Installation Instructions

Size: px
Start display at page:

Download "Installation Instructions"

Transcription

1 READ BEFORE INSTALLING UNIT For Through-the-Wall Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit. Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended period of time. Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. Make sure air conditioner does not fall during installation. Do This First (for existing sleeve) Note that the air conditioner dimensions are: 4" wide,4" high, and 9" deep (without front). Install Air Conditioner according to these installation instructions to achieve the best performance. Save these installation instructions for future reference. NOTE: DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE Items in Kit You may not need all parts in the kit. Discard unused parts. No. Hardware Qty. No. Hardware Qty. Tapered Spacer Blocks (7 Long) 0 Trim Frame (side legs) Centering/Support Blocks ( 4 x x ) 4 Trim Frame (top & bottom legs) Plastic Divider ( x 4 x 4 ) 8 Ground Wire (green) 4 Stuffer Seal ( x x 84 ) Toothed washer for grounding screw 5 seal ( x x 5 ) 4 Grounding Screw 6 seal ( x x 4 ) 7 seal ( x /8 x 5 ) 5 Grille (plastic) 6 Grille Aluminum 8 seal ( x /8 x 4 ) 7 Nuts (plastic) 4 9 seal ( x /4 x 4 ) 8 Screw w/washer 4 00A64

2 How to Install. Identify the wall-sleeve brand for your installation, from the chart below. Brand Wall Sleeve Dimensions Width Height Depth White-Westinghouse , 7 or Frigidaire , 7 or Carrier (5F Series) , 7 or General Electric/Hotpoint Whirlpool or Fedders/Emerson or 9 4 Sears/Kenmore Emerson/Fedders Carrier (5S Series) Friedrich IMPORTANT All wall sleeves used to mount the new Air Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve, or rear flange that serves as a stop for the Air Conditioner. CAUTION: When installation is complete, replacement unit MUST have a rearward slope as shown in Fig... Remove old Air Conditioner from wall sleeve and prepare wall sleeve as follows: Clean interior (do not disturb seals). Wall sleeve must be securely fastened in wall before installing Air Conditioner. Drive more nails or screws through sleeve, into wall, if needed. Retouch wall sleeve painted surface if needed.. If not existing, drill a /6" clearance hole for grounding screw through left side of wall sleeve, in a clear area about inches maximum back from front edge of sleeve, using grounding screw and toothed washer. Pull loose end of ground wire out front of sleeve, and temporarily bend it down and around lower edge of sleeve (Fig.). This ground wire will later be attached to frame of air conditioner once it is installed. REAR Wall sleeve /4" to 5/6" UNIT FRONT Wall sleeve to unit sleeve grounding Max. Hole Fig. LEVEL Fig.

3 4. Prepare the wall sleeve for installation of the new unit per the following Brand instructions. # Emerson 5 Deep # Fedders 9 4 Deep # Fedders or Friedrich 6 4 Deep 7 #4 General Electric/Hotpoint 6 8 Deep 5 #5 Sears or Carrier(5S Series) 8 8 Deep #6 Whirlpool 7 8 Deep #7 Whirlpool Deep #8 White-Westinghouse/Frigidaire/ Deep Carrier(5F Series) #9 White-Westinghouse/Frigidaire Deep 5. Identify your wall sleeve type and follow the instructions for that type in the following pages. IMPORTANT This unit's increased performance characteristics result from having two rear air intakes. It is very important that these installation instructions are followed so your unit can operate at maximum efficiency. If there is an existing sleeve, and there is an existing rear grille, it needs to be replaced by one that has been shipped with the unit in the accessory kit. FOR INCREASED EFFICIENCY, UTILIZE THE PROVIDED LOUVERED REAR PANEL Installation of new grille provided with unit. Remove the existing grille.. Place the grille included with the new air conditioner towards the rear of the sleeve.. Mark through the hole positions. 4. Drill through the sleeve flanges with a /8" drill bit. 5. Attach the new grille with self-threading screws and washers(not included). 6. It is VERY IMPORTANT that the grille is placed exactly as shown. 7. Most decorative exterior grilles may be left in place as long as the proper interior air direction grille is installed. NOTE: If the provided grill is not used, it may lead to product damage and possible failure.

