Braille Repair 101 PRESENTED BY: THE GEORGIA BRAILLE TRANSCRIBERS. The problem with 90% of inoperable braillers is that they need to be cleaned!

Size: px
Start display at page:

Download "Braille Repair 101 PRESENTED BY: THE GEORGIA BRAILLE TRANSCRIBERS. The problem with 90% of inoperable braillers is that they need to be cleaned!"

Transcription

1 Braille Repair 101 PRESENTED BY: THE GEORGIA BRAILLE TRANSCRIBERS The problem with 90% of inoperable braillers is that they need to be cleaned!

2

3 Supplies needed: PERKINS BRAILLER STEP BY STEP CLEANING GUIDE Watch oil Clock oil Lubriplate aero grease ½ inch soft bristle paint brush 1 inch soft bristle paint brush 1 tooth brush with stiff bristles 1 (2 inch) paint brush 1 small artist brush #1 Phillips head screw driver #2 Phillips head screw driver with a minimum shank length of 7 ¾ inches Small flat head screw driver 1 (16x10 inch) clear pan Neutral petroleum based mineral spirit cleaning solvent like kerosene Rubbing alcohol for cleaning the braillers rubber roller A lent free wiping cloth to clean and wipe down the brailler An ice tray to hold and keep the screws separate A small clear cup or glass to hold oil.

4 PERKINS BRAILLER DISASSEMBLING GUIDE Step 1: Turn the brailler upside down and remove the eleven-binding head screws and place them in an ice tray slot. Then, lift off the bottom cover and set it aside. (Use small Phillips head screw driver) Turn the machine back to its normal upright position. To remove the top plate, remove the six assembly screws and place them in the tray in a separate slot from the others. Then, lift the top plate and set it aside. Next, lift out the left paper stop guide assembly and place it in the tray. Also, remove the carriage lever assembly by unscrewing the top screw and any lock washers that are present. Lift and pull the lever towards you and put the screw back in the top to prevent loss. Turn the brailler around with the back facing you and remove the four assembly screws. Place them in a separate slot from the others. Then remove the back plate and set it aside. Now turn the brailler over and use a long Phillips head screwdriver to remove the left or right apron screw and washer. Loosen but don t remove the other screw and washer and gently lift and remove the apron. Turn the brailler to its normal position and remove the frontal plate by removing the two top screws. Place them into the tray separate from the others.

5 PERKINS BRAILLER CLEANING GUIDE Step 2: Dust off loose dirt with a toothbrush and remove any paper bits or foreign objects from the back of the (cam rods) brailler. Turn the brailler towards you and brush the entire machine from top to bottom. Be careful and try to avoid hitting the small springs because they will pop off and you will have trouble putting them back on. Next, turn the brailler upside down and brush the remaining areas of the brailler. To wash the brailler use a shallow 16 x 10 inch pan with the depth of about 1 inch in which the whole brailler should be able to rest easily. Pour about ½ inch cleaning solvent into the pan and set the brailler in the normal upright position with the back of the brailler facing you. Start cleaning the brailler by dipping the 2 inch brush into the solution and start brushing the brailler from top to bottom. Clean the cam rods by placing your hands on all the keys pressing them together to open the cam so you can spread the solution inside the cam. When washing, you may move the carriage assembly to adequately clean the brailller. Turn the brailler around and thoroughly brush the chain and the key slots with the 2 inch brush. With the smaller ½ inch brush, clean the carriage tube. Then, turn the brailler upside down and clean bottom side by cleaning the pawl and back space pawl. Next brush the sides, bottom, and base with the 2 inch brush. Next turn the brailler on its side with the exposed back towards you and move the carriage to the side so you can clean the pawl with the ½ inch brush. Take the back plate and clean the inner parts with the cleaning solvent and wipe it clean with a lent free cloth. Turn the brailler right side up and set atop the pan edges to let drip dry 5 to 10 mins. Once dry, take a lent free cloth or old cotton t-shirt to wipe dry the any remaining solvent left on the brailler. Wipe the cam rods, keys, chain, carriage tube, and carriage beam. Pay close attention to this area s sharp edge, (carriage beam) use the flat head screwdriver with the cloth on top to clean the edges. Check the pan for any loose screws and place them where they belong before putting the brailler back together.

