PROTECTA Door Barrier
|
|
- Phebe Barker
- 6 years ago
- Views:
Transcription
1 MODEL NO: 320 PROTECTA Door Barrier ASSEMBLY INSTRUCTIONS INFA SECURE PTY LTD P.O. Box 487, Emu Plains NSW 2750 SERVICE NUMBER: (02)
2 INDEX I. Parts list for Door Barrier P 1 II. Door Barrier assembly instructions P 1-2 III. Methods of installing wall cups P 3 IV. Operating instructions P 3 V. Extension assembly instructions P 4 VI. How to release tube inserts P 4 VII. Safety notes & warnings P 5 IMPORTANT NOTES READ THIS CAREFULLY BEFORE INSTALLATION OF DOOR BARRIER 1 THE THREADED ROD (A) IS DESIGNED TO SLIDE FREELY INSIDE THE TUBE INSERTS (J). THE THREAD IS ONLY ACTIVE WHEN ADJUSTING WINDER KNOBS. 2 THE TWO MAIN FRAME UPRIGHTS (E) WILL ALSO HAVE A SLIGHT OUTWARDS POSITION BEFORE BEING PLACED IN POSITION. THIS IS DESIGNED TO GIVE REQUIRED TENSION WHEN IN POSITION.
3 PROTECTA Door Barrier #320 & Extensions #321/322/323/324/325/327 Manual I. PARTS LIST FOR DOOR BARRIER A J F D I J B E E H G J C J A) Threaded Pressure Pad 4PCS/Set B) Winder Knob 4PCS/Set C) Second Lock 1PCS/Set D) Lever Handle 1PCS/Set G) Cup 4PCS/Set H) Screw (To assemble G) 4PCS/Set A) Threaded Pressure Pad 4PCS/Set I) Locking Support Panel (Combined with E) E) Door Barrier Body 1PCS/Set J) Small Tube Insert 4PCS/Set II. DOOR BARRIER ASSEMBLY INSTRUCTIONS Step 1: Take the Door Barrier out of the carton. Remove the plastic bag. Step 2: Insert 4 (J) into the ends of the tubes.: Step 3: Place the threaded pressure pads (A) into the hole on each corner of the Door Barrier 1.
4 Step 4: Before installing the door barrier, measure the distance between the two surfaces to ensure that the Door Barrier is the correct width for the opening. Maximum measurement is 820mm If you find the measurement exceeds 820mm then two options need to be considered. A) Use a Protecta extension kit as illustrated in this leaflet (80, 140, 280, 490, 980 or 1490mm). Refer to section Method of Attaching Extensions before proceeding to Step5. B) Securely fit a wooden spacer on the wall side to fill the void. IMPORTANT: IT IS VERY IMPORTANT FOR YOUR BABY S SAFETY THAT THE MEASUREMENT BETWEEN THE OUTSIDE FRAME AND THE SURFACE WHERE THE DOOR BARRIER IS BEING PLACED DOES NOT EXCEED 65 MM. CHECK EACH SIDE. REFER TO FIGURE 2 65mm 65mm Figure 2 IMPORTANT NOTE: WALL CAPS (G) ARE ALWAYS RECOMMENDED TO BE USED FOR INCREASED SAFETY. ESPECIALLY WHEN THE WALL SURFACE HAS A SMOOTH FINISH IE, METAL SURFACES, HIGH-GLOSS PAINT ETC. See next page Methods of Installing Wall Cups. Step 5: Step 6: Place the Door Barrier in decided location, using your fingers, slide out the bottom threaded pressure pads (A) until they touch the wall surface and then tighten with winder knob (B) so the rubber pressure pad is firmly against the wall surfaces on each side. Ensure even measurement on both sides. NOTE: Refer to important note on Index page. Proceed to the top of the Door Barrier and slide out the threaded pressure pads (as in Step 5). With the leaver handle down, ensure the top of the rectangular metal upright (J) is located in recessed section of the lever handle (D). The metal upright should be almost touching the back of the recessed section. Remove the binding straps (H). 2.