4 # Emerson 5" Deep. Remove existing rear grille as shown on Page of this manual and. Attach()" x /8" x 5" long seal in the center at the top of the sleeve. Remove the backing paper and press into position.. Attach()" x /8" x 4" seals to the left and right sides of the sleeve. 4. Cut()" x /8" x 5" long seals to 4" long each and attach to the vertical sections of the grille as shown. 5. Attach () 4 " x " x " centering/support blocks one on each side wall. Place in center of side wall with the tapered end facing the opening. 6. Gently slide unit into sleeve. 7. Before sliding all-the-way back, remove nd screw from fron on left side of unit. 8. Remove the plastic washer from the screw. 9. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet. 0. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled.. Seal & Frame the unit as described on the last page of these instructions.. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page. 4

5 # Fedders 9-/4" Deep. Remove existing rear grille as shown on Page of this manual and. Attach () 4 " x " x " centering/support blocks one on each side wall. Place in center of side wall with the tapered end facing the opening.. Cut () 7" Tapered Spacer Blocks as shown below into two pieces. 7" /4" Tapered Spacer Block " Cut Here 4" protection Paper Backing 4. The 4" section is placed in front of the rib on base with the tapered end facing the back of the sleeve. The remaining portion will be placed behind the rib again sloping toward the rear of the sleeve. This helps induce a rearward slope on the unit. 5. Attach () " x /8" x 5" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 6. Attach () " x /8" x 4" seals to the left and right sides of the sleeve. 7. Cut () " x /8" x 5" long seals to 4" long each and attach to the vertical sections of the grille as shown. 8. Gently slide unit into sleeve. 9. Before sliding all-the-way back, remove nd screw from front on left side of unit. 0. Remove the plastic washer from the screw.. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled.. Seal & Frame the unit as described on the last page of these instructions. 4. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page. 5

6 # Fedders or Friedrich 6-/4" Deep. Remove existing rear grille as shown on Page of this manual and. Attach () 4 " x " x " centering/support blocks one on each side wall. Place in center of side wall with the tapered end facing the opening.. Cut () 7" Tapered Spacer Blocks as shown below into two pieces. 7" /4" Tapered Spacer Block " Cut Here -/" -/" protection Paper Backing 4. The " section is placed in front of the rib on base with the tapered end facing the back of the sleeve. Cut the remaining portion to " and place behind the rib again sloping toward the rear of the sleeve. This helps induce a rearward slope on the unit. 5. Attach () " x /8" x 5" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 6. Attach () " x /8" x 4" seals to the left and right sides of the sleeve. 7. Cut () " x /8" x 5" long seals to 4" long each and attach to the vertical sections of the grille as shown. 8. Gently slide unit into sleeve. 9. Before sliding all-the-way back, remove nd screw from front on left side of unit. 0. Remove the plastic washer from the screw.. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled.. Seal & Frame the unit as described on the last page of these instructions. 4. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page. 6

7 #4 General Electric/Hotpoint 6-7/8" Deep. Remove existing rear grille as shown on Page of this manual and. Cut () 7" Tapered Spacer Blocks as shown below into two pieces. 7" 4.5" 4" /4" Tapered Spacer Block " Cut Here " protection Paper Backing. Install as shown with the tapered end /" from the back of the sleeve. This helps induce a rearward slope on the unit. 4. Attach () " x /8" x 5" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 5. Attach () " x /8" x 4" seals to the left and right sides of the sleeve. 6. Cut () " x /8" x 5" long seals to 4" long each and attach to the vertical sections of the grille as shown. 7. Center unit & gently slide unit into sleeve. 8. Before sliding all-the-way back, remove nd screw from front on left side of unit. 9. Remove the plastic washer from the screw. 0. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled.. Seal & Frame the unit as described on the last page of these instructions.. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page. 7

8 #5 Sears or Carrier 5S Series 8-5/8" Deep. Remove existing rear grille as shown on Page of this manual and. Install () tapered spacer blocks to the floor of the sleeve as shown. This helps induce a rearward slope on the unit.. Install as shown with the tapered end /" from the back of the sleeve. This helps induce a rearward slope on the unit. 4. Attach () " x /8" x 5" long seal in the center at the top of the sleeve. Remove the backing paper and press into position 5. Attach () " x /8" x 4" seals to the left and right sides of the sleeve. 6. Cut () " x /8" x 5" long seals to 4" long each and attach to the vertical sections of the grille as shown. 7. Center unit & gently slide unit into sleeve. 8. Before sliding all-the-way back, remove nd screw from front on left side of unit. 9. Remove the plastic washer from the screw. 0. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled.. Seal & Frame the unit as described on the last page of these instructions.. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page. 8

