plate mounting surface which supports the punch frames, hydraulic power unit, the hold downs, the pinch wheel, and the shear. Most of the plumbing (hydraulic and air) is run inside the machine base for protection, a smaller footprint, and to keep the machine base clean. The hydraulic power unit is mounted to the machine base, to eliminate all plumbing around the machine

4 User Interface The ABL-74T control system has an easy to use interface. As the machine runs, the status of each part or operation changes in real-time. A part list dialog can be displayed to show which parts have been completed or which operations are remaining. The controller can be easily networked to the office computer network for downloading of parts produced in the office or by most drafting and design programs. Parts can also be easily programmed at the machine, even while another part is being run.

5 Diagnostics and Monitoring Screens Using the diagnostics screen the operator is allowed to cycle through the machine processes (shearing, punching, etc..) for each component to ensure the machine is operating correctly. The monitoring screens monitor each of the machine components during it s operation. Internet Diagnostics If your machine has an internet connection, Controlled Automation service technicians can perform diagnostic testing and machine calibration via the internet. Diagnostics screen The Pre-Run Screen Monitoring screen Machine Software The main control software for all equipment comes complete with diagnostics capabilities and monitoring screens. This helps the maintenance personnel trace down any possible problems which may occur with ease. Every input relay and output relay can be checked via the diagnostics software. Every quadrature encoder input and every digital to analog output can also be verified through the software diagnostics. Pre-Run screen The pre-run screen is designed to allow the operator to change certain machine settings before running a part. The operator can choose and verify the tools for the machine, set the materials stock length, change kerfs desired, modify part quantities in a mult, change the material trim length, etc. Completed processes are indicated in red Run Screen During the running of a part or a mult the operator gets visual feedback as to the progress of each part. The machine can be stopped at any time and restarted. Operations can be repeated or skipped. Run Screen

6 Punch Frames Stripper Each punch frame has our unique, automatically against the die while the punch is retracting. This gives better hole quality and improved punch and die life. The machine has two 74 ton punch frames, one for each leg of the angle. Each punch frame has a single punch. The punch has extend and retract limit switches to indicate when the punch has extended through the material and when it has fully retracted. These frames are designed for easy access to the punch and die. This provides quicker hole size change times. Hydraulic Positioning The punch frames are positioned hydraulically using a computer controlled hydraulic valve system. The valve system provides fast, accurate positioning of the punch frames. (stripper removed for this view)

7 Punch diagram in fully extended position Punch Unit PAL-241 PUNCH COUPLING NUT PUNCH 2" X 2" X 3/16" ANGLE 6" X 6" X 1/2" ANGLE MINIMUM GAUGE ANGLE LEG LENGTH MINIMUM GAUGE The punch units are an extremely rugged design, which will provide exceptionally long service. The punch and die holders are machined for locating keys and pins, for use with non-round punches and dies. The frame positioning wheel assemblies are designed to allow the frames to float when punching bent material. This reduces stress on the wheel assemblies providing a long, trouble-free service life. END VIEW DOWN THE LENGTH OF THE MATERIAL 1-1/4" < 2" > 2" < 6" 11/16" + ANGLE LEG THICKNESS 1-1/16" + ANGLE LEG THICKNESS PUNCH INFORMATION NOTE: PUNCH USED ON STANDARD PUNCH STEM IS CLEVELAND PUNCH & DIE FIG. NO. C-770 DIE IS FIG. NO. C-740 TOOLING TO CHANGE PUNCHES NOTE: ALL TOOLING NEEDED TO CHANGE PUNCHES IS SUPPLIED NOTE: A 3/16" ALLEN WRENCH IS NEEDED TO CHANGE DIES NOTE: MAXIMUM TONNAGE FOR THIS STEM IS 74 TONS

8 Single Cut Shear The ABL-74T shear is designed and built to give long trouble free life, but with more features than competitive units. It is a single cut design, which means there is no loss of material when shearing, unlike some competitor s machines. The shear s extra stiff design provides cleaner cuts, with less distortion, and longer shear blade life. A seperate, specially A part chute directs short parts directly into a cart or bin. (Controlled Automation does not supply the cart or bin.)

9 1/2" RADIUS 3/8" RADIUS Male Blade Index To achieve superior cut quality on all angle thicknesses the reversable and indexable male blade is designed with four different radii to help match the cuts with less distortion. The blade may be rotated to accommodate the different material thicknesses and sizes. Blade life is prolonged by using all four sides. The blade is large enough to allow it to be sharpened to give even longer life. Male Angle Iron Blade Male Flat Bar Blade 3/16" RADIUS 1/4" RADIUS

10 Manual Controls The operator control station has manual switches that may be used by the operator to turn on the AC power, turn on the hydraulics, halt the machine, move the units, convey the material, and other machine functions.

11 Wheel Measuring This material length measuring uses a single servo powered pinch wheel to pull the material through the machine on a nonpowered V-roll conveyor. A separate measuring wheel contacts the material and rotates as the material is pulled through by the powered pinch wheel. The measuring wheel is located is combined with the weld station to eliminate material drop.

12 Weld / Tack Station The Weld/Tack Station is designed for a continuous feed of material through the machine and to eliminate the drop on the trailing end of the material. As the trailing end of the material passes the weld station the material will stop automatically and allow the operator to tack on an addition piece of material to continue the feeding into the machine. The operator can choose to leave the weld in the part or shear it out as a small piece of scrap.

