Официальный представитель: ООО «СпортРус» , Российская Федерация, г.москва, Варшавское шоссе, д.33 Телефон: (495) ,

Transcription

1 Официальный представитель: ООО «СпортРус» , Российская Федерация, г.москва, Варшавское шоссе, д.33 Телефон: (495) , MTH-1100 OWNER'S MANUAL

2 HARDWARE ILLUSTRATION (A1)HEX BOLT 1/2"x1-1/4"L PARTIAL THREAD QTY.2 (A2)HEX BOLT 1/2"x2-1/4"L PARTIAL THREAD QTY.3 (A3)HEX BOLT 3/8"x5"L PARTIAL THREAD QTY.2 (A4)ROUND ALLEN HEAD 5/16""x1-1/4"L PARTIAL THREAD QTY.4 (A5)HEX BOLT 5/16"x2-3/4"L PARTIAL THREAD QTY.2 (A6)HEX BOLT 5/16"x3"L PARTIAL THREAD QTY.2 (A13)HEX BOLT M8X30L PARTIAL THREAD( ) QTY.2 mm inch 0 1" 2" 3" 4" 5" 6" MTH Page 1.1

3 FRAME HARDWARE ILLUSTRATION (A7)HEX BOLT 1/2"x2-3/4"L PARTIAL THREAD QTY.3 (A8)ROUND ALLEN HEAD 3/8"x2"L PARTIAL THREAD QTY.1 (A9)ROUND ALLEN HEAD M10X40L PARTIAL THREAD QTY.1 (A10)ROUND ALLEN HEAD M6X16L PARTIAL THREAD QTY.16 mm inch 0 1" 2" 3" 4" 5" 6" MTH Page 1.2

4 FRAME HARDWARE ILLUSTRATION FOR MDAA (A11)ELASTIC BELT (F920003) QTY.1 (A12)10LB PIN ( ) QTY.1 mm inch 0 1" 2" 3" 4" 5" 6" MTH Page 1.3

5 HARDWARE ILLUSTRATION (B1)NYLON LOCK NUT 1/2"X8H QTY.2 (C2)1/2"(I.D.)FLAT WASHER Ø34 QTY.3 (B2)NYLON LOCK NUT 1/2" QTY.2 (C3)3/8"(I.D.)ARC WASHER R30 QTY.4 (B3)NYLON LOCK NUT 3/8" QTY.2 (C4)5/16" SPRING WASHER QTY.4 (B4)NYLON LOCK NUT M8 QTY.2 (C5)5/16"(I.D.)FLAT WASHER Ø24 QTY.4 (C1)1/2"(I.D.)FLAT WASHER Ø25 QTY.6 mm inch 0 1" 2" 3" 4" 5" 6" MTH Page 1.4

6 FRAME HARDWARE ILLUSTRATION (B5)NYLON LOCK NUT 1/2" QTY.3 (C10)M6 (I.D.)FLAT WASHER Ø19 QTY.16 (B6)NYLON LOCK NUT M10 QTY.1 (C6)1/2"(I.D.)FLAT WASHER Ø25 QTY.2 (C7)1/2"(I.D.)FLAT WASHER Ø34 QTY.4 (C8)3/8" SPRING WASHER QTY.1 (C9)M10(I.D.)FLAT WASHER Ø19 QTY.2 mm inch 0 1" 2" 3" 4" 5" 6" MTH Page 1.5

7 HARDWARE ILLUSTRATION D1.Ø60 CAP COVER( ) [2PCS] D2.Ø10X60L SHAFT ( ) [1PCS] D3.ROLLER THRUST BEARING( ) [2PCS] D4.Ø1" CU WASHER( ) [6PCS] D5.Ø50 END CAP( ) [6PCS] D6. o50x50x1.8t End Cap ( ) [3PCS] D7.Ø28 PLUG( ) [4PCS] D8.58X116 END CAP( ) [1PCS] D9. Ø27.5X12.5L Rubber Pad( ) [4PCS] D10.95X140 RUBBER PAD( ) [4PCS] D11.108X263 RUBBER PAD( ) [1PCS] D12. 44X54TX99 RUBBER LUMP( ) [1PCS] D13.n115 PULLEY( B) [3PCS] D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 no magnet MTH Page 2

