STEEL ANCHOR BASES ALUMINUM ANCHOR BASES
|
|
- Lorin Jenkins
- 6 years ago
- Views:
Transcription
1 max. (Alum.) 20" max. (teel) (ee Note 9) Concrete Foundation Plate 8" x (Typ.) AT-A AT-C Bolt Circle ON TRANFORMER BAE BOTTOM OF BAE (ee Note 8) CONNECTOR 1" 1 " pecial Flat asher Š" - " Tapped Hole for Grounding pecial Flat asher Anchor Bolt 4" Varmint creen (ee Note 7) 1 " x 49" TEEL ANCHOR BAE ALUMINUM TRANFORMER BAE (ee Note 8) TEEL TRANFORMER BAE (ee Note 8) ANCHOR (Note 1) (Note 6) T-A T-C T-B ALUMINUM ANCHOR BAE Note 10 (Note 10) CONNECTOR 1" 1 " 1 " (Varmint creen Required, ee Note 7) (Note 1) (Note 1) Note 10 16" 18" 25" 22" NOTE: 1. For median-mounted poles, Plate and Anchor Bolt dimensions will be modified as indicated on tandard Construction Drawing (CD) HL For pole grounding details see CD HL Breakaway bases shall not be used under pole in excess of manufacturer's rated limits for base. 4. Cast aluminum transformer bases shall not be used where overhead wiring is required. 5. For poles mounted on pilasters on bridge parapets, the anchor bolt shape and length will be modified as indicated in the structure plans. 6. Anchor bolts shall be headed or nutted. L-bends shall not be used. 7. Attach varmint screen with stainless steel band and minimum 2" overlap. Tie overlapping screen with stainless steel wire ties. creen shall be welded wire mesh or expanded metal sheet, stainless steel or galvanized, with openings no larger than ". 8. Aluminum cast transformer bases qualify as breakaway supports. teel transformer bases do not. 9. Per NCHRP Use shims of aluminum for plumbing, or other material if approved by the pole manufacturer. Plumbing tolerance: +/- 1/2 degree. ANCHOR (Note 1) (Note 6) 1 " x 49" 1 " x 60" THI DRAING REPLACE HL DATED TD. TATE OF OHIO DEPARTMENT OF TRANPORTATION ENGINEER O FFICE O F CD NUMBER TANDARD ROADAY CONTRUCTION DRAING PO LE BA E DETAIL RO A D A Y ENGINEERING Duemmel ADMINITRATOR DATE HL
2 max. (Alum.) 20" max. (teel) (ee Note 9) Concrete Foundation Plate 8" x (Typ.) AT-A AT-C Bolt Circle ON TRANFORMER BAE BOTTOM OF BAE (ee Note 8) CONNECTOR 1" pecial Flat asher " - " Tapped Hole for Grounding pecial Flat asher Anchor Bolt 4" ANCHOR Varmint creen (ee Note 7) x 48" TEEL ANCHOR BAE T-A T-C T-B Min. Bolt Circle = haft O. D. at Butt Plus 2.5 Bolt Max. Bolt Circle = CONNECTOR 1" ALUMINUM TRANFORMER BAE (ee Note 8) TEEL TRANFORMER BAE (ee Note 8) ALUMINUM ANCHOR BAE (Varmint creen Required, ee Note 7) Min. Bolt Circle = haft O. D. at Butt Plus 2.5 Bolt Max. Bolt Circle = 16" 18" 25" 22" NOTE: 1. For median-mounted poles, Plate and Anchor Bolt length and shape will be modified as indicated on tandard Construction Drawing (CD) HL For pole grounding details see CD HL Breakaway bases shall not be used under pole in excess of manufacturer s rated limits for base. 4. Cast aluminum transformer bases shall not be used where overhead wiring is required. 5. For poles mounted on pilasters on bridge parapets, the anchor bolt shape and length will be modified as indicated in the structure plans. 6. Anchor bolts shall be headed or nutted. L-bends shall not be used. 7. Attach varmint screen with stainless steel band and minimum 2" overlap. Tie overlapping screen with stainless steel wire ties. creen shall be welded wire mesh or expanded metal sheet, stainless steel or galvanized, with openings no larger than ". 8. Aluminum cast transformer bases qualify as breakaway supports. teel transformer bases do not. 9. Per NCHRP-350. ANCHOR x 48" x 60" THI DRAING REPLACE HL DATED TD. TATE OF OHIO DEPARTMENT OF TRANPORTATION ENGINEER O FFICE O F CD NUMBER TANDARD ROADAY CONTRUCTION DRAING PO LE BA E DETAIL RO A D A Y ENGINEERING Duemmel ADMINITRATOR DATE HL