13 (20 Storage and load conveyor) Hydraulic Power Unit The hydraulic power unit is only when needed. This keeps the hydraulic oil from heating which reduces the chance of hydraulic system failure. The hydraulic power ease of maintenance. The unit is mounted to the machine base, to eliminate any plumbing on the 20 Storage And Loading Conveyor The purpose of the optional in-feed conveyor and to load this material onto the in-feed conveyor for processing. The operator can load a piece of material from the load conveyor to the in-feed with merely the push of a button. A bundle of material can be placed on a customer supplied bundle rack (drawings supplied by Controlled Automation) and material rolled onto the loading conveyor. The loading conveyor is indexed by the operator as each piece is loaded. When the table is full the operator need only roll another piece onto the loading conveyor as a piece is processed through the machine. This system frees up the crane or lift trucks while the material is being processed. This also allows the loading conveyor to be staged with different material as the machine is running. (Controlled Automation does not supply the bundle rack)

14 Powered Out-Feed Conveyor and Work Surface This is an optional 5 long conveyor located on the out-feed side of the shear. It is powered. One side of its rolls can be lowered and used as a work surface by the operator. This conveyor, due to its close proximity to the operator, cannot be used as a dump conveyor. Powered Out-Feed and Dump Conveyor This optional 15 conveyor is a V-style chain driven conveyor used to automatically or manually convey and dump longer parts at drop locations. The conveyor automatically dumps parts into a drop location based on the part s length. The computer senses the location of the part as it moves down the conveyor by signals from photo eyes which are mounted down the length of the conveyor. When the part gets to the appropriate drop location the entire conveyor roller bed will pivot, dropping the material at the drop location. If a drop location becomes full a switch can be set so the next appropriate drop location can be used. The machine will continue to advance and punch the material as the dump conveyor is operating up to the point the advancing material interferes with the dump conveyor or the material needs to be sheared. Up to four dump conveyors can be tied together for a 60 material discharge and dump out-feed. The dump conveyor is always used with the 5 powered out-feed conveyor and work surface. In most circumstances the customer will build simple skid type racks to catch the material. This allows a chain to be wrapped around the material or access to the material by a fork truck. 5 Non Powered Out-Feed Conveyor and Work Surface This is an optional 5 long conveyor located on the out-feed side of the shear. It is not powered. One side of its rolls can be lowered and used as a work surface by the operator. This conveyor, due to its close proximity to the operator, cannot be used as a dump conveyor. up position for short clips down position for longer parts machine base 10 non powered out feed conveyor Powered In-Feed Auxilary Pinch Wheel An optional powered drive wheel assembly can be added to the in-feed conveyor to assist the operator in initially bringing the material into the machine for the start of a part run. It is controlled by a manual switch and is disabled during the part run. The powered in-feed pinch wheel is normally used for in-feed conveyors that are 60 long to assist the operator with heavy material. This option is also used when the in-feed and machine base are on opposite sides of a wall. 15 powered out-feed and dump conveyor (shown with customer provided catch racks) 10 Non Powered Out-Feed Conveyor This optional 10 long V-style conveyor is not powered. It has a short section of rolls that can be pivoted up, to allow short clips to fall directly into a material catch cart or bin. Longer parts are supported by the entire conveyor. (Controlled Automation does not supply the cart or bin) 5 powered out-feed and work surface

15 ABL-74T Production Specifications Material positioning speed 0 TO 180 ft/min Accuracy 1/32 electronically Punch capacity 74 tons Maximum hole size 1-9/16 Single-cut shear capacity 6 x 6 x 1/2 angle, 1/2 x 6 bar, 215 tons Maximum length of material 40 (for standard machine) (20 or 60 optional) Minimum length of material 6 Angle Maximum angle size 6 x 6 x 1/2 Minimum angle size 1-1/4 x 1-1/4 x 1/8 Flat Bar Maximum bar size 1/2 x 6 Minimum bar size 3/16 x 2 Hydraulic Power Unit Electric Motor Pump Reservoir RPM 27 GPM, 4500 PSI max 70 gallons For more complete information on this or any of our machines, contact our sales department at or sales@controlledautomation.com

16 Controlled Automation specializes in the manufacture of automated structural steel drilling, punching, and shape cutting machinery. We also build material handling systems to complement each type of machine we offer. As well as new machinery, we are the industry leader in retrofitting control systems and remanufacturing existing structural steel fabricating machinery. All machines and controls are designed and manufactured entirely in the United States of America. All software is developed and supported in the United States of America. US Mail PO Box 888 Bryant, AR USA Fax Manufacturing facility West Sardis Road Bauxite, AR USA 2008 Controlled Automation, Inc. ABL

Carbide Circular Sawing Systems. P-70B Min. 5/8 Max Capacity P-100B Min. 3/4 Max. 4 Capacity P-150B Min. 2-3/4 Max.

Carbide Circular Sawing Systems. P-70B Min. 5/8 Max Capacity P-100B Min. 3/4 Max. 4 Capacity P-150B Min. 2-3/4 Max. Carbide Circular Sawing Systems P-70B Min. 5/8 Max. 2.75 Capacity P-100B Min. 3/4 Max. 4 Capacity P-150B Min. 2-3/4 Max. 6 Capacity Carbide Circular Saws Standard Features Include Servo Driven Automatic

More information

SMF & MACHINE TOOLS, INC

SMF & MACHINE TOOLS, INC SMF & MACHINE TOOLS, INC 800-643-5839 METAL WORKING EQUIPMENT Local 501-897-1110 Fax 501-897-1110 14824 Rockbridge Road Little Rock, AR 72206 www.smfmachinetools.com sales@smfmachinetools.com P II 0 IRONWORKER

More information

SMF & MACHINE TOOLS, INC

SMF & MACHINE TOOLS, INC SMF & MACHINE TOOLS, INC 800-643-5839 METAL WORKING EQUIPMENT Local 501-897-1110 Fax 501-897-1110 14824 Rockbridge Road Little Rock, AR 72206 www.smfmachinetools.com sales@smfmachinetools.com C. '..-...p

More information

PII140 IRONWORKER PII140

PII140 IRONWORKER PII140 14824 Rockbridge Road Little Rock, AR 72206 Toll Free 800-643-5839 Fax 501-897-4090 www.smfmachinetools.com sales@smfmachinetools.com IRONWORKER 6 1 5 4 2 STANDARD FEATURES 1. Mechanical Stripper Attachment

