Easy2Build TM. 6 x 8 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions

Transcription

1 EasyBuild TM Smart Tech solutions 6 x 8 Easy-Grow Greenhouse Assembly Instructions 0 S tr uct ure 7 PC SHELL Systems Trading Corporation 50 7th Avenue Suite 809, New York, NY 03 Customer Service: (877) ext customerservice@stcaustin.com

2

3 Introduction Thank you for purchasing your EasyBuild TM 6x8 Easy-Grow Greenhouse. When properly assembled and maintained, this greenhouse will provide years of enjoyment. These instructions include helpful hints and important information needed to safely assemble and properly maintain the greenhouse. Please carefully read these instructions completely before you begin. This greenhouse has been designed with patented technology to be easily assembled. All but one step can be completed by one person. You will need assistance from another person to attach the roof. Although the greenhouse can be assmebled in six to eight hours, we recommend to take your time and make it a weekend project. Before Starting Assembly: CAREFULLY READ ALL INSTRUCTIONS BEFORE YOU BEGIN AND FOLLOW THE STEPS IN THE ORDER THEY ARE PRESENTED.. Make sure you have all the necessary parts: Compare the contents of the two cartons to the List of Parts. If any parts are missing or damaged or you have any questions, please contact customer service by phone at (877) ext: or by at customerservice@stcaustin.com before beginning assembly.. Lay the parts out in separate staging areas: The List of Parts has the corresponding step number referenced to each part. We recommend that while you go through the list, make staging areas for each step and place the parts necessary for each step in these areas. This will save you time and effort during assembly 3. Select a Location: When selecting a site for your greenhouse, a flat level area is essential and if possible, with proper water drainage and easy access to power and water necessary for greenhouse gardening. Choose a sunny, level position away from overhanging trees and power lines and protected from the wind as much as possible. The location should be away from structures that could cause snow to drift on or around the greenhouse. Locate underground pipes or cables before preparing the site or anchoring the greenhouse. Note: You may assemble the greenhouse on a hard level surface and move it to its final position when finished. Make sure there are no obstacles between the assembly area and the final position.. Prepare a Foundation: After choosing a location, proper preparation of the site is essential. The site must be level. If the site is not level, create a base slightly larger than the outside dimensions of the greenhouse using a perimeter of two by fours filled with either soil, sod or gravel. Make sure the base is square by measuring the diagonals from both sides and making sure they are equal. The greenhouse is secured from the inside with pegs into holes cast with concrete. See step6 for details. If you decide to have a concrete base it is best to contact a reliable contractor to ensure it is flat and level. Make sure you have checked with your local authorities regarding any required building permits. 5. Make sure you have the proper tools: Tape Measure Work Gloves Safety Goggles Phillips Screwdriver Spirit Level Small Step Ladder Wooden Mallet Liquid Soap or WD0 Lubricant Scissors Hex Key (included) NOTE: A cordless drill with Phillips head bit is highly recommended but not essential. of 5

4 Safety Advice The greenhouse must be positioned and fixed on a flat level surface. Dispose of all plastic bags safely. Keep them out of the reach of small children. Keep children and pets away from the assembly area until the work is completed. Always wear shoes, gloves and safety goggles when working. In manufacturing all sharp edges and burs have been removed but caution should still be taken when handling metal parts. Do not lean against or push the greenhouse during assembly. Take special care not to touch overhead power lines with the aluminium profiles. Do not attempt to assemble the greenhouse in windy or wet conditions. Do not position your greenhouse in an area exposed to excessive wind. If using power tools or a step ladder always follow the manufacturers safety instructions. Hot items such as recently used grills, blowtorches etc. must not be stored in the greenhouse. Store the polycarbonate panels in a cool dark place like a garage until you are ready to use them. Make sure the greenhouse complies with local building codes. Table of Contents Introduction... Safety Advice... General Order of Assembly... List of Parts... 3 Assemble Back... 6 Assemble Door... Assemble Front... 7 Assemble Sides... 5 Prepare Shelves Connect Sides to Back... 3 Connect Sides to Front Assemble and Connect Gables Brace Sides... 0 Assemble and Install Roof Vent... Install Circular Vent... Install Side and Roof Panels... 5 Install Weather Stripping... 6 Install Trim Plates... 8 Weather Strip and Hang Door... 9 Secure to Ground Install Trays and Bin Holder... 5 General Order of Assembly Step : Assemble Back Step : Assemble Door Step 3: Assemble Front Step : Assemble Sides Step 5: Prepare Shelves Step 6: Connect Sides to Back Step 7: Connect Sides to Front Step 8: Assemble and Connect Gables Step 9: Brace Sides Step 0: Assemble and Install Roof Vent Step : Install Circular Vent Step : Install Side and Roof Panels Step 3: Weather Stripping Step : Install Trim Plates Step 5: Weather Strip and Hang Door Step 6: Secure to Ground Step 7: Install Trays and Bin Holder of 5

5 List of Parts The greenhouse is shipped in two cartons. These cartons are heavy. Be careful when lifting them. Wear proper safety gear including work shoes, gloves and goggles. The parts are identified by removable stickers. Place all the parts for each step in staging areas, checking that you have all parts as you go. If any parts are missing or damaged, contact STC customer service before beginning assembly: Customer Service: (877) ext. or L0A Step 3 L06A Step 3 L0B Step L06B Step 3 L0C Step L06C Step 3 L0A L0B Steps,3 Steps,3 L0C L0D L0E L0F L0G Step Step Step 3 Step 3 Step 8 L03A L03B Step Step L03C L03D Step Step L03E L03F L03G 3 Step 8 Step 8 Step 8 L03H Step 8 L0A Step 3 L0B Step L0C L0D L0E Step Step Step 7 L0F Step L07A Step L07B Step L08A Step 8 L0A Step 0 LA Step 0 LA Step 0 L3A Step L3B Step L3C Step L05A Step LA Step 5 L05D L05B L05C L05D L05E Step Step 3 Step 0 Step LB Step 5 LC Step 5 LD Step 5 3 of 5