8 HARDWARE ILLUSTRATION D mm BELT(FMTH1100) [1PCS] D15.EXERCISE CHART ( ) [1PCS] D16.EXERCISE CHART ( ) [1PCS] D14 D15 D16 MTH Page 2.1

9 FRAME HARDWARE ILLUSTRATION D17.3/4" SHAFT COLLAR( ) [2PCS] D18.Ø4" RUBBER PAD( ) [2PCS] D19.108X263 RUBBER PAD( ) [2PCS] D20.n115 PULLEY( A) [1PCS] D21.n115 PULLEY( B) [2PCS] D22.BOTTLE BRACKET( ) [1PCS] D23.BOTTLE RACK( ) [1PCS] D24.BOTTLE( ) [1PCS] D17 D18 D19 D20 D21 D22 magnet no magnet D23 D24 MTH Page 3

10 FRAME HARDWARE ILLUSTRATION D25.TOP PLATE( ) [1PCS] D26.Selector Rod( C) [1PCS] D25 D26 MTH Page 3.1

11 159 MTH-1100 ASSEMBLY INSTRUCTIONS PARTS ILLUSTRATION SHEET A[1PCS] B[1PCS] C[1PCS] D[1PCS] E[1PCS] F[1PCS] G[1PCS] H[1PCS] Direction Direction I[1PCS] K[1PCS] L[1PCS] MTH Page 4

12 25 MTH-1100 ASSEMBLY INSTRUCTIONS PARTS ILLUSTRATION SHEET M[2PCS] N[1PCS] O[2PCS] Ø25X356L P[1PCS] X25X6T Q[1PCS] X6TX250L 60 R[1PCS] S[1PCS] T[2PCS] U[2PCS] Ø35xØ25.2x133L 133 MTH Page 5

13 FRAME PARTS ILLUSTRATION SHEET J[1PCS] AA[1PCS] AB[1PCS] AC[1PCS] AD[1PCS] AE[1PCS] MTH Page 6

14 FRAME PARTS ILLUSTRATION SHEET AF[4PCS] AG[1PCS] AH[1PCS] AI[3PCS] AK[1PCS] AM[1PCS] AN[2PCS] AJ[2PCS] AL[2PCS] 5313-R001 Ø3/4"X1243L AO[1PCS] MTH Page 7

15 Above shows STEP 1 assembled and completed C10x2 A10x2 A10x2 AI C10x2 AF A10x2 C10x2 AI AI J AF M10X25L CONE SCREW AF AF A10 x4 C10 x4 AM C10x6 A10x CU WASHER( ) CU WASHER( ) Ø60 CAP COVER( ) D22 AJ M10X25L CONE SCREW X4 MTH Page 8

16 Above shows STEP 2 assembled and completed 1/2"X1-1/4" HEX BOLT X2 1/2" WASHER Ø25 X2 I 1/2"X1-1/4"L HEX BOLT X2 1/2" WASHER Ø34 X2 D8 A 1/2" WASHER Ø25 X2 1/2"X1"L HEX BOLT X2 1/2"X1-1/4"L HEX BOLT X2 1/2" WASHER Ø34 X2 Q M10X25L CONE SCREW X4 3/8"X2"L ROUND ALLEN HEAD BOLT X2 D12 D11 MTH Page 9

17 Above shows STEP 3 assembled and completed O.Ø25X356L shaft( ) short long O long edge D4 D D4 D4 C O long edge D4 B D3 E U D3 MTH Page 10

18 The terminal surface needs to be parallel Above shows STEP 4 assembled and completed Attention *:NEED TO LOOSEH BOTH ALLEN HEAD BOLT IN ORDER TO REMOVE PART#(L) C1 A1 N A13 B4 A13 D6 * A1 C1 L B2 C1 B2 C1 D10x2 D10x2 B4 * D6 * * B1 C1 B1 * * D6 C1 D5x2 D5x2 D5x2 K MTH Page 11

