Venturi EVO 2 FPV. Thank you for purchasing the Venturi EVO FPV wing
|
|
- Julian McCarthy
- 6 years ago
- Views:
Transcription
1 Thank you for purchasing the Venturi EVO FPV wing The Venturi FPV is designed for First Person Viewing (FPV) and for UAV/Drone experimentation. There is a power system for this model, see the website for details. As well as this power system you will require: 2 x Standard size servos 43g (standard size) 1 x Long range receiver 1 x Lipo battery(s) (2x 3300mah 3S or 4S 11.1v) 1 x connectors set 1 x Transmitter capable of elevon mixing or mixing module 1 x Lipo compatible charger See website for power system details HOT GLUE GUN UHU POR CRITICAL DATA Venturi EVO 2 FPV CENTRE OF GRAVITY 185 +/-10mm BACK FROM THE FOAM WING LEADING EDGE AT ROOT CA GLUE TARGET FLYING WEIGHT 2000 grams without FPV gear & camera with 2 x 3300mah 4S batteries PVA WOOD GLUE
2 STEP 1 Fuselage assembly Carefully cut the tabs holding the parts on to the sheets of ply. Sand off the remaining tab and lightly bevel off the interlocking part of the piece, to help in assembly. STEP 2 Glue the 2 motor plates together using wood glue or UHU por, be careful to align them accurately, allow to dry Tabs Sand the tabs down as shown
3 Once you have trimmed and sanded the ply parts, its ready for assembly. Lay the fuselage side on a flat surface and assemble without glue. Once you have trimmed and sanded the ply parts, its ready for assembly. Lay the fuselage side on a flat surface and assemble without glue.
4 90 degrees IMPORTANT: check that the fuselage sides are aligned here before using glue You can use thin CA glue to hold the assembly together step by step. Soak the CA glue into the tab joints, use a weight to hold it in position. When you are happy that the fuselage is correct and aligned, run a bead of wood glue or UHU por around all the joint lines. Note! Put aside to dry / set Why not spray the fuselage with some acrylic car paint, black looks good
5 Wing Preparation Guide lines All FPV installations are different, but we offer some guide lines for the Venturi EVO 2 GPS Video TX There are some pre-cut slots in the fuselage to run cables from the wing to the autopilot /osd etc Using the spar holes, hold the fuselage against the wing and mark on the wing where these slots line up. Then you can cut slots in the wings for the servo, video tx etc cables Cut out the foam to accomodate your chosen servos and FPV gear When you are happy with this, remove the parts and laminate the wing with 72 micron laminate film. Receiver
6 Attaching wings to fuselage IMPORTANT! The tube spars are a tight fit in the wings, to help assembly, use insert the spars into the wings with twisting action making them easier to insert when you come to assemble the wings. Mark each spar at the centre point Slide the two carbon tube spars through the fuselage, short on at the front. Use a small amount of glue to hold the spars in place Run a small bead of UHU Por up each spar, Slide the wing down the spars Mark out where the wing will join the fuselage and use plenty of glue. Check the front and back of the wings for alignment. repeat for the other wing Bench
7 Elevon Preparation Using a sanding block, chamfer the leading edge of the Balsa elevons. Remember they are handed left & Right, Cover using just coloured tape/ L e a d i n g E d g e Using 25mm strapping tape or cutting 50mm tape down the centre, attach the elevons. 1. Run a strip down the back edge of one side of the wing, half on half off, offer up the elevon at a downward angle as show, attach it to the tape. 2. Angle the elevon up and apply the tape to the bottom part of the hinge. Ensure free movement. 3. Set the elevon 3mm short of the wing s end to stop it rubbing against the correx wing tip. Horn Assembly & Pushrod setup Solder Joint
8 Foam Parts Front Hatch Plate optional Hatch Rear Hatch Plate Rear Cover Upper Nose Lower Fuselage The foam parts installation is best in this sequence 1. Install motor mount & battery velcro straps 2. Glue in lower fuselage 3. Install all of your equipment, like the AP, ESC s Motor etc 4. Glue in rear section 5. Modify the nose section as desired to accommodate your cameras 6. Attach Hatch using tape and velcro 7. Glue on nose section, when all is working correctly You can hinge the hatch using strapping cut some channels out to accommodate the camera cables
9 Motor Mounting Outboard style: quieter, may need more nose weight to balance (CofG)wing Note: Upthrust, this is correct Inboard Style: Noisier, easier to get balance (CofG) Wingtips: Cut some stapping tape, and wrap it around the front section of the wingtip, top and bottom. Feed a strip through the slots and attach top & bottom.