6 Panel Y Step S03 Step Y Step S0 Steps,3 Y3 Step Y Step S05 Steps,3 Y5 Step 3 S09 Steps,3 Y6 Step 3 S0 Steps,3 Y7 Step 3 Y8 Step 3 S Step Y9 Step S8 Step 3 Y0 Step S9 Step Y Step Y 3 Step S Step 8 Y3 Step S8 6 Steps,3 Y Step 0 Y5 Step S39 Step of 5

7 Trim Plate Bracing Parts L09A Step L09B Step S06 S07 S6 Steps,3,9 8 Step 9 Steps,3 J0L Step Hex Key Steps,3,9 J0R Step J03 Step S3 3 Step 8 rubber stripping J0 Step J0 63M Steps 3,5 L5A Step Vent Shelf Trays circular vent Step J05 0 Step 7 vent frame Step Door Handle plastic nut Step S0 6 Steps,3, Roof Vent Handle S9 S30 S3 S3 S33 Step Step Step Step Step S08 S 6 Steps, Step Anchor Clip and Peg S5 Step 0 S7L Step 3 S3 6 Step 6 S35 6 Step 6 S7R Step 3 S0 S3 9 Steps,,3,,8 Steps,,0 S0 Step S S 9 Steps,,0 Step 0 S Step 8 SA Step 0 S6 S36 Step 0 Step 7 S37 Steps 5,6 5 of 5

8 Assemble Back Lay out all the parts for the back face in a staging area. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The back is assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE..A Slide short side of connector S0 into channels of profiles L0A and L0B. Line up last hole on connector S0 with hole in each profile. IMPORTANT: The holes are not at the midpoint of the profile. Arrange profile so the 8 portion will be the bottom when standing..b Secure with S0 screws. L0A L0B S0 8 (7 mm).a Line up bottom hole on short side of connectors S0 with hole on side of profiles L03C and L03D. S0 L03C L03D.B Secure each S0 connector with two S0 screws. S0 S0 8 (7 mm) NOTE: ALL VIEWS ARE FROM INSIDE. #L0A #L0B #L03C #L03D #S0 #S0 6 6 of 5

9 .3A Attach profiles L0B and L03C to profile L0F by sliding the long sides of connector S0 into channels lining up last hole in S0 with holes in profile L0F. Attach profiles L03D and L0A to profile L0F by sliding the long side of connector S0 into profile channels lining up last hole of S0 with holes in L0A. L0B L03C L03D L0F L0A L0F.3B Secure with four S0 screws. L03C L03D L0B L0F L0A L0F NOTE: ALL VIEWS ARE FROM INSIDE. Screw #L0F #S0 7 of 5

10 .A Slide connectors S08 into channels of profiles L03C and L03D..B Secure with four S0 screws. L0B L03C L03D S0 L0A S08 NOTE: ALL VIEWS ARE FROM INSIDE. S08 S08 #S0 #S08.5 Slide connectors S0 and S0 into profile L0B until they securely click into place. S0 s S0 and S05 CLICK into place. S05 S0 L0B L0B L0B S05 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #L0B #S0 #S05 8 of 5

11 .6A Carefully line up connector S0 with profile L0B and connector S05 with profile L0A. Slide profile L0B half way into place. Continue sliding until connectors S0 and S05 click securely into profiles. NOTE: ALL VIEWS ARE FROM INSIDE. L0B.6B Line up holes on connectors S08 with holes in profile L0B and secure with four S0 screws. L03C L03D L0A L0B S0 S0 s S0 and S05 CLICK into place. L0B S05 Screw There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #S0.7A Slide hex bolt S3 into channels of profiles L05A and L05B as shown..7b Screw hex nut S onto bolt. Do not completely tighten. L05A L05B S L05A S3 L05B #L05A #L05B Bolt/Nut #S3 #S 9 of 5

12 .8A Remove protective plastic from both sides of panels Y, Y, Y3 and Y. Place side to face toward the sun facing down. Fit panels Y and Y into bottom channel of profiles L05A and L05B. Remove protective plastic from EACH side of poly carbonate L05A panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. L05B Y L05A Y NOTE: ALL VIEWS ARE FROM INSIDE. Y.8B Slide panels into V-channels on profiles L0A, L0B, L03C and L03D..8C Slide panels Y3 and Y into V-channels on profiles L0A, L0B, L03C and L03D. Fit inside channels on profiles L05A and L05B. Y Y Y Y Y3 L05A Y L0B L03C Y L05B Y L05A L03D L0A Y Panel Panel #Y #Y3 #Y #Y 0 of 5

13 .9 Slide hex nut S and hex bolts S3 into U-cutout in both sides of profiles L03C and L03D. Tighten securely to hold in place. L05A L05B L05A L03C L03D NOTE: ALL VIEWS ARE FROM INSIDE..0A Slide profiles L0C and L0D into connectors S09, S0 and S until they click into place. s S09, S0 and S CLICK into place. S L0C S L0C L0D S09 L0C L0D L0D.5 (63 mm) S0 S09.5 (63 mm) IMPORTANT: The holes are not at the midpoint of the profiles. Arrange profile so the.5 portion will be the bottom when standing. S0 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #L0C #L0D #S09 #S0 #S of 5