More information

14824 Rockbridge Road Little Rock, AR Toll Free Fax

14824 Rockbridge Road Little Rock, AR Toll Free Fax 14824 Rockbridge Road Little Rock, AR 72206 Toll Free 800-643-5839 Fax 501-897-4090 www.smfmachinetools.com sales@smfmachinetools.com IRONWORKER STANDARD FEATURES 1. Urethane Stripper Attachment keeps

More information

IRONWORKERS MSIW50S MSIW66S MSIW60D MSIW71D MSIW93D

IRONWORKERS MSIW50S MSIW66S MSIW60D MSIW71D MSIW93D IRONWORKERS MSIW50S MSIW66S MSIW60D MSIW71D MSIW93D MSIW126D MSIW126DX MSIW192DX MSIW126D R SINGLE AND DUAL CYLINDER MACHINES 50-192 TON CAPACITY 5 STATIONS HEAVY DUTY CONSTRUCTION COMPLETELY INTEGRATED

More information

CSNC CARBIDE CIRCULAR SERIES

CSNC CARBIDE CIRCULAR SERIES CSNC CARBIDE CIRCULAR SERIES HIGHLY EFFICIENT AND PRODUCTIVE HIGH SPEED CIRCULAR SAWING MACHINES CARBIDE SAWS DO THE WORK OF FIVE CONVENTIONAL FACTORY BAND SAWS, WITHOUT SACRIFICING QUALITY. GET THE CLOSE-CUT

More information

METAL SHEAR SPECIALISTS MS-25-5 HYDRAULIC GUILLOTINE SHEAR

METAL SHEAR SPECIALISTS MS-25-5 HYDRAULIC GUILLOTINE SHEAR MS-25-5 HYDRAULIC GUILLOTE SHEAR MS-25-5 HYDRAULIC GUILLOTE SHEAR STANDARD Low speed electric motor & low hydraulic working pressure ensures long life. If the remote foot-pedal control is released anywhere

More information

Coil Handling and Press Feeding Equipment YESTERDAY S INTEGRITY. TOMORROW S TECHNOLOGY.

Coil Handling and Press Feeding Equipment YESTERDAY S INTEGRITY. TOMORROW S TECHNOLOGY. Coil Handling and Press Feeding Equipment YESTERDAY S INTEGRITY. TOMORROW S TECHNOLOGY. CORPORATE OVERVIEW Founded in 1966, CHS Automation has become the industry leader in coil handling equipment. Technology

More information

5 Maintenance 5.1 Guideway and Wipers

5 Maintenance 5.1 Guideway and Wipers 5 Maintenance 5.1 Guideway and Wipers 5.1 Page 26 of 41 The grinding carriage runs with hardened rollers on hardened steel straps (2). The steel straps (2) are positioned on the grinding bed (1) and tensioned

More information

18000 HDL FOUR POST LIFT LB CAPACITY INSTALLATION AND OWNER'S MANUAL

18000 HDL FOUR POST LIFT LB CAPACITY INSTALLATION AND OWNER'S MANUAL 18000 HDL FOUR POST LIFT 18000 LB CAPACITY INSTALLATION AND OWNER'S MANUAL WARNING! Do not raise a vehicle unless the front stops are in place, the parking brake is set, and the wheels are chocked. Stay

More information

MODEL # WTB-HRA/3. Hydraulic Wrap Around Bender Operating and Parts Manual. Manufactured by:

MODEL # WTB-HRA/3. Hydraulic Wrap Around Bender Operating and Parts Manual. Manufactured by: Hydraulic Wrap Around Bender Operating and Parts Manual MODEL # WTB-HRA/3 Manufactured by: Triangle Engineering Inc. Hanover, MA U.S.A. U.S. Patent 3,906,784 Tel# 781-878-1500 Fax# 781-878-2547 Rev 11/04

More information

Lockformer / 16 Gauge Speednotch

Lockformer / 16 Gauge Speednotch Lockformer / 16 Gauge Speednotch INSTALLATION PRELIMINARY: After uncrating, locate unit, with or without base skid, to area of operation. Unbind foot switch cord and cylinder hoses and remove gauge pin

More information

MS HYDRAULIC GUILLOTINE SHEAR

MS HYDRAULIC GUILLOTINE SHEAR MS-25-10 HYDRAULIC GUILLOTE SHEAR MS-25-10 HYDRAULIC GUILLOTE SHEAR STANDARD Low speed electric motor & low hydraulic working pressure ensures long life. If the remote foot-pedal control is released anywhere

More information

Hydraulic Clamp Carrier. Installation & Operation Manual

Hydraulic Clamp Carrier. Installation & Operation Manual Hydraulic Clamp Carrier Installation & Operation Manual Hydraulic Clamp Carrier Installation & Operation Manual Quick Machinery Company 8272 Peninsula Drive Kelseyville, CA 95451 phone: (707) 272-6719

More information

METAL BENDER OPERATING & MAINTENANCE INSTRUCTIONS Model Nos: CCB1 & CCB2 Part Nos: & CCB2 CCB1

METAL BENDER OPERATING & MAINTENANCE INSTRUCTIONS Model Nos: CCB1 & CCB2 Part Nos: & CCB2 CCB1 METAL BENDER Model Nos: CCB1 & CCB2 Part Nos: 7630073 & 7630074 CCB2 CCB1 OPERATING & MAINTENANCE INSTRUCTIONS 1206 1 The Compact Bender allows you to economically make a variety of bends in flat, square,

More information

CNC SYSTEMS PUNCHING SHEARING MARKING. Trilogy Machinery, Inc.

