PROCEDURE:INSTALLATION OF BOLTED AND THREADED CONNECTIONS. as a result of improper lifting technique.

Size: px
Start display at page:

Download "PROCEDURE:INSTALLATION OF BOLTED AND THREADED CONNECTIONS. as a result of improper lifting technique."

Transcription

1 RISK RANKING: LOW HAZARD ASSESSMENT: HAZARD 1. Improper use of tools or using faulty tools. 2. Physical strain. POTENTIAL EFFECTS 1. Worker could suffer personal injury if not using tools properly. 2. Back or muscle strain as a result of improper lifting technique. CONTROL 1. Use proper PPE and follow procedures on use of tools. 2. Use lifting equipment or use buddy system for two man lifts. SAFETY EQUIPMENT: Safety Glasses with side shields, hard hat, steel toe boots, FR Clothing, gloves, personal gas monitor and torque wrench. SAFETY NOTE: Hydrocarbon products are very susceptible to leaking through improperly fastened joints. Personnel shall adhere to the following instructions to determine all connections are properly fastened and free of leaks. These instructions are intended for all replacement work as well as new additions or constructions. PROCEDURE: 1. Flanges: all flanges shall be inspected for imperfections and damage such as lateral scores and dents across the gramophone finish. If any flanges are found to be damaged; they must be replaced, especially during new construction or additions. 2. Gaskets: shall be inspected for flattened area, tears, breaks and other imperfections that could cause leaking joints. Any gasket found damaged shall be rejected and a replacement provided. 3. Bolts, studs and nuts: Those require replacing or for any additions or new construction shall be as per the grade stipulated on drawings. All bolt and stud threads shall be inspected for imperfections such as flattened threads, broken threads, cross threads, etc. Nuts shall be similarly checked for thread damage. Ensure that the nuts run down the bolt or stud freely; replace any damaged or unfit pieces. 1 Date of Preparation: November 23, 2004

2 4. Lubricants: applied to the bolt or stud threads, nut threads and nut faces shall be of the proper and correct type. For NGL piping systems the recommended lubricant is Jet-Lube Nikal or equivalent. 5. Threaded fittings, nipples and valves: shall have all threads inspected for imperfections and damage such as scoring, flats, broken or cross threading, etc. Reject or replace all damaged fittings. Apply one wrap of Teflon tape to all male ends of any threaded connections (Loctite Teflon Thread Sealant #59231 or #59241 or equivalent is recommended). This is followed by applying SWAK or equivalent thread dope on top on the wrap of Teflon tape to the leading threads of the fittings prior to fastening the item in its intended location. Where certain valves are supplied with stainless steel bodies and threads, take due care and attention to ensure that threads or any adjoining carbon steel threaded connections are not damaged or scored by the stainless steel threads. The stainless steel connection does not require as much torque applied to make a tight leak free connection as the equivalent carbon steel threaded connection. 6. Assembly of flanged connections shall use the following sequence to make a tight leak free joint:. Ensure all flanges, gaskets, bolts, studs and nuts are free of dirt, mud, grit, etc.. Bring flanges together ensuring there is sufficient gap to install the gasket. Flanges shall be aligned so that there is not any hi-low between the mating flange faces.. Ensure that the bolts, studs and nuts have been lubricated.. Install two or three bolts near the bottom of the flange to receive and cradle the gasket.. Install gasket between the flanges.. Install remainder of the bolts and studs.. Tighten all nuts to finger tightness. Center the studs between the nuts so that an equal number of threads extend past the nut on each side of the connection.. Tighten bolts or studs starting first at the 12 o clock position, 6 o clock position, 3 o clock position, 9 o clock position. Then alternating out, remember when you tighten one bolt or stud you then must tighten the one directly across from it. Tighten bolts or studs in the 12, 6, 3 and 9 o clock positions using 25% of required torque. Tighten the remaining bolts or studs in sequence to 50% of required torque. Tighten all bolts or studs in sequence to 75% of required torque. Tighten all bolts or studs in sequence to 100% of required torque. Note: If the flanges are difficult to align and it becomes necessary to use the bolts or studs to bring the flanges together, all bolts or studs and nuts shall be replaced with new ones after the initial bolt-up has been made. Follow the same steps as previously detailed in this procedure to fasten the connection the second time. The following shows recommended bolt-up specifications and bolt or stud loadings. 7. Torque and Stretch Specifications for Flanged Joints Requirement: 40% ofyield unless otherwise specified. 2 Date of Preparation: November 23, 2004

3 Stud/bolt material L psi yield strength. To achieve correct torque, lubrication of studs/bolts, nuts must be done as per specifications. If nuts/bolts are inspected and lubricated, flanges and gaskets inspected and torque is re-checked for relaxation after 24 hours, leaking joints should be eliminated. Lubrication must be stressed as a most important phase of assembly. Non-lubricated joints can affect torque by as much as 50%. Stretch readings need only be used to verify torque calculations. Torque tolerance of plus 10% can be used on all joints. 150 lb. Flanges 8. Size Bolts Size Stretch Torque ft/lbs ¾ ½ / ½ 1/ / / / Lb. Flanges Size Bolts Size Stretch Torque ft/lbs 1/2 5/ /4 5/ / / / / / / Date of Preparation: November 23, 2004