3 max. (Alum.) 20" max. (teel) (ee Note 9) Concrete Foundation Plate Min. Door 8" x AT-A AT-C Bolt Circle ON TRANFORMER BAE BOTTOM OF BAE (ee Note 8) CONNECTOR 1" pecial Flat asher " - " Tapped Hole for Grounding pecial Flat asher Anchor Bolt 4" ANCHOR Varmint creen (ee Note 7) x 48" TEEL ANCHOR BAE T-A T-C T-B Min. Bolt Circle = haft O. D. at Butt Plus 2.5 Bolt Max. Bolt Circle = CONNECTOR 1" ALUMINUM TRANFORMER BAE (ee Note 8) TEEL TRANFORMER BAE (ee Note 8) ALUMINUM ANCHOR BAE (Varmint creen Required, ee Note 7) Min. Bolt Circle = haft O. D. at Butt Plus 2.5 Bolt Max. Bolt Circle = 16" 18" 25" 22" NOTE: 1. For median-mounted poles, Plate and Anchor Bolt length and shape will be modified as indicated on tandard Construction Drawing (CD) HL For pole grounding details see CD HL Frangible bases shall not be used under pole in excess of manufacturer s rated limits for base. 4. Cast aluminum transformer bases shall not be used where overhead wiring is required. 5. For poles mounted on pilasters on bridge parapets, the anchor bolt shape and length will be modified as indicated in the structure plans " bolts include 4" bend, 48" bolts include a 5" bend, and 60" bolts include a 6" bend. 7. Attach varmint screen with stainless steel band and minimum 2" overlap. Tie overlapping screen with stainless steel wire ties. creen shall be welded wire mesh or expanded metal sheet, stainless steel or galvanized, with openings no larger than ". 8. Aluminum cast transformer bases qualify as breakaway supports. teel transformer bases do not. 9. Per NCHRP-350. ANCHOR x 48" x 60" THI DRAING REPLACE HL DATED TD. TATE OF OHIO DEPARTMENT OF TRANPORTATION ENGINEER O FFICE O F CD NUMBER TANDARD ROADAY CONTRUCTION DRAING PO LE BA E DETAIL RO A D A Y ENGINEERING Duemmel ADMINITRATOR DATE HL
4
5
6
7
8
9
10
5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More information24" B B Joint X501 Joint See MARKINGS Note PCB-RXX-350-TL3 " X501 Y301 (Typ.) " A PLAN (reinforced casting option shown) A " dia. Hinge Bar (Typ.) NOT
B B Joint Joint See MARKINGS Note PCB-RXX-350-TL3 " Y301 (Typ.) " A PLAN (reinforced casting option shown) A " dia. Hinge Bar (Typ.) NOTES GENERAL: This barrier may be manufactured with reinforcing steel
More informationInstallation Instructions
Column & Beam Units with Debris Netting Installation Instructions Laminated Wood Systems, Inc. Seward, Nebraska 800-949-3526 2015 LWS, INC. AVR-NET INSTALL 05-12-16 AVR Installation Notes 1 Safety The
More informationSIGNALS AND LIGHTING FIELD GUIDE
CHAPTER 16 SIGNAL AND LIGHT POLES SIGNAL AND LIGHT POLES The standards and requirements for installing traffic control signal and light poles are presented in this chapter. 16.1 Traffic Control Signal
More informationMAST ARMS & POLES. Ornamental Pole Top & Bases
Ornamental Pole Top & Bases Pelco s decorative pole top and bases make the traffic signal aesthetically pleasing to the eye. In addition to the standar 4-piece, Pelco also manufactures the bases with an
More informationBRIDGE RAILING, 4 TUBE B-26-F POST DETAILS MICHIGAN DEPARTMENT OF TRANSPORTATION
\ ƒ" x 1 " SLOTTED HOLE IN POST AND \ ƒ"! HOLE IN RAIL \ "! x 6" SLOTTED ROUND HEAD BOLTS, WITH 1 PLATE WASHER, 1 LOCK WASHER AND HEX. NUT \ ƒ" x 1 " SLOTTED HOLE IN POST AND \ ƒ"! HOLE IN RAIL \ "! x
More informationGENERAL ISOMETRIC LAYOUT
EXISTING OR PROPOSED WIPER WALL SUPPORT STRUCTURE GATE LID CARBATHAN HG 0 WEB GRAY LOWER PAN GRATING ALUMINUM WIPER WALL CARBATHANE HG, 90 GRAY STRUCTURAL SPECIFICATIONS:. FLOODGATE MATERIAL TO BE ALUMINUM
More informationSIGN MOUNTED BEACON SIG-027-A SINGLE SIGN MOUNTED FLASHING BEACON INSTALLED ON ONE WOOD POST DETAIL "A-1"
1 1/2" x 60" Galvanized (thread both ends) Top Bolt See Detail "A-1" and Slotted Channel Parallel Conduit Clamp Warning Sign 3 Equal Bolt Spacings (3 places at 12" min. spacing) (1) 3/8"x 7" min. (4"x
More informationALUMINUM PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Structural Tube, Pipe and Bar shall be in accordance with ASTM B22 or ASTM B429, Alloy 606-T6. End Rail 90 bends and corner bends with maximum 4-0" post spacing, may be Alloy
More informationHEADED ANCHOR BOLT OPTION
Ground Rod 18" min. Depth, 2 Required nchor Bolts. Number (min. 8) and Size as Required by Manufacturer. 6" to 12" Ground Line " dia. Conduit Number and Direction as Shown on Lighting Layout Sheets. Slope
More informationSTEEL PIPE GUIDERAIL 01/01/
NOTES PIPE RAILING & POSTS: Pipe Rails and s shall be in accordance with ASTM A5 Grade B for standard weight pipe and ASTM A500 Grade B, C or D or ASTM A50 for structural tube. Bars for handrail supports
More informationBaseball Backstopper System
D 8 7 6 5 4 3 2 1 Baseball Backstopper System Cable Design - 4 Poles Layout Form Project Name: Zip Code: A2/A1 = D C B1/A2 = B2/A1 = C A2 POLE A1 POLE B A2/B2 = B1/A1 = B B2 POLE B1 POLE A Please fill
More information(50 FT FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" 8-0" 6-0" Truss Depth. 3" sheets 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.
