HAND AND POWER TOOLS
|
|
|
- Warren Owen
- 6 years ago
- Views:
Transcription
1 HAND AND POWER TOOLS Steingass Mechanical Contracting, Inc. 754 Progress Drive Medina, Ohio (330)
2 HAND AND POWER TOOLS General All power tools whether furnished by Steingass Mechanical Contracting, Inc. or by the employee shall be maintained in a safe condition. Steingass Mechanical Contracting, Inc. shall have the right to remove from service any tool it deems defective, damaged, or that is not in compliance with its applicable requirements or standards. It shall be identified as unsafe by tagging or locking the controls to render inoperable until it can be removed from the worksite. Maintenance Hand tools and power tools shall be inspected prior to use and maintained in a safe operating condition and used only for the purpose for which they were designed. Damaged and defective tools shall be tagged Do Not Use, repaired, replaced or removed from service. Any tool removed from service shall be inspected for verification of repair prior to returning it to service. Storage Tools shall not be left on scaffolds or elevated workspaces, and containers shall be provided for hand tools at the job site. Guarding Tools designed to accommodate guards shall only be operated with such guards in place. Guards will be operable at all times and may not be manipulated in such a way that will compromise its integrity or compromise the protection in which it was intended. Guarding shall meet requirements set forth in ANSI B15. Belts, gears, pulleys, sprockets, spindles, drums, and other type moving drives shall be guarded. 2
3 Grounding Electric-powered tools shall be the double-insulated type or effectively grounded. Switches On-off switches controlling the operation of hand-held powered tools shall conform to the following: Hand-held powered sanders and grinders with 2-inch or less diameter wheels may be equipped with only a positive on-off switch. Hand-held powered drills, tappers, fasteners drivers, horizontal, vertical, and angle grinders with wheels exceeding 2 inches in diameter, disk sanders, belt sanders, reciprocating saws, and similar tools shall be equipped with a momentary contact on-off control. They may have a lock-on control provided a single motion of the same finger(s) that turn it on can shut off the power. Jackhammers, and similar pneumatic-powered tools, except concrete vibrators, shall be equipped with a constant pressure switch that shuts off power when pressure is released. Personal Protective Equipment (PPE) Hand tool and power tool operators shall be provided with and use respective types of PPE as set forth in the applicable OSHA standards and/or Steingass Mechanical Contracting, Inc. Personal Protective Equipment Policy. Employees using hand and power tools that are exposed to the hazard of falling, flying, abrasive and splashing objects or exposed to harmful dust, fumes, mist vapors and/or gases shall be provided with particular PPE necessary to protect them from the hazard. 3
4 Hazardous Conditions Only non-sparking tools shall be used in locations where sources of ignition may cause an explosion or fire. Gasoline powered tools shall not be used underground or in locations where toxic exhaust gases can accumulate. Impact tools including drift pins, wedges, and chisels shall be kept in a dressed condition or equipped with nonmushrooming heads. Employees shall not work under areas where handheld tools are being used unless the tools are equipped with restraining straps, or appropriate decking or planking is provided for employee protection. Pneumatic Impact Tools Pneumatic tools shall be operated with safety clips or retainers installed to prevent tools from being accidentally discharged from the chuck. Air Hoses All connections, couplings, and splices in air lines exceeding 0.5 inch inside diameter shall be equipped with clips, and wire rope or chain lashings. The clips and lashings shall be installed in a manner that prevents whipping of the loose line should that connection coupling or splice fail. 4
5 Compressed Air Compressed air shall not be directed at any part of the body and shall not be used for cleaning purposes except when reduced to less than 30 psi and the operator protected by PPE as set forth in the applicable OSHA standard. Nailers Pneumatically driven nailers, staplers, and similar equipment provided with automatic fasteners feed, which operate at more than 100 psi shall have a safety device on the muzzle to prevent the ejection of the fasteners unless the muzzle is in contact with the work surface. Grinding Tools Grinding tools shall not be used without the proper guards, protective flanges, and tool rests installed and maintained in proper adjustment. Abrasive Wheels Abrasive wheels and scratch brushes shall not be operated in excess of their rated safe speed. Cracked or defective abrasive wheels shall be removed from service immediately. Ring tests should be performed as recommended by the manufacturer. 5