10 Help! call or
(Build Instructions)
(Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS
More informationSpecifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive
Specifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive Airframe Kit (Included Contents) * Airframe Parts Sheets (Depron)
More informationULS Cherokee. Ultra Low Speed aircraft for indoor RC flying. Zippkits. Specifications: Required to complete:
Zippkits ULS Cherokee Ultra Low Speed aircraft for indoor RC flying. Specifications: Span- 28 inches Wing Area- 151 Sq/In Wing Loading- 3.0 ounces/ft Weight- 3.5 ounces RTF Build time- 1-2 Hours Radio-
More informationŸ Battery Strap Ÿ Paper Knife Ÿ Elevon Throw Gauge Ÿ Instructional Manual. Building Tools:
Congratulations on your purchase of the TuffBirds Spec Racer Flying Wing. We Hope these build instructions will help you complete the build easily. Though the build itself doesn't take much time, just
More informationHIGH-END TECHNOLOGY. Electric ducted fan rafale
HIGH-END TECHNOLOGY RC Electric ducted fan rafale First we want to thank and congratulate you with your decision in buying one of our Kits. The Rafale puts together very easily so there is not much explanation
More informationParts Identification
We are excited to introduce the Model Aero Aqua Sport. This is an excellent sport flyer, equally at home flying from grass fields, water, or even snow! The unique V-tail gives the Aqua Sport a distinctive
More informationE-AERO EPP PITTS KIT From BP HOBBIES. Parts Included in kit
E-AERO EPP PITTS KIT From BP HOBBIES Parts Included in kit Thank you for purchasing the BP Hobbies/E-aero EPP Pitts. Please take the time to read through the instruction manual before beginning the build.
More informationuin RC FPRC ZERO Specificationss Empty Weight
Flying Pengu uin RC FPRC ZERO Specificationss Wing Span 42.75 (1085 mm) Fuselage length 30.5 ( 775 mm) Empty Weight 9.5 10 oz. (150 160g) Estimated Flying Weight 20 255 oz. (320 400g) Wing Area: 151 sq.
More informationVT-ALLROUNDER V4 1500MM CORO 3/4 Channel Trainer Airplane
Congratulations on your purchase of the VT- AllRounder 1500MM Trainer Airplane Kit.. Hope these build instructions help you complete the build. Though the build itself doesn't take much time, just be sure
More informationCombat Foamie. An electric powered model made from sheet foam for full contact combat matches. Designed by. Plan by Paul Bradley. Jerry W.
Combat Foamie An electric powered model made from sheet foam for full contact combat matches Designed by Jerry W. Hagood Plan by Paul Bradley July 2010 Combat Foamie Top View 22.9 CG is 7.3 back from nose
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationC-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
More information3D Fun Flyer Build Guide 30 Span
3D Fun Flyer Build Guide 30 Span Designed by Me_Wantee RC Groups Thread http://www.rcgroups.com/forums/showthread.php?t=659911&pp=25 My Setup Motor Axi 2212/34 Prop 10 x 4.7 Speedie 18A Servos are eflight
More informationPrint template tiles and put together with clear tape to complete template.
