FischerTHERM plusdach
|
|
- Jemimah James
- 6 years ago
- Views:
Transcription
1 FischerTHERM plusdach * An enterprise of Corus Building Systems
2
3 FischerTHERM plusdach concealed fastening The FischerTHERM plusdach roof, with the Fischer plus-rail The FischerTHERM plusdach roof can be used when the visible sealing screws on FischerTHERM roof elements are undesirable. The FischerTHERM plusdach roof consists of the roof element, the plusrail and the corresponding type 4- aluzinc spherical caps. The plus-rail is fastened safely and permanently by clicking it into place over the spherical cap. This combines the many positive features of the FischerTHERM roof elements with the additional aesthetic appeal of the concealed sealing screws. If fastening is performed in the crown, spherical caps are placed on the sealing screws in the purlin area. This is also the case with the longitudinal joint connection, spaced at 0 mm. The plus-rail is supplied in exactly the same surface design as the corresponding outer skin of the FischerTHERM roof element. The sheet thick-ness of the plus-rail is 0. mm, weight 0. kg/m. Standard length 000 mm. It is even possible to produce a Fischer- THERM plusdach roof by subsequently adding the plus-rail and spherical caps. Double safety As the plus-rail can additionally be applied to FischerTHERM roof elements, million m² of which have been tried and trusted, this means double safety against possible leaks. Even without the plus-rail, the roof system offers a high degree of safety against rainfall. The plus-rail can not only be employed in the vicinity of the longitudinal joint but also on the two intermediate ribs of the roof elements. This is important above all for the edge and corner areas with high suction loads. Here, too, the sealing screws are concealed under the plus-rail., R0,0 Continuous manufacture of the plus-rail, R0 à,0 Fischer plus-rail on longitudinal jointing, R0 à,0 Fischer plus-rail, drilling screw with spherical cap every 0 mm between purlin area ➀ Fischer plus-rail ➁ self-sealing screw. x... E ➂ spherical cap 4- (Aluzinc) ➃ purlin ➄ drilling screw. x -E 4 4 Fischer plus-rail on intermediate ribs ➀ Fischer plus-rail ➁ self-sealing screw. x... E ➂ spherical cap 4- (Aluzinc) ➃ purlin ➄ drilling screw. x -E Fischer plus-rail, drilling screw with spherical cap every 0 mm between purlin area
4 FischerTHERM plusdach - Easy to install Butt-jointed or overlapping These are the two possible methods of applying the plus-rail to the spherical caps. The FischerTHERM plusdach roof element is ready to use and tightly sealed without the additional plus-rail. Buttjointing is the easiest and best solution as there are no special technical details to observe such as connection to the ridge or eaves - when installing. The butt joint itself is always near a spherical cap at a distance of 00 mm from the end of the rail. The few drops of water that could penetrate the small butt joint shouldn t be a problem. However, if the roof has a low eaves height or the eaves can easily be seen due to a large roof pitch, the end flashing of the eaves should be mounted over the prof the eaves should be mounted over the plus-rail for optical reasons. (see detail page, top left). The FischerTHERM plusdach roof can also use an overlapping plus-rail. Here, the plus-rail are overlapped on the end lap jointing and pressed onto the spherical caps. With the aid of spacers, the higher edge profiles overlap the plus-rail, for example, on the ridge. (see detail page ) Special features: improved optical appeal through concealed sealing screws additional safety through two sealing levels can be installed on existing construction easy assembly Fischer plus rail butt jointed Fischer plus rail overlapping FischerTHERM roof elements DL 0 / 0 / 00 / 0 / 40 / 0 A 0 40, B 000 Panel Type sheet thickness t [mm] outerskin ta [mm] innerskin ti [mm] panel gauge d [mm] panel length max. L [m] panel weight g [kg/m ] heat transmission coefficient U [W/(m K)] heat transmission resistance R [m K/W] FischerTHERM DL 0 0 0, 0,, DL 0 0 0, 0,4, DL 00 00, 0,,4 0, 0,4.) DL 0 0, 0,, DL 40 40,4 0, 4,0 DL 0 0, 0,0 4,.. ) recommended max. length ) available on request 4
5 Assembly The FischerTHERM plusdach roof can be assembled easily and quickly. Sealing screws with spherical caps are attached to the crown of the FischerTHERM roof elements for clip fastening the Fischer plus-rail. In order to facilitate the alignment of the spherical caps, these are first measured up and placed in the gable verge area of the roof surface. A uniform distance of the remaining spherical caps is achieved using a piece of cord. In the longitudinal jointing of the roof elements drilling screws are used spaced at a distance of 0. If additional sealing screws are used in the purlins through the intermediate ribs of the roof elements, for example in the gable verge area due to the increased suction loads there, the distance between the spherical caps between them will also be 0. 0 Finally the plus-rail is laid on top of the mounted spherical caps and pressed on with the foot until it noticably slots into place and is this thus securely locked laterally ont othe spherical cap.