5 Important Safety Checks 1). CHECK THE DOOR BARRIER IS FIRM AND SECURELY FITTED AGAINST THE WALL SURFACES. IF YOU FIND THE BARRIER MOVES ON THE SURFACES, THE PLASTIC CUPS (G) MUST BE USED. (AT THE TOP OF STAIRS OR IF USED ON AN EXTERIOR DOOR WE RECOMMEND ONLY TO USE THE WALL CUPS). REFER TO SECTION FITTING WALL CUPS BELOW 2). 3). ALWAYS CHECK THE 65mm MEASUREMENT IN IMPORTANT IN STEP 4 IS ADHERED TO. CHECK THAT THE DOOR BARRIER IS SITTING FIRMLY AGAINST THE SURFACE (RIGHT DOWN AGAINST THE FLOOR). III. METHODS OF INSTALLING WALL CUPS Reverse Step 5 and 6 on previous page and place cups (G) on the end of the rubber pressure pads. Wind the winder knobs until they push the cups against the wall surface. Trace around the cups then loosen the winder knobs and mark the center hole. Screws are provided to fix the cups to the wall. Screw the cups to the wall and repeat Steps 5 and 6. IV. OPERATING INSTRUCTIONS 1 Safety Button OPEN: Step 1: Push the safety button in and lift the handle in the direction shown as arrow (1) Step 2: Lift the gate as arrow (2) Step 3: Pull/push the door open 2 CLOSE: Step 1: Lift up the gate (D) and swing close. Once the gate is aligned correctly over the frame, lower in position Step 2: Push the lever handle (D) downward until the safety button locks into position. 3.
6 V. EXTENSION ASSEMBLY INSTRUCTIONS No mm No mm No mm No mm No mm No mm VI. HOW TO RELEASE TUBE INSERTS Pull out threaded presure pads as shown in diagram as shown in diagram. 4.
7 VII. SAFETY NOTES AND INSTRUCTIONS Suitable for use for babies and toddlers up to the age of 24 months. Check the size of opening is within recommended dimensions. Ensure that the walls are solid and rigid and have an even grease free surface. Partitions and plaster board walls may not be strong enough to support the gate without using wall cups. If so screw the wall cups in position with screws supplied so overtightening is not necessary. Always use under adult supervision. For extra security, especially at the top of stairs, we recommend the use of the wall cups supplied. When used on staircases, the gate should only be placed on the top or bottom stairs depending on the area that the child is being retained in. Install adjacent to that area. Figure 6 WARNINGS: FOR THE INCREASED SAFETY OF YOUR CHILD REPAIR YOUR DOOR BARRIER IF BROKEN OR DAMAGED BY AUTHORISED REPAIR AGENT. DO NOT USE UNTIL REPAIRED. CHECK THE DOOR BARRIER CONSTANTLY FOR LOOSE OR WORN PARTS AND REPAIR OR REPLACE PARTS AS NEEDED. ENSURE THAT THE DOOR BARRIER IS PROPERLY TIGHTENED AT ALL TIMES. NEVER ALLOW OLDER CHILDREN TO CLIMB THE DOOR BARRIER AS SERIOUS INJURY MAY OCCUR. ALWAYS FOLLOW THE INSTALLATION INSTRUCTIONS CAREFULLY AS THIS IS A SAFETY PRODUCT. ALWAYS INSTRUCT APPROPRIATE PERSONS WITH THE USE OF THIS PRODUCT. ALWAYS ENSURE THE DOOR BARRIER IS SECURELY FASTENED IN TIME OF USE. TO PREVENT SERIOUS INJURY OR DEATH, SECURELY INSTALL GATE OR ENCLOSURE AND USE ACCORDING TO MANUFACTURER S INSTRUCTIONS. NEVER USE WITH A CHILD ABLE TO CLIMB OVER OR DISLODGE THE GATE OR ENCLOSURE. NEVER LEAVE CHILD UNATTENDED. INSTALL WITH LOCKING MECHANISM ON ONE SIDE AWAY FROM CHILD. CHECK THAT THE DOOR BARRIER IS SITTING FIRMLY AGAINST THE SURFACE (RIGHT DOWN AGAINST THE FLOOR). 5.