6 Switches Switches shall be located to enable the operator to cut off the power without leaving his operating position. Fixed power driven tools shall be provided with a disconnect switch that can be locked in the off position. Automatic Feed Whenever the nature of the work will permit, automatic feed devices shall be installed on fixed power driven woodworking tools. Feeder attachments shall have the feed rolls and/or other moving parts guarded to protect the operator. Push Sticks A push stick, or similar safe means shall be used for all operations close to high-speed cutting edges. Planers and Joiners Planers and joiners shall be equipped with cylindrical cutting heads and fully guarded. Bandsaws Bandsaw blades shall be fully enclosed except at the point of operation. 6
7 Cleanup Work areas shall be kept clean and a brush provided to remove sawdust, chips, and shavings. Circular Saws Bench type circular saws shall be equipped with spreaders, anti-kickback devices, and guards that automatically enclose the exposed cutting edges. Portable handheld circular saws shall be equipped with guards above and below the base plate. Power saws shall not be left running unattended. Portable power saws shall be unplugged from their power source when unattended. Hydraulic Powered Tools The manufacturers safe operating pressure for hoses, valves, pipes, filters, and fittings shall not be exceeded. Powder-Actuated Tools Powder-actuated tools shall be operated and serviced only by persons who have been trained and certified in the safe use of such tools. Operators must possess and operator s card issued by a firm or person authorized to issue such cards, usually the equipment manufacturer or sales representative. Flammable Atmospheres Powder-actuated tools shall not be used in explosive or flammable atmospheres. 7
8 Studs and Fasteners Only powder charges, studs, or fasteners specified by the manufacturer for the specific tool shall be used. Power Loads Cased and caseless power loads shall be coded to identify power load levels by case color. In the event of a misfire, the operator shall hold the tool firmly against the work surface for a period of 30 seconds and then follow the instructions set forth in the manufacturers instructional manual. Materials Driving into soft or easily penetrated material is prohibited unless the material is backed to prevent complete penetration. Tools shall not be used on very hard or brittle materials such as cast iron, glazed tile, and surfaced hardened steel, glass block, face brick, or hollow tile. Use Tools shall not be loaded until just prior to firing. Loaded tools shall not be left unattended, pointed at any person, and all parts of the body shall be kept clear of the muzzle. Storage Powder-actuated tools and power loads shall be locked in a container and stored in a safe place when not in use and shall be accessible only by authorized persons. 8
9 General Inspection Form This form is used to document inspections of rigging equipment, ladders and harnesses. Item Inspected # Inspected # OK # Defective # O/S # Repaired Example: Wire rope chokers Nylon Slings Safety Harnesses Ladders Location: Month & Color Code: Date of Inspection: Next Inspection Date: Inspector Name and Title: 9
Portable Hand and Power Tools Self-Inspection Checklist
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Portable Hand and Power Tools Self-Inspection Checklist Guidelines: This checklist covers
Tools Hand and Power. OSHA Office of Training and Education 1
Tools Hand and Power 1 Hazards Workers using hand and power tools may be exposed to these hazards: objects that fall, fly, are abrasive, or splash harmful dusts, fumes, mists, vapors, and gases frayed
Health & Safety Policy and Procedures Manual SECTION 5 HAND AND POWER TOOLS
SECTION 5 HAND AND POWER TOOLS 1. POWER TOOLS A. References: 29 CFR 1926 Sub Part I (300-307) B. Employees using hand and power tools and exposed to the hazard of falling, flying, abrasive, and splashing
College of Forestry 610: Power Tools
College of Forestry 610: Power Tools Safety Policy & Procedure Manual Section 600: Workshops and Shop Tools Effective: 01 January 2007 Revised: August 2014 PURPOSE The purpose of this section is to provide
SAFETY DIRECTIVE 2.0 DEPARTMENTS AFFECTED. This Administrative Directive shall apply to all Town of Marana departments and employees.