6 FischerTHERM plusdach the secure fastening Simple procedure for determining the required spherical caps and the number of Fischer plus-rails, whereby all sealing screws are concealed. Permitted purlin distances L [m]: a) with load (snow load): see brochure Manufacturing Programme / Load Tables FischerTHERM b) with wind suction: Building height 0- m permitted purlin distance L.0 m* Building height -0 m permitted purlin distance L.00 m* * Values for closed buildings, same spans for multispan supports. No jibs. Roof plan of purlin position gable verge 0-40 sheet thickness t: outerskin = 0. mm, innerskin = 0. mm edge edge area Normal area area a/ eaves a/ FischerTHERM elements purlin ridge a L purlins For building heights over 0 m and purlin distances greater than m and/or.0 m, we will provide you with a static calculation. long side b eaves Edge area [a/]**: Fischer plus-rail in the longitudinal jointing area and on each intermediate rib. ** a : is is always the narrow side Normal area: Fischer plus-rail only in the longitudinal jointing area (see page for element fastening) Fasteners Structure Steel and reinforoed concrete substructure with steel mm FischerTHERM-Roof Elements DL 0 DL 0 DL 00 DL 0 DL 40 DL 0 Stainless steel sealing screws JZ-. x 0 JZ-. x 00 JZ-. x JZ-. x 0 JZ-. x JZ-. x 00 -E -E -E -E -E -E incl. spherical cap incl. spherical cap incl. spherical cap incl. spherical cap incl. spherical cap incl. spherical cap Typ 4- Typ 4- Typ 4- Typ 4- Typ 4- Typ 4- Timber JA-. x 0 JA-. x 0 JA-. x JA-. x 00 JA-. x 0 JA-. x 0 -E -E -E -E -E -E incl. spherical cap incl. spherical cap incl. spherical cap incl. spherical cap incl. spherical cap incl. spherical cap Typ 4- Typ 4- Typ 4- Typ 4- Typ 4- Typ 4- Longitudinal jointing JT-H- JT-H- JT-H- JT-H- JT-H- JT-H-. x. x. x. x. x. x -E -E -E -E -E -E incl. spherical cap incl. spherical cap incl. spherical cap incl. spherical cap incl. spherical cap incl. spherical cap Type 4- Type 4- Type 4- Type 4- Type 4- Type 4- (distance (distance (distance (distance (distance (distance 0 mm) 0 mm) 0 mm) 0 mm) 0 mm) 0 mm) Only fastening elements as per IFBS Z licence may be used. For other types of screw see Flashings and Accessories
7 Element fastening on FischerTHERM plusdach as per plan, page Building height 0- m, purlin distanze.0 m Edge area [a/]: in the longitudinal jointing area and on each intermediate rib sealing screw incl. spherical cap per purlin support intermediate rip longitudinal joint a/ Normal area: Only in longitudinal jointing area sealing screw incl. spherical cap per purlin support Building height -0 m, purlin distanze.00 m Edge area [a/]: in the longitudinal jointing area and on each intermediate rib sealing screw incl. spherical cap per purlin support a/ Normal area: Only in longitudinal jointing area screws incl. spherical caps per purlin support spaced at e = 0 mm. sealing screws and spherical caps distance e = 0 mm jib of the plus-rail 0 max. 0
8 FischerTHERM plusdach Details The depicted details have been designed in such a way as to fulfil the following requirements as far as possible: few thermal bridges,as airtight as possible, rain-proof, pleasing to the eye, durable, simple to assemble, inexpensive. Fischer plus-rail butt jointed Industrial Guttering Ridge 0 0 a a) Alternatively: Bend up the valley of the outer skin. One flute closer on each side of the roof is then sufficient. Mono-ridge a 0 Gable Verge a) Alternatively: Bend up the valley of the outer skin. One flute closer on each side of the roof is then sufficient. 4 FischerTHERM plusdach FischerTHERM Verge capping 4 Angle support Purlin Bracket Rail Bracket Z-profile 0 Self-sealing screw. x... - E Drilling screw. x... - E Blind rivet AI/E - Ø 4. x. Assembly foam PUR-M, (dampen ends of elements) 4 Self-sealing screw. x... - E Permanently elastic strip sealant, single-sided self-adhesive, illac 0 x 4 Spherical cap 4- (aluzinc) Fischer plus-rail Blind rivet AI/E - Ø 4. x. Permanently elastic precompressed strip sealant, single-sided self-adhesive, illmod SFI 0 x - 0 Verge capping Toothed flashing Profile filler strips (attach with silicon) Permanently elastic precompressed strip sealant, single-sided self-adhesive, illmod SFI 0 x - 4 Guttering support Guttering Gutter flashing Hard fibre strip between guttering profiles Gattering Purlin Spacer 0 End flashing Ridge profile Drilling screw. x - E Self-sealing screw. x... - E 4 Drilling screw. x - E Ridge profile interior Tie bolt
9 Fischer plus-rail overlapping Industrial Guttering (with spacer profile / overlapping) 4 Ridge (with spacer profile / overlapping) 4 a a) Alternatively: Bend up the valley of the outer skin. One flute closer on each side of the roof is then sufficient. Mono-ridge (with spacer profile / overlapping) 4 a 0 0 a) Alternatively: Bend up the valley of the outer skin. One flute closer on each side of the roof is then sufficient. FischerTHERM plusdach Fischer plus-rail Spherical cap 4- (aluzinc) 4 Self-sealing screw. x... - E End flashing, overlapping Blind rivet AI/E - Ø 4, x, EPDM spacer profile FischerTHERM Self-sealing screw. x... - E 0 Permanently elastic precompressed strip sealant, single-sided self-adhesive, illmod SFI 0 x - Guttering support Guttering Gutter flashing 4 Permanently elastic strip sealant, single-sided self-adhesive, illac 0 x 4 Hard fibre strip between guttering profiles Purlin Spacer Purlin Bracket 0 Drilling screw. x - E Ridge profile, overlapping Drilling screw. x - E Toothed flashing 4 Self-sealing screw. x... - E Profile filler strips (attach with silicon) Assembly foam PUR-M, (dampen ends of elements) Ridge profile interior Tie bolt Verge capping, overlapping 0 Rail Bracket
