miramondo Technical Informations 1/6 Passepartout Concrete

Transcription

1 1/6 Passepartout Concrete Technical Informations

2 Passepartout Concrete 2/6 Dimensions Hole pattern for mounting 590/ / D 12

3 Passepartout Concrete 3/6 Mounting Without foundation with threaded rod With foundation with threaded rod Threaded rod with mounting adhesive Concrete, Asphalt... Do not set nut and bolt in concrete in order to allow later disassembly Threaded rod with mounting adhesive Concrete >300 Gravel, sand... >200 Without foundation with screw and dowel With foundation with ground anchor Screw with dowel Concrete, Asphalt... Do not set nut and bolt in concrete in order to allow later disassembly Ground anchor Concrete 400 Gravel, sand... The fasteners are not included in the scope of delivery! >200

4 Passepartout Concrete 4/6 Maintenance Maintenance and care of the metal parts Notes about cleaning the powder-coated surface: - Only use clear water, if necessary with a little neutral cleaning agent added (ph 7) and soft, non-abrasive rags, cloths or industrial cotton. Do not rub hard. - Remove greasy, oily or sooty substances with aromatic-free petroleum spirits or isopropyl alcohol (IPA). Residues of stickers, chewing gum or adhesive bands, etc. can also be removed this way. - Do not use any solvents that contain esters, ketone, alcohols, aromatics, glycol ether or halogenated hydrocarbons or similar substances. - Do not use anything abrasive that will scratch. - Do not use strong acids or alkali cleaning agents. - Do not use cleaning agents of indeterminate composition. - The cleaning agents may not be used at temperatures that exceed 25 C. Do not use steam cleaning devices. - The surface temperature during cleaning may also not exceed 25 C. - Immediately after each cleaning, rinse with clear, cold water. Notes about refurbishing scratched steel parts: These recommendations will help refurbish a damaged surface. We ask you, however, to consider that refurbishment to the original surface quality is unfortunately not possible. A tolerance of the painted surfaces to cleaning agents, etc. which may be used to clean the surfaces must also be checked in each individual case and considered. The quality of the repairs made depends largely on the skill of the person making them. Unfortunately it is not possible to guarantee a particular result. The metal parts are made of hot-galvanised steel. They have a high-quality coating with a slight metallic pattern. Their colour is anthracite, similar to DB 703 metallic or RAL A single-component nitrocellulose paint with matte surface in the colour tone NCS 7500 N should be used to repair the powder coatings. The notes and warnings of the manufacturer in question apply for handling of the selected materials. Please do not forget to protect the surfaces against use and manipulation until the curing time recommended by the relevant manufacturer for the materials processed has elapsed.

5 Passepartout Concrete 5/6 Maintenance Maintenance and care of the fibre concrete plates These recommendations will help refurbish the overall look of a damaged fibre concrete surface. We ask you, however, to consider that refurbishment to the original surface quality is unfortunately not possible. A tolerance of the repaired surfaces to substances which may be used to clean the surfaces must also be checked in each individual case and considered. The quality of the repairs made depends largely on the skill of the person making them. Unfortunately it is not possible to guarantee a particular result. For treating fibre concrete surfaces the following product can be used: Deep impregnator Item no C19/51 Fa. Poschacher Natursteinwerke GmbH & Co KG Poschacherstraße 7 A 4222 St. Georgen/Gusen T.: F.: office@poschacher.com The fibre concrete plates we used are made industrially from a high-strength, extremely dense material which is homogeneous in colour and consistency. At the factory, they are given a colourless protective coating, which gives the surfaces a perfect look and offers additional protection against weathering influences. Damage such as spalling, scratches, etc. does not negatively affect the durability of the material, however it compromises it visually - we call this patina. In order to counteract this, the material can be treated with the Poschacher deep impregnator. It seals the damaged places and makes them less visible. Depending on the scope of the repair work, the deep impregnator can be applied with the brush (for small places, e.g. individual scratches) or, for large applications, with the foam or lambskin roller. Soiling from pens or paints can be removed with a lot of water and damp sandpaper. To remove soiling, we recommend using a 100-grade sandpaper. Then a fine sanding should be done with a 400-grade sandpaper (or finer). After drying, the surface must be sealed with the deep impregnator. For more detailed information about using the deep impregnator, see the manufacturer s instructions. Please do not forget to protect the surfaces against use and manipulation until the curing time recommended by the relevant manufacturer for the materials processed has elapsed.

6 Passepartout Wood 6/6 Tenders Text for invitation of tenders Passepartout Concrete Preamble: All products listed and described below are protected by international design law. The transmission of these documents conveys no rights to existing design patents to the recipient or anyone else. Reproduction by a company other than public design GmbH is not allowed. Violations will be punished through legal means. The court of jurisdiction is Vienna, Austria. Passepartout Concrete: Furniture product line for public outdoor spaces consisting of bench without back rest and high table in 2 different dimensions. All furniture made of steel frames with seat and table surfaces of fibre concrete. All furniture is prepared for ground bolting or setting in concrete. Fibre concrete: Material strength 12mm, weight 110kg/m2, frost resistance according to EN 12467, flammability class A1 according to DIN 4102, water permeability according to EN 12467, wet and dry testing according to EN In 3 colour tones. Steel frame: Side parts made of lasered and welded steel plates and angle steel 73x40x5mm in the quality S235JRG2 EN 10025, hot-dip galvanised according to DIN EN ISO 1461 and Ö-Norm E 4015, minimum coating thickness according to DIN 50976, surfaces polished and free of zinc barbs and other unevenness; stained, chromated with 6-value chrome; high-temperature coating, UV-stable, coating thickness according to ISO 2360, adhesion force according to ISO 53151, crosscut adhesion value GT2, with structure surface due to high Teflon content; colour tone Graphite grey similar to DB 703 iron mica or RAL Side parts connected to one another by 4 formed tubes of non-rusting steel 30x20x1.5 mm material AISI 304 DIN Connection technology: Connection of the steel parts with safety screws with round-head and hexagonal recess M8 in INOX steel A2 according to ISO 7380 and locking nuts with polyamide insert M8 Inox A2 according to DIN 985. Connection of the fibre concrete sheets to the steel frame with safety screws with round-head and hexagonal recess M6 INOX A2 according to DIN 7380 as well as threaded sleeve M6.