4 / / ¼ ¼ ¼ / lb. Flanges Size Bolts Size Stretch Torqueft/Ibs ¾ 5/ / /2 3/ / / / ¼ ¼ / / / / Date of Preparation: November 23, 2004

5 24 1 7/ Date of Preparation: November 23, 2004

NTTC Tank Truck Week Awareness Gaskets/Fasteners/Flanges

NTTC Tank Truck Week Awareness Gaskets/Fasteners/Flanges NTTC Tank Truck Week 2015 Awareness Gaskets/Fasteners/Flanges OVERVIEW 1. Flange 101 Flange Types Inspection & Assembly 2. Gaskets 101 Stress Tightness 3. Fastener 101 Yield Lubrication Bolted Flanged

More information

Practical Bolting and Gasketing for the Non Standard-Flanged Joint

Practical Bolting and Gasketing for the Non Standard-Flanged Joint Practical Bolting and Gasketing for the Non Standard-Flanged Joint Points of Discussion Introduction Joint Analysis Existing Flange Data Machining Procedure Bolting Radial Shear Available Gasket Styles

More information

MECH-100: Fundamentals of Precision Maintenance

MECH-100: Fundamentals of Precision Maintenance MECH-100: Fundamentals of Precision Maintenance Universal Technologies, Inc. Student Guide Page 1 Torquing Topic Goals... 3 Introduction... 4 JOINT PRELOAD... 4 BOLT PRELOAD... 6 PRELOAD SEQUENCING...

More information

I-W07/W77. Couplings DETAIL A WARNING. Photo Showing Pipe with Weld Seam Ground 6 inches/152 mm Back from Pipe End and an AGS Groove

I-W07/W77. Couplings DETAIL A WARNING. Photo Showing Pipe with Weld Seam Ground 6 inches/152 mm Back from Pipe End and an AGS Groove WARNING Read and understand all instructions before attempting to install any Victaulic piping products. These products must be used only on pipe that is prepared to Victaulic Advanced Groove System (AGS)

More information

Reliance SG800 Series Steel Water Gage Valves

Reliance SG800 Series Steel Water Gage Valves Installation, Operation, & Maintenance Instructions R500.541D1 10/16/2016 Reliance SG800 Series Steel Water Gage Valves Note: Design variations in Steel Water Gage Valves necessitate typical illustrations,

More information

Assmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS

Assmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS Assmann Corporation of America TANK INSTALLATION AND USE GUIDELINES FOR BULK STORAGE TANKS General Information Assmann polyethylene storage tanks are manufactured to give you the toughest, most reliable

More information

Joint Preparation prior to Tensioning: General:

Joint Preparation prior to Tensioning: General: `Hydraulic Tensioner Procedure for 50% tensioning: Document: PWL-HTS-101 Joint Preparation prior to Tensioning: General: Clean Flanges and check for scars on the flange surface area Check studs and nuts

More information

GUIDELINES FOR HINGED AND BOLTED MANWAY ASSEMBLY

GUIDELINES FOR HINGED AND BOLTED MANWAY ASSEMBLY GUIDELINES FOR HINGED AND BOLTED MANWAY ASSEMBLY Assembly Instructions for the Flammable Liquid Industry Published by: Renewable Fuels Association Authored by: Watco Compliance Services, VSP Technologies,

More information

Typical Group D Rear Acoustical Cover Installation

Typical Group D Rear Acoustical Cover Installation SERIES 60 SERVICE MANUAL 1. Gear Case Cover 5. Bolt 2. Gear Case 6. Acoustical Cover 3. Acoustical Cover Snap 7. Acoustical Cover 4. Acoustical Cover Clip 8. Nut Figure 1-179 Typical Group D Rear Acoustical

More information

Figure 11 Flange Adapter and Back-Up Ring

Figure 11 Flange Adapter and Back-Up Ring Flange Adapters Standard back-up rings are Standard back-up rings are convoluted ductile iron with AWWA C207 150 lb drilling. One edge of the back-up ring bore must be radiused or chamfered. This edge

More information

SYGEF Standard SYGEF Plus PVDF Flanges

SYGEF Standard SYGEF Plus PVDF Flanges Installation Instructions 2009 Volume, Rev 02 PM451 SYGEF Standard SYGEF Plus PVDF Flanges Please read all instructions before attempting to install flanges. Introduction When to Use a Flange Flanges may

More information

Reliance SG777 Series Steel Water Gage Valves

Reliance SG777 Series Steel Water Gage Valves Installation, Operation, & Maintenance Instructions R500.SG777 10/16/2016 Reliance SG777 Series Steel Water Gage Valves Note: Design variations in Steel Water Gage Valves necessitate typical illustrations,