8 INFA SECURE PTY LTD P.O. Box 487, EMU PLAINS NSW Old Bathurst Rd, EMU PLAINS NSW 2750 Service No: Fax: Infa Inquiries and Service (02) ISSUE: A w w w.infa-s e c u r e.com.au
EASY CLOSE WALK-THROUGH GATE
OWNER S MANUAL MODEL: 3030, 3036 EASY CLOSE WALK-THROUGH GATE WITH SMALL PET DOOR! READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE. www.carlsonpetproducts.com Carlson
More informationEXTRA TALL WALK-THROUGH GATE
OWNER S MANUAL MODEL: 0941, 0942 EXTRA TALL WALK-THROUGH GATE WITH SMALL PET DOOR! READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE. www.carlsonpetproducts.com Carlson
More informationHands Free Safety Gate
Hands Free Safety Gate OWNER S MANUAL MODEL: 1705 READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE. www.regalo-baby.com Regalo International, LLC. 3200 Corporate
More informationWARNING: Important: Keep these instructions for future reference. Gate Instructions (1) Assembly and Installation Instructions
Assembly and Installation Instructions Please read these instructions carefully. Please follow these instructions carefully to ensure that your gate extension is properly installed. Improper installation
More information149mm 210mm Design Paw Extra Wide & Extra Tall Walk-Thru Pet Gate With Small Pet Door MODEL NO: 1130 & 1140 Owner s Manual READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE
More informationMain Street Safety Gate
27930 Please read the following instructions carefully. Keep this instruction manual for future reference. Tools required: Phillips head screwdriver, drill (for top of stair installation), and pencil (not
More informationUnion Arch Safety Gate
33000 Please read the following instructions carefully. Keep this instruction manual for future reference. Tools required: Phillips head screwdriver, drill (for top of stair installation), and pencil (not
More informationDELUXE UNIVERSAL HEARTH GATE
DELUXE UNIVERSAL HEARTH GATE Model # 089420 IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY 01 Safety Precautions Read all instructions before assembly and use of the gate. Keep instructions for
More informationIMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY
URBAN 2 Tier Change Table # 092160 IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY Safety Precautions Read all instructions before assembly and use of the change table. Keep instructions for future
More informationOwner s Manual. Easy Close Gate
Owner s Manual Easy Close Gate MK0002-022 Rev 3 KEEP FOR FUTURE REFERENCE Please read the instructions carefully before installing this gate. For additional help, installation videos are available at www.munchkin.com
More information** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at:
3/01/2007 VISIT THE LITIME WEB SITE: WWW.LITIME.COM ** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 1 (800) 225-3865 Double Shed Doors for Back
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationReplacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)
Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the
More informationUNIVERSAL TWO TIER. Change Table Model # IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY
UNIVERSAL TWO TIER Change Table Model # 092103 IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY Safety Precautions Read all instructions before assembly and use of the change table. Keep instructions
More informationUSER GUIDE Crystal - Hardware Mount
USER GUIDE Crystal - Hardware Mount Height 30.7" (78 cm) Minimum Opening 29.5" (75 cm) Maximum Opening 39.75" (101cm) IMPORTANT: Qdos wants to keep your children safe and for that we need you to do your
More informationOWNER'S MANUAL. Please Do Not Return This Product To The Store!
