Adhesives, Solvents & Abrasives HIT. Part Number

Transcription

1 , Glue s Non-Flammable, No VOC s Strong Permanent Bonds No Chlorinated Water Resistant Cost Effective, High Coverage Rate No ODS (Ozone Depleting Substances) LEED Compliant is a versatile, high performance water based industrial contact adhesive is water resistant and temperature resistant to above 200 F is designed for bonding decorative laminates to particleboard but may also be used on a variety of other substrates including veneers, foam, headliners, glass and mirrors, cork, tile, fiberglass and plastics. The aerosol system reduces application cost by saving time and material is designed to be applied to the two surfaces about to be joined. Spray an even coating of adhesive to cover the surfaces. Allow to dry completely and become tacky. Typical dry times are minutes, which can be speeded up with hot air, infrared or forced air heaters. Dry completely before bonding parts together. For porous surfaces and crucial areas such as edgebanding, applying a second coat after the first has become tacky is recommended. Place the coated surfaces together and apply a uniform pressure for strongest bonding. Full adhesive strength will be reached in 24 hours. and substrates should be at 60 F or higher for best results. Insure that surfaces are dry and free from dirt, grease, oils and any other solvents. SHELF LIFE: 6 months FLAMMABILITY: Non-Flammable per standard industry flame projection test. STORAGE: Protect from freezing. Return to room temperature prior to use. For canister product keep cylinders off the floor at all times when temperature is below 60 F. White when wet clear when dry Glue % solids: 50 52% 1.07 to 1.11 gms/cc (8.9 to 9.3 lbs/gal) Shear Adhesion: > 100 psi Shear Adhesion Failure Temp (SAFT): > 200 F Flash Point none 9# Disposable Canister 30# Disposable Canister *Special Order Order Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warrantyis made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a High Temperature High Strength Water Based See Material Safety Data Sheet for Proper Handling and Safety Information REV 08/05 434

2 Glue, SHELF LIFE: 6 months FLAMMABILITY: Non-Flammable Liquid STORAGE: Protect from freezing. Return to room temperature prior to use. For canister product keep cylinders off the floor at all times when temperature is below 60 F. White when wet clear when dry Glue % solids: 50 52% 1.07 to 1.11 gms/cc (8.9 to 9.3 lbs/gal) Shear Adhesion: > 100 psi Shear Adhesion Failure Temp (SAFT): > 200 F Flash Point none : 5 gal Pail : 55 gal Drum Non-Flammable, No VOC s Strong Permanent Bonds No Chlorinated Water Resistant Cost Effective, High Coverage Rate No ODS (Ozone Depleting Substances) LEED Compliant , is a versatile, high performance water based industrial contact adhesive are water resistant and temperature resistant to above 200 F is designed for bonding decorative laminates to particleboard but may also be used on a variety of other substrates including veneers, foam, headliners, glass and mirrors, cork, tile, fiberglass and plastics. The aerosol system reduces application cost by saving is designed to be applied to the two surfaces about to be joined. Spray an even coating of adhesive to cover the surfaces. Allow to dry completely and become tacky. Typical dry times are minutes, which can be speeded up with hot air, infrared or forced air heaters. Dry completely before bonding parts together. For porous surfaces and crucial areas such as edgebanding, applying a second coat after the first has become tacky is recommended. Place the coated surfaces together and apply a uniform pressure for strongest bonding. Full adhesive strength will be reached in 24 hours. and substrates should be at 60 F or higher for best results. Insure that surfaces are dry and free from dirt, grease, oils and any other solvents. Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warrantyis made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a High Temperature High Strength Water Based s See Material Safety Data Sheet for Proper Handling and Safety Information REV 08/05 435

