3 POINT HITCH LOGSPLITTER

Transcription

1 3 POINT HITCH LOGSPLITTER OPERATOR S MANUAL AND PARTS LIST

2

3 TABLE OF CONTENTS SECTION PAGE 1. GENERAL INFORMATION 1 2. SAFETY GUIDELINES DEFINITIONS SAFE OPERATING PROCEDURE 3 3. LOG SPLITTER ASSEMBLY 3 4. LOG SPLITTER STARTUP POINT HITCH LOG SPLITTER ASSEMBLY 16 TON 6 1. GENERAL INFORMATION Congratulations on your choice of Princess Auto Log Splitter. This equipment has been designed and manufactured to meet the needs for commercial and private log splitting use. All structural parts are designed from high quality steel, and all power pack items are selected specifically to meet your industrial and consumer needs. Safe, efficient and trouble free operation of your Log Splitter requires that you and anyone else using the Log Splitter read and understand all of the safety, operation maintenance and troubleshooting information contained within this Operator s Manual. WARRANTY- PARTS - SERVICE If you experience any problems and need assistance or parts and repair service please contact Princess Auto Ltd. at: Telephone # Fax # To obtain prompt, efficient service, always provide the serial number and item number of your unit. See the parts list for location of the serial number decal. Please mark the numbers in the space provided for easy reference. SERIAL # ITEM # Printed in Canada Issue Date: JULY 2008 Revision 0 1

4 2. SAFETY GUIDELINES 2.1 DEFINITIONS Safety symbols identify important safety messages that alert to the possibility of personal injury or death. Review them carefully before operating the unit and before performing maintenance or repairs. Check the rules and regulations at your location and identify possible hazards. The appropriate signal word for each message has been selected using the following guide - lines: - Danger indicates an immediate and specific hazard, which will result in severe personal injury or death if the proper precautions are not taken. - Warning indicates a specific hazard or unsafe practice, which could result in severe personal injury or death if proper precautions are not taken. - Caution indicates potentially hazardous situation, which may result in minor or moderate injury if proper practices are not taken. IMPORTANT SAFETY INSTRUCTIONS Read and understand operator s manual and all safety alerts before operating or maintaining your Log Splitter. Be certain that everyone operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the safety precautions. Never let children or untrained adults operate the machine. RISK OF HOT SURFACES Contact with hot surfaces, such as engines exhaust components could result in serious burn. RISK OF FLUID INJECTION Make sure all hydraulic components are maintained in good condition. Replace kinked, cracked or otherwise damaged hydraulic components or hoses. Do not check for leaks with your hands, use wood or cardboard as a backstop instead. Escaping fluid under pressure can have sufficient force to penetrate the skin causing serious personal injury or even death. If hydraulic fluid penetrates the skin, seek medical attention immediately. A serious infection or reaction will develop. Wear proper eye protection when searching for a high-pressure hydraulic leak. Do not remove the cap from the hydraulic reservoir while log splitter is running. Hot oil under pressure could result in serious injury. 2

5 2.2 SAFE OPERATING PROCEDURE Read and understand the Operator s Manual completely before using your log splitter. Do not allow anyone to operate your log splitter who has not read the Operator s Manual or who has not been instructed on the safe operation of your log splitter. Always adjust Lift Arm to the appropriate 3pt. Hitch category before attaching log splitter to 3 pt. Hitch. Never allow children or un-trained adults to operate your log splitter. If a helper is assisting in loading or un-loading logs ensure they are clear of the working area when actuating the controls. Always keeps hands, clothing or other body parts clear of moving parts. Never place hands, clothing or other body parts between the splitting knife and the log, or the log and base end of the splitter beam during operation. Never allow anyone to ride on your log splitter. Never transport cargo on your log splitter. Never attempt to load the log splitter when the knife is in motion. Always use your hand to operate the control lever. Never use another body part, rope or any extension device to operate the control lever. Always wear safety glasses/goggles, shoes or boots, gloves and hearing protection. Always keep fingers away from cracks that may occur in logs. Your log splitter is only intended for splitting wood. Do not use it for other purposes. Never alter the log splitter or any part of its manufactured design. 3. LOG SPLITTER ASSEMBLY The log splitter is shipped in a crate and requires assembly before it can be used. Parts are heavy; ensure you have someone to assist you with the assembly. Proper safety measures must be applied to avoid injury. 1. Select an area that is firm and dry with sufficient space to work around all sides of the unit. 2. Carefully remove the lid from the crate. Inspect the contents of the shipping crate to ensure all of the components for your Log Splitter model are within. If there are any missing or damaged components contact your local Princess Auto store or Customer 3

