12' x 8' Chicken Run Plan. Up to 15 chickens

Transcription

1 12' x 8' Chicken Run Plan Up to 15 chickens

2 Disclaimer The information provided here will show you how to build a chicken coop. However, we at howtoplans.org do not claim that the recommended techniques are the only way to accomplish this task. It will be the responsibility of each customer to ensure the application of the correct construction methods and the use of the proper materials. In addition to the selection of the materials, the customer will be responsible for such construction issues as caulking, flashing, gluing, insulating and nailing, for ensuring adequate workmanship in the areas of installation, roofing and weatherproofing, and for any other items that are beyond the control of the designer. The materials mentioned in the plans do not represent an endorsement or recommendation of any particular product. The Responsibility of Users Despite our commitment to presenting accurate information, howtoplans.org is not liable for any errors or omissions appearing in the plans. Furthermore, howtoplans.org will not be liable for any consequential, special, incidental or indirect damages resulting from the use of this information. Our freedom from liability also extends to such issues as the loss of anticipated profits or business opportunities, and economic losses stemming from the use of howtoplans.org, regardless of whether there has been notification of such damage. Liability Those who utilize the methods described on howtoplans.org will be responsible for their own actions. We are not liable for any injuries or property damage that may arise from the use of the information appearing on this website. If you decide to use these plans, you should employ only quality materials and should always adhere to good safety practices. In the event that you are unable to complete the project on your own, you should contact a certified contractor to ensure that construction is completed with the highest standards. Permissions It is important to understand that planning and permission issues are dependent upon local requirements. Users of these plans are responsible for complying with the appropriate statutes and regulations, and for the proper implementation of the plans or other construction information provided by howtoplans.org. The city or county office in your area should be able to provide you with the relevant information. Copyright The text and illustrations that appear here are the exclusive property of howtoplans.org and are protected by federal copyright laws. The duplication, sale or distribution of any portion of these plans without prior written consent from the original designer will be subject to the appropriate penalties for copyright infringement. Sharing this plan on the web is only permited with an indicated original source:

3 Assemble The Bottom Frame Assemble the frame from the beams with cross-section 4 x 4 inch. At the junction, make a sample of half the thickness of the beam and a depth of 4 inches. Connect the beams with 2 x 3 1/2" self-tapping screws for each joint. Clarify that all diagonals are equal. 8' 12'

4 7' 3' 7' 7' 7' Framing The Coop's Walls Install the support pillars of the 7 ft beam with a cross-section of 4 x 4 inches according to the drawing. Secure the beams by means of 4 1/2" x 4 1/2" x 1 1/2" mounting angles and 8x2" self-tapping screws for each joint. 3' 6" 3' 6" 3' 4' 3' 3' 6" 3' 6"

5 Assemble The Top Frame Assemble the frame from the beams with cross-section 4 x 4 inch. At the junction, make a sample of half the thickness of the beam and a depth of 4 inches. Connect the beams with 2 x 3 1/2" self-tapping screws for each joint. Clarify that all diagonals are equal. 8' 12'

6 Installation Of Roof Rafters Fasten the outer rafters with 1 1/2" x 2" x 1 1/2" mounting angle to the top frame, other rafters - with hangers. Use for this 2" self-tapping screws. 3" 3" 3' 5 1/2" 3" 4' 1/2" 3' 6"

7 3' 4' 1 3/ Floor Installation Prepare the 1/2 plywood for the floor according to the drawing. Cut the opening for connection with beams. Secure the plywood by means of 2" self-tapping screws. 1' 7" 3' 6" 1' 7" 3' 6" 3' 6" 8'

8 Corrugated Boards Installation To cover the roof will need 150 ft 2 of corrugated boards. Fasten the boards with 1 1/2" self-tapping screws with a wide head and rubber gaskets specified for corrugated metal boards. After finishing boards installation, put the roof gamble on the top and fasten with 1 1/2" self-tapping screws with a wide head. 3" 12' 11" 3" 5' 6 1/2"

9 Hatching Eggs Case Assemble It is necessary to make two pieces for the right and left wall. Assemble the frame of a beams with a cross section of 2 x 2 inches, according to the drawing. The upper plane has a slope of 9 degrees. Cover the frame with 1/2 plywood from top and bottom sides with help of 2 1/2" selftapping screws. Make partitions of plywood 1/2 inch thick and fasten them to the frame. Prepare the 5 3/8 inch wide siding board for side walls sheathing in the required amount according to the drawing. Cut the shield's top part according to the angle of rafter slope. Assemble siding shields with 2" galvanized nails to the frame beams. Prepare wall's jambs from the beam with a cross-section of 3 x 1/2 inches. Cut the boards at the required angles along the siding contour for the framing. Cover the top plane with a corrugated metal sheet. 1' 8 1/2" 1' 4 1/2" 2' 1/2" 4'

10 Hatching Eggs Case Installation For hatching eggs case fixing, install two mounting angles on required height on the vertical pillars. Secure the hatching eggs bottom on angles with 2" self-tapping screws and back side beams to the pillars with 3 x 6" self-tapping screws. 3'-

11 3 1/ Right Side Wall Installation Prepare the 5 3/8 inch wide siding board for right wall sheathing in the required amount according to the drawing. Assemble siding shields with 2" galvanized nails to the frame beams. Prepare wire mesh for window according to the dimensions. Provide the window frame from the beams with a cross section 2 x 1 inch. Make the inner frame from the beams with a cross section 1 x 1 inch, to connect them together, make a cut in 1/2 depth according to the drawing. Use for this 2" self-tapping screws. 3" 3"

12 Front Door Assemble And Installation It is necessary to make two pieces for the right and left door. Assemble the frame from the beams with cross section 2 x 2 " with self-tapping screws according to the drawing. Prepare the 5 3/8 inch wide siding board for door sheathing in the required amount according to the drawing. Assemble siding shields with 2" galvanized nails to the frame beams. Install door jambs from the beams with cross section 3x1/2" according to the drawing. Install the door assemblies to the frame with the help of two hinges for each door. Put the locks and handles on the both doors. L 3'- 1/ K 1' 8 3/ 1' 8 3/ 1/

13 Aviary's Door Assembly And Installation Assemble the frame from the beams with cross section 3 x 2 inch with 5" self-tapping screws according to the drawing. Install the wire mesh to the back side of the frame with 1" galvanized nails. Install the door assembly to the wall with the help of three hinges on the right side. Put the handle and lock on the right side.

14 7' Aviary's Wire Mesh Installation Prepare wire mesh sheets according to the drawing. To cover all the square will need 175 ft 2 of wire mesh. Fasten the mesh with an industrial stapler. 3' 5" 3' 4' 3' 3' 6"

15 Final Touches Don't forget to choose the desirable paint for your mood and the colors of your yard. Decorate your chicken coop by giving it unique and stylish look.

16 This free plan was brought to you by: For more great HOW-TO plans please visit: Copyright The text and illustrations that appear here are the exclusive property of howtoplans.org and are protected by federal copyright laws. The duplication, sale or distribution of any portion of these plans without prior written consent from the original designer will be subject to the appropriate penalties for copyright infringement. Sharing this plan on the web is only permited with an indicated original source: