Fasteners & Accessories For Commercial Construction

Transcription

1 Fasteners & Accessories For Commercial Construction

2 Table of Contents Page Structural Performance Fastener Strength and Pullout Values... 2 Carbon Steel Self-Drill Fasteners, No Washer... 3 Structural Steel Self-Drill Fasteners... 4 Carbon Steel Self-Drill Fasteners, bondseal Washer... 5 Cupped Sealer Self-Drill Fastners, EPDM Washer Stainless Steel Self-Drill Fasteners... 6 ZAC Zinc Aluminum Capped Self-Drill Fasteners... 7 MAC Stainless Capped Self-Drill Fasteners... 7 Flex5 Grade 5 Performance Fasteners... 8 Wood to Metal Self-Drill Fasteners... 9 woodgrip Fasteners woodgrip HiLo Fasteners #14 Milled Point Wood Screw...11 evergrip Bi-Metal 300 Series Stainless Fasteners...11 woodgrip 300 Series Stainless Aluminum Panel Fasteners...11 woodmac Wood Screw woodzac HiLo Zinc Aluminum Capped Fastener Clip Fasteners Page Carbon Steel Self-Tapping Type A Fasteners Stainless Steel Self-Tapping Type A Fasteners Carbon Steel Self-Tapping Type B Fasteners Stainless Steel Self-Tapping Type B Fasteners SX - HWH 304SS Bi-Metal Self-Drill Fasteners irius SX 304SS Bi-Metal Self-Drill Fasteners SX TORX 304SS Bi-Metal Self-Drill Fasteners Blind Rivets BULB-TITE Rivets Blind Rivet Tools Grommet Fasteners Pipe Flashing Hannoband BG1 Joint Sealant Tape vistacoat Premium System #12 Dekfast Phillips Head (insulation attachment) #14 Dekfast Phillips Head (insulation attachment) Insulation Stress Plates Zinc Nailins Structural Performance Fastener Sizes Fastener Size #8 #9 #10 #12 1/4 #14 #17 Thread Diameter Decimal Equivalent Steel Gauge Sizes* Gauge /8 10 3/16 1/4 1/2 Decimal Equivalent (in.) Decimal Equivalent (mm) *Standard steel thickness used for panels, purlins and girts. Fasteners are designed to withstand a varied range of types of loading. Each panel or structural system has its own specifi c fastener loading requirements. Care must be taken to ensure that the appropriate loading requirements for each application are considered. Utlimate Shear Strength The point at which a fastener fails under a load exerted in offset opposing directions, usually upon the shank of the fastener. Typical structural performance criteria that infl uence fastener design include: Ultimate Tension Strength The point at which a fastener fails under a load exerted in two direct opposite direction Ultimate Pull-out Performance The ability of a fastener s threaded connection to remain intact and resist tensile loads. Ultimate Torsion Strength The point at which a fastener fails under a twisting load exerted on the head during installation in a torsional direction. Self-tapping fasteners require that a pilot hole be drilled prior to installation. The pull-out resistance will be directly related to the pilot hole diameter. Self-drilling fasteners have been developed, and are available, for most steel contruction applications, to a metal thickness of 1/2. This type of fastener is manufactured with its own integral drill point, which is engineered to drill the optimum hole size to facilitate effi cient thread forming in the metal structure, resulting in optimized pullout values. 1

3 Structural Performance, continued Ultimate Pull-over performance The ability of a fastener to resist the pulling of the fastened sheet material over the head of the fastener due to gravity, wind, or other load. SFS intec is proud to be a member of these industry trade associations: The resistance to pull-over failure is related to the strength and diameter of the fastener washer and the strength and thickness of the metal panel. Fastener Strength & Pullout Values Strength Values Diameter and TPI Tensile lbs. Min. Shear Avg. lbs. Ultimate Torque Min. in-lbs / / Pullout Values (Average lbs. ultimate) Diameter and TPI Point Size Gauge /8 3/16 1/ * / / / *Denotes tensile failure Disclosure Statement Fastener data shown herein is subject to change or correction for typographical error without notice. All test data and ultimate values shown in the catalog are the result of laboratory testing. Specifi c job conditions should be considered and appropriate safety factors applied when specifying fasteners. In actual applications, proper installation techniques must be used to assure adequate performance of the fastener. Final selection of fasteners or accessories for use is ultimately the decision of the purchaser. While SFS intec, Inc. may assist by providing data and information for comparison, SFS intec makes no suggestions or warranties pertaining to the suitability of its products for any particular application. TORX is a registered trademark of Textron Inc. Hannoband is a registered trademark of Hanno Werk GmbH & Co. KG. 1 Buy American Act - Construction Materials Under Trade Agreements 2

4 Carbon Steel Self-Drill Fasteners Metal to metal applications Buy American Act SD SD3 1/4-14 SD3 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 1/4 AF, No Washer x 1/2 SD x 5/8 SD x 3/4 SD Impax HWH 5/16 AF, No Washer x 5/8 SD x 3/4 w/serration SD x 3/4 SD x 3/4 SD * x 1 SD x 1-1/4 SD x 1-1/2 SD Impax HWH 5/16 AF, No Washer x 3/4 SD x 1 SD x 1-1/4 SD x 1-1/2 SD x 2 SD x 2-1/2 SD x 3 SD x 4 SD /4-14 x 7/8 (lap) SD Impax HWH 3/8 AF, No Washer /4-14 x 3/4 SD /4-14 x 1 SD /4-14 x 1-1/4 SD /4-14 x 1-1/2 SD /4-14 x 2 SD /4-14 x 2-1/2 SD /4-14 x 3 SD /4-14 x 4 SD Indicates domestic Indicates E-Zinc plating 1 Buy American Act - Construction Materials Under Trade Agreements 3

5 Structural Steel Self-Drill Fasteners Metal to metal applications Buy American Act 1 Painted SD5 1/4-20 SD5 Silver Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 5/16 AF, No Washer x 7/8 SD x 1-1/4 SD x 1-1/4 SD x 1-1/2 SD x 2 SD Impax HWH 3/8 AF, No Washer /4-20 x 3 SD * /4-20 x 4 SD * /4-20 x 5 SD * /4-20 x 6 SD * /4-20 x 7 SD * /4-20 x 8 SD * 43.5 Buy American Act SD5 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 5/16 AF, with bondseal Washer x 7/8 SD x 1-1/4 SD x 1-1/4 SD x 1-1/2 SD x 2 SD Impax HWH 3/8 AF, with bondseal Washer /4-20 x 3 SD * /4-20 x 4 SD * /4-20 x 5 SD * /4-20 x 6 SD * /4-20 x 7 SD * /4-20 x 8 SD * Buy American Act - Construction Materials Under Trade Agreements 4

6 Carbon Steel Self-Drill Fasteners with bondseal Washer Metal to metal applications Buy American Act SD SD3 1/4-14 SD3 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax HWH 5/16 AF, with bondseal washer x 5/8 SD x 3/4 SD x 1 SD x 1-1/4 SD * x 1-1/2 SD Impax HWH 5/16 AF, with bondseal Washer x 3/4 SD x 1 SD x 1-1/4 SD x 1-1/2 SD x 2 SD x 2-1/2 SD x 3 SD x 4 SD /4-14 x 7/8 (lap) SD Impax HWH 3/8 AF, with bondseal Washer /4-14 x 3/4 SD /4-14 x 1 SD /4-14 x 1-1/4 SD /4-14 x 1-1/2 SD /4-14 x 2 SD /4-14 x 2-1/2 SD /4-14 x 3 SD /4-14 x 4 SD * Buy American Act - Construction Materials Under Trade Agreements 5

7 Cupped Sealer Self-Drill Fasteners Metal to metal applications Buy American Act SD3 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Impax Cupped HWH 5/16 AF, with EPDM Sealing Washer x 3/4 SD x 1 SD x 1-1/4 SD x 1-1/2 SD /4-14 x 7/8 (lap) SD Stainless Steel Self-Drill Fasteners Metal to metal applications Made in USA Painted SD3 410 SS No Washer SD3 410 SS Aluminum bondseal Washer Silver Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt. 410 Stainless HWH 5/16 AF, No Washer x 3/4 SD x 1 SD x 1-1/4 SD /4-14 x 7/8 (lap) SD Stainless HWH 5/16 AF, with Aluminum bondseal Washer x 3/4 SD * x 1 SD * x 1-1/4 SD x 1-1/2 SD /4-14 x 7/8 (lap) SD Buy American Act - Construction Materials Under Trade Agreements 6

8 ZAC - Zinc Aluminum Capped Self-Drill Fasteners Metal to metal applications Buy American Act SD SD5 E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. ZAC Impax HWH 5/16 AF, with EPDM washer x 1 SD x 1-1/4 SD x 1-1/2 SD x 2 SD /4-14 x 7/8 (lap) SD /4-14 x 1-1/4 SD ZAC Impax HWH 3/8 AF, with EPDM washer x 1-1/4 SD x 1-1/4 SD x 1-1/2 SD MAC - Stainless Capped Self-Drill Fasteners Metal to metal applications Buy American Act SD3 Silver Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. MAC Impax Stainless Capped HWH 5/16 AF, with EPDM Washer x 1 SD x 1-1/4 SD x 1-1/2 SD /4-14 x 7/8 (lap) SD Buy American Act - Construction Materials Under Trade Agreements 7

