SITELINE CLAD-WOOD WINDOW CASEMENT TABLE OF CONTENTS

Transcription

1 TABLE OF CONTENTS 1

2 GENERAL INFORMATION Dimensional Windows Siteline clad casement windows may be specified as "dimensional", by adjusting the desired rough opening width or height. Siteline clad casement windows are available with left or right hand operation, or stationary (non-venting). Operating mechanism includes corrosion resistant steel hinges and dual arm roto-type operator with hardened steel gears and operating arms. Sash locks are concealed unison type with an exposed locking lever and escutcheon plate. There are several interior hardware finish options. Refer to the Specifications for finish options. Multiple Assemblies Siteline clad casement windows may be mulled above, below, or beside other clad casement windows, or other clad window products. Scale: NTS 2

3 LITE CUT INFORMATION Lite Cut Options Special lite cut patterns can include a wide variety of straight line and radius patterns. The illustrations shown here represent just a few of the possibilities. Rectangular, horizontal, vertical and Prairie lite patterns are available in all standard size clad casement windows. Uneven, diamond, radius and Gothic lite cuts are available, subject to approval. Approvals are based on the ability to fulfill the design requirement while maintaining the construction integrity of the finished product. SITELINE Siteline clad casement windows are available with removable grilles in 7/8", 1-1/8" and 1- widths, Airspace (between the panes) grilles, and Simulated Divided Lites. Standard lite cuts are rectangular, and conform to the layouts noted in the charts on the next page. To use the chart, refer to the appropriate table by the type of window and type of bars or grilles the section drawings illustrate. Then simply cross reference the frame Height and Width to determine the standard lite cut. Rectangular Horizontal Prairie Uneven Diamond Radius Gothic Bar Alignment Alignment of divided lite muntin bars from one window to the next is often required by fine architectural design. Wood grilles, Grilles Between the Glass, grilles, and Simulated Divided Lites may be specified with muntin bars aligned. Scale: NTS 3

4 HANDING & OPERATION Left Hand Right Hand Operator Operator Casement Unit Handing: Unit Handing is defined (from the EXTERIOR) as the direction the sash opens. Scale: NTS 4

5 UNIT SIZING, ROUGH OPENING & MASONRY OPENINGS General Notes: Unit size is always the maximum size of the window with or without trim and does not include nail fin. Horizontal exterior trim offerings below are the same with or without sill nose. Masonry Opening: Masonry opening is always 1/2" over (height and width) the unit size or the outside of the trim of the window. : Rough opening is always 3/4" over frame size of the window. A (BM) B (BBM) C (AC) D (FC) Vertical exterior trim offerings without sill nose. Trim on all 4 sides. Vertical exterior trim offerings with standard sill nosing. Trim on 3 sides. H (FC) G (AC) F (BBM) E (BM) L (FC) K (AC) J (BBM) I (BM) Scale: NTS 5

6 TRIM OPTIONS 1 1/2" 1 5/16" 1 1 1/2" 1 1/2" Standard Brickmould Beaded Brickmould 1 5/16" 1 3/4" 3" 3" 3 1/2" Flat Casing Adams Casing Sill Nose Options 9/16" No Sill Nose 5/16" 1 3/4" Standard Sill Nose 1/2" 1" 1 1/16" 1 3/4" 1" Sill Nosing 2 1/4" 2" Sill Nosing Scale: 3" = 1' - 0" 6

7 GLASS STOP OPTIONS Trasitional Contemporary Scale: NTS 7

8 JAMB EXTENDER OPTIONS 1 5/32" TYP 1 6 9/16" /4" Wall 6 9/16" Wall 7 Wall 5/16" 4 1/16" 4 3/4" 7 1/4" 9 5/16" 1 5/4 Jamb Thickness Option 7 1/4" Wall 9 5/16" Wall 5/4-4/4 Stacked Kerfed Jamb Option Kerfed Jamb Extension only available on 4/4 or 5/4 options Maximum jamb length for 4/4 is 7. Maximum jamb length for 5/4 is 7 1/4". Maximum jamb length for 5/4 2 piece stacked is 12". Scale: 3" = 1' - 0" 8

9 MULLION OPTIONS - STANDARD 5 2 5/16" 5 2 5/16" Operating - Operating Operating - Stationary 2 5/16" 5 2 5/16" 4 3/4" Stationary Operating Direct Set Operating 4 3/4" 2 5/16" Direct Set - Operating Scale: NTS 9

10 MULLION OPTIONS - SPREAD 6 1/8" 1/4" Operating / Operating w/ 1/4" Structural Mull Horizontal Section 6 1" 7 2" Operating / Operating w/ 1" Solid Spread Mull Horizontal Section Operating / Operating w/ 2" Solid Spread Mull Horizontal Section 9 4" Operating / Operating w/ 4" Solid Spread Mull Horizontal Section Scale: NTS 10

