European Technical Approval ETA-08/0007

Size: px
Start display at page:

Download "European Technical Approval ETA-08/0007"

Transcription

1 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel Fax Internet Authorised and notified according to Article 10 of the Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products MEMBER OF EOTA European Technical Approval ETA-08/0007 This ETA replaces the previous ETA with the same number and validity from to Trade name: SIMA Beam Shoe type U-I, U-I, U-I, U-I, U-I, U-I, U-I, U-I, U-I and U-I Holder of approval: Sima Industri ApS Industrivej Nord 40 DK-7490 Aulum Tel Fax Internet Generic type and use of construction product: Valid from: to: Manufacturing plant: Three-dimensional nailing plate (Joist hanger for wood to wood connections and wood to concrete or steel connections) Sima Industri ApS Industrivej Nord 40 DK-7490 Aulum This European Technical Approval contains: 58 pages including 2 annexes which form an integral part of the document

2 Page 2 of 58 of European Technical Approval no. ETA-08/0007 I LEGAL BASIS AND GENERAL CONDITIONS 1 This European Technical Approval is issued by ETA-Danmark A/S in accordance with: - Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating to construction products 1), as amended by Council Directive 93/68/EEC of 22 July ). - Bekendtgørelse 559 af (afløser bekendtgørelse 480 af ) om ikrafttræden af EF direktiv af 21. december 1988 om indbyrdes tilnærmelse af medlemsstaternes love og administrative bestemmelser om byggevarer. 5 Reproduction of this European Technical Approval including transmission by electronic means shall be in full. However, partial reproduction can be made with the written consent of ETA-Danmark A/S. In this case partial reproduction has to be designated as such. Texts and drawings of advertising brochures shall not contradict or misuse the European Technical Approval. 6 This European Technical Approval is issued by ETA- Danmark A/S in English. This version corresponds fully to the version circulated within EOTA. Translations into other languages have to be designated as such. - Common Procedural Rules for Requesting, Preparing and the Granting of European Technical Approvals set out in the Annex to Commission Decision 94/23/EC 3). - EOTA Guideline ETAG 015 Three-dimensional nailing plates, September 2002 edition. 2 ETA-Danmark A/S is authorized to check whether the provisions of this European Technical Approval are met. Checking may take place in the manufacturing plant. Nevertheless, the responsibility for the conformity of the products to the European Technical Approval and for their fitness for the intended use remains with the holder of the European Technical Approval. 3 This European Technical Approval is not to be transferred to manufacturers or agents of manufacturers other than those indicated on page 1, or manufacturing plants other than those indicated on page 1 of this European Technical Approval. 4 This European Technical Approval may be withdrawn by ETA-Danmark A/S pursuant to Article 5(1) of Council Directive89/106/EEC. 1) Official Journal of the European Communities N o L40, 11 Feb 1989, p 12. 2) Official Journal of the European Communities N o L220, 30 Aug 1993, p 1. 3) Official Journal of the European Communities N o L 17, 20 Jan 1994, p 34.

3 Page 3 of 58 of European Technical Approval no. ETA-08/0007 II SPECIAL CONDITIONS OF THE EUROPEAN TECHNICAL APPROVAL 1 Definition of product and intended use Definition of the product The Sima Industri A/S Beam Shoe type U-I, U-I, U-I, U-I, U-I, U-I, U-I, U-I and U-I are one-piece, non-welded joist hangers. They are face mounted timberto-timber joist hangers connected to the header beam, the steel member or the concrete structure and the joist with a range of nails or bolts. The joist hangers are made from pre-galvanized steel Grade S 250 GD + Z (min Z275) according to EN 10326:2004. Dimensions, hole positions, steel type and typical installations are shown in Annex A. Intended use The joist hangers are intended for use in making end-grain to side-grain connections in load bearing timber structures, as a connection between a wood based joist and a solid timber or wood based header, where requirements for mechanical resistance and stability and safety in use in the sense of the Essential Requirements 1 and 4 of Council Directive 89/106/EEC shall be fulfilled. They are also intended for use in making an end-grain connection between a timber joist and a concrete structure or a steel member. The joist hangers can be installed as connections between wood based members such as: Structural solid timber ified to C14-C40 according to EN 338 / EN 14081, Glulam ified to GL24-GL36 according to EN 1194 / EN 14080, LVL according to EN 14374, Parallam PSL, Intrallam LSL, Duo- and Triobalken, Layered wood plates, Kreuzbalken with minimum thickness of 80 mm I-beams with backer blocks on both sides of the web in the header and web stiffeners in the joist Plywood according to EN 636 However, the calculation methods are only allowed for a characteristic wood density of up to 350 kg/m 3. Even though the wood based material may have a larger density, this must not be used in the formulas for the load-carrying capacities of the fasteners. Eurocode 5 or a similar national Timber Code. It is assumed that the forces acting on the joist hanger connection are the following and F down as shown in the figure below. The forces and F down shall act in the middle of the joist hanger. It is assumed that the forces are acting right at the end of the joist. Header Nail in joist Centre of grav. It is assumed that the header is prevented from rotating. Similar it is assumed that the concrete structure or the steel member to which the joist hanger is bolted does not rotate. The joist hangers are intended for use for connections subject to static or quasi static loading. The zinc-coated hangers are for use in timber structures subject to dry, internal conditions defined by the service es 1 and 2 of EN :2004, (Eurocode 5). Assumed working life The assumed intended working life of the joist hangers for the intended use is 50 years, provided that they are subject to appropriate use and maintenance. The information on the working life should not be regarded as a guarantee provided by the manufacturer or ETA-Danmark A/S. An assumed intended working life means that it is expected that, when this working life has elapsed, the real working life may be, in normal use conditions, considerably longer without major degradation affecting the essential requirements. B F down Annex B gives the tables for the characteristic load-carrying capacities of the joist hanger connections. The design of the connections shall be in accordance with

4 Page 4 of 58 of European Technical Approval no. ETA-08/ Characteristics of product and assessment ETAG para. Characteristic 2.1 Mechanical resistance and stability*) Assessment of characteristic Characteristic load-carrying capacity See Annex B Stiffness No performance determined Ductility in cyclic testing No performance determined 2.2 Safety in case of fire Reaction to fire The joist hangers are made from steel ified as Euro A1 in accordance with EN and EC decision 96/603/EC, amended by EC Decision 2000/605/EC 2.3 Hygiene, health and the environment Influence on air quality No dangerous materials **) 2.4 Safety in use Not relevant 2.5 Protection against noise Not relevant 2.6 Energy economy and heat retention Not relevant 2.7 Related aspects of serviceability Durability The joist hangers have been assessed as having Serviceability satisfactory durability and serviceability when used in timber structures using the timber species described in Eurocode 5 and subject to the conditions defined by service 1, 2 and Identification See Annex A *) See page 5 of this ETA **) In accordance with In addition to the specific clauses relating to dangerous substances contained in this European Technical Approval, there may be other requirements applicable to the products falling within its scope (e.g. transposed European legislation and national laws, regulations and administrative provisions). In order to meet the provisions of the EU Construction Products Directive, these requirements need also to be complied with, when and where they apply.

5 Page 5 of 58 of European Technical Approval no. ETA-08/0007 Safety principles and partial factors The characteristic load-carrying capacities have been calculated without considering different ratios between the partial factors for timber connections and steel cross sections. Therefore, in the end use calculation based on this ETA, this shall be considered. The values in annex B have been determined by multiplying the calculated resistance of the connection by k mod to consider load duration and service es in accordance with EC 5. Additionally, the capacities indicated for the upward force takes into account the national partial safety factor γ M. No performance has been determined in relation to the joint s stiffness properties - to be used for the analysis of the serviceability limit state. Further, the joist hangers can be fastened to a concrete structure or steel member by bolts with a diameter of, 10 mm in holes with a diameter up to 2 mm larger than the bolt. 2.7 Related aspects of serviceability Corrosion protection in service 1 and 2. In accordance with ETAG 015 the joist hanger have a zinc coating weight of min Z275. The steel employed is S250 GD with min Z275 according to EN 10326: Mechanical resistance and stability See annex B for characteristic load-carrying capacity in the directions F down and. The characteristic capacities of the joist hangers are determined by calculation as described in the EOTA Guideline 015 clause They should be used for designs in accordance with Eurocode 5 or a similar national Timber Code. The design models allow the use of fasteners described in the table on page 15 in Annex A Connector nails in accordance to national approval The load bearing capacities of the joist hangers has been determined based on the use of NKT connector nails 4,0 x 40 mm in accordance with the Danish national approval for the nails. The characteristic withdrawal capacity of the nails has been determined by testing in accordance with EN 1382: Timber structures - Test methods - Withdrawal capacity of timber fasteners: For electroplated zinc covered nails F k fudl = 7, 6 dl (MK-godkendelse 5.50 / 0358) = min 2 2 fhd = 60d The joist hangers are mounted using either full or half nailing. No performance has been determined in relation to ductility of a joint under cyclic testing. The contribution to the performance of structures in seismic zones, therefore, has not been assessed.