SAFETY DIRECTIVE Title: Hand and Power Tools Issuing Department: Town Manager s Safety Office Effective Date: July 1, 2014 Approved: Gilbert Davidson, Town Manager Type of Action: New 1.0 PURPOSE This
Chapter 8 Workshops and Maintenance
Chapter 8 Workshops and Maintenance General 1. Eye protection shall be worn at all times when operating power equipment and tools. 2. Report all equipment defects immediately. Do not use unsafe equipment
(a) Machine Construction General (a) 4/5/2016
1910.213 WOODWORKING MACHINERY REQUIREMENTS 1910.213(a) Machine Construction General Machines shall be constructed to be free from vibration when largest tool is mounted and run at full speed 1910.213(a)
Effective Date: 10-January Table of Contents
Version: 4 Page: 1 of 9 Table of Contents 1.0 Introduction... 2 1.1 Purpose... 2 1.2 Scope... 2 1.3 Definitions... 2 1.4 Responsibilities... 2 Environmental Health and Safety Office (EHSO)... 2 Directors,
Hand and Power Tool Safety
Hand and Power Tool Safety 2 Continuing Education Hours Wisconsin Contractors Institute N27 W23953 Paul Road, Suite 203 Pewaukee, WI 53072 www.wicontractorsinstitute.com 262-409-4282 What is the Purpose
Each employer shall be responsible for the safe condition of tools and equipment used by employees, including tools and equipment which may be
For General Industry 1910 Subpart P, Hand and Portable Power Tools and Other Hand-Held Equipment. 1910.241, Definitions. 1910.242, Hand and portable powered tools and equipment, general. 1910.243, Guarding
Module Overview. Hand and Power Tool Safety Module covers:
Module Overview Hand and Power Tool Safety Module covers: Various hazards, basic safety procedures and safeguards associated with hand and portable power tools. Training information presented should not
Hand and Power Tool Safety Program
1. Purpose: Virginia Commonwealth University Department of Safety and Risk Management (SRM) has developed this Program to ensure the safety of employees working with hand and portable powered tools and
Woodworking Machinery- Other than Saws Self-Inspection Checklist
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Woodworking Machinery- Other than Saws Self-Inspection Checklist Guidelines: This checklist
Hand and Portable Power Tools Program
Hand and Portable Power Tools Program Copyright 2017 President and Fellows of Harvard University Revised September 21, 2017 Harvard University Department of Environmental Health & Safety 46 Blackstone
DEPARTMENT OF LICENSING AND REGULATORY AFFAIRS DIRECTOR'S OFFICE GENERAL INDUSTRY SAFETY STANDARDS PART 38. HAND AND PORTABLE POWERED TOOLS
DEPARTMENT OF LICENSING AND REGULATORY AFFAIRS DIRECTOR'S OFFICE GENERAL INDUSTRY SAFETY STANDARDS (By authority conferred on the director of the department of licensing and regulatory affairs by sections
My Background. Session Topics. General Industry Standards. Variety of Tools Covered. Related Standards/Hazards 1/27/2014
My Background Shop Safety: Equipment and Tools Mary Bauer UW Extension Webinar January 28, 2014 Mary Bauer CIH, CSP Compliance Assistance Specialist Eau Claire, WI 54701 715-832-9019 28 years w/ OSHA 20
This review. prepares the student for nationally industry recognized assessments. A general overview of power tools is provided.
This review prepares the student for nationally industry recognized assessments. A general overview of power tools is provided. Please follow the specific instructions provided by the manufacturer. PREREQUISITE:
Environmental Health and Safety Department
Machine Guard Handout Bench Grinder Adjust tongue to ¼ inch from blade Adjust work rest to 1/8 inch from the blade Because the safety guard is designed to restrain the pieces of a shattered grinding wheel,
Agricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
NC Employees Workplace Program Requirements for Safety and Health. Machine Guarding
Scope Machine Guarding A wide variety of mechanical motions and actions on machines may present hazards to employees. These can include movement of rotating members, reciprocating arms, moving belts, meshing
STUDENT/FACULTY MACHINE SHOP SAFETY RULES
STUDENT/FACULTY MACHINE SHOP SAFETY RULES Supervisors have full authority over the shop and its safe use, including the responsibility, authority, and obligation to prohibit shop or tool access for the
Guild of Oregon Woodworkers Shop Safety Test
Guild of Oregon Woodworkers Shop Safety Test You must pass the Test with an 80% or better and self-correct it to 100% Make sure you put the answers under the correct portion of the answer sheet for the
North Dakota State University Power Tool Operations and Maintenance