CNC SYSTEMS PUNCHING SHEARING MARKING.  Trilogy Machinery, Inc. The CNC Systems from SUNRISE are plate, angle and channel positioning systems with user-friendly interfaces. Many options are available factory-installed on Dual-Cylinder Ironworker or Punching Machines

More information

WELDING POSITIONING EQUIPMENT

WELDING POSITIONING EQUIPMENT WELDING POSITIONING EQUIPMENT It s difficult to compete in today s world with yesterday s technology. We have solutions. JMTUSA.com Email: JMT@JMTUSA.com Toll Free: 855-773-7727 (855-PRESS-BRAKE) JMT designs

More information

A UNIQUE LOOK Series Shape & Sand Machines Rev. E. 93 Model 330 pictured

A UNIQUE LOOK Series Shape & Sand Machines Rev. E. 93 Model 330 pictured 4500 Series Shape & Sand Machines Rev. E 93 Model 330 pictured UNIQUE Shape & Sand Machine History Unique has been producing Shape and Sand Machines for over 20 years and confidently produce quality industrial

More information

INSTALLATION, OPERATION, LUBRICATION, AND MAINTENANCE OF NO. S B18 AND B24 SMOOTH ROLL CRUSHERS

INSTALLATION, OPERATION, LUBRICATION, AND MAINTENANCE OF NO. S B18 AND B24 SMOOTH ROLL CRUSHERS INSTALLATION, OPERATION, LUBRICATION, AND MAINTENANCE OF NO. S B18 AND B24 SMOOTH ROLL CRUSHERS I. INSTALLATION A. RIGID MOUNTING: Use two heavy WF or I-beams running parallel underneath at least eight

More information

Rugged Powerful Durable

Rugged Powerful Durable Professional Grade Wood Splitters Rugged Powerful Durable Made in the USA UP TO 48 Mighty Profitable Splitters IDEAL FOR LANDSCAPE MAINTENANCE AND RENTAL Mighty Ox splitters are compact, powerful and

More information

SPECIFICATIONS MS-10-5 MS Cutting capacity (Rated 80,000 PSI Tensile) Cutting length 62 in "

SPECIFICATIONS MS-10-5 MS Cutting capacity (Rated 80,000 PSI Tensile) Cutting length 62 in MS-25-10 STANDARD Low speed electric motor & low hydraulic working pressure ensures long life. If the remote foot-pedal control is released anywhere in the stroke the ram returns to "up" position. Two

More information

CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS

CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS 20017 04/22/03 REV-A CUT OUT FLARES INSTALLATION INSTRUCTIONS FOR 20017, 20018, F100-F150 F250-F350 P.U. & BRONCO CUT OUTS Tools Required for Installation: (A) 3/16 Drill Bit (B) Pop-Rivet Gun (C) Air

More information

Industrial Solutions & Innovation, LLC. Watts Specialties

Industrial Solutions & Innovation, LLC. Watts Specialties Watts Specialties Improving Your Pipe Capabilities For Over 30 Years www.watts-specialties.com 24 & 36 Computerized Cutter Specifications W-242 W-244 W-362 W-364 Number of computer drive axis Number of

More information

MC-40 CNC PUNCH. Efficient, Quality Bus Bar Production

MC-40 CNC PUNCH. Efficient, Quality Bus Bar Production Jin FangYuan CNC Machine Company., Ltd (JFY) is one of the premier fabrications machine tool builders in Asia. Annually, they produce over,000 CNC fabricating machine tools. M & E Values, Inc. is proud

More information

IW SERIES IRONWORKERS DURMA

IW SERIES IRONWORKERS DURMA IW SERIES IRONWORKERS BETTER PARTS BETTER PROFITS IW SERIES IRONWORKERS STANDARD EQUIPMENT Swing Away Stripper Punching Station Section Cutting Angle Cutting Flat Bar Shearing Notching Twist and Drop Punch

More information

FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS

FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP SINGLE & DOUBLE UNDERBODY TRAILERS INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Trailer system.

More information

WELDING POSITIONING EQUIPMENT. JMT offers quality machine tools for all your sheet metal fabrication needs.

WELDING POSITIONING EQUIPMENT. JMT offers quality machine tools for all your sheet metal fabrication needs. WELDING POSITIONING EQUIPMENT JMT offers quality machine tools for all your sheet metal fabrication needs. JMTUSA.com Email: JMT@JMTUSA.com Toll Free: 855-773-7727 (855-PRESS-BRAKE) JMT sells and services

More information

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS

N. 15th Street, Middlesboro, KY FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS 1-800-248-7717 1002 N. 15th Street, Middlesboro, KY 40965 FLIP TARP DUMP BODY INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Mountain Flip Tarp Dump Body tarping system. With tarping systems

More information

(?'7 7 FARREL. Bulletin 1218-B ROLL-TURNING LATHES FARREL COMPANY, DIVISION OF USM CORPORATION, ROCHESTER, N.Y.

(?'7 7 FARREL. Bulletin 1218-B ROLL-TURNING LATHES FARREL COMPANY, DIVISION OF USM CORPORATION, ROCHESTER, N.Y. (?'7 7 FARREL Bulletin 11-B ROLL-TURNING LATHES FARREL COMPANY, DIVISION OF USM CORPORATION, ROCHESTER, N.Y. r Tracercontrolled lathe Installation view of 6 " lathe, shown turning a 51 % " x 10" blooming

More information

PORTABLE PULLER 55 Ton Capacity

PORTABLE PULLER 55 Ton Capacity SPX Corporation 5885 11th Street Rockford, IL 61109-3699 USA Internet Address: http://www.powerteam.com Tech. Services: (800) 477-8326 Fax: (800) 765-8326 Order Entry: (800) 541-1418 Fax: (800) 288-7031

More information

NORTH AMERICA ONLY GENERAL INFORMATION SCRAP SHEDDING ON DIES

NORTH AMERICA ONLY GENERAL INFORMATION SCRAP SHEDDING ON DIES GENERAL INFORMATION SCRAP SHEDDING ON DIES 1. CAST S FOR NOISE REDUCTION SEE W-DX5-58M PAGE 5. ALL S, ARE TO BE DESIGNED WITH A PREFERRED SHEDDING ANGLE OF 30 DEGREES, REACHING TO THE EDGE OF THE DIE.