9 #6 Whirlpool 7-/8" Deep. Remove existing rear grille as shown on Page of this manual and. Cut () 7" Tapered Spacer Blocks as shown below into two pieces. 7" /4" Tapered Spacer Block " Cut Here " protection Paper Backing. Install to the floor of the sleeve as shown. This helps induce a rearward slope on the unit. 4. Attach () " x /8" x 5" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 5. Attach () " x /8" x 4" seals to the left and right sides of the sleeve. 6. Cut () " x /8" x 5" long seals to 4" long each and attach to the vertical sections of the grille as shown. 7. Center unit & gently slide unit into sleeve. 8. Before sliding all-the-way back, remove nd screw from front on left side of unit. 9. Remove the plastic washer from the screw. 0. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet.. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled.. Seal & Frame the unit as described on the last page of these instructions.. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page. 9

10 #7 Whirlpool Deep. Remove existing rear grille as shown on Page of this manual and 4.5" 4" Because of the increased unit depth, first try dry fitting using the method described below:. Place () " x " x 4" seals against each side.. Gently slide unit in and check if amount extending from the sleeve is sufficient once the trim frame is attached. 4. If position is okay, remove unit and Proceed to the next step.if not go to step Attach () " x " x 5" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. 6. Attach () " x " x 4" seals to the left and right sides of the sleeve. 7. Cut () " x /8" x 5" long seal to 4" long each and attach to the vertical sections of the grille as shown. 8. Attach the tapered spacer blocks to the floor of the sleeve. Now go to step 5. Use these next steps if the unit requires extra extension into the room. 9. Attach " x 4 " x 4" long seal over the solid vertical portion of the rear grille. 0. Attach () 4 4 " x 4 " x 4 " foam blocks with the slot overlapping the seal above.. Install the divider into the slots of the foam blocks. You may need to trim the length to size.. Repeat steps 9- for the other vertical shown portion of the grille as shown in the picture.. Attach () " x " x 4" seals along the sides of the sleeve again making sure all seals are flush. 4. Cut the " x " x 5" seal to fit the top of the sleeve. The pieces must be fitted flush to the edge of the divider. 5. Center unit & gently slide unit into sleeve. 6. Before sliding all-the-way back, remove nd screw from front on left side of unit. 7. Remove the plastic washer from the screw. 8. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet. 9. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled. 0. Seal & Frame the unit as described on the last page of these instructions.. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page. 0

11 #8 White Westinghouse/Frigidaire/ Carrier 5F Series 6"+ 7-/" Deep. Remove existing rear grille as shown on Page of this manual and. Attach () " x /8" x 5" long seal in the center at the top of the sleeve. Remove the backing paper and press into position.. Attach () " x /8" x 4" seals to the left and right sides of the sleeve. 4. Attach () " x 4 " x 4" long seal vertically.5" from the left side of the sleeve. Attach the other " x 4 " x 4" long seal " from the right side of the sleeve. 5. Center unit & gently slide unit into sleeve. 6. Before sliding all-the-way back, remove nd screw from front on left side of unit. 7. Remove the plastic washer from the screw. 8. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet. 9. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled. 0. Seal & Frame the unit as described on the last page of these instructions.. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page. 4.5" 4"

12 #9 White Westinghouse or Frigidaire Deep. Remove existing rear grille as shown on Page of this manual and Because of the increased unit depth, first try dry fitting using the method described below:. Place () " x " x 4" seals against each side.. Gently slide unit in and check if amount extending from the sleeve is sufficient once the trim frame is attached. 4. If position is okay, remove unit and Proceed to the next step.if not go to step Attach () " x " x 5" seal to the left and right sides of the sleeve. 6. Cut () " x " x 5" long seal to 4" long and attach it vertically to the rear grill.5" from the left side. Repeat and attach " from the right side. 7. Attach () " x " x 5" long seal in the center at the top of the sleeve. Remove the backing paper and press into position. Proceed to step 4. Use these next steps if the unit requires extra extension into the room. 8. Attach " x 4 " x 4" long seal over the solid vertical portion of the rear grille. 9. Attach () 4 4 " x 4 " x 4 " foam blocks with the slot overlapping the seal above. 0. Install the divider into the slots of the foam blocks. You may need to trim the length to size.. Repeat steps 8-0 for the other vertical shown portion of the grille as shown in the picture.. Attach () " x " x 4" seals along the sides of the sleeve again making sure all seals are flush.. Cut the " x " x 5" seal to fit the top of the sleeve. The pieces must be fitted flush to the edge of the divider. 4. Center unit & gently slide unit into sleeve. 5. Before sliding all-the-way back, remove nd screw from front on left side of unit. 6. Remove the plastic washer from the screw. 7. Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture. Make sure that the toothed washer is against the cabinet. 8. Slide the unit completely to the rear to ensure a good seal, making sure the ground wire does not become tangled. 9. Seal & Frame the unit as described on the last page of these instructions. 0. If you have difficulty with mounting the grill to the sleeve, follow the instructions for direct mounting on Page.

