Internal joint strap bedded in silicone mastic supplied by the manufacturer and secured with stainless steel bolts with coated heads.

Transcription

1 CI/SfB (52.5) lh4 Oct 2012 Arundel Range DATA SHEET Description This extruded aluminium gutter faithfully reproduces the shape of the Moulded 46 Ogee gutter which in cast iron was used on many traditional buildings. A range of sizes is offered so that there is gutter suitable for all applications from larger domestic to the biggest commercial and industrial buildings. long life without maintenance. As standard we supply the gutter without brackets for direct fixing, but brackets can be supplied if required for aesthetic reasons or for attaching to rafters where there is no fascia. The application of Polyester powder coating ensures a Specifying Information type: : Jointing: Fixing: Bailey ARUNDEL extruded aluminium gutter Internal joint strap bedded in silicone mastic supplied by the manufacturer and secured with stainless steel bolts with coated heads. To be securely screwed to timber fascia board of minimum thickness 22mm through pre-punched holes in the back of the gutter and accessories, with stainless steel screws and nylon washers supplied by the manufacturer.. Accessories: 90º/135º/Internal/external corners, stop ends, outlets, to suit downpipe size... Finish: Outside faces to be polyester powder coated to colour and gloss level selected from the Bailey range. (Consult Technical Department) Coating to be applied at manufacturer s in-house plant with 30 year guarantee available, subject to location. Fixing Instructions To be installed strictly in accordance with the manufacturer s instruction sheet available on request and sent out with each consignment.

2 General specifications SIZE 102x76 127x x x152 L Metal Thickness A B C º External Corner 90º Internal Corner Joint detail Running outlet Fascia bracket Stop end Flow rate chart Flow Litre/sec Outlet Capacity with central outlet Litres/sec. Roof area 102x dia. 102x x x x dia. 76 dia 102x x76 76 dia. 152 dia. 102x UK office Blatchford Close Horsham West Sussex RH13 5RF Tel +44 (0) sales@bailey-uk.com European office Tel +31 (0) sales@bailey-eu.com

3 CI/SfB (52.5) lh4 Oct 2012 Range DATA SHEET Description A range of extruded half round gutters with a unique flat rear face, allowing direct fixing to fascia, without additional brackets (except for the largest size, 150mm). With 3 sizes available this range fulfills the need for a high capacity half round system. Jointing is achieved with internal joint straps, leaving a clean unobstructed face. s are supplied polyester powder coated as standard, ensuring an extremely long, low maintenance life. Specifying Information type: : Jointing: Fixing: Accessories: Finish: Bailey CONWAY extruded deep flow half-round aluminium gutter. Internal joint straps bedded on silicone mastic supplied by the manufacturer and secured with stainless steel bolts with coated heads. Screwed to fascia board of minimum 22mm thickness through pre-punched holes at 600 centres in the back of the gutter with stainless steel screws and nylon washers supplied by the manufacturer. 90º/ 135º Internal/external corners, stop ends, running outlets to suit size... (see separate datasheet). Outside faces to be polyester powder coated to a colour and gloss level selected from the Bailey range (consult technical department). Coating to be applied at manufacturer s in-house plant with a 30 year guarantee available, subject to location. Fixing Instructions To be installed strictly in accordance with the manufacturer s instruction sheet available on request and sent out with each consignment.

4 General specifications SIZE L Metal Thickness A B C 100 x x x L 90º External Corner 90º Internal Corner A 100mm 100mm B C Running outlet Stop end 90 Corners illustrated. mm 50mm 135 and non standard are also available in external and internal. Fascia bracket (150x100mm only) Flow rate chart 161mm Outlet Capacity with central outlet Litres/sec. Roof area 100 x x x x x dia 72 x x x x x * Based on worst case category 1 rainfall in UK ( /5 m 2 ) UK office Blatchford Close Horsham West Sussex RH13 5RF Tel +44 (0) sales@bailey-uk.com European office Tel +31 (0) sales@bailey-eu.com

5 CI/SfB (52.5) lh4 Oct 2012 Corfe Cast DATA SHEET Description A cast aluminium half round gutter which reproduces the features of a traditional half round cast iron system. Installed in fascia or rafter brackets, jointing is achieved with a socket, which is normally on the left hand side looking at the building. Joints are bedded on silicone sealant and secured with a stainless steel bolt through the sole. Available in three sizes, this gutter is supplied as standard polyester powder coated to ensure a long maintenance free life. Specifying Information type: : Gauge: Jointing: Fixing: Accessories: Finish: Bailey Corfe cast aluminium half round gutter. Socket and spigot type. Joints to be bedded on silicone sealant and bolted with stainless steel bolts with coloured heads. Brackets to be screwed to fascia board/rafters at 900mm centres using stainless steel screws supplied by the manufacturer. 90 / 135 Internal / External / Corners. Running Outlets to suit downpipe size... (see separate datasheet). Stopends. Outside faces to be polyester powder coated to colour and gloss level selected from the Bailey range. (Consult Technical Department) Coating to be applied at manufacturer s in-house plant with 30 year guarantee available, subject to location. Fixing Instructions To be installed strictly in accordance with the manufacturer s instruction sheet available on request and sent out with each consignment.