3 , Glue s Fast Tack, Strong Bonds Water Resistant No ODS (Ozone Depleting Substances) Temperature Resistant to over 200 degrees F Aerosol is a versatile, high performance industrial contact adhesive. It is water and temperature resistant to above 200 degrees F is designed for bonding decorative laminates to particleboard but may also be used on a variety of other substrates including veneers, fabarics, upholstery, foam, headliners, glass and mirrors, cork, tile, fiberglass and plastic. The aerosol system reduces application cost by saving time and material SHAKE WELL BEFORE USING Contact Spray Adhesive is designed to be applied to the two surfaces about to be joined. Spray an even coat of adhesive to cover 80% to 100% of the surfaces. Do not wet the surface. Allow to dry 2 to 4 minutes and become tacky. For porous surfaces and crucial areas such as edgebanding, it is recommended applying a second coat after the first has dried and become tacky. Place the coated surfaces together and apply a uniform pressure for strongest bonding. Full adhesive strength will be reached in 24 hours. Please note that adhesives and substrates should be at 60 F or higher for best results. Also, insure that surfaces are dry and free from dirt, grease, oils and any other solvents. SHELF LIFE: 1 Year FLAMMABILITY: Flammable per standard industry flame projection test. STORAGE: Not damaged by freezing. Return to room temperature prior to use. Strong Solvent Odor, Clear Color Solvent: Methylene Chloride 0.83 to 0.87 gms/cc (6.9 to 7.3 lbs/gal) Shear Adhesion: >100 psi Shear Adhesive Failure Temp (SAFT): > 200 degrees F Volatile Organic Compounds <410 gm/liter 15 oz aerosol Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warranty s Contact Spray Adhesive Aerosol is made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a 436

4 Glue, s Safe, Biodegradable Pleasant Citrus Odor No Methylene Chloride No chlorinated solvents No ODS (Ozone Depleting Substances) Citrus Adhesive Cleaner / Remover will cut through and remove adhesive products. This cleaner utilizes strong citrus oil solvents which not only clean but leave a pleasant citrus aroma. Works well on over-spray, squeeze out and for equipment clean-up. SHAKE WELL BEFORE USING Adhesive Remover is designed to remove adhesives, wet or dried from unwanted areas. Spray on and allow 3 to 5 minutes contact time for best performance. Allow cleaner to completely evaporate before applying new adhesive. Also works well on removing other materials: grease, oil, stickers, decals, tar. SHELF LIFE: 6 months FLAMMABILITY: Flammable per standard industry flame projection test. STORAGE: Not damaged by freezing. Return to room temperature prior to use. Citrus odor,clear Solvent Base: Solvent mixture.73 to.77 gms/cc (6.0 to 6.4 lbs/gal) Volatile Organic Compounds <745 gm/liter % Volative 100% 14 oz aerosol Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warrantyis made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a s Citrus Adhesive Remover See Material Safety Data Sheet for Proper Handling and Safety Information REV 08/05 437

5 , Glue s Fast Tack, Strong Bonds Will Not Attack Polystyrene Water Resistant Cost Effective, High Coverage Rate No Chlorinated No ODS (Ozone Depleting Substances) is a versatile, high performance industrial contact adhesive. The adhesive is water resistant and designed specifically for bonding expanded polystyrene. It may also be used on a variety of other substrates including fabrics, upholstery, foam, cork and some plastics. The aerosol system reduces application cost by saving time and material is designed to be applied to the two surfaces about to be joined. Spray an even coat of adhesive to cover 80% to 100% of the surfaces. Do not wet the surface. Allow to dry 3 to 5 minutes and become tacky. For porous surfaces and crucial areas such as edgebanding. It is recommended that a second coat be applied after the first has become tacky. Place the coated surfaces together and apply a uniform pressure for strongest bonding. Full adhesive strength will be reached in 24 hours. Please note that adhesive and substrates should be at 60 degrees F or higher for best results. Also insure that surfaces are dry and free from dirt, grease, oils and any other solvents. SHELF LIFE: 1 Year FLAMMABILITY: Flammable per standard industry flame projection test. STORAGE: Not damaged by freezing. Return to room temperature prior to use. For canister products keep cylinders off floor when temperature is below 60 degrees F. Clear or Green Solvent Base: Hexane, Acetone.68 to.72 gms/cc (5.6 to 6.0 lbs/gal) Glue % s: 28-33% Shear Adhesion: Expanded Polystyrene fails before bond. 13 oz aerosol Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warranty is made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a s Expanded Polystyrene Adhesive See Material Safety Data Sheet for Proper Handling and Safety Information REV 08/05 438

