Laser Trackers for Production of Automotive Tooling

Size: px
Start display at page:

Download "Laser Trackers for Production of Automotive Tooling"

Transcription

1 Case Study Laser Trackers for Production of Automotive Tooling PICO EUROPE designs, manufactures, installs and commissions automotive production lines worldwide for many automotive manufacturers including Ford, Jaguar, Scania, Volvo and many others. PICO EUROPE has been using Leica Laser Trackers in assembly line production since 1996 and now has a total of five Leica Laser Tracker systems. The object of this case study is to give the reader an insight how a laser tracker is implemented for the production of automotive tooling. Also illustrated is how the laser tracker gives the user a greater understanding of the manufacturing process, enabling him to implement proactive improvements from design right through to assembly line final commissioning. Also included is an overview of PICO EUROPE s manufacturing process before the use of laser trackers; enabling the reader to draw a contrast between the measuring processes pre and post laser tracker introduction. Production Objective PICO EUROPE s production objective is to assemble every tool that makes up the production line by bringing together pre-machined tool bases, units, form blocks and location pins in the correct dimensional configuration to reflect the design of the car. This procedure is performed at the PICO EUROPE site. The complete assembly line is then tested. The next challenge is to transport the entire production line piece by piece to the customer s site and reproduce the dimensional configuration achieved at the PICO EUROPE site before final testing and commissioning can commence. Leica Laser Tracker A Laser Tracker is a portable coordinate measuring machine (CMM) for large volume measurements based on a laser interferometer, which tracks and measures the position of a target reflector to an accuracy of 10 microns per metre. The system can measure up to points a second and has a radial range of 35 metres. Measurement may be made statically to a tooling hole on automotive tooling, or, dynamically for digitising the surface of a door skin or press tool. Once measured these data can be analysed against discrete nominal X,Y & Z coordinates or free form CAD surfaces. PICO EUROPE

2 Production line The Global Standard Typically a tooling hole is measured using a precision-machined reflector holder that locates into the tooling hole. The reflector is then located into the reflector holder. The position of the hole is easily measured since the dimensional relationship between the hole, reflector holder and reflector are known. Two sizes of reflector are commonly used with 0.5 inch and 1.5 inch diameters. Procedure at PICO EUROPE before Laser Tracker Implementation On arrival at PICO EUROPE site, tool bases were transported to a fixed solid body CMM and inspected for flatness and the position of unit fixing and doweling locations. If the tool was too large for the CMM s measuring envelope the base was measured in 2 separate halves using the CMM. This process involved measuring one side of the base, then rotating it 180 degrees to measure the other side. The disadvantage of this method was that it was extremely difficult to link both sides of the tool together with any degree of relative accuracy. Smaller tools that fell within the measuring envelope of the CMM could be certified in their fully assembled state. Therefore all the units, form blocks and location pins were positioned on the tool base first, before the tool assembly was positioned on the flat bed of CMM for certification. Having been checked on the CMM the larger bases were transported to another location on the shop floor where the tool assembly began. Another pitfall of moving a large steel plate from one location to another was that its shape changed due to its own weight. Therefore before tool assembly could start the base was levelled again using an optical level. After the complete assembly of the tool with the relative units and form blocks etc; the tool was certified using conventional stick micrometers, steel straight edges and cubes. Employing these traditional methods often made it necessary to move a previously set unit to allow clearance for positioning a straight edge or block. As you can imagine this process took much time and manual effort; removing and replacing units and positioning heavy straight edges and cubes. This process was further compounded if the tool base happened to be at 45 degrees instead of level. Each separate tool assembly was then set up in its position to form part of the production line. Measuring tools used were a combination of piano wires for alignment, stick micrometers for tool spacing and optical levels for levelling the complete line. In moving the tools from the position they were certified to their position in the line, often meant that the tool flexed in some way and the dimensional integrity of the tool was compromised. Measuring the tool in the line proved even more difficult. The completed production line was then tested at the PICO EUROPE site before being transported to the customer s factory for installation and commissioning. Again, moving an entire assembly line from one factory to another poses even more problems in terms of the tools flexing. However, on the customer s site there was no reliable way of verifying or re-certifying the tools. If a unit was damaged in transport, replacing it on site was again difficult as the only way to certify the newly installed unit was to use conventional methods. At this stage removing units would be further hampered due to the installation of pneumatic piping and electric wiring systems. On many occasions a dispute would arise because the customer s panels didn t fit PICO EUROPE s tooling properly. A situation that was extremely difficult to resolve since there was no reliable method of measuring the tooling to verify its compliance to the customer s design. Needless to say much time and money was wasted. Current Laser Tracker Procedure Tool Build PICO EUROPE Site Pre-machined tool bases arrive including all necessary dowel and fixing holes. Datums are also included and can take different forms such as edges, grooves, or holes depending on the customer. These datums provide the initial means of measuring in car-line with the Leica Laser Tracker. If floor space permits the bases can be positioned directly into their relative position in the assembly line. Level datums are established at each end of the production line that the laser tracker is able to use to generate an extremely accurate gravity coordinate system. All the bases on the line can then be levelled co-planar to one another. Piano wires are sometimes still used to roughly align the bases, however final alignment and spacing is performed using a laser tracker since it has a radial range of 35 metres. The laser tracker is then used to check and adjust (via support jacking screws) the flatness of the tool base. Also verified are the position of the tool base s dowel and fixing holes. Tool assembly then commences: first units, then form blocks and location pins. Once complete the tool is ready to be certified. All the components PICO EUROPE