6 General specifications GUTTER SIZE A B OUTLET C ø D 63/ / / /76/ º Corner Int/Ext E F G Outlet 90º External Corner 90º Internal Corner Specify R.H. or L.H. socket. Specify R.H. or L.H. socket. Stop end Fascia bracket Internal joint sleeve Rafter bracket Rafter brackets are available - please state side or top fix and angle of roof when ordering. Internal/External Flow rate chart GUTTER SIZE OUTLET SIZE C ø Capacity with central outlet Litres/sec. Roof area Consult Manufacturer UK office Blatchford Close Horsham West Sussex RH13 5RF Tel +44 (0) sales@bailey-uk.com European office Tel +31 (0) sales@bailey-eu.com

7 CI/SfB (52.5) lh4 Oct 2012 Durham Range DATA SHEET Description The Durham gutter is cast in aluminium to a traditional Ogee pattern which was extensively used in Victorian times in cast iron. This product can be used in refurbishment projects to match original specifications, or on new buildings where a very traditional style gutter is required. The Durham gutter, replicates the cast iron pattern including the spigot and socket joint detail. The gutter is supplied as standard with a long life polyester powder coating available in over 200 standard colours. It is installed by direct fixing through prepunched holes in the back of the gutter, or in fascia or rafter brackets. Specifying Information type: : Gauge: Jointing: Fixing: Accessories: Finish: Bailey Durham cast aluminium Ogee gutter. Socket and spigot type. Joints to be bedded on silicone sealant and bolted with stainless steel bolts with coloured heads. Brackets to be screwed to fascia board/rafters/at 900mm centres/or direct fixed through prepunched holes in the back of the gutter/using stainless steel screws supplied by the manufacturer. 90 / 135 Internal / External / Corners. Running Outlets to suit downpipe size... (see separate datasheet). Stopends. Outside faces to be polyester powder coated to colour and gloss level selected from the Bailey range. (Consult Technical Department) Coating to be applied at manufacturer s in-house plant with 30 year guarantee available, subject to location. Fixing Instructions To be installed strictly in accordance with the manufacturer s instruction sheet available on request and sent out with each consignment.

8 General specifications GUTTER SIZE A B OUTLET 90º Corner Int/Ext C ø D E F G 63/ / / Outlet 90º External Corner 90º Internal Corner Specify external or internal. (external shown). Specify external or internal. (Internal shown). Stop end Fascia bracket Internal joint sleeve Rafter bracket Rafter brackets are available - please state side or top fix and angle of roof when ordering. Internal/External Flow rate chart GUTTER SIZE OUTLET SIZE Capacity with central outlet Litres/sec. Roof area UK office Blatchford Close Horsham West Sussex RH13 5RF Tel +44 (0) sales@bailey-uk.com European office Tel +31 (0) sales@bailey-eu.com

9 CI/SfB (52.5) lh4 Oct 2012 Kenilworth Range DATA SHEET Description The Kenilworth gutter is one of a pair of profiled pressed aluminium gutters available in four standard sizes. They provide the hydraulic advantages of a box gutter but the profiled face gives some architectural interest, enabling the designer to make the gutter a feature of the building. The gutters have high flow capacity allowing the number of downpipes to be reduced, with consequent savings in drainage costs. As the gutters are direct fixed to a fascia board, no brackets are visible and the external joint strap requires no seen fixings, resulting in a smooth gutter line. The jointing system allows for the expansion and contraction of the aluminium over the complete temperature range experienced in the UK, so that expansion joints are not required even on the longest runs. The gutters are supplied as standard polyester powder coated on the outside faces giving a choice of over 200 standard colours and a long maintenance free life. Specifying Information type: : Gauge: Jointing: Fixing: Accessories: Finish: Bailey Kenilworth aluminium gutter. External joint straps assembled dry with gap for expansion. Joints are sealed internally with silicone sealant supplied by the manufacturer. To be screwed to fascia board of minimum thickness 22mm through pre-punched holes in back of gutter and accessories, with stainless steel screws and nylon washers supplied by the manufacturer. 90 / 135 Internal / External / Corners. Running Outlets to suit downpipe size... (see separate datasheet). Stopends. Outside faces to be polyester powder coated to colour and gloss level selected from the Bailey range. (Consult Technical Department) Coating to be applied at manufacturer s in-house plant with 30 year guarantee available, subject to location. Fixing Instructions To be installed strictly in accordance with the manufacturer s instruction sheet available on request and sent out with each consignment.