6 Page 6 of 58 of European Technical Approval no. ETA-08/ Attestation of Conformity and CE marking 3.1 Attestation of Conformity system The system of attestation of conformity is 2+ described in Council Directive 89/106/EEC (Construction Products Directive) Annex III. a) Tasks for the manufacturer: (1) Factory production control, (2) Initial type testing of the product, b) Tasks for the notified body: 3.2 Responsibilities (1) Initial inspection of the factory and the factory production control, (2) Continuous surveillance Tasks of the manufacturer Factory production control The manufacturer has a factory production control system in the plant and exercises permanent internal control of production. All the elements, requirements and provisions adopted by the manufacturer are documented in a systematic manner in the form of written policies and procedures. This production control system ensures that the product is in conformity with the European Technical Approval. The manufacturer shall only use raw materials supplied with the relevant inspection documents as laid down in the control plan 1. The incoming raw materials shall be subject to controls and tests by the manufacturer before acceptance. Check of materials, such as sheet metal, shall include control of the inspection documents presented by suppliers (comparison with nominal values) by verifying dimension and determining material properties, e.g. chemical composition, mechanical properties and zinc coating thickness. The manufactured components are checked visually and for dimensions. The control plan, which is part of the technical documentation of this European Technical Approval, 1 The control plan has been deposited at the ETA-Danmark A/S and is only made available to the approved bodies involved in the conformity attestation procedure. includes details of the extent, nature and frequency of testing and controls to be performed within the factory production control and has been agreed between the approval holder and ETA-Danmark A/S. The results of factory production control are recorded and evaluated. The records include at least the following information: - Designation of the product, basic material and components; - Type of control or testing; - Date of manufacture of the product and date of testing of the product or basic material and components; - Result of control and testing and, if appropriate, comparison with requirements; - Signature of person responsible for factory production control. The records shall be presented to ETA-Danmark A/S on request Initial type testing of the product For initial type-testing the results of the tests performed as part of the assessment for the European Technical Approval shall be used unless there are changes in the production line or plant. In such cases the necessary initial type testing has to be agreed between ETA-Danmark A/S and the notified body Tasks of notified bodies Initial inspection of the factory and the factory production control The approved body should ascertain that, in accordance with the control plan, the factory, in particular the staff and equipment, and the factory production control, are suitable to ensure a continuous and orderly manufacturing of the joist hangers with the specifications given in part Continuous surveillance The approved body shall visit the factory at least twice a year for routine inspections. It shall be verified that the system of factory production control and the specified manufacturing processes are maintained, taking account of the control plan. The results of product certification and continuous surveillance shall be made available on demand by the certification body to ETA-Danmark A/S. Where the provisions of the European Technical Approval and the control plan are no longer fulfilled, the

7 Page 7 of 58 of European Technical Approval no. ETA-08/0007 certificate of conformity shall be withdrawn by the approved body. 3.3 CE marking The CE marking shall be affixed on each packaging of joist hangers. The initials "CE" shall be followed by the identification number of the notified body and shall be accompanied by the following information: - Name or identifying mark of the manufacturer - The last two digits of the year in which the marking was affixed - the European Technical Approval - Name and size of product - the ETA Guideline (ETAG no. 015) - the EC Certificate of Conformity

8 Page 8 of 58 of European Technical Approval no. ETA-08/ Assumptions under which the fitness of the product for the intended use was favourably assessed 4.1 Manufacturing SIMA Industri Beam Shoe type U-I, U-I, U-I, U-I, U-I, U-I, U-I, U-I, U-I and U-I are manufactured in accordance with the provisions of this European Technical Approval using the manufacturing processes as identified in the inspection of the plant by the notified inspection body and laid down in the technical documentation. 4.2 Installation Joist hanger connections A joist hanger connection is deemed fit for its intended use provided: Header support conditions The header shall be restrained against rotation and be free from wane under the joist hanger. Wood to wood connections Joist hangers can be fastened to wood-based members by nails. There shall be nails in all holes or a partial nailing pattern as prescribed in Annex A can be used. The characteristic capacity of the joist hanger connection is calculated according to the manufacturer s technical documentation, dated The joist hanger connection is designed in accordance with Eurocode 5 or an appropriate national code. The gap between the end of the joist and the surface, where contact stresses can occur during loading shall be limited. This means that for joist hangers with outward flaps shall the gap between the surface of the end of the joist and that of the header be maximum 3 mm. The width of the joist shall be at least the penetration length of the nails, for full nailing and partial nailing without staggering the nails in the joist. For partial nailing with staggered nails in the joist the width shall be at least the penetration length of the nails. The cross section of the joist at the joist hanger connection shall have sharp edges at the lower side against the bottom plate, i.e. it shall be without wane. The cross section of the header shall have a plane surface against the whole joist hanger. The width B J of the joist shall correspond to that of the joist hanger. B J shall not be smaller than B-3 mm, where B is the inner width of the joist hanger. The depth of the joist shall be so large that the top of the joist is at least 20 mm above the upper nail in the joist. Nails to be used shall have a diameter, which fits the holes of the joist hangers. Round nails shall have a diameter which is not smaller than the diameter of the hole minus 1 mm. Wood to concrete or steel The above mentioned rules for wood to wood connections are applicable also for the connection between the joist and the joist hanger. The joist hanger shall be in close contact with the concrete or steel over the whole face. There shall be no intermediate layers in between. The gap between the end of the joist and the surface, where contact stresses can occur during loading shall be limited. This means that the gap between the surface of the end of the joist and that of the concrete or steel shall be maximum 3 mm. The bolt shall have a diameter not less than the hole diameter minus 2 mm. The bolts shall be placed symmetrically about the vertical symmetry line. There shall always be bolts in the 2 upper holes. The upper bolts shall have washers 30x30x3,0 mm. 4.3 Maintenance and repair Maintenance is not required during the assumed intended working life. Should repair prove necessary, it is normal to replace the joist hanger. Thomas Bruun Manager, ETA-Danmark

9 Page 9 of 58 of European Technical Approval no. ETA-08/0007 Annex A Product details and definitions Fastener specification Nail and screw type Nail and screw size (mm) Finish Diameter Length NKT Connector nail 4,0 40 Electroplated zinc Bolt type Bolt size (mm) Finish Diameter Length Bolt M For relevant joist hangers see the assumed characteristic capacities of the bolt connection and compare with the specification of the manufacturer

10 Page 10 of 58 of European Technical Approval no. ETA-08/0007 Joist hanger specification: Holes marked in green are used in case of half nailing Holes marked with green and blue are used in case of full nailing Holes marked with yellow are used for bolts Holes marked with red are never used

11 Page 11 of 58 of European Technical Approval no. ETA-08/0007

12 Page 12 of 58 of European Technical Approval no. ETA-08/0007

13 Page 13 of 58 of European Technical Approval no. ETA-08/0007

14 Page 14 of 58 of European Technical Approval no. ETA-08/0007

15 Page 15 of 58 of European Technical Approval no. ETA-08/0007

16 Page 16 of 58 of European Technical Approval no. ETA-08/0007

17 Page 17 of 58 of European Technical Approval no. ETA-08/0007

18 Page 18 of 58 of European Technical Approval no. ETA-08/0007

19 Page 19 of 58 of European Technical Approval no. ETA-08/0007

20 Page 20 of 58 of European Technical Approval no. ETA-08/0007 Characteristic capacities of the joist hanger connections with nails. The downward and the upward directed forces are assumed to act in the middle of the joist. Two nails patterns are specified. A full nailing pattern, where there are nails in all the holes. A partial nailing pattern, where the number of nails in the joist and the header are at least half the numbers specified for full nailing. The nails in the joist may be staggered and there shall always be a nail in the upper and the lower holes. The other nails are distributed evenly over the height. The nails in the header shall be put in the holes closest to the bend line. The width of the joist shall be at least the penetration length of the nails, for full nailing and partial nailing without staggering the nails in the joist. For partial nailing with staggered nails in the joist the width shall be at least the penetration length of the nails. A.1 Joist hangers with outward and inward flaps and fastened with nails Force downward toward the bottom plate: { n R n R } R Down, k = min J, ef,1 lat, J, k ; H lat, H, k Force upward away from the bottom plate: { n R n R } R Down, k = min J, ef,2 lat, J, k ; H lat, H, k where the following symbols are: n J,ef,1 effective number of nails in the side of the joist n J,ef,2 effective number of nails in the side of the joist n H total number of nails in the side of the header R lat,k characteristic lateral load-carrying capacity of the nails in the joist or in the header indicated by the indices J or H R ax,k characteristic axial load-carrying capacity of the nails in the joist or in the header indicated by the indices J or H A.2 Characteristic capacities of the joist hanger connections with bolts For joist hangers connected to a wall of concrete, lightweight concrete or to a steel member the assumptions for the calculation of the load-carrying capacity of the connection are: The Transfer of force from the joist to the joist hanger is as for a wood-wood connection, se clause A.1. The bolts shall always be positioned symmetrically about the vertical axis of the joist hanger. Washers, 30x30x3 mm shall be installed under the upper 2 bolt heads or nuts