North Dakota State University Power Tool Operations and Maintenance I. Introduction This NDSU procedure provides guidelines for the use of power tools. The intent is to establish proper safety procedures
C-1650P 16 Gauge, 1/2 Medium Crown Stapler
C-1650P 16 Gauge, 1/2 Medium Crown Stapler MANUAL/WARNING: IMPORTANT PLEASE READ BEFORE USING TOOL Please read the following operating instructions manual. Refer to this manual for safety, adjustment and
Tech Ed Lab Safety SAFETY RULES Page 1-1
SAFETY RULES Safety Rules for Working with Wood 1. Secure your instructor s approval for all work you do in the shop. 2. Wear safety glasses when doing any operation that may endanger your eyes. 3. Always
SAFETY INFORMATION PACKET
WILLOWCREEK MIDDLE SCHOOL SAFETY INFORMATION PACKET GENERAL SHOP SAFETY 1 WIDE BELT SANDER 2 BAND SAW 3 MITER SAW 4 UP- CUT SAW 4 PLANER 6 TABLE SAW 7 DRILL PRESS 8 LATHE 8 DISK / VERTICAL BELT SANDER
C-W1650S 16 Ga, 1 Wide Crown Stapler
C-W1650S 16 Ga, 1 Wide Crown Stapler MANUAL/WARNING: IMPORTANT PLEASE READ BEFORE USING TOOL Please read the following operating instructions manual. Refer to this manual for safety, adjustment and trouble
C-1116LMA - Automatic Stapler w/ Long Mag
C-1116LMA - Automatic Stapler w/ Long Mag MANUAL/WARNING: IMPORTANT PLEASE READ BEFORE USING TOOL Please read the following operating instructions manual. Refer to this manual for safety, adjustment and
DEPARTMENT OF LICENSING AND REGULATORY AFFAIRS DIRECTOR'S OFFICE CONSTRUCTION SAFETY STANDARDS
DEPARTMENT OF LICENSING AND REGULATORY AFFAIRS DIRECTOR'S OFFICE CONSTRUCTION SAFETY STANDARDS (By authority conferred on the director of the department of licensing and regulatory affairs by sections
WORKSHOP SAFETY POLICIES
WORKSHOP SAFETY POLICIES 1 TABLE OF CONTENTS Scope 3 Responsibilities 3 General Safety Guidelines 4 Machine Safety 6 Drill Press 6 Boring Mill 6 Grinder 7 Lathe 8 Milling Machine 9 Band Saw 10 Horizontal
BB Inch Double Cut Saw Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.
BB07552 5 Inch Double Cut Saw Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. This manual provides important information on proper operation & maintenance.
Portable circular saw Used to cut a wide range of construction materials Check the cord, leads and 3 pin plugs for any damage. A Residual Current Device (RCD) is plugged into the power source. Do not stand
NAILER / STAPLER IMPORTANT IMPORTANT IMPORTANT IMPROPER AND UNSAFE USE OF THIS NAILER WILL RESULT IN DEATH
NAILER / STAPLER ORIGINAL LANGUAGE USER MANUAL Safety / O Operation Maintenance / Troubleshooting IMPORTANT IMPORTANT IMPROPER AND UNSAFE USE OF THIS NAILER WILL RESULT IN DEATH IMPROPER AND UNSAFE USE
CHAPTER 52 ELECTRICAL POWER TOOLS
CHAPTER 52 ELECTRICAL POWER TOOLS HOW TO CHOOSE AND USE THEM The Types and Uses pages provide you with a list of the electrical power tools found in the pioneer tool outfit. These pages should help you
Circular Saw MODEL MT581. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH Circular Saw MODEL MT58 005337 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Occupational Safety, Health and Welfare (Woodworking Machines) Regulations 1989
Occupational Safety, Health and Welfare (Woodworking Machines) Regulations 1989 GN 66/1989 THE OCCUPATIONAL SAFETY, HEALTH AND WELFARE ACT 1988 Regulations made by the Minister under section 80(1) of the
Surface planer or buzzer. Performs the tasks of dressing, squaring and straightening timber Machining short lengths of timber. Without the bridge guard. Without the appropriate training. Without PPE. Set
Angle Grinder MODEL 9553B MODEL 9555B
ENGLISH Angle Grinder MODEL 9553B MODEL 9555B 006649 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR
SHOP SAFETY AND TRAINING IN ACADEMIC DEPARTMENTS
Page 1 of 6 SHOP AND TRAINING IN ACADEMIC DEPARTMENTS 1. All students and employees (staff and faculty) are required to complete documented safety training prior to using any machines or power tools in
Machine Guarding. OSHA Office of Training and Education 1
Machine Guarding OSHA Office of Training and Education 1 Introduction Crushed hands and arms, severed fingers, blindness - the list of possible machinery-related injuries is as long as it is horrifying.
Core EZ. Operating Manual. Toll Free B East Broadway Avenue Tampa, FL 33619
Operating Manual 3702 West Central Avenue Santa Ana, CA 92704 Toll Free 1-866-987-7297 11 High Street Suffield, CT 06078 www.ussaws.com 8004B East Broadway Avenue Tampa, FL 33619 Introduction This manual
Subpart O - Machine Guarding. OTI 501 Paul A. Schlumper, PE, CSP
Subpart O - Machine Guarding OTI 501 Paul A. Schlumper, PE, CSP 1 We Will Cover: Machine Guarding Principles Subpart O - Highlights Mock Plant Walk-Through 2 Why are machines not guarded? No one would
Reducing Injuries: Using Power Tools at Work and at Home!