10 FischerTHERM plusdach Details Skylight connectors (lengthways to the roof element) Skylight connectors (transversally to the roof element) a 4 4 a) Alternatively: Bend up the valley of the outer skin. One flute closer on each side of the roof is then sufficient. Axial section (fastening distance) Overlapping mind. 0 mm mm 00 mm 4 Butt jointed 00 mm 00 mm FischerTHERM plusdach Fischer plus-rail Spherical cap 4- (aluzinc) 4 Connecting profile, special flashing Z-profile Drilling screw. x - E Permanently elastic strip sealant, single-sided self-adhesive,illac 0 x 4 Self-sealing screw. x... - E Self-sealing screw. x... - E 0 Skylight frame, self-supporting, by customer Thermal insulation, by customer Permanently elastic pre-compressed strip sealant, single-sided self-adhesive, illmod SFI 0 x - Thermal insulation spread flat, not supplied 4 Purlin Bracket Drilling screw. x - E Connecting profile, special flashing Toothed flashing Profile filler strips (attach with silicon) 0 Blind rivet Ai/E - Ø 4. x. Skylight frame, self-supporting, not supplied Assembly foam PUR-M, (dampen ends of elements) Skylight 0
11 Skylight dome connection (eaves) Skylight dome connection (ridge) 0 0 eaves Traufe 4 b 4 ridge First b = foam-free area Skylight dome connection (along the element) 0 4 FischerTHERM plusdach Fischer plus-rail Spherical cap 4- (aluzinc) 4 Self-sealing screw. x... - E Permanently elastic precompressed strip sealant, single-sided self-adhesive, illmod SFI 0 x - Permanently elastic strip sealant, single-sided self-adhesive,illac 0 x 4 Rail, lengthwise Rail, traverse Skylight dome connector 0 Skylight dome Drilling screw. x - E
12 Product range FischerTHERM FischerTRAPEZ FischerTRAPEZ-Acoustic FischerKASSETTE FischerKASSETTE-Acoustic FischerWELLE FischerPANEEL FischerKLIPTEC Flashings and accessories Fischer Profil GmbH Waldstraße D-0 Netphen-Deuz Telefon +4 (0) / 0- Telefax +4 (0) / 0- info@fischerprofil.de Diese Informationen sind nach bestem Wissen und Gewissen erstellt worden. Corus plc einschließlich ihrer Tochtergesellschaften übernimmt jedoch keine Haftung für Informationen, die sich eventuell als irreführend herausstellen könnten. Reproduktion und Nachdruck verboten Data subject to change without notice
FischerTHERM plusdach The Sandwichelement with the special something
The Sandwichelement with the special something Contents Page General Product Range 4 Fasteners 5 Secure fastening 7 Assembly 8 9 Details 0 References 4-5 FischerProfil 05 FischerTHERM plusdach The first
More informationFischerKLIPTEC. * An enterprise of Corus Distribution & Building Systems
50 FischerKLIPTEC * An enterprise of Corus Distribution & Building Systems FischerKLIPTEC Easy assembly using clip connections FischerKLIPTEC - the new roof system from Fischer Profil consists in its surface
More informationFischerKLIPTEC. * A Tata Steel Enterprise
50 FischerKLIPTEC * A Tata Steel Enterprise FischerKLIPTEC Easy assembly using clip connections FischerKLIPTEC - the new roof system from Fischer Profil consists in its surface of just one building element.
More informationSpeedDeck. Fixing and Handling Guide
SpeedDeck Section 1 Delivery/Storing On Site/Handling l SpeedDeck is factory or on-site manufactured. l Straight SpeedDeck bundles are a maximum 1 tonne, sheets nestled and banded with polypropylene or
More informationVerge Flashing. Verge Flashing. Only use if flashings requirements can be site measured before ordering. Verge Clip
Tolerance Detail (recommended) Verge Closure Verge Channel Verge Clip Verge Flashing VERGE CHANNEL RIVETTED TO EUROSEAM AT APPROX 400MM CENTRES USING 4.8 X 12MM RIVETS. NB: DO NOT RIVET AT HALTER POSITION
More informationEverbright E610 polycarbonate light panels Installation guidance
Everbright E610 polycarbonate light panels Installation guidance Mono-pitched applications: Eaves For pitched roofs above 0-degree fix aluminium angle EL17 to supporting structure with self drilling screws
More informationGLOSSARY OF TERMS SECTION 8
GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the
More informationThermoSpan EPS. Metalcraft COMMERCIAL ROOFING CREPS. Insulated Panel Systems DETAIL LIST
ThermoSpan EPS DETAIL LIST 00 / 15 COVER SHEET 01 / 15 RIDGE DETAIL 02 / 15 HEAD FLASHING DETAIL 03 / 15 EAVES GUTTER DETAIL 04 / 15 INSULATED GUTTER 05 / 15 INSULATED BOX GUTTER 06 / 15 BARGE CAPPING
More informationConstruction details: Master-C type profiles and joints:
Construction details: Master-C type profiles and joints: Master-C 3g 32 mm. (1 1/4 ) 1000 mm. (39 3/8 ) outer face inner face 10.5 fixing details: sealing washers shall be installed through a 2-3/8 x 1-9/16
More informationHoesch Arched Roof Installation guide
Table of contents page 1. General........................................................................................ 1 2. Safety hints......................................................................................
