Handi-Mate TM Shed SLIDING - TYPE HM1

Transcription

1 INSTALLATION GUIDE Handi-Mate TM Shed SLIDING - TYPE HM SHMSSSDHM##

2 BEFORE YOU START Prior to installation, it is important that you contact your local government authority to determine if building approval is required. To ensure that the installation and erection of your Stratco Handi-Mate TM Shed proceeds smoothly you should confirm that all the components and materials listed on the delivery documentation, and in this installation guide, have been supplied. Carefully read this installation guide to familiarise yourself with all the steps involved, and ensure that you have the correct tools and equipment for the job. NOTE: Use heavy gloves when handling steel sheeting and flashings and never attempt to install a shed in windy conditions. TOOLS REQUIRED COMPONENTS x CORNER WALL SHEET SSPHMWSCNR900## WALL SHEET SSPHMWS900## ROOF SHEET SSPHMRS95AZ x4 x x

3 3 SPLIT WALL SHEET SSPHMSW900## SPLIT DOOR SHEET SSPHMSD900## TOP DOOR CHANNEL HMDCTO090GA BOTTOM DOOR CHANNEL HMDCBO090GA VERTICAL DOOR CHANNEL HMDCVE900GA DOOR JAMB HMDJ900GA x x x x x x

4 4 LEFT HAND BARGE CAP HMBCL935## RIGHT HAND BARGE CAP HMBCR935## x x RIDGE CAP HMRC435GA RIDGE BEAM HMRB750GA DOOR SHROUD HMDSBO975GA BARGE SUPPORT HMBS697GA SLIDING RAIL HMSR750GA BOTTOM CHANNEL HMBR750GA RUNNER RAIL HMRRBO697GA SHORT WALL CHANNEL HMWC700GA LONG WALL CHANNEL HMWC750GA x x x x x x x x4 x CORNER BRACKET HMCBGA HMDM## HANDLE MOUNT DOOR LATCH DOOR STOP HMDLGA HMSS DOOR HANDLE DOOR TONGUE DOOR NUT DOOR WHEEL x8 x x x x HMTH HMDT HMDW HMNN6 RIVET RIV4-3## WTK06 0x6 WAFER WTK0 0x WAFER TEK06## COLOUR 0x6 SCREW TEK06 0X6 WASHER SCREW TEKNNW06 0x6 SCREW TEK06## only on colour sheds

5 5 SITE AND ASSEMBLY PREPARATION Preventing Wind Uplift All Stratco Handi-Mate TM Sheds must be securely bolted to a permanent concrete base with sufficient masonry anchors to prevent wind uplift. It is particularly important that masonry anchors are placed within all four corner brackets of the Handi-Mate TM Shed. Further anchors and mounting brackets are also used to fix the Handi-Mate TM Shed to the permanent concrete base according to shed size. The mounting brackets are to be evenly spaced along the length of the wall. Stratco Handi-Mate TM mounting bracket kits can be purchased at Stratco Home Improvement Stores. Concrete Floor Option - Before building the shed, pour a base that is larger than the area by at least 00mm in each direction. The base should be poured so the concrete that will be outside the shed floor area slopes away from the shed to help prevent water from entering the shed. Option - Substantial concrete squares may be used at each anchor location as an alternative to a complete concrete floor Important Notes It is essential to clear and level the site prior to assembling your Stratco Handi-Mate TM Shed. Before starting to build the shed, please refer to the previous pages of this guide for a list of recommended shed assembly tools and shed components. Also note there are different types and colour screws. Ensure that the right type and colour screw is being used at each location. Do not traverse the roof of the Handi-Mate TM Sheds.

6 6 DOOR ASSEMBLY DOOR WHEEL DOOR WHEEL DOOR NUT TOP DOOR CHANNEL DOOR NUT VERTICAL DOOR CHANNEL HANDLE MOUNT 0x6 WAFER SCREW HANDLE MOUNT SPLIT DOOR SHEET WALL SHEET 3 BOTTOM DOOR CHANNEL

7 7 MAKE SURE PRE-PUNCHED HOLES LINE UP IN ALL 4 CORNERS VERTICAL DOOR CHANNEL 4 0x6 WAFER SCREW 0x6 WAFER SCREW 30mm 55mm 45mm 0x6 WAFER SCREW 5 0x6 WAFER SCREW. FIX OUTSIDE CORNERS.. CHECK SQUARE. 3. FIX INSIDE CORNERS & HANDLE MOUNT. 4. FLIP & FIX ON FRONT SIDE. DRILL Ømm HOLE RIVET 6

8 8 FRONT WALL ASSEMBLY 0x6 SCREW x SLIDING RAIL DOOR JAMB CORNER WALL SHEET POSITION THE WALL SHEETS SO THE SCREWS ARE DRIVEN INTO THE CENTRE OF THE PEAK. BOTTOM CHANNEL

9 9 0x6 SCREW 50mm DOOR JAMB DOOR JAMB POSITION THE WALL SHEET SO THE SCREWS ARE DRIVEN INTO THE CENTRE OF THE PEAK.