Reducing Injuries: Using Power Tools at Work and at Home! Action - Reaction.2 of a second can change your whole life! Action - Reaction Circular Saw at 4700 rpm.2 second = 15.6 revolu=ons 16 tooth blade
MAKER LAB Safety Instructions Power Tool Training
MAKER LAB Safety Instructions Power Tool Training Note: All the instructions from Basic Training apply to Power Tool Training. If you have not completed Basic Training, do so before you complete Power
Revised 8/1/2018 Page 1
1Guild of Oregon Woodworkers Shop Safety Test You must pass the Test with an 80% or better and self-correct it to 100%. Make sure you put the answers under the correct portion of the answer sheet for the
Table of Contents Responsibilities... 3 Department Head & Supervisors... 3 Employees & Student Laborers... 3 Machine Guarding Definitions 29 CFR
Machine Guarding Table of Contents Responsibilities... 3 Department Head & Supervisors... 3 Employees & Student Laborers... 3 Machine Guarding Definitions 29 CFR 1910.211... 4 General requirements for
CS150B CAP STAPLER OWNER S MANUAL
CS150B CAP STAPLER OWNER S MANUAL OPERATION MAINTENANCE SAFETY WARRANTY PLEASE READ! This manual contains important information about your new tool. REV 11/1/17 Versión en español disponible en STINGERWORLD.COM
Band Saw Operation & Safety
Band Saw Operation & Safety 2. Three teeth for thickness of material is a good rule to follow when cutting material. Any less and the band saw teeth can be broken off. 3. Read chart on front of band saw
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
Subpart O - Machine Guarding
Subpart O - Machine Guarding We Will Cover: Machine Guarding Principles Subpart O - Highlights Mock Plant Walk-Through Why are machines not guarded? No one would stick their arm, hand, finger, head, etc.
2" 18 gauge Brad Nailer Includes: 2 Allen wrenches & pneumatic tool oil
WARRANTY If you have any problems with this tool, please call FPC Corporation toll-free at 1-800-860-3838 before returning it to the place of purchase. Model 9750 2" Brad Nailer FPC Corporation warrants
CITY AND COUNTY OF DENVER CR&CF RISK UNIT Machine Guarding Safety Standard
CITY AND COUNTY OF DENVER CR&CF RISK UNIT 65.5.8 Machine Guarding Safety Standard 1.0 Introduction 2.0 Scope Lacerations to hands, fractured fingers, amputated fingers and hands are just a few of the more
Safe Work Method Statement SWMS 81213
Safe Work Method Statement SWMS 81213 This safe work method statement is generic in nature. It documents the risks and hazards associated with each step of a task and the control measures in place to minimise
Klinch-Pak Carton Closer Stapler
Klinch-Pak Carton Closer Stapler (KP-561M, KP-561PM, KP-560M, KP-560PM, KP-560PN22, KP-RCRR1, KP-RC555) Operation and Maintenance Manual IMPORTANT IMPROPER AND UNSAFE USE OF THIS NAILER WILL RESULT IN
Makerspace Student Machine Safety and Usage Manual
Makerspace Student Machine Safety and Usage Manual Prepared by: Thiago De Oliveira (2016-2017) Queen s University Last Updated: 21 st October 2016 General Safety Rules and Guidelines 1. Wear APPROPROPRIATE
2-1/2" 16 gauge Straight Finish Nailer Includes: 2 Allen wrenches & pneumatic tool oil
WARRANTY Model 9755 2-1/2" Finish Nailer If you have any problems with this tool, please call FPC Corporation toll-free at 1-800-860-3838 before returning it to the place of purchase. FPC Corporation warrants
SAT402 FINE WIRE STAPLER
SAT402 FINE WIRE STAPLER OWNER S MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE. SPECIFICATION TOOL MODEL SAT402 TOOL LENGTH 215 MM TOOL HEIGHT 165 MM TOOL
San Diego Fine Woodworkers Association Member Shop Safety Test
You must pass the Test with an 80% or better and self-correct it to 100%. Make sure you put the answers under the correct portion of the answer sheet for the test you are taking. Use the Guild Safety Answer
Band Saw Safe Operating Procedure 1. Operate only with the instructor s permission and after you have received instruction.