9 Flex5 Selectively Hardened Fasteners with Grade 5 Performance Made in USA Material No. Description Drill Pt. Drill & Tap Capacity Load Bearing Area Carton Qty. Carton Wt.. Flex Self-Drill; HWH x 3/4 SD * x 7/8 SD * x 1 SD * x 1-1/2 SD * x 2 SD * 16 Flex Self-Drill; PUF (Phillips Undercut Flat) X 1 SD * 36 Flex Self-Drill; HWH x 1-3/4 SD * 36 Flex5 1/4-14 and 1/4-20 Self-Drill; HWH /4-14 x 1 SD * /4-14 x 1-1/2 SD * /4-14 x 2 SD * /4-20 x 1-1/8 SD * /4-20 x 1-1/2 SD * /4-20 x 2 SD * /4-20 x 2-1/2 SD * 19 Flex5 self-drilling fasetners are made from alloy steel and are fi nished with a selective hardness heat treatment process to give the load bearing part of the fastener Grade 5 specifi cations (RC 28-34), with a higher hardness for the drill point and lead-in threads (min. RC 52). Finish: vistacorr TM SD3 Flex5 1/4-14 SD3 Flex5 Flex5 Head Marking Grade 5 head and threads (RC 28-34) Ideal for curtainwall, architectural cladding, rainscreen and dissimilar metal applications when used with aluminum. Higher-hardness lead threads and point (min. RC 52) Technical Data Pullout Test Results - Steel Screw Size Point Type Panel Thickness Drill Cap /8 3/16 1/4 5/ / / Pullout Test Results - Aluminum Screw Size Point Type Panel Thickness Drill Cap. 1/8 1/4 3/ / / Shear Test Results - Steel Screw Size Point Type Panel Thickness Drill Cap /8-3/16 3/16-1/4 1/4-12 ga / / Shear Test Results - Aluminum Panel Thickness Screw Size Point Type Drill Cap. 1/8-1/8 18/ / /

10 Wood to Metal Self-Drilling Fasteners For attaching wood to steel Buy American Act 1 1/4-20 SD4 Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Ply Metal Self-Drill with Wings; Wafer Head, #2 Phillips Drive x 1-7/16 SD /4 Plywood Header Self-Drill with Wings; Flat Head, #3 Phillips Drive x 2 SD up to x 2-1/2 SD up to 1-1/ Header Self-Drill with Wings; Flat Head, #3 Phillips Drive /4-20 x 2-3/4 SD Steel up to 1-3/4 Wood Brown Vista coating for corrosion resistance Suitable for pressure treated wood Exceeds 1,000 hours salt spray testing Wings designed to ream a hole to prevent "wood jacking" Excellent for wood or header attachments to steel Meets ASTM C1513 for cold-formed steel frame connections 1 Buy American Act - Construction Materials Under Trade Agreements 9

11 woodgrip TM Fasteners Metal to wood applications 9-15 woodgrip Silver Color Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodgrip HWH 1/4 AF, with controlseal washer x 1 Sharp Pt. 24 ga (.024) x 1-1/2 Sharp Pt. 24 ga (.024) x 2 Sharp Pt. 24 ga (.024) x 2-1/2 Sharp Pt. 24 ga (.024) x 3 Sharp Pt. 24 ga (.024) x 3/4 (lap) Sharp Pt. 2 x 24 ga Silver Color woodgrip TM HiLo Wood Screw Metal to wood applications woodgrip HiLo Silver Color Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodgrip HiLo, HWH 1/4 AF, with bondseal Washer x 1 Type 17 Pt. 24 ga (.024) x 1-1/2 Type 17 Pt. 24 ga (.024) x 2 Type 17 Pt. 24 ga (.024) x 2-1/2 Type 17 Pt. 24 ga (.024) x 3 Type 17 Pt. 24 ga (.024) x 3/4 (lap) Sharp Pt. 2 x 24 ga

12 #14 Milled Point Wood Screw Metal to wood applications #14 Type 17-A MP Silver Color Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. #14 Wood Fastener, HWH 5/16 AF. Type 17-A Milled, with bondseal Washer x 1 Type 17-A MP x 1-1/2 Type 17-A MP x 2 Type 17-A MP x 2-1/2 Type 17-A MP x 3 Type 17-A MP evergrip Bi-Metal 300 Series Stainless Fasteners Metal to wood applications 9-15 evergrip Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. evergrip Bi-Metal Stainless HWH 1/4 AF, with Stainless bondseal Washer x 1 Sharp Pt. 24 ga (.024) x 1-1/2 Sharp Pt. 24 ga (.024) x 2 Sharp Pt. 24 ga (.024) x 2-1/2 Sharp Pt. 24 ga (.024) woodgrip 300 Series Stainless Aluminum Panel Fasteners Aluminum panel applications Painted Colors SS woodgrip Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt Series Stainless Aluminimum Panel woodgrip, 1/4 HWH, Aluminum bondseal Washer x 1 Sharp Pt..032 Alum. Max x 1-1/2 Sharp Pt..032 Alum. Max x 2 Sharp Pt..032 Alum. Max x 2-1/2 Sharp Pt..032 Alum. Max x 3 Sharp Pt..032 Alum. Max