More information

This just may be the Rotary Transfer machine you ve been waiting for.

This just may be the Rotary Transfer machine you ve been waiting for. This just may be the Rotary Transfer machine you ve been waiting for. A Machine Like No Other T he new Eclipse 12-100 is a ground-up redesign of the famous Hydromat concept with all new components. It

More information

Quality Built for High Performance

Quality Built for High Performance Quality Built for High Performance Split-Fire wood splitters offer quality workmanship and design that requires much less power to split wood while offering greater operator safety. Ton-for-ton, Split-Fire

More information

for impressive performances HYDRAULIC STEELWORKER Compact 50, 65, 80

for impressive performances HYDRAULIC STEELWORKER Compact 50, 65, 80 for impressive performances HYDRAULIC STEELWORKER Compact 50, 65, 80 HYDRAULIC STEELWORKERS COMPACT 50, 65, 80 The Compact 50, 65 and 80 are universal and compact hydraulic steelworkers. They are equipped

More information

How to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced)

How to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced) How to program the digital speed display (This is factory set and will only need to be programmed if the unit is replaced) 1. Press and hold the set button (top left corner) until the display shows Fun

More information

HIGH THROUGHPUT MINIMUM SET-UP TIME BT-Z LARGE BAR PEELERS

HIGH THROUGHPUT MINIMUM SET-UP TIME BT-Z LARGE BAR PEELERS UPDATE ON HETRAN BT-Z LARGE BAR PEELERS: MAXIMIZING PRODUCTIVITY IRRESPECTIVE OF ALLOY, BAR OR TUBE DIAMETER! Copyright September 2013 All Rights Reserved REVOLUTIONARY WORLD-CLASS DESIGN EXTENSIVE RANGE

More information

ATTENTION. 4. Do not over tighten the hydraulic fittings. This will cause leakage and will not be covered under warranty.

ATTENTION. 4. Do not over tighten the hydraulic fittings. This will cause leakage and will not be covered under warranty. NT-9 Installation Manual ATTENTION 1. Lubricate all four corners of both columns. A good clean grease works the best. You must check this every 90 days. Good lubrication is vital to the long term keep

More information

Compact Hydraulic System for Energy Savings and High Precision. POWER Meister

Compact Hydraulic System for Energy Savings and High Precision. POWER Meister Compact Hydraulic System for Energy Savings and High Precision POWER Meister POWER Meister Compact Hydraulic System Superior Energy Savings High Precision AC servo motor controls rotational speed and direction

More information

installation guide

installation guide JANUS INTERNATIONAL 1 866 562 2580 w w w. j a n u s i n t l. c o m 2000 2500 3000 installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 2000 2500 3000

More information

Heavy Equipment Solutions

Heavy Equipment Solutions Heavy Equipment Solutions Because ensuring a leak-free solution is critical. It has to be Hydratight. For more than 100 years, Hydratight has provided world-class bolted joint solutions, assessing and

More information

SHARP STA, STB, STC, STF SERIES CNC big bore flat bed lathe

SHARP STA, STB, STC, STF SERIES CNC big bore flat bed lathe SHARP STA, STB, STC, STF SERIES PRECISION MACHINE TOOLS Sharp Industries, Inc. 3501 Challenger Street Torrance, CA 90503 Tel 310-370-5990 Fax 310-542-6162 Email: info@sharp-industries.com Parts: parts@sharp-industries.com

More information

Segmented Transfer Plate Installation Instructions

Segmented Transfer Plate Installation Instructions Segmented Transfer Plate Installation Instructions Parts Included in Transfer Plate Kit: Transfer Plate Support Bar (1) Center Segment Right End Segment (1) Left End Segment (1) Mounting Bracket Assemblies

More information

OPERATIONS MANUAL. Featuring:

OPERATIONS MANUAL. Featuring: OPERATIONS MANUAL Used for commercial, architectural and industrial sheet metal fabrication Featuring: Pro Brake System Pro Accessories Setting up your Pro Brake Using your Pro Brake Snap Stand Set up

More information

HD installation guide

HD installation guide JANUS INTERNATIONAL 1 866 562 2580 www.janusintl.c o m 1950 1950HD installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 1950 1950HD SHOWN A rolling

More information

Sheet Metal Brake Plans for a 6' Sheet Metal Brake

Sheet Metal Brake Plans for a 6' Sheet Metal Brake Sheet Metal Brake Plans for a 6' Sheet Metal Brake,1752'8&7,21 Thank you for purchasing the sheet metal brake plans. The plans include a complete list of material needed and easy to follow steps to build

More information

Wire EDMing One-Piece Stamping Dies

Wire EDMing One-Piece Stamping Dies 8 121 Wire EDMing One-Piece Stamping Dies Blanking Die Wire EDM has made it possible to produce high quality dies from one piece of tool steel. This method of producing dies with wire EDM can result in

More information

Vipros 357 User Pre-installation Guide

Vipros 357 User Pre-installation Guide Amada America Inc. Vipros 357 User Pre-installation Guide Amada America Inc. 7025 Firestone Blvd. Buena Park CA. 90621 Phone: (714) 739 2111 Fax.: (714) 739 4099 Email infoamada.com Print Date 04/02/99

More information

KKS Circular Sawing Machines

KKS Circular Sawing Machines If Steel is Your Deal! KKS Circular Sawing www.kaltenbach.com 1 The complete KALTENBACH program for metal processing 2 www.kaltenbach.com 3 The Economical One Applications: locksmith s shop, metal construction,

More information

PIPE MASTER PIPE FACING, BEVELING, THREADING MACHINES PRESS BRAKES

PIPE MASTER PIPE FACING, BEVELING, THREADING MACHINES PRESS BRAKES PIPE MASTER PIPE FACING, BEVELING, THREADING MACHINES PRESS BRAKES ABOUT RMT Colton KALMAR / Service Technician Some of the Revolution Machine Tools Team RMT offers several innovative machines including

More information

Trade of Sheet Metalwork. Module 7: Introduction to CNC Sheet Metal Manufacturing Unit 2: CNC Machines Phase 2

Trade of Sheet Metalwork. Module 7: Introduction to CNC Sheet Metal Manufacturing Unit 2: CNC Machines Phase 2 Trade of Sheet Metalwork Module 7: Introduction to CNC Sheet Metal Manufacturing Unit 2: CNC Machines Phase 2 Table of Contents List of Figures... 4 List of Tables... 5 Document Release History... 6 Module

More information

XXL-Center. Cutting. Bending. Forming. R E I N H A R D T MASCHINENBAU D SINDELFINGEN D SINDELFINGEN RICHARD-WAGNER-STR.