3 that go together to make up the tooling are pre-machined and their assembly configuration should be close to nominal. The Leica Laser Tracker is then used to measure the tool geometry. Shims are used to make final adjustments. Tool Certification The first step is to measure the datums located on the tool base. Since the position of these datums is known in car-line coordinate system the laser tracker operator is able to perform a coordinate system transformation allowing the laser tracker to measure in car-line coordinate system. The next exercise is to measure all the pass points on the tool in carline. These will now become the primary tool reference in preference to those located on the tool base. Approximately 20 pass points are spread evenly throughout the whole volume of the tool. Once the pass-points are measured each master dowel hole location and every location pin on each unit is measured and adjusted to meet the design specification. The following paragraphs expand on the methods used to measure master dowel holes and panel location pins. Measurements of Master Dowel Hole There are 2 dowel holes to locate each form block but only one is usually measured. A reflector holder along with a reflector is located into the dowel hole, its position is then measured revealing its coordinates in car-line. A simple comparison to the nominal position for this point reveals whether the hole is in the correct position or needs to be moved by adjusting shims. As well as the master dowel hole being in the correct position, the master dowel hole locating face needs to be at the correct attitude in terms of 3 rotations since this will be crucial to the orientation of the form block. This attribute is verified using a bolt on master form block known as a PICO block. Instead of having a free form surface on one side, the PICO block has a series of precisionmachined holes in all of its visible sides that will accommodate a reflector holder. By measuring 3 to 4 points on this block it is possible to determine the attitude of the master dowel hole locating face. Measurements of Location Pins Two methods are used to measure location pins. The first is to employ a 2-point method. A location pin may be perceived by its centre line axis. To define the location pin axis it is necessary to measure at least two points along it. This is easily achieved by having reflector holders at different height offsets. A simple analysis will show the attitude of the pin. Another method is to digitise the pin by moving the reflector over the surface, and performing a cylinder fit. The resulting cylinder axis will represent the pin axis. PICO EUROPE employ the former method for the majority of the time. Once all master dowel holes and panel location pins have been measured and adjusted within design tolerance a report is issued. The report contains actual dimensions, design dimensions and deviations. The pass-point coordinates are also included in the report, which are to become the primary tool references and are essential for the next assembly and recertification stage at the customer s site. Line Assembly Customer Site Once the whole assembly has been certified and tested at the PICO EUROPE site it is dismantled piece by piece and transported to the customer s factory for final assembly, verification and commissioning. Panel sitting on location pin On arrival each tool is positioned into its respective position in the assembly line. Level datums are established at each end of the production line that the laser tracker is able to generate an extremely accurate gravity coordinate system to which all bases are levelled. Piano wires are used to roughly align all the tools. Final alignment and spacing of the tools is performed using the Leica laser tracker. Tool Verification Once the tool has been levelled and is situated in its final position the first step is to measure all the passpoints, approximately 20, using the laser tracker. Pass-points are now the primary tool references. A bestfit coordinate transformation is then performed and its results scrutinised. These results tell the operator much about the dimensional integrity of the tool. Firstly the operator checks that the overall root mean square error (RMS) of the coordinate transformation solution does not exceed a predefined tolerance, usually 0.13 mm. If the RMS value falls within the specified tolerance the tool s dimensional integrity is considered sound enough to warrant only one verification. Verification involves checking all location pins and 10% of master dowel holes. If these fall within tolerance the tool is considered verified. If however the coordinate transformation RMS falls outside tolerance, and any spurious points have been checked and re-measured, a re-certification is performed. Re-certification is required because either damage or flexure has compromised the overall geometry of the tool. Re-Certification Re-certification, as its name suggests involves a repetition of the activities previously performed at the PICO EUROPE site, i.e. 100% inspection of all features and adjustment to within tolerance. All the tools that form the line undergo the process described above before the production line is ready for testing and final commissioning.

4 Automotive Tooling Glossary of Terms Tool Base Form Blocks Master Dowel Hole Pre machined rectangular steel plate that forms the foundation of the tool to which all other items are assembled. Also premachined are all necessary datums, dowel holes and fixing holes. Pass Point This is the pre-machined dowel location hole on the unit and corresponding form block. Panel location Pins These are small steel blocks with holes in them that are welded to the units. The holes provide locations for reflector holders and will be used later as primary tool datums. Machined steel blocks that locate onto the units via master dowels. The location interface between form block and unit is machined flat, both parts having pre machined dowel holes for location. One of the other sides of the form block represents the freeform CAD surface of the car and will support the actual car panel. The relationship of the form block s freeform surface and the dowel hole are known. Units Shims Individual steel support brackets that are located and bolted to the tool base. Units have their own unique number i.e. Unit 103. Small steel plates for location between form blocks and units to facilitate linear adjustment in X, Y or Z axes. Pins that locate individual panels on the tool, usually 2 per panel. Pins locate onto units.

5 Checking the Freeform Surface of Form Blocks to CAD Data Some automotive manufacturers place an additional requirement, which is to measure points on the form block s freeform surface and compare them to the CAD design surface of the car. Ultimately it is this surface that will position the panels of the car before spot welding. The measurement results are presented using graphical reports depicting the panel of the car and coloured needle vectors representing the point error direction and magnitude from the CAD surface. Needles are also labeled with point ID and numerical deviation. Software such as Leica s Axyz CAD and Interprog may be used to perform this analysis function. Ultimately the decision whether to use the position and attitude of the master dowel hole or to measure to the freeform surface of the form block lies with the customer. Leica Laser Tracker for Repetition and Reproducibility Measurement At times it is necessary to perform repeatability and reproducibility studies on tooling. A typical example is to locate and clamp a panel into its position on the tooling, then unclamp and remove the panel. The panel is then relocated and clamped for the second time. If the tooling is well designed and manufactured, the panel should locate back into the same position to within an acceptable margin. Repeatability and reproducibility are attributes that are obviously essential for mass production tooling. Laser trackers are used to a great extent for these types of measurements, which often run up to 30 relocation cycles. Up to 8 reflectors are temporarily bonded to the panel with a hot glue gun. The reflector positions are evenly spread over the panel surface. A laser tracker with an Absolute Distance Meter (ADM) is required for this measurement exercise i.e. the Leica LTD500. Each reflector is then measured with the laser tracker. The coordinates from the first measurement cycle become the reference coordinates for all other measurement cycles. The panel is unclamped and removed from the tooling, then repositioned and re-clamped for the second time. For the second and all subsequent cycles the auto-inspect software routine is employed. The auto-inspect function drives the laser beam to each reference coordinate position in-turn and then measures the actual new position of the reflector giving its deviations. With up to 30 measurement cycles of 8 points the auto-inspect function is extremely useful. The auto-inspect function enables many data to be collected in a short time, typically 30 minutes for an 8 reflector, 30 cycle R & R study. Conclusion As mentioned in the introduction, this paper is designed to give the reader an insight and a flavour of how PICO EUROPE uses Leica Laser Trackers for production of automotive tooling. There are always exceptions to the rule in engineering and automotive production tooling can take many different forms. Therefore not every piece of production tooling follows the procedures described. «Since its introduction at PICO EUROPE the laser tracker has revolutionised the way in which we build automotive production tooling. The dimensional integrity of the tooling can now be guaranteed from initial assembly and certification at PICO EUROPE right through to the customer site anywhere in the world. If problems do occur with tooling, like panel misalignments, the possibility now exists for us to examine and precisely pinpoint the cause of the problem and implement corrective action. The laser tracker plays a major role in enabling us at PICO EUROPE to manufacture tooling to comply with the ever-increasing accuracy requirements of the modern motor car.» PICO EUROPE

