MK-7 Maintenance Manual Revision3 (Ver R02)

Size: px

Start display at page:

Download "MK-7 Maintenance Manual Revision3 (Ver R02)"

Alexandrina Russell
6 years ago
Views:

1 MK-7 Maintenance Manual Revision3 () 1. Features P2 2. Components P2-P3 3. How to replace the fixed knife and drive knife P4-P7 4. How to adjust the pressure of the knives P8-P9 5. How to adjust the thread dividing hook P10-P12 6. How to adjust the positioning finger P12 7. Trimmer troubleshooting and adjustments P13-P15 8. Parameter List P16-P17 Page 1

1. Features The drive knife doesn t extend out from the front edge of the needle plate. Therefore caps and other garments are not damaged by the protruding knives.

The MK-7 trimmer is faster than the MK-5 due to the MK-5 having to make an intermediate stop before a trim is completed. The MK-7 fixed knife and the drive knife are mounted separately.

2 1. Features The drive knife doesn t extend out from the front edge of the needle plate. Therefore caps and other garments are not damaged by the protruding knives. The embroidery field on Caps near the crown of the cap is better, because the MK-7 needle plate is shorter. The MK-5 required a longer needle plate or an added trimmer guard. The MK-7 trimmer is faster than the MK-5 due to the MK-5 having to make an intermediate stop before a trim is completed. The MK-7 fixed knife and the drive knife are mounted separately. So replacing MK-7 knives is easier than the MK-5. The MK-7 knife durability is better than the MK Components Cylinder bed, etc. QJ Needle plate Assy MK7-T QJ Lower thread knife drive rod QJ Cylinder bed cover for MK-7 NB0QJ Cylinder bed cover for MK7-T QJ Needle plate base MK7-T Page 2

Needle plate Assy QJ270001 Needle plate ASSY MK7-T QJ270011 Cylinder needle plate

Drive knife MK7-T QJ270060 Metal washer MK7-T QJ270090 Bobbin thread keep stay ASSY

5 Washer QJ270080 M3x2 Hex socket set screw (Black, w/glue) Needle plate base

SJ210171 Positioning finger for cylinder(ba) KC271001 Upper knife rotating shaft

3 Needle plate Assy QJ Needle plate ASSY MK7-T QJ Cylinder needle plate MK7-T QJ Drive knife rotating shaft MK-T QJ Wave washer MK7-T QJ Drive knife MK7-T QJ Metal washer MK7-T QJ Bobbin thread keep stay ASSY MK7-T KX Fixed knife fixing screw QJ Fixed knife MK7-T QJ x5x0.5 Washer QJ M3x2 Hex socket set screw (Black, w/glue) Needle plate base QJ Needle plate base MK7-T KX Positioning finger screw for cylinder SJ Positioning finger for cylinder(ba) KC Upper knife rotating shaft HS Thread dividing hook (Cylinder MK5) HS Thread dividing hook fixing stay (short type) Page 3

2) Remove the drive knife rotating shaft and drive knife from the needle plate.

4 3. How to replace the fixed knife and the drive knife 1. How to replace the drive knife 1) Loosen the drive knife rotating shaft with a screw driver. 2) Remove the drive knife rotating shaft and drive knife from the needle plate. 3) Re-assemble the parts according to the figure below. Drive knife rotating shaft MK7-T Wave washer MK7-T Drive knife MK7-T Metal washer MK7-T Page 4

4) After assembling the drive knife and related parts, check the setting of the drive knife and fixed knife with the following procedure; (1) Insert a

Please pay attention not to push down on the knife with your fingertip.

If you move the drive knife by pressing downward, the cutting action is not being tested accurately because there is extra pressure being applied to the

5 4) After assembling the drive knife and related parts, check the setting of the drive knife and fixed knife with the following procedure; (1) Insert a piece of thread into the needle hole (2) Hook the thread on the v-notch of the drive knife. (3) Push the drive knife to the cut position. Please pay attention not to push down on the knife with your fingertip. Please move the drive knife sideways by pushing the back edge of the moving knife, parallel with the needle plate. If you move the drive knife by pressing downward, the cutting action is not being tested accurately because there is extra pressure being applied to the drive knife towards the fixed knife, than what s normal. (4) Cut the thread. Don t put tension on the thread. The thread must be loose. Trimming point * If the knives do not cut properly, you ll need to change the fixed knife pressure. Please refer to 4. How to adjust the pressure of the knives. Page 5

6 2. How to replace the fixed knife 1) Loosen the (2) mounting screws for the fixed knife using a screwdriver. 2) Remove the screws and fixed knife from the needle plate. 3) Re-assemble the parts according to the figure below. Counter knife fixing screw Washer 3.2x5x0.5 Lower thread keep stay assy MK7-T Counter knife MK7-T Page 6

Please pay attention to the following points when you install the fixed knife. B 1.