13 Direct Unit Mounting Installation Instructions The previous directions are the preferable way to mount the new rear grill. The unit s performance is slightly better and the possibility of draughts is reduced. As a last resort, direct mounting of the grille to the unit can be considered. Note: The grille must be installed prior to inserting the unit into the sleeve. Position the grille over the rear of the unit making sure that: a. The double set of screw holes are at the bottom. b. The fins of the grill are pointed away from the unit. seal seal Grille Screws Location Hole Grille & lange Screw

14 FINISHING INSTALLATION: Installation Instructions. Install the " x " x 84" long stuffer seal between the wall-sleeve and the unit. A flat-bladed screwdriver or putty knife is recommended.. Assemble the trim frame by inserting top and bottom pieces into side pieces and snapping into place.. Pull cord through trim frame then slide over unit until flush with wall. NOTE: For larger sleeves, an accessory trim kit is available(ea0t). Call MY-HOME to order and purchase kit. 4

READ BEFORE INSTALLING UNIT

READ BEFORE INSTALLING UNIT READ BEFORE INSTALLING UNIT For Through-the-Wall Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:

More information

READ BEFORE INSTALLING UNIT

READ BEFORE INSTALLING UNIT READ BEFORE INSTALLING UNIT For Through-the-Wall Air Conditioners To avoid risk of personal injury, property edges that may be exposed: damage, or product damage due to the weight of this device and sharp

More information

Installation Instructions:

Installation Instructions: Installation Instructions: Do This First (for existing sleeve) Note that the air conditioner dimensions are: "wide, 1 1 "high, and 18 1 "deep (without front). Install Air Conditioner according to these

More information

Installation Instructions: 8,000-12,000 BTU TTW

Installation Instructions: 8,000-12,000 BTU TTW Installation Instructions: 8,000-1,000 BTU TTW Do This First (for existing sleeve) Note that the air conditioner dimensions are: "wide, 1 1 "high, and 18 1 "deep (without front). Install Air Conditioner

More information

Do This First (for existing sleeve)

Do This First (for existing sleeve) Installation Do This First (for existing sleeve) Note that the air conditioner dimensions are: 4"wide, 4½" high, and 8½" deep (without front). Install Air Conditioner according to these installation instructions

More information

Installation Instructions

Installation Instructions READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes

More information

Installation Instructions

Installation Instructions For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp

More information

READ BEFORE INSTALLING UNIT Compact Window Mounting (10-12K BTU)

READ BEFORE INSTALLING UNIT Compact Window Mounting (10-12K BTU) READ BEFORE INSTALLING UNIT Compact Window Mounting (10-12K BTU) To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:

More information

Installation Instructions

Installation Instructions For Medium (15-18.5K) + Heavy duty (-8.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges

More information

Installation Instructions

Installation Instructions 3 4 5 3 4 5 6 7 8 9 0 Installation Instructions READ BEFORE INSTALLING UNIT Compact Window Mounting (0~K BTU) To avoid risk of personal injury, property damage, or product damage due to the weight of this

More information

Installation Instructions

Installation Instructions 3 4 5 3 4 5 6 7 8 9 0 Installation Instructions READ BEFORE INSTALLING UNIT MSII MSIII Window Mounting (5,000~8,000 BTU) INSTALLATION WARNINGS AND CAUTION The unit is for window mounting only. Carefully

More information

Installation Instructions

Installation Instructions READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:

More information

Installation Instructions

Installation Instructions edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung

More information

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully

More information

Installation Instructions For Heavy Duty (FAS Models) and Median (FAM Models) Air Conditioners

Installation Instructions For Heavy Duty (FAS Models) and Median (FAM Models) Air Conditioners Installation Instructions For Heavy Duty (FAS Models) and Median (FAM Models) Air Conditioners Please read ALL instructions before installing. Two people are recommended to install this product. If a new

More information

Installation Instructions

Installation Instructions Installation Instructions READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as

More information

READ BEFORE installing UNiT

READ BEFORE installing UNiT READ BEFORE installing UNiT For Slider Casement Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:

More information

INSTALLING YOUR NEW SPRING LIFT ARM KIT

INSTALLING YOUR NEW SPRING LIFT ARM KIT INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as

More information

Installation Instructions For Slider Casement Air Conditioners

Installation Instructions For Slider Casement Air Conditioners Installation Instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT

More information

Installation Instructions

Installation Instructions 3 4 5 3 4 5 6 7 8 9 0 Installation Instructions READ BEFORE INSTAING UNIT BR Window Mounting (0,000 -,000 BTU) INSTAATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. be

More information

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS

RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.