11 MULLION OPTIONS - SPREAD 1/4" 6 3/16" 1" 6 7/8" Stationary Operating w/ 1/4" Structural Mull Vertical Section Stationary Operating w/ 1" Solid Spread Mull Vertical Section 4" 9 7/8" 2" 7 7/8" Stationary Operating w/ 2" Solid Spread Mull Vertical Section Stationary Operating w/ 4" Solid Spread Mull Vertical Section Scale: NTS 11

12 DIVIDED LITE OPTIONS 7/8" 1 2 5/16" 7/8" Bead SDL Bead SDL 1 Bead SDL 2 5/16" Bead SDL 11/16" 1" GBG 23/32" Contour GBG 1" Contour GBG 7/8" 1 Full Surround 7/8" Wood Grille Full Surround Wood Grille Full Surround 1 Wood Grille Scale: 3" = 1' - 0" 12

13 DIVIDED LITE OPTIONS 7/8" 1 2 5/16" Putty / Bead 7/8" Putty / Bead Putty / Bead 1 Putty / Bead 2 5/16" Putty / Bead 7/8" 1 2 5/16" Putty / Putty 7/8" Putty / Putty Putty / Putty 1 Putty / Putty 2 5/16" Putty / Putty 7/8" 1 2 5/16" Bead / Putty 7/8" Bead / Putty Bead / Putty 1 Bead / Putty 2 5/16" Bead / Putty Scale: 3" = 1' - 0" 13

14 MIN-MAX SIZING - OPERATOR 84" 18" 18" Minimum Configuration 36" Maximum Configuration Note: Limited operation configurations w/ 20 degree opening sash limiter: [32" x 84"] [36" x 78"] [36" x 84"] Scale: NTS 14

15 MIN-MAX SIZING - PICTURE 84" 12" 18" Minimum Configuration 84" Maximum Configuration Scale: NTS 15

16 OPERATING - VERTICAL SECTION 1 Sash Size Screen Size Frame Size 2 9/16" Scale: 6" = 1' - 0" 16

17 OPERATING - HORIZONTAL SECTION Frame Size 1 1 Daylight Opening Sash Size Scale: 6" = 1' - 0" 17

18 OPERATING IMPACT - VERTICAL SECTION 1 Sash Size Daylight Opening Screen Size Frame Size 2 9/16" Scale: 6" = 1' - 0" 18

19 OPERATING IMPACT - HORIZONTAL SECTION Frame Size 1 Screen Size 1 Daylight Opening Sash Size Scale: 6" = 1' - 0" 19

20 FIXED - VERTICAL SECTION Sash Size Daylight Opening Frame Size Scale: 6" = 1' - 0" 20

21 FIXED - HORIZONTAL SECTION Frame Size Daylight Opening Sash Size Scale: 6" = 1' - 0" 21

22 FIXED IMPACT - VERTICAL SECTION Sash Size Daylight Opening Frame Size Scale: 6" = 1' - 0" 22

23 FIXED IMPACT - HORIZONTAL SECTION Frame Size Daylight Opening Sash Size Scale: 6" = 1' - 0" 23

24 PUSHOUT - VERTICAL SECTION 1 3/16" 1 9/16" Sash Size Daylight Opening Screen Size Frame Size 1 Scale: 6" = 1' - 0" 24

25 PUSHOUT - HORIZONTAL SECTION Frame Size 1 9/16" Screen Size 1 9/16" Daylight Opening Sash Size Scale: 6" = 1' - 0" 25

26 PUSHOUT FIXED - VERTICAL SECTION Sash Size Daylight Opening Frame Size Scale: 6" = 1' - 0" 26

27 PUSHOUT FIXED - HORIZONTAL SECTION Frame Size Daylight Opening Sash Size Scale: 6" = 1' - 0" 27

28 RADIUS TOP - VERTICAL SECTION Sash Size Daylight Opening Frame Size Scale: 6" = 1' - 0" 28

29 DIRECT SET SEGMENT HEAD - VERTICAL SECTION 1 13/16" 1/2" Daylight Opening Frame Size 1 13/16" 1 3/16" Scale: 6" = 1' - 0" 29

30 BAY & BOW - VERTICAL SECTION HEAD BOARD 3/4" Frame Size SEAT BOARD 3/4" Scale: NTS 30

31 30 BAY - HORIZONTAL SECTION Frame Size Scale: NTS 31

32 45 BAY - HORIZONTAL SECTION Frame Size Scale: NTS 32

33 BOW 3 WIDE - HORIZONTAL SECTION Frame Size Scale: NTS 33

34 BOW 4 WIDE - HORIZONTAL SECTION Frame Size Scale: NTS 34

35 BOW 5 WIDE - HORIZONTAL SECTION Frame Size Scale: NTS 35

36 BOW 6 WIDE - HORIZONTAL SECTION Frame Size Scale: NTS 36