RACO Commercial Fittings

Size: px
Start display at page:

Download "RACO Commercial Fittings"

Transcription

1 RACO Commercial Fittings

2 B2 GENERAL INFORMATION - STANDARDS, 1999 NATIONAL ELECTRICAL CODE General Information When you need to couple, connect, fasten, or ground conduit or cables, RACO fittings are your best answer. Choose from specification grade malleable iron, steel, lightweight aluminum, or economical die cast zinc materials. Many are UL Listed as rain-tight, concrete-tight, or liquidtight. : RACO Fittings RACO fittings are designed to save time on the job Locknuts won t slip or spin Hex-headed compression nuts lock tight on the conduit Premium set screws provide reliable continuity of ground Insulated throats protect insulation during wire pulling Fittings should be installed by licensed electricians in compliance with national and local electrical codes. Standards Where applicable, RACO products are engineered in accordance with the standards established by Underwriters Laboratories (UL). Most products are listed by UL and also certified by the Canadian Standards Association (CSA). Dimensional data listed in this catalog is intended for general reference with broad tolerance limits. RACO fittings generally conform to Federal Specifications and Standards A-A-50552, A-A-50553, A-A-50563, FF-S-760A(2), NEMA FB1-1998, U.L. 467, U.L. 514B, and CSA Standard C22.2 #18. Note: ANSI Standard C80-4 has been cancelled and replaced by NEMA FB-1. Underwriters Laboratories, Inc. file numbers: E rigid, IMC and liquidtight fittings; E EMT fittings; E non-metallic sheathed cable fittings; E service entrance cable fittings; E armored and flexible metal cable fittings; E outlet bushings and fittings; E grounding and bonding equipment; E67428 fixtures and fittings. For Underwriters Laboratories, Inc. and Canadian Standards Association listing marks, see RACO product and carton labels. Hazardous Locations RACO liquidtight conduit and cord connectors listed on pages B50-B66 are approved for use in hazardous locations by the National Electrical Code. Applications and the Code reference include: Class 1 Div. 2 where volatile liquids are handled or stored (501-4b) Class 2 Div. 1 where combustible dust is in the air (502-4a2) Class 2 Div. 2 where dust deposits may accumulate (502-4b2) Class 3 Div. 1 where easily ignitable fibers are manufactured or used (503-3a2) Class 3 Div. 2 where easily ignitable fibers are handled or stored (503-3b) The Code does not permit liquidtight connectors for Class 1, Div. 1, locations where volatile liquids and flammable gases are likely to be in the air. For installation guidelines and to learn more about RACO products, visit the NEMA website at The National Electrical Manufacturers Association (NEMA) website is a valuable electrical resource providing the information you need - quickly. Standards and technical information, installation guides, industry news and economic trends, events/meetings, the latest electroindustry, and legislative and regulatory information for more than fifty-one product areas ranging from arc welding to x-ray machines can be found with just a few clicks of your mouse. NEMA, celebrating its 75th anniversary in 2001, is the leading trade association in the United States representing the interests of electroindustry manufacturers. Founded in 1926 and headquartered near Washington, D.C., its 500 member companies manufacture products used in the generation, transmission and distribution, control, and end-use of electricity. Annual shipments of these products total $100 billion.

3 B3 GENERAL INFORMATION - STANDARDS, 1999 NATIONAL ELECTRICAL CODE 2 CONDUC- TORS 3 CONDUC- TORS CORD TYPE CORD SIZE CORD DIAMETER, PROX. CORD TYPE CORD SIZE CORD DIAMETER, PROX. PORTABLE CORD SELECTION CHART Refer to this chart when selecting cord connectors SVO, SV, SJ, SJO SVT SJT,SJTO S, SO, ST, STO #18 #18 #16 #14 #18 #16 #14 #12 #10 #8 #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 # SVO, SV, SJ, SJO SVT SJT,SJTO S, SO, ST, STO #18 #18 #16 #14 #18 #16 #14 #12 #10 #8 #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/0 #250 4 CONDUC- TORS CORD TYPE CORD SIZE CORD DIAMETER, PROX. CORD TYPE SJ, SJO, SJT,SJTO S, SO, ST, STO #18 #16 #14 #18 #16 #14 #12 #10 #8 #6 #4 #3 #2 #1 #1/0 #2/0 #3/0 #4/ CONDUC- TORS CORD TYPE CORD SIZE CORD DIAMETER, PROX. CORD TYPE S, SO, ST, STO #18 #16 #14 #12 #10 #8 #

4 B4 EMT STEEL SET SCREW CONNECTORS Applications For use in dry locations to bond EMT conduit to a box or enclosure RACO steel set screw connectors provide concrete-tight connections when taped RACO set screw connectors are suitable for applications above 600V All steel construction insures mechanical protection for the raceway Tri-head screws (1/2" to 1" trade sizes) may be installed using a slotted, Phillips, or Robertson head screwdriver 2-1/2" to 4" trade sizes are also UL listed for use on Rigid/IMC conduit, allowing for design and installation flexibility All components are zinc electroplated for corrosion protection Compliances 1/2"-2" C22.2 No /2"-4" 2-1/2"-4" C22.2 No. 18 UNINSULATED THROAT CONNECTORS STEEL ORDERING INFORMATION - SET SCREW CONNECTORS STEEL INSULATED UNINSULATED THROAT THROAT TRADE UNIT SHIP UPC SIZE /2" /2" /4" /4" " " " 1 10 INSULATED CONNECTORS STEEL /4" /2" " /2" " /2" " 1

5 EMT STEEL SET SCREW COUPLINGS B5 Applications For use in dry locations to couple two ends of EMT conduit RACO steel set screw couplings provide concrete-tight connections when taped RACO set screw couplings are suitable for applications above 600V All steel construction insures mechanical protection for the raceway Tri-head screws (1/2" to 1" trade sizes) may be installed using a slotted, Phillips, or Robertson head screwdriver 2-1/2" to 4" trade sizes are also UL listed for use on Rigid/IMC conduit, allowing for design and installation flexibility All components are zinc electroplated for corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances 1/2"-2" C22.2 No /2"-4" 2-1/2"-4" C22.2 No. 18 COUPLINGS STEEL ORDERING INFORMATION - COUPLINGS - STEEL UNIT SHIP UPC /2" /2" /4" /4" " " /4" /2" " /2" " /2" " 1

6 B6 EMT STEEL COMPRESSION CONNECTORS Applications For use to bond EMT conduit to a box or enclosure RACO 1/2" to 4" connectors provide concrete-tight connections RACO compression connectors are suitable for applications above 600V All steel construction insures mechanical protection for the raceway All components are zinc electro plated for corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances C22.2 No. 18 INSULATED THROAT CONNECTORS STEEL ORDERING INFORMATION - COMPRESSION CONNECTORS STEEL INSULATED UNINSULATED THROAT THROAT TRADE UNIT SHIP UPC SIZE /2" /2" /4" /4" " " 1 10 UNINSULATED CONNECTORS STEEL /4" /2" " /2" " /2" " 1

7 EMT STEEL COMPRESSION COUPLINGS B7 Applications For use to couple two ends of EMT conduit RACO 1/2" to 4" couplings provide concrete-tight connections RACO compression couplings are suitable for applications above 600V All steel construction insures mechanical protection for the raceway All components are zinc electro plated for corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliance C22.2 No. 18 ORDERING INFORMATION - COUPLINGS - STEEL COUPLINGS STEEL UNIT SHIP UPC /2" /2" /4" /4" " " /4" /2" " /2" " /2" " 1

8 B8 EMT STEEL INDENTER CONNECTORS Applications For use in dry locations to bond EMT conduit to a box or enclosure RACO indenter connectors provide concrete-tight connections when taped All steel construction insures mechanical protection for the raceway All components are zinc electroplated for corrosion protection INSULATED THROAT CONNECTORS STEEL ORDERING INFORMATION - UNINSULATED CONNECTORS STEEL INSULATED THROAT CONNECTORS - STEEL UNIT SHIP UPC /2" /4" UNINSULATED CONNECTORS - STEEL UNIT SHIP UPC /2" /4" A B C D E /2" 15/32" 13/16" 23/32" 25/32" /32" 17/32" 1-1/64" 15/16" 7/64" /64" 15/32" 13/16" 23/32" 25/32" /32" 17/32" 1-1/64" 15/16" 1-7/64" B = Thread length C = Body O.D. D = Body I.D. E = Length to conduit stop

9 EMT STEEL INDENTER CONNECTORS AND COUPLINGS, INDENTER TOOLS B9 Applications For use in dry locations to bond EMT conduit to a box or enclosure, or to couple two ends of EMT conduit RACO indenter offset connectors and couplings provide concretetight connections when taped All steel construction insures mechanical protection for the raceway All components are zinc electroplated for corrosion protection OFFSET CONNECTORS STEEL COUPLINGS STEEL ORDERING INFORMATION - INDENTER TOOLS FORGED STEEL COUPLINGS - STEEL UNIT SHIP UPC /2" /4" B=O.D. of body C=I.D. of body D = Length to center stop OFFSET CONNECTORS - STEEL A B C D " 25/32" 23/32" 31/32" /4" 1-1/64" 15/16" 1-1/16" UNIT SHIP UPC /2" 25 A B C D E F /16" 53/64" 23/32" 21/64" 3/8" 5/8" B=O.D. of body C=I.D. of body D = Thread length E=Amount of offset F=Throat I.D. INDENTER TOOLS FORGED - STEEL SHIP UPC DESCRIP. CTN. QTY. BAR CODE /2" Tool /4" Tool For No Replacement Point For No Replacement Point 10

10 B10 EMT DIE CAST SET SCREW CONNECTORS Applications For use in dry locations to economically bond EMT conduit to a box or enclosure RACO die cast set screw connectors provide concrete-tight connections when taped RACO set screw connectors are suitable for applications above 600V Rugged metallic construction provides mechanical protection for the raceway 2-1/2" to 4" trade sizes are UL Listed for use on Rigid/IMC conduit, allowing for installation flexibility Compliance C22.2 #18 B = Hub length, thread length and thread spec C=Throat I.D. D = Length to conduit stop E = Screw spec (type of head, length, thread spec) F = Body O.D. G = Body I.D. INSULATED THROAT CONNECTORS DIE CAST ZINC ORDERING INFORMATION - SET SCREW CONNECTORS STEEL INSULATED UNINSULATED CONNECTOR CONNECTOR SCREW A B C D E F G TYPE /8" 3/8" 5/8" 11/16" Slotted 15/16" 23/32" x 5/16" Robertson /8" 3/8" 13/16" 15/16" Slotted 1-5/32" 15/16" x 5/16" Robertson /2" 15/32" 1-3/64" 15/16" Slotted 1-7/16" 1-3/16" x 5/16" only /16" 19/32" 1-3/8" Long 1/ /32" 1-13/16" 1-17/32" Slotted x 7/16" Robertson /4" 3/4" 1-19/32" 1-7/16" /2" 3/4" 2-1/16" 1-3/4" /16" 1-1/16" 2-1/2" 2" /4" 1-1/32" 3-5/32" 2-1/8" /16" 1-3/8" 3-1/2" 2-3/16" UNINSULATED CONNECTORS DIE CAST ZINC INSULATED UNINSULATED CONNECTOR CONNECTOR TRADE UNIT SHIP UPC SIZE /2" /4" " /4" /2" " /2" " /2" /2" /4-20 x 7/16" 1/4-20 x 7/16" Long 2-1/16" 1-3/4" Slotted Robertson Long 2-9/16" 2-1/4" Slotted Robertson 1/ /32" 2-7/8" x 7/16" Slotted only 1/ /16" 3-17/32" Slotted x 7/16" only 1/ /32" 4-1/32" x 7/16" /16" 1-1/32" 4-5/32" 2-19/32" 1/ /32" 4-9/16" x 7/16" Slotted only Slotted only

11 EMT DIE CAST - SET SCREW - COUPLINGS AND OFFSETS B11 Couplings and Offset Connectors Applications RACO die cast set screw couplings provide concrete-tight connections when taped RACO set screw couplings are suitable for applications above 600V Couplings Application For use in dry locations to economically couple two ends of EMT conduit Offsets Connectors Application For use in dry locations to economically bond EMT conduit to a box or enclosure Couplings and Offset Connectors Product Feature Rugged metallic construction provides mechanical protection for the raceway Couplings Product Feature 2-1/2" to 4" trade sizes are UL Listed for use on Rigid/IMC conduit, allowing for installation flexibility Compliances C22.2 #18 B=O.D. of body C=I.D. of body D = Length to center stop E = Screw spec (type of head, length, thread spec) COUPLINGS DIE CAST ZINC ORDERING INFORMATION - COUPLINGS - DIE CAST ZINC UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 6 A B C D E SCREW TYPE /16" 29/32" 23/32" 3/4" x 5/16" Slotted Robertson /16" 13/16" 15/16" 15/16" x 5/16" Slotted Robertson /4" 1-13/32" 1-3/16" 1-1/8" x 5/16" Slotted Robertson /8" 1-13/16" 1-17/32" 1-5/16" 1/4-20 x 7/16" Long Slotted Robertson /16" 2-1/16" 1-3/4" 1-7/16" 1/4-20 x 7/16" Long Slotted Robertson /2" 2-1/2" 2-1/4" 1-3/4" 1/4-20 x 7/16" Long Slotted Robertson " 3-1/4" 2-15/16" 1-31/32" 1/4-20 x 7/16" Long Slotted Robertson /2" 3-29/32" 3-17/32" 2-7/32" 1/4-20 x 7/16" Long Slotted Robertson " 4-15/32" 4-1/32" 2-15/32" 1/4-20 x 7/16" Long Slotted Robertson /4" 4-31/32" 4-17/32" 2-19/32" 1/4-20 x 7/16" Slotted only OFFSET CONNECTORS - DIE CAST ZINC OFFSET CONNECTORS DIE CAST ZINC UNIT SHIP UPC /2" /4" 25 B=O.D. of body C=I.D. of body D = Thread length E=Angle of offset F=Screw spec (type of head, length, thread spec) G=Throat I.D. A B C D E F G /64" 61/64" 23/32" 3/8" x 5/16" 5/8" " 1-5/32" 15/16" 7/16" x 5/16" 13/16" SCREW TYPE Slotted screw 1/2-14 NPS Slotted screw 3/4-14 NPS

12 B12 EMT DIE CAST HANDY ELLS Applications For use in dry locations to bond EMT conduit to a box or enclosure, or to couple two ends of EMT conduit Use handy ells when bending conduit is not practical Product Feature Cover included Compliances 90 C22.2 #18 DEGREE HANDY ELLS DIE CAST ZINC COUPLINGS 90 DEGREE HANDY ELLS DIE CAST ZINC CONNECTORS ORDERING INFORMATION - 90 DEGREE HANDY ELLS - DIE CAST ZINC COUPLINGS UNIT SHIP UPC /2" /4" " 25 A = Width of body B=Throat I.D. C = Screw spec (type of head, length,thread spec) D = Overall length A B C D SCREW TYPE /8" 23/32" x 5/16" 1-7/8" Slotted Robertson, female to female /32" 15/16" x 5/16" 2-3/16" Slotted Robertson, female to female /8" 1-3/16" x 5/16" 3-1/8" Slotted, female to female 90 DEGREE HANDY ELLS - DIE CAST ZINC CONNECTORS UNIT SHIP UPC /2" /4" 5 50 SCREW A B C D E F TYPE /8" 23/32" x 5/16" 1-7/8" 3/8" 5/8" 1/2-14 NPS Slotted /32" 15/16" x 5/16" 2-3/16" 7/16" 13/16" 3/4-14 NPS Slotted A = Width of body B = Throat I.D. C = Screw spec (type of head, length, thread spec) D = Overall length E = Thread length and spec F = Throat I.D.

13 EMT DIE CAST COMPRESSION CONNECTORS B13 Applications For use to economically bond EMT conduit to a box RACO compression connectors are suitable for applications above 600V RACO 1/2" to 4" connectors provide concrete-tight connections Rugged metallic construction provides mechanical protection for the raceway Oversized hex compression nuts assure easy wrench installation Compliances C22.2 #18 B = Thread length and thread spec C=Throat I.D. D = Compression nut O.D. E = Compression nut I.D. F = Length to conduit stop INSULATED THROAT CONNECTORS DIE CAST ZINC ORDERING INFORMATION - THROAT CONNECTORS - DIE CAST ZINC INSULATED CONNECTOR UNINSULATED CONNECTOR A B THD. SPEC. C D E F /16" 3/8" 1/2-14 NPT 5/8" 1-7/64" 23/32" 53/64" /32" 27/64" 3/4-14 NPT 13/16" 1-25/64" 15/16" 53/64" /32" 33/64" /64" 37/64" /32" 3/4" /16" 3/4" /2 NPT 1-1/ /2 NPT 1-1/ /2 NPT /2 NPT UNINSULATED CONNECTORS DIE CAST ZINC INSULATED UNINSULATED CONNECTOR CONNECTOR TRADE UNIT SHIP UPC SIZE /2" /4" " /4" /2" " /2" " /2" /32" 1-11/16" 1-11/64" 31/32" 1-3/8" 2-5/32" 1-33/64" 15/16" 1-39/64" 2-13/32" 1-3/4" 1-7/16" 2-3/64" 2-15/16" 2-13/64" 1-21/32" /64" 1" 2-1/2-8 NPT 2-17/32" 3-17/32" 2-27/32" 1-11/16" " 1-1/8" 3-8 NPT 3-1/32" 4-7/32" 3-1/2" 1-25/32" /16" 15/16" 3-1/2-8 NPT 3-45/64" 5-1/16" 4-3/64" 1-23/32" /2" 1-1/16" 4-8 NPT 4-1/64" 5-5/32" 4-15/32" 2-1/4"

14 B14 EMT DIE CAST COMPRESSION COUPLINGS Applications For use to economically couple two ends of EMT conduit RACO compression couplings are suitable for applications above 600V RACO 1/2" to 4" couplings provide concrete-tight connections Rugged metallic construction provides mechanical protection for the raceway Hex compression nuts assure easy wrench installation Compliances C22.2 #18 B = Compression nut O.D. C = Compression nut I.D. D = Length to center stop COUPLINGS DIE CAST ZINC ORDERING INFORMATION - COUPLINGS - DIE CAST ZINC UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 6 A B C D /64" 1-7/64" 23/32" 27/32" /64" 1-13/32" 59/64" 13/16" /32" 1-11/16" 1-3/16" 31/32" " 2-11/64" 1-17/32" 31/32" /16" 2-13/32" 1-3/4" 1-1/2" /32" 2-13/16" 2-3/16" 1-17/32" /16" 3-17/32" 2-7/8" 1-45/64" /16" 4-3/16" 3-17/32" 1-3/4" /16" 4-3/4" 4-1/16" 1-27/32" /32" 5-5/16" 4-1/2" 1-7/8"

15 EMT DIE CAST COMPRESSION OFFSET CONNECTORS B15 Applications For use to economically bond EMT conduit to a box RACO compression offset connectors are suitable for applications above 600V Rugged metallic construction provides mechanical protection for the raceway Hex compression nuts assure easy wrench installation Compliances C22.2 #18 OFFSET CONNECTORS DIE CAST ZINC ORDERING INFORMATION - OFFSET CONNECTORS - DIE CAST ZINC UNIT SHIP UPC /2" /4" 25 B = Compression nut O.D. C = Compression nut I.D. D = Thread length and thread spec E=Amount of offset F=Throat I.D. A B C D E F THD. SPEC /32" 1-3/32" 23/32" 3/8" 3/8" 5/8" 1/2-14 NPS /64" 1-5/16" 61/64" 7/16" 3/4" 13/16" 3/4-14 NPS

16 B16 EMT DIE CAST/STEEL TWO-PIECE CONNECTORS AND COMBINATION COUPLINGS Die Cast Two-Piece Connectors Applications For use in dry locations to economically bond EMT conduit to a box or enclosure RACO 1/2" and 3/4" two-piece connectors provide concrete-tight connections Die Cast Two-Piece Connectors Product Feature Rugged metallic construction insures mechanical protection Die Cast Two-Piece Connectors Compliance Steel Combination Couplings Application Use RACO Cat. Nos when coupling threaded rigid/imc conduit to EMT Steel Combination Couplings Rugged metallic construction insures mechanical protection All steel components are zinc electro plated for corrosion protection Steel Combination Couplings Compliance TWO-PIECE CONNECTORS DIE CAST ZINC ORDERING INFORMATION - EMT RIGID COUPLINGS THREADED/COMPRESSION STEEL TWO-PIECE CONNECTORS - DIE CAST ZINC UNIT SHIP UPC /2" /4" 50 A B C D /16" 1-3/64" 15/16" 39/64" /16" 1-5/16" 1-5/32" 13/16" EMT RIGID COUPLINGS THREADED/COMPRESSION - STEEL UNIT SHIP UPC /2" /4" " 25 B=O.D. of nut C=O.D. of body D=I.D. of throat A B C D E /32" 3/4" 1-11/32" 1-1/8" 23/32" /16" 31/32" 1-17/32" 1-3/8" 15/16" /32" 1-7/32" 1-5/8" 1-43/64" 1-11/64" A=O.D. of hub B=Throat I.D. C = Overall length D = Nut O.D. E = Nut I.D.