More information

INSTALLATION INSTRUCTIONS RH 412 STEEL DOORS

INSTALLATION INSTRUCTIONS RH 412 STEEL DOORS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job

More information

Bulkhead Model Number and

Bulkhead Model Number and Bulkhead Model Number 96141-3-01 and 96142-3-01 Installing your ProMaster bulkhead is very clear cut following these instructions. Before cutting or drilling in the floor, verify the location of you gas

More information

READ BEFORE installing UNiT

READ BEFORE installing UNiT READ BEFORE installing UNiT For Slider Casement Air Conditioners Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes

More information

Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing)

Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Series 7600 Installation Instructions Aluminum Multi-Slide Door (Pocketing) Things to Know Before You Start Things to Know Before You Start Removal of Old Fenestration Products Ensure any old fenestration

More information

Installation Manual MODEL NE-42

Installation Manual MODEL NE-42 Installation Manual MODEL NE-42 GET TO KNOW YOUR UNIT 1 1. CROSS BRACES - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with 1/4 & 1/8 drill bit)

More information

Model No. EP84-A, EP84AR-A, P84L

Model No. EP84-A, EP84AR-A, P84L E000 Model No. EP84-A, EP84AR-A, P84L PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR BUILDING CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces

More information

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS

TRUE TECHNICAL SERVICE MANUAL - ALL MODELS.  DOORS/DRAWERS/LIDS DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary

More information

4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside.

4. Partially open the operating panel and tilt the top toward the interior of the door (Figure 4). Lift the panel off the sill and set it aside. Effective Date: 10/1/2017 Tools Needed Kit Contents Hardware Kit Safety Glasses Cordless drill Phillips screw bit Two-step drill bit (3/8-1/8 ) utility knife Interior Mullion Exterior Mullion Cover clamps

More information

Block Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5.

Block Frame Inovo Patio Door/Transom/Sidelite Field Mulling Instructions. simonton.com/installation. If mulling sidelites, skip to Step 5. Effective Date: 10/1/17 Tools Needed Kit Contents Safety Glasses Cordless Drill Phillips Screw Bit Two-step Drill Bit (3/8-1/8 ) Utility Knife Interior Mullion Exterior Mullion Cover Hardware Kit Clamps

More information

Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows

Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows Installation Instructions Double-Hung, Single-Hung, Casement, Awning, Sliding, Picture & Shapes Non-Impact & Impact Resistant Nailing Fin Windows americancraftsmanwindows.com Project Requirements: Read

More information

Installation Instructions

Installation Instructions Installation Instructions This kit provides for the installation of a stainless steel unified grille panel. The panel will span the combined width of a side-by-side installation. THE INSTALLATION SPACE

More information

English/French 06/04

English/French 06/04 E000 PLEASE READ ASSEMBLY INSTRUCTIONS COMPLETELY BEFORE ASSEMBLING YOUR BUILDING CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 39680 (Black) & 39681 (Chrome) For Ford 4x4 F150, F250 Light Duty & Expedition As you read these instructions, you will see NOTES, CAUTIONS

More information

GE Monogram. Installation. Instructions. 36" Vent Hood. Model ZV750. Call anywhere in the US and Canada -

GE Monogram. Installation. Instructions. 36 Vent Hood. Model ZV750. Call anywhere in the US and Canada - at :: rangehoods. com GE Monogram Instructions Model ZV750 GE Monogram at:: rangehoods. com is a division of CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:

More information

MISCELLANEOUS CABINET REPAIRS

MISCELLANEOUS CABINET REPAIRS MISCELLANEOUS CABINET REPAIRS 167 168 NOTES MISCELLANEOUS CABINET REPAIRS Cabinet Panel Repairs 175 SIDE PANEL REPLACEMENT - GDM SERIES INSTALLATION INSTRUCTIONS Tools Required 1/8" drill Rivet Tool Silicone

More information

Driver/Left Top. Support Bracket

Driver/Left Top. Support Bracket PARTS LIST: 1 Grille Guard 8 10mm Lock Washers 1 Driver/Left Frame Bracket 8 10mm Hex Nuts 1 Passenger/Right Frame Bracket 2 8-1.25mm x 25mm Button Head Bolts 1 Driver/Left Bottom Support Bracket 2 8mm

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

installation instructions For Slider Casement Air Conditioners

installation instructions For Slider Casement Air Conditioners installation instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT

More information

Series----SP3600A SHOWER DOOR

Series----SP3600A SHOWER DOOR Series----SP3600A SHOWER DOOR INSTALLATION INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram

More information

PRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit

PRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit R INSTALLATION INSTRUCTIONS PRODUCT: LOKI CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED TOOLS