6 Leica Geosystems Leica Geosystems is a leading developer, manufacturer and distributor of products, systems and software that capture, visualize and process spatial data through the employment of advanced technologies. Leica Geosystems supplies solutions to the varied users of spatial data. In several of these fields we hold the leading position in the world market. Headquarters Leica Geosystems AG Metrology Division Moenchmattweg 5 CH-5035 Unterentfelden Switzerland Phone Fax info.metrology@leica-geosystems.com Metrology Division The Metrology Division offers 3D measurement solutions for any demand in industrial processes, setting new standards for procedures in every major industry. Using state-of-the-art laser technology, we have made quality control and construction of large objects or small parts easier than ever before and accurate down to a few microns giving our customers unique advantages and cost savings in every field. Visit us at metrology For an updated reference list and additional addresses, please refer to our web site.

AUTOMATION OF 3D MEASUREMENTS FOR THE FINAL ASSEMBLY STEPS OF THE LHC DIPOLE MAGNETS

AUTOMATION OF 3D MEASUREMENTS FOR THE FINAL ASSEMBLY STEPS OF THE LHC DIPOLE MAGNETS IWAA2004, CERN, Geneva, 4-7 October 2004 AUTOMATION OF 3D MEASUREMENTS FOR THE FINAL ASSEMBLY STEPS OF THE LHC DIPOLE MAGNETS M. Bajko, R. Chamizo, C. Charrondiere, A. Kuzmin 1, CERN, 1211 Geneva 23, Switzerland

More information

MEASURING MACHINES. Pratt & Whitney METROLOGY LABORATORY. Measurement Systems, Inc.

MEASURING MACHINES. Pratt & Whitney METROLOGY LABORATORY. Measurement Systems, Inc. METROLOGY LABORATORY Pratt & Whitney Measurement s, Inc. METROLOGY LABORATORY The Standard of Accuracy Pratt & Whitney Metrology Laboratory Machines are the standard to which all other gages are held subordinate.

More information

SURVEY AND ALIGNMENT FOR THE SWISS LIGHT SOURCE

SURVEY AND ALIGNMENT FOR THE SWISS LIGHT SOURCE 1 SURVEY AND ALIGNMENT FOR THE SWISS LIGHT SOURCE F.Q. Wei, K. Dreyer, U. Fehlmann, J.L. Pochon and A. Wrulich SLS / Paul Scherrer Institute CH5232 Villigen PSI Switzerland ABSTRACT The Swiss Light Source

More information

More Info at Open Access Database by S. Dutta and T. Schmidt

More Info at Open Access Database  by S. Dutta and T. Schmidt More Info at Open Access Database www.ndt.net/?id=17657 New concept for higher Robot position accuracy during thermography measurement to be implemented with the existing prototype automated thermography

More information

Module-4 Lecture-2 Perpendicularity measurement. (Refer Slide Time: 00:13)

Module-4 Lecture-2 Perpendicularity measurement. (Refer Slide Time: 00:13) Metrology Prof. Dr. Kanakuppi Sadashivappa Department of Industrial and Production Engineering Bapuji Institute of Engineering and Technology-Davangere Module-4 Lecture-2 Perpendicularity measurement (Refer

More information

Fast Optical Form Measurements of Rough Cylindrical and Conical Surfaces in Diesel Fuel Injection Components

Fast Optical Form Measurements of Rough Cylindrical and Conical Surfaces in Diesel Fuel Injection Components Fast Optical Form Measurements of Rough Cylindrical and Conical Surfaces in Diesel Fuel Injection Components Thomas J. Dunn, Robert Michaels, Simon Lee, Mark Tronolone, and Andrew Kulawiec; Corning Tropel

More information

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel INSTALLATION INSTRUCTIONS Frame Reinforcement Kit 11100 (Patent Pending) 1968-72 GM A-Body Coupe/Sedan Read Instructions FULLY before starting Installation Important Note Installation of this kit requires

More information

High Accuracy Spherical Near-Field Measurements On a Stationary Antenna

High Accuracy Spherical Near-Field Measurements On a Stationary Antenna High Accuracy Spherical Near-Field Measurements On a Stationary Antenna Greg Hindman, Hulean Tyler Nearfield Systems Inc. 19730 Magellan Drive Torrance, CA 90502 ABSTRACT Most conventional spherical near-field

More information

Mobrey Gauged Head Verification Device (HVD)

Mobrey Gauged Head Verification Device (HVD) Quick Installation Guide Mobrey HVD Mobrey Gauged Head Verification Device (HVD) Start The Mobrey HVD Step 1: Installation Step 2: Operating The HVD End www.emersonprocess.com Mobrey HVD Quick Installation

More information

GEOMETRICAL TOLERANCING

GEOMETRICAL TOLERANCING GEOMETRICAL TOLERANCING Introduction In a typical engineering design and production environment, the designer of a part rarely follows the design to the shop floor, and consequently the only means of communication

More information

PRODUCT BROCHURE HP-L-10.6 HP-L-20.8 LASER SCANNER FOR COORDINATE MEASURING MACHINES

PRODUCT BROCHURE HP-L-10.6 HP-L-20.8 LASER SCANNER FOR COORDINATE MEASURING MACHINES PRODUCT BROCHURE HP-L-10.6 HP-L-20.8 LASER SCANNER FOR COORDINATE MEASURING MACHINES HP-L LASER SCANNER FAST, PRECISE AND VERSATILE THANKS TO FLYING-DOT TECHNOLOGY HP-L laser scanners deliver maximum

More information

COURSE SYLLABUS. Course Title: Introduction to Quality and Continuous Improvement

COURSE SYLLABUS. Course Title: Introduction to Quality and Continuous Improvement COURSE SYLLABUS Course Number: TBD Course Title: Introduction to Quality and Continuous Improvement Course Pre-requisites: None Course Credit Hours: 3 credit hours Structure of Course: 45/0/0/0 Textbook:

More information

Thomas Disc Couplings Installation and Maintenance Type 54 RDG Sizes (Page 1 of 6)