13 woodmac TM Wood Screw Metal to wood applications 9-15 woodmac E-Zinc Plating Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodmac 1/4 Stainless Capped HWH with EPDM Washer x 1 Sharp Pt. 24 ga (.024) x 1-1/2 Sharp Pt. 24 ga (.024) x 2 Sharp Pt. 24 ga (.024) x 2-1/2 Sharp Pt. 24 ga (.024) x 3 Sharp Pt. 24 ga (.024) x 3/4 (lap) Sharp Pt. 2 x 24 ga woodzac TM HiLo Zinc Aluminum Capped Fasteners Metal to wood applications woodzac HiLo E-Zinc Plating Painted Colors Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. woodzac HiLo, 5/16 AF Zinc Alloy Capped, with Aluminum bondseal Washer x 1 Type 17 Mill Pt. 24 ga (.024) x 1-1/2 Type 17 Mill Pt. 24 ga (.024) x 2 Type 17 Mill Pt. 24 ga (.024) x 2-1/2 Type 17 Mill Pt. 24 ga (.024) x 3 Type 17 Mill Pt. 24 ga (.024) x 3/4 (lap) Sharp Pt. 2 x 24 ga

14 Clip Fasteners Standing Seam Panel Clip #10 Type A Pancake #12-8 XG Pancake #12-8 XG Low Profi le #12 Type A Pancake #10 SD2 Pancake #12 SD 2 Pancake #12-24 SD5 Pancake E-Zinc Plating Material No. Description Drive Type Drill Pt. Carton Qty. Carton Wt.. Metal to Wood Application x 1 Pancake 2/2 Square Phillips Type A x 1-1/2 Pancake 2/2 Square Phillips Type A x 2 Pancake 2/2 Square Phillips Type A x 1 XG Pancake 2/2 Square Phillips Sharp Pt x 1-1/2 XG Pancake 2/2 Square Phillips Sharp Pt x 2 XG Pancake 2/2 Square Phillips Sharp Pt x 1 XG Low Profi le 2/2 Square Phillips Sharp Pt x 1-1/2 XG Low Profi le 2/2 Square Phillips Sharp Pt x 2 XG Low Profi le 2/2 Square Phillips Sharp Pt x 1 Pancake 2/2 Square Phillips Type A x SS Pancake #2 Phillips Type A x SS Pancake #2 Phillips Type A Metal to Metal Appplication x 1 Pancake 2/2 Square Phillips SD x 1-1/2 Pancake 2/2 Square Phillips SD x 2 Pancake 2/2 Square Phillips SD x 1 Pancake 2/2 Square Phillips SD x 1-1/2 Pancake 2/2 Square Phillips SD

15 Carbon Steel Self-Tapping Type A Fasteners Metal panel applications #14 Type A Metal thickness Drill bit size /8 (.125) /16 (.187) #8 (.199) E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt... Self-Tapping - Type A - Carbon Steel; 3/8 HH with bondseal x 3/4 Type A Pre-drill required.500" x 1 Type A Pre-drill required.750" x 1-1/4 Type A Pre-drill required 1.000" x 1-1/2 Type A Pre-drill required 1.250" x 2 Type A Pre-drill required 1.750" x 2-1/2 Type A Pre-drill required 2.250" x 3 Type A Pre-drill required 2.750" x 3-1/2 Type A Pre-drill required " 1250* x 4 Type A Pre-drill required " 1000* x 5 Type A Pre-drill required " 750* x 6 Type A Pre-drill required " 500* 29.5 Fasteners 3" and longer shall have minimum 3" thread length. Fasteners less than 3" are fully threaded. 304 Stainless Steel Self-Tapping Type A Fasteners Metal panel applications #14 Type A Metal thickness Drill bit size /8 (.125) /16 (.187) #8 (.199) E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt... Self-Tapping - Type A Stainless Steel; 3/8 HH with Stainless bondseal x 3/4 Type A Pre-drill required.500" x 1 Type A Pre-drill required.750" x 1-1/4 Type A Pre-drill required 1.000" x 1-1/2 Type A Pre-drill required 1.250" x 2 Type A Pre-drill required 1.750" x 2-1/2 Type A Pre-drill required 2.250" x 3 Type A Pre-drill required 2.750" x 3-1/2 Type A Pre-drill required " 1250* x 4 Type A Pre-drill required " 1000* x 5 Type A Pre-drill required " 750* x 6 Type A Pre-drill required " 500* 29.5 Fasteners 3" and longer shall have minimum 3" thread length. Fasteners less than 3" are fully threaded. 14

