Interior Wall and Floor Applications. / Mechanical Application / Fuga Fitted System. System Components:
|
|
- Preston Black
- 6 years ago
- Views:
Transcription
1 System Components: Kalesinterflex Composite Facade Board Composite Facade Board: Composite facade board (Kalesinterflex Fit) composed with porcelain ceramic front face, 1000 x 3000 x 3 mm in dimensions, with back face laminated with fiber mesh and special epoxy resin. Front Layer Back Layer Adhesive Porcelain board of 1000 x 3000 x 3 mm Kalesinterflex or of smaller size (500 x 1500 mm, 330 x 1500 mm, etc.) Fiber mesh Special epoxy resin Bearing Construction L anchorages, vertical bearer T profiles, horizontal fuga profiles and fittings constitute the sub-construction of the system. L 50 x 70 x 4 mm l = mm alloy raw aluminum anchorage Vertical bearer profile 50 x 70 x 2 mm, 6063 alloy raw aluminum T profile Horizontal fuga profile 21.5 x 62 mm special cross section 6063 anodized aluminum profile Fuga cover profile 13 x 21 mm special cross section 6063 anodized aluminum clips Fittings > Wall - anchorage connection = 10 x 100 dowel + rod of appropriate type > - vertical bearer T profile connection = Bolt, nut, washer > Vertical - horizontal fuga profile connection = 4.8 x 16 mm screw > Horizontal fuga profile - Kalesinterflex connection = Polyurethane adhesive Application > According to survey made at the jobsite, Kalesinterflex panel layout design is drawn based on standard details. > s are fixed on the face according to the design prepared as above. > Vertical bearer aluminum T profiles are fixed on anchorages with bolts and nuts at a distance of approximately 8 to 15 cm to the face plane. > Horizontal bearer fuga profiles are fixed with screws on vertical bearer T profiles at prescribed horizontal axes defined in the design. > Kalesinterflex slabs prepared to size as defined in the design are fixed on horizontal fuga profile with polyurethane based adhesive. (Vertical joints must be 3 to 6 mm.)
2 Surface preparation and Application For construction applications of 50 x 150 cm or less, (single layer fibre enhanced) must be used and for larger dimensions Kalesinterflex Laminex (double layer laminated) must be used. In compliance with the design prepared, the horizontal supporting joint profiles where the dimensioned Kalesinterflex slabs (50 x 150 cm/free- 33 x 150 cm/free dimension ) will be mounted are fixed with YSB crews on the vertical supporting profiles, at the horizontal axis. Kalesinterflex slabs are mounted on the horizontal supporting joint profiles using polyurethane based adhesives. See Detail A. In an alternative practice, Kalesinterflex slabs (100 x 300 cm etc., Kalesinterflex Laminex of larger dimensions) are mounted, without using horizontal profiles, merely by fixing on vertical profiles with polyurethane based adhesives, to render surfaces in compliance with the details. See Detail B. The back surfaces of the dimensions Kalesinterflex slabs must be meshed or the slabs must be used after being laminated in two layers. Kalekim SeraCare is recommended for Kalesinterflex surface protection. It is useful particularly in rendering the cladding materials resistant against dirt and moss, facilitating future cleaning, and increasing resistance against water, thanks to its water repellent characteristics. Dimensions Product Adhesive* 100x300 cm 100x100 cm 50x150 cm 50x100 cm (4 mm) (4 mm) (4 mm) (4 mm) Mechanical System Interior Wall Applications; dimension-adhesive table.
3 Horizontal Fuga Profile Aluminum T Profile Thermal Insulation SECTION PLAN > Scale: 1/10 Adhesive Wall Dowel Horizontal Fuga Profile
4 Detail A > Scale: 1/10 Wall Bearer Profile Horizontal Fuga Profile Detail B > Scale: 1/10 Wall Bearer Profile Horizontal Fuga Profile
5 Fuga Fitted System / System Detail Plaster Wall Aluminum L Profile > Scale: 1/5 Aluminum L Profile Kalesinterflex Laminex Window Board
6 Fuga Fitted System / Internal Corner System Detail > Scale: 1/5 Plaster / External Corner System Detail > Scale: 1/5 Dowel Aluminum Corner Profile
FRP GATES MM08 FRP GATES Rev. 3 COMPOSITE SOLUTION PAGE 1
FRP GATES MM08 08.02.2016 Rev. 3 FRP GATES COMPOSITE SOLUTION PAGE 1 SUMMARY 1. USES AND CHARACTERISTICS... 3 2. EMPLOYMENT FIELDS... 4 3. MATERIALS... 5 3.1 TABLE OF PROFILES AND STRUCTURAL ACCESSORIES...