Thomas Disc Couplings Installation and Maintenance Type 54 RDG Sizes (Page 1 of 6) Thomas Disc ouplings Installation and Maintenance Type 54 RDG Sizes 125-925 (Page 1 of 6) ATEX In order for this coupling to meet the ATEX requirements, it is mandatory to precisely follow these installation

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: O-Ring Groove Cutter Page 1 of 6 Kit Contents: 1x Cutter Head Assembly with Handle & Adjustable Tool Block 1x Graduated Adjusting Screw 1x Adjustable Tool Holder 1x Carbide Insert (Size of

More information

Suggested Methods of Mounting Free-Flex Pivots

Suggested Methods of Mounting Free-Flex Pivots Suggested Methods of Mounting Free-Flex Pivots For most applications, Riverhawk recommends orientation of the pivot to operate with a V c load condition. V c load is defined as a pure radial load located

More information

ANSI ORIFICE FLANGES METAL-KOREA

ANSI ORIFICE FLANGES METAL-KOREA METAL-KOREA ANSI ORIFICE FLANGES ORIFICE FLANGES are widely used in conjunction with orifice meters for measuring the rate of flow of liquids and gases. They are basically the same as standard welding

More information

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel

Important Note. Tools Required: Welder capable of fully welding 10 GA.135 steel INSTALLATION INSTRUCTIONS Frame Reinforcement Kit 11102 (Patent Pending) 1964-67 GM A-Body Coupe/2dr Sedan Read Instructions FULLY before starting Installation Important Note Installation of this kit requires

More information

INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT

INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT BACKGROUND Proper alignment of the transmission input shaft to the crankshaft centerline is required in order to achieve the best results

More information

FACULTY OF ENGINEERING DESIGN AND PRODUCTION ENGINEERING DEPARTMENT. Credit Hour System Metrology Lab 1 MDP 240. Sine Bars. Metrology laboratory

FACULTY OF ENGINEERING DESIGN AND PRODUCTION ENGINEERING DEPARTMENT. Credit Hour System Metrology Lab 1 MDP 240. Sine Bars. Metrology laboratory FACULTY OF ENGINEERING DESIGN AND PRODUCTION ENGINEERING DEPARTMENT Report On: Credit Hour System Metrology Lab 1 MDP 240 (13) Sine Bars Metrology laboratory Class No: B.N. Student Name Remark Signature

More information

Phone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels

Phone # La Jolla Doors. Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Phone # 800-440-8785 www.lajolladoors.com La Jolla Doors Block Frame Installation Manual Aluminum Frame with either Vinyl or Aluminum Panels Thank you for choosing La Jolla Doors In this manual you will

More information

Ford Pick Up Rear leaf Spring Kit Installation Instructions

Ford Pick Up Rear leaf Spring Kit Installation Instructions 1948-1956 Ford Pick Up Rear leaf Spring Kit Installation Instructions 1-800-984-6259 www.totalcostinvolved.com Parts 48 inch leaf (2) springs (4) U-bolts 3/8-24 x l 1/4bolts (16) & nuts (2) 1/2-20 x 4

More information

Industrial quality control HASO for ensuring the quality of NIR optical components

Industrial quality control HASO for ensuring the quality of NIR optical components Industrial quality control HASO for ensuring the quality of NIR optical components In the sector of industrial detection, the ability to massproduce reliable, high-quality optical components is synonymous

More information

Helpful Alignment Tips for Machine Shops

Helpful Alignment Tips for Machine Shops Table of Contents Background... 3 Offset or Centerline Misalignment... 3 Parallelism or Angular Misalignment... 4 Alignment Equipment Needed... 5 How it Works... 5 Measuring Procedure... 5 Making the Measurements...

More information

(Issued 1 Sept. 1971) CRD-C METHOD OF TEST FOR VERIFYING MACHINES FOR USE IN FLEXURAL STRENGTH TESTS OF CONCRETE MATTRESSES

(Issued 1 Sept. 1971) CRD-C METHOD OF TEST FOR VERIFYING MACHINES FOR USE IN FLEXURAL STRENGTH TESTS OF CONCRETE MATTRESSES 1. Scope (Issued 1 Sept. 1971) CRD-C 517-71 METHOD OF TEST FOR VERIFYING MACHINES FOR USE IN FLEXURAL STRENGTH TESTS OF CONCRETE MATTRESSES C 517 Revised 29 April 1971 1.1 This method describes the procedures

More information

Geometric Dimensioning and Tolerancing

Geometric Dimensioning and Tolerancing Geometric Dimensioning and Tolerancing (Known as GDT) What is GDT Helps ensure interchangeability of parts. Use is dictated by function and relationship of the part feature. It does not take the place

More information

Chapter 7. Optical Measurement and Interferometry

Chapter 7. Optical Measurement and Interferometry Chapter 7 Optical Measurement and Interferometry 1 Introduction Optical measurement provides a simple, easy, accurate and reliable means for carrying out inspection and measurements in the industry the

More information

Installation Instructions

Installation Instructions Installation Instructions XLC Series Self-aligning split bearing Experience In Motion 1 Equipment Check 1.1 Follow plant safety regulations prior to equipment disassembly: Lock out motor. Wear designated

More information

Type XTSR71 Sizes

Type XTSR71 Sizes (Page 1 of 13) s 494-5258 Type XTSR71 s 494-5258 Figure 1 Thomas XTSR71 Coupling 1. General Information 1.1 Thomas Couplings are designed to provide a mechanical connection between the rotating shafts

More information

Installation Instructions

Installation Instructions Installation Instructions XLC Generation 2 Self-aligning split bearing Experience In Motion 1 Equipment Check 1.1 Follow plant safety regulations prior to equipment disassembly: Lock out motor. Wear designated

More information

John Lodge s Body Fit Procedure

John Lodge s Body Fit Procedure John Lodge s Body Fit Procedure 12 By: John Lodge Bricklin Parts and Service Bedford, VA (ED. John Lodge has been working for Terry Tanner for 13 years. During that time John has strived to find a better

More information

Thomas Disc Couplings Installation and Maintenance Series 71 Sizes (Page 1 of 11) DANGER!