16 Carbon Steel Self-Tapping Type B Fasteners Metal panel applications 1/4-20 Type B Metal thickness Drill bit size #8 (.199) #7 (.201) #1 (.228) #1 or larger (depending on hardness of steel) E-Zinc Plating Material No. Description Drill Type Drill Capacity Carton Qty. Carton Wt. Self-Tapping - Type B - Carbon Steel; 3/8 HH with bondseal /4-14 x 3/4 Type B Pre-drill required.550" 2500* /4-14 x 1 Type B Pre-drill required.800" 2500* /4-14 x 1-1/2 Type B Pre-drill required 1.300" 2000* /4-14 x 2 Type B Pre-drill required 1.800" 2000* /4-14 x 2-1/2 Type B Pre-drill required 2.300" 1500* /4-14 x 3 Type B Pre-drill required 2.800" 1500* /4-14 x 3-1/2 Type B Pre-drill required " 1250* /4-14 x 4 Type B Pre-drill required " 1000* /4-14 x 5 Type B Pre-drill required " 750* /4-14 x 6 Type B Pre-drill required " 500* 33.0 Fasteners 3" and longer shall have minimum 2-7/8" thread length. Fasteners less than 3" are fully threaded. 304 Stainless Steel Self-Tapping Type B Fasteners Metal panel applications 1/4-20 Type B Metal thickness Drill bit size #8 (.199) #7 (.201) #1 (.228) #1 or larger (depending on hardness of steel) E-Zinc Plating Material No. Description Drill Pt. Drill Capacity Carton Qty. Carton Wt.. Self-Tapping - Type B Stainless Steel; 3/8 HH with Stainless bondseal /4-14 x 3/4 Type B Pre-drill required.550" 2500* /4-14 x 1 Type B Pre-drill required.800" 2500* /4-14 x 1-1/2 Type B Pre-drill required 1.300" 2000* /4-14 x 2 Type B Pre-drill required 1.800" 1500* /4-14 x 2-1/2 Type B Pre-drill required 2.300" 1500* /4-14 x 3 Type B Pre-drill required 2.800" 750* /4-14 x 3-1/2 Type B Pre-drill required " 1250* /4-14 x 4 Type B Pre-drill required " 1000* /4-14 x 5 Type B Pre-drill required " 750* /4-14 x 6 Type B Pre-drill required " 500* 33.0 Part number not set up in SAP. Use description to order. Fasteners 3" and longer shall have minimum 2-7/8" thread length. Fasteners less than 3" are fully threaded. 15

17 SX - HWH 304SS Bi-Metal Self-Drill Fasteners Metal to Metal Applications Buy American Act 1 SX3 Stainless bondseal SX5 Stainless bondseal SX14 No Washer Painted Colors Material No. Description Drill Capacity Carton Qty. Carton Wt.. SX3 Self-Drill with Stainless bondseal Washer, 5/16 AF HWH x 1-1/ x 1-1/ x SX3 Self-Drill No Washer, 5/16 AF HWH x 1-1/ x 1-1/ x SX5 Self-Drill with Stainless bondseal Washer, 5/16 AF HWH x 1-1/ x 1-1/ x 1-5/ x 2-1/ x 3-1/ x 3-3/ SX5 Self-Drill No Washer, 5/16 AF HWH x 1-1/ x 1-1/ x 1-5/ x 2-1/ x 3-1/ x 3-3/ SX14 Self-Drill with Stainless bondseal Washer, 5/16 AF HWH x 1-9/ x 1-7/ x 2-1/ x 3-1/ SX14 Self-Drill No Washer, 5/16 AF HWH x 1-9/ x 1-7/ x 2-1/ x 3-1/ SL2 Lap with Stainless bondseal Washer, 5/16 AF HWH x 1 (lap) /4-14 x 1-1/8 (lap) SL2 Lap No Washer x 1 (lap) Buy American Act - Construction Materials Under Trade Agreements 16

18 irius SX 304SS BiMetal Self-Drill Fasteners Metal to Metal Applications Buy American Act 1 irius SX3 No Washer irius SX5 Stainless bondseal Material No. Description Drill Capacity Carton Qty. Carton Wt.. SX3-L12 irius Self-Drill with Stainless bondseal Washer x 1-1/ x 1-1/ SX3-L12 irius Self-Drill No Washer x 1-1/ x 1-1/ x 1-1/ SX5-L12 irius Self-Drill with Stainless bondseal Washer x 1-1/ x 1-1/ x 1-5/ x 2-1/ x 2-7/ SX5-L12 irius Self-Drill No Washer x 1-1/ x 1-1/ x 1-5/ x 2-1/ x 2-7/ SX14-L12 irius Self-Drill with Stainless bondseal Washer x 1-9/ SX14-L12 iirius Self-Drill No Washer x 1-9/ SL2-L12 irius Self-Drill with 14mm SS bondseal Washer /4-14 x 1 (lap) SL2-L12 irius Self-Drill with 16mm SS bondseal Washer /4-14 x 1 (lap) Painted Colors Installation: The E420 irius drive socket (#973316) is required. 1 Buy American Act - Construction Materials Under Trade Agreements 17