More informationTECHNICAL DRAWING GUIDE
Budapest University of Technology & Economics (BME) Faculty of Architecture Department of Building Constructions 2017 + TECHNICAL DRAWING GUIDE Edited by Dr Zsuzsanna Fülöp and Aryan Choroomi based on
More information1. Show the following information with additional information necessary to indicate shop compliance with the requirements of this section.
SECTION 12360 LIBRARY SHELVING PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 06100 - Carpentry. 2. 09200 - Metal Studs, Lath, Suspension Ceiling, Plaster and Stucco. 3. 09660 - Resilient Tile Flooring.
More informationbreathing walls Installation instructions
breathing walls Installation instructions Environmentally friendly Content 1 Application possibilities for ventilating facades 5 1.1 Advantages of ventilated facades 5 1.2 Division of 6 2 Types of TEMPSI
More informationButt Two pieces of wood meeting with flat sides adjoining usually at right angles. Some type of connector is needed to prevent movement.
Wood Connections There are basically five different types of connectors: Interlocking (carpentry joints), Dowel, Metal Connectors, Special Formed Connectors and Adhesives. I Interlocking (Carpentry Joints)
More informationCembrit Patina. Cembrit Cover. Cembrit Solid. Cembrit Transparent
Rainscreen Cladding Your choice. In addition to the range of colours and shades, Cembrit cladding boards are available in four compositions, each with distinctive performance and characteristics. Cembrit
More informationFAÇADES 2 - CT Assignment (circa 30 hours)
FAÇADES 2 - CT 4211 Assignment 1 2008 (circa 30 hours) Introduction The pictures and drawings below show a recently finished building for Stichting De Hoop in Dordrecht (Netherlands), in use as an education
More informationRECOMMENED TOOLS FOR MACHINING COUNTERTOPS
Fabrication Manual RECOMMENED TOOLS FOR MACHINING COUNTERTOPS 1. Blades a) Segmented blade for porcelain. 4. Polishing Discs a) Silicon Carbide velcro discs for dry use. Grit 60, 120, 220, 400. 2. Grinding
More informationSLIDING DOOR SYSTEM_ S34 PRODUCT LIST. System description Accessories
SLIDING DOOR SYSTEM_ S34 PRODUCT LIST System description Accessories SLIDING DOOR SYSTEM_ S34 1.0_ System description_ page 03 2.0_ Profiles_ page 04 3.0_ Profile finishes_ page 08 4.0_ Panels_ page 09
More informationSECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationInstallation instructions for co-extruded louver-board profiles
Installation instructions for co-extruded louver-board profiles www.silvadec.com / info@silvadec.com / tel.:+33 (0)2.97.45.09.00 TO BE READ CAREFULLY BEFORE INSTALLATION Before starting installation on
More informationCURTAIN WALL OPTIONS UNITIZED CURTAIN WALL
CURTAIN WALL OPTIONS UNITIZED CURTAIN WALL Is a type of frame-supporting curtain wall consisting of framing components and panel materials. Such framing components and panel materials are assembled into
More informationADGV_001_FASTPOS. Date Jan 2013 Detail. Profile. Fastener Positioning Scale 1:20 Detail No. ADGV_ mm from top edge. 600mm MAX CTRS TIMBER STUDS
ADGV_001_FASTPOS Panel Timber Frame 12mm from top edge 600mm MAX CTRS TIMBER STUDS 200 mm MAX CTRS 50mm from corner Fastener Positioning Scale 1:20 No. ADGV_001 ADGV_003_SHTEDGEPOS Centre line of Timber
More information1. PREPARATION OF THE SUBSTRATE CLIMATIC CONDITIONS MARKING THE POSITION CUTTING GLUING 17 18
INDEX MOUNTING 1. PREPARATION OF THE SUBSTRATE 4 2. CLIMATIC CONDITIONS 4 3. MARKING THE POSITION 4 5 4. CUTTING 6 5. GLUING 6 7 6. TREATMENT OF THE JOINTS 7 7. MECHANICAL FASTENING 8 8. CONTACT SURFACE
More informationjoining materials - wood
UNIT D E S I G N A N D M A N U F A C T U R E : C O U R S E M A T E R I A L Wood joints joining materials - wood The majority of joints used in woodcraft have been designed specifically to attain the maximum
More informationInstallation Instructions
Installation Instructions Roof edge trim profile Series TAG multi-piece aluminium profile Front face height: 250-1050 mm supplied with patented 4F brackets as standard height-adjustable, horizontally moveable,
More informationShaft Wall SYSTEMS 210 INSTALLATION 211. Shaft Wall systems are fire rated non-load bearing walls used for shafts and service ducts.