XXL-Center. Cutting. Bending. Forming. R E I N H A R D T MASCHINENBAU D SINDELFINGEN D SINDELFINGEN RICHARD-WAGNER-STR. Cutting. Bending. Forming. XXL-Center D-71045 SINDELFINGEN P O S T F A C H 3 6 9 T E L E F O N 0 7 0 3 1-8 6 3-0 D-71065 SINDELFINGEN RICHARD-WAGNER-STR. 4 10 T E L E F A X 0 70 31-863-185 R E I N H A

More information

Inspection. Assembly Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent.

Inspection. Assembly Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent. 6010-34 Inspection 3. Install the springs. 1. Discard the 0-rings. 2. Clean all parts in cleaning solvent. 3. If spring test equipment is available, check the tension of each spring according to the specifications

More information

Rorty No.2 Tube Bender.

Rorty No.2 Tube Bender. Copyright. This entire Manual is copyrighted to Rorty Design, with all rights reserved. No part may be transferred or copied by any means whatsoever, without the express written permission of Rorty Design.

More information

PAN AND BOX BRAKE INSTRUCTIONS. Item #20649

PAN AND BOX BRAKE INSTRUCTIONS. Item #20649 PAN AND BOX BRAKE INSTRUCTIONS Item #20649 The EASTWOOD 12 & 24 PAN AND BOX BRAKES are precision engineered metal working tools designed to produce accurate, variable length bends in angles up to 135 in

More information

PRO Series Brakes Operating Instructions

PRO Series Brakes Operating Instructions PRO Series Brakes Operating Instructions Tapco Products Company PRO Brake System PRO Cut Off Gauge Simplifies cutting. PRO Cut-Off Quickly, safely, and easily makes factory quality cuts in coil stock,

More information

Operating, Servicing, and Safety Manual Model # & 72 Ultimate Box & Pan Brake

Operating, Servicing, and Safety Manual Model # & 72 Ultimate Box & Pan Brake Operating, Servicing, and Safety Manual Model # 2800 48 & 72 Ultimate Box & Pan Brake CAUTION: Read and Understand These Operating, Servicing, and Safety Instructions, Before Using This Machine. 1-800-467-2464

More information

STYLE BAR & TONNEAU COVER INSTALLATION

STYLE BAR & TONNEAU COVER INSTALLATION STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT

More information

SPACER APPLICATION: KEY POİNTS FOR HİGH QUALİTY İG UNİTS

SPACER APPLICATION: KEY POİNTS FOR HİGH QUALİTY İG UNİTS SPACER APPLICATION: KEY POİNTS FOR HİGH QUALİTY İG UNİTS Application of spacer should be in clean and indoor area. Glass washing machine, hot press machine and spacer application table should be in the

More information

Pneumatic Clamp Carrier. Installation & Operation Manual

Pneumatic Clamp Carrier. Installation & Operation Manual Pneumatic Clamp Carrier Installation & Operation Manual Pneumatic Clamp Carrier Installation & Operation Manual Quick Machinery Company 8272 Peninsula Drive Kelseyville, CA 95451 phone: (707) 272-6719

More information

Insolroll Clutch Operated Shades Installation Instructions Installation Instructions

Insolroll Clutch Operated Shades Installation Instructions Installation Instructions All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.

More information

400 Series. General Purpose Saws

400 Series. General Purpose Saws 400 Series General Purpose Saws OVERVIEW The 400 Series general purpose band saws are part of DoALL s introductory machines in the NEW StructurALL family of saws. The 400 Series are the ideal machines

More information

Providing Tools To Form Your Success

Providing Tools To Form Your Success If it's important to you, it's important to us. Find out how our attention to details forms the basis for your success. Providing ools o able of Contents For more than 30 years, leading sheet metal fabricators

More information

MODEL 83 Pail Handler

MODEL 83 Pail Handler MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE

More information

PowerLock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

PowerLock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 1944 FOR Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis,

More information

ELECTRIC RACER BASIC BUILD

ELECTRIC RACER BASIC BUILD Page 1 Name: Set: Date: This guide will take you through the process of creating a basic electric racer. After you finish this build, you should be able to experiment, design and engineer your own racer.

More information

Model PM Series Three Axis Mills

Model PM Series Three Axis Mills Model PM Series Three Axis Mills PM3000 PM2000 Features Setup & Operation Technical Data CLIMAX Portable Machine Tools, Inc. 10/98 1 Features Climax's PM Series 3-axis portable milling machines provide

More information

PRO Brake Operating Instructions

PRO Brake Operating Instructions PRO Brake Operating Instructions Tapco Products Company P R O 9 a n d P R O B r a k e s PRO Brake System PRO Cut Off Gauge Simplifies cutting. PRO Cut-Off Quickly, safely, and easily makes factory quality

More information

Section Content. Power Turntable Manual Turntable Low Profile Manual Turntable Optional Equipment and Devices

Section Content. Power Turntable Manual Turntable Low Profile Manual Turntable Optional Equipment and Devices s Section Content Power Manual Low Profile Manual Optional Equipment and Devices P.O. Box 352 Alpena, Michigan 49707 Phone 989.358.7000 Fax 989.358.7020 info@omni.com www.omni.com 105 TT s WHY TT? Provide

More information

SAFETY AND OPERATING MANUAL. Portable versatile workstation

SAFETY AND OPERATING MANUAL. Portable versatile workstation SAFETY AND OPERATING MANUAL Original instructions Portable versatile workstation wu063 1 2 3 4 5 6 7 8 9 Safety instructions Warning! When using this product basic safety precautions should always be followed.