Band Saw Safe Operating Procedure 1. Operate only with the instructor s permission and after you have received instruction. 2. Remove jewelry, secure loose clothing, and confine long hair. 3. Always use
DEPARTMENT OF CONSUMER AND INDUSTRY SERVICES BUREAU OF SAFETY AND REGULATION GENERAL INDUSTRY SAFETY STANDARDS COMMISSION
DEPARTMENT OF CONSUMER AND INDUSTRY SERVICES BUREAU OF SAFETY AND REGULATION GENERAL INDUSTRY SAFETY STANDARDS COMMISSION (By authority conferred on the general industry safety standards commission by
Effective Date: 15-March Table of Contents
Version: 4 Page: 1 of 12 Table of Contents 1.0 Introduction... 2 1.1 Purpose... 2 1.2 Scope... 2 1.3 Definitions... 2 1.4 Responsibilities... 3 Environmental Health and Safety Office (EHSO) and applicable
HAND AND POWER TOOLS
USA office: 511 Avenue of America s, # 601, New York, NY 10011 Canada office: 655-32 nd Avenue, Suite 201, Lachine, QC., Canada, H8T 3G6 tel.: 514 634 3434 - fax: 514 634 9736 All PFI Standards and Best
WOODWORKING MACHINERY GUARDING
APPENDIX E WOODWORKING MACHINERY GUARDING The following requirements are restated from 29 CFR 1910.213, Woodworking machinery requirements. (a) Machine construction general. (1) Each machine shall be so
LOS ANGELES UNIFIED SCHOOL DISTRICT DIVISION OF ADULT AND CAREER EDUCATION SAFETY TEST FOR MACHINIST PROGRAM
LOS ANGELES UNIFIED SCHOOL DISTRICT DIVISION OF ADULT AND CAREER EDUCATION SAFETY TEST FOR MACHINIST PROGRAM School: Industry Sector: Manufacturing & Product Dev. Class: Date: Teacher: Room: (Please Print)
Building Bigger Things. Woodworking Tools and Machinery. Marking Gauge. Thumb Screw. Stop Screw. Shoe. Beam. Pin. Head. Face Plate
Woodworking Tools and Machinery Pin Shoe Face Plate Thumb Screw Head Stop Screw Beam Marking Gauge A marking gauge is used to mark a uniform width on a board. The steel combination square discussed in
OPERATOR S MANUAL FOR MODEL BLADE GRINDER
OPERATOR S MANUAL FOR MODEL 88-021 BLADE GRINDER Table of Contents Page Blade Grinder Safety and User Instructions 2 Unpacking the Grinder 5 Assembling the grinder 6 Adjusting the grinding angle 8 Adjusting
Impact Wrench MODEL TW1000. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ENGLISH Impact Wrench MODEL TW000 00605 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
University of Tennessee Safety Guidelines
University of Tennessee Safety Guidelines Program Subject: Hand and Power Tool Safety Guidance Approval Date: 12/1/2016 Next Scheduled Review: 6/1/2020 Date Effective: 12/1/2016 Contact Information: Program
ATBG280/6 Bench Grinder Bench Grinder ATBG280/6 230V-50Hz 280 Watt 150mm x 25mm Wheel size
Bench Grinder ATBG280/6 230V-50Hz 280 Watt 150mm x 25mm Wheel size SPECIFICATIONS Model Number : ATBG280/6 Nominal Voltage Power Consumption No load speed Wheel size Weight 230Volt 50Hz 280 Watts 2880
HANDHOLE SEAT GRINDER
1041-1601 HANDHOLE SEAT GRINDER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 9/17/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C. Wilson,
DANGER THIS TOOL FOR USE BY LICENSED OPERATORS ONLY. READ AND OBEY ALL SAFETY AND OPERATING INSTRUCTIONS BEFORE OPERATING TOOL.
THIS TOOL FOR USE BY LICENSED OPERATORS ONLY. READ AND OBEY ALL SAFETY AND OPERATING INSTRUCTIONS BEFORE OPERATING TOOL. R25 TOOL OPERATOR S SAFETY & OPERATING INSTRUCTION MANUAL SEMI-AUTOMATIC, LOW VELOCITY
General Safety. Start with a Safe Work Area. Rules about Extension Cords. Electricity can be Dangerous. Good Personal Safety is a Must
General Safety All power tools can be dangerous if both general and tool specific safety instructions are not followed carefully. General safety instructions apply to all power tools, both corded and cordless.