6 Glue, s Fast Tack, Strong Bonds Water Resistant No ODS (Ozone Depleting Substances) Temperature Resistant to over 200 degrees F Canister is a versatile, high performance industrial contact adhesive. It is water and temperature resistant to above 200 degrees F is designed for bonding decorative laminates to particleboard but may also be used on a variety of other substrates including veneers, fabrics, upholstery, foam, headliners, glass and mirrors, cork, tile, fiberglass and plastic. The aerosol system reduces application cost by saving time and material. SHAKE WELL BEFORE USING Contact Spray Adhesive is designed to be applied to the two surfaces about to be joined. Spray an even coat of adhesive to cover 80% to 100% of the surfaces. Do not wet the surface. Allow to dry 2 to 4 minutes and become tacky. For porous surfaces and crucial areas such as edgebanding, it is recommended applying a second coat after the first has dried and become tacky. Place the coated surfaces together and apply a uniform pressure for strongest bonding. Full adhesive strength will be reached in 24 hours. Please note that adhesives and substrates should be at 60 F or higher for best results. Also, insure that surfaces are dry and free from dirt, grease, oils and any other solvents. SHELF LIFE: 1 Year FLAMMABILITY: Flammable per standard industry flame projection test. STORAGE: Not damaged by freezing. Return to room temperature prior to use. Strong Solvent Odor, Clear or Red in Color Solvent: Methylene Chloride 0.83 to 0.87 gms/cc (6.9 to 7.3 lbs/gal) Shear Adhesion: >100 psi Shear Adhesive Failure Temp (SAFT): > 200 degrees F Volatile Organic Compounds <450 gm/liter 37.5# 11# Disposable Canister, 37.5# Disposable Order Number Canister Returnable Canister, 375# *Special Returnable Order* Canister 375# Returnable Canister *Special Order* Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warranty is made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a s Contact Spray Adhesive 439

7 , Glue s Use freshly machined stock with moisture content of 6 to 8%. Apply with brush, roller or roll spreader to one side of stock to be glued. Spread rates per thousand square feet single glue line: ing 25 to 40 lbs; Wood 35 to 55 lbs; High Pressure 25 to 35 lbs. Assembly time is 5 to 15 minutes depending on temperature, moisture content, species and porosity. Pressing / Clamping 30 to 45 minutes at: 35 to 50 psi for laminate 75 to 100 psi for veneer 75 to 200 psi for solid wood or edge gluing Dead stack overnight before machining. Use polyethylene, aluminum or fiberglass containers. Avoid contact with iron. SHELF LIFE: 6 months FLAMMABILITY: Non-Flammable liquid STORAGE: Protect from freezing. Return to room temperature prior to use. For canister product keep cylinders off the floor at all times when temperature is below 60 F. Solvent Base: Shear Adhesion: Flash Point : 1 gal Pail : 5 gal Pail Non-Flammable, Water Based Excellent for For General Wood Repairs Fast Setting, Superior Strength Cost Effective, High Coverage Rate White when wet clear when dry Water 1.08 to 1.12 gms/cc (9.0 to 9.4 lbs/gal) > 100 psi >200 degrees F , are water-based white glue used as a general purpose adhesive for edge or face gluing of hardwoods, softwoods, general assembly, panel on frame, doweling and laminating of veneer or high pressure laminate. Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warrantyis made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a s High Quality White Wood Glue See Material Safety Data Sheet for Proper Handling and Safety Information REV 08/05 440