17 EMT STEEL COMBINATION COUPLINGS B17 Application Use RACO Cat. Nos when coupling unthreaded rigid/ IMC to EMT Rugged metallic construction insures mechanical protection All steel components are zinc electro plated for corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation EMT RIGID COUPLINGS SET SCREW STEEL ORDERING INFORMATION - EMT RIGID COUPLINGS SET SCREW - STEEL UNIT SHIP UPC /2" /2" /4" /4" " " 1 15 B=O.D. rigid side C=I.D. rigid side D = O.D. EMT side E=I.D. EMT side F = Length to stop G=Screw spec A B C D E F G /16" 1" 7/8" 7/8" 23/32" 25/32" 1/4-28 x 3/8" Pan Head /16" 1" 7/8" 7/8" 23/32" 25/32" 1/4-28 x 3/8" Pan Head /8" 1-1/4" 1-5/64" 1-7/64" 15/16" 27/32" 1/4-28 x 3/8" Pan Head /8" 1-1/4" 1-5/64" 1-7/64" 15/16" 27/32" 1/4-28 x 3/8" Pan Head /32" 1-1/2" 1-11/32" 1-11/32" 1-3/16" 1-1/16" 1/4-28 x 3/8" Pan Head /32" 1-1/2" 1-11/32" 1-11/32" 1-3/16" 1-1/16" 1/4-28 x 3/8" Pan Head

18 B18 EMT MALLEABLE IRON/DIE CAST COMBINATION COUPLINGS Application Use RACO Cat. Nos or Cat. Nos when coupling flexible metal conduit to EMT Rugged metallic construction insures mechanical protection All steel/malleable components are zinc electro plated for corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances Certified A = Width across flex side B = Overall length C = Nut O.D. D = Nut I.D. E = Clamping range (flex side) EMT FLEX COUPLINGS SQUEEZE/COMPRESSION MALLEABLE IRON ORDERING INFORMATION - EMT-FLEX COUPLINGS SCREW-IN/COMPRESSION DIE CAST ZINC EMT FLEX COUPLINGS SQUEEZE/COMPRESSION - MALLEABLE IRON FLEX EMT UNIT SHIP UPC SIZE SIZE 1941* 3/8" 1/2" /2" 1/2" /2" 1/2" /4" 3/4" /4" 3/4" 1 20 *Not U.L. Listed A B C D E /4" 1-5/16" 1-7/64" 23/32" 17/32-5/8" /2" 1-3/4" 1-7/64" 23/32" 13/16-15/16" /2" 1-3/4" 1-7/64" 23/32" 13/16-15/16" /4" 1-53/64" 1-3/8" 15/16" 1-1/32-1-1/8" /4" 1-53/64" 1-3/8" 15/16" 1-1/32-1-1/8" EMT-FLEX COUPLINGS SCREW-IN/COMPRESSION - DIE CAST ZINC FLEX EMT UNIT SHIP UPC SIZE SIZE /2" 1/2" /4" 3/4" " 1" A " 1.10" " 1.30" " 1.62" B

19 EMT MALLEABLE IRON CLAMPBACKS B19 Applications For use with RACO straps to permit space between the conduit and the mounting surface Use of clamp backs in outdoor locations can prevent the buildup of snow and rain between the conduit and the mounting surface All malleable construction insures durability and mechanical protection Zinc electro plated for added corrosion protection Elongated bolt holes make alignment with straps easy For use in mounting EMT conduit in wet or dry locations B=Width C = Hole diameter D = Slot size E=Height CLAMP BACKS MALLEABLE IRON ORDERING INFORMATION - CLAMP BACKS - MALLEABLE IRON RIGID/IMC EMT UNIT SHIP UPC SIZE SIZE /2" 3/4" /4" 1" " 1-1/4" /4" 1-1/2" /2" 2" " 2" /2" 2-1/2" " 3" /2" 3-1/2" " 4" 5 A B C D E /16" 1" 13/32" 3/8 x 9/16" 7/16" /8" 1-1/32" 13/32" 7/16 x 9/16" 7/16" " 1-1/4" 3/8" 15/32 x 19/32" 9/16" /8" 1-15/32" 15/32" 1/2 x 3/4" 11/16" /32" 1-9/16" 7/16" 7/16 x 25/32" 1/2" /4" 1-15/16" 9/16" 5/8 x 29/32" 31/32" /8" 2-3/8" 1/2" 3/4 x 1" 7/8" /4" 2-9/16" 1/2" 3/4 x 1" 7/8" /16" 2-13/16" 1/2" 3/4 x 1" 1" /32" 2-15/16" 1/2" 3/4 x 1" 1"

20 B20 EMT STEEL STRAPS Application For use in mounting EMT conduit in wet or dry locations All steel construction insures mechanical protection RACO steel one-hole straps snap on to the conduit, allowing the installer to easily position the strap before mounting Oversized bolt holes make alignment of the fastener quick and easy All straps are zinc electro plated for corrosion protection ONE HOLE PUSH-ON STRAPS STAMPED STEEL ORDERING INFORMATION - ONE HOLE PUSH-ON STRAPS STAMPED - STEEL UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 10 A B C D E /8" 49/64" 1/4" 23/32" 5/8" /16" 1" 9/32" 59/64" 5/8" /16" 1-9/32" 9/32" 1-11/64" 3/4" /8" 1-41/64" 9/32" 1-17/32" 7/8" /8" 1-57/64" 11/32" 1-3/4" 1" /16" 2-25/64" 11/32" 2-3/16" 1-1/8" /16" 3-1/16" 21/32" 2-7/8" 1-1/4" /16" 3-11/16" 21/32" 3-1/2" 1-1/4" /8" 4-1/4" 21/32" 4" 1-1/4" /8" 4-3/4" 21/32" 4-1/2" 1-1/4" B=Height C = Hole size D=Diameter E=Width of strap

21 EMT STEEL STRAPS B21 Application For use in mounting EMT conduit in wet or dry locations All steel construction insures mechanical protection Oversized bolt holes make alignment of the fastener(s) quick and easy All straps are zinc electro plated for corrosion protection TWO HOLE STRAPS STAMPED STEEL ORDERING INFORMATION - TWO HOLE STRAPS STAMPED - STEEL UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 10 A B C D E F G " 2.140" 1.625".706".750".032" x.625".187" " 2.288" 1.715".922" 1.015".032" x.625".187" " 2.750" 2.140" 1.163" 1.235".036" x.750".250" " 3.520" 2.750" 1.510" 1.540".036" x.750".250" " 3.770" 3.141" 1.740" 1.785".036" x.750".250" " 4.453" 3.812" 2.147" 2.270".036" x.750".250" " 5.720" 4.680" 2.875" 3.050".059" x 1.000".312" " 6.578" 5.515" 3.500" 3.670".059" x 1.000".312" " 7.156" 6.125" 4.000" 3.975".059" x 1.000".312" " 7.718" 6.718" 4.500" 4.700".059" x 1.000".312"

22 B22 EMT MALLEABLE AND STEEL STRAPS Malleable-Straps Application For use in mounting EMT conduit in wet or dry locations Steel Straps Application For use in mounting EMT conduit Malleable Straps All malleable construction insures mechanical protection Oversized bolt holes make alignment of the fastener quick and easy All straps are zinc electro plated for corrosion protection Steel-Straps Product Feature Stamped steel straps are pregalvanized for added corrosion protection Steel-Straps Compliance ( ) ONE HOLE STRAPS MALLEABLE IRON ORDERING INFORMATION - ONE HOLE STRAPS - MALLEABLE IRON NAIL-UP STRAPS STAMPED STEEL UNIT SHIP UPC /2" " /2" " 5 B=Height C = Hole size D=Diameter E=Width of strap A B C D E /16" 3-9/32" 21/32" 2-7/8" 1-13/16" /2" 4" 21/32" 3-1/2" 2" /8" 4-1/2" 53/64" 4" 2-1/8" /8" 5-5/16" 3/4" 4-1/2" 2-1/4" NAIL-UP STRAPS STAMPED - STEEL UNIT SHIP UPC /2" /4" " A /16" 2-3/16" /4" 2-19/64" /2" 2-13/32" B A=Width of strap B=Height of strap

23 RIGID AND IMC STEEL SET SCREW CONNECTORS B23 Applications For use in dry locations to bond unthreaded rigid/imc conduit to a box or enclosure RACO steel set screw connectors are suitable for concrete-tight applications when taped Production Features All steel construction insures mechanical protection for the raceway 2-1/2" to 4" trade sizes are also UL Listed for use on EMT conduit, allowing for design and installation flexibility All components are zinc electro plated for corrosion protection Compliance B=Thread length and thread spec C=Throat I.D. D = Length to conduit stop E=Screw spec (type of head, length, thread spec) F = Body O.D. G = Body I.D. INSULATED THROAT CONNECTORS STEEL ORDERING INFORMATION - SET SCREW CONNECTORS - STEEL UNINSULATED INSULATED CONNECTOR CONNECTOR TRADE SIZE UNINSULATED CONNECTORS STEEL UNIT SHIP UPC CTN. CTN. BAR QTY. QTY. CODE /2" /4" " /4" /2" " /2" " /2" " 1 INSULATED UNINSULATED CONNECTOR CONNECTOR A B THD. SPEC. C D /64" 13/32" 1/2-14 NPS 39/64" 23/32" /64" 13/32" 3/4-14 NPS 53/64" 23/32" /2" 1/2" /2 NPS 1-3/64" 29/32" /16" 1/2" 1-1/4-11-1/2 NPS 1-25/64" 1-5/64" /32" 17/32" 1-1/2-11-1/2 NPS 1-39/64" 1-1/4" " 39/64" /2 NPS 2-3/32" 1-9/32" E SET SCREW Hex head screw 1/4-20 x 1/4" Hex head screw 1/4-20 x 1/4" Hex head screw 1/4-20 x 1/4" Hex head screw 5/16-24 x 5/16" Hex head screw 5/16-24 x 5/16" Hex head screw 5/16-24 x 5/16" F G 1-11/64" 55/64" 1-13/32" 1-5/64" 1-11/16" 1-11/32" 2-1/8" 1-11/16" 2-3/8" 2-15/16" 2-7/8" 2-7/16"

24 B24 RIGID AND IMC STEEL SET SCREW COUPLINGS Applications For use in dry locations to couple two ends of unthreaded rigid/imc conduit RACO steel set screw couplings are suitable for concrete-tight applications when taped Production Features All steel construction insures mechanical protection for the raceway 2-1/2" to 4" trade sizes are also UL Listed for use on EMT conduit, allowing for design and installation flexibility All components are zinc electro plated for corrosion protection Compliance B=O.D. of body C=I.D. of body D = Length to center stop E = Screw spec (type of head, length, thread spec) COUPLINGS STEEL ORDERING INFORMATION - COUPLINGS - STEEL UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 1 A B C D /2" 1-11/64" 55/64" 23/32" /2" 1-13/32" 1-5/64" 23/32" /8" 1-11/16" 1-11/32" 29/32" /16" 2-1/8" 1-11/16" 1-5/64" /32" 2-3/8" 1-15/16" 1-1/4" /16" 2-7/8" 2-7/16" 1-9/32" E THD. SPEC. Hex head screw 1/4-20 x 1/4" Hex head screw 1/4-20 x 1/4" Hex head screw 1/4-20 x 1/4" Hex head screw 5/16-24 x 5/16" Hex head screw 5/16-24 x 5/16" Hex head screw 5/16-24 x 5/16"

25 RIGID AND IMC STEEL/MALLEABLE IRON COMPRESSION CONNECTORS B25 Applications For use to bond unthreaded rigid/imc conduit to a box or enclosure RACO 1/2" to 4" connectors and couplings provide concretetight connectors All steel/malleable construction insures mechanical protection for the raceway Hex compression nuts assure easy wrench installation All components are zinc electro plated for corrosion protection Compliances C22.2 #18 ( ) B = Thread length and thread spec C=Throat I.D. D = Compression nut O.D. E = Compression nut I.D. F = Length to conduit stop UNINSULATED CONNECTORS STEEL/MALLEABLE IRON ORDERING INFORMATION - UNINSULATED CONNECTORS - STEEL/MALLEABLE IRON UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 1 A B THD. SPEC. C D E F /8" 33/64" 1/2-14 NPS 39/64" 15/32" 55/64" 27/32" /16" 35/64" 3/4-14 NPS 53/64" 1-7/16" 1-5/64" 29/32" /16" 5/8" /2 NPS 1-1/16" 1-3/4" 1-11/32" 31/32" /16" 21/32" 1-1/4-11-1/2 NPS 1-25/64" 2-5/32" 1-45/64" 1-1/8" /16" 23/32" 1-1/2-11-1/2 NPS 1-5/8" 2-3/8" 1-15/16" 1-1/4" /8" 21/32" /2 NPS 2-1/16" 3-1/16" 2-13/32" 1-1/2" /8" 15/16" 2-1/2-8 NPS 2-9/16" 3-15/16" 2-29/32" 2-13/16" " 1" 3-8 NPS 3-5/32" 4-21/32" 3-35/64" 2-7/8" /16" 1" 3-1/2-8 NPS 3-21/32" 5-13/64" 4-3/64" 3-1/8" /2" 1" 4-8 NPS 4-1/8" 5-3/4" 4-9/16" 3-3/8"

26 B26 RIGID AND IMC STEEL/MALLEABLE IRON COMPRESSION COUPLINGS Applications For use to couple two ends of conduit RACO 1/2" to 4" couplings provide concrete-tight connectors All steel/malleable construction insures mechanical protection for the raceway Hex compression nuts assure easy wrench installation All components are zinc electro plated for corrosion protection Compliances C22.2 #18 ( ) B = Compression nut O.D. C = Compression nut I.D. D = Length to center stop COUPLINGS STEEL/MALLEABLE IRON ORDERING INFORMATION - COUPLINGS - STEEL/MALLEABLE IRON UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 1 A B C D /4" 1-5/32" 55/64" 27/32" /16" 1-7/16" 1-5/64" 29/32" /16" 1-3/4" 1-11/32" 31/32" /16" 2-5/32" 1-45/64" 1-1/8" /32" 2-3/8" 1-15/16" 1-1/4" /32" 3-1/16" 2-13/32" 1-1/2" /4" 3-15/16" 2-29/32" 2-1/2" /32" 4-21/32" 3-35/64" 2-1/2" /2" 5-13/64" 4-3/64" 3-3/16" /16" 5-3/4" 4-9/16" 3-3/32"

27 RIGID AND IMC MALLEABLE - SHORT ELBOWS B27 Applications For use with threaded rigid/imc conduit 90 degree short elbows are ideal for use in tight locations where bending of conduit is not practical All malleable construction insures mechanical protection for the raceway All components are zinc electro plated for corrosion protection Compliance 90 DEGREE SHORT ELBOWS MALLEABLE IRON ORDERING INFORMATION - 90 DEGREE SHORT ELBOWS - MALLEABLE IRON UNIT SHIP UPC /2" /4" * 1" 10 * Not UL Listed G A B C D E F THREAD SPEC /64" 3/4" 1-1/16" 1-17/32" 1/2" 39/64" 1/2-14 NPS /32" 61/64" 1-9/32" 1-15/32" 9/16" 13/16" 3/4-14 NPS /64" 1-7/32" 1-21/32" 1-9/16" 1/2" 1-1/16" /2 NPS A = Hub O.D. B = Hub I.D. C=Length to end of hub D=Length to end of thread E = Thread length F=Throat I.D. G = Thread spec

28 B28 RIGID AND IMC DIE CAST HANDY ELLS Applications For use with threaded rigid/imc conduit to bond conduit to a box or enclosure, or to couple two ends of rigid/imc conduit Use handy ells when bending conduit is not practical Product Feature Gasket and cover included Compliance C22.2 #18 ( ) 90 DEGREE HANDY ELLS THREADED CONNECTORS DIE CAST ZINC 90 DEGREE HANDY ELLS THREADED COUPLINGS DIE CAST ZINC ORDERING INFORMATION - 90 DEGREE HANDY - ELLS THREADED CONNECTORS - DIE CAST ZINC UNIT SHIP UPC /2" /4" RAC 1 25 A = Width of body B=Throat I.D. C = Thread spec D = Overall length E = Thread length F=Throat I.D. C A B THD. SPEC. D E F /32" 49/64" 1/2-14 NPT 1-7/8" 3/8" 5/8" /32" 31/32" 3/4-14 NPT 2-3/16" 7/16" 13/16" 2664RAC 1-5/8" 1-7/32" 1-11/2 NPT 3-1/8" 9/16" 1-7/32" 90 DEGREE HANDY - ELLS THREADED COUPLINGS - DIE CAST ZINC UNIT SHIP UPC /2" /4" " /4" 20 A = Width of body B = Throat I.D. C = Thread spec D = Overall length A B C D /8" 49/64" 1/2-14 NPS 1-7/8" /32" 31/32" 3/4-14 NPS 2-1/4" /8" 1-7/32" 1-11/2 NPS 3-1/8" " 1-9/16" 1-1/4-11-1/2 NPS 3-1/4"

29 RIGID AND IMC MALLEABLE IRON HINGED COUPLINGS B29 Applications For use on threaded rigid/ IMC conduit Ideal for coupling runs of conduit that are closely spaced, where conduit is tight against a wall, or where conduit cannot be turned RACO hinged couplings provide concrete-tight connections All malleable construction insures mechanical protection of the raceway Unique tongue-in-groove design speeds installation All components are zinc electro plated for corrosion protection Compliance ORDERING INFORMATION - HINGED COUPLINGS - MALLEABLE IRON HINGED COUPLINGS MALLEABLE IRON UNIT SHIP UPC " /2" " /2" " " " 1 A B C " 2-5/8" 3-7/8" /16" 3-1/8" 4-3/4" /16" 3-7/8" 5-7/16" /16" 3-3/8" 5-15/16" /8" 3-15/16" 6-11/16" /2" 5" 7-15/16" " 6-1/8" 9-7/16" A = Width B = Diameter* C = Length

30 B30 RIGID AND IMC STEEL/MALLEABLE IRON THREE-PIECE COUPLINGS Applications For use with threaded rigid/ IMC conduit Use three-piece couplings to couple conduit ends when the conduit cannot be turned RACO three-piece couplings provide concrete-tight connections All steel/malleable construction insures mechanical protection of the raceway All components are zinc electro plated for corrosion protection Compliance B = O.D. body C = I.D. body D = Thread size THREE-PIECE COUPLINGS STEEL/MALLEABLE IRON ORDERING INFORMATION - THREE-PIECE COUPLINGS - STEEL/MALLEABLE IRON UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " " " 1 A B C D THD. SPEC /32" 1-7/32" 49/64" 1/2-14 NPT /8" 1-7/16" 31/32" 3/4-14 NPT /8" 1-3/4" 1-7/32" /2 NPT /16" 2-5/32" 1-9/16" 1-1/4-11-1/2 NPT /64" 2-3/4" 1-13/16" 1-1/2-11-1/2 NPT /32" 3-3/8" 2-9/32" /2 NPT /8" 4-1/16" 2-3/4" 2-1/2-8 NPT /8" 4-17/32" 3-3/8" 3-8 NPT /64" 5-3/16" 3-7/8" 3-1/2-8 NPT /32" 5-3/4" 4-3/8" 4-8 NPT /32" 6-3/4" 5-7/16" 5-8 NPT /64" 8-1/16" 6-1/2" 6-8 NPT

31 RIGID AND IMC STEEL COMBINATION COUPLINGS B31 Applications For use when coupling rigid/imc to EMT Use RACO Cat. Nos when coupling threaded rigid/imc conduit to EMT Use RACO Cat. Nos when coupling unthreaded rigid/imc to EMT All steel construction insures mechanical protection All components are zinc electro plated for corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliance ( only) A = O.D. of hub B = Throat I.D. C = Overall length D = Nut O.D. E = Nut I.D. RIGID EMT COUPLINGS THREADED/COMPRESSION STEEL ORDERING INFORMATION - RIGID EMT COUPLINGS THREADED/COMPRESSION - STEEL RIGID EMT COUPLINGS SET SCREW STEEL UNIT SHIP UPC /2" /4" " 25 A B C D E /32" 3/4" 1-11/32" 1-1/8" 23/32" /16" 31/32" 1-17/32" 1-3/8" 15/16" /32" 1-7/32" 1-5/8" 1-43/64" 1-11/64" RIGID EMT COUPLINGS SET SCREW - STEEL UNIT SHIP UPC /2" /2" /4" /4" " " 1 15 B = O.D. rigid side C = I.D. rigid side D = O.D. EMT side E = I.D. EMT side F = Length to stop G = Screw spec A B C D E F G /16" 1" 7/8" 7/8" 23/32" 25/32" /16" 1" 7/8" 7/8" 23/32" 25/32" /8" 1-1/4" 1-5/64" 1-7/64" 15/16" 27/32" /8" 1-1/4" 1-5/64" 1-7/64" 15/16" 27/32" /32" 1-1/2" 1-11/32" 1-11/32" 1-3/16" 1-1/16" /32" 1-1/2" 1-11/32" 1-11/32" 1-3/16" 1-1/16" 1/4-28 x 3/8" Pan Head 1/4-28 x 3/8" Pan Head 1/4-28 x 3/8" Pan Head 1/4-28 x 3/8" Pan Head 1/4-28 x 3/8" Pan Head 1/4-28 x 3/8" Pan Head

32 B32 RIGID AND IMC MALLEABLE COMBINATION COUPLINGS Application Use RACO Cat. Nos when coupling flexible metal conduit to threaded rigid/imc All malleable construction insures mechanical protection All components are zinc electro plated for corrosion protection Compliance RIGID FLEX COUPLINGS MALLEABLE IRON SQUEEZE/THREADED ORDERING INFORMATION - RIGID FLEX COUPLINGS - MALLEABLE IRON SQUEEZE/THREADED UNIT SHIP UPC /2" /4" " 25 D A B C THD. SPEC. E /8" 1-1/32" 3/4" 1/2-14 NPT 1-21/32" /8" 1-7/32" 31/32" 3/4-14 NPT 1-25/32" /16" 1-1/2" 1-7/32" 1-11/2 NPT 1-13/16" A = Width across flex side B= Hub O.D. C = Hub I.D. D = Thread spec hub E = Overall length