Column truss connection (See details sheets 3 & 4 of 10) \ Span (Odd number of panels) \ Span (Even number of panels) Back truss chord Top truss chord \ Truss Chord splice Truss depth (See details \ Left
More informationTYPE J (20 FT - 40 FT) MICHIGAN DEPARTMENT OF TRANSPORTATION 10-0" 7-6" NOTE: sheet 5 & 6 of 10) DEPARTMENT DIRECTOR. Kirk T.
Column truss connection Chord splice (see details (See details sheets 3 & 4 of 10) s Top truss chord Free end panel 10-0" Support end panels length varies (See chart below) \ Truss Back truss chord Top
More information2. Remove from the Standard Plate manual: Standard Plate Index, Sheets 1-4 of 4, Numerical Index of Standard Plates (August 31, 2012)
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Program Management & Technical Support, Design Support Section TRANSMITTAL LETTER NO. (12-04) MANUAL: Standard
More informationOne-sided rack, hot-dip galvanized Space between bicycles 350 mm length approx.kg Part-No. Two-sided rack, hot-dip galvanized
Bicycle rack Sturdy and space-saving due to alternating high and low racks. Racks can be bolted to form a serial system, with boreholes for anchoring or plugging. Bicycle parking rack Frame of angular
More informationEdgerail Aluminum Bridge Railing System Specification & Installation Instructions
Edgerail System Specification & Installation Instructions Hill & Smith, Inc 1000 Buckeye Park Road Columbus, Ohio 43207 Tel: 614-340-6294 Fax: 614-340-6296 www.hillandsmith.com Section A System Specification
More informationCurrent Standard Plates including Transmittal Letters are available on the web at:
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Project Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (15-03) MANUAL: Standard
More informationSpring Loaded All Season Roll-Up Doors
Spring Loaded All Season Roll-Up Doors STAND-OFF MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately
More informationMISCELLANEOUS SIGN CONNECTION DETAILS TYPICAL ROUTE MARKER ASSEMBLIES SIGN TO POST MICHIGAN DEPARTMENT OF TRANSPORTATION
5-4" SEE DETAIL I COUPLING BAR ON 3 2-10" CANTILEVER SIGN SUPPORT TYPICAL ROUTE MARKER ASSEMBLIES 5/1 DIAMETER STAINLESS STEEL BOLT AND NYLON INSERT LOCK NUT SELF-ALIGNING STEEL REINFORCING PLATE ( TYPE
More informationOHIO DEPARTMENT OF TRANSPORTATION CENTRAL OFFICE, 1980 W. BROAD ST., COLUMBUS, OHIO
OHIO DEPARTMENT OF TRANSPORTATION CENTRAL OFFICE, 1980 W. BROAD ST., COLUMBUS, OHIO 43216-0899 July 20, 2012 To: Users of the Standard Bridge Drawings From: Tim Keller, Administrator, Office of Structural
More informationEND VIEW WEDGE TOP VIEW WOOD POST FOUNDATION DETAILS
X (NOMINAL POST) 1-1/ DIA. 2 HOLES X 8" (NOMINAL POST) 3-1/ DIA. 2 HOLES TAPERED HARD WOOD WEDGES (HARDWOOD WEDGE TO BE OAK, MAPLE OR OTHER APPROVED DENSE HARDWOODS) TO HOLD POST IN A STABLE POSITION AFTER
More informationSturdi-Wall Design Manual for SW46, SW66, SW63, SW64, SW60, SW83, SW84, and SW80 Models
Sturdi-Wall Design Manual for SW46, SW66, SW63, SW64, SW60, SW83, SW84, and SW80 Models Project Number ME086-05 by Brent Leatherman, P.E. Timber Tech Engineering, Inc E-Mail: bl@timbertecheng.com January
More informationExtra Wide Designer Lockers Series Installation Instructions
Extra Wide Designer Lockers 20000 Series Thank you for selecting the 20000 Series Extra Wide Designer Lockers. We are confident that the quality and construction of the lockers will prove to be a good
More informationTOLL FREE:(888) FAX:(941) ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL
ASSEMBLY of ProTEC CONCRETE STRUCTURAL INSULATED PANEL The ProTEC panels are manufactured with grooves on all four sides to accept the steel components. This grooving applies to the regular panel whose