Operating Manual 6 Industrial Bench Grinder ATBG280/
Operating Manual 6 Industrial Bench Grinder ATBG280/6 804531 40 Year Australian Heritage The reputable name in bench grinders for 40 years Protect yourself and others by observing all safety information,
1369 & 1379 MOUNT KITS
November 15, 2014 Lit. No. 64573, Rev. 01 1369 & 1379 MOUNT KITS 1369 Ford Bronco, F 150 4X4 1992-96 1379 Ford F 250/350 4X4 1992-97 Ford F 250 2WD (over 8,500 GVWR) 1992-97 Ford F 350 2WD (over 10,000
Strip Nailer NR 90AD. Read through carefully and understand these instructions before use. Handling instructions
Strip Nailer NR 90AD Read through carefully and understand these instructions before use. Handling instructions 01Eng_NR90AD_Eng 1 27/6/07, 11:49 GENERAL OPERATIONAL PRECAUTIONS 1. Operate the power tool
Shipyard Machinery and Power Tool Safety. A Hazard Prevention Course. Conducted By The Port of San Diego Ship Repair Association. (Including Guarding)
Shipyard Machinery and Power Tool Safety (Including Guarding) A Hazard Prevention Course Conducted By The Port of San Diego Ship Repair Association This material was produced under grant SH-31243-SH7 from
GENERAL OPERATIONAL PRECAUTIONS PRECAUTIONS ON USING DISC GRINDER
GENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
Low Profile Tailgate Spreaders SWING AWAY Mount
November 15, 2016 Lit. No. 94432, Rev. 06 Low Profile Tailgate Spreaders SWING AWAY Mount Installation Instructions Read Owner's Manual before operating or servicing spreader. A DIVISION OF DOUGLAS DYNAMICS,
NITROSET TM SOLID PROPELLANT FASTENING SYSTEM USER MANUAL
NITROSET TM SOLID PROPELLANT FASTENING SYSTEM USER MANUAL PATENT PENDING Features and Benefits The revolutionary NITROSET TM system is a zero stand-off tool with many benefits to aid job completion and
HEAVY DUTY BENCH GRINDERS
HEAVY DUTY BENCH GRINDERS BGC-6 (240153) / BGC-8 (240154) Heavy duty construction for maximum service life CSA electrics for safety and reliability All ball bearing construction Steel wheel covers with
Impact Wrench. 19 mm (3/4 ) MODEL 6906
Impact Wrench 9 mm (3/4 ) MODEL 6906 002290 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
EXPLOSIVE ACTUATED TOOL SAFETY
CONSTRUCTION SAFETY EDUCATION PROGRAM #16 EXPLOSIVE ACTUATED TOOL SAFETY This education program provides a guideline for explosive actuated tools. It is intended to give contractors and workers practical
Example Written Safety Rules. General Rules: Loss Control Bulletin
General Rules: 1. The safe way is the only right way to do the job. 2. If you are not sure you understand a job or the safe way to perform it, ask your supervisor for instruction before beginning to work.
SAFETY INSTRUCTION TEST
SCHOOL: AREA: SAFETY INSTRUCTION TEST INDUSTRIAL EDUCATION - ELECTRONICS ADULT SCHOOL Name of student: Date: Address: Phone: In case of accident, notify: Address: Phone: Date Date of Enrolled: Birth: Age:
TOOLS FOR THE SPECIALIST UNDERWATER TOOLS
TOOLS FOR THE SPECIALIST UNDERWATER TOOLS PNEUMATIC TOOLS Performance data at an operating pressure of 6 bar (cont. flow). ANGLE GRINDER This handy angle grinder is particularly usable in tight spaces
MOUNT KIT. Installation Instructions CAUTION. Read this document before installing the snowplow. CAUTION
March 15, 2016 Lit. No. 78510, Rev. 01 35138 MOUNT KIT Yamaha Viking 2014 - Installation Instructions Read this document before installing the snowplow. See your sales outlet/website for specific vehicle
Impact Wrench MODEL 6905B MODEL 6906
ENGLISH Impact Wrench MODEL 6905B MODEL 6906 005305 DOUBLE INSULATION I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR
Machine Guarding/Shop Safety Risk Services Environmental Health & Safety 1370 Adams Avenue Costa Mesa, CA (714)
CONTENTS Authority Citations Purpose Hazardous Activities Equipment Operations Machine Guarding General Shop Rules Division of Responsibilities Program Notes Appendix A Appendix B Appendix C Appendix D
DANGER THIS TOOL FOR USE BY LICENSED OPERATORS ONLY. READ AND OBEY ALL SAFETY AND OPERATING INSTRUCTIONS BEFORE OPERATING TOOL.