14 .0B Slide connectors S09 and S0 half way into profiles L0A and L0B. Continue sliding together making sure panels Y3 and Y fit into V-channels of profiles L0C and L0D. s click securely into profiles. L0C L0D s S09 and S0 CLICK into place. S09 Y Y3 Y S0 S09 L0B L0A L0B S0 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. L0A.A Place connectors S onto profiles L0C and L03C and L0D and L03C matching up all holes. L0C L03C L03D L0D S.B Screw S0 screws partially into bottom two holes. Do not tighten..c Screw S0 screws into top two holes. Tighten all screws. Repeat for both sides. S0 S0 S0 S0 NOTE: ALL VIEWS ARE FROM INSIDE. #S0 #S 8 of 5

15 .A Insert long side of cable connector S06 into profile channel L0B with hook facing up. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. NOTE: ALL VIEWS ARE FROM INSIDE. Y L0B L0F Y L0F L0A L0B.B Attach one side of short cable S6 to hook and lace under profile L0F. Attach other side of cable to another S06 cable connector. With hook facing the center, insert connector into profile channel L0B and push towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. IMPORTANT: Make sure all corners are squared at 90 degrees..3 Repeat step. inserting cable connectors S06 into profiles L0A and L0B. Cable rests next to panel Y and behind profile L0F. Slide connector until profile corners are square and cable is tight. Securely tighten second connector to hold in place. Hex Key Cable Cable #S06 #S6 3 of 5

16 Assemble Door Lay out all the parts for the door in a staging area. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The door is assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE..A Slide three hex bolts S3 into channel of profile L05E. L05E.B Screw two S hex nuts onto bolt on each end. Do not completely tighten. L05E S3 S. Remove protective plastic from both sides of panels Y5. Place side to face toward the sun facing down. Fit panels into channels of profile L05E. Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. Y5 L05E Y5 L05E NOTE: ALL VIEWS ARE FROM INSIDE. #L05E Bolt/Nut #S3 #S 3 Panel #Y5 of 5

17 .3 Place door profiles L3A, L3B and L3C next to connectors S8 around Y5 panels as shown. Slide connectors into profiles. Make sure panels and profile L05E fit into V-channels of each profile. S8 connectors will be secured to profiles in Step. S8 L3A S8 L3B Y5 S8 L3C Y5 S8.A NOTE: ALL VIEWS ARE FROM INSIDE. Slide hex nuts and bolts into U-cutout in side of profiles L3B and L3C. Tighten securely to hold in place. S8 L3A NOTE: The holes at the top of profile L3B and the bottom left corner of profile L3A will be secured in Step.5..B Secure connectors with six S0 screws. L3A L3B L3A L3B Y5 L3C Y5 L3C L3A L3A #L3A #L3B #L3C Screw #S0 6 #S8 5 of 5

18 .5 Place brace L5A onto door lining up the holes on each end with the holes in profiles L3A and L3B. Slide hex bolt so it fits through hole in brace. Secure brace with two S0 screws and S hex nut. S L3A L3B L5A L3C L3A IMPORTANT: The hole for hex bolt is not at the midpoint of brace. Turn brace until all holes line up. Brace will dip slightly when hex bolt is secured. NOTE: ALL VIEWS ARE FROM INSIDE. Brace #L5A Screw/Nut #S0 #S.6A Open door handle kit and remove parts. Slide pin S9 through handle S30, washer S3and hole in profile L3C into washer S3. S9 S30.6B Slide washer S3 into groove on pin S9 to hold securely in place. L3C S3 S3 L3C S3.6C Hook one side of spring S33 into hole on handle S30. Hook the other side into pin hole on profile L3C. NOTE: s packaged as Door Handle Kit. S33 #S9 #S3 #S3 L3C #S30 #S33 6 of 5

19 Assemble Front Lay out all the parts for the front face in a staging area. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The front is assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE. 3.A Lay out profiles L0A, L0B, L06A and L06B so all holes line up. Slide short side of connector S0 into channels of profiles L0A, L0B, L06A and L06B. IMPORTANT: The holes are not at the midpoint of the profile. Arrange profile so the 8 portion will be the bottom when standing. L06B L06A S0 S0 L0A L0B L0A L06A S0 S0 8 (7 mm) 8 (7 mm) L0B L06B 3.B Line up lower hole on connector S0 with hole in each profile and secure with S0 screws. NOTE: ALL VIEWS ARE FROM INSIDE. L06B L06A L0A L0B #L0A #L0B #L06A #L06B #S0 #S0 7 of 5

20 3.A Slide profiles L06C into L06A and L06B using connectors S8. S8 connectors do not snap into place. S8 L06C S8 S8 3.B Place connectors S7L and S7R on corners matching up bottom two holes with holes in profiles L06A, L06B and L06C as shown. S7L S7L L06C L06B L06A L06B S7R S7R L06B L06A L06A 3.C Secure each connector with two S0 screws. S7L S7R S0 S0 #L06C #S8 #S7L #S7R 3.3A Attach profiles L0B and L06B to profile L0A. Slide long sides of connectors S0 into channels of profile L0A, lining up last hole in S0 with holes in profile L0A. Attach profiles L06A and L0A to profile L0A. Slides long side of connectors S0 into channels of profiles L0A, lining up last hole of S0 with holes in L0A. 3.3B Secure with four S0 screws. L0B L06B L06A L06B L0A L0B L0A L06A L0A L0A L0A L0A NOTE: ALL VIEWS ARE FROM INSIDE. #L0A Screw #S0 8 of 5

