Licensed Copy: RRICTISQ RRICTISQ, ISO/Exchange Russia, 23 November 2004, Uncontrolled Copy, (c) BSI

Size: px

Start display at page:

Download "Licensed Copy: RRICTISQ RRICTISQ, ISO/Exchange Russia, 23 November 2004, Uncontrolled Copy, (c) BSI"

Primrose Phillips
6 years ago
Views:

2 BRITISH STANDARD BS EN 391:2002 The European Standard EN 391:2002 has the status of a British Standard ICS NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

3 BS EN 391:2002 National foreword This British Standard is the official English language version of EN 391:2001. It supersedes BS EN 391:1995 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee B/518, Structural timber, which has the responsibility to: This British Standard, having been prepared under the direction of the Sector Policy and Strategy Committee for Building and Civil Engineering, was published under the authority of the Standards Policy and Strategy Committee on 28 January 2002 BSI 28 January 2002 ISBN X aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments

4 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 391 October 2001 ICS Supersedes EN 391:1995 English version Glued laminated timber Delamination test of glue lines Bois lamellé collé Essai de délamination des joints de collage This European Standard was approved by CEN on 3 September Brettschichtholz Delaminierungsprüfung von Klebstofffugen CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG Management Centre: rue de Stassart, CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. B-1050 Brussels Ref. No. EN 391:2001 E

5 Contents Page 1 Scope Normative references Terms and definitions Symbols Requirements Delamination test of glue lines Principle Apparatus Pressure vessel Drying duct Balance Metal wedge and wooden hammer Preparation of test pieces Procedures General Measurement and evaluation of delamination Test cycle for method A Test cycle for method B Test cycle for method C Results General Total delamination Maximum delamination Test report

6 Foreword This European Standard has been prepared by Technical Committee CEN/TC 124, Timber structures, the Secretariat of which is held by DS. This European Standard supersedes EN 391:1995. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2002, and conflicting national standards shall be withdrawn at the latest by April NOTE It is considered desirable to maintain the same clause numbers consistently throughout this series of standards. Consequently, some clauses are void in this edition of this standard, but it is envisaged that future editions may need to include text in the clauses. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 3

7 Introduction Two delamination methods called A and B are suitable for adhesives of type I as defined in EN 301, and one method called C is suitable for adhesives of type II as defined in EN 301. The two methods A and B have a duration of two days and a half day respectively, and method C requires four days. All are suitable for every day quality control. 1 Scope This standard specifies three delamination methods for continuous quality control of the glue line integrity of glued laminated timber. 2 Normative references None. 3 Terms and definitions For the purposes of this European Standard the following terms and definitions apply: 3.1 delamination length sum of the lengths of delaminated glue lines on both end-grain surfaces of each test piece 3.2 glued laminated timber (glulam) structural member formed by bonding together timber laminations with the grain essentially parallel 4 Symbols b h l max,delam l glueline l tot,delam l tot,glueline 5 Requirements None. width of cross-section, in millimetres; depth of cross-section, in millimetres; maximum delamination length of one glue line in the test piece, in millimetres; length of one glue line, normally the width b shown in Figure 1, in millimetres; delamination length of all glue lines in the test piece, in millimetres; entire length of glue lines on the two end-grain surfaces of each test piece, in millimetres. 4

8 6 Delamination test of glue lines 6.1 Principle A gradient is introduced in the moisture content of the wood to build up internal stresses. This will result in tensile stresses perpendicular to the glue lines so that inadequate bonding quality will result in delamination of the glue lines. 6.2 Apparatus Pressure vessel A pressure vessel designed to withstand safely a pressure of at least 600 kpa (700 kpa absolute pressure) and a vacuum of at least 85 kpa (15 kpa absolute pressure), and equipped with pumps or similar device capable of giving a pressure of at least 600 kpa (700 kpa absolute pressure) and of drawing a vacuum of at least 85 kpa (15 kpa absolute pressure) Drying duct A drying duct where air is circulating at a velocity of 2 m/s to 3 m/s, and at a temperature and a relative humidity as given in Table 1. 5 Temperature Table 1 Climate in the drying duct for the different methods Method: A B C C 60 to to to 30 Relative humidity % < 15 8 to to Balance A balance capable of determining mass to an accuracy of 5 g Metal wedge and wooden hammer Metal wedge and wooden hammer capable of splitting open glue lines.