21 Page 21 of 58 of European Technical Approval no. ETA-08/0007 Description of the static model For a downward directed force toward the bottom plate the static behavior is basically the same as for a wood-wood connection with nails or screws. The nails in the joist are subjected to a lateral force, which is equally distributed over all nails or screws in the joist. Since the concrete and steel have a larger compressive strength than timber subjected perpendicular to the grain the rotation point can be assumed positioned at the top of the bottom plate. Washer 30x30x3 mm z max Figure B2 Left: Cross section in joist. Right: The joist will deflect and rotate, at the bottom a contact force will occur at the bottom plate, and the withdrawal forces in the bolts in the wall will vary linearly as assumed for nailed connections in the header. The forces in the bolts will be partly lateral forces, partly withdrawal forces. The lateral forces are distributed evenly over all bolts. The withdrawal forces are on the safe side assumed to be taken by the 2 upper bolts with washers. The maximum withdrawal force in a upper bolt can be calculated from F e F ax, bolt = 2 zmax (A.2.1) where F downward directed force toward the bottom plate e Force Downward, F Nail force Contact force eccentricity = distance from the nail column in the joist to the surface of the header. Z max max distance from upper bolt to the bottom plate (rotation point) The upper 2 bolts are critical. They are subjected to a lateral force and a withdrawal force. The lateral force is determined assuming an even distribution of the downward force F. F lat, bolt = F / nbolt (A.2.2) Characteristic capacities of a bolted joist hanger connection The characteristic capacity of the nail connection between the joist and the joist hanger can be calculated from the same assumptions and formulas as for joist hangers nailed or screwed to a wooden header. = ( n + 2 R (A.2.3) R nail, k J ) lat, J, k The upper 2 bolts are critical. They are subjected to a lateral force calculated from formula (A.2.2). The withdrawal force in an upper bolt is calculated from (A.2.1). where

22 F Page 22 of 58 of European Technical Approval no. ETA-08/0007 downward directed force toward the bottom plate n bolt total number of bolts in the joist hanger e eccentricity = distance from the nail column in the joist to the surface of the header Z max max distance from the upper bolt to the bottom plate (rotation point) It shall be verified by the design of the bolted connection that the upper bolts have sufficient load-carrying design capacity to carry the combined lateral and axial forces. From the characteristic capacity of the bearing resistance between the bolt and the plate of the joist hanger the following maximum characteristic capacity of the joist hanger connection can be determined. where R, k = nbolt fu k dt (A.2.4) bear, n bolt total number of bolts in the 2 flaps f u,k d t characteristic ultimate tensile strength of the steel, 330 MPa diameter of the bolt thickness of the steel plate of the joist hanger The characteristic load-carrying capacity of the joist hanger connections is the minimum of: The capacity determined from (A.2.3) from the nails in the joist The capacity determined from (A.2.4) from the embedding strength of the steel plate against the bolt The capacity controlled by the bolt forces given by (A.2.1) and (A.2.2).

23 Page 23 of 58 of European Technical Approval no. ETA-08/0007 Annex B.1 Characteristic capacities of the downward force F down Beam Shoe 235/65 and 240/65 U Load duration F down in kn P 9,94 L 11,59 Fully nailed Holes marked green and blue 18 M 13,25 S 14,90 I 18,22 The characteristic values found by calculation 16,56 Beam Shoe 235/65 and 240/65 U/I P 6,41 L 7,48 Half nailing Holes marked green 10 M 8,55 S 9,62 I 11,76 The characteristic values found by calculation 10,69

24 Page 24 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 235/65 and 240/65 U / expander bolt Half nailing P 9,60 Holes marked green on the body 4 nails L 11,20 M 12,80 Holes marked yellow 2 bolts S 14,40 I 17,60 The characteristic values found by calculation 16 Beam Shoe 235/65 and 240/65 U / expander bolt Fully nailed P 10,27 Holes marked green and blue 6 nails L 11,98 M 13,69 Holes marked yellow 2 bolts S 15,40 I 18,82 The characteristic values found by calculation 17,11

25 Page 25 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 250/65 U P 13,87 L 16,18 Fully nailed Holes marked green and blue 22 M 18,50 S 20,81 I 25,43 The characteristic values found by calculation 23,12 Beam Shoe 250/65 U/I P 8,55 L 9,98 Half nailing Holes marked green 12 M 11,40 S 12,83 I 15,68 The characteristic values found by calculation 14,25 Beam Shoe 250/65 U / expander bolt Half nailing P 9,60 Holes marked green 4 nails L 11,20 M 12,80 Holes marked yellow 2 bolts S 14,40 I 17,60 The characteristic values found by calculation 16

26 Page 26 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 250/65 U / expander bolt Fully nailed P 13,20 Holes marked green and blue 8 nails L 15,40 M 17,60 Holes marked yellow 2 bolts S 19,80 I 24,20 The characteristic values found by calculation 22 Beam Shoe 260/65 U P 13,87 L 16,18 Fully nailed Holes marked green and blue 22 M 18,50 S 20,81 I 25,43 The characteristic values found by calculation 23,12

27 Page 27 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 260/65 U/I P 8,55 L 9,98 Half nailing Holes marked green 12 M 11,40 S 12,83 I 15,68 The characteristic values found by calculation 14,25 Beam Shoe 260/65 U / antal expander bolt Half nailing P 9,60 Holes marked green 4 nails L 11,20 M 12,80 Holes marked yellow 2 bolts S 14,40 I 17,60 The characteristic values found by calculation 16

28 Page 28 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 260/65 U / expander bolt Fully nailed P 10,27 Holes marked green and blue 8 nails L 11,98 M 13,69 Holes marked yellow 2 bolts S 15,40 I 18,82 The characteristic values found by calculation 17,11 Beam Shoe 320/90 U P 16,01 L 18,68 Fully nailed Holes marked green and blue 28 M 21,35 S 24,02 I 29,36 The characteristic values found by calculation 26,69

29 Page 29 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 320/90 U/I P 10,69 L 12,47 Half nailing Holes marked green 16 M 14,25 S 16,03 I 19,59 The characteristic values found by calculation 17,81 Beam Shoe 320/90 U / expander bolt Half nailing P 11,74 Holes marked green 6 nails L 13,69 M 15,65 Holes marked yellow 4 bolts S 17,60 I 21,52 The characteristic values found by calculation 19,56

30 Page 30 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 320/90 U / expander bolt Fully nailed P 9,94 Holes marked green and blue 10 nails L 11,59 M 13,25 Holes marked yellow 4 bolts S 14,90 I 18,22 The characteristic values found by calculation 16,56 Beam Shoe 380/90 U P 18,15 L 21,18 Fully nailed Holes marked green and blue 36 M 24,20 S 27,23 I 33,28 The characteristic values found by calculation 30,25

31 Page 31 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 380/90 U/I P 12,83 L 14,97 Half nailing Holes marked green 20 M 17,10 S 19,24 I 23,52 The characteristic values found by calculation 21,38 Beam Shoe 380/90 U / expander bolt Half nailing P 13,87 Holes marked green 8 nails L 16,18 M 18,50 Holes marked yellow 2 bolts S 20,81 I 25,43 The characteristic values found by calculation 23,12

32 Page 32 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 380/90 U / expander bolt Fully nailed P 18,15 Holes marked green and blue 12 nails L 21,18 M 24,20 Holes marked yellow 4 bolts S 27,23 I 33,28 The characteristic values found by calculation 30,25 Beam Shoe 380/120 U P 18,15 L 21,18 Fully nailed Holes marked green and blue 33 M 24,20 S 27,23 I 33,28 The characteristic values found by calculation 30,25

33 Page 33 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 380/120 U/I P 12,83 L 14,97 Half nailing Holes marked green 20 M 17,10 S 19,24 I 23,52 The characteristic values found by calculation 21,38 Beam Shoe 380/120 U / expander bolt Half nailing P 9,60 Holes marked green 8 nails L 11,20 M 12,80 Holes marked yellow 4 bolts S 14,40 I 17,60 The characteristic values found by calculation 16

34 Page 34 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 380/120 U / expander bolt Fully nailed P 18,15 Holes marked green and blue 12 nails L 21,18 M 24,20 Holes marked yellow 4 bolts S 27,23 I 33,28 The characteristic values found by calculation 30,25 Beam Shoe 440/130 U P 20,29 L 23,67 Fully nailed Holes marked green and blue 40 M 27,05 S 30,43 I 37,19 The characteristic values found by calculation 33,81