SYSTEMS 210 INSTALLATION 211 GENERAL REQUIREMENTS 211 FRAMING 212 PLASTERBOARD LAYOUT 213 PLASTERBOARD FIXING 214 CONSTRUCTION DETAILS 217 Shaft Wall Shaft Wall systems are fire rated non-load bearing
More informationJoshua Woodsman
CONSTRUCTION GUIDE of one of our design Please Note This electronic document is protected by the identifier against unauthorized dissemination on the Internet. Before building any structure make sure you
More informationB Connectors. Automation. Structural Framing System Connectors & Fasteners
BContents B Connectors Gussets... 2 End Fasteners... 4 Anchor Fasteners... 5 Angle Brackets... 6 45 Support Brackets... 8 Butt Fasteners... 9 Hinged Support Brackets... 10-13 Joining Plates... 14-18 Nuts
More informationSAMPLE QUESTION PAPER III ENGINEERING GRAPHICS (046) Time Allowed: 3 hours Maximum Marks: 70
SAMPLE QUESTION PAPER III ENGINEERING GRAPHICS (046) Time Allowed: 3 hours Maximum Marks: 70 Note: (i) Attempt all the questions. (ii) Use both sides of the drawing sheet, if necessary. (iii) All dimensions
More informationCETRIS facade systems
CETRIS 8 Application possibilities for vented CETRIS facades Types of CETRIS boards for CETRIS VARIO facade system CETRIS PLANK facade system Machining of CETRIS facade-boards Packaging and storing of
More informationEXPOSED FASTENING SYSTEM WITH SCREWS OR RIVETS
External EXPOSED FASTENING SYSTEM WITH SCREWS OR RIVETS Parklex Facade may be installed using mechanical fasteners, such as screws or rivets. The panels are attached to vertical battens. In the event that
More informationEdgerail Aluminum Bridge Railing System Specification & Installation Instructions
Edgerail System Specification & Installation Instructions Hill & Smith, Inc 1000 Buckeye Park Road Columbus, Ohio 43207 Tel: 614-340-6294 Fax: 614-340-6296 www.hillandsmith.com Section A System Specification
More informationFEET, WHEELS, FLOOR FASTENINGS, SUPPORTS
SYSTEM COMPONENTS FEET, WHEELS, FLOOR FASTENINGS, SUPPORTS s t r oppu S, s gn i n e t s af r oo l F, s l eehw, t e ef FEET, WHEELS, FLOOR FASTENINGS, SUPPORTS 136 MINITEC PROFILE SYSTEM BASE AND TRANSPORT
More informationFS 5800 EXPANSION JOINT EJ FIRE BARRIER* Installation Instructions
Thermal Structures Inc. FS 5800 EXPANSION JOINT EJ FIRE BARRIER* Installation Instructions FLOOR TO FLOOR (F) ROOF TO ROOF (R) FLOOR TO WALL (FW) ROOF TO WALL (RW) WALL TO WALL (W) CORNER WALL (CW) FLOOR
More informationSDC PUBLICATIONS. Schroff Development Corporation
SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com SECTIONING In chapter 3 you will learn how to create various types of sectional views. Sectional views allow you
More informationMN Modelling Objects and Creating Manufacturing Strategy
Abstract This document and the accompanying files describe the process of modelling a bell housing jig using the 3D software Catia V5. The manufacturing process by which the bell housing would be created
More informationA Shell construction
A Shell construction A 4/2012 Content 1 BASE AND WALL ANCHORING 1.1 Base with mortar bed 1.2 Base with sill plate 1.3 Base with raised sill plate 1.4 Concrete base (mortar bed) 1.5 Concrete base (sill
More informationData Sheet 3820 Englisch
Englisch Profile ZF 3820 WDVS Gewebe-Anputzleiste ZF 3820 Decoupling profile with TPE loop, especially for reinforcements in the ETIC system with Reinforcement Plaster ZF-SiL or ZF-R Properties Self-adhesive,
More informationClopay Models 835/837 Sliding Door System Installation Guide
Clopay Models 835/837 Sliding Door System Installation Guide The aim of this instruction is to guide you through the process of construction and fitting of Sliding Doors. Due to the number of sizes available