6 PERKINS BRAILLER LUBRICATION GUIDE Step 3: Place the carriage in the center and put the carriage lever back on. Place one drop of watch oil on both sides of the carriage tube and slide the carriage back and forth to spread the oil. Next, pour some clock oil in a cup and use the small artist brush to oil each key slot. Then, press all the keys together numerous times to spread the oil. Next grease the same key slots with the Areo grease and again press all the keys together numerous times to spread the grease. Oil the pivots on both sides with clock oil and move it up and down to work the oil in place. Oil the underside of the sharp beam with clock oil. Oil the chain with clock oil and move the carriage to oil the bottom half of the chain. Oil the drum cam with clock oil. Turn the brailler around and oil the cam rods using clock oil with a medium sized paint brush or a clean toothbrush. Also, open the cam rods and spread the oil and move the carriage to oil missed areas. Turn the brailler upside down and oil each trunnion with clock oil. Then, grease each grooved roller with Aero grease and press the back spacing key to work in the oil and grease. Take the back plate and add a line of clock oil on the iron bar and slide margin stop back and forth to spread the oil. Finally, clean the rubber roller with rubbing alcohol with a lent free cloth and clean the roller free of any grease. Scrub the roller while turning the knob. Do not oil or grease the Line Spacing Pawl, Center Escapement Pawl, nor the Back Spacing Pawl.

7 PERKINS BRAILLER CHECK & REASSEMBLING GUIDE Step 4: Before we put the brailler back together, let s do a few checks to make sure the machine is working properly after cleaning. Put a piece of paper in the machine to check the pawls. First, type some Braille, check the back spacing pawl, and then check the line spacing pawl making sure they operate correctly. Next, then take the paper out. Turn the brailler around so the back is facing you and grab the back plate. Make sure the parts on the back plate move freely back and forth. With the carriage in the center position, put on the back plate making sure you set it atop the visible wire that s protruding from the back. Take two screws and insert one on the top right hand side of the plate and the bottom left side, but don t tighten them to tight. Turn the brailler upside down and move the carriage to the left and then move the right margin as far left as you can and lock it in place. Now, push the spacing bar until it stops at the margin. The margin is set properly when the stationary pawl on the escapement stops in the middle of the teeth having clearance on all sides. If the back plate is not seated correctly then the pawl will not have clearance and will stop and jam the brailler. The proper seating and positioning of the back plate will fix this problem and give clearance to the pawl. Now put in the remaining back plate screws and tighten. To put on the front plate, turn the brailler to its normal position. Remove the carriage lever and line the front plate up over the keys. Drop it in place and add the two front plate screws. Now put on the plastic carriage lever by sliding it on making sure that it s all the way to the back. Now add the screw to the center and push the carriage lever down. Slide the carriage to the right and let the lever up slowly. If the lever is sticking, then the screw is too tight. Now turn the brailler upside down. Connect the apron by connecting the right screw (or left one first) and then tap it into place. Now tighten the screws with the long shank screw driver. Turn the brailler right side up and put a little clock oil in the paper guide slot. Next, grab the paper guide and make sure the washer is at the edge of the paper guide. Make sure the bigger end is facing right. Put on the top plate and add the six screws and tighten.

8 Turn the brailler upside down and put the bottom board back in place. Add the eleven binding head screws back and tighten them. Your Perkins Brailler is clean and ready for use. Also, remember to place the protective covering back on before storing. If the brailler is still not working properly, contact the Georgia Braille Transcribers.

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing

More information

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide The following guidelines should be followed to lubricate the three main parts of the 400QMD mount. The QMD stands for Quartz Micro-Drive controller.

More information

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward.

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward. Figure 1 Miniature Quick Change Applicators, of the end feed type, are designed to crimp end feed strip terminals to prestripped wires. Each applicator is set up to accept the strip form of certain specific

More information

ELECTRIC TOOL CORPORATION

ELECTRIC TOOL CORPORATION Cat. No. -0 / Hex Demolition Hammer Cat. No. 0-0 Spline Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 -9-00 d 000 -9-00 d SpecialTools Require Forcing discs

More information

WARNING: Wear safety goggles at all times when the engine is running and cooling

WARNING: Wear safety goggles at all times when the engine is running and cooling WARNING: Wear safety goggles at all times when the engine is running and cooling Please be safe and enjoy your engine. It is not a child's toy it is a precision machined working model. Never leave Children

More information

Chin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets. Contents

Chin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets. Contents Chin Strap Chin Strap, Sealed Pull Pins and Swing Catch for Fiberglass Helmets Contents BTM-1 1.1 Chin Strap BTM-4 1.2.3.1 Preparation BTM-1 1.1.1 Chin Strap Removal BTM-4 1.2.3.2 Disassembly BTM-1 BTM-2

More information

PEDESTAL OVERHAUL. Some of the tools for a pedestal overhaul. Pedestal work stand

PEDESTAL OVERHAUL. Some of the tools for a pedestal overhaul. Pedestal work stand INTRODUCTION A properly greased labyrinth seal will help prevent dust and water damage to the pedestal bearing oil supply and shaft seal area. Properly greased and oiled pedestals rarely require an overhaul.