21 3.A Slide profiles L0E and L0F into connectors S09, S8 and S0 until they click into place. L0F S8 S8 L0F L0E S09 s S09, S0 and S8 CLICK into place. S09 L0F 6.5 (676 mm) L0E L0E 6.5 (676 mm) S0 S0 IMPORTANT: The holes are not at the midpoint of the profiles. Arrange profile so the 6.5 portion will be the bottom when standing. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #L0E #L0F #S09 #S0 #S8 3.B Remove protective plastic from both sides of panel Y8. Place side to face toward the sun facing down. Fit panel into V-channel on profile L06. Y8 Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. L06C Y8 L06C NOTE: ALL VIEWS ARE FROM INSIDE. Panel #Y8 9 of 5

22 3.5A Slide connectors S09 and S0 half way into profiles L0A and L0B. Continue sliding together making sure panel Y8 fits into V-channels of profiles L0F and L0E. s click securely into profiles. s S09 and S0 CLICK into place. L0F L0E S09 Y8 S0 S09 L0B S0 L0B L0A L0A There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 3.5B Place connectors S7L and S7R on frame, lining up holes as shown. L0F L0E 3.5C Secure with two S0 screws. S7L S7R S0 S0 L06B L06A NOTE: ALL VIEWS ARE FROM INSIDE. Screw #S0 0 of 5

23 3.6A Remove protective plastic from both sides of panels Y5, Y6 and Y7. Place side to face toward the sun facing the down. Fit panels Y7 into top channels of L05C. Y6 IMPORTANT: Make sure to assemble a right and left side. L05C Y7 Y7 L05C L05C Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. NOTE: ALL VIEWS ARE FROM INSIDE. Y8 3.6B Slide Y6 panels into V-channels on profiles L0A, L0B, L06A and L06B. Note Y7 panel sits next to panel Y8. L06B L06A Y8 L0B L0A Y7 Y7 Y7 3.6C Slide Y5 and Y6 panels into V-channels on profiles L0A, L0B, L06A and L06B. Fit inside channels on L05C profiles. Y7 L05C Y8 L05C L05C Y7 L05C L0B L06B L06A L0A Y6 Y5 Panel Panel Panel #L05C #Y6 #Y5 #Y7 of 5

24 3.7A S0 Slide short side of connectors S0 into channel of profile L0A. Line up last hole on connector with holes on profile. NOTE: ALL VIEWS ARE FROM INSIDE. 3.7B Secure with S0 screws. L0A S0 S0 S0 #L0A #S0 #S0 3.7C Slide connectors S0 and S05 into profile L0A until they click into place. S0 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S0 S05 s S0 and S05 CLICK into place. S05 #S0 #S05 of 5

25 3.8A As you slide bottom profile L0A half way into place, carefully line up S0 connectors with channels on profiles L06B and L06A and S0 and S05 connectors with profiles L0B and L0A. Continue sliding, making sure panels Y6 and Y5 fit into V-channels. Snap connectors S0 and S05 securely into profiles. L06A L0A L0B L0A s S0 and S05 CLICK into place. L06B L06A L06A Y6 Y5 L0A S0 S0 S0 S05 L0A S05 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 3.8B Secure S0 connector to profiles L06A and L06B with S0 screws. L06A NOTE: ALL VIEWS ARE FROM INSIDE. L0A Screw #S0 3 of 5

26 3.9A Insert long side of cable connector S06 at an angle into profile channel L0B with hook facing up. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. NOTE: ALL VIEWS ARE FROM INSIDE. L06A L06B Y5 L0A Y6 L0B L0A 3.9B Attach one side of short cable S6 to hook and lace under profile L0A. Attach other side of cable to another S06 cable connector. With hook facing the center, insert connector into profile channel L0A and push towards center until profile corners are square and cable is tight. 3.9C Use hex key to securely tighten and hold in place. IMPORTANT: Make sure all corners are squared at 90 degrees. 3.0 Repeat step 3.0 inserting cable connectors S06 into profiles L0A and L0A. Cable rests next to panel Y5, under profile L0A and over vent. Slide connector until profile corners are square and cable is tight. Securely tighten second connector to hold in place. Hex Key Cable Cable #S06 #S6 of 5

27 Assemble Sides Lay out all the parts for the sides in a staging area. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. You are assembling both sides in the following steps. Both sides are identical until step 6..A S0 Line up the four profiles L03B so the holes are at the same position. Slide long side of connectors S0 and S08 into channel of profile, lining up holes as shown. Repeat for all four L03B profiles. S0 L03B.B Secure with three S0 screws. S0 S0 L03B S08 S08 #L03B #S0 #S0 #S0 #S08 8.A Place L03B onto profiles L07A and L0C. Line up holes as shown. L07A.B Secure with three S0 screws. L07A Repeat to make two sets. L07A L03B L03B S0 L0C S0 L0C Screw L0C #L0C #L07A #S0 6 5 of 5