35 Page 35 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 440/130 U/I P 13,87 L 16,18 Half nailing Holes marked green 22 M 18,50 S 20,81 I 25,43 The characteristic values found by calculation 23,12 Beam Shoe 440/130 U / expander bolt Half nailing P 13,87 Holes marked green 8 nails L 16,18 M 18,50 Holes marked yellow 6 bolts S 20,81 I 25,43 The characteristic values found by calculation 23,12

36 Page 36 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 440/130 U / expander bolt Fully nailed P 20,29 Holes marked green and blue 14 nails L 23,67 M 27,05 Holes marked yellow 6 bolts S 30,43 I 37,19 The characteristic values found by calculation 33,81 Beam Shoe 500/155 U P 22,43 L 26,17 Fully nailed Holes marked green and blue 46 M 29,90 S 33,64 I 41,12 The characteristic values found by calculation 37,38

37 Page 37 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 500/155 U/I P 16,01 L 18,68 Half nailing Holes marked green 26 M 21,35 S 24,02 I 29,36 The characteristic values found by calculation 26,69 Beam Shoe 500/155 U / expander bolt Half nailing P 16,01 Holes marked green 10 nails L 18,68 M 21,35 Holes marked yellow 6 bolts S 24,02 I 29,36 The characteristic values found by calculation 26,69

38 Page 38 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 500/155 U / expander bolt Fully nailed P 22,43 Holes marked green and blue 16 nails L 26,17 M 29,90 Holes marked yellow 6 bolts S 33,64 I 41,12 The characteristic values found by calculation 37,38 Beam Shoe 550/155 U P 24,56 L 28,66 Fully nailed Holes marked green and blue 52 M 32,75 S 36,85 I 45,03 The characteristic values found by calculation 40,94

39 Page 39 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 550/155 U/I P 16,01 L 18,68 Half nailing Holes marked green 28 M 21,35 S 24,02 I 29,36 The characteristic values found by calculation 26,69 Beam Shoe 550/155 U / expander bolt Half nailing P 16,01 Holes marked green 10 nails L 18,68 M 21,35 Holes marked yellow 6 bolts S 24,02 I 29,36 The characteristic values found by calculation 26,69

40 Page 40 of 58 of European Technical Approval no. ETA-08/0007 Beam Shoe 550/155 U / Load expander bolt duration F down in kn Fully nailed P 24,56 Holes marked green and blue 18 nails L 28,66 M 32,75 Holes marked yellow 6 bolts S 36,85 I 45,03 The characteristic values found by calculation 40,94

41 Page 41 of 58 of European Technical Approval no. ETA-08/0007 Annex B.2 Characteristic capacities of the downward force F down for beam shoes with outward flaps Beam shoe 235/65 and 240/65 Full nailing: 18 nails P load 2,05 The holes for nailing are marked with 1+2 L load 2,39 M load 2,73 S load 3,07 I load 3,75 Beam shoe 235/65 and 240/65 Half nailing: The holes for nailing are marked with 1 10 nails P load 1,02 L load 1,19 M load 1,36 S load 1,53 I load 1,88

42 Page 42 of 58 of European Technical Approval no. ETA-08/0007 Beam shoe 235/65 and 240/65 Expansion bolt Half nailing: The holes for nailing are marked with 1 Full bolting 4 nails 2 bolts P load 1,02 L load 1,19 M load 1,36 S load 1,53 I load 1,88 Beam shoe 235/65 and 240/65 Expansion bolt Full nailing: 6 nails P load 2,05 The holes for nailing are marked with 1+2 L load 2,39 Full bolting 2 bolts M load 2,73 S load 3,07 I load 3,75

43 Page 43 of 58 of European Technical Approval no. ETA-08/0007 Beam shoe 250/65 Full nailing: 22 nails P load 3,07 The holes for nailing are marked with 1+2 L load 3,58 M load 4,09 S load 4,60 I load 5,63 Beam shoe 250/65 Half nailing: The holes for nailing are marked with 1 12 nails P load 2,05 L load 2,39 M load 2,73 S load 3,07 I load 3,75

44 Page 44 of 58 of European Technical Approval no. ETA-08/0007 Expansion bolt Beam shoe 250/65 Half nailing: The holes for nailing are marked with 1 Full bolting 4 nails 2 bolts P load 2,05 L load 2,39 M load 2,73 S load 3,07 I load 3,75 Expansion bolt Beam shoe 250/65 Full nailing: 8 nails P load 3,07 The holes for nailing are marked with 1+2 L load 3,58 Full bolting 2 bolts M load 4,09 S load 4,60 I load 5,63

45 Page 45 of 58 of European Technical Approval no. ETA-08/0007 Beam shoe 260/65 Full nailing: 22 nails P load 3,07 The holes for nailing are marked with 1+2 L load 3,58 M load 4,09 S load 4,60 I load 5,63 Beam shoe 260/65 Half nailing: The holes for nailing are marked with 1 12 nails P load 2,05 L load 2,39 M load 2,73 S load 3,07 I load 3,75

46 Page 46 of 58 of European Technical Approval no. ETA-08/0007 Expansion bolt Beam shoe 260/65 Half nailing: The holes for nailing are marked with 1 Full bolting 4 nails 2 bolts P load 2,05 L load 2,39 M load 2,73 S load 3,07 I load 3,75 Expansion bolt Beam shoe 260/65 Full nailing: 8 nails P load 3,07 The holes for nailing are marked with 1+2 L load 3,58 Full bolting 2 bolts M load 4,09 S load 4,60 I load 5,63

47 Page 47 of 58 of European Technical Approval no. ETA-08/0007 Beam shoe 320/90 Beam shoe 320/90 Full nailing: 28 nails P load 4,09 The holes for nailing are marked with 1+2 L load 4,78 M load 5,46 S load 6,14 I load 7,50 Beam shoe 320/90 Half nailing: The holes for nailing are marked with 1 16 nails P load 2,05 L load 2,39 M load 2,73 S load 3,07 I load 3,75

48 Page 48 of 58 of European Technical Approval no. ETA-08/0007 Expansion bolt Beam shoe 320/90 Half nailing: The holes for nailing are marked with 1 Full bolting 6 nails 4 bolts P load 2,05 L load 2,39 M load 2,73 S load 3,07 I load 3,75 Expansion bolt Beam shoe 320/90 Full nailing: 10 nails P load 4,09 The holes for nailing are marked with 1+2 L load 4,78 Full bolting 4 bolts M load 5,46 S load 6,14 I load 7,50

49 Page 49 of 58 of European Technical Approval no. ETA-08/0007 Beam shoe 380/90 Full nailing: 36 nails P load 5,12 The holes for nailing are marked with 1+2 L load 5,97 M load 6,82 S load 7,67 I load 9,38 Beam shoe 380/90 Half nailing: The holes for nailing are marked with 1 20 nails P load 3,07 L load 3,58 M load 4,09 S load 4,60 I load 5,63

50 Page 50 of 58 of European Technical Approval no. ETA-08/0007 Expansion bolt Beam shoe 380/90 Half nailing: The holes for nailing are marked with 1 Full bolting 8 nails 4 bolts P load 3,07 L load 3,58 M load 4,09 S load 4,60 I load 5,63 Expansion bolt Beam shoe 380/90 Full nailing: 12 nails P load 5,12 The holes for nailing are marked with 1+2 L load 5,97 Full bolting 4 bolts M load 6,82 S load 7,67 I load 9,38

51 Page 51 of 58 of European Technical Approval no. ETA-08/0007 Beam shoe 380/120 Full nailing: 36 nails P load 5,12 The holes for nailing are marked with 1+2 L load 5,97 M load 6,82 S load 7,67 I load 9,38 Beam shoe 380/120 Half nailing: The holes for nailing are marked with 1 20 nails P load 3,07 L load 3,58 M load 4,09 S load 4,60 I load 5,63

52 Page 52 of 58 of European Technical Approval no. ETA-08/0007 Expansion bolt Beam shoe 380/120 Half nailing: The holes for nailing are marked with 1 Full bolting 8 nails 4 bolts P load 3,07 L load 3,58 M load 4,09 S load 4,60 I load 5,63 Expansion bolt Beam shoe 380/120 Full nailing: 12 nails P load 5,12 The holes for nailing are marked with 1+2 L load 5,97 Full bolting 4 bolts M load 6,82 S load 7,67 I load 9,38

53 Page 53 of 58 of European Technical Approval no. ETA-08/0007 Beam shoe 440/130 Full nailing: 40 nails P load 6,14 The holes for nailing are marked with 1+2 L load 7,16 M load 8,19 S load 9,21 I load 11,26 Beam shoe 440/130 Half nailing: The holes for nailing are marked with 1 22 nails P load 3,07 L load 3,58 M load 4,09 S load 4,60 I load 5,63

