The better way to build TM. Installation Manual ROOF SIPs

Transcription

1 The better way to build TM Installation Manual ROOF SIPs

2 August 2017 ROOF SIPs Installation Manual Table of Contents Topics General Requirements Materials Electrical Wiring Interior Finish Exterior Cladding Materials Estimation Details Air Barrier Details for Air Barrier Sealants AB-1 Air Barrier Details for Sealing SIP Connections AB-2 Vapour Barrier Details for Vapour Sealing SIP Connections.... VB-1 Typical Roof Ridge R-1 Roof Ridge Details for 12/12 Pitch Roof R-2 Beam Pocket Detail R-3 Roof Valley & Intermediate Roof Support R-4 Eave Detail and Roof Support at Exterior Wall R-5 Typical Sloped Roof Assembly R-6 Sloped Roof Assembly with Ridge Beam R-7 Flat Roof Assembly R-8 Skylight Opening & Assembly R-9 Typical Roof Connection Sections (Roof to Wall) R-10 Roofing Applied to SIPs R-11 Flat Roofing Applied to SIPs R-12 LED Pot Light Installation in Ceiling SIPs R-13 Roof Overhang Eave Details (Timberframe) R-TF-1 Roof Overhang & Rake (Timberframe) R-TF-2 Roof SIP - Installation Manual 2

3 August 2017 ROOF SIPs Installation Manual 1. General Requirements 1.1 Scope The basic design and construction requirements for the Thermapan Structural Insulated Panel (SIP) roof system is set forth in this specification. Criteria for materials, environmental control, design loads, and structural design are included. Where requirements are based on internationally recognized standards and specifications, these standards and specifications are referenced without elaboration. Installers shall reference engineering design package for fastening arrangements. 2. Materials 2.1 The Thermapan Roof SIP is composed of an expanded polystyrene (EPS) foam core laminated between two layers of oriented strand board (OSB) with a structural adhesive. 2.2 Framing Lumber shall be DOC PS 20 or NLGA No.2 or better. 2.3 Wire nails, ring nails, spikes and staples shall conform to CSA B111 or ANSI/ASME B Wood screws shall conform to ANSI/ASME B SIP screws shall conform to ICC-AC Caulking Compounds shall conform to CAN/CGSB or ASTM C Polyethylene Sheeting shall conform to CAN/CGSB-37.2, CAN/ CGSB-37.16, or ASTM D Low expansion foam seal shall conform to AAMA Structural adhesive shall conform to CAN/CGSB 71GP26, APA AFG-01 or ASTM D Electrical Wiring 3.1 An optional furring for electrical passage should be fastened to the underside of the roof SIP between the vapour barrier and the interior finish. See details R-1, R-4 and R-5. Roof SIP - Installation Manual 3

4 August Interior Finish 4.1 The interior of the roof SIP can be finished with any of the common required building code materials. It is recommended that the SIP joints and connections be sealed as per Details AB-1, AB-2 and VB Exterior Roofing 5.1 Consult your local building code and refer to details R-11 and R-12 for roofing applied to SIPs. Roof SIP - Installation Manual 4

5 August 2017 MATERIALS ESTIMATING Roof (Vaulted Ceiling) Estimation Only Lumber Requirements: Perimeter of roof or fascia length Caulking and Sealant Requirements: Every 1200 sqft (111 m 2 ) of SIP equals 1 case of Expandable Foam Every 2000 sqft (185 m 2 ) of SIP requires 1 case of Sealant Fasteners: Recommend 2 (50mm) Ring nail or 2 (50mm) screws for connection to panel ~ 1.25 times the square footage of SIPs... nailing of spline SIP screws use 40% of Roof square footage Roof SIP - Installation Manual 5