28 .3A Place L03B onto profiles L07B and L0C. Line up holes as shown. L07B.3B Secure with three S0 screws. Repeat to make two sets. L07B L07B S0 L03B L03B S0 S0 L0C L0C S0 L0C Screw #L0C #L07B #S0 6.A Lay out profiles L03A so the holes are at the same position. Slide short side of connectors S0 into channel of profile until the last hole in S0 lines up with the bottom hole on profile L03A. L03A S0 IMPORTANT: The holes are not at the midpoint of the profile. Arrange profile so the 8 portion will be the bottom when standing..b Slide another connector S0 so it lines up with the middle hole on profile L03A. S0.C Secure all pieces with S0 screws. Repeat to make two sets. L03A L03A L03A S0 S0 8 (75 mm) 6 / (65 mm) #L03A #S0 #S0 6 of 5

29 .5A Lay out profiles L0D so the holes are at the same position. Slide short side of connector S0 into channel of profile, lining the last hole in S0 with the hole on profile L0D. Secure with S0 screw. S0.5B Slide connector S39 into profile L0D until it snaps into place. Repeat to make two sets. S39 S39 CLICKS into place. L0D L0D S39 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S0 #L0D #S0 #S0 #S39.6 Slide connector S03 into profile L0B until it clicks into place. S03 S03 S03 CLICKS into place. L0B #L0B #S03.7A Attach profiles L0B and L0C to profile L03A by sliding the long sides of connectors S0 into the channels. The last hole of connector S0 lines up with the holes in the profiles..7b Secure with two S0 screws. Repeat to make two sets. L03A IMPORTANT: S03 rests on top of connector S0. S0 screw secures S03 to profile L0B. L0B S0 L0B L0C S0 S03 L03A S0 S0 L0C #L0C Screw #S0 7 of 5

30 .8A Connect profile L0D by sliding connector S39 into profile L0B until it clicks securely into place. Slide connector S0 into channel of L0C..8B Secure with S0 screw. Repeat to s S39 CLICKS into place. make two sets. S39 L03A L0B S39 L0C Screw L0D S0 #S0 S0 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves..9 Slide connectors S9 and S03 into profile L03A until they click securely into place. Repeat to make two sets. S9 S9 s S03 and S9 CLICK into place. L03A S03 NOTE: ALL VIEWS ARE FROM INSIDE. S03 #S03 #S9 8 of 5

31 .0 Slide sections together as shown. Repeat to make two sets. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. s S03 and S9 CLICK into place. L07A S9 L07B L07B S9 L07A L03A L0C S03 L0C NOTE: ALL VIEWS ARE FROM INSIDE. L0C S03 L0C NOTE: The two sides are identical. When you connect them to the back, there will be a right and left side. Stand these up. 9 of 5

32 Prepare Shelves Place all the parts for the shelves on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. 5.A Line up the shelf profiles so the holes are at the same position. Slide long side of connector S37 into channel of each profile, lining up the last hole on the connector with the hole in the channel. LB S37 LC LD S37 LA IMPORTANT: The shelf profiles have rectangular holes in the channel or side of one end. Slide connector S37 into other side, lining up last hole in connector with hole in the channel. 5.B Secure with S0 screw. S37 S0 #LA #LB #LC #LD #S37 #S of 5

33 Connect Sides to Back With the outside facing a wall, carefully stand back up and lean against the wall. Stand each side up and place next to the back. Both sides are identical until the shelf profiles are connected. Make certain that positions of profiles L07A and L07B match the diagrams before connecting. 6.A Set up one side faaing inside with L07B next to the back. Slide shelf profile LB into connector S03 until it clicks into place. Slide shelf profile LD into connector S39 until it clicks into place. L07B LB LB S03 LD L07A LD S03 S39 S39 s S03 and S39 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 6.B Carefully slide left side into back, lining up connectors with profiles. Move side so connectors S09 and S0 are half way into profiles L07B and L0C. s S37 rest on top of profile L0F. Push side in until connectors click into place. S37 L0F L07B S09 S09 S37 L07B LB LD S37 L0F S37 Secure connectors S37 to profile L0F with two S0 screws. S0 L0F S0 S0 L0C s S0 and S09 CLICK into place. L0C S0 VIEWS FROM INSIDE. Screw #S0 3 of 5

34 6.A Set up the other side facing inside with profile L07A next to back. Slide shelf profile LA into connector S03 until it clicks into place. Slide shelf profile LC into connector S39 until it clicks into place. L07A s S03 and S39 CLICK into place. LA LE LC LC S03 S39 S03 S39 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 6.B Carefully slide right side into back, lining connectors up with profiles. Move side so connectors S0 and S05 are half way into profiles L07A and L0C. s S37 rest on top of profile L0F. Push side in until connectors click into place. S0 CLICKS into place. S0 S0 L07A L07A L0F S37 L0F S37 LC LA Secure connectors S37 to profile L0F with S0 screws. S05 S0 L0C S0 L0F S05 VIEWS FROM INSIDE. L0C S05 CLICKS into place. Screw #S0 3 of 5

35 Connect Sides to Front Keep the structure as is, with the back against the wall until you finish this step. This will make it easier to keep the angles square. 7. Slide shelf profile LA into connector S03 on the left side until it clicks into place. Slide shelf profile LB into connector S03 on the right side until it clicks into place. s S03 CLICK into place. S03 LA L07A S03 LA L07B S03 LB S03 s S38 CLICK into place. LB There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 33 of 5

36 7.A Lift front from inside and rest it next to sides. Line up connector S0 with profile L07A, connector S09 with profile L07B and connectors S0 and S05 with profiles L0C. S0 L07A S09 LA L07B LB S05 L0C S0 L0C 7.B Carefully pull the front until all connectors are half way inside each profile. Make sure connector S37 attached to shelf profiles rest on top of profile L0A. Push front into sides until connectors click into place. S09 s S09 and S0 CLICK into place. S37 L07B S0 L07A S37 L0A S09 LA L07B S37 S05 S0 LB L0C S0 L0C s S0 and S05 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 3 of 5