The edge of the fixed knife must be parallel with the edge of the needle plate, as shown. 2 1 A 2.

If OK, tighten screw B for the fixed knife.

Please refer to procedure on Page 5. * If the knives do not cut properly, you ll need to change the knife pressure.

7 Please pay attention to the following points when you install the fixed knife. B 1. Push the fixed knife in direction 1, and lightly in direction 2 and tighten screw A for the fixed knife. The edge of the fixed knife must be parallel with the edge of the needle plate, as shown. 2 1 A 2. Please check that the thread keep stay assembly is not tilted. It should be parallel with the needle plate. If OK, tighten screw B for the fixed knife. After mounting the fixed knife and related parts, cut the thread manually and check how well the knives cut. Please refer to procedure on Page 5. * If the knives do not cut properly, you ll need to change the knife pressure. Please refer to 4. How to adjust the pressure of the knives. 3. Special attention. Mounting the needle plate to the needle plate base. Driving pin The driving pin of the lower thread knife driving rod must be set into the groove of the drive knife properly. If they are not set properly, the drive knife may be damaged. Page 7

8 4. How to adjust the pressure of the knives 1. The following symptoms may be caused by improper pressure of the knives; The thread is not cut. Cut tail end of the thread after trimming is fuzzy (not cut cleanly). Please adjust the pressure of the knives according to the following procedure. 1) Loosen the (2) fixed knife mounting screws with a screwdriver (* A). * A 2) By tightening the M3x2 hex socket set screw, the fixed knife s angle changes and the pressure between the fixed and drive knives increases. 1 Before adjustment After adjustment Page 8

Tightening the hex socket set screw too much causes a gap between the fixed knife and the trimming position of the drive knife. This may cause trimming errors.

9 Tightening the hex socket set screw too much causes a gap between the fixed knife and the trimming position of the drive knife. This may cause trimming errors. When adjusting the pressure of the knives, please tighten the hex socket set screw a few degrees at a time, and test the cutting action. Fixed knife Drive knife Trimming position <Proper adjustment> The Fixed knife and trimming position of the drive knife should be close to parallel with each other and the thread will be cut correctly. Trimming position The tip of the fixed knife bends as the 3x2 hex socket set screw is tightened. <Tightening the set screw too much> The fixed knife bends too much and causes a gap between the trimming position of the moving knife. This can cause trimming errors. 3) After adjustment, tighten the (2) fixed knife mounting screws that were loosened in step 1 (*A) on Page 7. 4) Cut the thread manually to see if it cuts properly or not. If the trimming is not done correctly, please adjust the pressure of the knives again. Page 9

HS210070 Hook driving rod KC271940C Solenoid lever A KN272401 Eccentric stopper assy M3x5 Hex socket bolt BJ210040 Solenoid stay MK7-T 1) Loosen the

10 5. How to adjust the thread dividing hook (trimmer fork) 1. Please adjust the standby position of the thread dividing hook for MK-7 according to the following procedure. HS Hook driving rod KC271940C Solenoid lever A KN Eccentric stopper assy M3x5 Hex socket bolt BJ Solenoid stay MK7-T 1) Loosen the M3x5 hex socket bolt to allow the hook driving rod to move freely. M3x5 Hex socket bolt Solenoid lever in standby position 2) Move the hook driving rod back and forth to allow a gap between the thread dividing hook and the cylinder bed cover to be 0 ~ 0.5 mm. 0~0.5mm Page 10

3) After that, tighten the M3x5 hex socket bolt to lock the hook

Please adjust the engaged position of the thread dividing hook of

1) Loosen the M4x18 hex socket bolt for the eccentric stopper.

11 3) After that, tighten the M3x5 hex socket bolt to lock the hook driving rod in place. M3x5 Hex socket bolt 2. Please adjust the engaged position of the thread dividing hook of MK-7 according to the following procedure. 1) Loosen the M4x18 hex socket bolt for the eccentric stopper. M4x18 Hex socket bolt 2) Turn the eccentric stopper assy to adjust the engaged position. The gap between the bobbin and thread dividing hook should be 0.7mm when the solenoid lever is in the engaged position. 0.7mm Solenoid lever in the engaged position Page 11

3) After the adjustment, tighten the M4x18 hex socket bolt to lock the eccentric stopper in place. M4x18 Hex socket bolt 6. How to adjust the positioning finger 1.

12 3) After the adjustment, tighten the M4x18 hex socket bolt to lock the eccentric stopper in place. M4x18 Hex socket bolt 6. How to adjust the positioning finger 1. When adjusting the positioning finger, set the positioning finger so the right side of the protruding finger is aligned with the center of the needle, as shown below. Needle position Positioning finger (cylinder) The right side of the positioning finger protrusion is aligned with the center of the needle. Page 12

This can be brought on by improper tension balance of the upper and lower threads and/or types of upper thread.