More informationWPC DECKING TERRACE BOARDS
WPC DECKING TERRACE BOARDS INSTALATION AND MAINTENANCE INSTRUCTIONS MATERIALS SUBSTRATE PREPARATION DEVOREX WPC Decking system is produced from high quality materials containing selected wood flour and
More informationENGINEERING GRAPHICS
ENGINEERING GRAPHICS Course Structure Parts/Units Topics Marks Unit - I Isometric Projection of Solids 25 Machine Drawing 45 Part A. Drawing of Machine Parts Unit - II Part B. Assembly Drawing and Dis-assembly
More informationExperimental Evaluation of Metal Composite Multi Bolt Radial Joint on Laminate Level, under uni Axial Tensile Loading
RESEARCH ARTICLE OPEN ACCESS Experimental Evaluation of Metal Composite Multi Bolt Radial Joint on Laminate Level, under uni Axial Tensile Loading C Sharada Prabhakar *, P Rameshbabu** *Scientist, Advanced
More informationMoment Resisting Connections for Load Bearing Walls
PRECAST: MOMENT RESISTING CONNECTIONS Moment Resisting Connections for Load Bearing Walls Manish Khandelwal Sr. Structural Engineer, Building Structures, Sweco India Private Limited Design philosophy for
More informationSLIDING DOOR SYSTEM_ S42 PRODUCT LIST. System description Accessories
SLIDING DOOR SYSTEM_ S42 PRODUCT LIST System description Accessories 1 SLIDING DOOR SYSTEM_ S42 1.0_ System description_ page 03 2.0_ Profiles_ page 04 3.0_ System description S1600 fixed panels_ page
More informationIndependent Containment System (ICS)
Installing the Independent Containment System (ICS) Complete these instructions to install the Independent Containment System (ICS). Prerequisites This installation requires a team of at least two people.
More informationPanels, Panel Mounting & Other Accessories
Panels, Panel Mounting & Other Accessories Wire mesh guarding on assembly conveyor line Machine safety enclosure using Lexan panels 108 Multiblock Al 1-105 1-3 Various fastening options for panels on Multiblock
More informationLaminate goes Wall. Installation documentation for wall panelling with gekko-system and Extravagant from CLASSEN.
Laminate goes Wall The new panelling system for walls and ceilings from CLASSEN. Installation documentation for wall panelling with gekko-system and Extravagant from CLASSEN. Important information: Installing
More informationHV Support System. The HV Support System is compatable with all CSS Support Systems:
HV Support System HV Support System The HV Support System is compatable with all CSS Support Systems: Aluminum 225 Stringer Beam Twin Beam Support System Drop Deck Support Systems Deck Panel Support System
More informationROOF CURB INSTALLATION INSTRUCTIONS: VERTICAL STANDING SEAM PANEL
: p: (800) 284-1412 f: (903) 759-3598 www.lmcurbs.com 827 fisher rd longview, tx 75604 Installation Check List: Attach Sub-Frames Layout Curb on Back-up Channels Apply Sealants & Set Curb in Place Fasten
More informationDrawing Types & Construction Drawings
Drawing Types & Construction Drawings Building projects require several types of specialised drawings. This collection of drawings, known as a project set, includes: Location Plan Site Plan Floor Plan
More informationKS SERIES - VERTICAL INSTALLATION
CS-DS-01-KSV CS DISCLAIMER CS-PJ-01-KSV KS42SL EXPANDED PANEL JOINT CS-PJ-02-KSV KS42SL ENGAGED PANEL JOINT CS-PJ-03-KSV KS45SL EXPANDED PANEL JOINT CS-PJ-04-KSV KS45 FLAT ENGAGED PANEL JOINT CS-PJ-05-KSV
More informationMANUFACTURING, INTRODUCTION (620)
DESCRIPTION Manufacturing Technology introduces students to the manufacturing industry. Students must demonstrate knowledge and skill about how manufactures use technology to change raw materials into
