Installation Instructions

Transcription

1 sentry Railing Installation Instructions Manufactured by FHS-0001-LIT 1/13

2 Sentry Railing Installation Instructions Required Tools and Supplies: Sentry Top Rail Profile Sentry ottom Rail Profile Power Drill 1/8-in Drill it #2 Square Head it Protective Eye Wear Tape Measure Level Screw Driver, Phillips #2 Speed Square Miter Saw Pencil djustable Square Railing component list for each section: Post Sleeve Cap Top Rail racket Top Rail Post Sleeve Square alusters Post Sleeve Collar ottom Rail racket Crush lock ottom Rail Prior to installing railing: Please consult local zoning laws in regards to load requirements and bottom space requirements for rails. ll supporting structures must be in accordance with applicable building codes. Neighborhood associations and/or historic districts may regulate size, type, placement and ability of railing. pply for permits if required by local authorities and codes. Ensure compliance prior to installation. Local building code requirements will always supersede any and all suggested procedures and measurements in the following installation. The following installation instructions are intended as a general guideline based on common building practices used in railing installation. When railing span is greater than the distance between posts, trim both top and bottom rail ends to maintain uniform baluster spacing. Slide Post Sleeve Collar over each post prior to installing bottom rails and press securely into place. YES 2-in minimum from rail end to hole NO Rail Installation: Trim both ends of rail to maintain uniform baluster spacing. Ensuring trim mark does not create an open baluster mount hole at the bracket is critical; adjust accordingly noting uniform baluster spacing.

3 Maximum distance between posts: 6ft Rail = 72-in Sentry Top Rail racket Sentry ottom Rail racket 2 NOTE: Rail lengths will vary slightly due to manufacturing processes. Make sure rails are cut properly to correct length, and with hole pattern centered between posts before securing. NOTE: If using the post sleeve collar, make sure to position and glue collars in place prior to securing the bottom rail. Install 4x4 posts in the pre-determined 1 Using the supplied crush block and a level, position the bottom rail between the posts. Use a pencil or marker and locate the bracket fastener holes. 3 locations, cover with post sleeve and verify spacing. Posts should be plumb in both directions. If using post sleeve collar, slide collar over post sleeve prior to installing rails. fter carefully measuring between level and plumb posts, cut top and bottom guardrails to length. Slide bottom rail brackets over ends of bottom rail. Remove the guardrail and bracket and predrill all holes with 1/8-in bit (bracket shown in place for clarity). Replace the guardrail and bracket and secure with supplied 1 1/2-in screws. The most recent installation instuctions can be found our website. Please visit or call custmer service at Continued on next page

4 Sentry Rail Installation Instructions Complete bracket installation by inserting the plugs, being careful to align plugs with integrated fins. 5 Start the installation of the top rail by inserting the mounting brackets over the top rail. 7 Predrill all holes with a 1/8-in bit (bracket shown for clarity). Insert all remaining balusters into the bottom rail, then carefully lower the top rail and brackets into place. Secure both brackets using the supplied 1 1/2-in screws. 9 Complete the top rail installation by inserting the hole plugs, making sure to align plugs accordingly. 10 Fully insert the first baluster on each end of the secured bottom rail. If using round metal balusters, insert rail Inserts for round balusters into the top and bottom rail routed holes. Place round metal baluster through the inserts. (Round balusters must be a minimum of 32-in long). Lower the top rail and brackets over the balusters, making sure they fully insert into the top rail. Check for level, then locate and mark the screw holes on the posts. Complete the section by gluing the post cap in place.

5 Sentry Stair Installation Instructions NOTE: The slope of the stairs can be degrees (an 11-in run and a 7-in rise results in a 32 degree slope). Maximum length of rail for even aluster spacing between Post Sleeves: 6ft Rail: 66 1/4-in NOTE: When using the post sleeve collars, make sure to position and glue collars in place prior to securing the bottom rail. NOTE: Rail lengths will vary slightly due to manufacturing processes. Make sure rails are cut properly to correct length, and with hole pattern centered between posts before securing. Sentry Stair racket Top 1 Maximum inside distance between Post Sleeves: 6ft Rail = 56 3/16-in 2 Sentry Stair racket Top Install 4x4 posts in the pre-determined locations, cover with Post Sleeve and verify spacing. Posts should be plumb in both directions. 3 fter checking the posts for level and plumb, support the bottom rail alongside the two posts, making sure to center the baluster hole pattern equally between them. Lay a 2x4 or other continuous straight-edge over the nose of the stairs and supporting the bottom rail. Transfer the angles to the rails, and cut to correct length. Slide brackets over the bottom rail. Place the lower rail and brackets in place, and locate and mark the screw holes. Remove the rail and brackets, and predrill with 1/8-in bit. (bracket shown in place for clarity) Secure bottom rail using supplied 1 ½-in screws. Transfer the stair angle to balusters, and cut baluster ends to required length. C The most recent installation instuctions can be found our website. Please visit or call custmer service at Continued on next page

6 Sentry Stair Installation Instructions Slowly lower the top rail and brackets into position, making sure the baluster is fully seated onto the adapter. 6 Place all remaining inserts, then balusters, onto the bottom rail holes. Place inserts into top rail, and carefully lower and align with balusters making sure to fully seat each. Secure the top brackets with supplied 1 ½-in screws. C lign bottom and top rails to transfer the proper angle, then cut to proper length. It is critical that all balusters are the same length and angle for best appearance. Insert the square baluster stair Insert or round baluster stair insert into the top and bottom rail holes, making sure to align them properly. Locate and mark bracket holes, and predrill with 1/8-in bit. (racket shown in place for clarity)

7 8 lign plugs with holes, and press in place making sure to align the fins. 9 Complete the section by gluing the post caps and crush block with quality exterior adhesive. The most recent installation instuctions can be found our website. Please visit or call custmer service at

8 Design Grid