More information

Circular Cold Saws and Systems for every application. Competence in Circular Cold Sawing Technology

Circular Cold Saws and Systems for every application. Competence in Circular Cold Sawing Technology Circular Cold Saws and Systems for every application Competence in Circular Cold Sawing Technology 2 VMS-Range Vertical Circular Cold Saws Manual, semi-automatic and automatic machines Robust and durable.

More information

Pega 345 Queen with Fanuc 04PC User Pre-installation Guide

Pega 345 Queen with Fanuc 04PC User Pre-installation Guide Pega 345 Queen with Fanuc 04PC User Pre-installation Guide Amada America Inc. 7025 Firestone Blvd. Buena Park CA. 90621 Phone: (714) 739 2111 Fax.: (714) 739 4099 Email info@amada.com Print Date 02/28/2001

More information

METAL TECHNOLOGIES A GENERATION AHEAD

METAL TECHNOLOGIES A GENERATION AHEAD METAL TECHNOLOGIES A GENERATION AHEAD THE LASER REVOLUTION Laser cutting has matured from a high-tech manufacturing process to a considerable common and popular manufacturing process today. Richinn Technology

More information

A Reference Guide. Continuous Hinge, Inventory and Service Worldwide Est End Play Design Engineering with Standard Continuous Hinges

A Reference Guide. Continuous Hinge, Inventory and Service Worldwide Est End Play Design Engineering with Standard Continuous Hinges Hinge Width Paint Clearance Knuckle Length End Play Design Engineering with Standard Continuous Hinges A Reference Guide Knuckle Dear Design Engineer or Purchasing Agent, We frequently see blueprints for

More information

Pneumatic Clamp Carrier. Installation & Operation Manual

Pneumatic Clamp Carrier. Installation & Operation Manual Pneumatic Clamp Carrier Installation & Operation Manual Pneumatic Clamp Carrier Installation & Operation Manual Quick Machinery Company 8272 Peninsula Drive Kelseyville, CA 95451 phone: (707) 272-6719

More information

M-Shear. Superior cutting technology with hybrid drive

M-Shear. Superior cutting technology with hybrid drive Superior cutting technology with hybrid drive De The E-volutie E-volution in plaatbewerking sheet metal working The E-volution in sheet metal working increases your competitive strength as a manufacturer

More information

NUMBERALL STAMP & TOOL CO., INC. USER MANUAL & PARTS LIST S/N: P.O. BOX 187, 1 HIGH ST. SANGERVILLE, ME TEL: FAX:

NUMBERALL STAMP & TOOL CO., INC. USER MANUAL & PARTS LIST S/N: P.O. BOX 187, 1 HIGH ST. SANGERVILLE, ME TEL: FAX: NUMBERALL STAMP & TOOL CO., INC. USER MANUAL & PARTS LIST MODEL 301 S/N: P.O. BOX 187, 1 HIGH ST. SANGERVILLE, ME 04479 www.numberall.com office@numberall.com TEL: 207-876-3541 FAX: 207-876-3566 MODEL

More information

FORM 2. THE PATENTS ACT, 1970 (39 of 1970) & THE PATENTS RULES, 2003

FORM 2. THE PATENTS ACT, 1970 (39 of 1970) & THE PATENTS RULES, 2003 FORM 2 THE PATENTS ACT, 1970 (39 of 1970) & THE PATENTS RULES, 03 COMPLETE SPECIFICATION (See section, rule 13) 1. Title of the invention: BANDING MACHINE 2. Applicant(s) NAME NATIONALITY ADDRESS ITC LIMITED

More information

4" METAL BENDER INSTRUCTIONS. Part #20521

4 METAL BENDER INSTRUCTIONS. Part #20521 4" METAL BENDER INSTRUCTIONS Part #20521 The EASTWOOD 4 METAL BENDER is a high quality, industrial style tool capable of generating a powerful 2-1/2 tons of pressing force to create 90 or lesser repeatable

More information

VERTICAL FORM FILL SEAL MACHINES

VERTICAL FORM FILL SEAL MACHINES VERTICAL FORM FILL SEAL MACHINES AUTOMATIC PACKAGING MACHINES 49 Vertical Form, Fill Seal Machines: With over 30 years experience, Audion manufactures a complete line of reliable, flexible, low maintenance,

More information

SWITCH STAND Switch Stand Assembly Connecting Rod Target Assembly (when required) TURNOUT ACCESSORIES Standard Tie Plates Rail Anchors Joints

SWITCH STAND Switch Stand Assembly Connecting Rod Target Assembly (when required) TURNOUT ACCESSORIES Standard Tie Plates Rail Anchors Joints Turnouts A turnout is an arrangement of a switch, a frog and closure rails, which diverts rolling stock from one track to another. Because industrial trackwork often handles lighter loads at slower speeds

More information

Model 20: Home & Garden Cart

Model 20: Home & Garden Cart Model 20: Home & Garden Cart Parts List Step 1: A: Install two ¾ Bolts (C) through the rear trim piece on the Bottom Panel (S) and attach to Lock Nuts. (Lock nuts on bottom side) B: Place left Side Panel

More information

Policy Sponsor: Assistant Vice President Facilities Management. Responsible Unit: Trade Services

Policy Sponsor: Assistant Vice President Facilities Management. Responsible Unit: Trade Services Safe Work Instructions for Powered Mitre Cut Hack Saw (Mitercut Model 220M) Policy Sponsor: Assistant Vice President Facilities Management Responsible Unit: Trade Services Approval Date: November 2016