8 Glue, SHELF LIFE: 6 months FLAMMABILITY: Non-Flammable liquid STORAGE: Protect from freezing. Return to room temperature prior to use. For canister product keep cylinders off the floor at all times when temperature is below 60 F. Solvent Base: Shear Adhesion: Flash Point : 1 gal Pail : 5 gal Drum Yellow when wet clear when dry Water 1.08 to 1.12 gms/cc (9.0 to 9.4 lbs/gal) > 100 psi >200 degrees F Non-Flammable, Water Based Excellent for For General Wood Repairs Fast Setting, Superior Strength Cost Effective, High Coverage Rate , are water-based white glue used as a general purpose adhesive for edge or face gluing of hardwoods, softwoods, general assembly, panel on frame, doweling and laminating of veneer or high pressure laminate. Use freshly machined stock with moisture content of 6 to 8%. Apply with brush, roller or roll spreader to one side of stock to be glued. Spread rates per thousand square feet single glue line: ing 25 to 40 lbs; Wood 35 to 55 lbs; High Pressure 25 to 35 lbs. Assembly time is 5 to 15 minutes depending on temperature, moisture content, species and porosity. Pressing / Clamping 30 to 45 minutes at: 35 to 50 psi for laminate 75 to 100 psi for veneer 75 to 200 psi for solid wood or edge gluing Dead stack overnight before machining. Use polyethylene, aluminum or fiberglass containers. Avoid contact with iron. Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warranty is made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a s High Quality Yellow Wood Glue s See Material Safety Data Sheet for Proper Handling and Safety Information REV 08/05 441

9 , Glue s Fast Tack, Strong Bonds Non-Flammable Adhesive Cost Effective, High Coverage Rate No ODS (Ozone Depleting Substances) Temperature Resistant to over 200 Degrees F is a versatile, high performance industrial contact adhesive is water resistant and temperature resistant to above 200 F is designed for bonding decorative laminates to particleboard but may also be used on a variety of other substrates including veneers, foam, headliners, glass and mirrors, cork, tile, fiberglass and plastics. The aerosol system reduces application cost by saving time and material is designed to be applied to the two surfaces about to be joined. Spray an even coating of adhesive to cover the surfaces. Allow to dry 2-5 minutes and become tacky. For porous surfaces and crucial areas such as edgebanding, applying a second coat after the first has become tacky is recommended. Place the coated surfaces together and apply a uniform pressure for strongest bonding. Full adhesive strength will be reached in 24 hours. and substrates should be at 60 F or higher for best results. Insure that surfaces are dry and free from dirt, grease, oils and any other solvents. SHELF LIFE: 1 Year FLAMMABILITY: Non-Flammable per standard industry flame projection test. STORAGE: Not damaged by freezing. Return to room temperature prior to use. For canister product keep cylinders off the floor at all times when temperature is below 60 F. Clear or red Glue % solids: 25-28% 1.16 to 1.20 gms/cc (9.6 to 10 lbs/gal) Shear Adhesion: > 100 psi Shear Adhesion Failure Temp (SAFT): > 200 F 11# Disposable Canister 37.5# Disposable Canister 375# Returnable Canister *Special Order* *Special Order* Order Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warrantyis made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a High Temperature High Strength Non-Flammable Adhesive See Material Safety Data Sheet for Proper Handling and Safety Information REV 08/05 442