54 Page 54 of 58 of European Technical Approval no. ETA-08/0007 Expansion bolt Beam shoe 440/130 Half nailing: The holes for nailing are marked with 1 Full bolting 8 nails 6 bolts P load 3,07 L load 3,58 M load 4,09 S load 4,60 I load 5,63 Expansion bolt Beam shoe 440/130 Full nailing: 14 nails P load 6,14 The holes for nailing are marked with 1+2 L load 7,16 Full bolting 6 bolts M load 8,19 S load 9,21 I load 11,26

55 Page 55 of 58 of European Technical Approval no. ETA-08/0007 Beam shoe 500/155 Full nailing: 46 nails P load 7,16 The holes for nailing are marked with 1+2 L load 8,36 M load 9,55 S load 10,74 I load 13,13 Beam shoe 500/155 Half nailing: The holes for nailing are marked with 1 26 nails P load 7,16 L load 8,36 M load 9,55 S load 10,74 I load 13,13

56 Page 56 of 58 of European Technical Approval no. ETA-08/0007 Expansion bolt Beam shoe 500/155 Half nailing: The holes for nailing are marked with 1 Full bolting 10 nails 6 bolts P load 7,16 L load 8,36 M load 9,55 S load 10,74 I load 13,13 Expansion bolt Beam shoe 500/155 Full nailing: 16 nails P load 7,16 The holes for nailing are marked with 1+2 L load 8,36 Full bolting 6 bolts M load 9,55 S load 10,74 I load 13,13

57 Page 57 of 58 of European Technical Approval no. ETA-08/0007 Beam shoe 550/155 Full nailing: 52 nails P load 9,21 The holes for nailing are marked with 1+2 L load 10,74 M load 12,28 S load 13,81 I load 16,88 Beam shoe 550/155 Half nailing: The holes for nailing are marked with 1 28 nails P load 5,12 L load 5,97 M load 6,82 S load 7,67 I load 9,38

58 Page 58 of 58 of European Technical Approval no. ETA-08/0007 Expansion bolt Beam shoe 550/155 Half nailing: The holes for nailing are marked with 1 Full bolting 10 nails 6 bolts P load 5,12 L load 5,97 M load 6,82 S load 7,67 I load 9,38 Expansion bolt Beam shoe 550/155 Full nailing: 18 nails P load 9,21 The holes for nailing are marked with 1+2 L load 10,74 Full bolting 6 bolts M load 12,28 S load 13,81 I load 16,88

European Technical Approval ETA-07/0212

European Technical Approval ETA-07/0212 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 45 76 20 20 Fax +45 45 76 33 20 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC

More information

European Technical Approval ETA-10/0038

European Technical Approval ETA-10/0038 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC

More information

European Technical Approval ETA-08/0183

European Technical Approval ETA-08/0183 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC

More information

European Technical Approval ETA-08/0165

European Technical Approval ETA-08/0165 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC

More information

European Technical Approval ETA-13/0630

European Technical Approval ETA-13/0630 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC

More information

European Technical Approval ETA-10/0413

European Technical Approval ETA-10/0413 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC

More information

European Technical Assessment ETA-17/1005 of

European Technical Assessment ETA-17/1005 of ETA-Danmark A/S Göteborg Plads 1 DK-2150 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011

More information

European Technical Assessment. ETA-15/0667 of Member of. General part

European Technical Assessment. ETA-15/0667 of Member of. General part INSTITU Schenkenstrasse 4 T +43 1 533 65 50 1010 Vienna Ι Austria F +43 1 533 64 23 www.oib.or.at Ι mail@oib.or.at Designated according to Article 29 of Regulation (EU) No 305/2011 Member of www.eota.eu

More information

European Technical Approval ETA-12/0114

European Technical Approval ETA-12/0114 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC

More information

Österreichisches Institut für Bautechnik Schenkenstrasse Vienna Austria T F

Österreichisches Institut für Bautechnik Schenkenstrasse Vienna Austria T F Authorised and notified according to Article 10 of the Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating

More information

European Technical Assessment ETA-13/0029 of 11/07/2017

European Technical Assessment ETA-13/0029 of 11/07/2017 ETA-Danmark A/S Göteborg Plads 1 DK-2150 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011

More information

European Technical Approval ETA-11/0024

European Technical Approval ETA-11/0024 ETA-Danmark A/S Kollegievej 6 DK-2920 Charlottenlund Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 10 of the Council Directive 89/106/EEC

More information

Verbindungselemente Engel GmbH Weltestraße Weingarten DEUTSCHLAND. Manufacturing plant 74437, , ,

Verbindungselemente Engel GmbH Weltestraße Weingarten DEUTSCHLAND. Manufacturing plant 74437, , , European Technical Assessment ETA-13/0536 of 20 February 2018 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

(English language translation, the original version is in French language) fischer Anchor bolt EXA

(English language translation, the original version is in French language) fischer Anchor bolt EXA Centre Scientifique et Technique du Bâtiment 84, avenue Jean Jaurès CHAMPS SUR MARNE F-77447 Marne-la-Vallée Cedex 2 Tél. : (33) 01 64 68 82 82 Fax : (33) 01 60 05 70 37 Autorisé et notifié conformément

More information

Powers Trak-It XH and HD nails for gas actuated tools C4 and C5

Powers Trak-It XH and HD nails for gas actuated tools C4 and C5 European Technical Assessment ETA-12/0188 of 7 October 2016 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

European Technical Assessment ETA-11/0024 of 08/07/2016

European Technical Assessment ETA-11/0024 of 08/07/2016 ETA-Danmark A/S Göteborg Plads 1 DK-2150 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011

More information

European Technical Assessment ETA-11/0024 of 02/03/2017

European Technical Assessment ETA-11/0024 of 02/03/2017 ETA-Danmark A/S Göteborg Plads 1 DK-2150 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011

More information

European Technical Approval ETA-03/0017

European Technical Approval ETA-03/0017 Deutsches Institut für Bautechnik Anstalt des öffentlichen Rechts Kolonnenstr. 30 L 10829 Berlin Germany Tel.: +49(0)30 787 30 0 Fax: +49(0)30 787 30 320 E-mail: dibt@dibt.de Internet: www.dibt.de Mitglied

More information

(English language translation, the original version is in French language) Simpson Strong-Tie. Universal brackets Purlin anchors Joist anchors

(English language translation, the original version is in French language) Simpson Strong-Tie. Universal brackets Purlin anchors Joist anchors Page 1 technical Approval Centre Scientifique et Technique du Bâtiment 84 avenue Jean Jaurès CHAMPS-SUR-MARNE F-77447 Marne-la-Vallée Cedex 2 Tél. : (33) 01 64 68 82 82 Fax : (33) 01 60 05 70 37 Autorisé

More information

European Technical Assessment. ETA-14/0426 of 15 December English translation prepared by DIBt - Original version in German language

European Technical Assessment. ETA-14/0426 of 15 December English translation prepared by DIBt - Original version in German language European Technical Assessment ETA-14/0426 of 15 December 2014 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

European Technical Assessment ETA-07/0245 of 10/08/2016

European Technical Assessment ETA-07/0245 of 10/08/2016 ETA-Danmark A/S Göteborg Plads 1 DK-21 Nordhavn Tel. +45 72 59 00 Fax +45 72 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 5/11 of the European

More information

European Technical Assessment ETA-04/0038 English translation prepared by DIBt. Page 2 of July 2016

European Technical Assessment ETA-04/0038 English translation prepared by DIBt. Page 2 of July 2016 European Technical Assessment ETA-04/0038 Page 2 of 15 29 July 2016 The European Technical Assessment is issued by the Technical Assessment Body in its official language. Translations of this European

More information

European Technical Assessment. ETA-14/0426 of 21 December English translation prepared by DIBt - Original version in German language

European Technical Assessment. ETA-14/0426 of 21 December English translation prepared by DIBt - Original version in German language European Technical Assessment ETA-14/0426 of 21 December 2016 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

European Technical Assessment ETA-12/0197 of 12/07/2017

European Technical Assessment ETA-12/0197 of 12/07/2017 ETA-Danmark A/S Göteborg Plads 1 DK-2150 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011

More information

European Technical Assessment. ETA-12/0056 of General Part. Technical Assessment Body issuing the ETA:

European Technical Assessment. ETA-12/0056 of General Part. Technical Assessment Body issuing the ETA: Member of SINTEF Building and Infrastructure P.O.Box 124 Blindern NO-0314 Oslo, Norway Phone +47 40 00 51 00 e-mail: certification@sintef.no www.eota.eu European Technical Assessment ETA-12/0056 of 2018-12-15

More information

European Technical Assessment ETA 15/0029 of 12/06/2017

European Technical Assessment ETA 15/0029 of 12/06/2017 RISE Research Institutes of Sweden AB RISE Certifiering Box 553 SE-371 23 Karlskrona Sweden Member of www.eota.eu Tel: +46 10 516 63 00 Web: www.ri.se Mail: certifiering@ri.se European of 12/06/2017 General

More information

European Technical Approval ETA-10/0182

European Technical Approval ETA-10/0182 European Technical Approval English translation prepared by DIBt - Original version in German language Handelsbezeichnung Trade name Zulassungsinhaber Holder of approval Zulassungsgegenstand und Verwendungszweck