10 0 BACK WALL ASSEMBLY WALL SHEET CORNER WALL SHEET SPLIT WALL SHEET LONG WALL CHANNEL LONG WALL CHANNEL

11 0x6 SCREW x4 POSITION THE WALL SHEETS SO THE SCREWS ARE DRIVEN INTO THE CENTRE OF THE PEAK. 3 RIVET RIVET 0x6 SCREW 0x6 SCREW 4 POSITION THE WALL SHEETS SO THE SCREWS ARE DRIVEN INTO THE CENTRE OF THE PEAK FOR ALL SCREWS.

12 SIDE WALL ASSEMBLY SHORT WALL CHANNEL CORNER WALL SHEET SHORT WALL CHANNEL

13 x6 SCREW POSITION THE WALL SHEET SO THE SCREWS ARE DRIVEN INTO THE CENTRE OF THE PEAK.

14 4

15 5 SHED ASSEMBLY MAKE SURE PRE-PUNCHED HOLES IN CORNER BRACKET AND WALL PANELS ARE ALIGNED. CORNER BRACKET REPEAT PROCESS FOR THIRD WALL 0x6 SCREW

16 6 3

17 7 4 4 DOOR SHROUD 0x6 SCREW 3 USE DOOR SHROUD AS SPACER TEMPLATE BETWEEN BOTH DOOR JAMBS. DO NOT FIX. RIVET 4 0x6 SCREW 3 4

18 8 600mm 0x6 SCREW 600mm 0x6 SCREW 0x6 SCREW 0x6 SCREW BARGE SUPPORT RUNNER RAIL SLIDING RAIL BOTTOM CHANNEL 5

19 9 CHECK DIAGONALS FOR SQUARE FIX TO CONCRETE WITH ANCHOR ONCE SQUARE 6 0x6 SCREW RIDGE BEAM 835mm 7

20 0 ALIGNED TURN UP VALLEYS ON SHEET TO ENCOURAGE WATER TO FLOW TOWARDS WALLS 8

21 FIXING LOCATIONS FOR ALL ROOF SHEETS.3.. ALL FIXINGS 0x6 WASHER SCREWS.3.. 9

22 RIDGE CAP RIDGE CAP RIDGE BEAM 05mm IN FROM BACK EDGE OF RIDGE CAP THEN CONTINUE WITH 300mm SPACING. 0x6 WASHER SCREW RIDGE CAP 5mm 0

23 3 REMOVE ANY SWARF FROM SLIDING RAIL BEFORE SLIDING DOOR ONTO SHED 630mm DOOR STOP & 0x WAFER

24 4 0x WAFER TIGHTEN SCREW

25 5 DOOR SHROUD 0x6 SCREW 0x6 SCREW X 3

26 6 COLOUR 0x6 SCREW MAX 0mm COLOUR 0x6 SCREW LEFT BARGE CAP 4

27 7 0mm MIN LEFT BARGE CAP RIGHT BARGE CAP RIGHT BARGE CAP 5

28 SECURE THE SHED CONTACT The installer is responsible for ensuring the slab or concrete squares are sufficient to support the shed and sustain wind loading. Do not directly anchor your shed to pavers. 700mm MAX 700mm MAX FIX TO CONCRETE WITH MASONRY ANCHORS 700mm MAX 700mm MAX 700mm MAX 700mm MAX 700mm MAX 700mm MAX 700mm MAX HANDY HINT SHEETS OFF GROUND DURING WALL ASSEMBLY MAINTENANCE Your Stratco Handi-Mate TM Shed will maintain its good looks for even longer with a simple wash and wipe down. Cleaning should be performed as often as is required to remove any dirt, salt and pollutants. Copyright August 05 03/08/5 All brands and logos/images accompanied by or are trade marks of Stratco (Australia) Pty Limited. Stratco Handi-Mate TM Sheds are produced from the highest quality materials and will provide many years of service. Refer to the Selection Use and Maintenance brochure for more information on how to get the best out of your product. BROCSSDHM