More information

Global Expansion of Human Activity and The Wave of Motorization

Global Expansion of Human Activity and The Wave of Motorization About Fine Blanking Global Expansion of Human Activity and The Wave of Motorization Enhancing the productivity of international automobile manufacturers In the attractive international automobile manufacturing

More information

That s E[M]CONOMY: Big Performance for small Parts. EMCO MAXXTURN 25. Universal turning center for the complete machining of small, precision parts

That s E[M]CONOMY: Big Performance for small Parts. EMCO MAXXTURN 25. Universal turning center for the complete machining of small, precision parts [ That s ] E[M]CONOMY: Big Performance for small Parts. EMCO MAXXTURN 25 Universal turning center for the complete machining of small, precision parts EMCO MAXXTURN 25 [Work area] - Spacious - Free chip

More information

METALMASTER HG-3216VR. Hydraulic NC Guillotine - Variable Rake x 16mm Mild Steel Shearing Capacity. Product Brochure

METALMASTER HG-3216VR. Hydraulic NC Guillotine - Variable Rake x 16mm Mild Steel Shearing Capacity. Product Brochure Product Brochure S9615 METALMASTER HG-3216VR Hydraulic NC Guillotine - Variable Rake 3200 x 16mm Mild Steel Shearing Capacity Page 1 of 5 Right View Front View Side View Rear Guarding 3 Safety Electronic

More information

THE LOG SPLITTER YOU WILL ENJOY USING.

THE LOG SPLITTER YOU WILL ENJOY USING. BY CENTRAL BOILER THE LOG SPLITTER YOU WILL ENJOY USING. STRYKER log splitters offer quality workmanship second to none. Because of their unique design and manufactured finish, they require much less power

More information

Pega 357 with Fanuc 04PC User Pre-installation Guide

Pega 357 with Fanuc 04PC User Pre-installation Guide Pega 357 with Fanuc 04PC User Pre-installation Guide Amada America Inc. 7025 Firestone Blvd. Buena Park CA. 90621 Phone: (714) 739 2111 Fax.: (714) 739 4099 Email info@amada.com Print Date 03/02/2001 Revision

More information

Stripping & Blanking Supplies

Stripping & Blanking Supplies Stripping & Blanking Supplies Stripping Pins Stripping Pins - available in the sizes and styles shown above. 50 mm tall (2 ). All base sizes are the same (4mm) for consistent drilling and laser cutting

More information

The ultimate affordability in valve seat machining

The ultimate affordability in valve seat machining The ultimate affordability in valve seat machining SG7 cylinder head seat & guide machine Light Weight Work Head The SG7 has a light weight work head for extremely fast and accurate centering for the ultimate

More information

SHHP20 FLOOR STANDING HYDRAULIC PRESS

SHHP20 FLOOR STANDING HYDRAULIC PRESS SHHP20 FLOOR STANDING HYDRAULIC PRESS OWNER S MANUAL 20 TON MAX CAPACITY FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE. SPECIFICATION MAX CAPACITY STROKE WORK

More information

PowerLock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.

PowerLock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered. Serving the Truck & Trailer Industry Since 1944 PowerLock Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis,

More information

Form No Assembly & Operating Instructions for: SAFETY PRECAUTIONS

Form No Assembly & Operating Instructions for: SAFETY PRECAUTIONS Form No. 0230 Assembly & Operating Instructions for: 833 20300 83 2220 837 0-0008 078 SHOP PRESS Max. Capacity: 2 Ton These instructions are intended for various shop presses. Some models are shipped assembled

More information

Pega 367 with Fanuc 04PC User Pre-installation Guide

Pega 367 with Fanuc 04PC User Pre-installation Guide Pega 367 with Fanuc 04PC User Pre-installation Guide Amada America Inc. 7025 Firestone Blvd. Buena Park CA. 90621 Phone: (714) 739 2111 Fax.: (714) 739 4099 Email info@amada.com Print Date 03/07/2001 Revision

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Thank you for purchasing a Shelti product. All of us at Shelti want you to be completely satisfied with your Coin Pool Table, so feel free to contact us for help with the assembly

More information

AL NASR ENGINEERING (AL QUSAIS FACILITY)

AL NASR ENGINEERING (AL QUSAIS FACILITY) AL NASR ENGINEERING (AL QUSAIS FACILITY) CNC MACHINE SHOP, SPECIAL PURPOSE MACHINE MANUFACTURING, RETROFITTING, AVIATION EQUIPMENTS, ROBOTICS AND AUTOMATION TABLE OF CONTENTS INDUSTRIAL LICENSE COMMERCIAL

More information

Heavy Duty Pipe Wrench

Heavy Duty Pipe Wrench Heavy Duty Pipe Wrench High-tensile ductile iron handle and hardened tool-steel parts. Designed to withstand heavy demands. Easy-spin adjusting nut is heat-treated for durability. Drop-forged jaw is heat-treated

More information

CONTENTS PRECAUTIONS BEFORE STARTING OPERATION PREPARATION FOR OPERATION CAUTIONS ON USE OPERATION

CONTENTS PRECAUTIONS BEFORE STARTING OPERATION PREPARATION FOR OPERATION CAUTIONS ON USE OPERATION CONTENTS PRECAUTIONS BEFORE STARTING OPERATION ------------------------------------- 1 PREPARATION FOR OPERATION 1. Adjustment of needle bar stop position ---------------------------------------------------------

More information

Martin Yale 7000E Guillotine Cutter

Martin Yale 7000E Guillotine Cutter Martin Yale 7000E Guillotine Cutter Blade Leveling Guide Provided By http://www.mybinding.com http://www.mybindingblog.com Blade Removal, Installation and Leveling for the 7000E Disclaimer The following

More information

Celebrating. 65 Years

Celebrating. 65 Years Celebrating 65 Years Contents Beveling Equipment Clamps - Internal Clamps - External Auxiliary Equipment Pipe Lifting Welding Qualification Pipe Bending Beveling Equipment On Band Type Beveling Machine:

More information