MODEL NO. T8190SA TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be shipped inside
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationUSER GUIDE Crystal - Pressure Mount
USER GUIDE Crystal - Pressure Mount Height 30.3" (77 cm) Minimum Opening 30 (76 cm) Maximum Opening with 2 extensions (included) 37.8" (96 cm) Maximum Opening with 6 extensions 48.8" (124 cm) IMPORTANT:
More informationINSTRUCTION MANUAL DWX723-XE HEAVY-DUTY MITER SAW STAND FINAL PAGE SIZE : 8.5IN X 5.5IN
INSTRUCTION MANUAL DWX723-XE HEAVY-DUTY MITER SAW STAND FINAL PAGE SIZE : 8.5IN X 5.5IN DWX723-XE MITER SAW STANDS Components List A. Beam B. DW7231 Miter saw mounting brackets C. Extension arm D. DW7232
More informationUSER GUIDE Spectrum - Pressure Mount
USER GUIDE Spectrum - Pressure Mount Height 30 (76 cm) Minimum Opening 30 (76 cm) Maximum Opening with 2 extensions (included) 37 (94 cm) Maximum Opening with 6 extensions 48 (122 cm) IMPORTANT: Qdos wants
More informationMODEL 83 Pail Handler
MORSE MFG. CO., INC. 727 West Manlius Street P.O. Box 518 East Syracuse, NY 13057-0518 Phone: 315-437-8475 Fax: 315-437-1029 Email: service@morsemfgco.com Website: www.morsemfgco.com COPYRIGHT 2005 MORSE
More informationHigh Rise Sit-Stand Desk Converter
High Rise Sit-Stand Desk Converter Assembly Instructions for Model DC350 Patent No. 9,332,839 PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the video
More informationHome Accents Superwide Safety Gate
Home Accents Superwide Safety Gate OWNER S MANUAL MODEL: 1176 READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE. www.regalo-baby.com Regalo International, LLC. 3200
More informationAssemble and Adjustment Instructions and Flex Balance Beam and Crank Balance Beam
Sales & Service sasportonline.com Head Office 135 Forestview Road P.O. Box 40 Orillia, Ontario Canada L3V 6H9 Toll Free (800) 563-6479 Phone (705) 325-2274 Fax (705) 325-1485 USA Office 7879 Will Rogers
More informationSupergate III - Model 8615 (manual can be used for Pet Gate)
Supergate III - Model 8615 (manual can be used for Pet Gate) Dear Customer, Congratulations! You have just purchased what we feel is the best gate on the market. We are committed to making our products
More informationPlease Do Not Return This Product To The Store!
MODEL NO. T8176 QUICK SERVE 3000 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts may
More informationRetractable Gate IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE.
Retractable ate Fits openings up to 71 (1.8m) IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE. This product complies with safety standard ASTM F1004-10. AFTER SALES
More informationSAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20
SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management
More informationSupergate III - Model 8615 (manual can be used for Pet Gate)
Supergate III - Model 8615 (manual can be used for Pet Gate) Dear Customer, Congratulations! You have just purchased what we feel is the best gate on the market. We are committed to making our products
More informationPop-Out Slim Video Wall Mount
Installation Guide ADM-VWSP Pop-Out Slim Video Wall Mount CONTENTS Installation Safety Notes Page 2 Interface Adaptors Page 3 Installation Instructions Page 4 Installation Options Page 9 Alternative Mounting
More informationOWNER S MANUAL Table Tennis Table Patent Pending
OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8266
More informationO W N E R ' S M A N U A L
TABLE TENNIS TABLE MODEL NOS. T861 T861B O W N E R ' S M A N U A L 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may
More informationGraysen Manager s Chair Model # WC-666
LOT NUMBER: DATE PURCHASED: / / Graysen Manager s Chair ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES AS RECEIVED. If you have any questions regarding assembly or
More informationPlease Do Not Return This Product To The Store!