More information1.1 RELATED DOCUMENTS
SECTION 050505 -BEVEL RAIL ENDS PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the contract, including General and Supplementary Conditions and Division 01 Specification Sections
More informationTREX POST MOUNT DECKING AND CONCRETE
TREX POST MOUNT DECKING AND CONCRETE for Pressure-treated Wood Framing LOCATION AND INSTALLATION OF POST MOUNTS IMPORTANT NOTES:» EACH POST MUST BE ATTACHED AS SHOWN TO ENSURE A CODE COMPLIANT AND SAFE
More informationINSTALLATION SHOP DRAWINGS FOR MINNEAPOLIS, MN
MINNEAPOLIS, MN 2-0- 2-- General Notes Abbreviations Deviations from Architectural Specifications Deviations from Architectural Drawings ALUM. = ALUMINUM B.O. = BY OTHERS CONT. = CONTINUOUS. = CLEARANCE
More informationSpring Loaded SCREEN-PRO. All Season Roll-Up Doors IN-JAMB MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST
Spring Loaded SCREEN-PRO All Season Roll-Up Doors IN-JAMB MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged, immediately
More informationSURVEYOR SURVEYOR + ODOT DESIGN 1 DESIGN 2 RESE T DESIGN 3 DESIGN 4 C/L X MON. CAP DESIGN NAME NAME or COMPANY ODOT o rlpa R/W PS or ODOT o rlpa R/W P
SURVEYOR SURVEYOR + ODOT DESIGN 1 DESIGN 2 RESE T DESIGN 3 DESIGN 4 C/L X MON. CAP DESIGN or COMPANY ODOT o rlpa R/W or ODOT o rlpa R/W NO.00000 NO.00000 or COMPANY NO.00 000 and/or COMPAN Y SURVEYOR SURVEYOR
More information11 6 Round Building Assembly Instructions
11 6 Round Building Assembly Instructions 11 6 Round Building Hardware List 1. Pro Rib Brite White 36 Wide X 68 Long (Siding Steel) 11 2. Top Wall Wheel Ring 3 3. Base Ring 3 4. 1 ½ X 68 Aluminum Tubes
More informationBulk Storage Rack Assembly Instructions
Bulk Storage Rack Assembly Instructions Upright Frame Assembly Determine which end of the post goes up. The keystone slots on the front face of the post are wider at the top than at the bottom (see diagram
More informationMDOTProjectwise\Documents\Reference Documents\Traffic Reference\Statewide Special Details\Develop
500 460 MDOTProjectwise\Documents\Reference Documents\Traffic Reference\Statewide Special Details\Develop Check if Applicable TRAFFIC SIGNAL SPECIAL DETAILS INDEX/CHECKLIST *One completed checklist required
More informationTABLE OF CONTENTS. Impregnated... 1 NORDIC FENCE Fynbo FSC Certified... 1
TABLE OF CONTENTS Impregnated... NORDIC FENCE Fynbo FSC Certified... Iron... NORDIC FENCE Lightweight model, GENERAL... NORDIC FENCE Lightweight model, with a grid filled... NORDIC FENCE Lightweight model,
More informationPART MATERIALS. Section Fencing Materials. Description
PART 03000 - MATERIALS Section 03010 - Fencing Materials Description 03010.00 Scope - This section consists of the test requirements, specifications and tolerances for barbed wire, woven wire and chain
More informationREVIEW ALL INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING INSTALLATION
INSTALLATION INSTRUCTIONS Service Doors, Counter Service Doors & Grilles REVIEW ALL INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING INSTALLATION GENERAL NOTES: Instructions are intended for qualified door mechanics
More informationBol FEATURES: SPECIFICATIONS: 8' 24' Round Tapered and Straight Wood Poles STRUCTURA INC. FIXTURE TYPE: PROJECT NAME:
Bol 8' 24' Round Tapered and Straight Wood Poles FIXTURE TYPE: PROJECT NAME: Round Taper Glulam solid wood and aluminum pole available in 8' 24' lengths. Tenon adapters, slip fitters and side bracket mounts
More informationLENGTH IDENTIFICATION
58 Power-Bolt HEAVY DUTY, ELF-UNDERCUTTING LEEVE TYPE BAE MATERIAL Concrete, Block, Brick, tone IZE RANGE 1/4" x 1" to 1-1/4" x 9 MATERIAL LENGTH IDENTIFICATION The Power-Bolt anchor has a length identification