More information

Featuring TJ Rim Board and TimberStrand LSL

Featuring TJ Rim Board and TimberStrand LSL #TJ-8000 SPECIFIER S GUIDE TRUS JOIST RIM BOARD Featuring TJ Rim Board and TimberStrand LSL Multiple thicknesses, grades, and products to cover all your rim board needs 1¼" Thickness matches lateral load

More information

European Technical Approval ETA-10/0198

European Technical Approval ETA-10/0198 Deutsches Institut für Bautechnik Anstalt des öffentlichen Rechts Kolonnenstr. 30 B 10829 Berlin Germany Tel.: +49(0)30 787 30 0 Fax: +49(0)30 787 30 320 E-mail: dibt@dibt.de Internet: www.dibt.de Mitglied

More information

FORTRESS BOTTOM PLATE ANCHORS. Product. Scope. Building Regulations. Appraisal No. 687 [2017]

FORTRESS BOTTOM PLATE ANCHORS. Product. Scope. Building Regulations. Appraisal No. 687 [2017] FORTRESS BOTTOM PLATE This Appraisal replaces BRANZ Appraisal No. 687 (2010) BRANZ Appraisals Technical Assessments of products for building and construction. Manufacturing Suppliers Limited 560 Rosebank

More information

ESR-2648 Reissued May 1, 2012 This report is subject to renewal June 1, 2013.

ESR-2648 Reissued May 1, 2012 This report is subject to renewal June 1, 2013. ICC-ES Evaluation Report ESR-2648 Reissued May 1, 2012 This report is subject to renewal June 1, 2013. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council DIVISION:

More information

European Technical Assessment ETA-04/0101 English translation prepared by DIBt. Page 2 of 12 1 March 2018

European Technical Assessment ETA-04/0101 English translation prepared by DIBt. Page 2 of 12 1 March 2018 European Technical Assessment ETA-04/0101 Page 2 of 12 1 March 2018 The European Technical Assessment is issued by the Technical Assessment Body in its official language. Translations of this European

More information

European Technical Assessment. ETA-16/0902 of 17 March English translation prepared by DIBt - Original version in German language.

European Technical Assessment. ETA-16/0902 of 17 March English translation prepared by DIBt - Original version in German language. European Technical Assessment ETA-16/0902 of 17 March 2017 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

VERSA-LAM. An Introduction to VERSA-LAM Products

VERSA-LAM. An Introduction to VERSA-LAM Products 44 VERSA-LAM An Introduction to VERSA-LAM Products VERSA-LAM is one of the strongest and stiffest engineered wood products approved in the UK. 241 302 356 406 VERSA-LAM products are excellent as floor

More information

Instruction Manual for installing

Instruction Manual for installing Instruction Manual for installing Preloaded (HSFG) Bolting with TurnaSure DIRECT TENSION INDICATORS TurnaSure LLC TABLE OF CONTENTS Introduction... 1 Theory of Preloaded Bolting Assemblies... 2 Tightening

More information

Fosroc International Limited Drayton Manor Business Park Coles Road TAMWORTH STAFFORDSHIRE; B78 3XN GROSSBRITANNIEN EAD

Fosroc International Limited Drayton Manor Business Park Coles Road TAMWORTH STAFFORDSHIRE; B78 3XN GROSSBRITANNIEN EAD European Technical Assessment ETA-18/0586 of 12 July 2018 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

European Technical Approval ETA-11/0283

European Technical Approval ETA-11/0283 European Technical Approval ETA-11/0283 - Original version in German language Handelsbezeichnung Trade name Zulassungsinhaber Holder of approval Zulassungsgegenstand und Verwendungszweck Generic type and

More information

ICC-ES Evaluation Report Reissued June 1, 2010 This report is subject to re-examination in one year.

ICC-ES Evaluation Report Reissued June 1, 2010 This report is subject to re-examination in one year. ICC-ES Evaluation Report ESR-2648 Reissued June 1, 2010 This report is subject to re-examination in one year. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Code Council

More information

Timber fasteners for structural use

Timber fasteners for structural use TECHNICAL INFORMATION TIMBER FASTENERS FOR STRUCTURAL USE TESTING AND CERTIFICATION TI-17 V1 Timber fasteners for structural use Testing and certification 01 INTRODUCTION Timber fasteners for structural

More information

CONCEALED HOOK CONNECTORS UV-T / UV-C

CONCEALED HOOK CONNECTORS UV-T / UV-C CONCEALED OOK CONNECTORS / UV-C GEOMETRY Choice of connection system according to the secondary joist cross section SECONDARY JOIST [] SECONDARY JOIST DEPT [] 300 250 200 150 100 50 0 0 200 400 600 800

More information

Instruction Manual for installing

Instruction Manual for installing Instruction Manual for installing Preloaded (HSFG) Bolting with TurnaSure DIRECT TENSION INDICATORS CE Marked EN 14399-9 TurnaSure LLC TABLE OF CONTENTS Introduction... 1 Theory of Preloaded Bolting Assemblies...

More information

European Technical Assessment. ETA-18/0861 of 12 November English translation prepared by DIBt - Original version in German language

European Technical Assessment. ETA-18/0861 of 12 November English translation prepared by DIBt - Original version in German language European Technical Assessment ETA-18/0861 of 12 November 2018 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

DICHIARAZIONE DI PRESTAZIONE ai sensi del regolamento sui prodotti da costruzione (EU) N 305/2011 N : LE_13_0026_IT

DICHIARAZIONE DI PRESTAZIONE ai sensi del regolamento sui prodotti da costruzione (EU) N 305/2011 N : LE_13_0026_IT DICHIARAZIONE DI PRESTAZIONE ai sensi del regolamento sui prodotti da costruzione (EU) N 305/2011 N : LE_13_0026_IT 1. Codice univoco di identificazione del tipo di prodotto 2. Numero di tipo, lotto, serie

More information

STRUCTURAL TIMBER DESIGN

STRUCTURAL TIMBER DESIGN STRUCTURAL TIMBER DESIGN to Eurocode 5 2nd Edition Jack Porteous BSc, MSc, DIC, PhD, CEng, MIStructE, FICE Director lack Porteous Consultancy and Abdy Kernlani BSc, MSc, PhD, CEng, FIStructE, FIWSc Professor

More information

concrete Apolo MEA Befestigungssysteme GmbH Industriestraße Aichach DEUTSCHLAND Apolo MEA Befestigungssysteme GmbH, Plant2 Germany

concrete Apolo MEA Befestigungssysteme GmbH Industriestraße Aichach DEUTSCHLAND Apolo MEA Befestigungssysteme GmbH, Plant2 Germany European Technical Assessment ETA-09/0373 of 1 June 2018 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

Glulam Connection Details

Glulam Connection Details T E C H N I C A L N O T E Glulam Connection Details Note: This version is superseded by a more current edition. Check the current edition for updated design and application recommendations. ENGINEERED

More information

Z January 2017

Z January 2017 Certified True Translation 11 January 2017 I 36-1.14.4-100/16 Z-14.4-776 11 January 2017 30 September 2021 SFS intec GmbH In den Schwarzwiesen 2 61440 Oberursel, Germany Zulassungsnummer = Approval Number

More information

ANCHORING TECHNOLOGY CAST-IN CHANNELS PEC-TA

ANCHORING TECHNOLOGY CAST-IN CHANNELS PEC-TA ANCHORING TECHNOLOGY CAST-IN CHANNELS PEC-TA European Technical Assessment ETA-16/0929 European Technical Assessment ETA-16/0929 of 9 August 2018 - Original version in German language General Part Technical

More information

TRUS JOIST RIM BOARD. Featuring TJ Rim Board and TimberStrand LSL. Multiple thicknesses, grades, and products to cover all your rim board needs

TRUS JOIST RIM BOARD. Featuring TJ Rim Board and TimberStrand LSL. Multiple thicknesses, grades, and products to cover all your rim board needs #TJ-8000 SPECIFIER S GUIDE TRUS JOIST RIM BOARD Featuring TJ Rim Board and Multiple thicknesses, grades, and products to cover all your rim board needs 1¼" Thickness matches lateral load capacity of 2x

More information

APA Performance Rated Rim Boards

APA Performance Rated Rim Boards D a t a F i l e APA Performance Rated Rim Boards A Rim Board is the wood component that fills the space between the sill plate and bottom plate of a wall or, in second floor construction, between the top

More information

THE ENGINEERED WOOD ASSOCIATION

THE ENGINEERED WOOD ASSOCIATION D A T A F I L E APA Performance Rated Rim Boards A rim board is the wood component that fills the space between the sill plate and bottom plate of a wall or, in second floor construction, between the top

More information

ESR-1254 * DELETED BY CITY OF LOS ANGELES. Reissued April 1, 2006 This report is subject to re-examination in one year.