9 6.3 Preparation of test pieces The test pieces shall be prepared or selected in such a manner that they are representative of the production run. Each test piece shall be taken from a full cross-section of the laminated member to be tested, prepared by cutting perpendicular to the grain of the wood. It shall be (75 ± 5) mm in length (along the grain). The end-grain surfaces of the test piece shall be cut with a sharp saw or tool that produces a smooth surface. If the width b of the cross-section is greater than 300 mm the test piece may be split into two or more test pieces each at least 130 mm wide. If the depth h is greater than 600 mm the test piece(s) may be cut into two or more pieces each with a depth of at least 300 mm, see Figure 1. Key A Test piece b Width h High 6.4 Procedures General Figure 1 Test piece cut from a glulam member Dimensions in millimetres Before subjecting the test pieces to the test cycles, measure the total length in millimetres of glue lines on the end-grain surfaces of the test pieces. Subject the test pieces to the appropriate test cycle described in 6.4.2, or The number of test cycles shall be as given in Table 2. Table 2 Number of test cycles to be used in the different test methods Method: A B C Number of initial cycles Number of extra cycles An extra test cycle need only be carried out if the total delamination percentage according to is larger than the prescribed maximum value. 6

10 6.4.2 Measurement and evaluation of delamination The delamination measurement and the evaluation of the test pieces shall take place not later than 1 h after the final drying treatment. The total glue line delamination on both end-grain surfaces of the test pieces shall be measured in millimetres. NOTE 1 The use of a magnifying glass with a magnification of ca. 10 X and strong lighting are recommended to determine whether the opening in the glue line is a valid delamination or not. NOTE 2 A feeler gauge of 0,08 mm to 0,10 mm thick is convenient for probing into the joint to determine if separation in the glue line actually exists Consider the following glue line openings as being valid delaminations: a) a cohesive crack within the adhesive layer; b) a failure of the glue line precisely between the adhesive layer and the wood substrate. No wood fibres are left attached to the adhesive layer; c) a wood failure which is invariably within the first one or two layers of cells beyond the adhesive layer, in which the fracture path is not influenced by the grain angle and the growth-ring structure. It is characterized by a fine, woolly appearance of the wood fibres, which border the interface between the wood surface and the adhesive layer Do not regard the following glue line opening as delaminations: a) a solid wood failure which is invariably more than two cell layers away from the adhesive layer, in which the fracture path is strongly influenced by the grain angle and the growth-ring structure; b) isolated openings in the glue line which are less than 2,5 mm long and more than 5 mm away from the nearest delamination; c) openings in the glue line which are found along knots or resin pockets which border the glue line, or openings in the glue line which are caused by hidden knots in the glue line. When the cause of an opening in the glue line due to the presence of a knot is suspected, the glue line shall be opened with a wedge and hammer and be inspected for the presence of a concealed knot. Should the cause of the glue line opening be due to a concealed knot, the opening shall not be considered a delamination Test cycle for method A Place the test pieces in the pressure vessel and weigh them down. Admit water at a temperature of 10 C to 20 C in sufficient quantity so that the pieces are completely submerged. Separate the test pieces by stickers, wire screens, or other means in such a manner that all end-grain surfaces are freely exposed to the water. Draw a vacuum of 70 kpa to 85 kpa (i.e. an absolute pressure of 15 kpa to 30 kpa at sea level) and hold it for 5 min. Then release the vacuum and apply a pressure of 500 kpa to 600 kpa (600 kpa to 700 kpa absolute pressure) for 1 h. Whilst the test pieces are still completely immersed, repeat this vacuum pressure cycle making a two-cycle impregnating period requiring a total of 130 min Dry the test pieces for a period of between 21 h and 22 h in air at 60 C to 70 C and a relative humidity not greater than 15 %, and circulating at a velocity of 2 m/s to 3 m/s. During drying, the test pieces shall be placed at least 50 mm apart with the end-grain surfaces parallel to the stream of air. 7