More information

Fluid Sealing Association

Fluid Sealing Association Fluid Sealing Association STANDARD FSA-MG-501-02 STANDARD TEST METHOD FOR INWARD BUCKLING OF SPIRAL-WOUND GASKETS 994 Old Eagle School Road, Suite 1019 Wayne, Pennsylvania 19087-1866 Phone: (610) 971-4850

More information

Understanding pipe threads: types and designations

Understanding pipe threads: types and designations WHITE PAPER 8008 Understanding pipe threads: types and designations By Mark Schmidt Applications Engineer CPC (Colder Products Company) Different types of screw threads have evolved for fastening and hydraulic

More information

Auto-Spreader Spreader HS10K Hydraulic Flange Spreader

Auto-Spreader Spreader HS10K Hydraulic Flange Spreader Auto-Spreader Spreader HS10K Hydraulic Flange Spreader US Patent No. 5678293 Operation and Maintenance Manual Keep For Your Records Contents Operation...2 Maximum Spreader Extension...3 Safety Tips...4

More information

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back HSF 250 Patriot Heavy Duty Line Stop Fitting - 4, 6, 8 inch Nominal Sizes Line Stop Fitting Installation Instructions Push and Pin Completion Plug Installation Instructions IMPORTANT: Read installation

More information

MALEKO WALL-MOUNT FAUCET INSTALLATION

MALEKO WALL-MOUNT FAUCET INSTALLATION SKU(s): 934146 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the

More information

Installation Instructions TMW Antenna Tower Mount for 4ft (1.2m) Antennas.

Installation Instructions TMW Antenna Tower Mount for 4ft (1.2m) Antennas. Description The following pages show the steps required to assembly and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation

More information

AF-4 Grooved Flange Adapter

AF-4 Grooved Flange Adapter SUBMITTAL INFORMATION PROJECT NAME: ENGINEER: CONTRACTOR: SPEC. SECTION: MEMBER FEATURES & ADVANTAGES Designed for connecting ANSI/AWWA C110/A21.10 and ASME/ANSI B16.1 Class 125/ flanged end components

More information

HEATEC TEC-NOTE Publication No

HEATEC TEC-NOTE Publication No HEATEC TEC-NOTE Publication No. 6-04-126 How to prevent leaks in pipe joints at HMA plants This document is intended as a guide for installing pipe joints on Heatec products at HMA (hot mix asphalt) plants.

More information

INSTALLATION MANUAL FOR STAINLESS STEEL, GROOVE-END, FLEXIBLE COUPLINGS

INSTALLATION MANUAL FOR STAINLESS STEEL, GROOVE-END, FLEXIBLE COUPLINGS PIEDMONT PACIFIC CORPORATION INSTALLATION MANUAL FOR STAINLESS STEEL, GROOVE-END, FLEXIBLE COUPLINGS 4703 Tidewater Ave., Suite G Oakland. CA, 94601, USA Ph: +1 510 434 0990 / Fax: +1 510 436 0990 www.piedmontpacific.com

More information

w w w. h d o n l i n e s h o p. d e AUTOMATIC COMPRESSION RELEASE TOOL GENERAL INSTALLATION -J04654 REV Kit Number Models

w w w. h d o n l i n e s h o p. d e AUTOMATIC COMPRESSION RELEASE TOOL GENERAL INSTALLATION -J04654 REV Kit Number Models -J05 REV. 008-0- GENERAL Kit Number 98-08 Models AUTOMATIC COMPRESSION RELEASE TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com

More information

9 METHOD COVERED FOR BOLT TORQUING & TENSIONING

9 METHOD COVERED FOR BOLT TORQUING & TENSIONING Sl. No. DESCRIPTION 1 PURPOSE 2 SCOPE 3 DEFINATION 4 REFERENCES 5 RESPONSABILITIES 6 OBJECTIVES 7 QUALIFIED TECHNICIANS 8 SAFETY 9 METHOD COVERED FOR BOLT TORQUING & TENSIONING 10 EQUIPMENT 11 CALIBRATION

More information

Axles Covered in This Bulletin. How to Obtain Additional Maintenance, Service and Product Information. Product Design Variations. How to Obtain Kits

Axles Covered in This Bulletin. How to Obtain Additional Maintenance, Service and Product Information. Product Design Variations. How to Obtain Kits Technical Bulletin Revised 09-7 Carrier-to-Housing Joint Reseal Procedure Service procedure to be used any time a carrier is removed and reinstalled. Includes tapered dowel installation information. All

More information

Assembly instructions for swivel mechanical joints Bondstrand fiberglass pipe series

Assembly instructions for swivel mechanical joints Bondstrand fiberglass pipe series Assembly instructions for swivel mechanical joints Bondstrand fiberglass pipe series Scope These instructions describe the proper procedures for the installation of Bondstrand Swivel mechanical joints.