33 RIGID AND IMC DIE CAST THREADED HUBS B33 Applications For use with threaded rigid/imc conduit, to connect and bond conduit to a threadless opening in a box or enclosure May be used in wet or dry locations Rugged metallic construction insures mechanical protection Insulated throat protects wires and reduces wire pulling effort O-ring seals the assembly and provides a raintight seal Compliances C22.2 #18 THREADED HUBS INSULATED THROAT DIE CAST ZINC ORDERING INFORMATION - THREADED HUBS INSULATED THROAT - DIE CAST ZINC UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 2 A B C " 1/2-14 NPT /4-14 NPT /2 NPT /4-11-1/2 NPT /2-11-1/2 NPT /2 NPT /2-8 NPT NPT /2-8 NPT NPT B = O.D. C = Thread size

34 B34 RIGID AND IMC STEEL REDUCING BUSHINGS Application For use with threaded rigid/imc conduit to reduce the size of a female hub to accommodate a smaller size of conduit or male threaded hub Rugged steel construction insures mechanical protection of the raceway Zinc electro plated for corrosion protection Compliance REDUCING BUSHINGS STEEL ORDERING INFORMATION - REDUCING BUSHINGS - STEEL UNIT SHIP UPC /2-3/8" /4-1/2" /2" /4" /4-1/2" /4-3/4" /4-1" /2-1/2" /2-3/4" /2-1" /2-1-1/4" /2" /4" " /4" /2" 25 A = O.D./thread size B = Throat I.D./thread size C = Thickness A THD. SPEC. B THD. SPEC. C /16" 1/2-14 NPS 1/2" 3/8-18 NPS 17/32" /64" 3/4-14 NPS 39/64" 1/2-14 NPS 9/16" /32" /2 NPS 39/64" 1/2-14 NPS 5/8" /32" /2 NPS 13/16" 3/4-14 NPS 5/8" /8" 1-1/4-11-1/2 NPS 39/64" 1/2-14 NPS 11/16" /8" 1-1/4-11-1/2 NPS 13/16" 3/4-14 NPS 11/16" /8" 1-1/4-11-1/2 NPS 1-3/64" /2 NPS 11/16" /8" 1-1/2-11-1/2 NPS 39/64" 1/2-14 NPS 23/32" /8" 1-1/2-11-1/2 NPS 13/16" 3/4-14 NPS 23/32" /8" 1-1/2-11-1/2 NPS 1-3/64" /2 NPS 23/32" /8" 1-1/2-11-1/2 NPS 1-11/32" 1-1/4-11-1/2 NPS 23/32" /64" /2 NPS 39/64" 1/2-14 NPS 27/32" /64" /2 NPS 1-13/16" 3/4-14 NPS 27/32" /64" /2 NPS 1-3/64" /2 NPS 27/32" /64" /2 NPS 1-11/32" 1-1/4-11-1/2 NPS 27/32" /64" /2 NPS 1-19/32" 1-1/2-11-1/2 NPS 27/32"

35 RIGID AND IMC IRON REDUCING BUSHINGS B35 Application For use with threaded rigid/imc conduit to reduce the size of a female hub to accommodate a smaller size of conduit or male threaded hub Rugged iron construction insures mechanical protection of the raceway Zinc electro plated for corrosion protection REDUCING BUSHINGS IRON ORDERING INFORMATION - A = O.D./thread size B = Throat I.D./thread size C = Thickness REDUCING BUSHINGS - IRON UNIT SHIP UPC /2-1-1/4 " /2-1-1/2" /2-2" " /2" /2-2" /2-2-1/2" /2-3" " /2" 5 A THD. SPEC. B THD. SPEC. C /16" 2-1/2-8 NPT 1-11/32" 1-1/4-11-1/2 NPT 1-61/64" /16" 2-1/2-8 NPT 1-9/16" 1-1/2-11-1/2 NPT 2-9/64" /16" 2-1/2-8 NPT 2-1/64" /2 NPT 2-5/64" /32" 3-8 NPT 2-1/64" /2 NPT 2-3/32" /32" 3-8 NPT 2-13/32" 2-1/2-8 NPT 2-3/32" /32" 3-1/2-8 NPT 2-1/64" /2 NPT 2-3/32" /32" 3-1/2-8 NPT 2-13/32" 2-1/2-8 NPT 2-3/32" /32" 3-1/2-8 NPT 3" 3-8 NPT 2-3/32" /32" 4-8 NPT 3" 3-8 NPT 2-3/32" /32" 4-8 NPT 3-15/32" 3-1/2-8 NPT 2-3/32"

36 B36 RIGID AND IMC STEEL LOCKNUTS Application For use in dry locations on threaded rigid/imc conduit to secure conduit to a box or enclosure All steel construction insures mechanical protection Zinc electro plated for corrosion protection Compliances C22.2 #18 (3/8"-4" trade sizes) LOCKNUTS STEEL ORDERING INFORMATION - LOCKNUTS - STEEL UNIT SHIP UPC /8" /2" /4" " /4" /2" " /2" " /2" " " " 8 A = O.D. B = I.D. C = Thread size D = Thickness C A B THD. SPEC. D " 39/64" 3/8-18 NPT 5/32" /8" 49/64" 1/2-14 NPT 5/32" /8" 31/32" 3/4-14 NPT 11/64" /64" 1-15/64" /2 NPT 13/64" /16" 1-37/64" 1-1/4-11-1/2 NPT 7/32" /8" 1-13/16" 1-1/2-11-1/2 NPT 7/32" /64" 2-9/32" /2 NPT 15/64" /16" 2-3/4" 2-1/2-8 NPT 3/8" /4" 3-3/8" 3-8 NPT 3/8" /16" 3-7/8" 3-1/2-8 NPT 3/8" /32" 4-3/8" 4-8 NPT 3/8" /64" 5-7/16" 5-8 NPT 1/2" /16" 6-1/2" 6-8 NPT 9/16"

37 RIGID AND IMC STEEL LOCKNUTS B37 Application For use in dry locations on threaded rigid/imc conduit to secure conduit to a box or enclosure All steel construction insures mechanical protection Zinc electro plated for corrosion protection NON-UL LOCKNUTS STEEL ORDERING INFORMATION - A = O.D. B = I.D. C = Thread size D = Thickness NON - UL LOCKNUTS - STEEL UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 10 C A B THD. SIZE D /8" 49/64" 1/2-14 NPT 9/64" /8" 31/32" 3/4-14 NPT 5/32" /64" 1-15/64" /2 NPT 3/16" /16" 1-37/64" 1-1/4-11-1/2 NPT 13/64" /8" 1-13/16" 1-1/2-11-1/2 NPT 13/64" /64" 2-9/32" /2 NPT 13/64" /64" 2-3/4" 2-1/2-8 NPT 9/32" /8" 3-3/8" 3-8 NPT 5/16" /16" 3-7/8" 3-1/2-8 NPT 5/16" /4" 4-3/8" 4-8 NPT 5/16"

38 B38 RIGID AND IMC STEEL BONDING LOCKNUTS Applications For use on threaded rigid/ IMC conduit Use bonding locknuts when additional locking and grounding connections are required in applications where severe vibration is encountered All steel construction insures mechanical protection Zinc electro-plated for corrosion protection Compliances C22.2 #18 BONDING LOCKNUTS - MALLEABLE IRON BONDING LOCKNUTS STEEL ORDERING INFORMATION - UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 5 A B C THD. SPEC " /2-14 NPT x 1/ " /4-14 NPT x 1/ /2 NPT x 1/ /4-11-1/2 NPT x 1/ /2-11-1/2 NPT x 1/ /2 NPT x 1/ /2-8 NPT x 31/ NPT x 31/ /2-8 NPT x 31/ NPT x 31/32 D E A = O.D. B = I.D. C = Thread size D = Thickness E = Screw spec

39 RIGID AND IMC STEEL SEALING LOCKNUTS B39 Applications For use with threaded rigid/imc conduit to provide a positive seal against water and oil RACO sealing locknuts may be used with either sheet metal or cast enclosures Fused-in-place gasket guarantees a rain-tight seal Use a RACO sealing locknut as an economical alternative to a threaded enclosure connector All steel construction insures mechanical protection Zinc electro plated for corrosion protection Compliances ( ) C22.2 #18 ( ) A = O.D. B = I.D. C = Thread size D = Thickness SEALING LOCKNUTS STEEL ORDERING INFORMATION - SEALING LOCKNUTS - STEEL UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 10 A B C THD. SPEC /64" 49/64" 1/2-14 NPT 7/32" /64" 31/32" 3/4-14 NPT 7/32" /4" 1-15/64" /2 NPT 1/4" /32" 1-37/64" 1-1/4-11-1/2 NPT 17/64" /32" 1-13/16" 1-1/2-11-1/2 NPT 17/64" /64" 2-9/32" /2 NPT 9/32" /16" 2-3/4" 2-1/2-8 NPT 5/16" /8" 3-3/8" 3-8 NPT 3/8" /16" 3-7/8" 3-1/2-8 NPT 3/8" /4" 4-3/8" 4-8 NPT 3/8" D

40 B40 RIGID AND IMC STEEL/MALLEABLE IRON BUSHINGS Applications For use on threaded rigid/ IMC conduit Bushings provide a smoothly rounded surface at the entrance of raceways Steel/malleable iron construction insures mechanical protection Zinc electro plated for corrosion protection Compliances C22.2 #18 BUSHINGS STEEL/MALLEABLE IRON ORDERING INFORMATION - A = O.D. across corners B = I.D. C = Thread size D=Thickness BUSHINGS STEEL/MALLEABLE IRON UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " " " 5 C A B THD. SPEC. D /8" 5/8" 1/2-14 NPT 1/2" /32" 13/16" 3/4-14 NPT 1/2" /16" 1-3/64" /2 NPT 1/2" /8" 1-3/8" 1-1/4-11-1/2 NPT 17/32" /8" 1-39/64" 1-1/2-11-1/2 NPT 17/32" /8" 2-1/16" /2 NPT 21/32" /4" 2-29/64" 2-1/2-8 NPT 3/4" /8" 3-3/64" 3-8 NPT 3/4" /2" 3-35/64" 3-1/2-8 NPT 7/8" /8" 4-1/64" 4-8 NPT 29/32" /4" 5" 5-8 NPT 1-1/32" /4" 6" 6-8 NPT 1-3/32"

41 RIGID AND IMC POLYPROPYLENE INSULATED BUSHINGS B41 Applications For use on threaded rigid/ IMC conduit Bushings provide a smoothly rounded surface at the entrance of raceways Product Feature Insulating bushings are made of high impact polypropylene that is temperature rated at 105 C Compliances C22.2 #18 INSULATING BUSHINGS POLYPROPYLENE ORDERING INFORMATION - INSULATING BUSHINGS - POLYPROPYLENE UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " " " 5 A = O.D. B = I.D. C = Thread size D = Thickness C A B THD. SPEC. D /16" 19/32" 1/2-14 NPT 25/64" /32" 51/64" 3/4-14 NPT 25/64" /16" 1" /2 NPT 9/16" /64" 1-21/64" 1-1/4-11-1/2 NPT 9/16" /16" 1-35/64" 1-1/2-11-1/2 NPT 9/16" /16" 2" /2 NPT 5/8" /16" 2-13/32" 2-1/2-8 NPT 43/64" /32" 3" 3-8 NPT 3/4" /64" 3-13/32" 3-1/2-8 NPT 3/4" /32" 3-29/32" 4-8 NPT 49/64" /8" 4-59/64" 5-8 NPT 1" /2" 5-57/64" 6-8 NPT 1"

42 B42 RIGID AND IMC STEEL/MALLEABLE IRON INSULATED BUSHINGS Application For use on threaded rigid/imc conduit to provide a smoothly rounded surface at the entrance of raceways Insuliner temperature rated at 105 C Steel/malleable construction insures mechanical protection for the raceway Zinc electro plated for corrosion protection Compliances C22.2 #18 INSULATED BUSHINGS STEEL/MALLEABLE IRON ORDERING INFORMATION - INSULATED BUSHINGS - STEEL/MALLEABLE IRON UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 5 A B C THD. SPEC /8" 9/16" 1/2-14 NPT 17/32" /32" 3/4" 3/4-14 NPT 17/32" /16" 31/32" /2 NPT 17/32" /8" 1-1/4" 1-1/4-11-1/2 NPT 37/64" /8" 1-15/32" 1-1/2-11-1/2 NPT 37/64" /8" 1-31/32" /2 NPT 45/64" /4" 2-23/64" 2-1/2-8 NPT 27/32" /8" 2-59/64" 3-8 NPT 27/32" /2" 3-3/8" 3-1/2-8 NPT 1" /8" 3-27/32" 4-8 NPT 1-1/32" D A = O.D. across corners B = I.D. C = Thread size D=Thickness

43 RIGID AND IMC STEEL/MALLEABLE IRON INSULATED GROUNDING BUSHINGS B43 Application For use on threaded rigid/imc conduit to provide a means of grounding conduit through an insulated bushing Lay-in lug style provides an easy means of inserting a ground wire Dual rated aluminum grounding lugs may be used with copper or aluminum grounding conductors Insuliner temperature rated at 105 C Steel/malleable construction insures mechanical protection for the raceway Zinc electro plated for corrosion protection Compliance TRADE SIZE INSULATED GROUNDING BUSHINGS LAY-IN LUG STEEL/MALLEABLE IRON ORDERING INFORMATION - INSULATED GROUNDING BUSHINGS LAY-IN LUG STEEL - MALLEABLE IRON UNIT SHIP GROUNDING UPC CTN. CTN. WIRE CAPACITY BAR QTY. QTY. MIN. MAX. CODE /2" 100 #14 Sol. #4 Str /4" 100 #14 Sol. #4 Str " 50 #14 Sol. #4 Str /4" 25 #14 Sol. #4 Str /2" 25 #14 Sol. #4 Str " 10 #14 Sol. #4 Str /2" 10 #14 Sol. #1/0 Str " 5 #14 Sol. #1/0 Str /2" 5 #6 Str. #250 MCM " 5 #6 Str. #250 MCM C A B THD. SPEC. D E F G H I x 1/4" x 1/4" 1/4-28 x 5/8" /8" 9/16" 1/2-14 NPS 17/32" 1-1/16" 3/8" Set Screw Pan Head Screw Set Screw /32" 3/4" 3/4-14 NPS 17/32" 1-1/16" 3/8" /16" 31/32" /2 NPS 17/32" 1-1/16" 3/8" /8" 1-1/4" 1-1/4-11-1/2 NPS 37/64" 1-1/16" 3/8" /8 1-15/32 1-1/2-11-1/2 NPS 37/64" 1-1/16" 3/8" /8" 1-31/32" /2 NPS 45/64" 1-1/16" 3/8" /4" 2-23/64" 2-1/2-8 NPS 27/32 1-1/2" 19/32" /8" 2-59/64" 3-8 NPS 27/32" 1-1/2" 19/32" /2" 3-3/8" 3-1/2-8 NPS 1" 2-13/64" 51/64" /8" 3-27/32" 4-8 NPS 1-1/32" 2-13/64" 51/64" x 1/4" x 1/4" 1/4-28 x 5/8" Set Screw Pan Head Screw Set Screw x 1/4" x 1/4" 1/4-28 x 5/8" Set Screw Pan Head Screw Set Screw x 1/4" x 1/4" 1/4-28 x 5/8" Set Screw Pan Head Screw Set Screw x 1/4" x 1/4" 1/4-28 x 5/8" Set Screw Pan Head Screw Set Screw x 1/4" x 1/4" 1/4-28 x 5/8" Set Screw Pan Head Screw Set Screw x 5/16" 1/4-20 x 3/8" 3/8-24 x 7/8" Set Screw Pan Head Screw Set Screw x 5/16" 1/4-20 x 3/8" 3/8-24 x 7/8" Set Screw Pan Head Screw Set Screw 5/16-24 x 3/8" 5/16-24 x 17/32" 9/16-18 x 1-1/4" Set Screw Pan Head Screw Set Screw 5/16-24 x 7/16" 5/16-24 x 17/32" 9/16 18 x 1-1/4" Set Screw Pan Head Screw Set Screw A = O.D. across corners B = I.D. C = Thread size D = Thickness E = Height of lug F = Width of lug G = Screw spec, bonding screw H = Screw spec, screw that holds lug to bushing I = Screw spec, screw that holds ground wire

44 B44 RIGID AND IMC STEEL/MALLEABLE IRON INSULATED GROUNDING BUSHINGS Application For use on threaded rigid/imc conduit to provide a means of grounding conduit through an insulated bushing Feed-thru lug style provides an easy means of inserting a ground wire Dual rated aluminum grounding lugs may be used with copper or aluminum grounding conductors Insuliner temperature rated at 105 C Steel/malleable construction insures mechanical protection for the raceway Zinc electro plated for corrosion protection Compliance INSULATED GROUNDING BUSHINGS FEED-THRU LUG STEEL/MALLEABLE IRON ORDERING INFORMATION - INSULATED GROUNDING BUSHINGS FEED-THRU LUG - STEEL - MALLEABLE IRON TRADE SIZE UNIT SHIP GROUNDING UPC CTN. CTN.. WIRE CAPACITY BAR QTY. QTY. MIN. MAX. CODE /2" 100 #14 Sol. #4 Str /4" 100 #14 Sol. #4 Str " 50 #14 Sol. #4 Str /4" 25 #14 Sol. #4 Str /2" 25 #14 Sol. #4 Str " 10 #14 Sol. #4 Str /2" 10 #14 Sol. #1/0 Str " 5 #14 Sol. #1/0 Str /2" 5 #6 Str. #250 MCM " 5 #6 Str. #250 MCM C A B THD. SPEC. D E F G H I x 1/4" x 7/32" 1/4-28 x 3/8" /8" 9/16" 1/2-14 NPS 17/32" 1-1/16" 1/2" Set Screw Pan Head Screw Set Screw /32" 3/4" 3/4-14 NPS 17/32" 1-1/16" 1/2" /16" 31/32" /2 NPS 17/32" 1-1/16" 1/2" /8" 1-1/4" 1-1/4-11-1/2 NPS 37/64" 1-1/16" 1/2" /8" 1-15/32" 1-1/2-11-1/2 NPS 37/64" 1-1/16" 1/2" /8" 1-31/32" /2 NPS 45/64" 1-1/16" 1/2" /4" 2-23/64" 2-1/2-8 NPS 27/32" 1-15/32" 5/8" /8" 2-59/64" 3-8 NPS 27/32" 1-15/32" 5/8" /2" 3-3/8" 3-1/2-8 NPS 1" 1-3/4" 27/32" /8" 3-27/32" 4-8 NPS 1-1/32" 1-3/4" 27/32" x 1/4" x 7/32" 1/4-28 x 3/8" Set Screw Pan Head Screw Set Screw x 1/4" x 1/4" 1/4-28 x 3/8" Set Screw Pan Head Screw Set Screw 10-32x 1/4" x 1/4" 1/4-28 x 3/8" Set Screw Pan Head Screw Set Screw x 1/4" x 1/4" 1/4-28 x 3/8" Set Screw Pan Head Screw Set Screw x 1/4" x 1/4" 1/4-28 x 3/8" Set Screw Pan Head Screw Set Screw 5/16-24 x 3/8" 5/16-24 x 3/8" 7/16-20 x 3/8" Set Screw Pan Head Screw Set Screw 5/16-24 x 3/8" 5/16-24 x 3/8" 7/16-20 x 3/8" Set Screw Pan Head Screw Set Screw 5/16-24 x 3/8" 5/16-24 x 27/64" 5/8-18 x 11/16" Set Screw Pan Head Screw Set Screw 5/16-24 x 7/16" 5/16-24 x 27/64" 5/8-18 x 11/16" Set Screw Pan Head Screw Set Screw A = O.D. B = I.D. C=Thread size D = Thickness E = Height of lug F = Width of lug G = Screw spec bonding screw H = Screw spec screw that holds lug to bushing I = Screw spec screw that holds ground wire

45 RIGID AND IMC MALLEABLE IRON 150 C INSULATED GROUNDING BUSHINGS B45 Application For use on threaded rigid/imc conduit to provide a means of grounding conduit through an insulated bushing Lay-In style of grounding allows for easy insertion of grounding connector Dual rated aluminum grounding lugs may be used with copper or aluminum grounding conductors Insuliner temperature rated at 150 C will not soften or become dislodged during wire pulling Malleable construction insures mechanical protection for the raceway Zinc electro plated for corrosion protection Compliances Standard 514B C22.2 #18 ORDERING INFORMATION C INSULATED GROUNDING BUSHINGS LAY-IN LUG - STEEL/MALLEABLE IRON 150 INSULATED GROUNDING BUSHINGS FEED-THRU LUG STEEL/MALLEABLE IRON TRADE SIZE UNIT SHIP GROUNDING UPC CTN. CTN. WIRE CAPACITY BAR QTY. QTY. MIN. MAX. CODE /2" 100 #14 Sol. #4 Str /4" 100 #14 Sol. #4 Str " 50 #14 Sol. #4 Str /4" 25 #14 Sol. #4 Str /2" 25 #14 Sol. #2 Str " 10 #14 Sol. #2 Str /2" 10 #14 Sol. 1/ " 5 #14 Sol. 1/ /2" 5 #6 Str. 250 MCM " 5 #6 Str. 250 MCM TRADE SIZE A B C /2" /4" " /4" /2" " /2" " /2" " A = Lug Bushing Width B=O.D. Bushing C=Thickness

46 B46 RIGID AND IMC STEEL STRAPS Applications For use in mounting rigid/imc conduit in wet or dry locations RACO Rigid/IMC conduit straps are suitable for use on liquidtight flexible metal conduit and liquidtight flexible nonmetallic conduit (type B) All steel construction insures mechanical protection RACO steel one-hole straps snap on to conduit, allowing the installer to easily position the strap before mounting All straps are zinc electro plated for corrosion protection ONE HOLE PUSH-ON STRAPS STAMPED STEEL ORDERING INFORMATION - ONE HOLE PUSH-ON STRAPS - STAMPED STEEL UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " 10 A B C D E /64" 7/8" 9/32" 55/64" 7/8" /16" 1-3/32" 9/32" 1-1/16" 3/4" /16" 1-1/4" 9/32" 1-5/16" 3/4" /8" 1-5/8" 11/32" 1-5/8" 7/8" /32" 1-7/8" 13/32" 1-15/16" 7/8" /16" 2-7/16" 13/32" 2-3/8" 7/8" /16" 3" 21/32" 2-7/8" 1-1/4" /16" 3-9/16" 21/32" 3-1/2" 1-1/4" /8" 3-7/8" 21/32" 4" 1-1/4" /8" 4-1/4" 21/32" 4-1/2" 1-1/4" B = Height C = Hole size D = Diameter E=Width of strap