More information

Frameless Fixed Panel Slider

Frameless Fixed Panel Slider INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need

More information

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER. SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information

Customer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR

Customer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from

More information

Installation And Care Instructions. Vertical Honeycomb Shades

Installation And Care Instructions. Vertical Honeycomb Shades Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

INSTRUCTION SHEET U19

INSTRUCTION SHEET U19 U19 All Refrigerator and All Freezer Trim Kit Installation Product Line: U19 All Refrigerator and All Freezer Models Parts Included in Kit TRIMKITEZ1 (Part# 297333500): Single Trim Kit Components Single

More information

WHISPER Cellular EasyRise Shades. Installation Operation Care

WHISPER Cellular EasyRise Shades. Installation Operation Care WHISPER Cellular EasyRise Shades Installation Operation Care 05/2013 CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mounting Types

More information

FIXED PANEL SLIDER QCI5241

FIXED PANEL SLIDER QCI5241 INSTALLATION INSTRUCTIONS FIXED PANEL SLIDER QCI5241 FRAMELESS PANEL / DOOR / PANEL FRAMELESS DOOR / PANEL QCI5241 REV. 0 Page 1 Certified 06/16/2016 Parts List *Quantities may vary QCI5241 REV. 0 Page

More information

Preference Collection and Treatment Console INSTALLATION GUIDE

Preference Collection and Treatment Console INSTALLATION GUIDE Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 645 For Chevrolet Silverado 500HD & 3500 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of looks,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Furniture Solutions: 68 Shipstation with Storage Shelf Model Numbers: PB001 (D9001, D9010N, D9021, D9030, D9032/D9033, D9098, RC4054) Introduction This document provides the Pitney

More information

S H E D A S S E M B L Y I N S T R U C T I O N S

S H E D A S S E M B L Y I N S T R U C T I O N S T I T A N R A N G E S H E D A S S E M B L Y I N S T R U C T I O N S 6 X 4ft = 190 x 150 cm 6 X 6ft = 190 x 190 cm 6 X 8ft = 190 x 255 cm COMPONENT LIST Component illustrations are given as a visual guide

More information

INSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AE Last Updated: 09/08/14 US PATENTS: D683281, D CHINESE PATENT: ZL

INSTALLATION GUIDE PREMIUM FRONT BUMPER. AEV30103AE Last Updated: 09/08/14 US PATENTS: D683281, D CHINESE PATENT: ZL PREMIUM FRONT BUMPER US PATENTS: D683281, D697842 CHINESE PATENT: ZL 2012 3 0026081.4 AEV30103AE Last Updated: 09/08/14 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION,

More information

Frameless Inline Door With Return QCI5263

Frameless Inline Door With Return QCI5263 INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges

More information

Assembly Instructions

Assembly Instructions page 1 Serious personal-injury to the operator or bystanders, as well as damage to equipment or property, can occur, if all safety and assembly instructions, provided with this product, are not followed.

More information

MICRO-AIR DOWNDRAFT TABLES INSTALLATION AND OPERATION MANUAL

MICRO-AIR DOWNDRAFT TABLES INSTALLATION AND OPERATION MANUAL MICRO-AIR DOWNDRAFT TABLES AND OPERATION MANUAL DDT480 & DDT70 Includes Installation, Operation, and Service Instructions IMPORTANT This manual contains specific cautionary statements relative to worker

More information

INSTALLATION INSTRUCTIONS. IMPORTANT- Observe all CAUTION BEFORE YOU BEGIN

INSTALLATION INSTRUCTIONS. IMPORTANT- Observe all CAUTION BEFORE YOU BEGIN BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT- Save these instructions for local inspector s use. IMPORTANT- Observe all governing codes and ordianaces. Note to Installer-

More information

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens

Installation and Assembly - Universal Articulating Swivel Double-Arm for 42 - 60 Plasma Screens Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be

More information

CUSTOM SHUTTERS IN-A-BOX

CUSTOM SHUTTERS IN-A-BOX CUSTOM SHUTTERS IN-A-BOX SHUTTER ASSEMBLE INSTRUCTIONS & INSTALLATION INSTRUCTIONS 1. Inspect the contents of your package. Do not discard the shutter packaging box until you have started painting your

More information

Installation Instructions

Installation Instructions Installation Instructions This kit provides for the installation of a unified grille panel for a framed or overlay custom panel. The panel will span the combined width of a side by side installation. ZUG2

More information

WINE DISPENSING SYSTEM MODEL: DYWS4

WINE DISPENSING SYSTEM MODEL: DYWS4 WINE DISPENSING SYSTEM MODEL: DYWS4 Trim Kit Part Number AWSTK24 INSTALLATION INSTRUCTIONS IMPORTANT: The wine dispensing utilizes a thermo-electric cooling system that can normally cool the bottle bay

More information

Installation Manual MODEL ANE-42

Installation Manual MODEL ANE-42 Installation Manual MODEL ANE-42 GET TO KNOW YOUR UNIT 1 2 1. CROSS BRACES 2. SIDE BRACKETS - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with

More information

GE Monogram. Installation. Instructions. Microwave Oven. Under Cabinet Installation. and. JX827 Series Built-In Kit. Models.