13 7. Trimmer troubleshooting and adjustments <Case 1 > Situation : Upper thread is cut, but the lower thread is not cut. Reason: The drive knife might not be catching the lower thread because the lower thread is loose and out of position when trimming. This can be brought on by improper tension balance of the upper and lower threads and/or types of upper thread. Solution: In this case, check the tension balance of the upper and lower threads and adjust accordingly. If still a problem, change the values of all the following parameters. MSU2: #08 ATC type 2 MSU1: #23 Trim option -151 MC: Trim vector 35 <Case 2 > Situation : Both the upper and lower threads are not cut. Reason 1: The setting of the drive knife and fixed knife may not be adjusted correctly. Solution 1: Please refer to section 4. How to adjust the pressure of the knives on Page 8. Reason 2: The cutting position of the drive knife might not be set properly. Solution 2: Check the cutting position of the driver knife with the following procedure. 1) Turn the machine OFF. 2) Manually rotate the trimmer cam counter-clockwise so the connection rod moves to its furthest travel limit to the right as shown in the following photos. There should also be a White line painted on the trim lever as shown below. The trimmer cam pin should line up with the White line (as shown) when in the proper position. Cam Pin White Line QJ trimmer cam MK7-T Connection rod The figure at the left describes the position of cam when the connection rod moves to its furthest travel limit to the right The side of the drive cam compared to the side of the trimmer motor bracket should be at an angle of 18.9 degrees when in the correct stop position. Page 13

3) Loosen the M4x6 hex socket bolt for the driving lever.

(The driving knife should be pushed against the fixing knife fixing screw.

M4X6 Hex Socket bolt s KX270010 Fixing screw for fixing knife s QJ270020 Driving knife MK7-T Push forward

visible towards the front side of the inspection hole in the needle plate.

14 3) Loosen the M4x6 hex socket bolt for the driving lever. 4) Push the lower thread knife driving lever (upper) forward until it will not move any further. (The driving knife should be pushed against the fixing knife fixing screw.) 5) Tighten the M4x6 hex socket bolt to lock the lever in place. M4X6 Hex Socket bolt s KX Fixing screw for fixing knife s QJ Driving knife MK7-T Push forward Lower thread knife driving lever (upper) Push forward 6) Double check whether or not the driving pin is visible towards the front side of the inspection hole in the needle plate. The photo and figure below show the proper position. Inspection Hole This line indicates the middle of the Driving Pin. The Driving Pin must be close to the front edge of the hole. Driving Pin 7) Execute a manual trim operation to check whether the thread cuts properly. Page 14

15 Reason 3: The adjustment of the knife protection unit may not be set correctly. Solution 3: The compressed length of the cushion spring for the knife protection unit should be 31mm. If it s more than this, it may cause trimming errors. 31mm Page 15

16 8. Parameter list MC Settings No Item Default Setting value 01 Borer Trim jumps 2 03 Lock stitch 1 04 Clamp type 3 05 Slow up count 3st 06 Trim type 1 07 Trim dir 0 08 Trim vector Low speed Jump divide Stitch back 4 12 Overlap 4 13 Auto start 1 14 Swing 0 15 Frame start S. frame 0 17 Needle down 1 18 Applique T. break admit 0 21 Combine data 0 22 Right limit 115mm 23 Left limit 115mm 24 Back limit 110mm 25 Front limit 110mm 26 LCD mode 0 27 LCD bright 2 28 Roll to roll WS system Clamp frame 0 31 V. clamp 0 32 H. clamp 0 33 Frame option Sequin size L Sequin size R Network type Marker type 1 38 Borer Borer Sequin size L Sequin size R Special MC --- Page 16

17 MSU1, MSU2 settings MSU1 setting list Item Default Set value 01 MC Change UTSM 0 03 T. break off Float speed Jump on speed Cap max. speed Slider off time Fork off time Trim motor off ATC option 0 11 Clamp off angle Color motor off 5 13 Vector control 1 14 Light curtain 0 15 Network 0 16 Detect disable 0 17 F. motor option 0 18 B. changer time 0 19 M. up 10/Hz 0ms 20 M. down 10/Hz 0ms 21 Clamp control 0 22 F. move mode 0 23 Trim option 0 MSU2 setting list Item Default Set value 01 MSU2 protect MSU1 password 5 03 Heads Needles 9 05 Max. speed Slow down start Slow down speed ATC type Color motor type Brake type Motor ratio Stop angle P. coder 0 14 F. motor type 2 15 F. move pattern 2 16 V. motor 1 17 H. motor 0 18 V. sensor 1 19 H. sensor 1 20 Origin sensor 1 21 Jump on angle Jump off angle Roll to roll type WS type WS head space LSC type T. break type Sequin device 0 29 Bobbin changer Chenille type Jump on delay 25ms 32 Jump off delay 25ms Page 17

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C) Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the