6 AIR BARRIER RECOMMENDED DETAILS FOR AIR BARRIER SEALANTS All sealants, FOAM (A) or CAULKING (B), should be applied onto the SIP in a continuous rectangular pattern along the outer most edge of the area to be sealed. (A) A low expansion FOAM SEALANT should conform to the AAMA standard. Apply a 1/2 inch or a 12.5 mm diameter of a continuous bead of expandable foam sealant onto the SIP: Expandable Foam Sealant Bead EPS (B) A CAULKING SEALANT should conform to ASTM C and/or CAN/CGSB M. Apply a 3/8 inch or a 10 mm diameter continuous bead of caulking onto the lumber spline: CAULKING (CONTINUOUS BEAD) Caulking Bead LUMBER STUD OR SPLINE AIR BARRIER DETAILS FOR AIR BARRIER SEALANTS DWG. No. NOVEMBER AB-1

7 AIR BARRIER RECOMMENDED DETAILS FOR SEALING SIP CONNECTIONS (1) Foam to Foam: Use a low expansion foam sealant. 1/4 (6 mm) GAP FOAM SEALANT FOAM SEALANT SIP SPLINE JOINT SEE VAPOUR BARRIER DETAIL (VB-1) BUTT JOINT (2) Foam to Wood: Use a low expansion foam sealant. PLATES SECTION LUMBER SPLINES CAP TOP PLATE FOAM SEALANT CAULKING (SEE WOOD TO WOOD) FOAM SEALANT BOTTOM PLATE LUMBER SPLINE, END STUD OR JOIST (3) Wood to Wood: Use caulking and a low expansion foam sealant. CORNER DETAIL PLAN LUMBER SPLINE FOAM SEALANT SEE VAPOUR BARRIER DETAIL (VB-1) FOAM SEALANT FOAM SEALANT CAULKING (SEE AB-1) CAULKING (SEE AB-1) AIR BARRIER DETAILS FOR SEALING SIP CONNECTIONS MAY 2009 DWG. No. AB-2

8 VAPOUR BARRIER RECOMMENDED DETAILS FOR VAPOUR SEALING SIP CONNECTIONS The function of a vapour barrier is to control the entry of water vapour into the building assembly. Vapour barriers should not be confused with an air barrier. All SIP seams and connections must be VAPOUR SEALED from the INTERIOR. These are recommended vapour barrier methods: OSB EXTERIOR INTERIOR CONTINUOUS 6 MIL POLY OVER ENTIRE SIP ASSEMBLY SEE AIR BARRIER DETAIL (AB-2) 6 MIL POLY STRIP CAULKED TO OSB SEE AIR BARRIER DETAIL (AB-2) CONTINUOUS 6 MIL POLY RECOMMENDED 6 MIL POLY STRIPS & CAULKING EXTERIOR INTERIOR CAULKING SEE AIR BARRIER DETAIL (AB-2) OSB SEE AIR BARRIER DETAIL (AB-2) SIP TAPE CAULKING SIP TAPE VAPOUR BARRIER DETAILS FOR VAPOUR SEALING SIP CONNECTIONS NOVEMBER 2010 DWG. No. 1 VB-1

9 SIP SCREW ( SEE FASTENING TABLE) FOAM SEALANT VAPOUR SEALED AS PER VB-1 CHAMFER BLOCKING (WEDGE) OPTIONAL FURRING FOR ELECTRICAL PASSAGE INTERIOR FINISH RIDGE SECTION (WITH RIDGE BEAM) STRUCTURAL SUPPORT AS REQUIRED SIP SCREW (SEE FASTENING TABLE) ADJUST FRAMING MEMBER AS REQUIRED FOAM SEALANT VAPOUR SEALED AS PER VB-1 CAULK TO PANEL INTERIOR FINISH OPTIONAL FURRING FOR ELECTRICAL PASSAGE RIDGE SECTION (NO RIDGE BEAM) NOTE: FASTENING TABLE ON CONNECTION DESIGN (CD) SHEET OF ENGINEERED SHOP DRAWINGS ROOF RIDGE DETAILS FEBRUARY DWG. No. R-1