More informationInclined Roof System Trimoterm SNV
Inclined Roof System Trimoterm SNV Inclined Roof System Trimoterm SNV - Technical Document EN Version 6 July 2016 TABLE OF CONTENTS 1 Technical Description of Roof System Trimoterm SNV 1 1.1 General 1
More informationTrapezoidal Roof KS1000 RW Installation Guide
Insulated Roof & Wall Panels UK & Republic of Ireland Trapezoidal Roof KS1000 RW Installation Guide Multiple Panels Eaves to Ridge 150mm End Lap September 2018 Trapezoidal Roof KS1000 RW Components Trapezoidal
More informationA Shell construction
A Shell construction A 4/2012 Content 1 BASE AND WALL ANCHORING 1.1 Base with mortar bed 1.2 Base with sill plate 1.3 Base with raised sill plate 1.4 Concrete base (mortar bed) 1.5 Concrete base (sill
More informationSpeedZip. Fixing and Handling Guide
Section 1 Delivery/Storing On Site/Handling l SpeedZip is factory or on-site manufactured. l Straight SpeedZip bundles are a maximum 1 tonne, 2 No. sheets nestled and then and placed face to face, banded
More informationInstallation guide for 20/20
Introduction The following installation instructions are recommended minimum requirements for the 20/20. The designer and fixer should ensure that tiles are installed in accordance with BS 5534; The British
More information900 SERIES WALL PANELS
CI-DS-01-900 CI-PP-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-PJ-03-900 CI-BS-01-900 CI-BS-02-900 CI-BS-03-900 CI-BS-04-900 CI-BS-05-900 CI-OC-01-900 CI-OC-02-900 CI-IC-01-900 CI-FO-01-900 CI-FO-02-900 CI-FO-03-900
More informationDW HORIZONTAL INSTALLATION
AR-PJ-01-DW2H 2" HORIZONTAL PANEL JOINT AR-PJ-02-DW2H 2" VERTICAL PANEL JOINT AR-PJ-03-DW2H 3" HORIZONTAL PANEL JOINT AR-PJ-04-DW2H 3" VERTICAL PANEL JOINT AR-PJ-05-DW2H CUSTOM REVEAL AR-PJ-06-DW2H DW-2000S
More informationCURVED ROOF ASSEMBLY INSTRUCTIONS ATTACHED VERANDAH. Your supplementary guide to building an ATTACHED CURVED ROOF VERANDAH or PATIO BEFORE YOU START
ROOF ATTACHED VERANDAH ASSEMBLY INSTRUCTIONS Your supplementary guide to building an ATTACHED ROOF VERANDAH or PATIO This set of instructions should be used in conjunction with the Stratco instruction
More informationInstallation Procedures
Installation Procedures Nutec Bigsix Roofing sheets properly laid and fixed in accordance with recommendations will provide many years of trouble-free protection from the elements. Failure to follow these
More informationDUTCH GABLE FREESTANDING CARPORT
DUTCH GABLE FREESTANDING CARPORT STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your complete guide to building a FREESTANDING Outback DUTCH GABLE CARPORT BEFORE YOU START Carefully read these instructions. If
More informationREGAL. Installation Manual
REGAL Installation Manual General Information The details shown on the following pages are suggestions or guidelines for installing the Regal system. The installation details shown here are proven methods
More informationINSTALLATION INSTRUCTIONS TRI-ROOF. energy for a better world
energy for a better world INSTALLATION INSTRUCTIONS TRI-ROOF The flexible roof integration system Compatible for framed module types* Simple exchange of modules Replaces existing roofing Special profiles
More information400 SERIES VERTICAL INSTALLATION
CI-DS-01-400V CI-PJ-01-400V CI-PJ-02-400V CI-PJ-03-400V CI-BS-01-400V CI-BS-02-400V CI-BS-03-400V CI-BS-04-400V CI-BS-05-400V CI-OC-01-400V CI-OC-02-400V CI-IC-01-400V CI-IC-02-400V CI-FO-01-400V CI-FO-02-400V
More information900 SERIES PANEL SHEET INDEX STAGGERED ENDLAP STAGGERED MALE LEG AT ENDLAP CONTINUOUS FEMALE ENDLAP INSTALLATION SEQUENCE CI-WR
900 SERIES PANEL CI-DS-01-900 CI-PJ-01-900 CI-PJ-02-900 CI-EL-01-900 CI-EL-02-900 CI-EL-03-900 CI-EL-04-900 CI-EL-05-900 CI-EL-06-900 CI-EL-07-900 CI-EL-08-900 CI-RD-01-900 CI-RD-02-900 CI-RD-03-900 CI-EV-01-900
More informationFinesse Profiles. Nailstrip
Installation Details Profile and Lap Detail 265/465 38mm NAILSTRIP *other widths available CD GRADE PLYWOOD 19mm STRUCTURE SILICONE * MIN 20mm VENTILATION GAP * WHEN ROOF PITCH IS UNDER 7.5 OR TOTAL COMBINED
More information15 YEAR GUARANTEE. Tough and long lasting Guaranteed waterproof for 15 years Economical and easy to fix AVAILABLE IN A RANGE OF COLOURS
INSTALLATION GUIDE AVAILABLE IN A RANGE OF COLOURS 15 YEAR GUARANTEE Tough and long lasting Guaranteed waterproof for 15 years Economical and easy to fix Coroline corrugated bitumen sheet is a tough lightweight