Print template tiles and put together with clear tape to complete template. Cut each pattern out with scissors or use a razor and strait edge ruler. Use the ruler as a guide for the razor to get nice strait
More informationPrecut Wingola Kit Instructions
Precut Wingola Kit Instructions Below is the precut option. Battery compartment, Receiver and Servo Trays are cut for mini radio gear. This is the uncut version. It has the placement laid out for the radio,
More informationParkJet Builder s Manual
ParkJet Builder s Manual Thank you for purchasing the ParkJet. The ParkJet is a profile ducted fan airplane that can be flown in a larger park. The ParkJet was initially designed by Scott Stoops and modified
More informationConstruction Guide for Quick Build MIG-29 Design by Tomas Hellberg
Construction Guide for Quick Build MIG-29 Design by Tomas Hellberg This kit is very simple to put together. The biggest danger in messing up this kit is gluing the pieces to your work bench. But before
More informationBuilding Tips This model can be built using the following types of adhesives:
Page 1 Building Tips This model can be built using the following types of adhesives: Epoxy (with or without microballons) Odorless cyanoacrylate (CA) with accelerator UHU Creativ for Styrofoam (or UHU
More information1. Build the bottom first - make sure your table is flat. Build the entire plane using foam safe CA and kicker. The best technique is to spray kicker
Wxá zç uç `tçué 1. Build the bottom first - make sure your table is flat. Build the entire plane using foam safe CA and kicker. The best technique is to spray kicker on one part and apply a sparing amount
More information34" PELICAN by CRASH TEST HOBBY
34" PELICAN by CRASH TEST HOBBY The Pelican is a 34" trainer that can level its own wings and put its nose on the horizon once trimmed and balanced. It can handle more wind than most EZ flying planes in
More informationConstruction Guide for Quick Build F-22 Raptor Design by Tomas Hellberg
Construction Guide for Quick Build F-22 Raptor Design by Tomas Hellberg This kit is very simple to put together. The biggest danger in messing up this kit is gluing the pieces to your work bench. But before
More informationZ II Basic Build Instructions
Z II Basic Build Instructions Kit Contents: (2) Precision EPOR molded wing panels (2) Custom balsa pieces (trailing edge) (6) Fiber glass reinforcement spars (1) CNC T-6 aluminum motor plate Corrugated
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More informationHIGH-END TECHNOLOGY. Electric ducted fan Starfighter
HIGH-END TECHNOLOGY RC Electric ducted fan Starfighter First we want to thank and congratulate you with your decision in buying one of our Kits. The Starfighter puts together very easily so there is not
More informationSGTalon s Enterprise-A Foamie Build Guide. SGTalon s. Enterprise. Enterprise--A. Assembly Instructions
SGTalon s Enterprise SGTalon s Enterprise--A Enterprise Assembly Instructions Page 1 4-13-2013 SGTalon s Enterprise *******Recommended Hardware******** 2.6oz 250w Motor and Speed Control with 8x6 prop
More informationF100 Super Sabre instructions.
F100 Super Sabre instructions. The F100 is a Jet model for the Wemotec 480 Minifan. Start with taking the parts out of the sheet and sand of the connection tabs. Instructions RBCkits F100 Super Sabre 1
More informationS.E.5a (Build Instructions)
S.E.5a (Build Instructions) Specifications Wingspan: 38 cm Length: 31cm Flying Weight: 41 Channels: 3 (Rudder Elevator Throttle) Suggested Receiver: 3Ch Brick Motor: 7mm Geared Motor Airframe Only Kit
More informationRevolution 3D-mini ARF
Revolution 3D-mini ARF 1 Included Hardware 4 Dubro Micro Control Horns #DUB848 2.32 x 18" Linkage Wire (Music Wire) 1 1.5 x 1.25 x 1/8 Balsa Ply (for motor mount) 1 5" piece of Velcro (Optional recommended,
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationALBATROSS by CRASHTESTHOBBY.COM
ALBATROSS by CRASHTESTHOBBY.COM The Albatross is a unique slow flyer designed to put its nose on the horizon and level its own wings without a pilot. It is very quiet and designed to use inexpensive electronics.
More informationMagpie. Foam Trainer. Magpie Specifications
Magpie Foam Trainer Magpie Specifications Length: 34in. Wingspan (SF): 46in. Wing Area (SF): 414in 2 Wingspan (SP): 40in. Wing Area (SP): 360in 2 Weight (without battery): 12oz. Thank you for purchasing
More informationLANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.
LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for
More informationSAAB JAS 39 Gripen. Building Instructions Designed by: Steve Shumate. Taken From:
SAAB JAS 39 Gripen Building Instructions Designed by: Steve Shumate Taken From: http://www.rcgroups.com/forums/showthread.php?t=308830&page=1 Lightly tack glue the paper templates to the foam sheets using
More information6mmFlyRC.com Super Bandit Assembly Instructions
Assembly Instructions Start the assembly with forward fuselage. Lay the two fuselage sides down on a flat surface and glue the foam corner doublers to the locations shown on the plans. Make sure to make
More informationThank you for your purchase of the Lee Ulinger, FoamtanaS, Yak-55, or Extra 330 3D Depron foam, Aerobatic airplane.
Thank you for your purchase of the Lee Ulinger, FoamtanaS, Yak-55, or Extra 330 3D Depron foam, Aerobatic airplane. Tools you will need to build Recommended additional items: #11 hobby knife Motor: Hacker
More informationMamba. Combat Wing Glider
Mamba Combat Wing Glider Congratulations for your purchase of the Mamba radio-controlled combat glider! The Mamba is a very fast and agile glider and yet it can stay up in very light winds when built correctly.
More informationWing. Gently bend the top of the wing over. With the paper removed, it should produce a nice curve.
Fuselage Remove the paper in the four areas shown. Basically, from the trailing edge of the canard forward in the three nose segments and on the rear bottom of the fuse. Normal B fold for the sides but
More information1/6 PA-25 PAWNEE. *Specifications are subject to change without notice.*
1/6 PA-25 PAWNEE INSTRUCTION MANUAL [ A335 Kit ] Wing Span : 72 in / 1830 mm Wing Area : 736 sq in / 47.5 sq dm Flying Weight : 6.6 lbs / 3000 g Fuselage Length : 48 in / 1220 mm Requires : "Glow Power"
More informationInstructions - Stobel V2
Instructions - Stobel V2 Congratulations on the purchase of your Stobel, a high end DLG-competition model from LE-composites. We hope you will be happy and successful. To ensure the optimum build we ask
More informationMiniacRC MIGHTY MINI P40 WARHAWK
Hand-Cutting and Skins) MiniacRC MIGHTY MINI P40 WARHAWK FliteTest style RC model Build Instructions Make sure that the orientation for molded pieces such as the scoop rings and landing gear housings are
More informationCitabria Pro. Aerobatic Parkflyer. by Joel Dirnberger
Citabria Pro Aerobatic Parkflyer by Joel Dirnberger Revision C: December 21, 2004 Citabria Pro Building Instructions Length: Wingspan: Wing Area: Flying Weight: Wing Loading: Functions: Specifications:
More informationGYM-E. Instruction Manual - Version 1.03
GYM-E Original Design by Todd Long Instruction Manual - Version 1.03 Span 31 in. / Length 27 in. / Area 265 Sq. In. / Weight 4.5-6.5 oz. Gym-E kit reproduced with permission by Stevens AeroModel 2008 Stevens
More informationF-16 Falcon 70mm EDF
F-16 Falcon 70mm EDF Instruction manual Specifications: Winspan: 640 mm Length: 990 mm Weight: 900-1100 gram Ducted fans 70mm x 1 Required tools and components:. 4 ch. Computer Radio system w/ 2 servos.
More informationDRAFT COPY BUILDING INSTRUCTIONS FOR BLACKBURN BUCCANEER S2 VERSION 1 (BETA BUILD) BY MARK DOUGLAS
BUILDING INSTRUCTIONS FOR BLACKBURN BUCCANEER S2 VERSION 1 (BETA BUILD) BY MARK DOUGLAS COPYRIGHT MARK DOUGLAS 2011 THIS IS A "SHORT" KIT FOR EXPERIENCED BUILDERS AND FLYERS ONLY, DESIGNED BY A SHED DWELLING
More informationDandy Sport Builder s Manual
Dandy Sport Builder s Manual Thank you for purchasing the Dandy Sport. The Dandy Sport has been designed as an easy to build aileron trainer. Take your time and enjoy building this plane. Specifications:
More informationCover the wing trailing edge and the aileron leading edge with strapping tape as shown.