Thomas Disc Couplings Installation and Maintenance Series 71 Sizes (Page 1 of 11) DANGER! Thomas Disc s Installation and Maintenance Series 71 s 150-1038 (Page 1 of 11) This is the Original Document in English Language Figure 1 - Thomas Series 71 1. General Information 1.1. Thomas Series 71

More information

ISO INTERNATIONAL STANDARD. Laminate floor coverings Determination of geometrical characteristics

ISO INTERNATIONAL STANDARD. Laminate floor coverings Determination of geometrical characteristics Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 24337 First edition 2006-08-01 Laminate floor coverings Determination of geometrical characteristics Revêtements de sol stratifiés Détermination

More information

Case Study. Proficiency in Every Sense. Lockheed Martin - Joint Strike Fighter (JSF)

Case Study. Proficiency in Every Sense. Lockheed Martin - Joint Strike Fighter (JSF) Case Study Proficiency in Every Sense By Belinda Jones For the airplane aficionado, the appeal of the Joint Strike Fighter (JSF) is clearly its sleek, powerful contours and its stealth capacity. For the

More information

`48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line:

`48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line: `48-`56 Ford Pickup Rear leaf Spring Kit Installation Instructions Tech Line: 1-855-693-1259 www.totalcostinvolved.com CHECK ALL PARTS INCLUDED IN THIS KIT TO THE PARTS LIST BEFORE INSTALLING THE KIT.

More information

BHJ Products, Inc. Parts List & Instructions

BHJ Products, Inc. Parts List & Instructions Product Name: O-Ring Groove Cutter Adjustable Tool Block Upgrade Page 1 of 5 Prototype Kit Contents: 1x Adjustable Tool Block 1x Adjustable Tool Holder 1x Graduated Adjusting Screw 1x 1/8 Registration

More information

Product Guide Specification

Product Guide Specification HALFEN USA Inc. March 2012 8521 FM 1976 P.O. Box 547 Converse, TX 78109 Toll Free 800-423-9140 Fax 888-277-1695 Website www.halfenusa.com E-mail info@halfenusa.com Product Guide Specification Specifier

More information

An Adjustable Threading Feed Attachment for a Lathe Without Metric Threading Capability, by Ted Clarke

An Adjustable Threading Feed Attachment for a Lathe Without Metric Threading Capability, by Ted Clarke An Adjustable Threading Feed Attachment for a Lathe Without Metric Threading Capability by Ted Clarke Metric pitch threads, with the exception of the Royal Microscopical Society (RMS) 36 threads per inch

More information

The jigs and fixtures are the economical ways to produce a component in mass production system. These are special work holding and tool guiding device

The jigs and fixtures are the economical ways to produce a component in mass production system. These are special work holding and tool guiding device The jigs and fixtures are the economical ways to produce a component in mass production system. These are special work holding and tool guiding device Quality of the performance of a process largely influenced

More information

Agilent 10705A Single Beam Interferometer and Agilent 10704A Retroreflector

Agilent 10705A Single Beam Interferometer and Agilent 10704A Retroreflector 7B Agilent 10705A Single Beam Interferometer and Agilent 10704A Retroreflector Description Description The Agilent 10705A Single Beam Interferometer (shown in Figure 7B-1) is intended for use in low-mass

More information

Plane Mirror Interferometer Configurations. Functional description. Interferometeranordnung Plane Mirror Interferometer

Plane Mirror Interferometer Configurations. Functional description. Interferometeranordnung Plane Mirror Interferometer B Plane Mirror Interferometer Configurations Plane mirror interferometers are the ideal solution for special duty with a resolution of 1.25nm. Those used for distance, speed and acceleration measurement

More information

JOB QUALIFICATION STANDARD (JQS)

JOB QUALIFICATION STANDARD (JQS) Occupation: Work Process: Maintenance Mechanic Machine Shop Practical Hours: 250 hrs. JOB QUALIFICATION STANDARD (JQS) DOL Standard: Manual Machining Fundamentals: Apply a working knowledge of metal removal

More information

Technical Report Synopsis: Chapter 4: Mounting Individual Lenses Opto-Mechanical System Design Paul R. Yoder, Jr.

Technical Report Synopsis: Chapter 4: Mounting Individual Lenses Opto-Mechanical System Design Paul R. Yoder, Jr. Technical Report Synopsis: Chapter 4: Mounting Individual Lenses Opto-Mechanical System Design Paul R. Yoder, Jr. Introduction Chapter 4 of Opto-Mechanical Systems Design by Paul R. Yoder, Jr. is an introduction

More information

F-150 Structural Holding System

F-150 Structural Holding System F-150 Structural Holding System Users Manual December 2013 by Vehicle Service Group. All rights reserved. CO8812.2 502073 Rev. - 12/11/2013 CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive

More information

POWER PEAK TM ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation. Version 1, Rev D P/N

POWER PEAK TM ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation. Version 1, Rev D P/N POWER PEAK TM ASSEMBLY ISTRUCTIOS step-by-step assembly and installation Version 1, Rev D P/ 5803028 The Power Peak TM A few words about this product The Power Peak is designed to mount on standard I-Beams

More information

WARNING. BX Suzuki Sidekick 4 Door/ 4WD Geo Tracker 4 Door/ 2WD/ 4WD Installation Instructions. Serial Number

WARNING. BX Suzuki Sidekick 4 Door/ 4WD Geo Tracker 4 Door/ 2WD/ 4WD Installation Instructions. Serial Number 1991-98 Suzuki Sidekick 4 Door/ 4WD 1996-97 Geo Tracker 4 Door/ 2WD/ 4WD Serial Number Please read BOTH these Installation Instructions and the General Instructions before attempting to install or operate

More information

Measurement. Name: Slot: Essential Math 12 Mr. Morin. Accuracy, Precision and Uncertainty Tolerance

Measurement. Name: Slot: Essential Math 12 Mr. Morin. Accuracy, Precision and Uncertainty Tolerance Measurement Essential Math 12 Mr. Morin Name: Slot: Accuracy, Precision and Uncertainty Tolerance 1 Accuracy, Precision, and Uncertainty Accuracy The measurement is considered accurate if it is taken correctly,

More information

Software Validation Considerations within Medical Companies per FDA 21 CFR PART 11

Software Validation Considerations within Medical Companies per FDA 21 CFR PART 11 Greg Hetland, Ph.D. International Institute of GD&T Software Validation Considerations within Medical Companies per FDA 21 CFR PART 11 One critical challenge facing today s medical OEMs and suppliers is

More information

Square Shear Beam Mounting Guidelines

Square Shear Beam Mounting Guidelines Issue Date: January 2016 Please Retain for Future Reference 2016-01-11 Square Shear Beam Mounting Guidelines Subject: Square Shear Beam Recommendations Introduction: Even though Digi-Star load cells are

More information

INSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ

INSTALLATION INSTRUCTIONS 3/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting

More information

Position Accuracy Machines for Selective Soldering Fine Pitch Components Gerjan Diepstraten Vitronics Soltec B.V. Oosterhout, Netherlands

Position Accuracy Machines for Selective Soldering Fine Pitch Components Gerjan Diepstraten Vitronics Soltec B.V. Oosterhout, Netherlands As originally published in the IPC APEX EXPO Conference Proceedings. Position Accuracy Machines for Selective Soldering Fine Pitch Components Gerjan Diepstraten Vitronics Soltec B.V. Oosterhout, Netherlands

More information

Section 9: Standard & Optional Machine Features

Section 9: Standard & Optional Machine Features Rotary Attachment The optional Rotary Attachment allows you to mark, engrave or cut cylindrical objects. The Rotary Attachment works in both raster and vector modes. Follow the instructions below to install

More information

1949 to 1954 Chevrolet Dual Master Cylinder Conversion

1949 to 1954 Chevrolet Dual Master Cylinder Conversion 1949 to 1954 Chevrolet Dual Master Cylinder Conversion This document is a one stop shop to getting your brake system updated on your old Chevy. Whether you re going with a disc conversion or just sticking

More information

Advanced Dimensional Management LLC

Advanced Dimensional Management LLC Index: Mechanical Tolerance Stackup and Analysis Bryan R. Fischer Accuracy and precision 8-9 Advanced Dimensional Management 14, 21, 78, 118, 208, 251, 286, 329-366 Ambiguity 4, 8-14 ASME B89 48 ASME Y14.5M-1994

More information

Answers to Questions and Problems

Answers to Questions and Problems Fundamentals of Geometric Dimensioning and Tolerancing Using Critical Thinking Skills 3 rd Edition By Alex Krulikowski Answers to Questions and Problems Second Printing Product #: 1103 Price: $25.00 Copyright

More information

Fabrication, Assembly and Testing of a new X-Y Flexure Stage with substantially zero Parasitic Error Motions. Fig.1 Experimental Set-up

Fabrication, Assembly and Testing of a new X-Y Flexure Stage with substantially zero Parasitic Error Motions. Fig.1 Experimental Set-up Fabrication, Assembly and Testing of a new X-Y Flexure Stage with substantially zero Parasitic Error Motions Shorya Awtar Precision Engineering Research Group, MIT Cap-probe Driver Flexure Plate and Metrology

More information

THE STORAGE RING CONTROL NETWORK OF NSLS-II

THE STORAGE RING CONTROL NETWORK OF NSLS-II THE STORAGE RING CONTROL NETWORK OF NSLS-II C. Yu #, F. Karl, M. Ilardo, M. Ke, C. Spataro, S. Sharma, BNL, Upton, NY, 11973, USA Abstract NSLS-II requires ±100 micron alignment precision to adjacent girders

More information

LEITZ SIRIO LINE VERSION

LEITZ SIRIO LINE VERSION LEITZ SIRIO LINE VERSION 2017-6 LEITZ SIRIO LINE VERSION 2017-6 TECHNICAL DATA Description High-speed measuring machines for quality control in the shop floor. With integrated continous rotary table and

More information

Difrotec Product & Services. Ultra high accuracy interferometry & custom optical solutions

Difrotec Product & Services. Ultra high accuracy interferometry & custom optical solutions Difrotec Product & Services Ultra high accuracy interferometry & custom optical solutions Content 1. Overview 2. Interferometer D7 3. Benefits 4. Measurements 5. Specifications 6. Applications 7. Cases

More information

LAT Interface Survey Analysis Report

LAT Interface Survey Analysis Report LAT-TD LAT-TD-07690-02 TD-07690-0202 13 13 September September 2006 2006 LAT Interface Survey Analysis Report Martin Martin Nordby Nordby Ken Ken Fouts Fouts Catherine Catherine LeCocq LeCocq Dave Dave

More information

Vertical Struts. P16603: Work Piece Movement Jonathan Sanabria April 19, Contents

Vertical Struts. P16603: Work Piece Movement Jonathan Sanabria April 19, Contents Vertical Struts P16603: Work Piece Movement Jonathan Sanabria April 19, 2016 Contents Overview Assumptions for Research/Design Summary of Research Summary of Design Moving Forward Overview The primary

More information

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad Name Code INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad -500 043 MECHANICAL ENGINEERING TUTORIAL QUESTION BANK : ENGINEERING METROLOGY : A50318 Class : III B.Tech I Semester Branch

More information

INSTRUCTIONS for WOODY RACK ON STANDARD FLEETSIDE TRUCKS WARNING: Do NOT attempt to install or use this rack without following all instructions.

INSTRUCTIONS for WOODY RACK ON STANDARD FLEETSIDE TRUCKS WARNING: Do NOT attempt to install or use this rack without following all instructions. 8JUL15 U.S. RACK, Inc. - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTRUCTIONS for WOODY RACK ON STANDARD FLEETSIDE TRUCKS WARNING: Do NOT attempt to install or use this rack without following

More information

Brochure Includes: Set-up Instructions Operating Instructions Parts List Fundamentals of Drill Sharpening. Patent 3,952,459

Brochure Includes: Set-up Instructions Operating Instructions Parts List Fundamentals of Drill Sharpening. Patent 3,952,459 Patent 3,952,459 Brochure Includes: Set-up Instructions Operating Instructions Parts List Fundamentals of Drill Sharpening Accurately Sharpens most drills bits. Now, with this one low-cost, simple machine,

More information

Engineering Working Drawings Basics

Engineering Working Drawings Basics Engineering Working Drawings Basics Engineering graphics is an effective way of communicating technical ideas and it is an essential tool in engineering design where most of the design process is graphically

More information

BEAST THE. Tube and Pipe Notcher Operating Instructions. Notches In Bends Straight Notches. Angled Notches. Offset Notches

BEAST THE. Tube and Pipe Notcher Operating Instructions. Notches In Bends Straight Notches. Angled Notches. Offset Notches Copyright (c) 2007 J D SQUARED INC. www.jd2.com THE BEAST Tube and Pipe Notcher Operating Instructions Notches In Bends Straight Notches Angled Notches PATENT PENDING Offset Notches Assembly After unpacking

More information

Gaging Exploration (Applications)

Gaging Exploration (Applications) Gaging Exploration (Applications) PMPA Technical Conference Tomorrow is Today - Conquering the Skills Challenge Chicago, IL April 24, 2018 Gary K. Griffith Corona, California Gary K. Griffith 50+ Years

More information

Eric B. Burgh University of Wisconsin. 1. Scope

Eric B. Burgh University of Wisconsin. 1. Scope Southern African Large Telescope Prime Focus Imaging Spectrograph Optical Integration and Testing Plan Document Number: SALT-3160BP0001 Revision 5.0 2007 July 3 Eric B. Burgh University of Wisconsin 1.