GE Monogram. Installation. Instructions. Microwave Oven. Under Cabinet Installation. and. JX827 Series Built-In Kit. Models. GE Monogram Installation Instructions Under Cabinet Installation and JX827 Series Built-In Kit Models ZEM200 Series CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:

More information

western window systems westernwindowsystems.com installation instructions non-pocket 2-1/4 panels

western window systems westernwindowsystems.com installation instructions non-pocket 2-1/4 panels series 2600 multi-slide non-pocket 2-1/4 panels windowsystems.com windowsystems.com movement, which can cause warping and other problems. Frame kit components: Each door will have a head assembly, a threshold

More information

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER. SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information

Giraud Tool Company, Inc.

Giraud Tool Company, Inc. Motor Upgrade for Gracey Trimmer This package is intended to allow the user to upgrade their Gracey trimmer with a higher rpm motor and convenience features not found in the production offering. This upgrade

More information

PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT

PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT AEV30272AC Last Updated: 10/09/18 PROVEN WORLDWIDE SNORKEL FOR CHEVY COLORADO NEW PRODUCT Please visit www.aev-conversions.com to view the most current installation guide for this product. This is a new

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Thank You, for your recent purchase with TrimLine Windows, Inc. This is a quality product and deserves a quality installation. Please follow the attached instructions for a quick

More information

INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS

INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS 2008 Pella Corporation Part Number: 803V0101 INSTALLATION INSTRUCTIONS IMPERVIA SLIDING PATIO DOOR WITH FINS Installation Instructions for Typical Wood Frame Construction. These instructions were developed

More information

Privacy Wall Glass Selections - Polished Edge Slider Door

Privacy Wall Glass Selections - Polished Edge Slider Door Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin

More information

IMPORTANT! READ BEFORE PROCEEDING! SV Weather Caps

IMPORTANT! READ BEFORE PROCEEDING! SV Weather Caps SV Weather Caps OPERATION & MAINTENANCE Revised: 08/24/15 IMPORTANT! READ BEFORE PROCEEDING! The information contained herein is, to the best of our knowledge, accurate and applicable for proper operation

More information

INSTALLATION AND CARE INSTRUCTIONS

INSTALLATION AND CARE INSTRUCTIONS INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5

More information

HR175 Sash Replacement Kit Installation Instructions

HR175 Sash Replacement Kit Installation Instructions HR175 Sash Replacement Kit Installation Instructions IMPORTANT: Please read before you begin. Weather Shield HR175 Sash Replacement Kits Important: Thoroughly read and follow these instructions, failure

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount For Chevrolet Silverado 1500HD & 2500 Kit 68162 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of

More information

FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283

FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 QCI5283 Page 1 Date Certified: 06/16/2016 Parts List with wall mount clamp ITEM NO. DESCRIPTION QTY. 1 FIXED GLASS PANEL 1 2 WALL MOUNT CLAMP 1 3 U-CHANNEL

More information

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.

More information

INSTALLATION AND CARE INSTRUCTIONS

INSTALLATION AND CARE INSTRUCTIONS INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5 Tools Required...6

More information

Hip Roof Canopy Instructions

Hip Roof Canopy Instructions Hip Roof Canopy Instructions - PUT SAFETY FIRST. NOT COMPLYING WITH THE PROCEDURES AND PRECAUTIONS OUTLINED IN THIS MANUAL MAY RESULT IN PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.. Before attempting

More information

RTI TECHNOLOGIES, INC.