11 6.4.4 Test cycle for method B Weigh and record to the nearest 5 g the mass of each test piece. Place the test pieces in the pressure vessel and weigh them down. Admit water, at a temperature of 10 C to 20 C in sufficient quantity so that the pieces are completely submerged. Separate the test pieces by stickers, wire screens, or other means in such a manner that all end-grain surfaces are freely exposed to the water. Draw a vacuum of 70 kpa to 85 kpa (i.e. an absolute pressure of 15 kpa to 30 kpa at sea level) and hold it for 30 min. Release the vacuum and apply a pressure of 500 kpa to 600 kpa (600 kpa to 700 kpa absolute pressure) for 2 h Dry the test pieces for a period of approximately 10 h to 15 h in air at 65 C to 75 C and a relative humidity of 8 % to 10 % and circulating at a velocity of 2 m/s to 3 m/s. During drying the test pieces shall be placed at least 50 mm apart with the end-grain surfaces parallel to the stream of air The actual time in the drying duct shall be controlled by the mass of the test pieces. Delamination shall be observed and recorded when the mass of the test pieces has returned to within 100 %-110 % of the original mass. Record the total drying time Test cycle for method C Place the test pieces in the pressure vessel and weigh them down. Admit water at a temperature of 10 C to 20 C in sufficient quantity so that the pieces are completely submerged. Separate the test pieces by stickers, wire screens, or other means in such a manner that all end-grain surfaces are freely exposed to the water. Draw a vacuum of 70 kpa to 85 kpa (i.e. an absolute pressure of 15 kpa to 30 kpa at sea level) and hold it for 30 min. Then release the vacuum and apply a pressure of 500 kpa to 600 kpa (600 kpa to 700 kpa absolute pressure) for 2 h. Whilst the test pieces are still completely immersed, repeat this vacuum pressure cycle giving a two-cycle impregnating period requiring a total of 5 h Dry the test pieces for a period of 90 h in air at 25 C to 30 C and a relative humidity in the range of 25 % to 35 %, and circulating at a velocity of 2 m/s to 3 m/s. During drying, the test pieces shall be placed at least 50 mm apart with the end-grain surfaces parallel to the stream of air. 6.5 Results General For each test piece the delamination percentages shall be calculated. If an extra cycle is performed calculate the results before and after the extra cycle Total delamination The total delamination percentage of a test piece shall be calculated from the following formula: l 100 l tot,delam tot,glueline Maximum delamination The maximum delamination percentage for a single glue line in a test piece shall be calculated from the following formula: l l max,delam glueline 8

12 6.6 Test report The test report shall include the following items: 9 a) reference to this European Standard; b) date of the test; c) identification of test pieces and members from which they have been cut. Any other relevant information, e.g. about preconditioning; d) species of timber; e) type of adhesive; f) test method (A, B or C); g) the total delamination percentage and the maximum delamination percentage after the prescribed number of cycles and any additional cycle that may be necessary; h) any relevant observation made during or after testing; i) signature of the person responsible for the testing.

13 BS EN 391:2002 BSI British Standards Institution BSI 389 Chiswick High Road London W4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0) Fax: +44 (0) BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0) Fax: +44 (0) Standards are also available from the BSI website at In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0) Fax: +44 (0) info@bsi-global.com. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0) Fax: +44 (0) membership@bsi-global.com. Information regarding online access to British Standards via British Standards Online can be found at Further information about BSI is available on the BSI website at Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0) Fax: +44 (0) copyright@bsi-global.com.

Licensed Copy: RRICTISQ RRICTISQ, ISO/Exchange Russia, 01 December 2004, Uncontrolled Copy, (c) BSI

Licensed Copy: RRICTISQ RRICTISQ, ISO/Exchange Russia, 01 December 2004, Uncontrolled Copy, (c) BSI BRITISH STANDARD BS EN 392:1995 Glued laminated timber Shear testof glue lines The European Standard EN 392:1995 has the status of a British Standard BSEN 392:1995 Committees responsible for this British