More informationIn-Tube Motorized SCREEN-PRO. All Season Roll-Up Doors IN-JAMB MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST
In-Tube Motorized SCREEN-PRO All Season Roll-Up Doors IN-JAMB MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged,
More informationTENANT IMPROVEMENT 16 FEBRUARY WEST 27TH STREET, 4TH FLOOR 100% CD OWNER/BID ADD 1-03/08/2018
SECTION 055000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationBioPrism Solid Surface
Please read all instructions before installing products. These instructions are intended for use with InPro s standard toilet partitions, which include 58 high doors and wall panels, when deviating from
More informationAllow 60 from door face
Setbacks Allow 60 from door face TOOLS NEEDED Tape Measure Marker or Pencil Masonry Drill Bit 3/8 Hammer Drill Hammer Socket Wrenches and Wrench: 9/16, 1/2, 7/16, 1/4 drive socket wrench and 1/2 socket
More informationTransmission Line Support Systems
Antenna Support Bracket for transmission line The Antenna Support Bracket angle mounts directly to a 4-1/2" (114 mm) OD antenna pipe mount or tower leg. This is ideal for supporting transmission line runs
More informationSUBJECT: Standard Plates 4132, 4155, Drainage Structures and Castings Info
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Project Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (18-01) MANUAL: Standard
More informationBEST PRACTICE GUIDE. Socket Bases. Working with Concrete Slabs
Working with Concrete Slabs When working with concrete slabs the barrier protection can be erected in three ways - with socket bases, adjustable slab edge brackets and multi slab clamps. Socket Bases 1
More informationExternal Motor Driven SCREEN-PRO. All Season Roll-Up Doors WALL MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST
External Motor Driven SCREEN-PRO All Season Roll-Up Doors WALL MOUNTING METHOD INSTALLATION INSTRUCTIONS READ THIS FIRST Carefully examine the crate(s) for damage before opening. If the carton is damaged,
More informationMH Table of Contents Standard Title/Scope Page Table of Contents SCE Public
MH Table of Contents Standard Title/Scope MH 300 MH 310 MH 318 MH 320 MH 325 MH 330 MH 335 MH 340 MH 350 Manholes Requirements MH 300.1 Manholes Requirements...........................................
More informationINSTALLATION INSTRUCTIONS
SHD TO REMOVE HOOD (SHD) ) LOOSEN (4) SOCKET HEAD SCREWS AND RETAINING RINGS FROM HOOD (SHD). ) REMOVE HOOD AND. 3) DISCONNECT WIRES. 3 4) REMOVE REFLECTOR BY LOOSENING (4) PHILIPS HEAD SCREWS. 5) PLEASE
More informationEUROLINE CLASSIC SOLID SURFACE Installation Instructions
EUROLINE ASSIC SOLID SURFACE Installation Instructions 12/01/15 EUROLINE ASSIC SOLID SURFACE Installation Instructions Before you begin, please note the following considerations: Safety First! Please use
More informationAUXILIARY FRAMING AND ACCESSORIES
CUSTOM CABINETS & RACKS STRUT AND ACCESSO- RIES JUNCTION KITS ANGLE AND BRACE KITS SPLICE KITS BRACE KITS INSTALLATION KITS WALL ANGLE KITS RUBBER END CAPS SUPPORT INSTALLATION AND SUPPORT KITS STANCHION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Special-Lite Restroom Partitions IMPORTANT - BEFORE YOU START... 1. Read through these installation instructions first to understand the order of work. 2. Check all components
More informationMATRIX GUARD. I nstallation I nstructions TERMS AND CONDITIONS. Call or visit
TERMS AND CONDITIONS It is the intent of Wireway Husky Corp. that any product received by our Customers fully meets their expectations. MATRIX GUARD Wireway Husky product is Marketed and Distributed by
More information1.1 SUMMARY. A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards.
PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Loose steel lintels. 2. Shelf angles. 3. Metal floor plate. 4. Pipe bollards. B. See Division 5 Section "Pipe and Tube Railings"
More informationGuardrail T40 4MS2 BP for Bridge Parapet
Guardrail for Bridge Parapet Containment level H2 Installation Manual & Specifications Patented EN 1317 1 SUMMARY A. General description B. Crash testing & CE Certificate C. Working D. Installation method
More informationB-27-A BRIDGE RAILING, 3 TUBE WITH PICKETS SECTION THROUGH RAILING WITH BRUSH BLOCK SECTION THROUGH RAILING WITH SIDEWALK
3" 1'- ƒ " 11 " 7 " TOP OF REAR FLANE TO BE ROUND 2'- LON PICKET 1'- W6 x 25 1 " THICK BASE PLATE " " ELASTOMERIC BOUND FABRIC PAD 8" SLAB DETAIL A (SEE 3) OVERHAN SECTION THROUH RAILIN WITH BRUSH BLOCK
More informationManhole or Catch Basin Type A & B Cone Sections Precast - Design F Manhole or Catch Basin Cover (Reducer Cone Section Precast) Design D
MINNESOTA DEPARTMENT OF TRANSPORTATION DEVELOPED BY: Design Standards ISSUED BY: Office of Program Management and Technical Support, Design Support Section TRANSMITTAL LETTER NO. (14-02) MANUAL: Standard
More information10x12 FOUNDATION GUIDE 10x12 TRICO AND FLORA SHEDS
10x12 FOUNDATION GUIDE 10x12 TRICO AND FLORA SHEDS 10x12 WOOD SKID FLOOR FLOOR SYSTEM FOR 10x12 TRICO AND FLORA SHEDS RAW MATERIALS LIST: 2 (9) FLOOR FRAMING AND SHEATHING: 1) BAND BOARD 2 x 6 x 12 PRESSURE
More informationF-5-1a. Concrete Bollards (Detail 1 of 2) WEIGHT: 166kg. WEIGHT: 227kg. WEIGHT: 113kg. WEIGHT: 212kg
Contents F-5-1a Concrete Bollards F-5-1b Concrete Bollards F-5-2 Concrete Bollards with City Logo F-5-3 Cast Iron Bollards F-5-4 Decorative Steel Bollard F-5-5 Swivel P Gate Steel Bollard F-5-6 Steel Bollard
More informationSTANDARD STALL INSTALLATION DETAIL
14" NOTE: ALUMINUM HEAT SINC STRIP TO BE MOUNTED AT BOTTOM OF PANELS & DOORS. STANDARD STALL INSTALLATION DETAIL ALCOVE WITH ADJOINING STALL INSTALLATION DETAIL ALCOVE INSTALLATION DETAIL C L OF PILASTER
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More informationGENERAL NOTES ABBREVIATIONS DRAWING THEME STRUCTURAL DRAWING LIST SUBMITTALS S101 GENERAL NOTES SOUTH DYKE RIVERFRONT WALKWAY
GENERAL NOTES ABBREVIATIONS DRAWING THEME SUBMITTALS STRUCTURAL DRAWING LIST GENERAL NOTES S0 LETTERS OF ASSURANCE TENDER DOCUMENTS DESIGN BY CONTRACTORS TEMPORARY AND ANCILLARY WORKS AND SITE SAFETY FIELD
More informationBID TABULATION SHEET
Title: Guide Rail & Guide Rail Parts Opening Date: Thursday, January 5, 2017 @ 2:00 pm Contract #: CC-0039-17 Total Bids Received: Signed Proposal Stock Disclose BID TABULATION SHEET Non- Collusion Affirm
More informationRAIL PANEL AT TRANSITION SECTION PLAN - POST DETAIL PLAN - TUBE SPLICE. Colorado Department of Transportation. Staff Bridge Branch
Limits of pay length for Bridge RailType 10M (For post spacing, see Dwg. No. B ) B60610 (Use with B60610A) 8 min. 1 max. 8 min. 1 max. 10 0 Max. 10 0 Max. post spacing 10 0 Max. 2 5 Post 1 x 1 slotted
More information2x Bottom Bracket. 1x Rail Support STEP 1 STEP 2
Level Railing Top Rail Bottom Rail Aluminum Baluster 2x Bottom Bracket 1x Rail Support Kit Includes: 1 - Top Rail (with Baluster Connectors installed) 1 - Bottom Rail (with Baluster Connectors installed)
More informationDouble Beam Freestanding Pergola Installation Guide
Double Beam Freestanding Pergola Installation Guide Patent Pending. Copyright 2011 USAVinyl, LLC - All Rights Reserved The information contained in these instructions are proprietary to USAVinyl, LLC and
More informationCHICKEN COOP & CHICKEN RUN. Tools required for assembly (not included)
CHICKEN COOP & CHICKEN RUN ASSEMBLY MANUAL SKU# 6839 Tools required for assembly (not included) Distributed by: TRACTOR SUPPLY COMPANY 0 VIRGINIA WAY, BRENTWOOD, TN 3707 For customer support, call: -888-376-960
More informationCity of Regina Standard Construction Specification SECTION 2660 CHAIN LINK FENCE
1.0 GENERAL 1.1 Scope 1.1.1 The work shall consist of supply and installing chain link fence, including braces and gates, as shown on the plans and specifications at the locations designated by the Engineer.