RTI TECHNOLOGIES, INC. RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS BUILDERS CHOICE FRAMED Shower Height Swing Door Model: L533 Rev. 09.03.13 MAINTENANCE: Two primary materials are used to manufacture your new Aquatic enclosure; tempered glass

More information

INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO

INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO 2008 Pella Corporation Part Number: 801P0101 INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR CLAD CASEMENT & AWNING WINDOW VENTANA DE DOS HOJAS CON REVESTIMIENTO Corner Corner Top Fin Corner

More information

model tsa-sa48 Sliding Crosscut Table installation guide

model tsa-sa48 Sliding Crosscut Table installation guide model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop

More information

Baby Grande with Crank, Housing, and Side Rails Installation Instructions

Baby Grande with Crank, Housing, and Side Rails Installation Instructions Baby Grande with Crank, Housing, and Side Rails Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil

More information

1040 & 1050 SERIES HEAVY FRAMELESS BYPASS BATH ENCLOSURE

1040 & 1050 SERIES HEAVY FRAMELESS BYPASS BATH ENCLOSURE INSTALLATION INSTRUCTIONS 1040 & 1050 SERIES HEAVY FRAMELESS BYPASS BATH ENCLOSURE www.alumaxshowerdoor.com Copyright Alumax Bath Enclosures 2014. All rights reserved. !WARNINGS! INSTALLATION WARNINGS

More information

HEAVY DUTY 11 STEEL CABINET

HEAVY DUTY 11 STEEL CABINET HEAVY DUTY STEEL CABINET ASSEMBLY INSTRUCTIONS ONE DRAWER BASE CABINET 05-206 Parts List Part No Description Qty Image ONE DRAWER BASE CABINET Part No Description Qty Image SB- Cabinet Body EH-0 Euro Hinge

More information

INSTALLATION AND CARE INSTRUCTIONS

INSTALLATION AND CARE INSTRUCTIONS INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from

More information

S H E D A S S E M B L Y I N S T R U C T I O N S

S H E D A S S E M B L Y I N S T R U C T I O N S T I T A N R A N G E S H E D A S S E M B L Y I N S T R U C T I O N S 8 X 10 ft Approx = 2550 x 3140 cm COMPONENT LIST Component illustrations are given as a visual guide only and are not in proportion PART

More information

Pet Door Panel Installation Manual

Pet Door Panel Installation Manual Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32

More information

Vinyl Windows and Doors

Vinyl Windows and Doors Vinyl Windows and Doors Part Number: V983571 2011 Pella Corporation INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACION 350 SERIES WINDOW INTO EXISTING WOOD FRAME WINDOW Lea las instrucciones en español

More information

Bolt-On/Rugged Fender Flares Toyota Tundra (14-ON) Important: Please read instructions entirely before installing this product.

Bolt-On/Rugged Fender Flares Toyota Tundra (14-ON) Important: Please read instructions entirely before installing this product. Important: Please read instructions entirely before installing this product. Hardware Included QTY Hardware Included QTY Bolt Kit Included QTY Extrusion 28.0 ft Short Screw 18 Nuts 42 Alcohol Wipe 4 Long

More information

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS

STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS STACKING MULTI-SLIDE DOOR SYSTEM INSTALLATION INSTRUCTIONS 1290363 Revision 1 12/16 Page 1 Weather Shield Mfg., Inc. NOTICE CAUTION! Failure to install and maintain our product according to these instructions

More information

For Barrel Tapers. Installation and Operating Instructions for use with table saws and large disk sanders

For Barrel Tapers. Installation and Operating Instructions for use with table saws and large disk sanders Tim s Taper Tool For Barrel Tapers Installation and Operating Instructions for use with table saws and large disk sanders Your taper tool is capable of making barrel tapered shafts. The term barrel is

More information

Chapter 18. Interior Doors

Chapter 18. Interior Doors Chapter 18. Interior Doors 18.1 SWINGING DOORS 18.2 SLIDING DOORS 18.3 BIFOLD DOORS Tools needed by volunteers: Hammer Nail apron Tape measure Square Pencil Tools and equipment needed: Extension cords

More information

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.

SAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER. SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions

More information

Model 750 Illustrated Installation Instructions Contractors Wardrobe

Model 750 Illustrated Installation Instructions Contractors Wardrobe Model 750 Illustrated Installation Instructions Contractors Wardrobe DESIGNERS MANUFACTURERS 26121 Avenue Hall Valencia, CA 9155 (661) 257-77 Fax: (661) 257-4907 Toll Free: (800) CW-DOORS (800) 29-6677

More information

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A 1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com

More information

A500 ASSEMBLY & INSTALLATION INSTRUCTIONS

A500 ASSEMBLY & INSTALLATION INSTRUCTIONS ASSEMBLY & INSTALLATION INSTRUCTIONS 1 CONTENTS 2 Component Parts A B Canopy Mounting Plate C Cap (3) D Threaded Nipple E Threaded Standoffs (2) F Anchors (8) G #10 Screws (8) H Safety Cable (2) I Safety

More information

Intercooler Shroud and Belt Cover for WRX

Intercooler Shroud and Belt Cover for WRX Intercooler Shroud and Belt Cover for 2015+ WRX 2016-05-18 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation

More information