10 Glue, SHELF LIFE: 1 Year FLAMMABILITY: Non-Flammable per standard industry flame projection test. STORAGE: Return to room temperature prior to use. For canister product keep cylinders off the floor at all times when temperature is below 60 F. Solvent Base: % s 12-15% Shear Adhesion: > 100 psi Flash Point None 5 gal Drum 55 gal Drum Non-Flammable Exceptional Green Strength Excellent Spray Characteristics High Head Resistance High Heat resistant Spray Grade Contact Adhesive has been specifically formulated for use in bonding a wide variety of materials, including, decorative laminates, metals (not copper), plywood, particleboard, formed polystyrene, polyurethane foam and rigid plastics. The consistency of provides easy and uniform spray coverage for all types and sizes of operations. Its high tack plus excellent combinability and green strength provide uniform high strength bonds under a wide variety of laminating conditions. s to be bonded must be dry and clean. Adhesive and surface should be a 65 o F or higher. Apply an even coat of adhesive to both surfaces. Use a brush, roller or adhesive spreader. Both coated surfaces must be allowed to dry before bonding. This will take from minutes under normal conditions. When dry, the adhesive will adhere but not transfer to the finger if touched. If adhesive becomes too dry (over 1 hour) it may be reactivated by applying another coat of adhesive. Bring both surfaces into contact to exact position desired. Contact adhesive bonds instantly on contact and work cannot be shifted into place. Apply pressure to the entire surface. Pressure should be applied from center toward the edges to prevent air entrapment and to ensure positive contact. Work pieces can be handled or machined immediately after bonding. The bond actually grows stronger with age. Excess and over-coated adhesive may be cleaned off tools and laminate surfaces with appropriate reducer/cleaner. Stir thoroughly before use. Sweet pungent odor, natural clear or red in color Compound Neoprene 126 to 1.30 gms/cc (10.5 to 10.9 lbs/gal) Order *Special Order* Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warrantyis made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a s Non-Flammable, High Heat Spray Grade Contact Adhesive s See Material Safety Data Sheet for Proper Handling and Safety Information REV 08/05 443

11 , Glue s Non-Flammable Excellent Green Strength High s Formulation is a High s Spray Grade Contact Adhesive that has been specifically formulated for use in areas where flammability is an issue is a contact adhesive with exceptional tack and shear strength, high heat and UV stability, water resistance, fast drying, precise application control and long open time is designed to be applied to the two surfaces about to be joined. Spray an even coating of adhesive to cover 80 to 100% of the surfaces. Do not wet the surface. Allow to dry 3-5 minutes and become tacky. For porous surfaces and crucial areas such as edgebanding, it is recommended applying a second coat after the first has become tacky. Place the coated surfaces together and apply a uniform pressure for strongest bonding. Please note that adhesives and substrates should be at 60 degrees F or higher for best results. Also, insure that surfaces are dry and free fr om dirt, grease, oils and any other solvents is great for bonding a wide variety of materials, including, but not limited to decorative laminates, metals (except copper), plywood, particleboard, polyurethane foam and rigid plastics. The consistency of provides easy and uniform spray coverage, in all types and sizes of operations. It's high solids formulation provides good green strength and uniform high strength bonds under a wide variety of laminating conditions. SHELF LIFE: 1 Year FLAMMABILITY: Non-Flammable Liquid STORAGE: Not Harmed by Freezing. Return to room temperature prior to use. Strong Solvent Odor, Clear, Red or Green in Color Base: Synthetic Rubber Solvent: Methylene Chloride Glue % solids: 28-32% 1.17 to 1.21 gms/cc (9.7 to 10.1 lbs/gal) Flash Point none 5 gal Pail 55 gal Drum Manufacturer and distributor of this product make no warranty, express or implied, including, but not limited to any implied warranty of fitness for a particular purpose. No warranty is made as to the use or effects incidental to such use, handling or possession of the materials herein described. User is responsible for determining whether this product is fit for a High s Spray Grade Contact Adhesive See Material Safety Data Sheet for Proper Handling and Safety Information REV 08/05 444