10 SIP SCREWS CAULK TO PANEL 6 MIL POLY VAPOUR BARRIER RIDGE SECTION (TYPICAL RIDGE BEAM) SIP SCREWS CAULK TO PANEL RAFTER & BEAM BY OTHERS FOR RAFTER & BEAMS (DESIGNED BY OTHERS) 6 MIL POLY NOTE: REFER TO AIR BARRIER (AB-2) AND VAPOUR BARRIER (VB-1) DETAILS FOR SEALING SIP CONNECTIONS NOTE: FASTENING TABLE ON CONNECTION DESIGN (CD) SHEET OF ENGINEERED SHOP DRAWINGS SECTIONS - ROOF RIDGE DETAILS FOR 12/12 PITCH ROOF FEBRUARY 2012 R-2 DWG. No. R-2

11 CHAMFER BLOCKING FOAM SEALANT SIP SCREW SIP SCREW VAPOUR SEALED AS PER VB-1 CAULK TO PANEL TOP PLATES RIDGE BEAM AS REQUIRED POST (BUILT-UP OR SOLID) PANEL JOINT WALL P ANEL RIDGE BEAM & POST POCKET NOTE: FASTENING TABLE ON CONNECTION DESIGN (CD) SHEET OF ENGINEERED SHOP DRAWINGS BEAM POCKET DETAIL DECEMBER DWG. No. R-3

12 FOAM SEALANT SIP SCREW CAULK TO PANEL VAPOUR SEALED AS PER VB-1 CHAMFER BLOCKING INTERIOR FINISH OPTIONAL FURRING FOR ELECTRICAL PASSAGE ROOF VALLEY STRUCTURAL SUPPORT AS REQUIRED SIP SCREWS SIP SCREW FOAM CHAMFER BLOCKING OPTIONAL FURRING FOR ELECTRICAL PASSAGE INTERIOR FINISH PANEL JOINT AT ROOF SUPPORT WEDGE OR BEAM CHAMFERED AT TOP INTERIOR FINISH PANEL CONTINUES OVER ROOF SUPPORT STRUCTURAL SUPPORT AS REQUIRED NOTE: FASTENING TABLE ON CONNECTION DESIGN (CD) SHEET OF ENGINEERED SHOP DRAWINGS ROOF VALLEY & INTERMEDIATE ROOF SUPPORT JANUARY DWG. No. R-4

13 CHAMFER BLOCKING (INSERT AFTER ROOF PANELS ARE IN PLACE) SIP SCREW SEE FASTENING TABLE CAULK TO PANEL FASCIA FOAM SEALANT VAPOUR SEALED AS PER VB-1 INTERIOR FINISH FOAM OPTIONAL FURRING FOR ELECTRICAL PASSAGE CAULK FOAM SEALANT FASCIA CAP & PLATE BLOCKING SOFFIT FRAMING OVERHANG (SEE TABLE R-T-3) WALL PANEL ROOF SUPPORT NOTE: FASTENING TABLE ON CONNECTION DESIGN (CD) SHEET OF ENGINEERED SHOP DRAWINGS EAVE DETAIL & ROOF SUPPORT AT EXTERIOR WALL FEBRUARY DWG. N o. R-5

14 SECTION A-A SEE FASTENING TABLE AND DETAIL BELOW EPS CORE OSB SKIN VAPOUR SEALED AS PER VB-1 A A SEE SECTION B BELOW SPLINE ROOF ASSEMBLY SECTION B SIP SPLINE BLIND FASCIA (SITE) FASCIA WEDGE FOR PLUMB CUT (SITE) NOTE: REFER TO AIR BARRIER (AB-2) AND VAPOUR BARRIER (VB-1) DETAILS FOR SEALING SIP CONNECTIONS. NOTE: FASTENING TABLE ON CONNECTION DESIGN (CD) SHEET OF ENGINEERED SHOP DRAWINGS TYPICAL SLOPED ROOF ASSEMBLY FEBRUARY DWG. No. R-6