More informationTUTORIAL 4: Combined Axial and Bending Problem Sketch Path Sweep Initial Project Space Setup Static Structural ANSYS
TUTORIAL 4: Combined Axial and Bending Problem In this tutorial you will learn how to draw a bar that has bends along its length and therefore will have both axial and bending stresses acting on cross-sections
More informationAMENDMENTS Manual of STANDARD SPECIFICATIONS. Adopted by Standard Specifications Committee. Amendment. No. 6. Published by
AMENDMENTS to 2012 Manual of STANDARD SPECIFICATIONS Adopted by Standard Specifications Committee Amendment No. 6 Published by Utah LTAP Center Utah State University 8305 Old Main Hill Logan UT 84322-8205
More informationConnections in CLT Assemblies
Creating forest sector solutions www.fpinnovations.ca Connections in CLT Assemblies Cross Laminated Timber Symposium Vancouver, BC February 8-9, 2011 M. Mohammad Building Systems Wood Products Division
More informationEasy Step by Step Manual
Easy Step by Step Manual Teletower Mini XL Wall-Floor installation The tower packages #1-#2-#3 Open Base Package #1 for the main tower parts. Here you see the three tower tubes (H-Head, M-Middle, F-Feed)
More informationTYPICAL STANDOFF GLASS RAIL ELEVATION TYPICAL SECTION RS0B20 WITH RECTANGULAR BACK PLATE TYPICAL STAIRS
Revisions By: CRL SRS STANDOFF RAILING SYSTEM CRL GLASS RAIL S RS0B20 w/ RECTANGULAR BACK PLATE CRL'S GLASS RAIL S CAN BE USED FOR MOUNTING GLASS PANELS UP TO 3/4" (19 MM) IN THICKNESS. THE 4" X 8" (102
More informationWalls Fact Sheets. Partition Walls and Walls Cladding. Perforated Board. Sandwich Board
s Partition and Perforated Board Sandwich Board Please consult Viroc Technical File available at www.viroc.pt, on EN language, on Downloads page. Other Viroc Recommended Solutions files, organized by type
More informationDECORATIVE BALUSTRADE
interior and facade mouldings DECORATIVE BALUSTRADE Installation manual for foam polyurethane decorative elements F o r Decorat i n g Walls And Ceilings Tools and materials 4 1 2 11 6 20 10 21 5 3 8 19
More informationHSD-LD-US 06/13 Page 1/5. Components
Page 1/5 Components HSD-LD-Set: HSD-LD-S The HSD-LD-Set consists of HSD-LD-D Dowel Component, the HSD-LD-S Sleeve Component, the Locking Plate and the HSD-LD Epoxy Resin. HSD-LD-D Dowel Component HSD-LD-ULTRA-Set:
More informationHex Bolts & Hex Screws DIN 931/ISO4014 & DIN 933/ISO4017
Hex Bolts & Hex Screws DIN 931/ISO4014 & DIN 933/ISO4017 Diameter: M27 to M52 up to 500 MM in Length Diameter: M16 to M42 up to 300 MM in Length up to 300 MM in Length up to 300 MM in Length up to 300
More informationArchitectural Interior Wall Paneling
Architectural Interior Wall Paneling Compact Laminate Arpa Compact Laminate is comprised of reinforced wood fibres and thermosetting resins which when manufactured under very high pressure and heat produce
More informationSECTION B INDEX STOREFRONT FRAMING SYSTEMS
SECTION B INDEX STOREFRONT FRAMING SYSTEMS B PAGE DESCRIPTION 01 STOREFRONT FRAMING SPECIFICATIONS 02 175 SERIES 1 3/4" (44.5) X 4 1/2" (114.3) FLUSH GLAZE FRAMING FOR SINGLE GLAZING. 06 200 SERIES 2"
More informationOpen Source Foam Cutter
Open Source oam utter 4 axis, cheap, modular N hot wire foam cutter Ver. esc. y ate 0.2 OpenS version R. Lodde 22-10-15 Specifications This machine cuts foam (PS, PP, etc.) by moving a hot wire. The wire
More informationTHESE DETAILS ARE PROVIDED AS A GUIDELINE FOR PROPER PANEL AND ASSOCIATED COMPONENT INSTALLATION, AND ARE BASED ON INDUSTRY ACCEPTED PRACTICES.