More informationCROSSBAR RAFTER ISOMETRIC
Super Sky Products' typical glazing system consists of glass panels or "lites" which are attached to the main framing members using extruded aluminum "retainers" or "pressure plates". These retainers are
More informationDESIGNER SERIES GUTTER SYSTEM INSTALLATION INSTRUCTIONS
DESIGNER SERIES GUTTER SYSTEM INSTALLATION INSTRUCTIONS GENERAL DESCRIPTION: The Designer Series Gutter System is a specially designed roof edge drainage product for industrial, commercial, and high end
More informationCOMPONENTS OF THE CLICKFAST FASCIA AND GUTTER SYSTEM 5: INTERNAL MITRE
INTRODUCING THE CLICKFAST FASCIA AND GUTTER SYSTEM The Clickfast Fascia and Gutter System was originally designed by Stratco and has proven to be the most successful fascia and gutter system in Australia
More informationDUTCH GABLE CARPORT RECOMMENDED INSTRUCTION MANUAL
DUTCH GABLE CARPORT RECOMMENDED INSTRUCTION MANUAL Table of Contents Introduction 2 Components 3 Step 1a Marking out the Perimeter of the Carport with Footing only 4 Step 2a Footing Set-Out for Concrete
More informationINSTALLATION GUIDE. Outback. Flat Attached BEFORE YOU START ADDITIONAL MATERIALS TOOLS REQUIRED. VERAnDAHS PATIOS CARPORTS
INSTALLATION GUIDE Outback VERAnDAHS PATIOS CARPORTS Flat Attached BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback
More informationINCLINED ROOF SYSTEM TRIMOTERM SNV
INCLINED ROOF SYSTEM TRIMOTERM SNV TABLE OF CONTENTS 1 Technical Description of Roof System Trimoterm SNV 1 1.1 General 1 1.2 Panel Profile 1 1.3 Panel Composition 2 1.4 Technical Data 2 1.4.1 Basic Technical
More informationOUTBACK FLAT ATTACHED VERANDAH PATIO CARPORT - INSTALLATION GUIDE BEFORE YOU START TOOLS REQUIRED ADDITIONAL MATERIALS
BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback Flat Verandah. It is the builder s responsibility to ensure any
More informationTuff-Rib Install Guide
Install Guide bestbuymetalroof.com Page 2 of 27 Page 3 of 27 1. Page 4 2. a. Installation Guide b. Panel Squaring Pages 5, 6 Pages 7, 8 3. Pages 9, 10 4. a. Fascia (optional) b. Eave / 1.5x3.5 Angle c.
More informationKS42 MF SERIES - HORIZONTAL INSTALLATION
CI-DS-01-KSMF H CI-PJ-01-KSMF H CI-PJ-02-KSMF H CI-PJ-03-KSMF H CI-PJ-04-KSMF H CI-PJ-05-KSMF H CI-PJ-06-KSMF H CI-PJ-07-KSMF H CI-PJ-08-KSMF H CI-PJ-09-KSMF H CI-PJ-10-KSMF H CI-PJ-11-KSMF H CI-PJ-12-KSMF
More informationInstallation Guide. Step 3. Valley Flashing. Step 7. Transition Flashings and Accessories. Step 6. Hip and Ridge Installation
Step 7. Transition s and Accessories Step 3. Valley Step 6. Hip and Ridge Installation Step 2. Rake Trim Step 5. Installing the Shingles Step 1. Eave Starter Installation Step 4. Endwall s Installation
More informationSUPREME WALL GARDEN ASSEMBLY INSTRUCTIONS 24/08/16 www.hallsgreenhouses.com Please refer to website for the most up to date instructions. SAFETY WARNING 1. Always wear protective glasses, shoes, gloves
More informationTRADITIONAL GABLE ATTACHED PATIO AND CARPORT. Your complete guide to building an ATTACHED Outback TRADITIONAL GABLE PATIO or CARPORT
TRADITIONAL GABLE ATTACHED PATIO AND CARPORT STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your complete guide to building an ATTACHED Outback TRADITIONAL GABLE PATIO or CARPORT BEFORE YOU START Carefully read
More informationKS SERIES - VERTICAL INSTALLATION
CS-DS-01-KSV CS DISCLAIMER CS-PJ-01-KSV KS42SL EXPANDED PANEL JOINT CS-PJ-02-KSV KS42SL ENGAGED PANEL JOINT CS-PJ-03-KSV KS45SL EXPANDED PANEL JOINT CS-PJ-04-KSV KS45 FLAT ENGAGED PANEL JOINT CS-PJ-05-KSV
More informationGlobal Roofing Solutions Klip-Tite
GRS Klip-Tite Global Roofing Solutions Klip-Tite Talk to us, THE SMART ROOF PEOPLE Visit www.globalroofs.co.za or email info@globalroofs.co.za GRS Klip-Tite Typical specification Materials The roofing
More informationGABLE ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL
GABLE ROOF CARPORT RECOMMENDED INSTRUCTION MANUAL Table of Contents Introduction 2 Components 3 Step 1a Marking out the Perimeter of the Carport with Footing only 3 Step 2a Footing Set-Out for Concrete
More informationOn-roof system Alpha + Product catalogue
On-roof system Alpha + Product catalogue Contents ALPHA +... 3 1. ALPHA + BASE RAILS... 4 2. ALPHA + SPLICES... 5 3. ALPHA + TELESCOPING END PIECES... 6 4. ALPHA + INTER-MODULE CLAMPS AND MODULE END CLAMPS...