15 SEE DETAIL R-1 OR R-2 A A SEE DETAIL R-4 OR R-5 BLIND FASCIA (SITE) FASCIA WEDGE FOR PLUMB CUT (SITE) ROOF ASSEMBLY SECTION A-A SIP SPLINE SIP SPLINE LUMBER SPLINE FOAM SEALANT OR CAULKING (SEE AB-1) NOTE: REFER TO AIR BARRIER (AB-2) AND VAPOUR BARRIER (VB-1) DETAILS FOR SEALING SIP CONNECTIONS. NOTE: FASTENING TABLE ON CONNECTION DESIGN (CD) SHEET OF ENGINEERED SHOP DRAWINGS SLOPED ROOF ASSEMBLY WITH RIDGE BEAM FEBRUARY DWG. No. R-7

16 A A INSTALL FASCIA BOARD ON SITE SPLINE SEE SECTION B BELOW EPS CORE SECTION A-A SEE FASTENING TABLE SECTION B ISOMETRIC ROOF ASSEMBLY GENERIC DETAIL FOR FLAT ROOF FOAM SEAL 3 FOAM CORE SPLINE OSB SKIN CAULK VAPOUR SEALED AS PER VB-1 VAPOUR SEALED AS PER VB-1 NOTE: REFER TO AIR BARRIER (AB-2) AND VAPOUR BARRIER (VB-1) DETAILS FOR SEALING SIP CONNECTIONS. NOTE: FASTENING TABLE ON CONNECTION DESIGN (CD) SHEET OF ENGINEERED SHOP DRAWINGS FLAT ROOF ASSEMBLY FEBRUARY DWG. No. R-8

17 ROOF JOISTS ATTACHED BY HANGERS OR SIDE NAILING OPTIONAL JOISTS OPTIONAL 1.5 RECESS TYPICAL U.N.O. 1.5 OR 3 RECESS SEE SKYLIGHT MANUFACTURER S DETAIL HANGER OR NAILS DOUBLE SPLINE JOIST SKYLIGHT OPENING & ASSEMBLY FEBRUARY DWG. No. R-9

18 FLASHING SECURE END PLATE REMOVE FOAM FROM ROOF PANEL AS TO INSTALL NAILER AND LEDGER BOARD TO MATCH WALL BOARD. LEDGER SECURED TO STUDS OPTION 1 FLASHING EMBEDDED MIN. 1" IN MASONRY SECURE TO NEW STUD WALL WITH SIP SCREWS WATER RESISTANT MEMBRANE NEW STUD WALL SECURED TO EXISTING STRUCTURAL WALL EXISTING WALL OPTION 2 NEW ROOF TO EXISTING WALL TYPICAL ROOF CONNECTION SECTIONS (ROOF TO WALL) DWG. No. FEBRUARY R-10

19 S (TWO SHOWN) ASPHALT SHINGLES NON-ADHERING BREATHABLE ROOFING UNDERLAYMENT INSTALLED AS PER MANUFACTURER S INSTRUCTIONS DRIP EDGE FASCIA COVER 2X_ FASCIA BOARD DRIP EDGE FASCIA BOARD FASCIA COVER FASCIA WEDGE FOR PLUMB CUT 2X_ BLIND FASCIA STARTER SHINGLE INSTALLED AS PER MANUFACTURER S INSTRUCTIONS METAL ROOFING OR CEDAR SHAKES S (TWO SHOWN) NON-ADHERING BREATHABLE ROOFING UNDERLAYMENT INSTALLED AS PER MANUFACTURER S INSTRUCTIONS DRIP EDGE FURRING INSTALLED AS PER MANUFACTURER S INSTRUCTIONS 2X_ FASCIA COVER FASCIA BOARD DRIP EDGE FASCIA BOARD FASCIA COVER FASCIA WEDGE FOR PLUMB CUT 2X_ BLIND FASCIA METAL ROOFING OR SHAKES INSTALLED AS PER MANUFACTURER S INSTRUCTIONS NOTE: VENTILATION OF SIP ROOF NOT REQUIRED. ROOFING APPLIED TO SLOPED SIPS DWG. No. AUGUST R-11