More information

Structural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the grade A325 structural bolt.

Structural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the grade A325 structural bolt. Structural Bolting ASTM F3125/F3125M is a structural bolt specification covering inch and metric bolt grades. This specification contains 4 inch series bolting grades: A325, F1852, A490, and F2280. These

More information

ANTENNA EXPERTS. Website: AP MHz. 2.4 Meters 30dBi. Gain

ANTENNA EXPERTS.   Website:   AP MHz. 2.4 Meters 30dBi. Gain ANTENNA EXPERTS E-mail: info@antennaexperts.in Website: www.antennaexperts.in AP-180030 1700 1900 MHz. 2.4 Meters 30dBi. Gain INSTALLATION MANUAL GRID PARABOLIC ANTENNA NOTICE: Installation, maintenance

More information

I-350. FIELD INSTALLATION HANDBOOK Victaulic Piping Products for CPVC/PVC Materials PRODUCT INSTALLATION INSTALLATION INSPECTION HELPFUL INFORMATION

I-350. FIELD INSTALLATION HANDBOOK Victaulic Piping Products for CPVC/PVC Materials PRODUCT INSTALLATION INSTALLATION INSPECTION HELPFUL INFORMATION I-350 FIELD INSTALLATION HANDBOOK Victaulic Piping Products for CPVC/PVC Materials PRODUCT INSTALLATION INSTALLATION INSPECTION HELPFUL INFORMATION WARNING Read and understand all instructions before attempting

More information

BALANTINE WALL-MOUNT FAUCET INSTALLATION

BALANTINE WALL-MOUNT FAUCET INSTALLATION SKU(s): 911574, 911575 BALANTINE WALL-MOUNT FAUCET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware

More information

www.wildmanconstruction.com Changing your toilet is an easy project that should take half a day or less. The most common toilet has a separate tank that mounts on top of the bowl. These instructions apply

More information

Installation, Operation, Inspection and Maintenance Manual

Installation, Operation, Inspection and Maintenance Manual Installation, Operation, Inspection and Maintenance Manual System: KTM 1 Table of Contents 1.0 Introduction... 2 1.1 Precautions... 2 1.2 Regulations... 2 1.3 Technical Specifications... 2 1.4 Required

More information

I-VICFLEX.VS1. Victaulic VicFlex Style VS1 Dry Sprinkler WARNING WARNING TECHNICAL DATA BEND CHARACTERISTICS INSTALLATION INSTRUCTIONS SIDEWALL

I-VICFLEX.VS1. Victaulic VicFlex Style VS1 Dry Sprinkler WARNING WARNING TECHNICAL DATA BEND CHARACTERISTICS INSTALLATION INSTRUCTIONS SIDEWALL INSTALLATION INSTRUCTIONS I-VICFLEX.VS1 Victaulic VicFlex Style VS1 Dry Sprinkler SIDEWALL Y Read and understand all instructions before attempting to install any Victaulic VicFlex Style VS1 Dry Sprinklers.

More information

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extension Sections. Reliable Connections

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extension Sections. Reliable Connections insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extension 2-3 Improved Fire Hydrant Inserting Extension

More information

25000 Series Lo-T TM Butterfly Control Valve Instructions

25000 Series Lo-T TM Butterfly Control Valve Instructions November 2001 25000 Series Lo-T TM Butterfly Control Valve Instructions Instruction No. 25.1:IM PRELIMINARY STEPS Before installation, note the flow direction arrow on the valve body. The flow should enter

More information

INSTRUCTIONS INSTRUCCIONES CONSIGNES

INSTRUCTIONS INSTRUCCIONES CONSIGNES AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2007-2010 CHEVY/GMC SILVERADO/SIERRA 2500/3500 (EXCLUDES CLASSIC) APP PART #46-23715, 40-92315/45-92310 MAX WINCH TRAY, SPORTSMAN

More information

Hydraulic Adapters STEEL PIPE ADAPTERS NPTF DRY SEAL PIPE ASSEMBLY INSTRUCTIONS. Steel Pipe Adapters. Steel Pipe Adapters. Hydraulic.

Hydraulic Adapters STEEL PIPE ADAPTERS NPTF DRY SEAL PIPE ASSEMBLY INSTRUCTIONS. Steel Pipe Adapters. Steel Pipe Adapters. Hydraulic. CONFORMANCE SAE J54 for hex nipples, expanders, elbows, tees and crosses SAE J54, J50 and J5 for bushing and plugs. Temperature Range -65 0 F to +400 0 F MATERIALS - SAE L4 carbon steel plated zinc with

More information

HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT

HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT Introduction SECTION 1 Thank you for purchasing one of our fine True Focus products. This manual covers the

More information

Durapipe ABS Jointing Guide

Durapipe ABS Jointing Guide Durapipe ABS Jointing Guide Solvent cement welding offers a simple and quick means of constructing high integrity, leak-free joints. The solvent cement operates by chemically softening the joint surfaces.