Cover the wing trailing edge and the aileron leading edge with strapping tape as shown. The aileron hinges are done using strapping tape on the top and bottom surfaces of the ailerons as shown. Make sure
More informationHigh performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
More informationBuilding a Giant Scale Electric EINDECKER Part 2
Building a Giant Scale Electric EINDECKER Part 2 John Bernard N1KUB AMA 58903 IMAA 28971 In Part-1 of this series, we explored the 100 Eindecker kit from SR Batteries and started building the fuselage.
More informationORIGAMI E2. An electric powered model made from sheet foam based on the configuration of a paper glider. Concept and general arrangement by
ORIGAMI E2 An electric powered model made from sheet foam based on the configuration of a paper glider. Concept and general arrangement by Jack Pignolo Plan by Paul Bradley February 2010 ORIGAMI E2 38
More informationJAMISON SPECIAL. Building Guide
JAMISON SPECIAL Building Guide WING Mark then drill holes for wing jig rods. Slide Ribs onto jig rods Mark the rib positions on 1/16 x 1 trailing edge, 1/4 x 1/4 leading edge & 1/4 x 1/4 spars Pin ribs
More informationSwitchback Sport Builder s Manual
Switchback Sport Builder s Manual Thank you for purchasing the Switchback Sport. The Switchback Sport has been designed for the novice to intermediate pilot who wants a plane with good performance that
More informationGRIM REAPER Building Instructions by CRASHTESTHOBBY.COM
GRIM REAPER Building Instructions by CRASHTESTHOBBY.COM The Reaper is one of the toughest planes on the planet. The Grim Reaper is our club's favorite combat plane. It is also used for FPV. It has an amazing
More informationCorvus Racer CC
Corvus Racer 540 35CC Item No:L-G035008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio mm mm 1200sq in (77.4sqdm) 9.9-12lbs(4.5-5.5kg) 91-1.20(2C) 1.10-1.40(4C) 20-40cc
More informationThe Olympic DLG. (Discus launch glider) by Chris Brislin
The Olympic DLG (Discus launch glider) by Chris Brislin 1 Contents Parts List/ What you need 3 Before you begin 4 Wing Construction 5-9 Pod Construction 9-13 Tail assembly 13-? Control linkages 9-10 Finishing
More informationCorvus Racer Colour schemes. AeroPlus RC Copyright 2013 All Rights Reserved
Corvus Racer 540 59 Item No:A E050003 Specifications WING SPAN: 59"(1500mm) LENGTH: 54.1"(1374mm) WING AREA: 654sq.in.(42.2sq.dm.) FLYING WEIGHT: 4.6 5.3lbs(2000 2300g) Electric:Brushless outrunner 8Oz.
More informationMagpie AP. Aerial Photography Airplane
Magpie AP Aerial Photography Airplane Magpie Specifications Length: 36in. Wingspan: 54in. Wing Area: 486in 2 Weight (without battery): 19 oz. Thank you for purchasing the Magpie AP. This model is an elevator/rudder
More information68" Storm Chaser Building Instructions
68" Storm Chaser Building Instructions The Storm Chaser is a big solid EPP/ FPV design that can take abuse that would destroy other planes. It is easy to fly and can level its wings and put its nose on
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationSPUNKY ASSEMBLY MANUAL
SPUNKY ASSEMBLY MANUAL Please read the tips section at the back of this manual regarding the use of laser cut parts. The proper removal and preparation of these parts is important. When laser cut, some
More informationZAGI-3C. Features a 3 Carbon Fiber Spar Matrix. New 2000 upgrade... Lighter Thinner Stronger Faster!