20 NON-ADHERED MEMBRANE (EPDM, PVC, TPO, ETC.) FASTENERS INTO OSB PROTECTIVE SHEATHING OR MEMBRANE AS REQUIRED OSB EPS ADHERED ROOFING MEMBRANE TORCHED ON OR GLUED ON ROOFING MEMBRANE FASTEN PROTECTIVE SHEATHING LAYER (OSB, PLYWOOD) WITH GLUE, NAILS OR SCREWS OSB EPS NOTES: SIP SURFACE TO BE DRY. INSTALL MEMBRANE ACCORDING TO MEMBRANE MANUFACTURER S DETAILS AND CONFORM TO REQUIREMENTS OF LOCAL BUILDING CODE. FLAT ROOFING APPLIED TO SIPS NOVEMBER 2011 DWG. No. R-12

21 * DRIVER BOX WIRING LED RECESS CEILING FIXTURE* STRAPPING INTERIOR FINISH * FIXTURE SPECIFICATIONS FIXTURE TO HAVE AMBIENT OPERATING TEMPERATURE +140F(+40C) MAXIMUM INSTALL AS PER MANUFACTURERS SPECIFICATIONS LED POT LIGHT INSTALLATION IN CEILING SIPS JANUARY 2017 DWG. No. R-13

22 UNFINISHED EAVE DETAIL FOR LEVEL SOFFIT RAFTER RECESS FOR INLAY FOAM SEALANT WALL PANEL VAPOUR SEALED AS PER VB-1 2 NAIL INTO TIMBERFRAME POST 1/2 DRYWALL CAULK TO PANEL FINISHED EAVE DETAIL WITH LEVEL SOFFIT RAFTER TAIL AND INLAY INSTALLED ON GROUND - SCREWED FROM TOP AND BOTTOM RAFTER 16" O/C RAFTER 1/2 " DRY WALL CAULK TO PANEL FINISHED FASCIA KICKER VAPOUR SEALED AS PER VB-1 INSULATION SUGGESTED POST FINISHED SOFFIT LEDGER WALL PANEL NOTE: REFER TO AIR BARRIER (AB-2) AND VAPOUR BARRIER (VB-1) DETAILS FOR SEALING SIP CONNECTIONS. ROOF OVERHANG EAVE DETAILS (TIMBERFRAME) 8020 DWG. No. FEBRUARY R-TF-1

23 HURRICANE STRAP OSB "TIE" CONVENTIONAL LADDER FOAM SEALANT BEAM / RAFTER VAPOUR SEALED AS PER VB-1 BUILT OUT OPTION POPULAR FOR ROOFS WITH COMMON RAFTER SYSTEMS AND PANEL ORIENTED VERTICALLY WALL PANEL NOTE: SCREW AND GLUE LADDER TO WALL PANEL FOAM HELD BACK FOR RAKE BLOCKING 2X_ INLAY RAKE BLOCKING FOAM SEALANT RAFTER / BEAM VAPOUR SEALED AS PER VB-1 RUN-BY OPTION, POPULAR FOR ROOFS WITH PRINCIPAL RAFTERS AND PURLINS AND PANELS ORIENTED HORIZONTALLY WALL PANEL NOTE: REFER TO AIR BARRIER (AB-2) AND VAPOUR BARRIER (VB-1) DETAILS FOR SEALING SIP CONNECTIONS. ROOF OVERHANG & RAKE (TIMBERFRAME) 8020 DWG. No. MAY R-TF-2