19 SX - TORX 304SS BiMetal Self-Drill Fasteners Metal to Metal Applications Rainscreen cladding Facade Panel (HPL, fiber cement) Buy American Act 1 Painted Colors SX5 TORX No Washer SX5 TORX Stainless bondseal Material No. Description Drill Capacity Carton Qty. Carton Wt.. SX3-D10 TORX No Washer (T20W) x SX3-D12 TORX No Washer (T25) x 1-3/ x 2-1/ SX5-D12 TORX with Aluminum bondseal Washer (T25) x 1-1/ SX5-D12 TORX No Washer (T25) x 1-1/ SL2-S-D12 TORX with Aluminum bondseal Washer (T20W) x 1-1/16 (lap) SL2-S-D12 TORX No Washer (T20W) x 1-1/16 (lap) Blind Rivets Blind rivet attach light gauge Made in USA Call customer service for painted color rivet options Material No. Description US Dimens. Grip Range Pre-Drill Hole Size Carton Qty. Carton Wt.. All Aluminum Rivet - Dome Head / Rivet Diameter - 1/ AA42D Rivet #30 ( ) AA43D Rivet #30 ( ) AA44D Rivet #30 ( ) All Stainless Rivet - Dome Head / Rivet Diameter - 1/ STST43D Rivet #30 ( ) STST44D Rivet #30 ( ) STST46D Rivet #30 ( ) Buy American Act - Construction Materials Under Trade Agreements 18

20 BULB-TITE Rivets s for up to grip range Made in USA Material No. Description Rivet Diameter Grip Range Pre-Drill Hole Size Carton Qty. Carton Wt.. Aluminum/Aluminum Dome Head Protruding Crown - With Washer RV W 5/ #20 ( ) 3500* RV W 5/ #20 ( ) 3500* RV W 3/ #4 ( ) 3000* RV W 3/ #4 ( ) 3000* RV W 3/ #4 ( ) 3000* RV W 3/ #4 ( ) 3000* RV W 3/ #4 ( ) 2000* RV W 3/ #4 ( ) 2000* RV W 3/ #4 ( ) 1500* RV W 3/ #4 ( ) 1500* RV W 3/ #4 ( ) 1500* RV W 1/ /4 ( ) 2000* RV W 1/ /4 ( ) 2000* RV W 1/ /4 ( ) 2000* RV W 1/ /4 ( ) 1500* RV W 9/ /16 ( ) 1000* RV W 9/ /16 ( ) 1000* RV W 9/ /16 ( ) 1000* 3.0 Aluminum/Aluminum Dome Head Protruding Crown - No Washer RV / #20 ( ) 3500* RV / #20 ( ) 3500* RV / #4 ( ) 3000* RV / #4 ( ) 3000* RV / #4 ( ) 3000* RV / #4 ( ) 3000* RV / #4 ( ) 2000* RV / #4 ( ) 2000* RV / #4 ( ) 1500* RV / #4 ( ) 1500* RV / #4 ( ) 1500* RV / /4 ( ) 2000* RV / /4 ( ) 2000* RV / /4 ( ) 2000* RV / /4 ( ) 1500* RV / /16 ( ) 1000* RV / /16 ( ) 1000* RV / /16 ( ) 1000*

21 BULB-TITE Rivets, continued s for up to grip range Made in USA Material No. Description Rivet Diameter Grip Range Pre-Drill Hole Size Carton Qty. Carton Wt.. Aluminum/Aluminum Large Flange Protruding Crown - With Washer RV W 9/ /16 ( ) 1000* RV W 9/ /16 ( ) 1000* RV W 9/ /16 ( ) 1000* 7.0 Aluminum/Aluminum Large Flange Protruding Crown - No Washer RV / /16 ( ) 1000* RV / /16 ( ) 1000* RV / /16 ( ) 1000* 7.0 Blind Rivet Tools Installation tools for blind rivets AccuBird 14.4 Volt Cordless Riveting Tool Material Number: Weight: 4.8 lbs Power Pack: 14.4 Volt, rechargeable Li-Ion / 1.3 Ah Battery Charger: 110V/60Hz, 60 minute charge time Buy American Act 1 PowerBird (Recommended for BULB-TITE rivets) 14.4 Volt Cordless Riveting Tool Material Number: Weight: 4.8 lbs Power Pack: 14.4 Volt, rechargeable Li-Ion / 2.6 Ah Battery Charger: 110V/60Hz, 60 minute charge time Note: 9/32 diameter BULB-TITE will require Nose tip and shorter jaws required. Batteries: Volt, 1.3 Ah Li-Ion Battery Volt, 2.6 Ah Li-Ion Battery Grommet Fastener Attach fi berglass panels Made in USA Material No. Description Head Style Washer Carton Qty. Carton Wt.. Stainless Grommet / Stainless bondseal x 7/8 5/16 AF Hex 15 mm O.D. 3500* x 1-1/4 1/4 AF Hex 12 mm O.D. 2500*