MODEL NOS. T8512 TOURNAMENT SERIES 3 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step. 2. Some smaller parts
More informationTable of Contents for Standard Duty Poly Blade Arctic Standard Duty Poly Blade 84" & 90" (Blade, Quadrant & T-frame)....2 Important note: Lift frames for this specific blade are listed below: Lift Frame
More informationASSEMBLY AND CARE INSTRUCTIONS JUST FOR KIDS 355
ASSEMBLY AND CARE INSTRUCTIONS VERSION: 8920100 (Revised 06/16) JUST FOR KIDS 355 SALES AND SERVICE spiethamerica.com Canada and International 135 Forestview Road, PO Box 40 Orillia, Ontario, Canada L3V
More informationElectric Skein Winder
Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers
More informationINSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1
INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1 IMPORTANT! : The MSP-S11 Mount is designed for use with Sharp 45" LCD displays that have a 200mm x 200mm mounting pattern. IMPORTANT! : The mount
More informationThanks for shopping with Improvements! Extra Tall Steel Slat Pet Gate with Alarm Item #441929
Thanks for shopping with Improvements! Extra Tall Steel Slat Pet Gate with Alarm Item #44929 To order, call -800-642-22 West Chester, OH 45069 063 If you have questions regarding this product, call -800-642-22
More informationTop Innovations, Inc. Innovative Products to Make Your Life Easier. Model SP-402 Owner s Manual
Top Innovations, Inc. Innovative Products to Make Your Life Easier Model SP-402 Owner s Manual THIS IS NOT A TOY! Adult supervision recommended Item contains sharp functional points and small parts Machine
More informationOB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount
INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More information#4500 BULLET SIZER & LUBRICATOR
#4500 BULLET SIZER & LUBRICATOR Assembly Your new #4500 Bullet Sizer and Lubricator has been fully assembled at the factory, However, to facilitate packaging and shipping, the handle has been dismounted.
More informationPlease Do Not Return This Product To The Store!
MODEL NOS. T81 TABLE TENNIS TABLE OWNER'S MANUAL 1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.. Some smaller parts may be shipped inside
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationS E L E C T I O N. Arm Curl. User manual
S E L E C T I O N T H E S T R E N G T H E V O L U T I O N User manual The identification plate of the and manufacturer, affixed behind the seat, gives the following details: A Name and address of the manufacturer
More informationINSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:
INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips
More informationROMAN AND. Roller Lift System Continuous Cord Loop GETTING STARTED BRACKET INFORMATION INSIDE MOUNT. A few simple tools are required:
ROMAN AND WOVEN WOOD SHADES Roller Lift System Continuous Cord Loop GETTING STARTED BRACKET INFORMATION A few simple tools are required: The brackets you received with your product are REQUIRED for proper
More informationINSTALLATION & OPERATING INSTRUCTIONS. REDCO LETTUCE KING I and LETTUCE KING IV
INSTALLATION & OPERATING INSTRUCTIONS for REDCO LETTUCE KING I and LETTUCE KING IV Lettuce King I Shown with optional Drum Ring Lettuce King IV TO BE SERVICED ONLY BY AUTHORIZED PERSONS P/N: 2802381 REV:
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationSales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd.
Sales & Service sasportonline.com SA Sport (Canada) SA Sport (U.S.A.) 135 Forestview Road 7879 Will Rogers Blvd. P.O. Box 40 Fort Worth, Texas Orillia, Ontario USA 76140 Canada L3V 6H9 Telephone: (705)
More informationINSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.
More informationS E L E C T I O N. Upper Back. User manual
and S E L E C T I O N T H E S T R E N G T H E V O L U T I O N User manual and and The identification plate of the and manufacturer, affixed to the frame on the side opposite the padded rest, gives the
More informationExtendable Swing Shut Gate
Extendable Swing Shut Gate WIDTH Adjustable from 72.5 to 95 cm HEIGHT Top of gate to floor 78 cm SPINDLES x 4 WALL CUPS x4 7cm EXTENSIONS x2 GATE NUTS x 4 SPANNER x Note: Each 7cm extension comprises of
More informationTELESCOPIC GATE MANUFACTURING AND INSTALLATION MANUAL.