37 7.3A Slide shelf profile LC at a slight angle so one end slides half way into connector S39 and the other side with connector S37 rests on top of profile L0A. Continue to slide until profile clicks into connector S39. S39 CLICKS into place. LC S39 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 7.3B Repeat step 7.3A, sliding shelf profile LH into S39 connector. Make sure connector S37 rests on top of profile L0A. L07A S39 CLICKS into place. LD S37 L0A LA S39 LC S39 7.3C Secure S37 connectors to L0A profiles with four S0 screws. L0A LD L0A LA LB LC Screw VIEWS FROM INSIDE. #S0 35 of 5

38 Assemble and Connect Gables Lay out all the parts for the gables in a staging area. Make sure the pieces are in the correct positions before assembling. Please carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including shoes, gloves and goggles. 8.A Slide connector S into channels of profiles L03E. Slide another S connector into channels of profiles L03E and L03F. IMPORTANT: U-shaped cutout is not at midpoint of S profile L03F. Attach longer side (.5 ) to connector S. L03E L03E S 8.B Secure each set with four S0 screws. L03E L03E S L03E L03F L03E L03F L03F S0 #L03E #L03F 3 #S0 #S 8 8.A Slide connector S into profiles L03H and L03G until it clicks securely into place. IMPORTANT: U-shaped cutout is not at midpoint of profile L03G. Attach longer side (.5 ) to connector S. Make sure coonector S is positioned correctly before connecting. s S CLICKS into place. S 8.B Line up holes on bracing bar S3 with holes in profiles L03G and L03H. S3 L03H S L03G L03G L03H L03G 8.C Secure brace to profiles with two S0 screws. L03G L03H L03G L03H There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S0 #L03G #L03H #S Screw #S0 Brace #S3 36 of 5

39 8.3 From the inside of the greenhouse, use two people to carefully lower center gable onto frame. Line up and slide profiles L03G and L03H into connectors S9 until they click securely into place. L03H L03H L03G S9 S9 S9 s S9 CLICK into place. L03G S9 L03G There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. NOTE: U-shaped cutouts on profile L03G faces back. 8. From the inside of the greenhouse, use two people to carefully lower front and back gables onto frame. Line up and slide connectors S0 into channels of profiles L03E and L03F. L03E L03E L03E NOTE: U-shaped cutouts on profile L03F faces front. S0 S0 L03E S0 S0 L03F S0 L03F L03F S0 37 of 5

40 8.5 Line up profiles L08A and L0G as shown. Note that L08A has a cutout on one end. The plain side slides into V-channels of profile L0G. Note the rectangular holes in the channels of profile L0G are NOT on the side next to the V-channel. L08A L08A L08A L08A L0G L0G IMPORTANT: There is one correct way to connect these profiles. Arrange profiles before sliding together. Use WD0 or liquid soap if parts do not easily slde together #L0G L0G #L08A 8.6A Using a small step ladder inside the greenhouse, carefully slide profiles L08A and L0G into back connector S at a slight angle. Gently push center gable slightly towards the front to slide other end of profile into connector S. Make sure both connectors snap securely into place. Note L0G profile rests on top of connector S. IMPORTANT: Make sure profiles L0G with L08B are in correct positions before installing. Arrange profile L0G so rectangular holes in channels face the LEFT when looking at the front of the greenhouse from the outside. S L0G L08B S s S and S CLICK into place. S 8.6B Slide profile L0G at a slight angle into center gable connector S. Gently push front side slightly forward to slide other end of profile into connecor S8. Make sure both connectors click securely into place. Note profile L0G rests on top of connector S. IMPORTANT: Arrange profile L0G so rectangular holes in channels face the LEFT when looking at the front of the greenhouse from the outside. S L0G S S8 s S and S8 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #L0G 38 of 5

41 8.7A L03E From inside of greenhouse secure S0 connectors to profiles L03E and L03F with two S0 screws. 8.7B Secure S connectors to profiles L0G with one S0 screw. L0G S0 S0 S L03F S0 S0 S0 VIEWS FROM INSIDE. Screw VIEWS FROM INSIDE. #S A From inside of greenhouse, line up bracing bar S3 with holes in profiles L03A and L03H. Secure one S0 screw partially into each end. Then go back and tighten both screws. L03H S0 8.8B Line up bracing bar S3 withholes in profiles L03A and L03G. Secure one S0 screw partially into each end. Tighten both screws. L03H L03G S3 S0 S3 L03A S3 L03G S0 L03A L03A S3 VIEWS FROM INSIDE. S0 L03A VIEWS FROM INSIDE. Screw Brace #S0 #S3 39 of 5

42 Brace Sides Place all the parts for bracing the sides on a level surface. Make sure the pieces are in the correct positions before assembling. Please carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including shoes, gloves and goggles. 9.A From the inside of the greenhouse, insert long side of cable connector S06 into profile channel L07B with hook facing the front. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. L07B L07B L0B L0B LA L03A IMPORTANT: Make sure all corners are squared at 90 degrees. L0C 9.B Attach one side of long cable S07 to hook and lace behind profile LA. Attach other side of cable to a second S06 cable connector. With hook facing the back, insert connector into profile channel L0C. L03A 9.C Push towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. L0C VIEWS FROM INSIDE. L0C L03A IMPORTANT: Make sure all corners are squared at 90 degrees. 9. Repeat step 9. inserting cable connectors S06 into profile L07B with hook facing the back and into profile L0C with hook facing the front. Cable rests behind profile LA. Slide connector until profile corners are square and cable is tight. Securely tighten second connector to hold in place. L07B VIEWS FROM INSIDE. L0B L07B L03A L0B LA L03A L0C IMPORTANT: Make sure all corners are squared at 90 degrees. L0C Hex Key Cable #S06 Cable #S07 0 of 5