New 2000 upgrade... Lighter Thinner Stronger Faster! ZAGI-3C Features a 3 Carbon Fiber Spar Matrix Wing span 48 Wing area 3.33 sq. ft. Airfoil ZAGI 2000 Weight 17-19 oz. Speed range 6 to 45+ mph Radio
More informationStearman PT-17 KIT WARRANTY
Stearman PT-17 KIT # K-306 Assembly Instructions Version 2 02-17-16 Designed by Tom Herr WARRANTY Sig Manufacturing Co, Inc. guarantees this kit to be free from defects in both material and workmanship
More informationInside F5J. Assembly Manual
Inside F5J Assembly Manual Original work in German by GRÜNER CNC Service, all rights reserved 2015. This version is published with the expressed permission of GRÜNER CNC Service. Download the original
More information35 Magnum. Instruction Manual
EPP EPP 35 35 Magnum Rebel Z Instruction Manual This is how your kit will arrive When cutting the hardware package open use caution. The contents are semi-coiled to fit in the box. They will spring open
More informationI hope you enjoy the Spirit as much as I have. Scott DeTray Model Aero
We are excited to introduce the Model Aero Spirit. Inspired by the magnificent Northrop Grumman B-2 Spirit Stealth Bomber, the Spirit is a great flyer, on land or water. It tracks like an arrow and is
More informationDesigned by Steve Shumate Adapted from the North Star design by Laddie Mikulasko
Model Aero Polaris Specifications: Designed by Steve Shumate Adapted from the North Star design by Laddie Mikulasko Wing area: 343 sq in Span: 29.0" Length: 38.4" Weight RTF: 18 to 22 oz (prototype weighed
More informationMXS R 30CC. Item No:L G Specifications. 67 1/2"(1720mm) (2C) (4C) 26 35cc gas DLE 30/35RA MLD35 JC30Evo.
MXS R 30CC Item No:L G030008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description Covering Material Carbon Fibre : 75"(1915mm) 67 1/2"(1720mm) 1023sq in(66sq
More informationKam Aero 43% Extra 300.
Stab Sheeting Kam Aero 43% Extra 300. Stabs / Elevator: Make your skins using the same method as you did for the fuselage foam parts. The stabs require 8 sheets (4 per stab) of 4 x 48 A grain sheeting.
More information28in Super EVA Foam. F-22 Raptor Kit. Specifications. Wingspan: 27.5in (700mm) Length: 38.3in (975mm) Flying Weight: Approx. 1.
28in Super EVA Foam F-22 Raptor Kit Specifications Wingspan: 27.5in (700mm) Length: 38.3in (975mm) Flying Weight: Approx. 1.2lbs (530g) Dear Customer, Congratulations on your purchase of 28in F22 Raptor
More informationMiniacRC MIGHTY MINI Ju 87 SIMPLE STUKA
MiniacRC MIGHTY MINI Ju 87 SIMPLE STUKA FliteTest style RC model Build Instructions General Tips) Confirm that the main posterboard pieces (turtle decks, hatch covers, etc ) are cut out with the proper
More informationSbach 1,2m 3D/aerobatic EPP model Building instructions
Sbach 1,2m 3D/aerobatic EPP model Building instructions Please refer to the Diagram sheet Diagrams A, B Press 2 carbon strips (1x3x1000 mm) into the grooves in the sides of the fuselage central part (the
More informationMercurE Mini Old Timer Electric Model
MercurE Mini Old Timer Electric Model MercurE Specifications Wingspan: 31.6 in. Length: 20.6 in. Wing Area: 153 sq. in. Weight (Ready to Fly): 4.9 to 5.4 oz. Wing Loading: 4.6 5.1 oz. / sq. ft. Version
More informationGLADIATOR XL Building Instructions by CRASHTESTHOBBY.COM
GLADIATOR XL Building Instructions by CRASHTESTHOBBY.COM The Gladiator is one of the toughest FPV planes on the planet. It is designed to be a low drag plane that can fly slow and carry FPV equipment.