22 Pipe Flashing Square and round base pipe roof pipe flashing Material No. Black EPDM Material No. Gray EPDM Material No. Red Silicone Flasher Size Pipe Diameter Carton Qty. Carton Wt.. Square Base Pipe Flashing #1 1/4 to 2-3/ #2 7/8 to #3 1/4 to 5-3/ #4 2-3/4 to #5 4 to 8-1/ #6 4-3/4 to #7 5-1/2 to #8 6-3/4 to 13-1/ #9 9-1/2 to 20-1/ #10 12 to 28-1/ Retrofit Square Base Pipe Flashing #1 1/2 to #2 4 to 9-1/ #3 9-1/4 to 16-1/ Round Base Pipe Flashing #1 1/4 to 2-1/ #2 1-3/4 to #3 1/4 to #4 3 to 6-1/ #5 4-1/2 to 7-3/ #6 5 to #7 6 to #8 7 to #9 9 to Retrofit Round Base Zipper Pipe Flashing #1 3/4 to 2-3/ #2 2 to 7-1/ #3 3-1/4 to Part number not set up in SAP. Use description to order. Made in USA 21

23 Use for sealing joints and seams in metal panels, gaps around door and window frames, and expansion joints in buildings Pre-compressed, self-expanding polyurethane foam Acrylate dispersion impregnation Resistant to rain, wind, sun/uv, sound, draft and dust Pressure sensitive adhesive for fast and easy installation Flame retardant Hannoband BG1 Joint Sealant Tape Material No. Size Thickness x Width Expanded 100% Performance Fully Expanded Uncompressed Thickness Length/Roll Packaging /4 x 1 1/4 1 x ft. 12 rolls/ctn /8 x 1 3/8 1-1/2 x ft. 12 rolls/ctn 8.0 Ctn. Wt. Application vistacoat Premium System High Performance Color Finish SFS intec developed the vistacoat Premium System fi nish for panel attachment fasteners. Utilizing new coating and processing technology, the fi nish has improved appearance, corrosion resistance, durability and installation performance. The fi nish system consists of: pre-treatment seal coat color top coat - contact SFS intec for color matches zinc plating primer coat Silver vistacoat is standard. Performance Corrosion Resistance - on all plain and color product Kesternich per DIN liter - 15 cycles Salt Spray per ASTM B117 1,000 hrs. Consistent Durability Adhesion Impact resistance Appearance gloss and color; application processes ensure consistent results UV Resistance New superior UV-resistant pigmentation Results exceed previous market offerings in gloss retention and color stability 22

24 #12 Dekfast Phillips Head For insulation attachment For attachment to: Steel roof decks Wood roof decks E-Coat Plating Application / Thickness Material No. Description Steel Wood Concrete Carton Qty. Carton Wt.. #12 Dekfast, #3 Phillips drive, 13 tpi, drill point x 1-5/8" Up to 7/8" Up to 5/8" N/A 1000* x 2-1/4" 5/8" to 1-1/2" Up to 1-1/4" N/A 1000* x 2-7/8" 5/8" to 2-1/8" Up to 1-1/8" N/A 1000* x 3-1/4" 1/2" to 2-1/2" 1/2" to 2-1/4" N/A 1000* x 3-3/4" 1" to 3" 1" to 2-3/4" N/A 1000* x 4-1/2" 3/4" to 3-3/4" 3/4" to 3-1/2" N/A 1000* x 5" 1-1/4" to 4-1/2" 1-1/4" to 4" N/A 1000* x 6" 2-1/4" to 5-1/4" 2-1/4" to 5" N/A 1000* x 7" 3-1/4" to 6-1/4" 3-1/4" to 6" N/A 500* x 8" 4-1/4" to 7-1/4" 4-1/4" to 7" N/A 500* 28 Approvals Dekfast fasteners and plates are Factory Mutual approved for attachment of insulation board to roof deck. Refer to FM Approval Guide and Supplements for current FM approved insulation fastening patterns. #12 fasteners meet Factory Mutual corrosion-resistance Standard Installation Tools: rpm screw guns with hardened #3 Phillips bit. The standard carton package includes one #3 Phillips bit. 23