12 Glue, Z Solvent Free Post formable adhesive is a high strength contact adhesive specifically designed to bond a wide variety of substrates in woodworking, laminating, and many other applications. Z provides excellent initial and ultimate bond strengths as well as exceptional heat resistance. Z is ideal for post forming operations, and combines zero flammability with zero VOC s, zero Methylene Chloride and zero HAPS. Contributes to LEED and other green building credits GREENGUARD Indoor Air Quality Certified GREENGUARD for Children Schools Compliant with SCAQMD, Rule 1168 NAHB National Green Builders Program Z S Contact Adhesive (5 gallon) Contact Adhesive (50 gallon) s STA -PUT and TACC Spray Bonds Plastic Wood Glass Most Plastics Mirrors Metal STA -PUT High Temperature Spray Adhesive S Clear 15 oz. Spray Can Non-Flamable S Clear SPH (37 lb. canister) Contact Adhesive (55 gallon) Contact Adhesive (55 gallon) Clear (375 lb.) STA -PUT Application Equipment S Stainless Steel Spray Gun with Tip High Spray Gun without Tip Gun Tip for Hose Hose Hose

13 , Glue s DAP Weldwood Original Contact Cement Premium quality, brush grade, neoprene-based contact cement that meets the stringent requirements of the professional user. High strength and initial grab make it ideal for most projects. Fast-drying formula dries in minutes. Offers high heat and water resistance when dry. Exceeds industry performance requirements Conveniently available in quarts, gallons and larger containers 1 Quart Order Number Gallon Order Number DAP Weldwood Nonflammable Contact Cement High solids polychloroprene, waterborne contact adhesive that meets the stringent requirements of the professional user. Complies with all current VOC requirements. Dries in minutes, allowing for extra bonding time. Water resistant when dry. Exceeds industry performance requirements. Low odor. Easy water clean-up. SIZE TYPE DAP COLOR SOLIDS Gallon Spray Grade 2146 Green 25% Flatwork Spray Grade Contact Adhesive Professional use only Flatwork applications (non-postforming) Designed for economy and efficiency for non-postforming high speed applications Easy sprayability Aggressive tack 5 Gallon Order Number Gallon Order Number

14 Glue, DAP Weldwood Carpenter s Wood Glue Professional quality aliphatic resin wood and multi-purpose glue providing a high strength bond. Sets fast, grips tight, sands easily when dry. Heat, water, and solvent resistant. Non-toxic. Low VOC Reduce Environmental Impact by Choosing Low VOC Content Products DAP is dedicated to the development of adhesives and sealants with low volatile organic compound (VOC) content.many of our products actually have a low enough VOC content, indicated by this symbol, to meet one or more of the guidelines outlined below: The South Coast Air Quality Management District (SCAQMD) Rule # 1168 The Bay Area Air Quality Management District Regulation 8, Rule 51 U.S. Green Building Council LEED -NC Green Building Rating System for New Construction Major Renovations Version 2.2, EQ Credit 4.1 (Indoor Environmental Quality Low Emitting Materials: Sealants) NAHB Model GREEN Home Building Guideline Section (Global Impact - Products) Order Number WELDWOOD YELLOW GLUE GAL GAL QUART s DESCRIPTION SIZE Lacquer Thinner 1 Gallon Lacquer Thinner 5 Gallon Contact Cleaner 1 Gallon Contact Cleaner 5 Gallon Mineral Spirits 1 Gallon Mineral Spirits 5 Gallon Wash Thinner To clean spray guns and equipment Gallons 55 Gallon drums available by special order 447