FRKPV-DS-01-MTLH FRKPV-PJ-01-MTLH FRKPV-PJ-02-MTLH FRKPV-PJ-03-MTLH FRKPV-FS-01-MTLH FRKPV-FS-02-MTLH FRKPV-BS-01-MTLH FRKPV-BS-02-MTLH FRKPV-BS-03-MTLH FRKPV-BS-04-MTLH FRKPV-OC-01-MTLH FRKPV-IC-01-MTLH
More informationMarking Scheme Engineering Graphics
Marking Scheme Engineering Graphics All Questions are to be answered correctly and accurately. General Note: (i) (ii) (iii) (iv) (v) Marks are to be awarded in proportion to the work done. Mistakes in
More informationDRAWING INSTRUMENTS AND THEIR USES
Chapter - 1A DRAWING INSTRUMENTS AND THEIR USES Drawing Instruments are used to prepare neat and accurate Drawings. To a greater extent, the accuracy of the Drawings depend on the quality of instruments
More informationBLACK WIDOW COMPOSITE
PAGE-1 UPDATED 3-6-2015 REV.1 BLACK WIDOW COMPOSITE Detailed installation manual PAGE-2 UPDATED 3-6-2015 SpiderRax, Inc. REVISION PAGE Installation Manual For BWC-S, BWC-B,BWC-F DATE PAGES REASON OLD LEVEL
More informationSECTION MANUFACTURED CASEWORK
1 GENERAL 1.1 SECTION INCLUDES SECTION 12300 MANUFACTURED CASEWORK A. Work required to complete the manufactured casework indicated by the Contract Documents, and the items necessary for its proper installation.
More informationPneumatic & Hydraulic
Pneumatic & Hydraulic Drill Features Guide Wheels for fast repositioning for all self-propelled machines Bolt On Guide Wheels allows drilling within 152mm of corner Heavy-Duty Feed Cylinders with oversized
More informationPD 3 Dowel Cradle. Load Transfer System Industrial Slab on Ground
PD 3 Dowel Cradle Industrial Slab on Ground Provides the flattest joints Assists in reducing long term maintenance costs Extends the life-cycle of the floor and the asset Engineered to meet Super Flat
More informationFaçade System Trimoterm FTV INVISIO
Façade System Trimoterm FTV INVISIO Façade System Trimoterm FTV INVISIO - Technical Document EN Version December 0 TABLE OF CONTENTS Technical description of the Facade system with Hidden Fixing FTV INVISIO.
More informationFlanged Dowel Box. Load Transfer System INDUSTRIAL SLAB ON GROUND
Flanged Dowel Box INDUSTRIAL SLAB ON GROUND Designed for construction joints in Post Tension or large shrinkage specifications Large lateral movement and expansion capacity Eliminates the need to drill
More informationINSTRUCTION MANUAL FOR
No. TD05-28-1016 Date Mar.17,2005 INSTRUCTION MANUAL FOR Fiberoptic Rotary Joint Optical Component Engineering Information Systems Group Hitachi Cable, Ltd. 1. General This instruction manual describes
More informationThe available roof cover choices are listed below: Fiberglass, Translucent Panels Steel. Shingles, Asphalt/Fiberglass, Irregular Pattern
Navigation Roof Cover Roof Cover The different choices available for roof materials are listed below. Enter the percentage of each roof material found on the home. NOTE: Typically you would enter a percentage
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationSTOLITE CONSTRUCTION SYSTEM EXT.CORNER - MANUF.STONE/STOLITE
RENDER TIMBER FRAMING WALL UNDERLAY CONTINUOUS AROUND CORNERS, POLYPROPYLENE TAPE APPLIED TO PROTECT WALL UNDERLAY 75mm MIN.WIDE CLIP ON MS SEALANT ON PEF ROD SEALANT TO JUNCTION PROPRIETARY MANUF.STONE
More informationApplication Specification Releasable Poke-in Connector 08JUL 2015 REV:A
Application Specification 114-137055 Releasable Poke-in Connector 08JUL 2015 REV:A 1. INTRODUCTION This specification covers the requirements for application of Releasable Poke-in connector for use on
More informationINSTALLATION INSTRUCTION RRU DOUBLE LIGHT POLE MOUNT
INSTALLATION INSTRUCTION RRU Double Light Pole Mount for installation of two RRU units on mast, towers or other vertical structures. CUE DEE YOUR INNOVATIVE PARTNER 1 CONTENTS 1. PRODUCT COVERED IN THIS