47 RIGID AND IMC MALLEABLE IRON STRAPS B47 Applications For use in mounting rigid/imc conduit in wet or dry locations RACO Rigid/IMC conduit straps are suitable for use on liquidtight flexible metal conduit and liquidtight flexible nonmetallic conduit (type B) All malleable construction insures mechanical protection All straps are zinc electro plated for corrosion protection ONE HOLE STRAPS MALLEABLE IRON ORDERING INFORMATION - ONE HOLE STRAPS - MALLEABLE IRON UNIT SHIP UPC /8" /2" /4" " /4" /2" " /2" " /2" " 5 A B C D E /8" 25/32" 11/32" 11/16" 21/32" /32" 7/8" 11/32" 7/8" 3/4" /2" 1-3/32" 11/32" 1-5/64" 25/32" /32" 1-13/32" 3/8" 1-11/32" 15/16" /64" 1-43/64" 15/32" 1-11/16" 1" /16" 2" 13/32" 1-15/16" 1-1/8" /8" 2-9/16" 19/32" 2-3/8" 1-7/16" /16" 3-9/32" 21/32" 2-7/8" 1-13/16" /2" 4" 21/32" 3-1/2" 2" /8" 4-1/2" 53/64" 4" 2-1/8" /8" 5-5/16" 3/4" 4-1/2" 2-1/4" B = Height C = Hole size D = Diameter E=Width of strap

48 B48 RIGID AND IMC STEEL STRAPS Applications For use in mounting rigid/imc conduit in wet or dry locations RACO Rigid/IMC conduit straps are suitable for use on liquidtight flexible metal conduit and liquidtight flexible nonmetallic conduit (type B) All steel construction insures mechanical protection All straps are zinc electro plated for corrosion protection TWO HOLE STRAPS STAMPED STEEL ORDERING INFORMATION - B = Overall height C = Strap width D = Hole diameter E = Diameter TWO HOLE STRAPS - STAMPED STEEL UNIT SHIP UPC /2" /4" " /4" /2" " /2" " /2" " " " 5 A B C D E /16" 7/8" 19/32" 3/16" 13/16" /8" 1-1/8" 19/32" 3/16" 1-1/16" /16" 1-31/32" 23/32" 1/4" 1-5/16" /4" 1-11/16" 23/32" 1/4" 1-21/32" /8" 1-7/8" 23/32" 1/4" 1-7/8" " 2-7/16" 23/32" 17/64" 2-3/8" /4" 3-1/8" 1" 5/16" 2-7/8" /32" 3-11/16" 1" 5/16" 3-35/64" /2" 3-15/16" 1" 5/16" 4-3/64" /8" 4-11/16" 1" 5/16" 4-35/64" /16" 5-43/64" 1-1/4" 21/32" 5-49/64" /64" 6-19/32" 1-1/4" 21/32" 7"

49 RIGID AND IMC MALLEABLE IRON CLAMP BACKS B49 Applications For use with RACO straps to permit space between the conduit and the mounting surface Use of clamp backs in outdoor locations can prevent the buildup of snow and rain between the conduit and the mounting surface All malleable construction insures durability and mechanical protection Elongated bolt holes make alignment with straps easy Zinc electro plated for corrosion protection CLAMP BACKS MALLEABLE IRON ORDERING INFORMATION - B = Width C = Hole diameter D = Slot size E = Height CLAMP BACKS - MALLEABLE IRON UNIT SHIP UPC RIGID SIZE EMT SIZE /2" 3/4" /4" 1" " 1-1/4" /4" 1-1/2" /2" 2" " 2" /2" 2-1/2" " 3" /2" 3-1/2" " 4" 5 A B C D E /16" 1" 13/32" 3/8 x 9/16" 7/16" /8" 1-1/32" 13/32" 7/16 x 9/16" 7/16" " 1-1/4" 3/8" 15/32 x 19/32" 9/16" /8" 1-15/32" 15/32" 1/2 x 3/4" 11/16" /32" 1-9/16" 7/16" 7/16 x 25/32" 1/2" /4" 1-15/16" 9/16" 5/8 x 29/32" 31/32" /8" 2-3/8" 1/2" 3/4 x 1" 7/8" /4" 2-9/16" 1/2" 3/4 x 1" 7/8" /16" 2-13/16" 1/2" 3/4 x 1" 1" /32" 2-15/16" 1/2" 3/4 x 1" 1"

50 B50 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS STEEL/MALLEABLE IRON STRAIGHT CONNECTORS Applications For use in outdoor or indoor locations on flexible metallic liquidtight conduit and Type B flexible nonmetallic liquidtight conduit Use to positively bond the conduit to a box or enclosure RACO liquidtight connectors are suitable for use in Class 1, Division 2; Class 2, Division 1 and 2; and Class 3, Division 1 and 2 hazardous locations Patented split gland-ring is designed to slip onto the conduit quickly and to grip the jacket of the conduit, speeding installation, assuring a perfect seal, and preventing pullouts Screw machined bodies (straight through 1") and precision threaded malleable iron castings mate with other components perfectly without strain or distortion All components are reusable RACO liquidtight connectors may be easily disassembled and reused after years of service Sealing washer (included) provides a liquidtight seal when terminating the connector in a threadless opening Heavy duty locknut included with every RACO liquidtight connector assures continuity of ground All metallic components are zinc electro plated for added corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances C22.2 #18 STRAIGHT-INSULATED STEEL/MALLEABLE IRON ORDERING INFORMATION - STRAIGHT - INSULATED AND UNINSULATED - STEEL/MALLEABLE IRON INSULATED UNINSULATED IRON IRON TRADE UNIT SHIP UPC SIZE 3511* 3/8" * 3/8" /2" /2" /4" /4" " " / /2" " /2" " /2" " 1 *1/2" Trade size hub TRADE SIZE A B STRAIGHT-UNINSULATED STEEL/MALLEABLE IRON THREAD SPEC. 3/8" 1-1/16" 19/32 1/2-14 NPT 1-7/16" 1/2" 1-3/16" 19/32 1/2-14 NPT 1-7/16" 3/4" 1-29/64" 19/32 3/4-14 NPT 1-9/16" 1" 1-23/32" 21/ /2 NPT 1-11/16" 1-1/4" 2-3/16" 5/8 1-1/4-11-1/2 NPT 2-1/32" 1-1/2" 2-1/2" 5/8 1-1/2-11-1/2 NPT 2-7/32" 2" 3" 21/ /2 NPT 2-9/32" 2-1/2" 3-5/8" 1 2-1/2-8 NPT 3-1/2" 3" 4-5/16" NPT 3-3/4" 3-1/2" 4-13/16" 1 3-1/2-8 NPT 3-3/4" 4" 5-5/16" NPT 3-3/4" C A=Nut Flats B = Thread length and thread spec. C = Overall length

51 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS MALLEABLE IRON 45 DEGREE CONNECTORS B51 Applications For use in outdoor or indoor locations on flexible metallic liquidtight conduit and Type B flexible nonmetallic liquidtight conduit Use to positively bond the conduit to a box or enclosure RACO liquidtight connectors are suitable for use in Class 1, Division 2; Class 2, Division 1 and 2; and Class 3, Division 1 and 2 hazardous locations Patented split gland-ring is designed to slip onto the conduit quickly and to grip the jacket of the conduit, speeding installation, assuring a perfect seal, and preventing pullouts Malleable iron castings mate with other components perfectly without strain or distortion All components are reusable RACO liquidtight connectors may be easily disassembled and reused after years of service Sealing washer (included) provides a liquidtight seal when terminating the connector in a threadless opening Heavy duty locknut included with every RACO liquidtight connector assures continuity of ground All metallic components are zinc electro plated for added corrosion protection Compliances C22.2 #18 45 DEGREE INSULATED MALLEABLE IRON ORDERING INFORMATION - 45 DEGREE - INSULATED AND UNINSULATED- MALLEABLE IRON TRADE SIZE A B THREAD SPEC. 45 DEGREE UNINSULATED MALLEABLE IRON INSULATED UNINSULATED IRON IRON TRADE UNIT SHIP UPC SIZE 3561* 3441* 3/8" /2" /4" " /4" /2" " 5 *1/2" Trade size hub 3/8" 1-1/16" 19/32" 1/2-14 NPT 1-3/16" 1-9/32" 1/2" 1-3/16" 19/32" 1/2-14 NPT 1-3/16" 1-9/32" 3/4" 1-29/64" 19/32" 3/4-14 NPT 1-3/16" 1-7/16" 1" 1-23/32" 21/32" /2 NPT 1-3/8" 1-17/32" 1-1/4" 2-3/16" 5/8" 1-1/4-11-1/2 NPT 1-27/64" 1-11/16" 1-1/2" 2-1/2" 5/8" 1-1/2-11-1/2 NPT 1-21/32" 2" 2" 3" 21/32" /2 NPT 1-11/16" 2-1/4"" A=Nut Flats B = Thread length and thread spec. C = Thread to bend D=Nut to bend C D

52 B52 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS MALLEABLE IRON 90 DEGREE CONNECTORS Applications For use in outdoor or indoor locations on flexible metallic liquidtight conduit and Type B flexible nonmetallic liquidtight conduit Use to positively bond the conduit to a box or enclosure RACO liquidtight connectors are suitable for use in Class 1, Division 2; Class 2, Division 1 and 2; and Class 3, Division 1 and 2 hazardous locations Patented split gland-ring is designed to slip onto the conduit quickly and to grip the jacket of the conduit, speeding installation, assuring a perfect seal, and preventing pullouts Malleable iron castings mate with other components perfectly without strain or distortion All components are reusable RACO liquidtight connectors may be easily disassembled and reused after years of service Sealing washer (included) provides a liquidtight seal when terminating the connector in a threadless opening Heavy duty locknut included with every RACO liquidtight connector assures continuity of ground All metallic components are zinc electro plated for added corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances C22.2 #18 90 DEGREE INSULATED MALLEABLE IRON ORDERING INFORMATION - 90 DEGREE - INSULATED AND UNINSULATED- MALLEABLE IRON TRADE SIZE A B THREAD SPEC. 90 DEGREE UNINSULATED MALLEABLE IRON INSULATED UNINSULATED IRON IRON TRADE UNIT SHIP UPC SIZE 3541* 3421* 3/8" /2" /2" /4" /4" " " /4" /2" " /2" " " 1 *1/2" Trade size hub 3/8" 1-1/16" 19/32" 1/2-14 NPT 1-5/16" 1-7/16" 1/2" 1-3/16" 19/32" 1/2-14 NPT 1-5/16" 1-1/16" 3/4" 1-29/64" 19/32" 3/4-14 NPT 1-7/16" 1-5/8" 1" 1-23/32" 21/32" /2 NPT 1-25/32" 2-3/16" 1-1/4" 2-3/16" 5/8" 1-1/4-11-1/2 NPT 1-31/32" 2-1/2" 1-1/2" 2-1/2" 5/8" 1-1/2-11-1/2 NPT 2-3/16" 2-11/16" 2" 3" 21/32" /2 NPT 2-17/32" 3-1/4" 2-1/2" 3-5/8" 1" 2-1/2-8 NPT 3-3/8" 4-1/4" 3" 4-5/16" 1" 3-8 NPT 3-11/16" 4-7/8" 4" 5-5/16" 1" 4-8 NPT 4-3/16" 5-5/8" C D A=Nut Flats B = Thread length and thread spec. C = Thread to bend D=Nut to bend

53 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS STEEL/MALLEABLE IRON STRAIGHT CONNECTORS GROUNDING TYPE B53 Applications For use in outdoor or indoor locations on flexible metallic liquidtight conduit, when installation of a copper or aluminum external bonding jumper is required RACO grounding liquidtight connectors are suitable for use in Class 1, Division 2; Class 2, Division 1 and 1; and Class 3, Division 1 and 2 hazardous locations Patented split gland-ring is designed to slip onto the conduit quickly and to grip the jacket of the conduit, speeding installation, assuring a perfect seal, and preventing pullouts Screw machined bodies (straight through 1") and precision threaded malleable iron castings mate with other components perfectly without strain or distortion All components are reusable RACO liquidtight connectors may be easily disassembled and reused after years of service Sealing washer (included) provides a liquidtight seal when terminating the connector in a threadless opening Heavy duty locknut included with every RACO liquidtight connector assures continuity of ground All metallic components are zinc electro plated for added corrosion protection Compliances C22.2 #18 STRAIGHT - INSULATED WITH GROUND LUG STEEL/MALLEABLE IRON ORDERING INFORMATION - STRAIGHT - INSULATED WITH GROUND LUG STEEL/MALLEABLE IRON UNIT. SHIP. GROUNDING UPC WIRE CAPACITY CTN. QTY. CTN. QTY. BAR MIN. MAX. CODE * 3/8" 25 #14 SOL. #4 STR /2" 25 #14 SOL. #4 STR /4" 25 #14 SOL. #4 STR " 10 #14 SOL. #4 STR /4" 10 #14 SOL. #4 STR /2" 5 #14 SOL. #4 STR " 5 #14 SOL. #4 STR /2" 1 #14 SOL. #110 STR " 1 #14 SOL. #110 STR /2" 1 #6 STR. #250 MCM " 1 #6 STR. #250 MCM *1/2" Trade size hub TRADE SIZE A B THREAD SPEC. 3/8" 1-3/16" 19/32" 1/2-14 NPT 1-7/16" 25/32" 1/2" 1-5/16" 19/32" 1/2-14 NPT 1-7/16" 25/32" 3/4" 1-9/16" 19/32" 3/4-14 NPT 1-9/16" 25/32" 1" 1-27/32" 21/32" /2 NPT 1-11/16" 25/32" 1-1/4" 2-3/16" 5/8" 1-1/4-11-1/2 NPT 2-1/32" 25/32" 1-1/2" 2-1/2" 5/8" 1-1/2-11-1/2 NPT 2-7/32" 25/32" 2" 3" 2-1/32" /2 NPT 2-9/32" 25/32" 2-1/2" 3-5/8" 1" 2-1/2-8 NPT 3-1/2" 1-11/64" 3" 4-5/16" 1" 3-8 NPT 3-3/4" 1-11/64" 3-1/2" 4-13/16" 1" 3-1/2-8 NPT 3-3/4" 1-57/64" 4" 5-5/16" 1" 4-8 NPT 3-3/4" 1-57/64" C D A= Nut Flats B = Thread length and thread spec. C = Overall length D = Lug height

54 B54 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS STEEL/MALLEABLE IRON 45 DEGREE CONNECTORS GROUNDING TYPE Applications For use in outdoor or indoor locations on flexible metallic liquidtight conduit, when installation of a copper or aluminum external bonding jumper is required RACO grounding liquidtight connectors are suitable for use in Class 1, Division 2; Class 2, Division 1 and 1; and Class 3, Division 1 and 2 hazardous locations Patented split gland-ring is designed to slip onto the conduit quickly and to grip the jacket of the conduit, speeding installation, providing a liquidtight seal, and preventing pullouts Malleable iron castings mate with other components perfectly without strain or distortion All components are reusable RACO liquidtight connectors may be easily disassembled and reused after years of service Sealing washer (included) provides a liquidtight seal when terminating the connector in a threadless opening Heavy duty locknut included with every RACO liquidtight connector assures continuity of ground All metallic components are zinc electro plated for added corrosion protection Compliances C22.2 #18 45 DEGREE - INSULATED WITH GROUND LUG MALLEABLE IRON ORDERING INFORMATION - STRAIGHT - INSULATED WITH GROUND LUG STEEL/MALLEABLE IRON UNIT. SHIP. GROUNDING UPC WIRE CAPACITY CTN. QTY. CTN. QTY. BAR MIN. MAX. CODE * 3/8" 25 #14 SOL. #4 STR /2" 25 #14 SOL. #4 STR /4" 25 #14 SOL. #4 STR " 10 #14 SOL. #4 STR /4" 10 #14 SOL. #4 STR /2" 5 #14 SOL. #4 STR " 5 #14 SOL. #4 STR. *1/2" Trade size hub TRADE SIZE A B THREAD SPEC. C D E 3/8" 1-3/16" 19/32" 1/2-14 NPT 1-3/16" 1-9/32" 25/32" 1/2" 1-5/16" 19/32" 1/2-14 NPT 1-3/16" 1-9/32" 25/32" 3/4" 1-9/16" 19/32" 3/4-14 NPT 1-3/16" 1-7/16" 25/32" 1" 1-27/32" 21/32" /2 NPT 1-3/8" 1-17/32" 25/32" 1-1/4" 2-3/16" 5/8" 1-1/4-11-1/2 NPT 1-27/64" 1-11/16" 25/32" 1-1/2" 2-1/2" 5/8" 1-1/2-11-1/2 NPT 1-21/32" 2" 25/32" 2" 3" 21/32" /2 NPT 1-11/16" 2-1/4" 25/32" A=Nut Flats B = Thread length and thread spec. C = Thread to bend D=Nut to bend E = Lug height

55 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS STEEL/MALLEABLE IRON 90 DEGREE CONNECTORS GROUNDING TYPE B55 Applications For use in outdoor or indoor locations on flexible metallic liquidtight conduit, when installation of a copper or aluminum external bonding jumper is required RACO grounding liquidtight connectors are suitable for use in Class 1, Division 2; Class 2, Division 1 and 1; and Class 3, Division 1 and 2 hazardous locations Patented split gland-ring is designed to slip onto the conduit quickly and to grip the jacket of the conduit, speeding installation, providing a liquidtight seal, and preventing pullouts Malleable iron castings mate with other components perfectly without strain or distortion All components are reusable RACO liquidtight connectors may be easily disassembled and reused after years of service Sealing washer (included) provides a liquidtight seal when terminating the connector in a threadless opening Heavy duty locknut included with every RACO liquidtight connector assures continuity of ground All metallic components are zinc electro plated for added corrosion protection Compliances C22.2 #18 90 DEGREE - INSULATED WITH GROUND LUG MALLEABLE IRON ORDERING INFORMATION - STRAIGHT - INSULATED WITH GROUND LUG STEEL/MALLEABLE IRON UNIT. SHIP. GROUNDING UPC WIRE CAPACITY CTN. QTY. CTN. QTY. BAR MIN. MAX. CODE * 3/8" 25 #14 SOL. #4 STR /2" 25 #14 SOL. #4 STR /4" 25 #14 SOL. #4 STR " 10 #14 SOL. #4 STR /4" 10 #14 SOL. #4 STR /2" 5 #14 SOL. #4 STR " 5 #14 SOL. #4 STR /2" 1 #14 SOL. #4 STR " 1 #14 SOL. #4 STR " 1 #14 SOL. #4 STR. *1/2" Trade size hub TRADE SIZE A B THREAD SPEC. A=Nut Flats B = Thread length and thread spec. C = Thread to bend D=Nut to bend E = Lug height C D E 3/8" 1-3/16" 19/32" 1/2-14 NPT 1 5/16" 1-7/16" 25/32" 1/2" 1-5/16" 19/32" 1/2-14 NPT 1-5/16" 1-7/16" 25/32" 3/4" 1-9/16" 19/32" 3/4-14 NPT 1-7/16" 1-5/8" 25/32" 1" 1-27/32" 21/32" /2 NPT 1-25/32" 2-3/16" 25/32" 1-1/4" 2-3/16" 5/8" 1-1/4-11-1/2 NPT 1-31/32" 2-1/2" 25/32" 1-1/2" 2-1/2" 5/8" 1-1/2-11-1/2 NPT 2-3/16" 2-11/16" 25/32" 2" 3" 21/32" /2 NPT 2-17/32" 3-1/4" 25/32" 2-1/2" 3-5/8" 1" 2-1/2-8 NPT 3-3/8" 4-1/4" 1-11/64" 3" 4-5/16" 1" 3-8 NPT 3-11/16" 4-7/8" 1-11/64" 4" 5-5/16" 1" 4-8 NPT 4-3/16" 5-5/8" 1-57/64"

56 B56 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS STEEL SEALING WASHERS Application For use whenever a positive seal is required between the shoulder of a fitting and an enclosure One-piece construction assures proper installation no need to worry about aligning multiple components Steel ring is zinc electro plated for added corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances C22.2 #18 SEALING WASHERS* ORDERING INFORMATION - SEALING WASHERS* UNIT. SHIP. UPC /2" /2" /4" /4" " " /4" /2" " 5 25 *One-piece steel ring and neoprene gasket, raintight * CONDUIT SIZE A B C 1/2" 1-5/64" 5/64" 51/64" 3/4" 1-11/32" 5/32" 1" 1" 1-5/8" 11/64" 1-1/4" 1-1/4" 2" 11/64" 1-39/64" 1-1/2" 2-23/64" 3/16" 1-27/32" 2" 2-53/64" 3/16" 2-5/16" *Dimensions when ring and gasket are together A=O.D. B=I.D. C=Thickness