15 , Glue s DAP ALEX PLUS Acrylic Latex Caulk Plus Silicone Superior quality, multi-purpose acrylic latex caulk plus silicone. Highly flexible and durable. Excellent adhesion. Cured caulk is mildew resistant. Interior/exterior use. Paintable. Water clean-up. 35 Year Durability Guarantee. Exceeds ASTM Specification C 834. COLOR WE ALMOND BROWN GRAY CEDER TAN BLACK CLEAR DAP Silicone Sealant Superior quality, multi-purpose sealant. Offers long-lasting flexibilty and excellent adhesion. Provide a weatherproof, watertight seal. Resists cracking, crumbling and chalking. Interior/ exterior use. 50 Year Durability Guarantee. Meets Federal Specification TT-S A, Class A DAP Silicone Sealant COLOR CLEAR DAP KWIK SEAL Tub Tile Adhesive Caulk DAP Kwik Seal Tub Tile Adhesive Caulk Bonds like a glue and seals like a caulk. Provides a durable, watertight seal. Excellent adhesion and flexibility. easily. Cured caulk is mildew resistant. Paintable. Easy water clean-up 5.4 Oz. DAP Kwik Seal Tub Tile COLOR WE ALMOND DAP Beats the Nail VOC-Compliant Construction Adhesive A high-strength, weatherproof adhesive specifically formulated for heavy-duty general construction, remodeling, maintenance and repair projects. VOC compliant. Instant Grab formulation holds projects in place instantly, reducing bracing requirements. It bonds to a wide variety of substrates and provides a heat and water-resistant bond. Meets ASTM Specification C 557. It is low odor and cleans up easily with soap and water. Interior/exterior use. DAP Beats the Nail DESCRIPTION HEAVY DUTY All-Purpose 448

16 Glue, DESCRIPTION Standard Colors Woodgrain SeamFil KITS SeamFil SOLVENTS DESCRIPTION /2 Pint Solvent Quart Solvent Gallon Solvent DRYING RETARDER Order Number COLOR Complete List of Standard SeamFil Colors Available COLOR KAMPEL White Gray Dark Gray Tan Brown Black Mahogany Pink Maple Teak Gray Walnut Birch Primary Yellow Primary Red Olive Orange Almond Clear Mixer (gloss) Spectrum Green Spectrum Blue Butcher Block 942 ColorFlex Standard Line Order Information KAMPEL White CF Putty Grey CF Pumice CF Almond CF Beige CF Desert CF Khaki CF Daffodil CF Terra Cotta CF Hollyberry CF Burgandy CF Wine CF Fawn CF Spice CF Blush CF Plum Brown CF Lavender CF Plum CF Blue Iris CF Royal Blue CF8154 COLOR CAULKING KAMPEL Indigo CF Sea Green CF Brite Green CF Leaf Green CF Deep Green CF Teal CF Butcherblock CF Peanut CF Praline CF Buckskin CF Chamois CF Teak CF Ginger CF Fudge CF Chocolate CF Platinum CF Dolphin CF Metal Grey CF Charcoal CF Sable CF8218 FOR REPAIR OF ALL LAMINATED PLASTICS Fill in seams...seal joints...repair defects...add the perfect finishing touch to laminated plastic surfaces with Kampel SeamFil. You ll be delighted with the results. Match any laminate pattern, color, or woodgreain, by applying SeamFil directly, or, in some cases, by easily mixing several colors using the color guide. Kits, guides and other Seamfil accessories are available from your distributor. COLOR KAMPEL Sand CF Grey Suede CF Hickory CF Coffee CF Black CF Pink? French Blue? Mahagany? Granite? s 449

17 , s Gold Is Designed For Finishing And Heavy Stock Removal. The Durable Aluminum Oxide Grain Delivers A Fast, Exceptionally Long Lasting Cut. Proprietary Backing Is Stronger Than Other Competitive Brands Using Traditional Backing. High Strength Resin Bonding For Superior Grain Support. A Special Stearate Coating Is Used To Maximize Resistance To Clogging And Loading. A Uniform, Semi Open Coat Design Produces An Even, Consistent Scratch Pattern. 5 AUTONET MESH ABRASIVES DISC Item Number Description Grit Grit Grit Technical Specifications Grain Bonding Backing Coating Color Grit range Aluminum Oxide Resin over Resin Progressive Bond P36-P40 E-Weight Paper P D-Weight Latex Paper P C-Weight Latex Paper Semi-Open Gold P36-P500 AUTONET MESH ABRASIVES DISC 5 GOLD PSA Disc No Hole Item Number Description Grit Grit Grit Grit Grit 5 GOLD VELCRO Disc No Hole Item Number Description Grit Grit Grit Grit Grit MIRKA GOLD ABRASIVES DISC 450

