INSTALLATION MANUAL SFM2

Transcription

1 INSTALLATION MANUAL SFM2 Sony Electronics, Inc West Bernardo Drive San Diego, CA IN-SFM2.R1

2 Table of Contents WARNING STATEMENTS PARTS LIST INSTALLATION TOOLS INSTALLATION PROCEDURES SINGLE STUD INSTALLATION SOLID STRUCTURE INSTALLATION ATTACHING THE ADAPTER PLATE AND THE BACKPLATE COVER ATTACHING THE ADAPTER PLATE /BACKPLATE COVER TO THE DISPLAY ATTACHING THE DISPLAY TO THE BACKPLATE TECHNICAL SPECIFICATIONS WARRANTY CUSTOMER SUPPORT NOTES Page Installation Manual

3 Warning Statements WARNING: WARNING: WARNING: THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE (5) TIMES THE WEIGHT OF THE DISPLAY. IF NOT, THE WALL STRUCTURE MUST BE REINFORCED. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY. PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE. Indicates that the power plug is to be disconnected from the power outlet. Contact Sony Electronics with any questions. Safety precautions must be taken at all times. Warning and Caution statements. Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in damage to the display and/or damage to the mounting surface. Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the display and could increase the risk of fire. At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the plasma display. Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any surface other than wooden studs, use suitable hardware (which is commercially available). Installation Manual Page - 3 -

4 Parts List NOTE: This wall mount is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Sony Electronics (877) Adapter Plate (Qty 1) Ultra Flat Mount (Qty 1) M4 x 10mm Phillips Pan Head Screw (Qty 4) M6 x 12mm Security Screws (Qty 2) #10 x 1-1/4 Wood Screws (Qty 4) 6/32 x 1 Slotted Screw (Qty 2) M6 x 10mm Phillips Head Screws (Qty 4) #10 Anchors (Qty 4) For use with the following Sony models: SONY FWD-32LX1 FWD-32LX1R NOTE: Prior to installing the SFM2, the quick release sleeves (located on the back of the display) must be removed. After removing them, please store them in a safe location for possible future re-use. Installation Tools Phillips Head Screw Driver Portable Drill ¼ Drill Bit Level (Supplied) Soft Material/ Blanket Pencil Tape Measure Wrench with ½ Drive Socket Page Installation Manual

5 Installation Procedures Check that you have all the hardware listed in the parts list (Page 5). If any of the hardware described is missing, do not continue. Contact Sony Electronics immediately at (877) Separate the plates and choose the location for the monitor and follow any precautions listed in the LCD owners manual. Single Stud Installation 1. For single wood studs, use the two middle mounting points found on the back plate (Figure 1). 2. Locate the center of the wood stud behind the wall, mark the height and desired location. 3. Drill two 1/4 " pilot holes on the marked wall. 4. Secure the back plate to the center of the wood stud by using two (2) #10 wood screws (Figure 1). NOTE: Four wood screws will be used when mounting the backplate to a solid structure (Page 7). Also, all electrical wiring should be done at this time. Use the two (2) 6/32" x 1" handy box screws (supplied) for your installation needs. SFM2 Wooden Stud #10 Wood Screws Electrical Opening Frontplate #10 Wood Screw Figure 1 Installation Manual Page - 5 -

6 Solid Structure Installation 1. Use the four mounting points on the back plate (Figure 2). 2. Choose the wall where the monitor will be located. 3. Level and mark with a pencil the four (4) mounting points found on the back plate. 4. Drill four (4) 1/4" pilot holes for the plastic anchors then secure the wall bracket with the four (4) #10 x 1¼" screws (supplied) to the anchors. NOTE: All electrical wiring should be done at this time. Use the two (2) 6/32" x 1" handy box screws (supplied) for your installation needs. Solid Structure #10 Wood Screws #10 Wood Screws Electrical Opening Frontplate #10 Wood Screws #10 Wood Screws Figure 2 Page Installation Manual

7 Attaching the Adapter Plate and the Backplate Cover 1. Line up the mounting points (Figure 3). 2. Attach the frontplate to the adapter plate using four (4) M4 x 10mm Phillips Head screws (Figure 4). 3. Do not tighten the screws until all four are inserted. 4. Once the screws are inserted, tighten the screws down. CAUTION: Do not over tighten the M4 screws to the monitor. Failure to do so could result in damaging the threads and monitor. 5. At this time, loosely install the two (2) M6 x 12mm Security Screws (Figure 4). Adapter Plate Frontplate Figure 3. Mounting Box/ Adapter Plate Combination Installation Manual Page - 7 -

8 Adapter Plate M4 x 10mm Phillips Head Screws M4 x 10mm Phillips Head Screws Frontplate M6 x 12mm Phillips Head Security Screws Figure 4 Page Installation Instructions

9 Attaching the Adapter Plate /Backplate Cover to the Display 1. Place the display on a flat and soft surface and locate the four mounting points (Figure 5). 2. Attach the Adapter Plate to the back of the display using four (4) M6 x 10mm Phillips Head screws (Figure 6). Do not overtighten the screws. CAUTION: DO NOT OVERTIGHTEN THE SCREWS. Figure 5. Installing the Adapter Plate/ Mounting Box Adapter Plate Ultra Flat Mount Figure 6. Installation Complete Installation Instructions Page - 9 -

10 Attaching the Display to the Backplate NOTE: For clarity purposes, the following illustrations will be shown without the adapter plate and display attached. This must be done to show how the positioning of the backplate cover and the backplate relate to each other (connection-wise). 1. The flange opening must be facing up. 2. Raise the flat panel with the front plate attached and slide the top flange opening to the flange on the backplate (Figure 7). 3. Slide the monitor down slowly. Make sure the backplate flange captures the frontplate top flange opening before letting go of the monitor. Slide down and push in (Figure 8). 4. To secure the two plates, tighten the two (2) M6 x 12 (mm) security screws using a long Phillip head screwdriver (Figure 9). Flange Opening (Slot opening on top of frontplate) Flange Frontplate Backplate Figure 7 M6 x 12mm Security Screws Simulated Display Figure 8 Figure 9 Page Installation Manual

11 Technical Specifications Figure 7. Adapter Plate.750" VESA 100 VESA " " 5.750" Figure 8. Ultra Flat Mount Installation Manual Page

12 Warranty Limited Lifetime Warranty This product carries a limited lifetime warranty from ship date against defects in materials and workmanship. Sony Electronics is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. Customer Support In the event of missing and/or damaged equipment, or technical questions, the following information can help in the completion of the installation. Customer Service Notes Sony 2005 Sony Electronics, Inc West Bernardo Drive San Diego, CA (800) Page Installation Manual