57 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS NONMETALLIC TYPE B CONDUIT AND CONNECTORS B57 Applications For use in dry or wet locations when the conduit and fittings are not subject to physical damage Use Type B conduit and fittings whenever flexibility is required for installation, operation, or maintenance All gray nonmetallic construction ends metal fatigue and separation problems Conduit cuts cleanly speeds installation and ends the worry of jagged edges Each connector is supplied with a Neoprene o-ring and nylon locknut UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances Standard 1660 (conduit); Standard 514B (fittings) C22.2 #18 Type B Liquidtight Flexible Nonmetallic Conduit Dimensions TRADE CONDUIT BEND SIZE I.D./O.D. RADIUS 3/8".49/.70" 2.00" 1/2".63/.83" 3.00" 3/4".83/1.04" 4.00" 1" 1.05/1.30" 5.00" 1-1/4" 1.40/1.65" 6.30" 1-1/2" 1.59/1.88" 7.50" 2" 2.03/2.36" 10.00" TYPE B LIQUIDTIGHT FLEXIBLE NONMETALLIC CONDUIT ORDERING INFORMATION - TYPE B LIQUIDTIGHT FLEXIBLE - NONMETALLIC CONDUIT STRAIGHT CONNECTORS - NYLON FOR TYPE B CONDUIT FEET PER UPC. PACKAGE BAR CODE /8" /2" /4" " /4" /2" " 50 STRAIGHT CONNECTORS - NYLON - FOR TYPE B CONDUIT UNIT. SHIP. UPC 4721* 3/8" /2" /2" /4" /4" " " /4" /2" " 5 *1/2" Trade size hub TRADE E SIZE A B C D A/C* A/F** 3/8" 1.14" 1.63".57".42" 1.41" 1.30" 1/2" 1.30" 2.14".57".55" 1.41" 1.30" 3/4" 1.53" 2.22".58".74" 1.85" 1.53" 1" 1.80" 2.32".72".96" 1.94" 1.80" 1-1/4" 2.20" 2.15".74" 1.30" 2.38" 2.18" 1-1/2" 2.49" 2.35".76" 1.46" 2.63" 2.43" 2" 3.05" 2.51".79" 1.90" 3.13" 2.93" * A/C=Across corners **A/F=Across flats

58 B58 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS NONMETALLIC SWIVEL LOK CONNECTORS FOR TYPE B NONMETALLIC CONDUIT Swivel Lok and 90 Degree Connectors Applications For use in dry or wet locations when the conduit and fittings are not subject to physical damage Use Type B conduit and fittings whenever flexibility is required for installation, operation, or maintenance Swivel Lok and 90 Degree Connectors All gray nonmetallic construction provides superior corrosion resistance Each connector is supplied with a Neoprene O-ring and nylon gasket Swivel Lok Connectors Swivel Lok multi-position connector (trade sizes 3/8" to 1") twists from 0 to 90, easing installation in difficult locations and eliminating need to stock other angle connectors UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Swivel Lok and 90 Degree Connectors Compliances C22.2 #18 SWIVEL LOK MULTI - POSITION CONNECTORS NYLON - FOR TYPE B CONDUIT ORDERING INFORMATION - SWIVEL LOK MULTI - POSITION CONNECTORS - NYLON FOR TYPE B CONDUIT UNIT. SHIP. UPC 4731* 3/8" /2" /2" /4" /4" " " 1 10 *1/2" Trade size hub TRADE SIZE F G A/C* H A/F** I J K 3/8" 3.27".57" 1.41" 1.30" 1.30" 1.43" 2.00" 1/2" 3.27".57" 1.41" 1.30" 1.30" 1.43" 2.00" 3/4" 3.66".58" 1.65" 1.53" 1.53" 1.59" 2.23" 1" 4.00".72" 1.94" 1.80" 1.80" 1.84" 2.30" * A/C=Across corners ** A/F=Across flats 90 DEGREE CONNECTORS NYLON TYPE B CONDUIT 90 DEGREE CONNECTORS - NYLON - TYPE B CONDUIT UNIT. SHIP. UPC /4" 10 TRADE E SIZE A B C D A/C* A/F** 1-1/4" 2.21" 3.57".74" 1.30" 2.38" 2.18" * A/C=Across corners ** A/F=Across flats

59 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS NONMETALLIC EXTRA FLEXIBLE TUBING AND CONNECTORS B59 Applications For use in dry or wet locations when the conduit and fittings are not subject to physical damage Use extra flexible tubing and connectors whenever added flexibility is required for installation, operation, or maintenance All black nonmetallic construction ends metal fatigue and separation problems Conduit cuts cleanly - speeds installation and ends the worry of jagged edges Each connector is supplied with a Neoprene O-ring and nylon gasket Compliances Recognized (tubing) C22.2 #18 (tubing & fitting) (fitting) Extra Flexible Liquidtight Nonmetallic Tubing Dimensions TRADE CONDUIT BEND SIZE I.D./O.D. RADIUS 3/8".49/.70" 2.00" 1/2".63/.83" 3.00" 3/4".83/1.04" 4.00" 1" 1.05/1.30" 5.00" 1-1/4" 1.40/1.65" 6.30" 1-1/2" 1.59/1.88" 7.50" 2" 2.03/2.36" 10.00" EXTRA FLEXIBLE LIQUIDTIGHT NONMETALLIC TUBING ORDERING INFORMATION - STRAIGHT CONNECTORS NYLON FOR EXTRA FLEXIBLE TUBING EXTRA FLEXIBLE LIQUIDTIGHT - NONMETALLIC TUBING FEET PER UPC PACKAGE BAR CODE /8" /2" /4" " /4" /2" " 50 STRAIGHT CONNECTORS - NYLON - FOR EXTRA FLEXIBLE TUBING UNIT. SHIP. UPC 4741* 3/8" /2" /4" " /4" /2" " 5 *1/2" Trade size hub STRAIGHT CONNECTORS - NYLON - FOR EXTRA FLEXIBLE TUBING TRADE SIZE A B C D 3/8" 1.14" 1.63".57".42" 1.41" 1.30" 1/2" 1.30" 2.14".57".55" 1.41" 1.30" 3/4" 1.53" 2.22".58".74" 1.85" 1.53" 1" 1.80" 2.32".72".96" 1.94" 1.80" 1-1/4" 2.20" 2.15".74" 1.30" 2.38" 2.18" A/C* E A/F** 1-1/2" 2.49" 2.35".76" 1.46" 2.63" 2.43" 2" 3.05" 2.51".79" 1.90" 3.13" 2.93" * A/C=Across corners ** A/F=Across flats

60 B60 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS NONMETALLIC SWIVEL LOK CONNECTORS FOR EXTRA FLEXIBLE TUBING Applications For use in dry or wet locations when the conduit and fittings are not subject to physical damage Use extra flexible tubing and connectors whenever added flexibility is required for installation, operation, or maintenance All black nonmetallic construction ends metal fatigue and separation problems Swivel Lok multi-position connector (trade sizes 3/8" to 1") twists from 0 to 90, easing installation in difficult locations and eliminating need to stock other angle connectors Compliances C22.2 #18 SWIVEL LOK MULTI - POSITION CONNECTORS NYLON FOR EXTRA FLEXIBLE TUBING ORDERING INFORMATION - SWIVEL LOK MULTI - POSITION CONNECTORS - NYLON FOR EXTRA FLEXIBLE TUBING UNIT. SHIP. UPC 4751* 3/8" /2" /4" " 10 *1/2" Trade size hub TRADE C SIZE A B A/C* A/F** D E F 3/8" 3.27".57" 1.41" 1.30" 1.30" 1.43" 2.00" 1/2" 3.27".57" 1.41" 1.30" 1.30" 1.43" 2.00" 3/4" 3.66".58" 1.65" 1.53" 1.53" 1.59" 2.23" 1" 4.00".72" 1.94" 1.80" 1.80" 1.84" 2.30" * A/C=Across corners ** A/F=Across flats

61 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS NONMETALLIC 90 DEGREE CONNECTOR FOR EXTRA FLEXIBLE TUBING AND CONDUIT CONNECTOR KIT WITH SWIVEL-LOK MULTI-POSITION CONNECTOR B61 90 Degree Connector and Conduit and Conductor Kit Application For use in wet or dry locations when the conduit and fittings are not subject to physical damage 90 Degree Connector Application Use extra flexible tubing and connectors whenever added flexibility is required for installation, operation or maintenance Conduit and Connector Kit Application Use RACO conduit and connector kits whenever flexibility is required for installation, operation, or maintenance 90 Degree Connector All black nonmetallic construction provides corrosion protection Each connector is supplied with a Neoprene o-ring and nylon gasket Conduit and Connector Kit All gray nonmetallic construction ends metal fatigue and separation problems Each kit contains all components necessary for installation no need to worry about mismatched components Convenient to use RACO conduit and connector kits are ideal for air conditioners, swimming pools, lighting, hot tub and heat pump installation UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation 90 Degree Connector Compliances C22.2 #18 Conduit and Connector Kit Compliances Standard 1660 (conduit); Standard 514B (fittings) C22.2 #18 90 DEGREE CONNECTORS NYLON FOR EXTRA FLEXIBLE TUBING ORDERING INFORMATION - 90 DEGREE CONNECTORS - NYLON FOR EXTRA FLEXIBLE TUBING UNIT. SHIP. UPC /4" 10 TRADE E SIZE A B C D A/C* A/F** 1-1/4" 2.21" 3.57".74" 1.30" 2.38" 2.18" * A/C=Across corners ** A/F=Across flats CONDUIT AND CONNECTOR KIT* CONDUIT AND CONNECTOR KIT* UNIT. SHIP. UPC /2" /4" 1 5 *Kit contains 6 foot length of Type B conduit, one straight and one Swivel Lok connector

62 B62 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS STEEL/MALLEABLE IRON STRAIN RELIEF CORD CONNECTORS Applications For use in wet or dry locations to provide a liquidtight and strain relief termination for flexible cord and cable RACO liquidtight strain relief cord connectors are suitable for use in Class 1, Division 2; Class 2, Division 1and 2; and Class 3, Division 1 and 2 hazardous locations All steel/malleable construction provides mechanical strength Screw machined bodies (straights through 1") and precision threaded malleable iron castings mate with other components without strain or distortion Unique Neoprene grommet design grommet is forced up and around the cord when the nut is tightened for a positive liquidtight seal Washers have size range imprinted for identification eliminates misidentifying inventory Use RACO locknuts and sealing washers to complete a liquidtight installation on a sheet metal box or panel All metallic components are zinc electro plated for corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliance STRAIGHT CONNECTORS STEEL - MALLEABLE IRON ORDERING INFORMATION - STRAIGHT CONNECTORS - STEEL - MALLEABLE IRON UNIT SHIP UPC CABLE RANGE 1/2" HUBS FORM /2" HUBS FORM /4" HUBS FORM " HUBS FORM /4" HUBS FORM /2" HUBS FORM A=Nut Flats B = Thread length and thread spec. C = Overall length HUB FORM THREAD SIZE SIZE A SPEC. B C 1/2" F1 1-1/16" 1/2-14 NPT 19/32" 1-7/16" 1/2" F2 1-3/16" 1/2-14 NPT 19/32" 1-7/16" 3/4" F3 1-29/64" 3/4-14 NPT 19/32" 1-9/16" 1" F4 1-23/32" /2 NPT 21/32" 1-11/16" 1-1/4" F5 2-3/16" 1-1/4-11-1/2 NPT 5/8" 2-1/32" 1-1/2" F6 2-1/2" 1-1/2-11-1/2 NPT 5/8" 2-7/32"

63 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS MALLEABLE IRON 90 DEGREE STRAIN RELIEF CORD CONNECTORS B63 Applications For use in wet or dry locations to provide a liquidtight and strain relief termination for flexible cord and cable RACO liquidtight strain relief cord connectors are suitable for use in Class 1, Division 2; Class 2, Division 1and 2; and Class 3, Division 1 and 2 hazardous locations All steel/malleable construction provides mechanical strength Malleable iron castings mate with other components without strain or distortion Unique Neoprene grommet design grommet is forced up and around the cord when the nut is tightened for a positive liquidtight seal Washers have size range imprinted for identification eliminates misidentifying inventory Use RACO locknuts and sealing washers to complete a liquidtight installation on a sheet metal box or panel All metallic components are zinc electro plated for corrosion protection Compliance 90 DEGREE CONNECTORS MALLEABLE IRON ORDERING INFORMATION - 90 DEGREE CONNECTORS - MALLEABLE IRON CABLE SHIP UPC RANGE CTN. QTY. BAR CODE 1/2" HUBS FORM /2" HUBS FORM /4" HUBS FORM HUB FORM THREAD SIZE SIZE A SPEC. B C D 1/2" F1 1-1/16" 1/2-14 NPT 19/32" 1-5/16" 1-7/16" 1/2" F2 1-3/16" 1/2-14 NPT 19/32" 1-5/16" 1-7/16" 3/4" F3 1-29/64" 3/4-14 NPT 19/32" 1-7/16" 1-5/8" A = Nut Flats B = Thread length and thread spec. C = Thread to bend D=Nut to bend

64 B64 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS NONMETALLIC STRAIN RELIEF CORD CONNECTORS Applications For use in wet or dry locations to provide a liquidtight and strain relief termination for flexible cord and cable Nonmetallic liquidtight strain relief cord connectors are suitable for use in Class 1, Division 2; Class 2, Divisions 1 and 2; and Class 3, Divisions 1 and 2 hazardous locations Nylon construction is lightweight and easy to use Neoprene grommet Resists most common industrial corrosives Color-coded Gotcha ring provides fast identification of cord size DIAMETER RANGE Compliances C22.2 #18 COLOR CODE Green Orange Red Black White White Blue Blue Brown Yellow Purple Grey Pink STRAIGHT CONNECTORS - NYLON STRAIGHT CONNECTORS NYLON ORDERING INFORMATION - CABLE SHIP UPC. RANGE CTN. QTY. BAR CODE 1/4" HUBS FORM /8" HUBS FORM /2" HUBS FORM /4" HUBS FORM " HUBS FORM A = Nut O.D. B = Thread length C = Length to shoulder D=Throat I.D. HUB FORM SIZE SIZE A B C D 1/4" F1 63/64" 7/16" 1-3/32" 21/64" 3/8" F1 63/64" 7/16" 1-3/32" 7/16" 1/2" F2 1-1/4" 17/32" 1-1/2" 37/64" 3/4" F3 1-31/64" 35/64" 1-5/8" 49/64" 1" F4 1-27/32" 11/16" 1-3/4" 1-1/64"

65 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS NONMETALLIC 90 DEGREE STRAIN RELIEF CORD CONNECTORS B65 Applications For use in wet or dry locations to provide a liquidtight and strain relief termination for flexible cord and cable Nonmetallic liquidtight strain relief cord connectors are suitable for use in Class 1, Division 2; Class 2, Divisions 1 and 2; and Class 3, Divisions 1and 2 hazardous locations Nylon construction is lightweight and easy to use Neoprene grommet Resists most common industrial corrosives Color-coded Gotcha ring provides fast identification of cord size DIAMETER RANGE Red Compliances C22.2 #18 COLOR CODE White Blue Brown Yellow Purple Grey 90 DEGREE CONNECTORS NYLON ORDERING INFORMATION - 90 DEGREE CONNECTORS - NYLON CABLE SHIP UPC RANGE CTN. QTY. BAR CODE 1/2" HUBS FORM /4" HUBS FORM " HUBS FORM HUB SIZE FORM SIZE A B C D E 1/2" F2 1-1/4" 17/32" 37/64" 2-1/2" 1-13/32" 3/4" F3 1-31/64" 35/64" 49/64" 2-51/64" 1-21/32" 1" F4 1-27/32" 11/16" 1-1/64" 3-19/64" 1-63/64" A = Nut O.D. B = Thread length C=Throat I.D. D = Overall length E = Height from shoulder to nut

66 B66 LIQUIDTIGHT CONDUIT AND CORD CONNECTORS ALUMINUM STRAIGHT STRAIN RELIEF CORD CONNECTORS Applications For use in wet or dry locations to provide a liquidtight and strain relief termination for flexible cord and cable Aluminum liquidtight strain relief cord connectors are suitable for use in Class 1, Division 2; Class 2, Divisions 1 and 2; and Class 3, Divisions 1 and 2 hazardous locations Aluminum construction provides a corrosion-resistant installation Patented Gotcha ring incorporates a split hinge design to prevent friction and to provide strain relief Neoprene grommet Knurled compression nut allows the fittings to be hand tightened to UL requirements Gotcha ring is color-coded for sizing identification DIAMETER RANGE Compliances C22.2 #18 COLOR CODE Green Orange Red Black White White Blue Blue Brown Yellow Purple Grey Pink STRAIGHT CONNECTORS - ALUMINUM STRAIGHT CONNECTORS ALUMINUM ORDERING INFORMATION - CABLE SHIP UPC RANGE CTN. QTY. BAR CODE 1/2" HUBS FORM /2" HUBS FORM /2" HUBS FORM /4" HUBS FORM /4" HUBS FORM " HUBS FORM A = Nut O.D. B = Thread length C = Length to shoulder D=Throat I.D. E=Hex HUB SIZE FORM A B E C D SIZE DIA. REF. A/C* A/F** 1/2" F1.88".46".90".44" 1.00".88" 1/2" F2 1.13".55" 1.10".64" 1.11" 1.00" 1/2" F3 1.38".55" 1.50".64" 1.40" 1.25" 3/4" F2 1.13".55" 1.10".64" 1.29" 1.13" 3/4" F3 1.38".55" 1.50".82" 1.40" 1.25" 1" F4 1.75".71" 1.60" 1.02" 1.81" 1.62" * A/C=Across corners **A/F=Across flats

67 FLEXIBLE METAL CONDUIT MALLEABLE IRON STRAIGHT SQUEEZE CONNECTORS B67 Application For use in dry locations to bond flexible metal conduit to a box or enclosure All malleable construction insures mechanical protection for the raceway Electro zinc plated for added corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances COMING SOON STRAIGHT - SQUEEZE INSULATED MALLEABLE IRON ORDERING INFORMATION - STRAIGHT - SQUEEZE - INSULATED - MALLEABLE IRON UNIT. SHIP. UPC /8"* /2" /2" /4" /4" " " /4" /2" " /2" " /2" " 1 *For 1/2" knockout B = Thread length and thread spec C = Throat I.D. D = Length to conduit stop E = Clamping range F = Maximum width body TRADE SIZE A B THD. SPEC. C D E F /32" 1/2" 1/2 14 NPS.622" 1/2" 17/32"-5/8" 1-7/32" /8" 3/8" 1/2 14 NPS.622" 7/8" 13/16"-15/16" 1-17/32" /8" 3/8" 1/2 14 NPS.622" 7/8" 13/16"-15/16" 1-17/32" /2" 7/16" 3/4 14 NPS.813" 15/16" 1-1/32"-1-1/8" 1-3/4" /2" 7/16" 3/4 14 NPS.813" 15/16" 1-1/32"-1-1/8" 1-3/4" /4" 5/8" /2 NPT 1.00" 15/16" 1-3/16"-1-3/8" 2" /4" 5/8" /2 NPT 1.00" 15/16" 1-3/16"-1-3/8" 2" /32" 5/8" 1 1/4 11 1/2 NPT 1.250" 1-1/4" 1-15/32"-1-21/32" 2-1/2" /32" 21/32" 1 1/2 11 1/2 NPT 1.500" 1-3/8" 1-25/32"-1-31/32" 2-7/8" /32" 11/16" /2 NPT 2.00" 1-7/8" 2-1/4"-2-15/32" 3-3/8"

68 B68 FLEXIBLE METAL CONDUIT MALLEABLE IRON STRAIGHT SQUEEZE CONNECTORS Application For use in dry locations to bond flexible metal conduit to a box or enclosure All malleable construction insures mechanical protection for the raceway Electro zinc plated for added corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances C22.2 #18 COMING SOON SQUEEZE - STRAIGHT UNINSULATED MALLEABLE IRON ORDERING INFORMATION - SQUEEZE - STRAIGHT - UNINSULATED - MALLEABLE IRON UNIT. SHIP. UPC /8" * /2" /2" /4" /4" " " /4" /2" " /2" " /2" " 1 *For 1/2" knockout B = Thread length and thread spec C = Throat I.D. D = Length to conduit stop E = Clamping range F = Maximum width body TRADE SIZE A B THD. SPEC. C D E F /16" 1/2" 1/2 14 NPS.622" 1/2" 17/32"-5/8" 1-7/32" /32" 3/8" 1/2 14 NPS.622" 7/8" 13/16"-15/16" 1-7/32" /32" 7/16" 3/4 14 NPS.813" 15/16" 1-1/32"-1-1/8" 1-3/4" /32" 5/8" /2 NPT 1.00" 15/16" 1-3/16"-13/8" 2" " 5/8" 1-1/4 11 1/2 NPT 1.250" 1-1/4" 1-15/32"-1-21/32" 2-1/2" /16" 21/32" 1-1/2 11 1/2 NPT 1.500" 1-3/8" 1-25/32"-1-31/32" 2-7/8" /4" 11/16" /2 NPT 2.000" 1-7/8" 2-1/4"-2-15/32" 3-3/8" /64" 57/64" 2-1/2 8 NPS 2.50" 1-3/4" 2-1/2"-3-1/16" 4-1/8" /32" 29/32" 3 8 NPS 3.00" 1-15/16" 3-3/16"-3-9/16" 4-7/8"