ESR-1254 * DELETED BY CITY OF LOS ANGELES.   Reissued April 1, 2006 This report is subject to re-examination in one year. ESR-1254 Reissued April 1, 2006 This report is subject to re-examination in one year. www.icc-es.org Business/Regional Office 5360 Workman Mill Road, Whittier, California 90601 (562) 699-0543 Regional

More information

HUS 6 Screw anchor, Redundant fastening

HUS 6 Screw anchor, Redundant fastening HUS 6 Screw anchor, Anchor version HUS-A 6 Carbon steel Concrete Screw with hex head HUS-H 6 Carbon steel Concrete Screw with hex head HUS-I 6 Carbon steel Concrete Screw with hex head Benefits - Quick

More information

European Technical Assessment. ETA-09/0338 of 18 June English translation prepared by DIBt - Original version in German language.

European Technical Assessment. ETA-09/0338 of 18 June English translation prepared by DIBt - Original version in German language. European Technical Assessment ETA-09/0338 of 18 June 2018 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

English translation authorized by DIBt Original version in German language

English translation authorized by DIBt Original version in German language Date: Reference: 12/02/2014 I 36-1.14.4-104/13 English translation authorized by DIBt Original version in German language Approval number: Validity Z-14.4-407 from: 1 February 2014 Applicant: IFBS Europark

More information

Klaus-Fischer-Straße Waldachtal DEUTSCHLAND EAD This version replaces ETA-07/0025 issued on 14 May 2018

Klaus-Fischer-Straße Waldachtal DEUTSCHLAND EAD This version replaces ETA-07/0025 issued on 14 May 2018 European Technical Assessment ETA-07/0025 of 28 August 2018 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

Joint Evaluation Report

Joint Evaluation Report 0 Joint Evaluation Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 ESR-2909 Reissued 09/2017 This report is subject to renewal 09/2019. DIVISION: 06 00 00 WOOD, PLASTICS AND COMPOSITES SECTION:

More information

European Technical Assessment. ETA-13/0183 of 29 June English translation prepared by DIBt - Original version in German language.

European Technical Assessment. ETA-13/0183 of 29 June English translation prepared by DIBt - Original version in German language. European Technical Assessment ETA-13/0183 of 29 June 2017 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

ITB TECHNICAL APPROVAL AT /2011

ITB TECHNICAL APPROVAL AT /2011 INSTYTUT TECHNIKI BUDOWLANEJ P L 0 0 6 1 1 W A R S A W, u l. F I L T R O W A 1 Phone: (48 22) 825-04-71; (48 22) 825-76-55; fax (48 22) 825-52-86 M e m b e r o f t h e E u r o p e a n U n i o n o f A g

More information

English translation authorized by DIBt Original version in German language

English translation authorized by DIBt Original version in German language Date: Reference: 29/04/2016 I 36-1.14.1-106/15 English translation authorized by DIBt Original version in German language Approval number: Validity Z-14.1-4 from: 1 February 2016 Applicant: IFBS Europark

More information

GURANTEED TECHNICAL PARTICULARS OF BACK CLAMP FOR LT CROSS ARM

GURANTEED TECHNICAL PARTICULARS OF BACK CLAMP FOR LT CROSS ARM Technical Specification of Back Clamp for LT Cross Arm (MS) Back clamp for LT Cross Arm made out of 50 x 6mm MS Flat suitable for 8m X 300 Kg PSC poles. After fabrication the cross arm shall be painted

More information

LP SolidStart Laminated Strand Lumber (LSL) and Laminated Veneer Lumber (LVL) Louisiana-Pacific Corporation Revised July 21, 2017

LP SolidStart Laminated Strand Lumber (LSL) and Laminated Veneer Lumber (LVL) Louisiana-Pacific Corporation Revised July 21, 2017 LP SolidStart Laminated Strand Lumber (LSL) and Laminated Veneer Lumber (LVL) PR-L280(C) Louisiana-Pacific Corporation Revised July 21, 2017 Products: LP SolidStart 1.35E, 1.55E, and 1.75E LSL LP SolidStart

More information

Dowel-type fasteners. Timber Connections. Academic resources. Introduction. Deferent types of dowel-type fasteners. Version 1

Dowel-type fasteners. Timber Connections. Academic resources. Introduction. Deferent types of dowel-type fasteners. Version 1 Academic resources Timber Connections Dowel-type fasteners Version 1 This unit covers the following topics: Deferent types of dowel-type fasteners Introduction There are four criteria designers should

More information

LOAD CARRYING CAPACITY OF METAL DOWEL TYPE CONNECTIONS OF TIMBER STRUCTURES

LOAD CARRYING CAPACITY OF METAL DOWEL TYPE CONNECTIONS OF TIMBER STRUCTURES Vol. 10, Issue /014, 51-60 DOI: 10.478/cee-014-0011 LOAD CARRYING CAPACITY OF METAL DOWEL TYPE CONNECTIONS OF TIMBER STRUCTURES Jozef GOCÁL 1,* 1 Department of Structures and Bridges, Faculty of Civil

More information

Klaus-Fischer-Straße Waldachtal DEUTSCHLAND EAD This version replaces ETA-15/0352 issued on 12 April 2016

Klaus-Fischer-Straße Waldachtal DEUTSCHLAND EAD This version replaces ETA-15/0352 issued on 12 April 2016 European Technical Assessment ETA-15/0352 of 30 October 2018 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

Statement for nail plate LL13 Combi

Statement for nail plate LL13 Combi STATEMENT NO VTT-S-0369-17 1 (5) Request by Order Contact person Ristek Oy Askonkatu 11 FI-15110 Lahti 15.3.017 Kimmo Köntti VTT Expert Services Ltd Ari Kevarinmäki P.O. Box 1001, FI-0044 VTT Tel. +358

More information

European Technical Assessment. ETA-18/0045 of 22 February English translation prepared by DIBt - Original version in German language

European Technical Assessment. ETA-18/0045 of 22 February English translation prepared by DIBt - Original version in German language European Technical Assessment ETA-18/0045 of 22 February 2018 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Deutsches Institut

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER:

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER: 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2761 Reissued 10/2017 This report is subject to renewal 10/2019. DIVISION: 06 00

More information

ICC-ES Evaluation Report

ICC-ES Evaluation Report ICC-ES Evaluation Report ESR-6 Reissued April, 009 This report is subject to re-examination in two years. www.icc-es.org (800) 4-6587 (56) 699-054 A Subsidiary of the International Code Council DIVISION:

More information

European Technical ETA-17/0513 Assessment of 27 October 2017 General Part

European Technical ETA-17/0513 Assessment of 27 October 2017 General Part European Technical Assessment ETA-17/0513 of 27 October 2017 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

4) Verify that the size of the supporting member can accommodate the connector s specified fasteners.

4) Verify that the size of the supporting member can accommodate the connector s specified fasteners. DESIGN NOTES 1) Allowable loads for more than one direction for a single connection cannot be added together. A design load which can be divided into components in the directions given must be evaluated

More information

ALUMIDI. Concealed beam hanger with and without holes Aluminum alloy tridimensional perforated plate ALUMIDI - 01 CERTIFIED STEEL-ALUMINUM

ALUMIDI. Concealed beam hanger with and without holes Aluminum alloy tridimensional perforated plate ALUMIDI - 01 CERTIFIED STEEL-ALUMINUM ALUMIDI Concealed beam hanger with and without holes Aluminum alloy tridimensional perforated plate CERTIFIED Available with and without holes. The 2200 mm model is also certified FIELD OF USE Timber-to-Timber

More information

Load Tables, Technical Data and Installation Instructions

Load Tables, Technical Data and Installation Instructions W22. W22. W22. W22. W22 W22.. Simpson Strong-Tie Fastening Systems Structural Wood-to-Wood Connections Including Ledgers Designed to provide an easy-to-install, high-strength alternative to through-bolting

More information

JOIST DETAILS Plate nail, 16d (0.15" x 1 ") at 1 on-center Blocking panel: 1 1 8" TJ Rim Board, 1 1 TimberStrand SL or TJI joist Toe nail, 10d (0.11" x ") at on-center A1 CS BEAM DETAILS L1 eb stiffener

More information

European Technical Assessment. ETA-16/0929 of 3 July English translation prepared by DIBt - Original version in German language.

European Technical Assessment. ETA-16/0929 of 3 July English translation prepared by DIBt - Original version in German language. European Technical Assessment ETA-16/0929 of 3 July 2017 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

Introducing AJSTM INSTALLATION GUIDE USA. 8 th Edition USA

Introducing AJSTM INSTALLATION GUIDE USA. 8 th Edition USA The SIMPLE FRAMING SYSTEMSM INSTALLATION GUIDE USA for Floors This Installation Guide is intended to provide general information for the designer and end-user. For further information, please refer to

More information

European Technical ETA-13/1038 Assessment of 26 January 2018 General Part

European Technical ETA-13/1038 Assessment of 26 January 2018 General Part European Technical Assessment ETA-13/1038 of 26 January 2018 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction

More information

DECKS. Stairway illumination Positive attachment of ledger Lateral load connection required board (R507.2) required (R ) (R311.7.

