1x12 Wood Bulk Bins [1]

Transcription

1 [1] Submitted by Ana White [2] on Fri, :40 Page 1 of 24

2 [1] Additional Photos [3] Page 2 of 24

3 [4] [5] [6] First came our daughter's birthday. Followed by Christmas just ten days later. And four days after Christmas, we celebrated our son's birthday. December is truly a joyful season for us. We have been blessed with more than we could ever ask for, all within two weeks. But the kids, unfortunately, end up with more than they could have ever asked for, all within two weeks. And this year, with a baby, the toys are especially small and it's hard to keep up with how fast our little guy can pull his toys out. So we thought we'd give stacked bulk bins a try. I wanted to build this set of bulk bins out of 1x12 boards, so it would be easy for you to make at home without a tablesaw (and the Rogue Engineer also put out some really awesome bulk bin plans here that use plywood [7]). It did take a little thinking, especially since I was adamant about avoiding making angled rip cuts (not fun) to get the front trim board to meet up nicely with the sides. Page 3 of 24

4 So here's what we did - Page 4 of 24

5 I cut 1x12 boards (see cut list for the actual lengths) FIRST at 15 degrees off square. Then I flipped the boards over and nipped the other corner off at 40 degrees off square. Cutting the 15 degrees off square cut first means less waste (just an itty bitty triangle piece is wasted). TIP: When you make your first 15 degree cut, the leftover piece already has a 15 degree cut on it for you. The sides are longer than the dividers, to cover the 1x4 ends (it will all make sense here shortly). Cutting the sides and dividers for this project was the hardest part (even though it wasn't really hard at all). We ended up making three of these bulk bins, so I turned my first cuts into patterns and just replicated them. To assemble, we just attached the bottoms to the sides and dividers, everything flush to the BACK. The dividers do not make it all the way to the front so the 1x4 front board can sit inset. Page 5 of 24

6 Since we are just building with screws, we glued everything. That, and my kids like to climb on stuff. This is not cheap insurance. This is proactive maintenance. Page 6 of 24

7 See how that 1x4 fits inset? If we had cut the dividers the same as the sides, there's have been a weird little triangle hole on the ends. Or we'd be ripping the bottom board front edge at a 15 degree angle. Page 7 of 24

8 Then we just finished screwing the 1x4 to the sides and dividers, and added the top. We also planked the back with 1x6 boards because we had some in our scrap pile but 1/4" plywood would have done the trick. Page 8 of 24

9 I used my favorite stain, Rustoleum Early American [8]. I just wipe a single coat on with a paper towel. Almost too easy. Page 9 of 24

10 We applied Watco Lacquer [9] over top, and it's time to show the toys who's boss. I think they turned out pretty well! Page 10 of 24

11 And even someone as uncoordinated as me can toss a toy in the general direction, and somehow, it lands in one of the cubbies. Page 11 of 24

12 I'm pleased with how this plan turned out and am confident you'll love it too. If you do build, please share pictures and your experience building too - we'd love to see your version too! Page 12 of 24

13 Page 13 of 24

14 Have a great weekend! XO Ana + Family Summary: DIY Wood bulk bins from 1x12 boards - easy plans by ANA-WHITE.com CategoriesProject Type: Storage Woodworking Plans [10] Bookshelf and Bookcase Plans [11] Crate Plans and Projects Made with Crates [12] Cubby Project Plans [13] Room: Kids and Toys [14] Nursery and Baby [15] Skill Level: Intermediate [16] Style: Children's and Kid's Room Furniture and Toy Plans [17] Page 14 of 24

15 PER BULK BIN 12 feet of 1x12 boards 4 feet of 1x4 boards 1/4 sheet of 1/4" thick plywood or other hardboard 2" self tapping screws 3/4" finish nails for attaching the back Common Materials: Elmer's Wood Glue [18] Elmer's Wood Filler [19] Tools: Dimensions: Page 15 of 24

16 [20] [21] [22] Cut List: FOR ONE BULK BIN 10-13/16" long - one end cut at 15 degrees off square, short point measurement Page 16 of 24

17 11-1/4" long - one end cut at 15 degrees off square, short point measurement 45" (top and bottom) 43-1/2" long 1-1/4" 45" x 12-3/4" General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Page 17 of 24

18 [23] Cut the sides and dividers first at 15 degrees off square. Note that the dividers are shorter than the sides. Then cut from the opposite side at 40 degrees. Label dividers and sides. Step 1 Page 18 of 24

19 [24] Attach top and bottom to dividers with 2" self tapping screws. If you wood splits, you'll need to predrill holes. Use glue at all joints. Step 2 Page 19 of 24

20 [25] Attach 1x4 to front with screws and glue. Step 3 Page 20 of 24

21 [26] Attach back to all dividers and sides and top and bottom with 3/4" brad nails and glue. Step 4 Page 21 of 24

22 [27] If you do stack, make sure you attach each bin to the upper bin, and attach the whole thing to the wall - it will be very easy for a little one to climb up the front and tip forward. Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed. Step 5 Source URL: x12-wood-bulk-bins Links [1] lk-bins [2] [3] Page 22 of 24

23 ood-kids-1.jpg [4] ood-kids-2.jpg [5] 20bin%20wood%20kids%2011.jpg [6] 20bin%20wood%20kids%2010.jpg [7] [8] are/ultimate-wood-stain [9] acquer-clear-wood-finish [10] [11] kshelves [12] [13] [14] [15] d-baby [16] ediate [17] [18] [19] struction# [20] [21] [22] [23] %20toy%20chicken%20coop%20bulk%20step%201.jpg [24] %20toy%20chicken%20coop%20bulk%20step%202.jpg [25] %20toy%20chicken%20coop%20bulk%20step%203.jpg [26] %20toy%20chicken%20coop%20bulk%20step%204.jpg [27] Page 23 of 24

24 %20toy%20chicken%20coop%20bulk%20step%205.jpg Page 24 of 24