More information

Pipe Restrainers series C Restrainers for use on IPEX Bionax AWWA CI OD C909 PVCO Pipe with MJ or Push-On Fittings

Pipe Restrainers series C Restrainers for use on IPEX Bionax AWWA CI OD C909 PVCO Pipe with MJ or Push-On Fittings Pipe Restrainers series 1000 1000C Restrainers for use on IPEX Bionax AWWA CI OD C909 PVCO Pipe with MJ or Push-On Fittings INFORMATION Restrainers for restraining mechanical joint or push-on fittings

More information

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16 R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged

More information

TURBOTWISTER TM ASSEMBLY AND INSTALLATION INSTRUCTIONS

TURBOTWISTER TM ASSEMBLY AND INSTALLATION INSTRUCTIONS TURBOTWISTER TM ASSEMBLY AND INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 Phone: (503) 266-2231 Fax: (503)

More information

TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS

TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 Phone: (503) 266-2231 Fax: (503) 266-4334

More information

SIGHT GLASS. Sight glass components allow operators to safely observe processes inside tanks, pipes, reactors and vessels.

SIGHT GLASS. Sight glass components allow operators to safely observe processes inside tanks, pipes, reactors and vessels. SIGHT GLASS Sight glass components allow operators to safely observe processes inside tanks, pipes, reactors and vessels. SIGHT GLASS Sight flow indicator. A sight flow indicator is used in process pipelines

More information

BIPPMM03 (Published) Book specs- Dates: / / Lang: ENG01 Applic: PPM

BIPPMM03 (Published) Book specs- Dates: / / Lang: ENG01 Applic: PPM BIPPMM03 (Published) Book specs- Dates: 20060412 / 20060412 / 20060412 Lang: ENG01 Applic: PPM Installing the Milnor Diaphragm in the Single Stage Press This document applies to models MP160Axx, MP1604xx,

More information

10. Do not install within 10 feet of a pool, spa, or fountain. 4. Keep lamp away from materials that may burn.

10. Do not install within 10 feet of a pool, spa, or fountain. 4. Keep lamp away from materials that may burn. 1. Do not touch fixture while lamp is on. Turn off/unplug and allow to cool before replacing lamp. 9. Remove any debris or build-up accumulated on the faceplate or lens periodically. Replace lens if necessary.

More information

TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS

TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS TURBOTWISTER ASSEMBLY AND INSTALLATION INSTRUCTIONS CORPORATE HEADQUARTERS WESTERN SALES AND MANUFACTURING PLANT P.O. Box 400 1017 SW Berg Parkway Canby, Oregon 97013 Phone: (503) 266-2231 Fax: (503) 266-4334

More information

SERVICE INSTRUCTION. 652 Oliver Street Williamsport, PA U.S.A. Tel Fax

SERVICE INSTRUCTION. 652 Oliver Street Williamsport, PA U.S.A. Tel Fax 652 Oliver Street Williamsport, PA. 17701 U.S.A. Tel. 570 323 6181 Fax. 570 327 7101 www.lycoming.com SERVICE INSTRUCTION DATE: March 6, 2012 Service Instruction No. 1458F (Supersedes Service Instruction

More information

4/29/2016 Big Block Main Bearing Stud Girdle Kit HUG7380K For B & RB Blocks

4/29/2016 Big Block Main Bearing Stud Girdle Kit HUG7380K For B & RB Blocks Big Block Main Bearing Stud Girdle Kit HUG7380K For B & RB Blocks Contents of Kit 2-4.40 Main Studs 8-5.187 Main Studs 1- Girdle Plate 18- ½ ARP black flat washers 8- ½-20 Grade 8 plain hex nuts 8- ½-20

More information

Instruction Sheet RADIO FREQUENCY SYSTEMS. Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) No Rev.

Instruction Sheet RADIO FREQUENCY SYSTEMS. Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) No Rev. Instruction Sheet No. 412764 Rev. B ECO 12469 Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) These Installation Instructions are valid for antennas in the following version: reflector 2.4

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,

More information

Acrylic Claw Foot Tub

Acrylic Claw Foot Tub Acrylic Claw Foot Tub Wrench or socket Drill & Bits Parts Recommended 2-2 x12 boards 4 Lag Bolts 4 Flat Washers Be sure to re-inforce the floor before securing tub. We recommend 2-2 x12 s securely fastened

More information

USER MANUAL Nord-Lock X-series washers

USER MANUAL Nord-Lock X-series washers USER MANUAL Nord-Lock X-series washers JOINT GUIDE 3 ASSEMBLY INSTRUCTIONS 4 TECHNICAL DATA 5 TORQUE GUIDE 5 THE EXCEPTIONAL SYSTEM THAT PREVENTS BOLT LOOSENING AND SLACKENING Nord-Lock X-series washers

More information

COMMON WRENCHES INTRODUCTION

COMMON WRENCHES INTRODUCTION COMMON WRENCHES INTRODUCTION A wrench is a hand tool used to provide grip and mechanical advantage in applying torque to turn objects usually nuts and bolts. Wrenches allow us to use less force to rotate