DECKS. Stairway illumination Positive attachment of ledger Lateral load connection required board (R507.2) required (R ) (R311.7. DECKS Max. riser height-7 ¾ Min. tread depth-10 Landings required at (R311.7.5.1) (R311.7.5.2) top and bottom of stairs (R311.7.6) Notched guardrail post NOT allowed Graspable handrail required Spacing

More information

ISO INTERNATIONAL STANDARD. Welding Studs and ceramic ferrules for arc stud welding

ISO INTERNATIONAL STANDARD. Welding Studs and ceramic ferrules for arc stud welding INTERNATIONAL STANDARD ISO 13918 Second edition 2008-02-15 Welding Studs and ceramic ferrules for arc stud welding Soudage Goujons et bagues céramiques pour le soudage à l'arc des goujons Reference number

More information

WELDA FASTENING PLATES

WELDA FASTENING PLATES FASTENING PLATES Author: Markus Junes, M. Sc. Civ. Eng. R&D Manager, Peikko Group 1. INTRODUCTION Peikko Group has launched a new family of Fastening Plate products with resistances calculated on the basis

More information

UV-T Concealed hook connector TIMBER - TIMBER Aluminum three dimensional perforated plate

UV-T Concealed hook connector TIMBER - TIMBER Aluminum three dimensional perforated plate Concealed hook connector TIMER - TIMER Aluminum three dimensional perforated plate COMPLETE RANGE Available in 5 versions, to work with the secondary and load applied. Resistance over 60 kn FIELD OF USE

More information

European Technical Assessment. ETA-12/0373 of Member of. General part

European Technical Assessment. ETA-12/0373 of Member of. General part INSTITU Schenkenstrasse 4 T +43 1 533 65 50 1010 Vienna Ι Austria F +43 1 533 64 23 www.oib.or.at Ι mail@oib.or.at Designated according to Article 29 of Regulation (EU) No 305/2011 Member of www.eota.eu

More information

Bolt Material Types and Grades 1- Bolts made of carbon steel and alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 Nuts made of carbon steel and alloy

Bolt Material Types and Grades 1- Bolts made of carbon steel and alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 Nuts made of carbon steel and alloy Bolt Material Types and Grades 1- Bolts made of carbon steel and alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 Nuts made of carbon steel and alloy steel: 4, 5, 6, 8, 10, 12 2- Bolts made of stainless

More information

Österreichisches Institut für Bautechnik Schenkenstrasse Vienna Austria T F

Österreichisches Institut für Bautechnik Schenkenstrasse Vienna Austria T F Authorised and notified according to Article 10 of the Council Directive 89/106/EEC of 21 December 1988 on the approximation of laws, regulations and administrative provisions of Member States relating

More information

ICC-ES Evaluation Report Reissued March 1, 2011 This report is subject to renewal in two years.

ICC-ES Evaluation Report Reissued March 1, 2011 This report is subject to renewal in two years. ICC-ES Evaluation Report www.icc-es.org (800) -6587 (56) 699-05 ESR-0 Reissued March, 0 This report is subject to renewal in two years. A Subsidiary of the International Code Council DIVISION: 06 00 00

More information

ESR-2403 Reissued October 1, 2009 This report is subject to re-examination in one year.

ESR-2403 Reissued October 1, 2009 This report is subject to re-examination in one year. ICC-ES Evaluation Report ESR-403 Reissued October, 009 This report is subject to re-examination in one year. www.icc-es.org (800) 43-6587 (56) 699-0543 A Subsidiary of the International Code Council DIVISION:

More information

SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS

SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS UDC 621.882.211 [669.14.018.291] IS : 3757-1985 (Reaffirmed 2003) Edition 3.2 (1989-07) Indian Standard SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS ( Second Revision ) (Incorporating Amendment Nos.

More information

SDWH TIMBER-HEX Screw

SDWH TIMBER-HEX Screw Simpson Strong-Tie Fastening Systems Structural Wood-to-Wood Connections, Including Ledgers Double-barrier coating provides corrosion resistance equivalent to hot-dip galvanization, making it suitable

More information

Connection Solutions for Wood-frame Structures. Copyright Materials. Learning Objectives

Connection Solutions for Wood-frame Structures. Copyright Materials. Learning Objectives Connection Solutions for Wood-frame Structures Presented by: John Buddy Showalter, P.E. Vice President, Technology Transfer The Wood Products Council is a Registered Provider with. Credit(s) earned on

More information

Connection and Tension Member Design

Connection and Tension Member Design Connection and Tension Member Design Notation: A = area (net = with holes, bearing = in contact, etc...) Ae = effective net area found from the product of the net area An by the shear lag factor U Ab =

More information

Wood Connections. Concepts of Well Designed Connections

Wood Connections. Concepts of Well Designed Connections Wood Connections Sam Hensen, P.E. Branch Engineering Manager Concepts of Well Designed Connections Must provide sufficient capacity to transfer loads to supporting members Utilize fastener spacing which

More information

Originally Issued: 09/26/2012 Revised: 10/15/2018 Valid Through: 09/30/2019

Originally Issued: 09/26/2012 Revised: 10/15/2018 Valid Through: 09/30/2019 SUNMODO CORPORATION 14800 NE 65 th Street Vancouver, WA 98682 SUNMODO EZ ROOF MOUNT L-FOOT KITS FOR SHINGLE ROOFS CSI Section: 06 25 23 Wood, Plastic, and Composite Fastenings 07 71 00-Roof Specialties

More information

metal anchors fixed on the profile back in combination with special nib bolts Product size covered

metal anchors fixed on the profile back in combination with special nib bolts Product size covered DECLARATION OF PERFORMANCE HALFEN Anchor channel HTA 40/22P and HTA 50/30P CONF-DOP_HTA-P 01/17-E No. H01-16/0453 1. 2. 3. 4. 5. 6. Unique identification code of the HALFEN Anchor channel HTA 40/22P and

More information

Subject of approval: fischer concrete screw ULTRACUT FBS II for the temporary fastening of building site equipment

Subject of approval: fischer concrete screw ULTRACUT FBS II for the temporary fastening of building site equipment Date: Reference: 13 July 2016 I 25-1.21.8-49/15 Approval number: Validity Z-21.8-2049 from: 13 July 2016 Applicant: fischerwerke GmbH & Co. KG Klaus-Fischer-Straße 1 72178 Waldachtal to: 13 July 2021 Subject

More information

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER: SCREW PRODUCTS, INC.

DIVISION: WOOD, PLASTICS AND COMPOSITES SECTION: WOOD, PLASTIC, AND COMPOSITE FASTENINGS REPORT HOLDER: SCREW PRODUCTS, INC. 0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 3654 Reissued 09/2017 This report is subject to renewal 09/2018. DIVISION: 06 00

More information

Connections in CLT Assemblies

Connections in CLT Assemblies Creating forest sector solutions www.fpinnovations.ca Connections in CLT Assemblies Cross Laminated Timber Symposium Vancouver, BC February 8-9, 2011 M. Mohammad Building Systems Wood Products Division

More information

FEATURES APPLICATIONS. Supporting member: Supported member: Technical data sheet AKRX3 - AKRX3

FEATURES APPLICATIONS. Supporting member: Supported member: Technical data sheet AKRX3 - AKRX3 These brackets allow optimum connection between wood and other building materials such as concrete and steel. This is an economic connection that can be used in many areas. AKR AKR-L and vary in the screw

More information

Originally Issued: 06/28/2012 Revised: 06/21/2017 Valid Through: 06/30/ Design

Originally Issued: 06/28/2012 Revised: 06/21/2017 Valid Through: 06/30/ Design EVALUATION SUBJECT: SIMPSON STRONG-DRIVE SDWC WOOD SCREWS REPORT HOLDER: Simpson Strong-Tie Company Inc. 5956 West Las Positas Boulevard Pleasanton, California 94588 (800) 999-5099 www.strongtie.com CSI

More information

LP SolidStart LSL. LP SolidStart LSL Prescriptive Roof Framing Technical Guide 2500F b-1.75e, 2360F b -1.55E and 1730F b -1.

LP SolidStart LSL. LP SolidStart LSL Prescriptive Roof Framing Technical Guide 2500F b-1.75e, 2360F b -1.55E and 1730F b -1. LP SolidStart LSL LP SolidStart LSL Prescriptive Roof Framing Technical Guide 2500F b-1.75e, 2360F b -1.55E and 1730F b -1.35E LSL Please verify availability with the LP SolidStart Engineered Wood Products

More information

NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA

NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA Translated English of Chinese Standard: GB/T18230.1-2000 Translated by: www.chinesestandard.net Wayne Zheng et al. Email: Sales@ChineseStandard.net NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA GB/T

More information