25 #14 Dekfast Phillips Head For insulation and membrane attachment For attachment to: Steel roof decks Wood roof decks Structural concrete roof decks E-Coat Plating Material No. Description Application / Thickness Steel Wood Concrete Carton Qty. Carton Wt.. #14 Dekfast, #3 Phillips drive, 10 tpi, drill point x 1-1/4" Up to 1/2" Up to 1/4" Up to 1/4" 1000* x 2" Up to 1-1/4" Up to 1-1/4" Up to 1" 1000* x 3" Up to 2-1/4" Up to 2" Up to 2" 1000* x 4" 1-1/4" to 3-1/4" 1-1/4" to 3" 2" to 3" 1000* x 5" 1-1/4" to 4-1/4" 1-1/4" to 4" 3" to 4" 1000* x 6" 2-1/4" to 5-1/4" 2-1/4" to 5" 4" to 5" 1000* x 7" 3-1/4" to 6-1/4" 3-1/4" to 6" 5" to 6" 500* x 8" 4-1/4" to 7-1/4" 4-1/4" to 7" 6" to 7" 500* x 9" 5-1/4" to 8-1/4" 5-1/4" to 8" 7" to 8" 500* x 10" 6-1/4" to 9-1/4" 6-1/4" to 9" 8" to 9" 500* x 11" 7-1/4" to 10-1/4" 7-1/4" to 10" 9" to 10" 500* x 12" 8-1/4" to 11-1/4" 8-1/4" to 11" 10" to 11" 500* 45 Approvals Dekfast fasteners and plates are Factory Mutual approved for attachment of insulation board and/or roof cover to roof deck. Refer to FM Approval Guide and Supplements for current FM approved insulation fastening patterns. #14 fasteners meet Factory Mutual corrosionresistance Standard Installation Tools: rpm screw guns with hardened #3 Phillips bit. For structural concrete, 3/16" carbide bit and 1500 rpm max screw guns, or hammerdrills in the hammer mode. Structural concrete to be pre-drilled to minimum 1/2" deeper than fastener penetration. The standard carton package includes one #3 Phillips bit. Insulation Stress Plates For insulation attachment Use with: #12 Dekfast fasteners #14 Dekfast fasteners Made in USA AZ50 Galvalume Material No. Description Outside Diameter Inside Diameter Carton Qty. Carton Wt.. Insulation Stress Plates Galvalume Steel Hex Insulation Plate 2-7/8" Hex.270" 1000* Galvalume Steel 3" Round Insulation Plate 3" Round.260" 1000*

26 Zinc Nailins For fastening termination bar at wall terminations For attachment to: Concrete Block Brick Stone Material No. Diameter & Length Carton Qty. Carton Wt.. Zinc Nailin, Mushroom Head, Zamac 7 Body /16 x 7/8" 500* /4 x 3/4" /4 x 1" 500* /4 x 1-1/4" 500* /4 x 1-1/2" 500* /4 x 2" 500* 16 * inner boxes of 100 pc./box Performance Load Capacities (4000 psi concrete) Diameter 3/16" 1/4" 1/4" 1/4" 1/4" 1/4" Embed. Depth 3/4" 5/8" 7/8" 1-1/8" 1-3/8" 1-7/8" Tension Load (lbs) Shear Load (lbs) Notes: Load capacity is related to embedment depth. Select anchor length to provide needed embedment depth for the installed anchor. The 1-1/4" length is popular for 1/8" composite thickness applications resulting in 1-1/8" embedment. All load values listed are ultimate load capacities and are not allowable load capacities. These loads should be reduced by an appropriate safety factor of at least 4 to determine the allowable load. Installation Tools: Carbide-tipped masonry drill bit sized slightly larger than nominal diameter to allow clearance. A 3/16" nominal masonry drill bit is actually.198"-.206" diameter. A 1/4" nominal size is actually.260"-.268" diameter. Procedure: Position the fixture and drill a hole the same diameter as the zinc nailin (3/16" or 1/4"). Insert the anchor and tap gently against the fi xture to be fastened. Drive the nail fl ush to the anchor head to expand the anchor. 25

27 Notes 26

28 epost esolutions - Supply Chain innovations are just a click away eportal eshop Job Pack VMI EDI escan Our Technologies Provide easier, faster & more secure working methods n Reduce supply chain costs n Minimize errors n Improve information availability n epullout eformat Visit our website, or contact us to learn more Manufacturing Locations Exeter Plant Lincoln Corporate Center, 41 Dennis Drive, Reading, PA Medina Plant 5201 Portside Drive, Medina, OH Wyomissing Plant 1045 Spring Street, PO Box 6326, Wyomissing, PA Canada Plant 40 Innovation Drive, Dundas, ON L9H 7P3 US Service Centers: Contact Us Toll Free: Toll-free Fax: Northeast: 1045 Spring Street, PO Box 6326, Wyomissing, PA T: Northern Midwest: 500 West 3rd Avenue, Durant, IA T: Toll-free Fax: Southeast: 675 Progress Center Ave., Unit M, Lawrenceville, GA West Coast: 2426 Port Street, West Sacramento, CA F: T: F: T: Toll-free Fax: F: Canada Service Center: Contact Us Toll-Free : Toll-free Fax: Innovation Drive, Dundas, ON L9H 7P3 T: SFS Intec / Printed in USA Technical advice and sales service SFS intec, Inc Division Construction T Spring Street F PO Box 6326 us.construction@sfsintec.biz US-Wyomissing, PA F: F: Technical Changes Reserved April 2016 SFS intec, Inc. - Canada 40 Innovation Drive Dundas, ON L9H 7P3 T ca.info@sfsintec.biz