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION

More information

OAK GROVE PLANT MAINTENANCE SECTION-MECHANICAL

OAK GROVE PLANT MAINTENANCE SECTION-MECHANICAL UNIT 1 PULVERIZER SYSTEM SEMI-ANNUAL INSPECTION OG-MSM-229 EFFECTIVE DATE: PREPARED BY (Print): TOM PERSON 8/31/21 EXT: 6395 TECHNICAL REVIEW BY (Print): EXT: APPROVED BY: DATE: OG-MSM-229 PAGE 2 OF 24

More information

Operating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher

Operating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher Operating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher Model # 100 Standard Model #100-U Heavy Duty CAUTION: Read and Understand

More information

This specification describes the minimum requirements for piping systems for the following service:

This specification describes the minimum requirements for piping systems for the following service: 201/11/2 1/9 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Underground Service Water Note: This specification does not apply to piping

More information

Tidland Series 950/960 Slitter Shaft

Tidland Series 950/960 Slitter Shaft TIDLAND SLITTING SOLUTIONS Tidland Series 950/960 Slitter Shaft Installation, Operation and Maintenance EN Series 950 GK Series 960 GR MI 666264 1 H IMPORTANT SAFETY INSTRUCTIONS When using this Tidland

More information

NAVSEA STANDARD ITEM

NAVSEA STANDARD ITEM NAVSEA STANDARD ITEM FY-19 DATE: 01 OCT 2017 CATEGORY: I 1. SCOPE: 1.1 Title: Threaded Fastener Requirements; accomplish 2. REFERENCES: 2.1 Standard Items 2.2 S9086-CJ-STM-010/075, Fasteners 3. REQUIREMENTS:

More information

- INSTALLATION INSTRUCTIONS -

- INSTALLATION INSTRUCTIONS - . Supercharger Shaft Upgrade Kit PART# - RY17040-UK-6S5-2 APPLICATION(S): Yamaha FX-SHO, FZR & FZS Required tools Part# IN LB Electronic Torque Wrench N/A T-30 Torx Bit Socket N/A 3mm Allen Wrench N/A

More information

May 14, Installation Manual

May 14, Installation Manual May 14, 2012 Installation Manual Contents MAG TRACKER Components...1 Mount Installation...7 Module Installation & Grounding...11 Maintenance...14 Warranty......14 Contact Information......14 May 14, 2012

More information

MODEL H " BYRD SHELIX CUTTERHEAD INSTRUCTIONS

MODEL H  BYRD SHELIX CUTTERHEAD INSTRUCTIONS MODEL H9291 12" BYRD SHELIX CUTTERHEAD INSTRUCTIONS The Model H9291 12" Byrd Shelix cutterhead is designed to replace the straight-knife cutterhead on the Grizzly jointer Model G0609. The total procedure

More information

Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe

Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe Stargrip series 3000 Mechanical Joint Wedge Action Restraint for Ductile Iron Pipe INFORMATION The Stargrip Mechanical Joint Restraint System is a unique product with a proven design that provides an exceptional

More information

Fasteners. Fastener. Chapter 18

Fasteners. Fastener. Chapter 18 Fasteners Chapter 18 Material taken from Mott, 2003, Machine Elements in Mechanical Design Fastener A fastener is any device used to connect or join two or more components. The most common are threaded

More information

The DeltaGrip System. Safety and Operating Instructions. Trigger. Air Supply Connection. Handle Assembly. Air Line Assembly.

The DeltaGrip System. Safety and Operating Instructions. Trigger. Air Supply Connection. Handle Assembly. Air Line Assembly. The DeltaGrip System Safety and Operating Instructions Trigger Air Supply Connection Handle Assembly Air Line Assembly Punch Die Pneumatic Diaphragm Assembly Shackle, Pin & Jam Nut Jaw Frame Shoulder Screw

More information

Austin Standing Seam Awning Assembly and Installation Instructions. Assembly Instructions

Austin Standing Seam Awning Assembly and Installation Instructions. Assembly Instructions Austin Standing Seam Awning Assembly and Installation Instructions Be sure to use safety glasses when assembling and installing the awning. Some metal parts may have sharp edges. Use work gloves to handle

More information

Type XTSR71 Sizes

Type XTSR71 Sizes (Page 1 of 13) s 494-5258 Type XTSR71 s 494-5258 Figure 1 Thomas XTSR71 Coupling 1. General Information 1.1 Thomas Couplings are designed to provide a mechanical connection between the rotating shafts

More information

LATTIMORE SHOWER SET INSTALLATION

LATTIMORE SHOWER SET INSTALLATION SKU(s): 931419 LATTIMORE SHOWER SET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability

More information

Chiltern Model Steam Engines

Chiltern Model Steam Engines Chiltern Model Steam Engines Mill Twin Cylinder Model Steam Engine v2 Assembly Instructions v1.0 Notes: 1. In overview the engine should first be assembled "dry" with no oil/lubricants, thread lock or

More information

Installation, Operation & Maintenance Manual

Installation, Operation & Maintenance Manual Original Instructions Installation, Operation & Maintenance Manual Saf-T-Vise STV-HP1 Insertable Tool Holders S-CM-IOM-00506-0 4-17 Do not install, maintain, or operate this equipment without reading,

More information

Procedure for Wrench Calibration and Snug Tightening

Procedure for Wrench Calibration and Snug Tightening Procedure for Wrench Calibration and Snug Tightening 1. Scope: This procedure provides the method for calibration of a manual torque wrench or an adjustable impact wrench and the snug tightening procedure

More information

Evaluation of In-Pavement Light Fixture Designs and Performance

Evaluation of In-Pavement Light Fixture Designs and Performance Evaluation of In-Pavement Light Fixture Designs and Performance Presented to: IES ALC Fall Technology Meeting By: Joseph Breen Date: Background In-Pavement Light Fixture Assemblies Utilize a Circle of

More information

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16 Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete

More information

ROTUNDA WALL-MOUNT FAUCET INSTALLATION

ROTUNDA WALL-MOUNT FAUCET INSTALLATION SKU(s): 919045 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the

More information

SCION FR-S REAR SPOILER Preparation

SCION FR-S REAR SPOILER Preparation Preparation Part Number: PT938-18130-XX Kit Contents Item # Quantity Reqd. Description 1 1 Spoiler 2 2 Strut 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 M6 x 1 Nut with

More information

INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE

INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE The material included in this kit is to be used for WC styles of brakes that are designed or upgraded to the EP

More information

TYPE 3740XL EXTRA LARGE WET RUNNING CARTRIDGE SPLIT SEAL

TYPE 3740XL EXTRA LARGE WET RUNNING CARTRIDGE SPLIT SEAL 1 Foreword These instructions are provided to familiarize the user with the seal and its designated use. The instructions must be read and applied whenever work is done on the seal, and must be kept available

More information

TECHNICAL INSTRUCTIONS

TECHNICAL INSTRUCTIONS 0 TECHNICAL INSTRUCTIONS Innovation Anode Retrofit Instructions This kit applies to all Innovation model water heaters ITEM 1: P/N 44173 ANODE MOUNTING BRACKET ITEM 2: P/N 44174 ANODE BLOCK (2 each) ITEM

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PROTRAXX OVAL STEP BAR APPLICATION: 2009-2017 Dodge Ram 1500 Crew/Quad Cab 2010-2017 Dodge Ram 2500/500 Crew Cab PART NUMBER: 21-550, 21-555, 21-50, 21-55 AUTOMOTIVE PRODUCTS,

More information

General Practices & Preventative Maintenance for your Pellet Mill

General Practices & Preventative Maintenance for your Pellet Mill General Practices & Preventative Maintenance for your Pellet Mill The pellet feed industry has grown to cover a wide range of animal feeds. Studies have shown that feeding animals pelleted feed will induce

More information

RATCHET CABLE CUTTER

RATCHET CABLE CUTTER OPERATION, SERVICE AND PARTS INSTRUCTION MANUAL 764 RATCHET CABLE CUTTER Read and understand this material before operating or servicing this equipment. Failure to understand how to safely operate this

More information

INSTRUCTION MANUAL IM 251 For Gas Turbine Tensioned Studs and Nuts VENDOR SUPPLIED

INSTRUCTION MANUAL IM 251 For Gas Turbine Tensioned Studs and Nuts VENDOR SUPPLIED INSTRUCTION MANUAL IM 251 For Gas Turbine Tensioned Studs and Nuts Note: This manual is written specifically for connections that employ the use of Load Coupling Spacers placed under the nuts. If spacers

More information

INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: ,

INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: , INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: 2010-2014 CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: 32-21020, 32-21025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 CONTOUR BAR TORQUE WRENCH 2 1

More information

4" METAL BENDER INSTRUCTIONS. Part #20521

4 METAL BENDER INSTRUCTIONS. Part #20521 4" METAL BENDER INSTRUCTIONS Part #20521 The EASTWOOD 4 METAL BENDER is a high quality, industrial style tool capable of generating a powerful 2-1/2 tons of pressing force to create 90 or lesser repeatable

More information

Assembly Instructions

Assembly Instructions page 1 Serious personal-injury to the operator or bystanders, as well as damage to equipment or property, can occur, if all safety and assembly instructions, provided with this product, are not followed.