6 Service at either: Telephone # Fax # Install cylinder to main frame assembly. Ensure that the cylinder is flush against the flange plate, parallel to the I-beam surface. Leave flange bolts loose till cylinder is connected to knife assembly. 4. Loosely assemble Knife onto the Main Beam. Completely thread the Cylinder Clevis onto the Cylinder Shaft. With the Cylinder fully extended, check alignment of Cylinder Rod with coupler of the Knife. Slide the Knife assembly into the Cylinder Clevis and secure Knife assembly. 5. Tighten Cylinder bolts, then tighten all Knife assembly bolts. 6. Install Lift Arm Assembly, and Top Link Bracket 7. When mounting to tractor, tractor should be turned off and in park. 8. Install lift arms first to the 3 pt. hitch ensuring that lift arm pins are secure with retaining pins. 9. Connect Top Link Bracket to tractor, adjust the tractor s top link arm to connect the top link bracket, do not lift up log splitter, use adjustments on tractor to insert top link pin and retaining pin. 10. Adjust lift arms to ensure that the log splitter beam is horizontal, not leaning to one side; the logs must be able to sit firmly on the beam. *For tractors under 25 hp front wheel weights are recommended. 4. LOG SPLITTER STARTUP 1. Ensure Log splitter is parallel with ground. Clear the area of people, especially small children. Keep the tractor at least 6 ft. away from buildings, obstructions and flammable objects. 2. Check all fasteners and fittings for tightness. Inspect hydraulic hoses for wear, cracking or fatigue. Replace if damaged. 3. Add hydraulic oil to tractor reservoir. (Available at Princess Auto stores). Use a quality mineral based hydraulic fluid, a viscosity in the SUS range and operating temperature is recommended. ISO grade 32 would work well for the majority of applications. 4. Cycle the cylinder at least three times with no load to fill the system with oil and bleed the system of air. 5. Stop the engine and add more hydraulic oil if necessary. 6. Your Log Splitter should now be ready for operation. 4

7 5

8 5. LOG SPLITTER 3 POINT HITCH ASSEMBLY 16 TON ITEM #

9 LOG SPLITTER 3 POINT HITCH 16 TON ITEM # Item # PART # DESCRIPTION QTY #8 ORB MALE X 1/2 JIC MALE ELBOW /2 HOSE, 2 WIRE X 22 LG /3000psi / FITTINGS: FJIC-08 / FJIC /2 HOSE, 2 WIRE X 96 LG /3000psi / FITTINGS: 1/2 NPTF SWL / 1/2 NPTM SWL /2 INCH DUST CAP FOR MALE QUICK ATTACH FITTING BOLT HEX UNC X 2.00LG GR 5 PTD BOLT HEX UNC X 2.50 LG BOLT HEX UNC X 2.75 LG BOLT HEX UNC X 3.50 LG BOLT HEX 1.0 X 4.5 LG UNC CLEVIS ROD 1.50 UNF 1.00 DIA CONNECTOR 08 MALE ORB X 08 MALE NPT CYL 4024 LOGSPLITTER DECAL KEEP HANDS CLEAR DECAL PAL SERIAL # DECAL POWERFIST 16 TON LOG SPLITTER ELBOW.50 JIC X.50 NPTM BRASS ELBOW MALE NPT X 12 MALE NPT HOUSING ASSEMBLY KNIFE ASM - 3PT HITCH MAIN FRAME ASM NUT LOCK 1.0 UNC NUT LOCK UNITORQ UNC PIN HITCH.625 X 4.50 EFFECT LENGTH PIN LIFT ARM.875 DIA X 1.75 LG TYPE A PIN TOP LINK PLATE KNIFE BACKING PLATE KNIFE SPACER-3PT HITCH QUICK ATTACH NIPPLE MALE, 08 FEMALE NPT ON FRONT SUPPORT ARM, LH SUPPORT ARM, RH SWIVEL CONNECTOR 08 FEMALE NPT X 08 MALE NPT TOP LINK, 3 PT HITCH LOGSPLITTER VALVE LOGSPLITTER 2500 PSI WASHER PTD.531 ID X OD X.095 THK 4 7