More information

ESA-300 Full Breakout

ESA-300 Full Breakout Interior View 0 Installation Instructions For use with ESA II Controler DORMA AUTOMATICS, Inc. 94 Sherwood Drive Toll-Free: 877-67-6 DL844-00 Lake Bluff, IL 60044 Fax: 877-4-7999 Rev. /07 Tools Required:

More information

NX 7.5. Table of Contents. Lesson 3 More Features

NX 7.5. Table of Contents. Lesson 3 More Features NX 7.5 Lesson 3 More Features Pre-reqs/Technical Skills Basic computer use Completion of NX 7.5 Lessons 1&2 Expectations Read lesson material Implement steps in software while reading through lesson material

More information

UNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS

UNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS UNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS 5.1 Introduction Orthographic views are 2D images of a 3D object obtained by viewing it from different orthogonal directions. Six principal views are possible

More information

Measuring systems for ironing rings and punches

Measuring systems for ironing rings and punches Measuring systems for ironing rings and punches Equipment and proven technology for precision tooling measurement in beverage can industry RINGMASTER THE MASTER TOOL FOR RING MEASURE MENT RINGMASTER provides

More information

production competitive Quality Vision International Defines Accuracy Townsend Machine Transforms Their Business New Makino a51nx and

production competitive Quality Vision International Defines Accuracy Townsend Machine Transforms Their Business New Makino a51nx and The publication from Makino that produces more competitive companies competitive production Volume 6 Number 1 Quality Vision International Defines Accuracy Townsend Machine EVOLVES Family-Grown COMPANY

More information

Application of Guided Wave Technology to Tube Inspection

Application of Guided Wave Technology to Tube Inspection ECNDT 2006 - Th.3.1.5 Application of Guided Wave Technology to Tube Inspection T. VOGT, D. ALLEYNE, B. PAVLAKOVIC, Guided Ultrasonics Limited, Nottingham, United Kingdom 1. Introduction Abstract. The inspection

More information

PTICALTARGETING SPECIALTIES

PTICALTARGETING SPECIALTIES PTICALTARGETING SPECIALTIES 1 2 3 FOUNDATION TARGET INSERT FTI CONSTRUCTION BALL / TARGET PAD CBTP TARGET PAD TRP 3 1/2-8 TO 5/8-11 INSTRUMENT ADAPTOR 4 MAGNETIC BASE TARGET HOLDER ADAPTOR MBTHA CONSTRUCTION

More information

Installation Instructions Universal Crossmember Kit - 60 Track Width BEFORE Measure Twice, Weld Once! II

Installation Instructions Universal Crossmember Kit - 60 Track Width BEFORE Measure Twice, Weld Once! II Installation Instructions Universal Crossmember Kit - 60 Track Width Please read these instructions completely BEFORE starting your installation. Remember the basic rule for a successful installation:

More information

GEARBOX CONSTRUCTION E.M.G.S. MANUAL ( 9) The Girder Gearbox

GEARBOX CONSTRUCTION E.M.G.S. MANUAL ( 9) The Girder Gearbox GEARBOX CONSTRUCTION SHEET 1 The author, having been disappointed with a few of the commercially available gearboxes, decided to design and construct something to his own design. The Girder Gearbox Application

More information

Premium portable metrology. ModelMaker. Handheld scanners. MCAx. Articulated arms NIKON METROLOGY I VISION BEYOND PRECISION

Premium portable metrology. ModelMaker. Handheld scanners. MCAx. Articulated arms NIKON METROLOGY I VISION BEYOND PRECISION Premium portable metrology Handheld scanners MCAx Articulated arms NIKON METROLOGY I VISION BEYOND PRECISION MODELMAKER H120 Ultra-fast high-definition 3D scanning More than two decades since the inception

More information

CD42-STS Operating Manual Diver/ROV Pipeline Pig Location & Tracking System

CD42-STS Operating Manual Diver/ROV Pipeline Pig Location & Tracking System CD42-STS Operating Manual Diver/ROV Pipeline Pig Location & Tracking System March 8, 2011 1801 North Juniper Avenue Broken Arrow, Oklahoma 74012 USA 1 (800) 580-4234 USA & Canada Toll free 1 (918) 258-6068

More information

Comp-DS Driveshaft. User Manual B

Comp-DS Driveshaft. User Manual B Comp-DS Driveshaft User Manual 2010-1378B Driveshaft Parts List 1.22B 1.21C 1.22C 1.22D 1.21A 1.21B 1.22A 1.1 Figure 1 1.0 Complete Driveshaft 1.1 Tube and Flange Assembly 1.2 Coupling Assembly (2 required

More information

SAFETY INSTRUCTIONS. Wear protective clothing, including safety glasses and steel toe boots.

SAFETY INSTRUCTIONS. Wear protective clothing, including safety glasses and steel toe boots. SAFETY INSTRUCTIONS Wear protective clothing, including safety glasses and steel toe boots. DO NOT allow loose clothing or long hair near machine operations. Keep work site and machine clean. Use brush

More information

CMM-Manager Fully featured metrology software for CNC, manual and portable CMMs

CMM-Manager Fully featured metrology software for CNC, manual and portable CMMs Ryf AG Bettlachstrasse 2 2540 Grenchen tel 032 654 21 00 fax 032 654 21 09 www.ryfag.ch CMM-Manager Fully featured metrology software for CNC, manual and portable CMMs NIKON METROLOGY I VISION BEYOND PRECISION

More information

American Safe Room. Explosion Resistant Blast Hatch with Integrated Riser

American Safe Room. Explosion Resistant Blast Hatch with Integrated Riser American Safe Room Explosion Resistant Blast Hatch with Integrated Riser Drawing: ASR-50-RBH Revision: H May 17, 2012 Table of Contents Description... 3 Options... 4 Order form... 5 Option: left or right

More information

gage 2000 FLEXIBLE MEASURING SYSTEM shaping the future of measurement

gage 2000 FLEXIBLE MEASURING SYSTEM shaping the future of measurement gage 2000 THE ULTIMATE FLEIBLE MEASURING SSTEM shaping the future of measurement GAGE 2000 R WILL CHANGE THE WA OU MEASURE All-aluminum construction improves thermal, dimensional/torsional, and geometric