More informationHugger Installation. Roof Hugger, LLC P: P.O. Box 1027 F: Odessa, FL
RECEIVING MATERIALS: ROOF HUGGERS are typically placed on wood pallets 3-5 wide and approximately 10 long weighing up to 5,000 lbs. ROOF HUGGERS are shipped via closed van for LTL less than truckload quantities
More informationAWNING / PATIO COVER INSTALLATION INSTRUCTIONS
AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means
More informationTABLE OF CONTENTS A. PBR
TABLE OF CONTENTS A. PBR Panel 1. PBR Panel Architect/Engineer Information....................................... 2 2. PBR Panel UL 90 Requirements............................................... 3 3. PBR
More informationEkoroof LiteTile Dimensions
Ekoroof LiteTile Dimensions 7 3 3.5 Height 40 Width 20 Length Weight per Panel: 3 kg / 6.61 lbs 2 2 Area per panel 800 in / 5.55 ft 2 Panels per Square: 20 (including overlap, for a 100 ft covered area)
More informationSuperFOIL Insulation. Solutions Guide. Pitched Roof - Under Rafter
SuperFOIL Insulation Solutions Guide Pitched Roof - Under Rafter SF19+ Pitched Roof Under Rafter Solutions CONSTRUCTION THICKNESS R -VALUE EXTERNAL SURFACE - 0.040 TILES / SLATES 10mm - BATTEN CAVITY 25mm
More informationInstallation guide. Step-by-step instructions
Installation guide Step-by-step instructions Contents Tools Required to Install p1 Screws & Fixings p2 Injection Moulded Solid Components p3 Components p4 Georgian Hips & Ancillaries p5 Fixing Eaves Beam
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationSLATE & SHINGLE INSTALLATION
EAVE EDGE Apply a small strip of roofing paper to the bottom of eave. Eave flashing is attached to substrate with roofing nails every 9". Install underlayment over entire roof. (See Fig. 1) PAGE 1 Bend
More informationTalk to us, THE SMART ROOF PEOPLE Visit or Global Roofing Solutions Brownbuilt
Talk to us, THE SMART ROOF PEOPLE Visit www.globalroofs.co.za or email info@globalroofs.co.za Global Roofing Solutions Brownbuilt Typical specification Materials The roofing / side cladding shall be Brownbuilt
More informationComponents Catalog. Mounting Systems. Version 18.01, updated: 05/25/2018
Components Catalog Mounting Systems Version 18.01, updated: 05/25/2018 1 Index IBC TopFix 200 Components... 5 Roof Tiles... 6 Roof Hook Alu-Vario S+... 6 Roof Hook Alu-Mammut S+... 6 Roof Hook Alu-Mammut
More informationExtrusions GB-3-IN01. Updated: Scale: REV: - This Drawing is Protected by Copyright Altus NZ Ltd.
Extrusions Updated: N/A Scale: N.T.S REV: - Dwg Dwg Revision Rev No Description Description Date GB-3-IN01 Index Page - - - - - GB-3-001 Extrusions - - - - - GB-3-002 Extrusions - - - - - GB-3-003 Extrusions
More informationMetal Roof Installation Manual. Chapter 14: Fasteners
Metal Roof Installation Manual Chapter 14: Fasteners Chapter 14: Fasteners Chapter Contents 14. Introduction... 14-1 14.1 Fastener Parts and Installation... 14-1 14.1.1 Points... 14-1 14.1.2 Heads... 14-1
More informationFive Star Panel Installation Instructions
Five Star Panel Installation Instructions How to Store Five Star Panels You will need to store FIVE STAR PANELS in dry place to prevent staining, deterioration and possibly void all warranties. Stand the
More informationSheet Steel Facts. Most common head design for self-drilling, self-tapping screws.
Sheet Steel Facts Fastener Guide for Sheet Steel Building Products August, 2003 Fastener Materials Fasteners are manufactured from several materials and coatings. For the purpose of this fact sheet, the
More informationRoof Attachment Overview
Roof Attachment Overview MY STORY Brandon Gwinner Account Executive OUR RACKING SOLUTIONS - Construction and Sales for over 15 years - SunModo brand representative for over 5 years - OSEIA board of Directors
More informationAssembly instructions
Assembly instructions Plannja Profiles 20 105, 20 75, Sinus 18, Sinus 51, 45, 45R, 19R, 35 including flashings and fittings 2017 Roofing Sheet & Wall Cladding TABLE OF CONTENTS Some words of advice...
More informationMULTISPAN GABLE WITH HIP END ATTACHED PATIO
MULTISPAN GABLE WITH HIP END ATTACHED PATIO STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your supplementary guide to building an ATTACHED MULTISPAN GABLE VERANDAH or PATIO WITH HIP END This set of instructions
More informationGIRTS ON BACK OF BUILDING
GIRTS ON BACK OF BUILDING ALL GIRTS ARE 1 1/2 SQUARE TUBE. GIRT LENGTHS FOR 12, 20, 24, AND 30 WIDE BUILDINGS: ON 12 WIDE BUILDINGS GIRTS ARE 67 3/4 LONG ON 20 WIDE BUILDINGS GIRTS ARE 56 3/4 LONG ON 24
More informationCLEARSPAN GABLE STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. WITH GAZEBO END ATTACHED PATIO
CLEARSPAN GABLE WITH GAZEBO END ATTACHED PATIO STRATCO OUTBACK ASSEMBLY INSTRUCTIONS. Your supplementary guide to building an ATTACHED CLEARSPAN GABLE VERANDAH or PATIO WITH GAZEBO END This set of instructions
More informationInstallation Manual. Future Roof Shingle / Slate Products
Installation Manual Future Roof Shingle / Slate Products REVISED 14/09/2010 Future Roof Shingle Installation Manual is a component of Future Roof, Inc. and as such is intended to be used with Future Roof
More informationGuardian warm roof conversion system. Installation Guide
Guardian warm roof conversion system Installation Guide 2 www.guardianroof.co.uk Conservatory walls consist largely of glazed elements including windows and doors that may include structural mullions or
More informationPRODUCT INFORMATION MANUAL SECTION: 16 FIXED METAL AWNINGS FIXED METAL AWNINGS
FIXED METAL AWNINGS Fixed Metal Awnings BAHAMA Maximum Width Minimum Width Minimum projection Minimum Drop TS - Truss Support Maximum Overhang Minimum Overhang Unlimited 500mm TS=1601mm PS=2847mm PS=
More informationPINEHAVEN SHEDS Assembly Instructions FOR LEAN-TO SHEDS
PINEHAVEN SHEDS Assembly Instructions FOR LEAN-TO SHEDS GARDEN PRODUCTS www.pinehavensheds.co.nz 5/16 hex drive bit, By asking about our products at your nearest DIY or gardening store www.pinehavensheds.co.nz
More informationSPRINGLOK SPRINGLOK FLASHING SYSTEM PRODUCT BROCHURE ENGINEERED PRODUCT SYSTEMS
FLASHING SYSTEM ENGINEERED PRODUCT SYSTEMS PRODUCT BROCHURE 2 ND EDITION FLASHING SYSTEM FUNCTIONALLY UNIQUE. ENGINEERED PRODUCT SYSTEMS / FLASHING Fry Reglet comprehensive selection of moisture prevention
More informationINSTALLATION GUIDE. Outback Clearspan Gable BEFORE YOU START ADDITIONAL MATERIALS ADDITIONAL MATERIALS WITH COOLDEK ROOFING
INSTALLATION GUIDE Outback Clearspan Gable WITH COOLDEK ROOFING BEFORE YOU START It is important to check your Local Government Authority requirements before the installation of your new Stratco Outback
More informationTable of Contents. Notes to Designer/User Map of Typical Roof Conditions Fastener Placement Fastener Selection...