More informationFixings & Fastenings. Bright Zinc Plated, Galvanised & Stainless Steel. Lockinex. ea i, ea u i
Fixings & Fastenings Bright Zinc Plated, Galvanised & Stainless Steel Lockinex ea i, ea u i INTRODUCTION The Lockinex Range of Fixings & Fastenings are manufactured in Bright Zinc Plate, Hot dipped galvanised
More informationSIG-032-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY III LUMINAIRE ARM (SEE CONTRACT) 6'-0", 8'-0", 10'-0" NOMINAL SPREAD
Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"
More informationInstallation Instructions
AMPCO Stainless Steel and Baked Enamel Toilet Partitions AMPCO Florida 11400 NW 36 th Avenue Miami, FL 33167 T. 305.821.5700 florida@ampco.com AMPCO Texas 201 Railroad Avenue Sanger, TX 76266 T. 940.458.7401
More informationJVI Vector Connector
The JVI Vector Connector User Guidelines 1 of 11 INTRODUCTION JVI designed the Vector Connector for use as shear and alignment connections between precast concrete elements such as double-tee flanges,
More informationAMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS A. Drawings and General Provisions of Contract, including General and Supplementary Conditions and
More informationSIG-030-B TRAFFIC SIGNAL MAST ARM POLE AND MAST ARM DETAILS - CATEGORY I LUMINAIRE ARM 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) POLE CAP
Michigan Department of Transportation 6'-0", 8'-0", 10'-0" NOMINAL SPREAD (SEE CONTRACT) LUMINAIRE ARM (SEE CONTRACT) POLE CAP 1'-6" (6'-0" ARM) 1'-10" (8'-0" ARM) 2'-0" (10'-0" ARM) NOMINAL RISE 2.38"
More informationM4 Hex Nut [ ] M4 T-Nut 20 [20-044] Appx. 1. 3mm. 20 Series profiles (1 per hole) (1 per hole) Ordering Information
Handles & Light Duty PA 20 1 Assembly of Hinge M4x8 FHCS [24-208-4] M4 T-Nut 20 [20-044] M4 Hex Nut [24-706-4] 60 300-0 PA 20 on panel 2 Hinge positions 3-4 Clearance dimensions 5 Range of swing FOR M4
More informationGENERAL ELEVATION SECTION A-A
NORTH OR WEST Final pavement Elev. m @ roadway 12 352 out to out precast backwall panels Final pavement Elev. m @ roadway SOUTH OR EAST Pile cut-f Elev. m Pile cut-f Elev. m 3:1 3:1 Approx. existing groundline
More informationKwik-Lock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Installation Instructions Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260
INSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260 I. SUSPENDED INSTALLATIONS NOTE: MODEL 260 FENSTEEL TRACK IS ASSEMBLED IN THE SAME MANNER AS DESCRIBED BELOW WITH THE EXCEPTION
More informationUtility Structures. Utility vaults, trenches, transformer pads Electrical Pole Bases and switching cubicles
Utility Structures Utility vaults, trenches, transformer pads Electrical Pole Bases and switching cubicles PRODUCT GUIDE & TECHNICAL REFERENCE MANUAL Providing the right solutions. UTILITY STRUCTURES Perfect
More informationHorizontal Cable Systems
ALUMINUM RAILING INSTALLATION INSTRUCTIONS v2012 orizontal Cable Systems 1) Check Contents Of Packages: Verify that all parts have arrived and that they match the packing list. 1A) Coastal applications:
More informationInstallation Instructions
Installation Instructions 000964 Revision F Installation Instructions for PIRIT Read this manual fully prior to starting installation. Call American eating Customer ervice with any questions. What you
More informationIndex Pipe Hangers and Straps
Index Pipe Hangers and Straps Fig. 1 Standard Clevis Hanger MSS-SP-69, Type 1 WW-H-171E, Type 1 Page 14 Fig. 1CI Clevis Hanger for A.W.W.A. Page 16 Fig. 81 Clevis Hanger WW-H-171E, Type 12 Page 70 Fig.