THIS TOOL FOR USE BY LICENSED OPERATORS ONLY. READ AND OBEY ALL SAFETY AND OPERATING INSTRUCTIONS BEFORE OPERATING TOOL. SA270 TOOL OPERATOR S SAFETY & OPERATING INSTRUCTION MANUAL SEMI-AUTOMATIC, LOW
POWERNAIL CO. Model 1890U PowerStapler OPERATION AND MAINTENANCE MANUAL MANUAL DE OPERACION Y DE MANTENIMIENTO MANUEL D INSTRUCTIONS ET D ENTRETIEN
POWERNAIL CO. Model 1890U PowerStapler OPERATION AND MAINTENANCE MANUAL MANUAL DE OPERACION Y DE MANTENIMIENTO MANUEL D INSTRUCTIONS ET D ENTRETIEN WARNING Read this manual before you use this Powernailer.
Course 810. Hand and Power Tool Safety
Hand and Power Tool Safety This page intentionally blank OSHAcademy Course 810 Study Guide [Hand and Power Tool Safety] Copyright 2016 Geigle Safety Group, Inc. No portion of this text may be reprinted
LS12/LS12C. LS12C Item # LS12 Item # /10 LORTONE, inc Cyrus Way, Mukilteo, WA U.S.A
LORTONE LS12C Item # 053-093 LS12 Item # 053-090 LS12/LS12C Instructions and Parts List The LS12 is a quiet, fully enclosed, professional quality 12 slab saw. It comes equipped with a powerful screw-feed
Product Overview. Electric Pneumatic Hydraulic. Concrete and Masonry Dust Collection Systems Hot Work Zone Tools
Electric Pneumatic Hydraulic Product Overview Metalworking Surface Finishing Surface Preparation Concrete and Masonry Dust Collection Systems Hot Work Zone Tools www.csunitec.com Metalworking In the shop
JUDGING CRITERIA: Please refer to SkillsUSA Championships Technical Standards.
SkillsUSA California 2019 Regional Plumbing Competition SCOPE OF THE COMPETITION: - Knowledge Performance The contest criteria were drawn from the CTE Curriculum Standards for the Building Trades. The
INSTRUCTIONS & PARTS LIST FOR 270A, 270A-2, & 270A-4 SIOUX RIVET HAMMERS (SERIAL D)
Form Z489 Date 2009August8/C Page 1 of 4 INSTRUCTIONS & PARTS LIST FOR 270A, 270A-2, & 270A-4 SIOUX RIVET HAMMERS (SERIAL D) Read and understand these instructions before operating this tool. SAVE THESE
MOUNT KIT. Ford F-150 4X Installation Instructions CAUTION. Read this document before installing the snowplow. CAUTION
December 1, 2014 Lit. No. 64461, Rev. 06 64500 MOUNT KIT Ford F-150 4X4 2004-08 Installation Instructions Read this document before installing the snowplow. See your sales outlet/web site for specific
12mm (Max) 6mm (Max) 82mm (Max) 12mm (Max) 6mm (Max)
1 1 2 2 3 3 82mm (Max) 12mm (Max) 12mm (Max) 6mm (Max) 4 4 5 6 8 6mm (Max) 0.5 0mm 1 5 6 7 7 8 9 9 A = B 10 11 12 D B 1 13 14 15 0 C A D E 16 17 18 F G D B N H J G I K 19 A 20 G L 21 C K 1mm L M 1mm 22
LOCKOUT / TAGOUT PROGRAM
Page 1 of 7 1. SCOPE LOCKOUT / TAGOUT PROGRAM This Program outlines the purpose, rules, responsibilities and techniques to be followed by all University of Pittsburgh employees to guard against the unexpected
Model 2000 Pneumatic Powernailer OPERATION AND MAINTENANCE MANUAL MANUAL DE OPERACION Y DE MANTENIMIENTO MANUEL D INSTRUCTIONS ET D ENTRETIEN WARNING
POWERNAIL CO. Model 2000 Pneumatic Powernailer OPERATION AND MAINTENANCE MANUAL MANUAL DE OPERACION Y DE MANTENIMIENTO MANUEL D INSTRUCTIONS ET D ENTRETIEN WARNING Read this manual before you use this
Explanatory Information (NOT PART OF ANSI STANDARD)
3 General machine conditions 3.1 Grinding machine design and maintenance This standard recognizes that a wide variety of machines use bonded abrasive wheels. In this section the term grinding machine will