TELESCOPIC GATE MANUFACTURING AND INSTALLATION MANUAL. Telescopic gates have been manufactured for many years essentially in the same way they are largely today. In recent years hardware suppliers have
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationThe wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist:
WICK REPLACEMENT The wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist: Slow to light, hard movement of the wick adjuster knob, kerosene odor
More informationThanks for shopping with Improvements! Wood Slat Pet Swing Gate Item #441937
Thanks for shopping with Improvements! Wood Slat Pet Swing Gate Item #441937 To order, call 1-800-642-2112 West Chester, OH 45069 0613 If you have questions regarding this product, call 1-800-642-2112
More informationPORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS
PORTA~TRACE GAGNE, INC. 41 Commercial Dr. Johnson City, New York 13790 Phone: 1-607-729-3366 Fax: 1-607-729-7644 ASSEMBLY INSTRUCTIONS PORTA~TRACE MODEL 2436T LIGHT TABLE PORTA~TRACE MODEL 3648T LIGHT
More informationAssembly Instructions Please keep for future reference Inspire 40
Assembly Instructions Please keep for future reference Inspire 40 Version 3 : 28/07/2014 Important - Please read these instructions fully before starting assembly ALR2902 Safety and Care Advice Important
More informationINSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays Models: FMA-220 and FMA-320
INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays The FMA-220 and FMA-320 pivot array allow both horizontal and vertical display pitch adjustment. The pitch adjustment range is 30 (15 up / 15
More informationWhalen Furniture Mfg. Factory No. 5 Page # 1
If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale Club Please call our customer service number and have your instructions and parts list
More informationFitSpine R.E.D. 5YEAR. Inversion Table Assembly Instructions WA R R A N T Y
R FitSpine R.E.D. Inversion Table Assembly Instructions TEETER HANG UPS 5YEAR WA R R A N T Y BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More information400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS
12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions
More informationSteele TV Stand Stock # BH
LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
More informationMaintenance Information
16601023 Edition 2 January 2014 Air Impact Wrench 2705P1 Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More informationSpeaker Mount Center Channel Speaker Adapter (PAC-301)
I N S T R U C T I O N M A N U A L Speaker Mount Center Channel Speaker Adapter () The Speaker Mount Center Channel Speaker Adapter () uses the same interface as the Side Speaker Adapter and can be used
More informationNancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual
Nancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual Thank you for purchasing our 4 Yard Option (4YO) Upgrade Kit. To install this upgrade you are simply going to assemble
More informationinstallation guide
JANUS INTERNATIONAL 1 866 562 2580 w w w. j a n u s i n t l. c o m 2000 2500 3000 installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 2000 2500 3000
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series
INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series This Instruction Manual covers most of the F-Series wall and desk mounts, as well as selected F-Series pole mounts. NOTE: Some F-Series
More informationPOP PLUS / SPIDER SET-UP INSTRUCTIONS
POP PLUS / SPIDER SET-UP INSTRUCTIONS 1 Place system frame on floor with screws indicating top. Expand upwards & outwards and secure frame connectors. Pop-Up display systems are made to be set-up and taken
More informationOPERATIONAL MANUAL V1.0. Removing/Replacing Blades
OPERATIONAL MANUAL V1.0 BLUEROCK WS-212 Wire Stripper Removing/Replacing Blades CAUTION!! IMPORTANT!! DANGER!! WARNING!! DISCONNECT MACHINE FROM POWER BEFORE PROCEEDING!! Estimated Completion Time: 90
More informationsouthpaw enterprises, inc.
southpaw enterprises, inc. Instruction Sheet C-STAND 7100 Store these instructions in a safe place or with the enclosed maintenance checklist Take time to familiarize yourself with the use and maintenance
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationJEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK004 / KRJW016T INSTALL TIME: 2 Hours NOTE: Your Jeep JK (3 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationTITAN INDUSTRIAL RACK 6-FOOT TALL / 4-SHELF
TITAN INDUSTRIAL RACK 6-FOOT TALL / 4-SHELF DXST10000 IMPORTANT: Please read this manual carefully before assembling this storage rack and save it for reference INSTRUCTION MANUAL 3 TABLE OF CONTENTS
More informationXceed ASSEMBLY MANUAL
Xceed ASSEMBLY MANUAL Table of Contents / Registration Congratulations on your commitment to fitness and your purchase of the Bowflex Xceed home gym. Before assembling your Bowflex Xceed home gym please