19 Above shows STEP 5 assembled and completed B3x2 C3x2 Mx2 G D4x2 F D1x2 C3 A3 C3 A3 M10X25L CONE SCREW X2 MTH Page 12

20 The belt should reserve 40mm extra length 40 M10X25L RIOUND BOLT X2 M10 SPRING WASHER X2 D14 D17 D17 A9 C9 AG AH Above shows STEP 6 assembled and completed AL AL C8 A8 C9 B6 The tread side should be outward D25 A11 A12 Figure 1 AK D18 D18 M10X25L CONE SCREW Ø60 CAP COVER( ) *ATTENTION* Do not touch the sensor bracket (AK) during weight stack installation CU WASHER( ) CU WASHER( ) line link AL MTH Push guide rods (AL) to tilt one side and then install weight stacks. Once finishing the weight stack installation, pull guide rods (AL) back and continue setup D25 D17 Page 13

21 10 MTH-1100 ASSEMBLY INSTRUCTIONS Above shows STEP 7 assembled and completed NOTE: 1. THE BELT SMOOTH SIDE SHOULD ATTACH ON PULLEY SURFACE, AND THE BELT SMOOTH SIDE WRAP AROUND THE BELT RETAINER SHAFT (AH) 2. PLEASE BE SURE THE PRESSURE BETWEEN THE BELT CLAMPS (AG) DO NOT EXCEED 70 PSI Assemble Direction A7 C6 D20 D21 C6 B5 C7 B5 A7 C7 D21 B5 C7 Detect the distance 5 C7 A7 Adjust Belt Procedure: 1. Lift the selector rod a little and then insert the pin between first weight stack and top plate (Do not insert though the first hole of the rod), and there are 10 mm gap between top plate and first weight stack. 2. Adjust the belt to have proper tension and then tighten the belt clamps 3. Remove the pin and let the top plate fall on the first weight plate. MTH Page 14

22 Above shows STEP 8 assembled and completed NOTE: 1. THE BELT SMOOTH SIDE SHOULD ATTACH ON PULLEY SURFACE, AND THE BELT SMOOTH SIDE WRAP AROUND THE BELT RETAINER SHAFT (AH) 2. PLEASE BE SURE THE PRESSURE BETWEEN THE BELT CLAMPS (AG) DO NOT EXCEED 70 PSI The tread side should be outward D14 A1 D13 C2 H Figure 3 Turn 90 Degrees C D13 C2 A1 The tread side should be outward D13 Figure 2 C2 A1 MTH Page 15

23 LINE A Material detail drawing of line B JST-XHP JST-XHP-9 A B 1 1 BLACK BLACK 2 PLAM 2 PLAM 3 RED 3 RED 4 ORANGE 4 ORANGE 5 5 YELLOW YELLOW 6 GREEN GREEN 6 7 BLUE BLUE 7 8 PURPLE PURPLE 8 9 GREY GREY LINE 1 3 JST-XHP JST-SMP-03V-BC 400 A:HOLE COLOR B:HOLE COLOR 1 BLACK 1 BLACK 2 PALM 2 PLAM 3 RED 3 RED MTH Page 16.1

24 LINE Material detail drawing of line JST-SMR-03V-B 1 3 MTH Page 16.2

25 line link AK line link Above shows STEP 9 assembled and completed Figure Line Line M4X12L ROUND ALLEN CROSS BOLT X2 D24 AB AO LINK D22 AN LINK AA D23 AN LINK AA D22 AA D15 D16 M4X12L ROUND ALLEN CROSS BOLT X4 AC M6X12L ROUND BOLT X5 M6 WASHER Ø14X5 M6 WASHER Ø14X4 M6X12L ROUND BOLT X4 MTH Page 17

26 M10X12L ROUND BOLT X4 AE Above shows STEP 10 assembled and completed AD EXTRUDING EXTRUDING Figure 5 Note: When installing the shroud (AD), push both sides of the shroud toward center in order to bend it a little. After insert it to the door frame and then releasing it. The shroud will be locked on the door frame. MTH Page 18