10 General specifications SIZE 80x x x x230 GUTTER ACCESSORIES L Metal Thickness A B C D E º External Corner 90º Internal Corner Running outlet Stop end 90 Corners illustrated. 135 and non standard are also available in external and internal. External joint strap Flow rate chart Flow Litre/sec Outlet Capacity with central outlet Litres/sec. Roof area 80x dia x x UK office Blatchford Close Horsham West Sussex RH13 5RF Tel +44 (0) sales@bailey-uk.com 170x European office Tel +31 (0) sales@bailey-eu.com

11 CI/SfB (52.5) lh4 Oct 2012 Lindisfarne Range DATA SHEET Description The Lindisfarne gutter is one of a pair of profiled pressed aluminium gutters available in four standard sizes. They provide the hydraulic advantages of a box gutter but the profiled face gives some architectural interest, enabling the designer to make the gutter a feature of the building. The gutters have high flow capacity allowing the number of downpipes to be reduced, with consequent savings in drainage costs. As the gutters are direct fixed to a fascia board no brackets are visible and the external joint strap requires no seen fixings, resulting in a smooth gutter line. The jointing system allows for the expansion and contraction of the aluminium over the complete temperature range experienced in the UK, so that expansion joints are not required even on the longest runs. The gutters are supplied as standard polyester powder coated on the outside faces giving a choice of over 200 standard colours and a long maintenance free life. Specifying Information type: : Gauge: Jointing: Fixing: Accessories: Finish: Bailey Lindisfarne aluminium gutter. External joint straps assembled dry with gap for expansion. Joints sealed internally with silicone sealant supplied by the manufacturer. To be screwed to fascia board of minimum thickness 22mm through pre-punched holes in back of gutter and accessories, with stainless steel screws and nylon washers supplied by the manufacturer. 90 / 135 Internal / External / Corners. Running Outlets to suit downpipe size... (see separate datasheet). Stopends. Outside faces to be polyester powder coated to colour and gloss level selected from the Bailey range. (Consult Technical Department) Coating to be applied at manufacturer s in-house plant with 30 year guarantee available, subject to location. Fixing Instructions To be installed strictly in accordance with the manufacturer s instruction sheet available on request and sent out with each consignment.

12 General specifications SIZE 85x x x x210 GUTTER ACCESSORIES L Metal Thickness A B C D E º External Corner 90º Internal Corner Running outlet Stop end 90 Corners illustrated. 135 and non standard are also available in external and internal. External joint strap Flow rate chart Flow Litre/sec Outlet Capacity without central outlet Litres/sec. Roof area 85x dia x x UK office Blatchford Close Horsham West Sussex RH13 5RF Tel +44 (0) sales@bailey-uk.com 175x European office Tel +31 (0) sales@bailey-eu.com

13 CI/SfB (52.5) lh4 Oct 2012 Stirling Range DATA SHEET Description The Bailey Stirling gutter range comprises five sizes of aluminium box gutter. Box gutters have the highest hydraulic capacity of any gutter type, the largest in the series giving a huge flow of over 17 litres per second. This allows the drainage engineer to reduce the number of downpipe drops with a consequent saving in drainage costs and also may enable the architect to keep an elevation clear of downpipes if required. The external joint strap system allows for expansion and contraction over the full climatic range of the U.K. without requiring separate expansion joints and also eliminates the unsightly nuts and bolt often associated with joints on this type of gutter. The entire range is available direct fix, with only the largest size utlizing integral support straps, which are not visible from below. The absence of brackets makes for a neat, attractive eaves line. All the gutters are produced from a substantial gauge of aluminium and for a long, maintenance free life are supplied as standard with the outside faces polyester powder coated. This gives the architect an almost infinite choice of colours. Specifying Information type: : Gauge: Jointing: Fixing: Accessories: Finish: (as standard) Bailey Stirling aluminium gutter. External joint straps assembled dry with gap for expansion. Joints sealed internally with silicone sealant supplied by the manufacturer. To be screwed to fascia board of minimum thickness 22mm through pre-punched holes in back of gutter and accessories, with stainless steel screws and nylon washers supplied by the manufacturer. 90 / 135 / Internal / External Corners. Running Outlets to suit downpipe size... (see separate datasheet). Stopends. Outside faces to be polyester powder coated to colour and gloss level selected from the Bailey range. (Consult Technical Department) Coating to be applied at manufacturer s in-house plant with 30 year guarantee available, subject to location. Fixing Instructions To be installed strictly in accordance with the manufacturer s instruction sheet available on request and sent out with each consignment.

14 General specifications SIZE 100x75 125x x x x200 GUTTER ACCESSORIES L Metal Thickness A B C D E º External Corner 90º Internal Corner Running outlet Stop end 90 Corners illustrated. 135 and non standard are also available in external and internal. External joint strap Flow rate chart Flow Litres/sec Outlet Capacity with central outlet Litres/sec. Roof area 100x x x x UK office Blatchford Close Horsham West Sussex RH13 5RF Tel +44 (0) sales@bailey-uk.com 200x dia 150x European office Tel +31 (0) sales@bailey-eu.com