More informationRock, Roll n Ride Trike XLTM
Rock, Roll n Ride Trike XLTM Instructions Model Number: B9701 Rocking fun for littlest ones! Help toddlers roll along! Extra long handle for comfort. Remove handle for pedaling fun. Seat adjusts for growing
More informationTHIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE
Sal es@lambodoorscanada. com 2407A Kal adarave,ottawa,on K1V 8B9 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE 2 SHOCKS 565 PSI 2 SHOULDER
More informationSwing Gate Fits opening size 62cm to 102cm
Superior Swing ate Fits opening size 62cm to 102cm IMPORTANT! READ AND FOLLOW TESE INSTRUCTIONS CAREFULLY AND EEP FOR FUTURE REFERENCE This product complies with EN1930:2011 Standard. AFTER SALES SUPPORT
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-768) Jeep Cherokee 1997 2001 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationHD installation guide
JANUS INTERNATIONAL 1 866 562 2580 www.janusintl.c o m 1950 1950HD installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 1950 1950HD SHOWN A rolling
More informationSunset Swings By Health in Motion, LLC
Sunset Swings By Health in Motion, LLC Model 421 Lounge Swing Assembly and Operation Manual Record Serial Number Here www.sunsetswings.com by Health In Motion, LLC. 11/6/2009 421 Owners Assembly and Operation
More informationP.O. Box 8400 Green Bay, WI (920)
P.O. Box 8400 Green Bay, WI 54308-8400 (920) 468-2165 Change Notice No. 112 Implemented By: KI-Pembroke Notification By: Scott Vissers Date: 03/15/10 Component Product Title: Series XXI Lateral Filing
More informationCORVETTE CORVETTE REV: Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending.
CORVETTE 2005-2006 CORVETTE 2005-2007 REV: 7-2-07 Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending. Page 1 of 12 CORVETTE C6 2005-2007 THIS KIT INCLUDES:
More informationOnBoard Bass Drum/Gong Cart
Assembly and Owner s Manual OnBoard Bass Drum/Gong Cart CONTENTS Important User Information...................................................................2 Safety...................................................................................3
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationAssembly Instructions Signature Choral Riser 4-Step Model
Assembly Instructions Signature Choral Riser 4-Step Model Contents Important User Information...........................2 General...2 Manufacturer...2 Intended Use...2 Warranty...2 Safety Precautions.................................3
More informationHardware and Components:
Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut
More informationREV: 1.2 TRAMPOLINE MANUAL
REV: 1.2 TRAMPOLINE MANUAL TRAMPOLINE PARTS LIST: Item 8FT 10FT 12FT 14FT 16FT A 1 1 1 1 1 B 1 1 1 1 1 C 6 8 12 12 12 E 48 64 72 96 108 F 6 8 12 12 12 G 3 4 6 6 6 H 12 16 24 24 24 I 1 1 1 1 1 DIAGRAMS
More informationw w w. h d o n l i n e s h o p. d e VRSCF RIGID SADDLEBAGS GENERAL PREPARATION -J04704 REV Kit Number Models Tools and Supplies Required
-J070 REV. 00-0- VRSCF RIGID SADDLEBAGS GENERAL Kit Number 7-0 Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English
More informationBunk Pod Front Entry Assembly Instructions
Bunk Pod Front Entry Assembly Instructions www.podtime.co.uk enquiries@podtime.co.uk Working House Ltd How to assemble your pod This step by step guide will show how to assemble your pod(s) on site. It
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK002 / KRJW014T INSTALL TIME: 5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationMM750 Installation Instructions
MM750 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on
More informationKawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions.
Owner s Manual Model: Kawasaki Teryx 750 Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware
More informationChin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets. Contents
Chin Strap Chin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets Contents BTM-1 1.1 Chin Strap BTM-4 1.2.3.1 Preparation BTM-1 1.1.1 Chin Strap Removal BTM-4 1.2.3.2 Disassembly BTM-1 BTM-2
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More information2 ADULTS REQUIRED FOR ASSEMBLING
2 ADULTS REQUIRED FOR ASSEMBLING If you have any questions regarding assembly or if you are missing parts, do not return this item to Retailer Store Please call our customer service number and have your
More informationTP4463. ASSeMBly INSTruCTIONS FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3
TP63 FLAT PANEL TV MOUNTING SYSTEM OPTION 1 OPTION 2 OPTION 3 Flat Panel TV Stand Stand with TV Mounting System Stand with Wall Mount ASSeMBly INSTruCTIONS for your safety, please follow these precautions:!
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More information