More information

OPERATION AND MAINTENANCE MANUAL TRIAXIAL ACCELEROMETER MODEL PA-23 STOCK NO

OPERATION AND MAINTENANCE MANUAL TRIAXIAL ACCELEROMETER MODEL PA-23 STOCK NO OPERATION AND MAINTENANCE MANUAL TRIAXIAL ACCELEROMETER MODEL PA-23 STOCK NO. 990-60700-9801 GEOTECH INSTRUMENTS, LLC 10755 SANDEN DRIVE DALLAS, TEXAS 75238-1336 TEL: (214) 221-0000 FAX: (214) 343-4400

More information

Laser Technology Improves and Makes Easier Post-Process Measuring On Centreless Grinders. Application Note. A. Spizzamiglio - Aeroel - Italy SUMMARY:

Laser Technology Improves and Makes Easier Post-Process Measuring On Centreless Grinders. Application Note. A. Spizzamiglio - Aeroel - Italy SUMMARY: Application Note Laser Technology Improves and Makes Easier Post-Process Measuring On Centreless Grinders. SUMMARY: Introduction Laser Technology sets new performance standards Application for centreless

More information

What s New in SA SA Repeat Alignments

What s New in SA SA Repeat Alignments What s New in SA SA 2012.12.06 Repeat Alignments To Repeat an Instrument s Alignment: Any instrument s alignment can now be repeated, making alignments as part of a repeatable process easier to set up.

More information

RLP Mini Low Profile V Track Hardware sliding door hardware/ barn door track

RLP Mini Low Profile V Track Hardware sliding door hardware/ barn door track Page 1 of 9 Installation Suggestions for: RLP Mini Low Profile V Track Hardware sliding door hardware/ barn door track Read these instructions to end before starting installation or ordering hardware.

More information

MODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS

MODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS MODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS FOR MODELS MFD. SINCE 10/17 For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Rails Rollers Reversible

More information

REV A.1 CMCP810PC SERIES RUNOUT KIT INSTRUCTION MANUAL STI VIBRATION MONITORING INC

REV A.1 CMCP810PC SERIES RUNOUT KIT INSTRUCTION MANUAL STI VIBRATION MONITORING INC REV A.1 CMCP810PC SERIES RUNOUT KIT INSTRUCTION MANUAL STI VIBRATION MONITORING INC WWW.STIWEB.COM About the Runout Kit The CMCP810PC Series Electrical Runout Kit uses industry standard sensors to detect

More information

Extra Wide Heavy Duty Plastic Lockers Series Locker Installation Instructions

Extra Wide Heavy Duty Plastic Lockers Series Locker Installation Instructions Locker Installation Instructions Thank you for selecting Extra Wide Heavy Duty Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These

More information

From Plate Materials & Services - To To COMPLETE PRESS FRAMES

From Plate Materials & Services - To To COMPLETE PRESS FRAMES From Plate Materials & Services - To To COMPLETE PRESS FRAMES Press Press Weldments Weldments & & Assemblies: Assemblies: Superior has Superior has specialized specialized in these in these unique Heavy

More information

understanding the ISO performance standard

understanding the ISO performance standard TM understanding the ISO 10360-2 performance standard World Headquarters Precision Park, 200 renchtown Road North Kingstown, RI 02852-1700 Tel: (800) 766-4673 (401) 886-2000 ax: (800) 933-2937 (401) 886-2762

More information

Gram Gage for Measuring Action Center Friction

Gram Gage for Measuring Action Center Friction Gram Gage for Measuring Action Center Friction Greg Graham, RPT, March 11, 2011 If you have been measuring action center friction with nothing but your hands and a Correx gage, there is a better way. This

More information

Chapter 14 Automation of Manufacturing Processes and Systems

Chapter 14 Automation of Manufacturing Processes and Systems Chapter 14 Automation of Manufacturing Processes and Systems Topics in Chapter 14 FIGURE 14.1 Outline of topics described in this chapter. Date 1500Ğ1600 1600Ğ1700 1700Ğ1800 1800Ğ1900 Development Water

More information

General machining, fitting and assembly applications

General machining, fitting and assembly applications Unit 065 General machining, fitting and assembly Level: 2 Credit value: 12 NDAQ number: 500/9514/6 Unit aim This unit covers the skills and knowledge needed to prove the competences required to cover a

More information

5 m-measurement system for traceable measurements of tapes and rules

5 m-measurement system for traceable measurements of tapes and rules 5 m-measurement system for traceable measurements of tapes and rules Tanfer Yandayan*, Bulent Ozgur Tubitak Ulusal Metroloji Enstitusu (UME) PK54, 4147 Gebze-KOCAELI / TURKEY ABSTRACT Line standards such

More information

FAQver. CARTER PRODUCTS. Laser Computer Pattern Projection Systems FREQUENTLY ASKEDQUESTIONS

FAQver. CARTER PRODUCTS. Laser Computer Pattern Projection Systems FREQUENTLY ASKEDQUESTIONS FAQver. CARTER PRODUCTS Laser Computer Pattern Projection Systems FREQUENTLY ASKEDQUESTIONS 2007 CARTER PRODUCTS COMPANY 2871 Northridge Drive NW Grand Rapids, MI 49544 Toll Free (888) 622-7837 Phone (616)

More information

SQ2 User Instructions SQ2 Overview:

SQ2 User Instructions SQ2 Overview: SQ2 User Instructions SQ2 Overview: The stationary circular saws including table, radial and chop saws are arguably the most important tools in the shop. They may also be the most difficult to reliably

More information

J D SQUARED INC. NOTCH MASTER Tube and Pipe Notcher Operating Instructions

J D SQUARED INC.   NOTCH MASTER Tube and Pipe Notcher Operating Instructions Copyright (c) 2006 J D SQUARED INC. www.jd2.com NOTCH MASTER Tube and Pipe Notcher Operating Instructions Angled Notches PATENT PENDING Straight Notches Offset Notches Tube Clamp Slider Tube Clamp Exploded

More information

Installation Instructions

Installation Instructions Installation Instructions Circpac MD Split Segmented Circumferential Gas Seal Experience In Motion 1 Equipment Check and Seal Preparation 1.1 Refer to Figure 1 for sleeve/shaft and equipment requirements.

More information