Table of Contents Section Page Notes to Designer/User... 2-3 Map of Typical Roof Conditions... 4 Fastener Placement... 5 Fastener Selection... 6 Ridge/Hip Flashing... 7 Valley Flashing... 8 Eave Flashings...
More informationGlobal Roofing Solutions Klip-Lok 406 Aluminium
GRS Klip-Lok 406 Global Roofing Solutions Klip-Lok 406 Aluminium www.globalroofs.co.za marketing@globalroofs.co.za GRS Klip-Lok 406 GRS Klip-Lok 406 Alum. 09/18 Typical Specification Materials The roofing
More informationStratco Sanctuary INSTALLATION BEFORE YOU START TOOLS REQUIRED GUIDE
INSTALLATION GUIDE Stratco Sanctuary Verandahs, Patios and Carports BEFORE YOU START It is important to check with your Local Government Authority prior to the installation of your new Stratco Sanctuary
More informationSecuAnch Roof Anchor System
Height Safety Products Email: marketing@fallprotec.com SecuAnch Roof Anchor System 1 Presentation The SecuAnch lifeline is designed to be permanently installed on buildings and other structures where maintenance
More informationSteel Roofing & Siding INSTALLATION GUIDE
Steel Roofing & Siding INSTALLATION GUIDE Your Authorized Dealer is: WASHINGTON Auburn (800) 700-7228 WASHINGTON Spokane (866) 321-5954 www.nuraymetals.com CALIFORNIA Redlands (800) 806-8729 CONTENTS BEFORE
More informationThe Roofing Store TRS 9 35MM 78MM 150MM 78MM PRODUCT TECHNICAL DATA
TRS 9 35MM 78MM 150MM 78MM THICKNESS END SPAN INTERNAL SPAN MINIMUM PITCH 0.55MM 2.30M 3.20M 3 DESCRIPTION TRS 9 profile is designed for commercial and industrial roofing. The profile is suitable for low
More informationinstallation guide Villa
installation guide Villa Table of Contents Introduction............................. 2 Safety................................... 2 Tools.................................... 2 Codes & Requirements....................
More informationInstallation Manual. Last Updated 4 February, Postal PO Box 932 Bayswater VIC
Installation Manual Last Updated 4 February, 2013 Part 1: Provided Material The Panel Expandable Foam Sealing Strip Barge Capping Z-Fascia Structural Screws Timber: 3/8 head size Metal: 5/16 head size
More informationDesign & Install Guide. The New Standard for Commercial Roof Laps. End-Lap Solution for Insulated Panel Roofing AS WEATHER RESISTANCE
End-Lap Solution for Insulated Panel Roofing AS4046.9 WEATHER RESISTANCE The New Standard for Commercial Roof Laps SecureLap provides a solution to the troublesome sheet to sheet endlap and offers a real
More informationENGINEERING STRENGTH INSTAL L AT I O N M A NUAL OUR STRENGTH IS OUR STRENGTH
ENGINEERING STRENGTH INSTAL L AT I O N M A NUAL OUR STRENGTH IS OUR STRENGTH RAFTER PREPERATION RAFTER PREPARATION A FRAME PREPERATION AND ASSEMBLY A FRAME PREPARATION AND ASSEMBLY... Open boxes, remove
More informationtechnical bulletin Roofline Installation Details No.7 Fascia Installation Details Typical Eaves Details K16 Fascia & 9mm Vented Soffit
Roofline Installation Details This is intended to provide you with a brief overview of the popular products in Kestrel s Roofline range, where they can be used and the main criteria for installation. Typical
More informationTable of Contents Light Gauge Metal Roof & Wall Panels
Table of Contents Light Gauge Metal Roof & Wall Panels Installation Guide for Delta Rib, Nor-Clad, Strata Rib & 2-1/2 Corrugated Introduction Important Notice Notes: April 2008 Minimum Recommended Tools
More information3/ /
SUNGLAZE system is designed for both rafter and purlin construction options. Recommended minimum roof slope for Sunglaze applications is 5 o. Where lower slopes are necessary, we recommend rafter construction.