69 FLEXIBLE METAL CONDUIT MALLEABLE IRON 90 DEGREE SQUEEZE CONNECTORS B69 Application For use in dry locations to bond flexible metal conduit to a box or enclosure Malleable construction insures mechanical protection for the raceway Electro zinc plated for added corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Insulated Compliances C22.2 #18 ( ) Uninsulated Compliances C22.2 #18 ( ) CS CS CS CS SQUEEZE 90 DEGREE - INSULATED MALLEABLE IRON ORDERING INFORMATION - SQUEEZE 90 DEGREE - UNINSULATED MALLEABLE IRON SQUEEZE 90 DEGREE INSULATED AND UNINSULATED MALLEABLE IRON INSULATED UNINSULATED IRON IRON TRADE UNIT SHIP UPC SIZE /8" * /2" /2" /2" /4" /4" " " /4" /2" " /2" " /2" " 1 CS CS Coming Soon * For 1/2" knockout CS B = Thread length and thread spec C = Throat I.D. D = Length to conduit stop E = Clamping range F = Maximum width body INSULATED UNINSULATED IRON IRON THD. A B SPEC. C D E F /16" 1/2 14 NPT.622" 3/4" 7/16"-5/8" 1-3/8" /16" 1/2 14 NPT.622" 7/8" 23/32"-15/16" 2" /16" 1/2 14 NPT.622" 7/8" 23/32"-15/16" 2" /8" 1/2" 3/4 14 NPS.822" 1" 7/8"-1-1/8" 2-3/16" /8" 1/2" 3/4 14 NPS.822" 1" 7/8"-1-1/8" 2-3/16" /8" 5/8" /2 NPT 1.045" 1" 1-7/32"-1-3/8" 2-3/8" /8" 5/8" /2 NPT 1.045" 1" 1-7/32"-1-3/8" 2-3/8" /8" 5/8" 1-1/4 11-1/2 NPT 1.375" 1-1/16" 1-7/16"-1-5/8" 2-3/4" /16" 5/8" 1-1/2 1-21/32" " 1-5/8" 11-1/2 NPT 1-31/32" 3-1/8" /2" 21/32" /2 NPT 2.065" 1-7/8" 2-1/8"-2-15/32" 3-5/8" /8" 15/16" 2-1/2 8 NPS 2.500" 2-1/4" 2-13/16"-31/16" 4-3/8" /16" 1-1/ NPS 3.050" 2-1/2" 3-1/16"-3-9/16" 5"

70 B70 FLEXIBLE METAL CONDUIT DIE CAST ZINC STRAIGHT SQUEEZE CONNECTORS Application For use in dry locations to bond flexible metal conduit to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliance STRAIGHT SQUEEZE UNINSULATED DIE CAST ZINC ORDERING INFORMATION - B = Thread length and thread spec C = Throat I.D. D = Length to conduit stop E = Clamping range F = Maximum width body STRAIGHT SQUEEZE - UNINSULATED - DIE CAST ZINC UNIT. SHIP. UPC /8" * /2" /4" " /4" /2" " * For 1/2" knockout B A B THD. SPEC. C D E F /16" 13/32" 1/ /32" 13/32" 17/32"-21/32" 1-1/16" /16" 13/32" 1/2 14 5/8" 1/2" 27/32"-31/32" 1-3/8" /16" 7/16" 3/ /16" 21/32" 31/32"-1-5/32" 1-19/32" /4" 9/16" /2 1-1/32" 9/16" 1-3/16"-1-7/16" 1-27/32" " 5/8" 1-1/4 11-1/2 1-5/16" 1-3/16" 1-15/32"-1-11/16" 2-1/8" /16" 11/16" 1-1/2 11-1/2 1-19/32" 1-5/16" 1-3/4"-2" 2-3/8" /16" 5/8" /2 2" 1-9/16" 2-5/32"-2-1/2" 2-15/16"

71 FLEXIBLE METAL CONDUIT DIE CAST ZINC 45 AND 90 DEGREE SQUEEZE CONNECTORS B71 Application For use in dry locations to bond flexible metal conduit to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliances C22.2 #18 (2221 not UL Listed or CSA Certified) 45 DEGREE SQUEEZE UNINSULATED DIE CAST ZINC 90 DEGREE SQUEEZE UNINSULATED DIE CAST ZINC ORDERING INFORMATION - 45 DEGREE SQUEEZE - UNINSULATED - MALLEABLE IRON - DIE CAST ZINC UNIT. SHIP. UPC 2221* 3/8" ** /2" 25 A = Length to end of fitting B = Length to bend C = Thread length and thread spec D = Clamping range E = Maximum width body B = Thread length and thread spec C = Throat I.D. D = Length to conduit stop E = Clamping range F = Maximum width body * Not UL Listed or CSA Certified ** For 1/2" knockout A B C THD. SPEC. D E /8" 1-3/16" 1/2" 1/2 14 7/16"-5/8" 1-3/8" /16" 2" 1/2" 1/ /32"-29/32" 1-3/8" 90 DEGREE SQUEEZE - UNINSULATED - DIE CAST ZINC UNIT. SHIP. UPC /8" * /2" /4" " /4" /2" " 5 * For 1/2" knockout A B THD. SPEC. C D E F /8" 3/8" 1/ /32" 13/16" 13/32"-9/16" 1-5/16" /32" 11/32" 1/2 14 5/8" 1-1/32" 21/32"-15/16" 1-21/32" /16" 15/32" 3/ /32" 1-1/8" 25/32"-1-1/8" 1-29/32" /16" 9/16" /2 1-1/32" 1" 1-3/32"-1-1/2" 2-3/8" " 5/8" 1-1/4 11-1/2 1-3/8" 1-1/8" 1-5/16"-1-3/4" 2-11/16" /4" 3/4" 1-1/2 11-1/2 1-7/16" 1-13/16" 1-9/16"-2-1/4" 3-5/8" /4" 3/4" /2 1-31/32" 1-13/16" 1-19/32"-2-1/4" 3-9/16"

72 B72 FLEXIBLE METAL CONDUIT DIE CAST ZINC SCREW-IN TYPE CONNECTORS AND COUPLINGS Application For use in dry locations to bond flexible metal conduit to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliance CONNECTORS SCREW-IN UNINSULATED DIE CAST ZINC COUPLINGS SCREW-IN DIE CAST ZINC ORDERING INFORMATION - CONNECTORS SCREW-IN UNINSULATED DIE CAST ZINC UNIT. SHIP. UPC /8" * /2" /4" *1/2" Trade size hub B = Thread length and thread spec C = Throat I.D. D = Length to conduit stop A B THD. SPEC. C D /64" 7/16" 1/2 14 9/16" 23/32" /8" 3/8" 1/2 14 5/8" 25/32" /32" 1/2" 3/ /16" 31/32" COUPLINGS SCREW-IN DIE CAST ZINC UNIT. SHIP. UPC /2" /4" A B C /64" 9/16" 13/16" /64" 3/4" 1" B = Throat I.D. C = Length to center stop

73 FLEXIBLE METAL CONDUIT DIE CAST ZINC SET SCREW CONNECTORS B73 Application For use in dry locations to bond flexible metal conduit to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliance SET SCREW CONNECTOR DIE CAST ZINC SET SCREW CONNECTOR DIE CAST ZINC ORDERING INFORMATION - SET SCREW CONNECTOR - DIE CAST ZINC UNIT. SHIP. UPC /2" B = Thread length C = Throat I.D. D = Length to conduit stop E = Screw spec F = Body O.D. G = Body I.D. A B THD. SPEC. C D E F G /64" 3/8" 1/2-14 5/8" 1-1/32" 8-32x1/2" 1-5/32" 15/16" SET SCREW CONNECTOR - DIE CAST ZINC UNIT. SHIP. UPC /8" * A B C D /8" 7/16" 3/8" x 1/2" * For 1/2" knockout B = Thread length C = Throat I.D. D = Screw spec

74 B74 FLEXIBLE METAL CONDUIT DIE CAST ZINC CLAMP TYPE CONNECTORS AND DUPLEX CONNECTORS Application For use in dry locations to bond flexible metal conduit to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliance CLAMP TYPE DIE CAST ZINC DUPLEX DIE CAST ZINC ORDERING INFORMATION - CLAMP TYPE - DIE CAST ZINC UNIT. SHIP. UPC /8"* * For 1/2" knockout B = Thread length C = Throat I.D. D = Clamping range E = Maximum body width THD. A B SPEC. C D E /32" 3/8" 1/2-14 3/8" 5/32"-5/8" 1-3/16" DUPLEX - DIE CAST ZINC UNIT. SHIP. UPC /8"* * For 1/2" knockout A B C D /16" 1-21/32" 7/16" 1/8"-9/16" B = Width C = Thread length D = Clamping range

75 FLEXIBLE METAL CONDUIT MALLEABLE IRON COMBINATION COUPLINGS B75 Applications For use when coupling flexible metal conduit to rigid/imc conduit Use RACO Cat. Nos when coupling threaded rigid/imc conduit to flexible metal conduit Rugged metallic construction insures mechanical protection Steel/malleable components are electro zinc plated for added corrosion protection Compliance FLEX - RIGID COUPLINGS MALLEABLE IRON ORDERING INFORMATION - FLEX - RIGID COUPLINGS - MALLEABLE IRON UNIT. SHIP. UPC /2" /4" " 25 D A B C THD. SPEC. E /8" 1-1/32" 3/4" 1/2-14 NPT 1-21/32" /8" 1-7/32" 31/32" 3/4-14 NPT 1-25/32" /16" 1-1/2" 1-7/32" /2 NPT 1-13/16" A = Width across flex side B= Hub O.D. C = Hub I.D. D = Thread spec hub E = Overall length

76 B76 FLEXIBLE METAL CONDUIT MALLEABLE IRON COMBINATION COUPLINGS Applications For use when coupling flexible metal conduit to EMT Conduit Use RACO Cat. Nos when coupling flexible metal conduit to EMT conduit Rugged metallic construction insures mechanical protection Steel/malleable components are electro zinc plated for added corrosion protection UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances Certified for Canada FLEX - EMT COUPLINGS SQUEEZE - MALLEABLE IRON ORDERING INFORMATION - FLEX - EMT COUPLINGS SQUEEZE - MALLEABLE IRON FLEX EMT UNIT SHIP UPC SIZE SIZE 1941* 3/8" 1/2" /2" 1/2" /2" 1/2" /4" 3/4" /4" 3/4" 1 20 A = Width across flex side B = Overall length C = Nut O.D. D = Nut I.D. E = Clamping range (flex side) *Not U.L. Listed A B C D E /4" 1-5/16" 1-7/64" 23/32" 17/32-5/8" /2" 1-3/4" 1-7/64" 23/32" 13/16-15/16" /2" 1-3/4" 1-7/64" 23/32" 13/16-15/16" /4" 1-53/64" 1-3/8" 15/16" 1-1/32-1-1/8" /4" 1-53/64" 1-3/8" 15/16" 1-1/32-1-1/8"

77 FLEXIBLE METAL CONDUIT DIE CAST ZINC/STEEL COMBINATION COUPLINGS AND NAIL-UP STRAPS B77 Combination Couplings Applications For use when coupling flexible metal conduit to EMT conduit Use RACO Cat. Nos when coupling flexible metal conduit to EMT conduit Combination Couplings Product Feature Rugged metallic construction insures mechanical protection Compliances Certified for Canada Nail-Up Straps Application For use in mounting flexible metal conduit, armored cable, and MC cable Nail-Up Straps Product Feature Stamped steel straps are pregalvanized for added corrosion protection FLEX-EMT COUPLINGS SCREW-IN/COMPRESSION DIE CAST ZINC ORDERING INFORMATION - FLEX-EMT COUPLINGS SCREW-IN/COMPRESSION - DIE CAST ZINC NAIL-UP STRAPS STEEL FLEX EMT UNIT SHIP UPC SIZE SIZE /2" 1/2" /4" 3/4" " 1" NAIL-UP STRAPS - STEEL A " 1.10" " 1.30" " 1.62" UNIT. SHIP. UPC 2252* 3/8" * * 1/2" ** B *For 3/8" flexible metal conduit. Also suitable for AC and MC cable **For 1/2" flexible metal conduit. Also suitable for AC and MC cable A = Width of strap B = Height of strap A /16" 2-3/16" /4" 2-19/64" B

78 B78 ARMORED CABLE CONNECTORS MALLEABLE IRON/ZINC DIE CAST CONNECTORS Application For use in dry locations to bond armored cable to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliance SET SCREW MALLEABLE IRON SET SCREW DIE CAST ZINC ORDERING INFORMATION - SET SCREW - MALLEABLE IRON UNIT SHIP UPC /2" Hub size suitable for use with steel armored cable 14-2 (.450) to 10-2 B = Thread length C = Throat I.D. D = Screw spec A B C D /16" 19/32" 11/32" Fillister Head x 1/2" SET SCREW - DIE CAST ZINC UNIT SHIP UPC /2" Hub size suitable for use with steel armored cable sizes 2#14, 3#14, 2#12, 3#12, 2#10, and 3#10 all with ground wire A B C D /8" 7/16" 3/8" x 1/2" B = Thread length C = Throat I.D. D = Screw spec

79 ARMORED CABLE CONNECTORS ZINC DIE CAST CONNECTORS B79 Application For use in dry locations to bond armored cable to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliance 45 DEGREE SQUEEZE UNINSULATED DIE CAST ZINC CLAMP TYPE DIE CAST ZINC SQUEEZE TYPE UNINSULATED DIE CAST ZINC ORDERING INFORMATION - CLAMP TYPE - DIE CAST ZINC UNIT. SHIP. UPC For 1/2" knockout. Suitable for use with steel armored cable sizes 2#14, 3#14, 2#12, 3#12, 2#10, and 3#10 all with ground wire B = Thread length C = Throat I.D. D = Clamping range E = Maximum body width B = Thread length and thread spec C = Throat I.D. D = Length to conduit stop E = Clamping range F = Maximum width body THD. A B SPEC. C D E /32" 3/8" 1/2-14 3/8" 5/32"-5/8" 1-3/16" SQUEEZE TYPE - UNINSULATED - DIE CAST ZINC UNIT. SHIP. UPC /8"* /2" /4" " * For 1/2" knockout. Suitable for steel armored cable and flexible metal conduit A B THD. SPEC. C D E F /16" 13/32" 1/ /32" 13/32" 17/32"-21/32" 1-1/16" /16" 13/32" 1/2 14 5/8" 1/2" 27/32"-31/32" 1-3/8" /16" 7/16" 3/ /16" 21/32" 31/32"-15/32" 1-19/32" /4" 9/16" /2 1-1/32" 9/16" 1-3/16"-1-7/16" 1-27/32" 45 DEGREE SQUEEZE - UNINSULATED - DIE CAST ZINC UNIT. SHIP. UPC /2" 25 A = Length to end of fitting B = Length to bend C = Thread length and thread spec D = Clamping range E = Maximum width body THD. A B SPEC. C D E /16" 2" 1/2" 1/ /32"-29/32" 1-3/8"

80 B80 ARMORED CABLE CONNECTORS MALLEABLE IRON 90 DEGREE CONNECTORS Application For use in dry locations to bond armored cable to a box or enclosure Rugged metallic construction insures mechanical protection for the raceway UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliance 90 DEGREE SQUEEZE INSULATED THROAT MALLEABLE IRON ORDERING INFORMATION - 90 DEGREE SQUEEZE UNINSULATED MALLEABLE IRON B = Thread length and thread spec C=Throat I.D. D = Length to conduit stop E = Clamping range F = Maximum width body 90 DEGREE SQUEEZE - INSULATED THROAT - MALLEABLE IRON UNIT. SHIP. UPC /8" * /2" /2" /4" /4" 1 20 * For 1/2" knockout 90 DEGREE SQUEEZE - UNINSULATED - MALLEABLE IRON UNIT. SHIP. UPC /8" * /2" /2" /4" /4" 1 20 * For 1/2" knockout A B THD. SPEC. C D E F 3201, /16" 1/2 14 NPT.622" 3/4" 7/16"-5/8" 1-3/8" 3202, /16" 1/2 14 NPT.622" 7/8" 23/32"-15/16" 2" , /16" 1/2 14 NPT.622" 7/8" 23/32"-15/16" 2" 3203, /8" 1/2" 3/4 14 NPS.822" 1" 7/8"-1-1/8" 2-3/16" , /8" 1/2" 3/4 14 NPS.822" 1" 7/8"-1-1/8" 2-3/16"

81 ARMORED CABLE CONNECTORS DIE CAST ZINC 90 DEGREE AND DUPLEX CONNECTORS B81 Application For use in dry locations to bond armored cable to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliance 90 DEGREE SQUEEZE UNINSULATED DIE CAST ZINC DUPLEX DIE CAST ZINC ORDERING INFORMATION - B = Thread length and thread spec C=Throat I.D. D = Length to conduit stop E = Clamping range F = Maximum width body 90 DEGREE SQUEEZE - UNINSULATED - DIE CAST ZINC UNIT. SHIP. UPC /8"* /2" /4" * For 1/2" knockout B A B THD. SPEC. C D E F /8" 3/8" 1/ /32" 13/16" 13/32"-9/16" 1-5/16" /32" 11/32" 1/2 14 5/8" 1-1/32" 21/32"-15/16" 1-21/32" /16" 15/32" 3/ /32" 1-1/8" 25/32"-1-1/8" 1-29/32" DUPLEX - DIE CAST ZINC UNIT. SHIP. UPC /8" * *For 1/2" knockout B=Width C = Thread length D = Clamping range A B C D /16" 1-21/32" 7/16" 1/8"-9/16"

82 B82 METAL CLAD CABLE CONNECTORS STEEL REDI-LOC R CONNECTORS Application For use in dry locations to connect MCI, AC and HCF cable to a box or enclosure Patented snap-in design MCI, AC and HCF Cable can be securely installed in outlet boxes or enclosures in seconds, without tools or locknuts Redi-Loc R Connectors cut installation time by 33% over competing termination methods Compact single unit design no need to worry about loose components or fumbling with protruding hardware Snaps tightly into the knockout no need to worry about a loose connection Reusable design installation can be reversed just as easily as it was originally installed Integral red insuliner provides for maximum wire protection and liner visibility for inspecting authorities Durable all steel construction Zinc electroplated for corrosion protection Tri-lingual (English, Spanish and French) installation instructions included in each unit carton UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances C22.2 #18 Reference Data REDI-LOC R connectors (2700, 2700AJ and 2701) U.S. Patent 5,731,543 COMING SOON REDI-LOC R CONNECTORS CONNECTORS FOR MCI, AC AND HCF CABLES STEEL ORDERING INFORMATION - REDI-LOC R CONNECTORS - CONNECTORS FOR MCI, AC AND HCF CABLES STEEL TRADE CABLE UNIT SHIP UPC SIZE SIZE /2" MCI Cable:.434"-.530" Alum. or.430"-.530" Steel Armored Cable (AC): /2 (.430) to 12/3 Alum. & Steel /2" Same info. as above 1 25 MCI Cable:.475"-.575" Alum. & 2700AJ 1/2" Steel. Armored Cable (AC): (.475) to 12-4 Alum. & Steel MCI Cable:.590"-.680" Alum. or /4".565"-.659" Steel Armored Cable (AC): 10/3 (.590") to 8/3 Alum. & Steel /4" Same info. as above 1 20 A B C 2700, 2700AJ 1.070".700".375" ".700".375" ".888".500" ".888".500" REDI-LOC SELECTION GUIDE 2700, AJ 2701, CABLE TYPE 1/2" KO 1/2" KO 3/4" KO 14/2, 14/3, 14/4, 12/2 AC Steel 12/3 14/2, 14/3, 14/4, 14/5 12/5, 10/2, 10/3, 10/4 12/3, 12/5, 10/2, HCF Steel Health Care Facilities 14/2, 14/3, 12/2, 12/3 14/2, 14/3, 12/2, 12/3 10/3, 10/4 w/grind 14/2, 14/3, 14/4, 12/2 14/2, 14/3, 14/4, 14/5 AC Aluminum 12/3 12/2, 12/3, 10/2 12/5, 10/2, 10/3, 10/4 MCI Steel (MCI Cables include 14/3, 14/4, 12/2, 12/3 12/4, 12/5, 12/6, 10/2 an add l ground wire) 14/2, 14/3, 12/2 10/2 10/3 MCI Aluminum (MCI Cables 14/3, 14/4, 12/2, 12/3 12/4, 12/5, 12/6, 10/2 include an add l ground wire) 14/2, 14/3, 12/2 10/2 10/3 COMING SOON B = Body width C=Throat I.D.