More information

MAHLE CBP-10 / CBP-10A & CSP-10 / CSP-10A. Operation Manual Shop press

MAHLE CBP-10 / CBP-10A & CSP-10 / CSP-10A. Operation Manual Shop press MAHLE CBP-10 / CBP-10A & CSP-10 / CSP-10A EN Operation Manual Shop press en 2 CBP-10 / CSP-10 EVERY PERSON WHO OPERATES THIS EQUIPMENT NEEDS TO KNOW AND UNDERSTAND ALL OF THE INFORMATION IN THIS MANUAL

More information

TYPE 3740/3740D WET/DRY RUNNING CARTRIDGE SPLIT SEAL

TYPE 3740/3740D WET/DRY RUNNING CARTRIDGE SPLIT SEAL 1 Foreword These instructions are provided to familiarize the user with the seal and its designated use. The instructions must be read and applied whenever work is done on the seal, and must be kept available

More information

CONTROLS KIT FOR ALL # & # HARLEY DAVIDSON SPORTSTER MODELS

CONTROLS KIT FOR ALL # & # HARLEY DAVIDSON SPORTSTER MODELS INSTALLATION INSTRUCTIONS TC BROS. CHOPPERS PART #0-0075 & #0-0076 (No Pegs) FORWARD CONTROLS KIT FOR ALL 00-0 HARLEY DAVIDSON SPORTSTER MODELS If downloading & printing these instructions online, be sure

More information

Riser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18. Manual 40100X35-8

Riser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18. Manual 40100X35-8 Riser Extension INSTALLATION GUIDE 40100AX35 / 40100AX18 Manual 40100X35-8 3 2 4 Access covers with bolts supplied with Interceptor 1 5 14 6 11 15 Sampling Port/Cleanout cap supplied with Interceptor 12

More information

GLENBROOK/GLENGUARD VITREOUS CHINA DRINKING FOUNTAIN/CUSPIDOR

GLENBROOK/GLENGUARD VITREOUS CHINA DRINKING FOUNTAIN/CUSPIDOR GLENBROOK/GLENGUARD VITREOUS CHINA DRINKING FOUNTAIN/CUSPIDOR BEFORE YOU BEGIN HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials,

More information

This specification describes the minimum requirements for piping systems for the following service:

This specification describes the minimum requirements for piping systems for the following service: SPEC-3004 1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Water Design Conditions Operating Conditions 10 PSIG @ 33 o F to

More information

CRITICAL INFORMATION:

CRITICAL INFORMATION: IMPORTANT ALERT: GM uses a very strong thread-locking compound on all body bolts. Use of an air assisted impact ratchet can cause damage to the threads on factory body mount bolts and the internal nut

More information

This specification describes the minimum requirements for piping systems for the following service:

This specification describes the minimum requirements for piping systems for the following service: SPEC-3501 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Instrument Air Design Conditions 150 PSIG @ 180 F Operating Conditions 125

More information

2. Install two guide studs, J 36107, to the gear case. See Figure

2. Install two guide studs, J 36107, to the gear case. See Figure SERIES 60 SERVICE MANUAL 2. Install two guide studs, J 36107, to the gear case. See Figure 1-174. 1. Front Gear Case Cover 4. Locating Dowel (Round) 2. Front Engine Lift Bracket 5. Locating Dowel (Diamond)

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

Mathey Dearman Single and Double Screw Chain Clamp Parts & Operating Manual

Mathey Dearman Single and Double Screw Chain Clamp Parts & Operating Manual Machine Model Serial# WHERE THERE S PIPE, THERE S MATHEY Mathey Dearman Single and Double Screw Chain Clamp Parts & Operating Manual Revised: 1/9/2018 P. O. Box 472110, Tulsa, OK 74147-2110 USA Toll Free:

More information

Submersible Turbine Assembly Manual

Submersible Turbine Assembly Manual Submersible Turbine Assembly Manual Table of Contents Submersible Turbine Kit Assembly Page Recommended Equipment... 2 Assembly Instructions...3-9 Special Tool Schematics... 10 Symbol Key Action Safety/Caution

More information

INSTRUCTION MANUAL IM 382 For Gas Turbine Tensioned Studs and Nuts CUSTOMER'S INFORMATION BOX CONTENTS ARE INDEPENDENT OF RIVERHAWK DOCUMENT CONTROL

INSTRUCTION MANUAL IM 382 For Gas Turbine Tensioned Studs and Nuts CUSTOMER'S INFORMATION BOX CONTENTS ARE INDEPENDENT OF RIVERHAWK DOCUMENT CONTROL INSTRUCTION MANUAL IM 382 For Gas Turbine Tensioned Studs and Nuts Applicable Bolting Connections Frame 9FA Gas Turbine to Load Coupling Load Coupling to 324 Generator Steam Turbine to 324 Generator Applicable

More information

Impact Wrench. 19 mm (3/4 ) MODEL 6906

Impact Wrench. 19 mm (3/4 ) MODEL 6906 Impact Wrench 9 mm (3/4 ) MODEL 6906 002290 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

More information

PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0

PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 DYNATRAC PRODUCTS 2003-2010 4X4 DODGE 2500/3500 HEAVY DUTY BALL JOINT PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 WARNING: Improper use or installation of this product can cause major failures that could

More information