43 9.3A From the inside of the greenhouse, insert long side of cable connector S06 into channel of profile L07A with hook facing the back. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. L07A L07A L0A L0A LB L03A 9.3B L03A Attach one side of long cable S07 to hook and lace behind profile LB. Attach other side of cable to a second S06 cable connector. With hook facing the front, insert connector into channel of profile L0C. 9.3C Push towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. L0C L03A L0C IMPORTANT: Make sure all corners are squared at 90 degrees. VIEWS FROM INSIDE. L0C 9. Repeat step 9.3 inserting cable connectors S06 into profile L0C with hook facing the front and into profile L07A with hook facing back. Cable rests behind profile LA. Slide connector until profile corners are square and cable is tight. Use hex key to securely tighten second connector to hold in place. L07A L0A 9.5 L03A VIEWS FROM INSIDE. L0C Repeat step 9. through 9. on the other side of the greenhouse. LB L07A L0A L0C L0B L07B L07A IMPORTANT: Make sure all corners are squared at 90 degrees. LB LA L0A L0C L0C Hex Key Cable #S06 Cable #S07 8 of 5

44 Assemble and Install Roof Vent 0. Lay out all the parts for the roof vent in a staging area. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The roof vent is assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE. LA Remove protective plastic from both sides of panel Y. Place side to face toward the sun facing up. Fit panel into channels of profiles L0A and LA. Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING UP. Y L0A L0A NOTE: ALL VIEWS ARE FROM INSIDE. Panel LA #L0A #LA #Y 0.A LA Fit panel and profiles L0A and LA into channels of profiles LA. Make sure holes in ends of profiles line up. 0.B Secure with four S6 screws. LA S6 LA Y LA LA LA L0A LA S6 LA S6 LA Y S6 L0A S6 0.3 Attach handle S5 to profile L0A with two S screws. S5 LA LA S6 L0A Y S S S5 S L0A S IMPORTANT: hollow side of handle S5 faces down when attached. L0A Handle #LA #S5 Screw #S #S6 of 5

45 0.A With pins facing up on the inside of the greenhouse, slide one end of profile L05D into V-channel of profile L03F. Angle it slightly to fit the other end into V-channel of profile L03G. L03G L03F IMPORTANT: L05D is shipped with four hex nuts and bolts attached. Loosen hex nuts on each end and slide towards center. Make sure the pins face up on inside of the greenhouse when profile L05D is installed. L05D L03F L05D L05D VIEW FROM INSIDE. 0.B Line up L05D channel with U-shaped cutouts in sides of profiles L03F and L03G. Slide hex nut and bolts into U-shaped notches and tighten securely. L03F L05D L03G L05D L03G L05D L03G VIEWS FROM INSIDE. #L05D 0.5A Stand on a small step ladder inside the greenhouse. Install roof vent by sliding profile LA into profile L08A from the back of the greenhouse towards the front. LA IMPORTANT: The handle of roof vent is on the inside of the greenhouse. L08A LA Y L08A 0.5B Continue to slide vent past the end of profile L08A until the hole in the other end is visible. Screw SA into hole L08A and slide vent back until it rests next to the screw. L08A Y SA L08A SA Screw #SA 3 of 5

46 Install Circular Vent.A Lay out all the parts for circular vent in a staging area. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. Open the box containing the parts for the circular vent. From the outside of the greenhouse, line up vent frame pins with holes in panel Y6, and slide into place. From the inside of the greenhouse, slide circular vent under the cable. Line up pins in vent frame with holes in vent fan and slide into place. IMPORTANT: Circular vent rests under the bracing cable. See step 3.0 for detailed instructions on adjusting the cables. Y6.B From the inside, secure the vent with four plastic nuts. Y6.C Double check that the corners are squared at 90 degrees and adjust if necessary. See step 3.0 for detailed instructions. Y6 NOTE: VIEWS ARE FROM INSIDE. IMPORTANT: Make sure all corners are squared at 90 degrees. Vent Frame Circular Vent Plastic Nuts of 5

47 Install Side and Roof Panels Lay out all side and roof panels in a staging area. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles.. Remove protective plastic from both sides of panels Y9 and Y0. Place side to face toward the sun facing out when installing. Slide panels carefully into V-channels in corner profiles L0A and L0B and side profiles L03A and L03B. As you continue sliding the panels make sure they fit into the V-channels in base profiles L0C. Y0 Y0 Y9 Y9. Remove protective plastic from both sides of panels Y, Y and Y3. Place side to face toward the sun facing out when installing. Slide panels carefully into V-channels in gable profiles L03E, L03F, L03G and L03H and in front and back profiles L0C, L0D, L0E and L0F. As you continue sliding the panels make sure they fit into the V-channels in center roof profiles L0G. Y9 Y0 Y0 Y9 Y Y Y Y Y3 Y Y Y Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING OUT. Panel Panel Panel #Y0 #Y 3 #Y9 #Y #Y3 5 of 5