More informationManholes Table of Contents
Standard MH 300 Title Manholes Requirements MH 300.1 Manholes Requirements Manholes Table of Contents Underground Structures Standards MH 310 MH 318 MH 320 MH 325 MH 330 MH 335 MH 340 MH 350 Precast Tub-Type
More informationSECTION CONCRETE REINFORCEMENT FOR STEAM UTILITY DISTRIBUTION
PAGE 032015-1 SECTION 032015 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
More informationTYPICAL STANDOFF GLASS RAIL ELEVATION TYPICAL SECTION RS0B20 WITH RECTANGULAR BACK PLATE TYPICAL STAIRS
Revisions By: CRL SRS STANDOFF RAILING SYSTEM CRL GLASS RAIL S RS0B20 w/ RECTANGULAR BACK PLATE CRL'S GLASS RAIL S CAN BE USED FOR MOUNTING GLASS PANELS UP TO 3/4" (19 MM) IN THICKNESS. THE 4" X 8" (102
More informationToll-Free
Primary applications for Ross DS Series Security Doors and Frames include government, industrial, commercial and residential properties where protection of people and property is of utmost concern and
More informationSquare Straight Steel - 4 Bolt Base Light Poles
Quick Ship Square Bronze over Galvanized Straight Steel Pole - 4 Bolt Base Square Straight Steel - 4 Bolt Base Light Poles Optional Tenon Mounting (specify) "D" Top Diameter Arm Drilling Per Customer Specs.
More informationFlooring Nails 6-D Flooring Nails $3.40 / 1# 6-D Flooring Nails $14.50 / 5# 8-D Flooring Nails $3.40 / 1# 8-D Flooring Nails $14.
Nails Nails Drywall Screws Common Nails 4D Common Nails $3.85 / 1# 6D Common Nails $3.00 / 1# 6D Common Nails $74.25 / 50# 8D Common Nails $3.00 / 1# 8D Common Nails $74.25 / 50# 10D Common Nails $3.00
More informationInstallation Instructions for 30, 40, and 50 Series Plastic Laminate Toilet Partitions.
GENERAL PARTITIONS Mfg. Corp. 170 Peninsula Drive, Erie PA 16505-443 P.O. Box 8370, Erie, PA 16505-0370 Phone (814) 833-1154 FAX (814) 838-3473 Installation Instructions for 30, 40, and 50 Series Plastic
More informationWAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence
MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised
More information10 x 10 Flat Top Two Tone Pergola
0 x 0 Flat Top Two Tone Pergola Models: Bordeaux ASSEMBLY GUIDE OPTIONAL ACCESSORIES Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post) Bolt Down Bracket Kit ( for Pergola) Ver.0-00
More informationShearwall System Installation Guide
Shearwall System Installation Guide Complete HFX product listing with dimensions, weights, connectors, typical installations and accessories. Also includes Hardy Frame Moment Frame information. Easy as
More informationFoundation Specifications for 5.6-Meter Modular Earth Station Antennas
Installation Instructions Bulletin 237029 Foundation Specifications for 5.6-Meter Modular Earth Station Antennas Revision A Introduction This document specifies typical foundation characteristics, designs,
More informationLateral Support. Decks over 24 above grade require lateral support* *Exceptions to be discussed later
Lateral Support Decks over 24 above grade require lateral support* *Exceptions to be discussed later Decking Types of Decking: -2x4s & 2x6s -five quarter span rated decking boards -Wood plastic composite
More information6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405)
INSTALLATION INSTRUCTIONS FOR BEDSIDE INNER REPAIR PANELS 67-72 GM FLEETSIDES This instruction illustrates the removal and replacement of the often rusted and damaged lower inner flanges on the 1967-1972
More informationTrendWall Floor-To-Ceiling Panels Installation Instruction
TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster
More informationPipe Product Catalog Table of Contents
Pipe Product Catalog Table of Contents Section A: Drawing #: Page Description A1 Reinforced Concrete Pipe A3 Storm Manhole Sizing Chart (48" - 96") A3.1 Storm Manhole Sizing Chart (108" - 144") A4 48"
More informationAluminum frame packing list of Smart Laser CO2
Aluminum frame packing list of Smart Laser CO2 1 805mm V-slot 20mm*40mm 1 2 780mm V-slot 20mm*40mm 2 3 860mm Aluminum frame 20mm*40mm 3 4 177mm Aluminum frame 20mm*40mm 1 5 85mm Aluminum frame 20mm*40mm
More informationFoundation Specifications for 7.6-Meter Modular Earth Station Antennas
Installation Instructions Foundation Specifications for 7.6-Meter Modular Earth Station Antennas Bulletin 237186A Revision A Introduction This document specifies typical foundation characteristics, designs,
More informationAll-O-Matic Jamb-Track Hardware Installation Istructions
All-O-Matic Jamb-Track Hardware Installation Istructions Quality. Performance. All Second To None Service. 1 Types and Sizes Of Jamb Track Hardware Weight Width Height Regular Short Set 350 LBS 19 6 6-7
More informationAdhesive Air Terminal Bases. Universal Surface Bases. Offset Parapet Air Terminal Bases. Section 3.2. Air Terminals & Air Terminal Bases
equipment catalog 3-5 Bases Adhesive Bases Used for mounting on membrane or built-up roofs. Mounted with adhesive or plastic roofing cement. The cast base has a mechanical conductor connector. BS-C-3/8ID-ADH-AT
More information