83 METAL CLAD CABLE CONNECTORS STEEL B83 Application For use in dry locations to connect MCI, AC and HCF cable to a box or enclosure Easy to install, just tilt, insert and snap down Tri-head screw/clamp design connector can be installed by using a slotted, Phillips or Robertson head screwdriver Integral insuliner provides for maximum wire protection 2800, 2801 Durable all-steel construction Zinc electroplated for corrosion ORDERING INFORMATION - protection Compliances CONNECTORS - FOR MCI, AC AND HCF CABLES - STEEL TRADE UNIT SHIP UPC SIZE C22.2 # /2" /4" COMING SOON SELECTION GUIDE CABLE TYPE /2" KO 3/4" KO AC Steel 14/2, 14/3, 14/4, 12/2, 12/3, 12/4, 10/2, 10/3 10/4, 10/5, 8/3, 8/4, 6/3 HCF Steel 14/2, 14/3, 12/2, 12/3, 10/2 AC Aluminum 14/2, 14/3, 14/4, 12/2, 12/3, 12/4 10/4, 8/3, 8/4 MCI Steel 14/2, 14/3, 14/4, 12/2, 12/3, 12/4, 10/2 10/3, 10/4, 8/2, 8/3 MCI Aluminum 14/2, 14/3, 14/4, 12/2, 12/3, 12/4, 10/2 10/3, 10/4, 8/2 MC Aluminum 14/3, 14/4, 12/2, 12/3, 12/4, 10/2, 10/3

84 B84 METAL CLAD CABLE CONNECTORS STEEL REDI-LOC R CONNECTORS Application For use in dry locations to connect MCI, AC and HCF cable to a box or enclosure Tri-Head screw/clamp design can accommodate two runs of MCI, AC and HCF Cable. Connector can be installed by using a slotted, Phillips or Robertson head screwdriver Reusable design installation can be reversed just as easily as it was originally installed Integral red insuliner provides for maximum wire protection and liner visibility for inspecting authorities Durable all steel construction Zinc electroplated for corrosion protection Tri-lingual (English, Spanish and French) installation instructions included in each unit carton UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances C22.2 #18 REDI-LOC R DUPLEX CONNECTOR - FOR MCI, AC AND HCF CABLES STEEL ORDERING INFORMATION - REDI-LOC R DUPLEX CONNECTOR - FOR MCI, AC AND HCF CABLES - STEEL TRADE CABLE UNIT SHIP UPC SIZE SIZE MCI Cable.450"-.545" Alum..425"-.550" Steel /2" MCI Cable.380"-.550" Alum Armored Cable (AC) 14/2 to 12/3 w/grnd Alum. and Steel /2" Same info. as above 1 10 REDI-LOC R SELECTION CHART CABLE TYPE 1/2" KO DUPLEX AC Steel 14/2, 14/3, 12/2, 12/3 HCF Steel Health Care Facilities 14/2, 14/3, 12/2, 12/3 AC Aluminum 14/2, 14/3, 12/2, 12/3 MCI steel (MCI Cables include 14/2, 14/3, 12/2, 12/3 an add l ground wire) MCI Aluminum (MCI Cables include 14/2, 14/3, 12/2, 12/3 an add l ground wire) B = Body height C=Throat I.D. D = Body width A B C D ".875".563" 1.719" ".875".563" 1.719"

85 METAL CLAD CABLE CONNECTORS MALLEABLE IRON/DIE CAST ZINC SET SCREW AND CLAMP TYPE CONNECTORS B85 Application For use in dry locations to connect MC/MCI cable to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliance SET SCREW MALLEABLE IRON CLAMP TYPE DIE CAST ZINC ORDERING INFORMATION - SET SCREW - MALLEABLE IRON CABLE UNIT SHIP UPC SIZE /2" Hub size for Steel MCI cable.450"-.560" dia. 50 B = Thread length C=Throat I.D. D = Screw spec A B C D /16" 19/32" 11/32" Fillister Head x 1/2" CLAMP TYPE - DIE CAST ZINC UNIT SHIP UPC /2" HUB SIZE FOR MC CABLE 2661 SELECTION CHART CABLE TYPE DIAMETER Rectangular Aluminum Corrugated.277"-.375" Aluminum Corrugated.365"-.510" Aluminum Smooth.345"-.525" Aluminum Interlocked.455"-.575" Steel Interlocked.435"-.547" B = Thread length C=Throat I.D. D = Clamping range E = Maximum body width THD. A B SPEC. C D E /32" 3/8" 1/2-14 3/8" 5/32"-5/8" 1-3/16"

86 B86 METAL CLAD CABLE CONNECTORS DIE CAST ZINC DUPLEX CONNECTORS Application For use in dry locations to connect MC/MCI cable to a box or enclosure Product Feature Rugged metallic construction insures mechanical protection for the raceway Compliance DUPLEX DIE CAST ZINC ORDERING INFORMATION - DUPLEX - DIE CAST ZINC UNIT SHIP UPC /2" HUB SIZE FOR MC CABLE 2611 SELECTION CHART CABLE TYPE DIAMETER Aluminum Smooth.410"-.500" Aluminum Interlocked.460" -.538" Steel Interlocked.438"-.560" A B C D /16" 1-21/32" 7/16" 1/8"-9/16" B=Width C = Thread length D = Clamping range

87 NONMETALLIC SHEATHED CABLE CONNECTORS SNAP-IN TYPE B87 Application For use in dry locations for connecting Nonmetallic Sheathed Cable (NMSC) to a box or an enclosure One-piece nonmetallic construction -resists corrosion and offers insulation protection Snap-in design for 1/2" K.O. s locks into the knockout securely. No need to waste time with installing locknuts Captive locking wedge no need to worry about missing components Easier to install than a standard die cast NMSC connector. No need to remove and retighten locknuts and cable clip screws. Just snap our connector into a box, insert the cable and compress the locking wedge Multipurpose design - offers installation flexibility. These connectors can accommodate a single run of 14-2 to 10-3 cable, a double run of 14-2 to 12-2 cable, and one or more.300 inch or one.600 inch diameter cord Innovative packaging configurations - Bulk packaging option saves volume users time and money. Smaller size carton quantities offer purchasing flexibility UPC bar coded fittings are individually polybagged with a preprinted UPC-A bar code and packaged in pre-scored tear top cartons for an attractive presentation Compliances For single cable and cord only SNAP-IN TYPE NONMETALLIC ORDERING INFORMATION - SNAP-IN TYPE - NONMETALLIC TRADE NONMETALLIC UNIT SHIP UPC SIZE CABLE SIZE Single 14-2 min to 10-3 max, Double /2" 14-2 min to 12-2 max. Flexible Cord Single.300 to.600 dia. Two dia. Single 14-2 min to 10-3 max, Double /2" 14-2 min to 12-2 max. Flexible Cord Single.300 to.600 dia. Two dia. Single 14-2 min to 10-3 max, Double /2" Single.300 to.600 dia. Two dia min to 12-2 max. 10 pcs 10 bags Flexible Cord per bag per ctn A B C /32" 1/2" 1-3/32" /32" 1/2" 1-3/32" /32" 1/2" 1-3/32" B = Length snap-in hub C = Maximum body width

RACO Commercial Fittings

RACO Commercial Fittings 06 Pg B1 - B20.qxp 6/9/2008 9:47 AM Page B1 RACO Commercial Fittings 06 Pg B1 - B20.qxp 6/9/2008 9:47 AM Page B2 B2 dbkbo^i=fkcloj^qflk=j=pq^ka^oapi=ommu=k^qflk^i=bib`qof`^i=`lab déåéê~ä=fåñçêã~íáçå tüéå=óçì=åééç=íç=åçìéäéi=åçååéåíi

More information

Conduit End Bells...EA1 Hex Reducing Bushings...EA2 Conduit Hubs...EA3-EA4. Split Couplings...EA5 Three Piece Couplings...EA6 Conduit Nipples...

Conduit End Bells...EA1 Hex Reducing Bushings...EA2 Conduit Hubs...EA3-EA4. Split Couplings...EA5 Three Piece Couplings...EA6 Conduit Nipples... SECTION E INDEX Product Description Page Number Conduit End Bells.......................................EA Hex Reducing Bushings..................................EA2 Conduit Hubs......................................EA-EA4

More information

BELL. RACO, TayMac and BELL offer a full line of electrical products that are ideally suited to help you complete your next solar project

BELL. RACO, TayMac and BELL offer a full line of electrical products that are ideally suited to help you complete your next solar project SOLAR RACO, TayMac and BELL offer a full line of electrical products that are ideally suited to help you complete your next solar project Commercial, Industrial and Residential Electrical Products RACO

More information

Zinc Cable & Conduit Connectors For Armored Cable, Flexible Metal Conduit & Metal Clad Cable

Zinc Cable & Conduit Connectors For Armored Cable, Flexible Metal Conduit & Metal Clad Cable For Armored Cable, Flexible Metal Conduit & Metal Clad Cable Type AC 90 2-Screw Clamp To make a 90 termination of conduit or cable to a knockout or unthreaded slip hole in a dry location box or enclosure.

More information

Ground Clamps Cable Tray

Ground Clamps Cable Tray commercial and industrial fittings: ing Fittings and Solderless Connectors Clamps Cable Tray Terminates ground wire to cable tray. For aluminum or copper conductors. 1 4 hex wrench tightens both tray and

More information

tings fi t fl ex/mc/ac

tings fi t fl ex/mc/ac 22 flex/mc/ac fittings Nothing can be more frustrating than losing valuable time due to low quality fittings. Madison s Flex/AC/ MC fittings come through for you time after time. Giving you affordability

More information

Description Cast Device Box, Height Inch; Width 2.81 Inch; Depth 2.69 Inch; Capacity 25 Cu Inch; 1 Gang; 2 Hub(S); Hub Location End;

Description Cast Device Box, Height Inch; Width 2.81 Inch; Depth 2.69 Inch; Capacity 25 Cu Inch; 1 Gang; 2 Hub(S); Hub Location End; 3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 1100 1G Mall Box Appleton/Oz Gedney Catalog Number 1100 Manufacturer Appleton/Oz Gedney Description Cast Device Box, Height

More information

GLOSSARY OF ELECTRICAL INDUSTRY TERMS

GLOSSARY OF ELECTRICAL INDUSTRY TERMS A ADD-A-DEPTH RING a means of extending the walls of a device box to the wall surface, providing a barrier between a wiring device and the surrounding wall material. AIR PLENUM a compartment or chamber

More information

Available in high-capacity. and assembled by hand for smooth operation. Durable chrome-plated finish. Heat-treated for long life.

Available in high-capacity. and assembled by hand for smooth operation. Durable chrome-plated finish. Heat-treated for long life. Klein s line of wrenches are forged from the finest steel and are designed to deliver great strength and long working life. Regardless of the job type, Klein has a wrench that will help the professional

More information

Wrenches. Wrenches. F o r P. r o f e. s s i o. n a l s. .. S i. n c e 1

Wrenches. Wrenches. F o r P. r o f e. s s i o. n a l s. .. S i. n c e 1 F o r P r o f e Klein s line of wrenches are forged from the finest steel and are designed to deliver great strength, and long working life. Regardless of the job type, Klein has a wrench that will help

More information

FSK1VDRA 1G Al DPLX RCPT CVR

FSK1VDRA 1G Al DPLX RCPT CVR 3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 FSK1VDRA 1G Al DPLX RCPT CVR Appleton/Oz Gedney Catalog Number Manufacturer Weight per unit Product Category FSK1VDRA

More information

commercial and industrial fittings: cast DEVICE BOXES Applications Illustrated Features

commercial and industrial fittings: cast DEVICE BOXES Applications Illustrated Features UNILETS for use with Threaded Rigid Conduit and IMC. All Device Boxes have Construction. Furnished with Internal Ground Screw. Applications Accommodate wiring devices such as switches and receptacles.

More information

E.M.T. Set-Screw Connectors. Technical Specifications

E.M.T. Set-Screw Connectors. Technical Specifications Set-Screw onnectors Regular Insulated I5404 (-IT) / I5408 (-IT) Steel Locknut I5004 (-IT) / I5008 (-IT) I5020 (-IT) / I5032 (-IT) I5410 (-IT) / I5432 (-IT) Steel Locknut I5010 (-IT) / I5016 (-IT) I5054

More information

Iberville. Commercial Grade Fittings EMT CI5410 / CI5432 CI5410IT / CI5432IT CI5404 / CI5408 CI5404IT / CI5408IT CI5004 (-IT) / CI5008 (-IT)

Iberville. Commercial Grade Fittings EMT CI5410 / CI5432 CI5410IT / CI5432IT CI5404 / CI5408 CI5404IT / CI5408IT CI5004 (-IT) / CI5008 (-IT) ommercial Grade Fittings Set-Screw Fittings I5404 / I5408 I5404IT / I5408IT I5004 (-IT) / I5008 (-IT) I5410 / I5432 I5410IT / I5432IT I5010 (-IT) / I5016 (-IT) Regular Insulated Set-Screw Fittings (Steel)

More information

COMMERCIAL AND INDUSTRIAL FITTINGS: CAST DEVICE BOXES. Applications

COMMERCIAL AND INDUSTRIAL FITTINGS: CAST DEVICE BOXES. Applications Blank Bodies for Brazed Hubs UNILETS for Use with Threaded Rigid Metal Conduit and IMC. Available with Hub Sizes from 1/2 through 1-1/2 (Union 1/2 through 1-1/4 ). Furnished with Internal Ground Screw.

More information

NEER Zinc Cable and Conduit Connectors For Flexible Metal Conduit

NEER Zinc Cable and Conduit Connectors For Flexible Metal Conduit For Flexible Metal Conduit SC: Straight Squeeze Type Connector These squeeze type connectors are used to terminate flexible metal conduit to a 1/2 knockout in a dry location box or enclosure. 1/2" and

More information

Beam and Purlin Clamps Beam Clamps

Beam and Purlin Clamps Beam Clamps Metal Framing & Cable Tray Steel City Hangers, Clamps & Fasteners Beam and Purlin Clamps Beam Clamps Fits beam flanges to 2" Supports 4" and 8" threaded rod, S-hooks, electrical boxes, conduit and bridle

More information

General Information...SA1-SA4

General Information...SA1-SA4 SECTION S INDEX Product Description Page Number General Information................................................................SA1-SA4 Type FSK Thruwall & Floor Seal For Conduit, Pipe or Tubing............................

More information

Thru Wall Floor Seals For New Installation

Thru Wall Floor Seals For New Installation The O-Z/Gedney Thruwall and Floor Seals provide a positive means of sealing pipe, conduit or tube where they pass through a concrete foundation of a structure below grade or below ground water level or

More information

4.3 Section CONDUIT INSTALLATION ACCESSORIES. Thinking of the environment. Fixing accessories Coupling accessories

4.3 Section CONDUIT INSTALLATION ACCESSORIES. Thinking of the environment. Fixing accessories Coupling accessories CONDUIT INSTALLATION ACCESSORIES Thinking of the environment We use only fully recyclable halogen-free thermoplastics, without harmful additives. No cadmium or asbestos in the colourants either. For total

More information

05 Pg A75-90.qxp 6/9/2008 9:36 AM Page A75 RACO Floor Boxes

05 Pg A75-90.qxp 6/9/2008 9:36 AM Page A75 RACO Floor Boxes 05 Pg A75-90.qxp 6/9/2008 9:36 AM Page A75 RACO Floor Boxes 05 Pg A75-90.qxp 6/9/2008 9:36 AM Page A76 A76 pq^ka^oapi=ommu=k^qflk^i=bib`qof`^i=`lab Δ déåéê~ä=^ééäáå~íáçåë o^`l=ñäççê=äçñéë=~êé=áçé~ääó=ëìáíéç

More information

Liquid Tight Conduit Connector With Internal Threads, Female Liquid Tight Conduit Fittings ( YCM )

Liquid Tight Conduit Connector With Internal Threads, Female Liquid Tight Conduit Fittings ( YCM ) Liquid Tight Conduit Connector With Internal Threads, Female Liquid Tight Conduit Fittings ( YCM ) No. Trade Dimensions (mm) Size I.D. A B C Threads YCM-03 3/8 11.2 28.3 44.6 13.2 PT 1/2 YCM-04 1/2 14.8

More information

Delikon Stainless Steel Liquidtight Connectors offer corrosion resistance and the strength of stainless steel for the highest levels of endurance.

Delikon Stainless Steel Liquidtight Connectors offer corrosion resistance and the strength of stainless steel for the highest levels of endurance. Corrosion Resistant liquid tight conduit fittings for use with flexible liquid tight metallic conduits, flexible liquid tight non metallic or PVC coated flexible metal conduit. * Liquidtight, Raintight,

More information

Overview The Thomas & Betts Method is Better. Just Four Easy Steps to a Perfect Connection! Step 1. Step 2

Overview The Thomas & Betts Method is Better. Just Four Easy Steps to a Perfect Connection! Step 1. Step 2 Overview The Thomas & Betts Method is Better. The Thomas & Betts method of installing compression connectors on power cables is designed to provide a high degree of reliability in electrical wiring. This

More information

CONTINUING EDUC ATION

CONTINUING EDUC ATION 3 CONTINUING EDUC ATION FOR WISCONSIN ELECTRICIANS 2017 NEC Article 250 2 Hours WISCONSIN CONTRACTORS INSTITUTE N16 W23217 Stone Ridge Drive Suite 290 Waukesha, WI 53188 262-409-4282 www.wcitraining.com

More information

TRANSMITTAL LETTER. As Builts Change Order Contract Copy of Letter Insurance. For approval Approved as submitted Resubmit copies for approval

TRANSMITTAL LETTER. As Builts Change Order Contract Copy of Letter Insurance. For approval Approved as submitted Resubmit copies for approval Redwood City Electric, Inc. TRANSMITTAL LETTER To: Transworld Construction, Inc. 1178 Folsom Street San Francisco, CA 94103 Date: 05/31/12 Job #: 9340 Regarding: SFO DATA CENTER Attn: Rob Acero We are

More information

INTERMEDIATE METAL CONDUIT

INTERMEDIATE METAL CONDUIT PRODUCT GUIDE 08 CONDUIT PIPES CONDUIT FITTINGS FITTINGS FOR FLEXIBLE CONDUITS METALLIC ELECTRICAL BOXES AND COVERS CONDUIT BODIES WEATHERPROOF BOXES AND COVERS CHANNELS & SUPPORTS METAL ENCLOSURES CHANNELS

More information

Complete line of Holemaking Products and Accessories

Complete line of Holemaking Products and Accessories Complete line of Holemaking Products and Accessories I N T R O D U C I N G Holemaking Products Klein Tools has expanded our line of Holemaking products. We have added new flexible drill bits and related

More information

Steel City Comparison & Strategy. vs. T&B Liquidtight Fittings. Andrea Briggs. Associate Product Manager - Conduit & Fittings FOR INTERNAL USE ONLY

Steel City Comparison & Strategy. vs. T&B Liquidtight Fittings. Andrea Briggs. Associate Product Manager - Conduit & Fittings FOR INTERNAL USE ONLY Comparison & Strategy Andrea Briggs Associate Product Manager - Conduit & Fittings Liquidtight Fitting Brand Strategy Component Comparisons Summary Liquidtight Fitting Brand Strategy Steel City Liquidtight

More information

Electrical Construction Name:

Electrical Construction Name: Tools of the Trade The following are common tools that are used in the electrical industry. This hand-out is to help familiarize you with the tools, the terminology, and their use. Retractable Steel tape

More information

Bulletin 800H Hazardous Location Push Buttons Product Overview/Specifications. Table of Contents See below.

Bulletin 800H Hazardous Location Push Buttons Product Overview/Specifications. Table of Contents See below. Bulletin H Product verview/specifications Bulletin H/ Hazardous locations push buttons and stations Classes I, II & III Divisions & / in. - NPSM barrel Type & Explosion-proof operators Table of Contents

More information

Ford Water Meter Couplings & Accessories

Ford Water Meter Couplings & Accessories Section H 2/2001 Ford Water Meter Couplings & Accessories The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260/563-3171 FAX: 1-800-826-3487 Overseas

More information

Spring Steel Fasteners

Spring Steel Fasteners Cable Support Supports up to 4 runs of MC and AC cable and up to 6 runs of nonmetallic sheathed cable Installs with nails or staple or sheet metal screws Complies with CEC article 12-516 for all wood and

More information

mila-wall (Series100) General Operating Instructions page 1 of 15

mila-wall (Series100) General Operating Instructions page 1 of 15 mila-wall (Series100) General Operating Instructions page 1 of 15 Step #1: Before setting up walls, lower adjustable leveling feet on each panel approximately 1". This will allow access to the threaded

More information

U CON DUIT CODEGUARD. 10-IN-1 UNIVERSAL CONDUIT BODY for RIGID/IMC or EMT. Service Truck Solutions

U CON DUIT CODEGUARD. 10-IN-1 UNIVERSAL CONDUIT BODY for RIGID/IMC or EMT. Service Truck Solutions U CON DUIT CODEGUARD MKG420CS 10-IN-1 UNIVERSAL CONDUIT BODY for RIGID/IMC or EMT Configures to all standard bodies ( LB, LR, LL, T, C ) Three 1/2" threaded hub weatherproof box Space Saver! & Trip Saver!

More information

Nemalux INSTALLATION INSTRUCTIONS APPLICATION 1-4

Nemalux INSTALLATION INSTRUCTIONS APPLICATION 1-4 I N D U S T R I A L rev. A- INSTALLATION INSTRUCTIONS *PENDING* E77827 E77827 APPLICATION MR3 & MR6 Luminaires are suitable for use in the following areas as defined by the National Electrical Code (NEC)

More information

Hose Accessories. "Air King" 4 - Lug Quick-Acting Couplings. Hose End. Female N.P.T. End

Hose Accessories. Air King 4 - Lug Quick-Acting Couplings. Hose End. Female N.P.T. End "Air King" 4 - Lug Quick-Acting 1¼" 1½" AM16 AM AM6 AB16~ AB~ AB6 End Rubber Washers for 4-Lug AWR14 Fits all sizes 1¼" 1½" AM18 AM3 AM8 AB18~ AB3 AB8 Rated to 1 PSI Female N.P.T. End "Boss" clamps recommended

More information

Waterpipe Ground Clamps. 1/2 in., 3/4 in., 1 or rebar /4 in., 1-1/2 in. or 2 in. 4 #6, #4, #2 AWG

Waterpipe Ground Clamps. 1/2 in., 3/4 in., 1 or rebar /4 in., 1-1/2 in. or 2 in. 4 #6, #4, #2 AWG Waterpipe Ground Ground Wire Size Water Pipe Size 2-T 1/2 in., 3/4 in., 1 or rebar 4-10 3-T 1-1/4 in., 1-1/2 in. or 2 in. 4 #6, #4, #2 WG 2-1/2 in., 3 in. or 3-1/2 in. 5-T 4 in., 4-1/2 in. or 5 in. 6 6

More information

Cast Iron Junction Boxes

Cast Iron Junction Boxes Cast Iron I. Purpose of Enclosure Enclosures are used to protect personnel against accidental contact with enclosed electrical devices or connections and to protect the enclosed devices or connections

More information

Stud Wall Pages

Stud Wall Pages Pages 125-144 125 Box Mounting Bracket For Electric Box Easily attaches 4" and 411 /16" outlet boxes to metal stud (HS3 switch boxes). Support leg reduces movement of box in wall. Can be attached to metal

More information

HANDHOLE SEAT GRINDER

HANDHOLE SEAT GRINDER 1041-1601 HANDHOLE SEAT GRINDER OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 9/17/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND UNDERSTAND OPERATOR S MANUAL. Thomas C. Wilson,

More information

SEALING METHODS AND HARDWARE FOR EQUIPMENT AND PROCESSES APRIL 11-12, 2018

SEALING METHODS AND HARDWARE FOR EQUIPMENT AND PROCESSES APRIL 11-12, 2018 SEALING METHODS AND HARDWARE FOR EQUIPMENT AND PROCESSES APRIL 11-12, 2018 SEALING METHODS AND HARDWARE FOR EQUIPMENT AND PROCESSES INTRODUCTION to APM HEXSEAL PURPOSE To review various ways to seal equipment

More information

Spun Copper Bullet C to 277 Volt Spun Copper LED revision 11/7/14 kl_c24led_spec.pdf

Spun Copper Bullet C to 277 Volt Spun Copper LED revision 11/7/14 kl_c24led_spec.pdf Catalog number: ing Options: Ordered Separately from See pages 3-5 Approvals: Date: Page: 1 of 5 Specifications 6K" DIA. (165.1 mm) Ordering Information 13J" (336.6 mm) K" NPT 2B" (54.0 mm) Source l S3/9L3KUV

More information

Steel Construction Tools

Steel Construction Tools F o r P Steel Construction Tools r o f e s s i o n a l s. Klein has combined unique design features with skillful engineering and manufacturing to create a superior line of steel construction tools. These

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory FABRIC REAR DOORS (5P) P/N 0SR90-HL4-211B (BLACK) P/N 0SR90-HL4-211C (CAMO) Application SXS1000M5P/M5D Honda Dealer: Please give a copy of these instructions to your

More information

Holemaking Products & Accessories

Holemaking Products & Accessories Holemaking Products & Made of top-of-the-line materials for longer lasting performance, Klein's diverse line of drill bits and holemaking products and accessories provide accuracy and consistency to get

More information

Flange Dimensions Class 125 Bronze Flange Dimensions Class 300 Bronze Flange Dimensions Class 150 Bronze Flange Dimensions

Flange Dimensions Class 125 Bronze Flange Dimensions Class 300 Bronze Flange Dimensions Class 150 Bronze Flange Dimensions Dimensions Class Bronze Dimensions Meets Ib. A.S.M.E. Stard Class 00 Bronze Dimensions Meets ANSI STD B. Nominal Dim. A O.D. Dim. B Circle Dim. C Hole No. Holes Nominal Dim. A Diam. Dim. B Min. Dim. C

More information

11 6 Round Building Assembly Instructions

11 6 Round Building Assembly Instructions 11 6 Round Building Assembly Instructions 11 6 Round Building Hardware List 1. Pro Rib Brite White 36 Wide X 68 Long (Siding Steel) 11 2. Top Wall Wheel Ring 3 3. Base Ring 3 4. 1 ½ X 68 Aluminum Tubes

More information

Color-Keyed. Compression Connector System. Table of Contents

Color-Keyed. Compression Connector System. Table of Contents Table of Contents The Thomas & Betts method of installing compression connectors on power cables is designed to provide a high degree of reliability in electrical wiring. This method allows electrical

More information

Connection by Compression

Connection by Compression Connection by Compression.............. -5 Color-Keyed Connectors................ -9 Connectors for Copper Conductor........ 0-9 Cast Copper Connectors for Copper Conductor.................. 0- Flag Connectors

More information

Main Components. Pipe and Bolt Threading Machine 300/300A. Early Style. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A.

Main Components. Pipe and Bolt Threading Machine 300/300A. Early Style. Printed in U.S.A. Ridge Tool Company/Elyria, Ohio, U.S.A. Pipe and Bolt Threading Machine 00/00A Main Components Early Style 0 0 * 0 0 0 For Information on Cutters, Die Heads and Reamers SEE INDEX Ref. 0 0 Catalog 0 00 00 0 0 0 00 0 0 0 0 0 0 0 00 0 00 00 00

More information

WESTERN WIRE PRODUCTS

WESTERN WIRE PRODUCTS WESTERN WIRE PRODUCTS Celebra ng 100 years of Quality and Service 1914 2014 Thanks to our dedicated employees and customers we are celebra ng 100 years of being in business and we look forward to servicing

More information

PIPE/CONDUIT SUPPORTS

PIPE/CONDUIT SUPPORTS PIPE/CONDUIT SUPPORTS Pipe/Conduit Clamps...102-105 Unicushion... 106 Pipe & Tubing (Cush-A-Clamp ) Clamps...107-110 Pipe Hangers... 111 Pipe Rollers...111-112 Pipe Brackets... 113 Reference Tables...114-120

More information

Floor Boxes. Concealed Service Floor Boxes. Engineering Data 663 Series. Faces Plates for 663 Floor Box. 663 Series Floor Box

Floor Boxes. Concealed Service Floor Boxes. Engineering Data 663 Series. Faces Plates for 663 Floor Box. 663 Series Floor Box Concealed Service Floor Boxes 663 Series Floor Box 663-SC Multiple service floor box that delivers power, communications and data from standard conduit with no exposed service fitting Result: Open office

More information

The V2100 Series Steel Raceway provides wiring

The V2100 Series Steel Raceway provides wiring V2100 Steel Raceway Two-Piece Surface Raceway The V2100 Series Steel Raceway provides wiring capacities for small to medium size installations. Power or Data/Communication Devices can be wired into the

More information

WEBS-MT/R Tower Installation Instructions

WEBS-MT/R Tower Installation Instructions I. Introduction This manual is for tower installation only. For instructions on installing the anchor bolts into the foundation, see the ETP-MT/R Anchor Bolt Installation Instructions. II. Contents Before

More information

Product #: Product #:

Product #: Product #: STANLEY FATMAX Push-Lock Groove Joint Pliers Multi-purpose jaws designed to grasp flat and round objects. Push-Lock technology allows for quick and easy adjustment in 17 positions. Induction hardened jaws

More information

Sensor Accessories Retroreflectors and Retroreflective Tape 8-2

Sensor Accessories Retroreflectors and Retroreflective Tape 8-2 - Retroreflectors and Retroreflective Tape PG.05E.17.T.E Retroreflectors Contents Overview.................... - Model Selection............... -3 Dimensions.................. -3 High Quality Retroreflectors

More information

Holemaking Products & Accessories

Holemaking Products & Accessories Holemaking Products & Holemaking Products & Made of top-of-the-line materials for longer lasting performance, Klein's diverse line of drill bits and holemaking products and accessories provide accuracy

More information

ASAP Sr. A Strap and Pole. Magic Christmas. Single Stage. Walter Monkhouse. Alexandria, La. Version 1.2.

ASAP Sr. A Strap and Pole. Magic Christmas. Single Stage. Walter Monkhouse. Alexandria, La. Version 1.2. ASAP Sr Single Stage A Strap and Pole Version 1.2 Walter Monkhouse Walter@MagicChristmas.org Magic Christmas Alexandria, La. Description The ASAP Sr, single stage, has the same concept as the ASAP Jr.

More information

Copper Tubing Hangers Clevis Hangers. Copper Tubing Hangers

Copper Tubing Hangers Clevis Hangers. Copper Tubing Hangers Copper Tubing Hangers Clevis Hangers Copper Tubing Hangers Fig. CT-69 Adjustable Swivel Rug Fig. CT-138R Fig. CT-65 Fig. CT-109 Extension Split Light Weight Adjustable Clevis Fig. CT-99 & CT-99C Split

More information

M2 Antenna Systems, Inc. Model No: YAGI ANTENNA

M2 Antenna Systems, Inc. Model No: YAGI ANTENNA M Antenna Systems, Inc. Model No: 4.5-7 YAGI ANTENNA SPECIFICATIONS: Model... 4.5-7 Frequency Range... 4.0 To 4.5 MHz *Gain... 0 To 7 dbi Front to back... 0 db over the rear 80 Beamwidth... E=44 H=50 typical

More information

PRODUCT MANUAL 5-IN-1 MITER SAW STATION *SAVE THIS MANUAL FOR FUTURE REFERENCE

PRODUCT MANUAL 5-IN-1 MITER SAW STATION *SAVE THIS MANUAL FOR FUTURE REFERENCE PRODUCT MANUAL 5-IN-1 MITER SAW STATION *SAVE THIS MANUAL FOR FUTURE REFERENCE 92778 1 GENERAL SAFETY INFORMATION For your safety, please read these instructions carefully before use and keep them in the

More information

Connection by Compression

Connection by Compression Connection by Compression.............. -5 Color-Keyed Connectors................ -9 Connectors for Copper Conductor........ 0-9 Cast Copper Connectors for Copper Conductor.................. 0- Flag Connectors

More information

Professional Pliers. Quality to Depend on

Professional Pliers. Quality to Depend on Professional Pliers Quality to Depend on - 227 - High Leverage Pliers High Leverage Pliers High Leverage pliers boast a labor-saving design to generate greater productivity with less effort. Ergonomic

More information

101B, 210X, ELM, VSTB Installation Manual

101B, 210X, ELM, VSTB Installation Manual 101B, 210X, ELM, VSTB Installation Manual 99-16105-I001 Copyright 2010 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in examples

More information

4 INSTALLATION Requirements on Installation Securing Space Before installing the Panaboard, be sure to secure space shown in section 2.6.

4 INSTALLATION Requirements on Installation Securing Space Before installing the Panaboard, be sure to secure space shown in section 2.6. 4 INSTALLATION The Panaboard is used by hanging it on the wall or installing it on the stand (sold separately as an option). When using the Panaboard by hanging it on the wall, refer to the description

More information

Arducopter 3DR-B Hardware

Arducopter 3DR-B Hardware Arducopter 3DR-B Thank you for purchasing an Arducopter 3DR kit. The Arducopter 3DR is a stable and supported quadrotor frame in the ongoing development of the Arducopter code on DIYDrones. It features

More information

Carton of 1, B. Min. 2-,34mm 2 Max. 3-1,5mm V 22 to 14 AWG Min. 2 #22 Max. 3 #16. ,34mm 2 to 2,5mm 2. Min.

Carton of 1, B. Min. 2-,34mm 2 Max. 3-1,5mm V 22 to 14 AWG Min. 2 #22 Max. 3 #16. ,34mm 2 to 2,5mm 2. Min. Wire-Nut Five color-coded models cover wire sizes from 22 to 6 AWG Fixed, square-wire spring creates its own threads maintains a secure positive grip that will not relax over time No pre-twisting required

More information

Series 1600 WeatherGuard Dock Enclosure

Series 1600 WeatherGuard Dock Enclosure Fairborn USA Inc. 205 Broadview Street Upper Sandusky, OH 43351 1-800-262-1188 Fax 1-419-294-4980 Series 1600 WeatherGuard Dock Enclosure All Models! WARNING Do not install this product unless you read

More information

MC CHANGER CABINET INSTALLATION INSTRUCTIONS

MC CHANGER CABINET INSTALLATION INSTRUCTIONS 8M00356 REV. 10 www.standardchange.com 1-800-968-6955 Technical Phone Support is from 8:00AM to 7:30PM E.S.T., Monday-Friday Walk-in Service is from 8:00AM to 4:30PM E.S.T., Monday-Friday Parts Department

More information

MECKLENBURG COUNTY. Land Use and Environmental Service Agency Code Enforcement 9/8/10 ELECTRICAL CONSISTENCY MEETING. Code Consistency Questions

MECKLENBURG COUNTY. Land Use and Environmental Service Agency Code Enforcement 9/8/10 ELECTRICAL CONSISTENCY MEETING. Code Consistency Questions conduit? 9/8/10 ELECTRICAL CONSISTENCY MEETING Code Consistency Questions 1. Can branch circuits of different services be installed in the same Yes, see 300.3(C)(1) for conductors of different systems

More information

Special Thumb Screw Order Form

Special Thumb Screw Order Form Special Thumb Screw Order Form QUOTE FOR: ORDER FOR: Name: Company: Address: QUANTITY: Phone #: City: State: Zip: Email Address: FILL IN YOUR DIMENSIONS write directly over light blue type* write clearly

More information

ASSORTMENTS BRONZECLASSWB Above assortment with one #99901 Cabinet, 17 extra dividers, all drawers pre-labeld inside and out.

ASSORTMENTS BRONZECLASSWB Above assortment with one #99901 Cabinet, 17 extra dividers, all drawers pre-labeld inside and out. ASSORTMENTS 34 s BRONZECLASS Body Shop Fastener Starter 71 of the most popular items - Over 1700 pieces. Fasteners Only - No Bins Box Qty. 1 Inside of drawer BRONZECLASSWB Above assortment with one #99901

More information

INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE

INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE INSTRUCTIONS FOR AIRFLEX 36WCBEP/36WCSEP WEAR PLATE REPLACEMENT USING GASKET SEALING TAPE The material included in this kit is to be used for WC styles of brakes that are designed or upgraded to the EP

More information

LENGTH IDENTIFICATION

LENGTH IDENTIFICATION 58 Power-Bolt HEAVY DUTY, ELF-UNDERCUTTING LEEVE TYPE BAE MATERIAL Concrete, Block, Brick, tone IZE RANGE 1/4" x 1" to 1-1/4" x 9 MATERIAL LENGTH IDENTIFICATION The Power-Bolt anchor has a length identification

More information

Tel / (USA & CANADA) /

Tel / (USA & CANADA) / Tel.58.847 / 8.388.459 (USA & CANADA) / Email sales@msdiscounttool.com MULTIPURPOSE CLAMPS - USA SERIES 7: Lightweight and 4% stronger than C clamps. Floating jaws that always stay parallel. Designed to

More information

content Introduction Some good reasons to use SMARTr products Reducers, Plugs Conduit Reducer Stopping Plug

content Introduction Some good reasons to use SMARTr products Reducers, Plugs Conduit Reducer Stopping Plug CONTENT 1 2 Introduction Some good reasons to use SMARTr products G.I. CONDUITS SMARTr BS4568 : PT1 : 1970 Class 4, IEC 61386-21 : 2004 IEC60614-2 - 1 : 1993, BS EN 50086-2 -1 : 1996 SMARTr BS4568 : PT1

More information

Micro-Flood EL / 277 Volt Die-Cast Aluminum LED revision 4/11/11 el217.pdf

Micro-Flood EL / 277 Volt Die-Cast Aluminum LED revision 4/11/11 el217.pdf Catalog number: / Mode Options: See page 2 ing Options: See pages 3-5 Approvals: Date: Page: 1 of 5 Specifications Housing and Lens Frame: Die-cast low copper alloy (

More information

Series 5 Die Cast Aluminum Conduit Outlet Bodies, Covers and Gaskets

Series 5 Die Cast Aluminum Conduit Outlet Bodies, Covers and Gaskets Eaton's Crouse-Hinds Series 5 die cast copper-free aluminum conduit bodies, covers and gaskets are available for use with rigid or EMT conduit (with set screw). Conduit bodies are available in trade sizes

More information

CRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 10/24/2014 SHEET 1 of 24

CRP700 Benchtop Basic CNC Machine Assembly Instructions. Updated 10/24/2014 SHEET 1 of 24 CRP700 Benchtop Basic CNC Machine Assembly Instructions Updated 0//0 SHEET of NOTE: This piece of extrusion is mounted wide side up Quick Tip: Lay extrusion on table as shown for easy assembly BASE ASSEMBLY:.

More information

Pow-R-Feed Systems Service Manual

Pow-R-Feed Systems Service Manual Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious

More information

Overtravel of 3.5 mm max. Power source DC D5C-1DS0 D5C-1DP0 D5C-1DA0 AC D5C-1AS0 D5C-1AP0 D5C-1AA0 Antenna only D5C-00S0 D5C-00P0 D5C-00A0

Overtravel of 3.5 mm max. Power source DC D5C-1DS0 D5C-1DP0 D5C-1DA0 AC D5C-1AS0 D5C-1AP0 D5C-1AA0 Antenna only D5C-00S0 D5C-00P0 D5C-00A0 Touch Switch Unique 18 mm Capacitive Touch Switch with Choice of Three Actuators is Activated with Only a Very Slight Physical Contact Lightweight objects, such as thin wire or foil can be accurately detected.

More information

SECTION DISTRIBUTION SWITCHBOARDS

SECTION DISTRIBUTION SWITCHBOARDS PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 24 13 DISTRIBUTION SWITCHBOARDS SPEC WRITER NOTE: Delete between // -- // if not applicable to project. Also delete any other item or paragraph not applicable

More information

STAR TOOL SUPPLY / GRAND TOOL SUPPLY

STAR TOOL SUPPLY / GRAND TOOL SUPPLY MULTIPURPOSE CLAMPS - USA SERIES 7: Lightweight and 4% stronger than C clamps. Floating jaws that always stay parallel. Designed to eliminate distorting or twisting action. Cantilever action provides 4:

More information

SIGN MOUNTED BEACON SIG-027-A SINGLE SIGN MOUNTED FLASHING BEACON INSTALLED ON ONE WOOD POST DETAIL "A-1"

SIGN MOUNTED BEACON SIG-027-A SINGLE SIGN MOUNTED FLASHING BEACON INSTALLED ON ONE WOOD POST DETAIL A-1 1 1/2" x 60" Galvanized (thread both ends) Top Bolt See Detail "A-1" and Slotted Channel Parallel Conduit Clamp Warning Sign 3 Equal Bolt Spacings (3 places at 12" min. spacing) (1) 3/8"x 7" min. (4"x

More information

Cat. No. A1200 A1200-S A1200-KO. Finishes & Materials. E142-1/4x100EG 1/4 x 1 A100-5/16EGC A100-3/8EGC. Standard Finish: Electrogalvanized

Cat. No. A1200 A1200-S A1200-KO. Finishes & Materials. E142-1/4x100EG 1/4 x 1 A100-5/16EGC A100-3/8EGC. Standard Finish: Electrogalvanized Superstrut Support Systems 1-5/8 in. x 1-5/8 in. Channel and Hardware Superstrut 1-5/8 in. x 1-5/8 in. - 12 Gauge Channel Type A Solid Base Punched Description Solid base -P Punched -HS Half slots Half

More information

REGATTA PATH LIGHT (RGP)

REGATTA PATH LIGHT (RGP) NEEDED FOR INSTALLATION: 5/64 & 5/32 Allen Wrench Waterproof Wire Connectors Warning Low Voltage Hot Surface Wear Gloves By Others Gloves IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

More information

Operating Instructions For Lockformer Button Punch Flanger

Operating Instructions For Lockformer Button Punch Flanger Capacity: 20 to 28 Gauge Galvanize Operating Instructions For Lockformer Button Punch Flanger To satisfactorily form the 90º button punch flange on light gauge materials, it was necessary to form the metal

More information

Overview Special Lugs for Special Problems Angled, Shaped and Trimmed the Way You Need Them

Overview Special Lugs for Special Problems Angled, Shaped and Trimmed the Way You Need Them Special Lugs for Special Problems Angled, Shaped and Trimmed the Way You Need Them Thomas & Betts can solve your difficult wire bending and terminating problems in confined power distribution panels, switchgear

More information

8" STEEL HOPPER AUGER

8 STEEL HOPPER AUGER " STEEL HOPPER AUGER REF # PART # DESCRIPTION Sold By 1 01-00001 " or 10" HYDRAULIC MOTOR ea. 2 01-0000 O-RING ea. 000-01000 MANUAL FLOW CONTROL BLOCK c/w REF#2& ea. 010-00001 /1" x 2" SOCKET HEAD BOLT

More information

ANCHORS SLEEVE ANCHORS BOLT DIAMETER

ANCHORS SLEEVE ANCHORS BOLT DIAMETER SLEEVE ANCHORS No hole spotting. No mis-alignments. Simply drill through the fixture into concrete, insert and tighten. Preassembled for fast, easy installation. No special tools necessary; meets federal

More information

o r r o s i o n s o l u t i o n s 805.409.4050 www.okote.net I I the o kote AdVAntAGE A tradition of High standards in orrosion Protection orrosive elements cause millions of dollars in damage through

More information

J-BOX. 3-O or 4-0 MUD RING J-BOX BRACKET BAR CABLE GRIPPER/ CANOPY MOUNTING STUD 8-32 BRACKET BAR SCREWS CANOPY STRAIN RELIEF POWER CORD CANOPY

J-BOX. 3-O or 4-0 MUD RING J-BOX BRACKET BAR CABLE GRIPPER/ CANOPY MOUNTING STUD 8-32 BRACKET BAR SCREWS CANOPY STRAIN RELIEF POWER CORD CANOPY KELSEY - CSS Cable Suspended Rotational and Static CSS - Cable Suspended 3-O or 4-0 MUD RING BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS STRAIN RELIEF POWER CORD MOUNTING GRIPPER AIRCRAFT CABLE CABLE

More information

DX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations

DX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations ASSEMBLY GUIDE DX-TVMLPTB03 Low-Profile TV Wall Mount For either wood-stud or concrete wall installations Safety information and specifications...2 Tools needed...........................3 Package contents......................3

More information

Linear Motion and Assembly Technologies Aluminum Framing /07. Die-Cast Foundation Brackets 3-10 & 3-11

Linear Motion and Assembly Technologies Aluminum Framing /07. Die-Cast Foundation Brackets 3-10 & 3-11 -0 Linear Motion and ssembly Technologies luminum Framing 91 500 1 /07 Section : Profile onnectors Overview One of the greatest strengths of the osch Rexroth structural aluminum framing system is the wide

More information

PSOL. Remove mounting screws. Remove ears. Add 6" leads PSOL = #12 AWG solid PSTR = #12 AWG stranded

PSOL. Remove mounting screws. Remove ears. Add 6 leads PSOL = #12 AWG solid PSTR = #12 AWG stranded Switch Options Work Smarter Not Harder Arrow Hart custom configured wiring devices can match any of your complex industrial or commercial job needs, simplifying your project and maximizing your bottom

More information

Lok Fast Column Clamp General Information

Lok Fast Column Clamp General Information Lok Fast Column Clamp General Information Gates Lok-Fast Column Clamp Has These Advantages: Can Be Job Built Gang Formed No Loose Pieces Designed For Rapid Placement of Concrete Rapid Locking Action 3

More information

Superstrut. Metal Framing. Beam Clamps. Design Loads. Finishes and Special Materials

Superstrut. Metal Framing. Beam Clamps. Design Loads. Finishes and Special Materials Loads Where design loads are indicated, they provide for a safety factor of 3 in conformance with the merican Standard Code for Pressure Piping. For more information, see page 57 for Engineering Data and

More information

HEAVY DUTY 11 STEEL CABINET

HEAVY DUTY 11 STEEL CABINET HEAVY DUTY STEEL CABINET ASSEMBLY INSTRUCTIONS ONE DRAWER BASE CABINET 05-206 Parts List Part No Description Qty Image ONE DRAWER BASE CABINET Part No Description Qty Image SB- Cabinet Body EH-0 Euro Hinge

More information