More informationNEW equinox INSTALLATION GUIDE Issue
NEW equinox INSTALLATION GUIDE Issue 1 CONTENTS If in doubt at any stage 1. Preparing the ring beam 2 2. Installing the framework 3 3. Insulation and waterproofing 7 4. Tile application: Steel tiles 9
More informationDESIGN GUIDE Topdek 7 00
Topdek 700 DESIGN GUIDE Innovative, stylish, strong and flexible, Topdek 700 is an exceptional cladding. FORM AND FUNCTION Utilising an ingenious concealed clip, Topdek 700 benefits from a strong, clean
More informationRoof fastener. Perfectly thought out for every roof
Roof fastener Perfectly thought out for every roof 1 Welcome to the world of clever solutions Solutions for every roof In our production areas we produce all needed components for the sub construction
More informationHILAND TRAY FORM AND FUNCTION MATERIAL SPECIFICATIONS DESIGN GUIDE ROOFING I WALLING
HILAND TRAY ROOFING I WALLING DESIGN GUIDE FORM AND FUNCTION Hiland Tray is a modern 455mm wide tray roofing and walling system, roll formed onsite with a mobile roll forming facility in long single lengths
More informationALL SEASON PATIO COVER
ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the
More informationKlip-Lok 406 Aluminium
Klip-Lok 406 Alumin GRS Klip-Lok 406 Global Roofing Solutions TM Klip-Lok 406 Aluminium Talk to THE SMART ROOF PEOPLE Visit www.globalroofs.co.za or email info@globalroofs.co.za GRS Klip-Lok 406 GRS Klip-Lok
More informationInstallation manual for sloped roof assembly system. Jurchen Technology GmbH Prinz-Ludwig-Straße Helmstadt
Installation manual for sloped Jurchen Technology GmbH Prinz-Ludwig-Straße 5 9764 Helmstadt Index. Security note.... Hazard note.... Planning and installation notes.... Installation notes... 4. Outline
More informationALPINE TRAY. To get the best from this product please follow these recommendations.
F I X I N G D E TA I L S ALPINE TRAY The standing seam roofing profile is designed to withstand some of New Zealand s harshest weather in our toughest environments. To get the best from this product please
More informationNutec Bigsix Roofing Accessories
Nutec Bigsix Roofing Accessories Nutec Bigsix Close Fitting Adjustable Ridge Capping (Grey) Adjustable for 0º - 0º pitches 70-000 87 mm 70-00 87 mm Nutec Bigsix Close Fitting Adjustable Ridge Capping (Terracotta)
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationINSTALLATION INSTRUCTIONS LS X 12-2 X 7 1/2 FRAME LOAFING SHED
INSTALLATION INSTRUCTIONS LS-12 12 X 12-2 X 7 1/2 FRAME ACTUAL FRAME BASE SIZE: 12 X 12-2 LOAFING SHED Our unique assembly process quickly transforms the individual pieces into a finished structure that
More informationDW VERTICAL INSTALLATION
AR-PJ-01-DW5V AR-PJ-02-DW5V AR-PJ-03-DW5V AR-PJ-04-DW5V AR-BS-01-DW5V AR-BS-02-DW5V AR-OC-01-DW5V AR-OC-02-DW5V AR-OC-03-DW5V AR-IC-01-DW5V AR-IC-02-DW5V AR-IC-03-DW5V AR-FO-01-DW5V AR-FO-02-DW5V AR-FO-03-DW5V
More informationFastening Systems L.P. 12/11/2013 EJOT Fastening Systems L.P. 1
Fastening Systems L.P. 12/11/2013 EJOT Fastening Systems L.P. 1 Solar Fastening Systems 12/11/2013 EJOT Fastening Systems L.P. 2 What has to be considered? - The installation of a solar system increases
More informationInstallation Manual. Future Shingle Products
Installation Manual Future Shingle Products TITLE REVISED 7/4/2011 Future Shingle Installation Manual is a component of Future Roof, Inc. and as such is intended to be used with Future Roof products only.
More informationDETAIL MANUAL for Standing Seam / Image II
DETAIL MANUAL for Standing Seam / Image II Best Buy Metals Toll Free 1-800-728-4010 / Phone 423-479-6382 / Fax 423-728-3066 www.bestbuymetals.com Best Buy Metals Standing Seam Roofing Panels Fig. 2 Standing
More informationTuff-Rib. Installation Manual. Nationwide supplier of quality metal roofing. Toll-Free (800) S. Lee Hwy. Cleveland, TN 37311
Installation Manual Nationwide supplier of quality metal roofing. 65 S. Lee Hwy. Cleveland, TN 7.. www.bestbuymetals.com Toll-Free (800) 78-00 IMPORTANT NOTICE This manual contains suggestions and guidelines
More informationlindab we simplify construction LindabSandwichPanels Installation instructions PIR Panels
lindab we simplify construction LindabSandwichPanels Installation instructions PIR Panels Assembly instructions Before you start Check that the panel support structures are level. Position the packages
More informationVENTED GABLE DETAIL ROOF PANEL GABLE FLASHING 24" C/C MAX. BUTYL SEALANT TAPE ROOF PURLIN FLASH AB-1, AB-2, AB-3, OR AB-4
ROOF PANEL GABLE FLASHING FASTENER @ 24" C/C MAX. ROOF PURLIN BUTYL SEALANT TAPE FLASH AB-1, AB-2, AB-3, OR AB-4 FASTENER @ EVERY MAJOR RIB OR 12" C/C MAX. F-J TRIM FABRAL ALUMINUM SOFFIT FASTENER 24"
More informationPRICE LIST - 6th February 2017
W: www.cladco.co.uk E: info@cladco.co.uk T: 01837 659901 F: 01837 659902 Cladco Profiles North Road Industrial Estate, North Road, Okehampton, Devon, EX20 1BQ. PRICE LIST - 6th February 2017 Colour coated
More informationBalConIEs.
BalConIEs Installation guidelines for balustrade cladding The following regulations and provisions must be observed when preparing and installing balustrade cladding using Trespa Meteon sheets: 防 The applicable
More information