48 Install Weather Stripping If you have been building your greenhouse in another place than it s final position, we recommend you move the greenhouse before you begin these steps. Have at least one person help you carry it. NOTE: You will find a roll of 63 meters of black rubber weather proof stripping. You will need a pair of scissors for this step. 3 From the outside of the greenhouse, line up the black rubber stripping with the V-channels of all profiles. Cut to length of each profile as you work, pushing the stripping between the panel and the empty space in the V-channel of the profile. IMPORTANT: The black rubber stripping J0is cut to length with scissors. Make sure to insert stripping as shown, securely into the V-channels of all the profiles, cutting each piece to the proper length. This will help protect the inside of your greenhouse from the weather. Rubber Stripping #J0 63M 6 of 5

49 Install Trim Plates Lay out the trim plates in a staging area. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles.. Remove the six hex nuts from the hex bolts attached to each L09A and L09B trim plate BEFORE installing. L09A L09B VIEWS FROM INSIDE..A Place trim plates L09A and L09B onto profiles L07A and L07B on outside of greenhouse. Trim plates fit over edges of side and roof panels and bolts are inserted into holes on profiles L07A and L07B..B NOTE: Trim plates cover edges of black rubber stripping, and roof and side panels. From inside of greenhouse, place hex nuts onto hex bolts in trim plates L09A and L09B and tighten securely. L07B L09B L07A L09A VIEWS FROM INSIDE. IMPORTANT: The holes in profile L07A and L07B and the bolts in trim plates L09A and L09B are in different positions. Fit trim plate L09A into profile L07A. Fit trim plate L09B into profile L07B..3 Repeat Step.A and.b on other side of greenhouse. Note the positions of profiles L07A and L07B are reversed. Make sure to attach trim plate L09A to profile L07A in the front and trim plate L09B to profile L07B in the back. L07B L09B L09A L07A Trim Plate #L09A #L09B 7 of 5

50 .A In the front of the greenhouse, slide plastic trim plates J0L, J0R, and J03 into connectors S09, S0 and S8 until they snap into place. On top of the greenhouse, snap trim plate J0 onto connector S. The trim plates will cover the edges of the black rubber stripping installed in step 3. S J0 S S8 J03 S0 S0 J0L S09 J0R.B In the back of the greenhouse, slide plastic trim plates J0L, J0R, and J03 into connectors S09, S0 and S until they snap into place. S0 S S09 J0L J03 J0R IMPORTANT: The plastic trim plates J0L, J0R, J03 and J0 fit into connectors one way. Make sure the connectors are snapped securely into place as they will protect the connectors from the weather. Trim Plate Trim Plate Trim Plate Trim Plate #J0L #J0R #J03 #J0 8 of 5

51 Weather Strip and Hang Door The door has been assembled in Step. When hung, the bracing bar is on the inside of the greenhouse. We recommend using two people to hang the door. NOTE: You will use the remainder of the roll of 63 meters of black rubber weather stripping. You will need a pair of scissors for this step. 5. Follow instructions for Step 3 to install rubber weather stripping to outside of the door. IMPORTANT: The rubber stripping J0is cut to length with scissors. Make sure to insert stripping as shown, securely into the V-channels of all the profiles, cutting each piece to the proper length. This will help protect the inside of your greenhouse from the weather. Rubber Stripping #J0 63M 5. From the outside of the greenhouse, carefully line up hinges on door into hinges on door frame and lower into place. There is no need to secure it. 9 of 5

52 Secure to Ground IMPORTANT: The greenhouse must be firmly secured to the ground. Make sure the foundation is FLAT and LEVEL. Make sure the greenhouse is square. The two diagonal measurements inside the greenhouse should be identical. 6 From the inside of the greenhouse, insert the S3 anchor clips into channels of side profile L0C at each corner and center of both sides. Place the S35 pegs through the holes and into the ground to establish proper placement. Remove the pegs, dig holes /30cm deep and fill with concrete. When the concrete is partially dry, use a hammer to drive the pegs all the way into the concrete and let dry completely for twenty four hours. NOTE: Insert S3 anchor clips into the channel of side profiles L0C at a slight angle and slide under the lip of the channel. L0C S35 L0C S3 VIEW FROM INSIDE. Anchor Clip Anchor Peg #S3 6 #S of 5

53 Install Trays and Bin Holder Lay out all the parts for the trays and bin holder in a staging area. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. 7. From the inside of the geenhouse, place the trays on the shelves. The trays interlock together and rest on the lip on the sides of the shelve profiles. Ten trays fit on each side of the greenhouse. 7.A Slide long side of connector S37 into each end of profiles L0E, lining up the last hole on the connector with the hole in the channel. Trays 7.B Secure each S37 connector with one S0 screw. #J05 0 S37 S0 IMPORTANT: S36 are self tapping screws used to screw into areas that do not have predrilled holes. When you have decided on the placement of your bin, use these screws to attach the L0E profiles into the shelf profiles. 7.3A Place profiles L0E on shelve profiles. Position to fit your bin. 7.3B Secure each connector with one S36 screw. L0E S36 L0E NOTE: A cordless drill with a phillips head bit is recommended. #L0E #S37 Screw #S0 #S36 5 of 5

54 Systems Trading Corporation 6 x 8 Easy-Grow Greenhouse Assembly Instructions Please keep this manual in a safe place for reference. If you need any help or have missing or damaged parts, please contact us. Systems Trading Corporation 50 7th Avenue Suite 809, New York, NY 03 Customer Service: (877) ext customerservice@stcaustin.com Copyright 008, Systems Trading Company, All rights reserved.