18 , s Portable Belts Hiolit X-Weight Cloth Belts Are Designed For Maximum Performance. Belts Are Fully Resin Bonded To Maximize Performance Life In Machine Sanding Operations. The Rigid Cotton Cloth Backing Is Highly Tear Resistant. The Grit Configuration Removes Stock Quickly, While Producing A High Quality Finish. Durable Aluminum Oxide Grain Delivers An Exceptionally Long Lasting Cut. Available In 2.5, 3 And 4 Widths. 3 x 21 Heavy Duty Abrasive Belts 9 x 11 Silicon Carbide Sheet Item Number Description Item Number Description Grit Grit Grit Grit Grit Grit Grit 5 PSA Discs Silicon Carbide Grit Item Number Description 3 x 24 Heavy Duty Abrasive Belts Grit Item Number Description Grit Grit Grit Grit Grit Grit Grit Grit Grit Grit Grit 4 x 24 Heavy Duty Abrasive Belts 5 PSA Cloth Discs Item Number Description Item Number Description Grit Grit Grit Grit Grit Grit Grit Grit Grit Grit 9 x 11 Aluminum Oxide Sheet Grit Item Number Description Grit Grit Grit Grit 9 x 11 Silicon Carbide Waterproof Item Number Description Grit Grit Grit Grit 451

19 , s Discs Rolls No Dust Holes 6 DISCS GRIT/WT PCS/BX BX/CASE Discs for Porter-Cable # 7336 and all 6 Air D-A Machines Platinum Stearated Non-Loading Discs PSA MERCER ABRASIVES A DIVISION OF MERCER TOOL CORP. Benefits: Prevents loading Heat resistant Excellent finish Quick change Highly flexible latex paper backing protects disc Strength of adhesion : Silicon Carbide grain Platinum stearate Individual peall-off backing Heavy C-wt. paper Resin on resin bond Premium Gold Stearated Non-Loading Discs PSA MERCER Sanding Sponge Single Discs with Tabs No Dust Holes 6 DISCS GRIT/WT PCS/BX BX/CASE C C C C C C C Discs for Porter-Cable # 7336 and all 6 Air D-A Machines MERCER ABRASIVES A DIVISION OF MERCER TOOL CORP. Benefits: Extra strength Use wet or dry Extremely flexible for tight corners : Aluminum Oxide fabric reinforcement Color coded for grit 1 side of abrasives 3 x 4 x 1/2 Sanding Sponges SPONGES BOXES GRIT PER BOX PER CASE Fine Fine Medium Medium Medium Coarse

20 , 9 x 11 Garnet Paper Sheets : Natural Garnet abrasive Resin on resin bond High quality latexbacked paper Open coat Benefits: Soft sure cutting Resists moisture and heat Resists loading MERCER ABRASIVES A DIVISION OF MERCER TOOL CORP. GRIT/WT. PCS/BOX BOX/CASE A A A A s 6" Bulldog Gold 5" Finishing Sander Technical Specifications Grain Bonding Backing Coating Color Grit range 6 GOLD VELCRO Disc No Hole Item Number Aluminum Oxide Resin over Resin Progressive Bond P36-P40 E-Weight Paper P D-Weight Latex Paper P C-Weight Latex Paper Semi-Open Gold P36-P500 Description Grit Grit Grit Grit Grit *The Above Items Available Upon Request* Mirka s finishing sanders are constructed of precision molded composites for strength and durability, while reducing operator fatigue. This construction also reduces sound for increased comfort. True 12,000 rpm performance -for maximum productivity. Each model is counter-balanced for its specific size backup pad. moisture-resistant composite rotors, and premium counterweight bearings for long life and superior reliability. S 5 Finishing Sander (5mm, 3/16 orbit)