More informationHobby Lobby Zip Supplementary instructions Please refer to the included drawings while using these assembly instructions
Materials needed: 15 or 30 minute epoxy Medium CA Masking tape Scotch tape Servo Tape Wax paper Tools Needed: Pencil or marker Flat building surface Hobby knife or razor blade 7/64" or 3mm drill bit 3/16"
More informationWarbird Series Zero - 32 Assembly Manual
Warbird Series Zero - 32 Assembly Manual Specifications Wing Span: 32 inches Wing Area: 210 in 2 Fuselage Length: 26 inches Weight (ready to fly): 11 to 13 oz. Wing Loading: 7.5 to 8.9 oz/ft 2 Designed
More informationEdge 540 V3 35CC. Scheme A. Item No:L G Specifications. Flying Weight
Edge 540 V3 35CC Item No:L G035016 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description 76 (1930mm) 74 (1879mm) 1200sq in(77.4sqdm) 9.9 12lbs(4.5 5.5kg) 91 1.20(2C)
More informationRSM DISTRIBUTION Presents
RSM DISTRIBUTION Presents MOSQUITO By Jack Sheeks Photo _ Jack Sheeks Semi Scale Twin Stunter Wing Span: 58" Length: 37-3/4 Area: 579 sq. in. Engine: Two.35 -.40 www.rsmdistribution.com Call (951) 678
More information+++ construction manual SR 71 Blackbird (EDF Version) from JetCom +++
Table of content: Page List of material and overview of provided frames 3 Mounting of main gear 4 Mounting of nose gear 5 Mounting of elevons 6 Installation of the rudders 7 Mounting of the rudders 9 Installation
More informationModel Aero Aqua Cat, Aqua Cat SE, and Aqua Jet Build Guide
Model Aero Polaris Model Aero Aqua Cat, Aqua Cat SE, and Aqua Jet Build Guide Note: Aqua Cat SE and Aqua Jet specific instructions are at the end of the build guide. Some photos may depict the Polaris
More informationTaylorcraft Indoor / Cul-De-Sac Flyer
Taylorcraft Indoor / Cul-De-Sac Flyer Taylocraft Specifications Wingspan: 28.0 in. Wing Area: 117 sq. in. Weight (Ready to Fly): 3.0 3.1 oz. Wing Loading: 3.7 3.8 oz. / sq. ft. LIABILITY RELEASE In that
More informationF3A -70E ASSEMBLY MANUAL
F3A -70E ASSEMBLY MANUAL The new F3A-70E, was designed in an extremely lightweight structure, the all wood airframe, and the new revolutionary Lift Generator on landing gear give the F3A-70E an impressive
More informationCOMET 24" HELLCAT REPRODUCTION ASSEMBLY GUIDE
COMET 24" HELLCAT REPRODUCTION A RUBBER POWERED 24" WING SPAN MODEL BY PAUL BRADLEY ASSEMBLY GUIDE AUGUST 2016 CHANGES MADE TO THE ORIGINAL The following changes were made to the original Comet kit structural
More informationEPP Rebel Z 35. White Red w/ Blue Orange w/ Blue Orange w/burgundy Other. Specs. Color - Bottom White Black Checkers Silver Checkers Other Checkers
EPP Rebel Z 35 Specs AUW ~10.0oz Width 35.28 Length 34.67 Wing Area 1.44 sqft Horz Area 2.35 sqft Vert Area.91 sqft
More informationPrint scale 5 inches
www.mikeysrc.com FPV V3 Slow flying, stable plane for FPV. PDF NOTES and TIPS **PRINT ONLY THIS PAGE FIRST** to check that the printed scale is correct. The black line below should be five inches long.
More informationINS TRUC T I ON M A NU A L
INS TRUC T I ON M A NU A L Packing list: 1: PP F6F fuselage *1 2: Carbon tube 5*5*940mm *1 3: Pull rod *4 4: Motor mount *1 5: Quick rod adjuster *4 6: Hinge *4 7: M3 screws *4 8: Hook and loop tape *1
More informationSirius instruction manual
Sirius instruction manual Thank you for purchasing the eagle wing plane.the sirius is designed for First-Person-Vision (FPV) application spec ifically. Due to the high wingand push prop design, the on-board
More informationMOUNTAIN MODELS P-51 Mustang. 1/12 Scale Electric Park Flyer. Copyright Mountain Models
1 MOUNTAIN MODELS www.mountainmodels.com P-51 Mustang 1/12 Scale Electric Park Flyer Wingspan: 37, Wing Area: 254 sq. in., Weight: 15 to 19.5 oz Instructions Version 1.4, May 23, 2007 Kit Contents: 2 1.