More informationInclined Roof System Trimoterm SNV
Inclined Roof System Trimoterm SNV Inclined Roof System Trimoterm SNV - Technical Document EN Version 6 July 2016 TABLE OF CONTENTS 1 Technical Description of Roof System Trimoterm SNV 1 1.1 General 1
More informationALUMINUM PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy
More informationBRIDGE RAILING, 4 TUBE B-26-F POST DETAILS MICHIGAN DEPARTMENT OF TRANSPORTATION
\ ƒ" x 1 " SLOTTED HOLE IN POST AND \ ƒ"! HOLE IN RAIL \ "! x 6" SLOTTED ROUND HEAD BOLTS, WITH 1 PLATE WASHER, 1 LOCK WASHER AND HEX. NUT \ ƒ" x 1 " SLOTTED HOLE IN POST AND \ ƒ"! HOLE IN RAIL \ "! x
More informationDownloaded from ENGINEERING DRAWING. Time allowed : 3 hours Maximum Marks : 70
ENGINEERING DRAWING Time allowed : 3 hours Maximum Marks : 70 Note : (i) (ii) Attempt all the questions. Use both sides of the drawing sheet, if necessary. (iii) All dimensions are in millimeters. (iv)
More information1.) Type: VL-F Single compartment rectangular smoke extraction ducts and fittings
1.) Type: VL-F Single compartment rectangular smoke extraction ducts and fittings 2.) Manufacturer / Place of manufacture: AEROPRODUKT Zrt., 6640 Csongrád, Szegedi út 1., HUNGARY 3.) Function: The smoke
More informationTypical 250 Series Center Drive Conveyor Configuration...3. Typical 250 Series End Drive Conveyor Configuration...4
Table of Contents Typical 250 Series Center Drive Conveyor Configuration...3 Typical 250 Series End Drive Conveyor Configuration...4 Fixed Side Rails 250-0153-LLL, 250-0170-LLL, 250-0174-LLL, 250-0178-LLL,
More informationFootball Goals 7,32x2,44 m
Football Goals 7,32x2,44 m 120x100 mm Professional aluminum football goals 7,32x2,44 m Made of special oval aluminum profile 120x100 mm with double reinforcing ribs. The main frame of the goal powder coated
More informationDrawing nr. Contents of drawing Date Rev. date
Contents of drawing date SPA30--E-EN Fastening to floor, vertical or horizontal installation 72202 SPA3--E-EN Vertical joint, horizontal installation 72202 605206 SPA3--2E-EN Vertical joint, horizontal
More informationPart 7 Assembling the X axis
Part 7 Assembling the X axis 1 2 The X axis is a key part of the printer, it carries the extruder on a carriage that moves the extruder laterally in the X axis. The x axis itself is moved vertically on
More informationInstructions - Stobel V2
Instructions - Stobel V2 Congratulations on the purchase of your Stobel, a high end DLG-competition model from LE-composites. We hope you will be happy and successful. To ensure the optimum build we ask
More informationFir and pine wood (52 %) Portland cement (38 %) made by firing limestone and clay Water (9 %) Wood mineralisation substances (1 %)
Duripanel Structura Product information sheet 1 1 Product composition Duripanel Structura fibre panels are made from: Fir and pine wood (52 %) Portland cement (38 %) made by firing limestone and clay Water
More informationAspen Art Museum Creating Innovative Wood Structure
Aspen Art Museum Creating Innovative Wood Structure Tallinn Wood Architecture Conference November 25-26, 2015 Aspen Art Museum Wood Space Frame THE PLAYERS OUTLINE THE BUILDING CONCEPT THE ARCHITECT S
More informationPRODUCT DATA CATALOG
PRODUCT DATA CATALOG CONTENTS PAGE STANDARD ELEVATIONS 2 STANDARD ELEVATIONS 3 DOOR SPECIFICATIONS 4 LOUVER SPECIFICATIONS 5 GLAZING SPECIFICATIONS 5 DOOR HANDING CHART 6 CLINE STANDARD HARDWARE LOCATIONS
More informationME1105 Engineering Drawing & Design