More informationZlín Z-37A Čmelák ("Bumblebee ) mm. Assembly Instructions and recommended equipment of the RC model
Zlín Z-37A Čmelák ("Bumblebee ) - 1 530mm Assembly Instructions and recommended equipment of the RC model Technical information: Wingspan: 1530 mm Overall Length: 920 mm Flying weight: ~1 700g RC Functions:
More informationZlín Z-37A Čmelák ("Bumblebee ) 850 mm. Assembly Instructions and recommended equipment of the RC model
Zlín Z-37A Čmelák ("Bumblebee ) 850 mm Assembly Instructions and recommended equipment of the RC model 1 Technical information: Wingspan: Overall Length: Flying weight: RC Functions: 850 mm 610 mm ~380
More informationNASTY Build Guide. Supplies needed
NASTY Build Guide Supplies needed Blucore or Depron Foam. Blucore (Fan Fold Foam) is available at Lowes. Approximately $25 for 50 feet of Blucore. Depron can be ordered on the internet for slightly more.
More informationHercules Twin Puller 66" and 78" Building Instructions
Hercules Twin Puller 66" and 78" Building Instructions The EPP Hercules Twin Pullers are some of the toughest BIG FPV planes on the planet. They are unique because they can take off the ground without
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationThe BIPE NX Assembly Manual
The BIPE NX Assembly Manual Specifications Wing Span: 34 inches Wing Area: 550 in 2 Fuselage Length: 36 inches Weight (ready to fly): 20 to 24 oz. Wing Loading: 5.2 to 6.3 oz/ft 2 Designed by Jim Vigani
More informationSwitchBack Senior. SwitchBack Senior Specifications
SwitchBack Senior SwitchBack Senior Specifications Wingspan: 55.4 in. Length: 41 in. Wing Area: 597 sq. in. Weight (Ready to Fly): 34 to 37 oz. Wing Loading: 8.2 to 8.9 oz. / sq. ft. Version 1.05, March
More informationPITTS S2S CONSTRUCTION
PITTS S2S CONSTRUCTION FUSELAGE CONSTRUCTION 1) Place the right fuselage side over the plan and mark the former positions. Place the left side over the right side and mark the former positions. Glue F1
More informationKodo build guide 1.4
Kodo build guide 1.4 Please do not share files that you bought Development of a new plane and support of the old ones is very time consuming. Only with your help I can focus fully on this project and spend
More informationPfalz E1 Monoplane 48 EZ Build Version
Pfalz E1 Monoplane 48 EZ BUILD Pfalz E1 Monoplane 48 EZ Build Version R/C Scale Model Instructions CONTACT INFORMATION Designed by M.K. Bengtson Prototype by Robert Hoffman Manufactured and Distributed
More informationWhite Red w/ Blue Orange w/ Blue Burgundy w/ Orange Other
Specs AUW ~6.5oz Width 32.875 Length 29.50 Wing Area 1.35 sqft Horz Area 2.22 sqft Vert Area 1.26 sqft Suggested Hardware ~25g 90 watt Motor 12 amp ESC Servos 6g+ (4) 2s LiPo (300-500mAh) 4ch Radio/Rx
More informationCOMET SENIOR DART REPRODUCTION ASSEMBLY GUIDE
COMET SENIOR DART REPRODUCTION A RUBBER POWERED 24" WING SPAN MODEL BY PAUL BRADLEY ASSEMBLY GUIDE JANUARY 2018 CHANGES MADE TO THE ORIGINAL The following changes were made to the original Comet kit structural
More informationT-15 EDF INSTRUCTION MANUAL. Wingspan.31in. Weight..2.5 lb. EDF...70mm 12 Blade ToughJets, LLC Kittery, ME Page 1 of 22.
TM T-15 EDF INSTRUCTION MANUAL Specifications Wingspan.31in Length..41.75in Wing Area 515 sq in EDF...70mm 12 Blade Weight..2.5 lb Radio...3 channel Motor...Brushless Battery 14.8v 2200mah 40c 2013 ToughJets,
More information