City University London Term 1 Assessment 2008/2009 School of Engineering and Mathematical Sciences ME1105 Engineering Drawing & Design Student Name:.., Group: Examination duration: Reading time: This paper
More information09/ /2016 HST-83 mm 135. Documentation set Page state Scale System Profile Page
GEALAN Installation Manual Vertical Sliding Door These instructions shall facilitate the planning and execution of building connections of a vertical sliding door. A) Introduction А1: Execution of building
More informationCROSSBAR RAFTER ISOMETRIC
Super Sky Products' typical glazing system consists of glass panels or "lites" which are attached to the main framing members using extruded aluminum "retainers" or "pressure plates". These retainers are
More informationAPPENDIX FENCE GENERAL NOTES
APPENDIX FENCE GENERAL NOTES 1. Fabric: 9 gage, 2" mesh, knuckle top and bottom, placed on the outside of posts, single fabric width for the entire height. 2. All fencing to be standard galvanized finish.
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationDrywall, Wood and Truss Uplift
Drywall, Wood and Truss Uplift Drywall (gypsum board) has to: provide rigidity provide aesthetics provide fire protection not leak air Concerns Wood moves. Drywall does not move. Interesting problem. The
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSHIN KWANG HOT MELT CO., LTD.
ADCOPOLY SHIN KWANG HOT MELT CO., LTD. Hot Melt Adhesive Copolymer Resin and Film Manufacturer Address : CHEOMDAN-RO 285, Danwon-Gu, Ansan City, Kyeonggi Province, South Korea (Seonggok Dong, Sihwa Industrial
More informationSG-30 A P P L I C A T I O N I N S T R U C T I O N S. Directions For Application
1 2 3 General Instructions NOTICE: THESE SHINGLES MUST BE APPLIED TO CONFORM WITH ALL APPLICABLE BUILDING CODES. THESE DIRECTIONS REPRESENT COMMON AND ACCEPTED ROOFING PRACTICES. DEVIATIONS FROM THESE
More informationInstallation Instructions for Solar Snow Pad (SSP-T-3)
Installation Instructions for Solar Snow Pad (SSP-T-3) Warning- Do not use this product on solar arrays where the calculated array snow loads exceed 50 pounds per square foot (psf). Most solar panels are
More information40mm Thermoclick. Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial)
http://www.sundancesupply.com 40mm Thermoclick Type II Class 1 Clear Satin Anodize - 201R1 (Mid Grade Commercial) U-Profile 12' Lengths $39 Out System offers a complete set of extrusions and accessories
More informationInstallation Instructions - Model V4JSD 1
Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)
More informationAMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS A. Drawings and General Provisions of Contract, including General and Supplementary Conditions and
More informationGLOSSARY OF TERMS SECTION 8
GLOSSARY OF TERMS SECTION 8 Anchor Bolt Angle Base Plate Bay Blocking CCB Centerline Chord Cladding Clip Closure Strip An A-307 steel bolt embedded in the concrete footing to anchor the base plate of the
More informationOpen Up Your View With CABLE SYSTEMS
Open Up Your View With CABLE SYSTEMS PRESENTED BY CROWN HERITAGE Our Cable Multiple options to accomodate any deck or stair design Marine Grade 316 stainless steel Swaging is the term used for attaching
More informationScaffolding ACCESSORIES
Scaffolding ACCESSORIES INITIA COMPONENTS FIXED BASE For flat surfaces. With holes in the spigot for attaching the cradle head. The reinforced base plate has a thickness of 5 mm and a surface area of 120
More informationLABORATORY MANUAL COMPUTER AIDED DESIGN LAB
LABORATORY MANUAL COMPUTER AIDED DESIGN LAB Sr. No 1 2 3 Experiment Title Setting up of drawing environment by setting drawing limits, drawing units, naming the drawing, naming layers, setting line types
More information