More information

Maintenance & Parts list for:

Maintenance & Parts list for: Maintenance & Parts list for: Industrial gun GB 2 Juni 2017 This Maintenance & Parts list for industrial gun is prepared by : Winchester Europe Service V. Parbst & Søn as a comprehensive maintenance guide

More information

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO

SERVICE PARTS LIST. M18 FUEL SAWZALL Reciprocating Saw F56A BULLETIN NO CATALOG NO 47(5x) 46 45 00 44 0 59 43 42 84 51 57 46 47 48 59 83 64 77 48 47(2x) 49(2x) 40 58 See service note on page 5 41 82 51 40 41 42 43 44 45 87 52 27 28 34 57 29 (6x) 60 28 EXAMPLE: Component Parts (Small

More information

Removing and Replacing the Y-truck

Removing and Replacing the Y-truck Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic

More information

HURST COMP STICK KIT DODGE CHARGER, MAGNUM, AND CHRYSLER 300 (with AUTO-STICK) Catalog # & by Hurst Performance

HURST COMP STICK KIT DODGE CHARGER, MAGNUM, AND CHRYSLER 300 (with AUTO-STICK) Catalog # & by Hurst Performance HURST COMP STICK KIT 2005-2007 DODGE CHARGER, MAGNUM, AND CHRYSLER 300 (with AUTO-STICK) Catalog #538 0410 & 538 0411 2009 by Hurst Performance FORM 159 0410 03/09 Thank you for purchasing the Hurst Comp

More information

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades

OPERATIONAL MANUAL V1.0. Removing/Replacing Blades OPERATIONAL MANUAL V1.0 BLUEROCK WS-212 Wire Stripper Removing/Replacing Blades CAUTION!! IMPORTANT!! DANGER!! WARNING!! DISCONNECT MACHINE FROM POWER BEFORE PROCEEDING!! Estimated Completion Time: 90

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)

More information

Volvo 240/260 New Face Overlay Installation Models By Dave Barton

Volvo 240/260 New Face Overlay Installation Models By Dave Barton Volvo 240/260 New Face Overlay Installation 1975-80 Models By Dave Barton These custom faces are the product of years of research and experimentation. They are printed with a special printer using waterproof

More information

HDL(M)6 Nut/Screw Assembly

HDL(M)6 Nut/Screw Assembly HDL(M)6 Nut/Screw Assembly Remove, repair, and reassemble the nut and screw assembly in your HDL series double lock vise. In these instructions when we refer to the front of the vise or nut/screw assembly,

More information

Basic Assembly For Conventional Series 9000 Structural Panels

Basic Assembly For Conventional Series 9000 Structural Panels Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 Basic Assembly For Conventional Series 9000 Structural Panels NOTE: Assembly directions for curved panels are the same as standard panels. Tools

More information

Installation Instructions 8115F 8115SF

Installation Instructions 8115F 8115SF TM Installation Instructions 85F 85SF Single Control Centerset Lavatory Faucet with Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect Drain, a feature

More information

Thomas Scientific Swedesboro, NJ U.S.A.

Thomas Scientific Swedesboro, NJ U.S.A. Thomas Scientific Swedesboro, NJ 08085-0099 U.S.A. Wiley Mini Mill 3383-L10 (115 V, 60 HZ) USE AND CARE OF CATALOG NUMBER: 3383-L10 Wiley Mini Mill (115 V, 60 HZ) PRELIMINARY 1. Mill has been properly

More information

STENCIL MACHINE OPERATION uline.com H-259, H-347 H-408 CUTTING THE OIL BOARD INSERTING THE OIL BOARD

STENCIL MACHINE OPERATION uline.com H-259, H-347 H-408 CUTTING THE OIL BOARD INSERTING THE OIL BOARD H-259, H-347 H-408 π STENCIL MACHINE 1-800-295-5510 uline.com OPERATION NOTE: No assembly is necessary after you unpack your machine. INSERTING THE OIL BOARD 1. Move the release lever to the right. This

More information

Daily Maintenance. 2. Insert bobbin cases in to rotary hooks. Make sure bobbin thread is not over 2 inches long. Close bobbin case covers.

Daily Maintenance. 2. Insert bobbin cases in to rotary hooks. Make sure bobbin thread is not over 2 inches long. Close bobbin case covers. Rotary hook 1. Open bobbin case covers and remove bobbin cases. Use brush to remove lint build up in and around rotary hooks. Compressed air may also be used. Daily Maintenance Cle aning Oiling Rotary

More information

OPERATION AND MAINTENANCE FOR MODEL MRV050A REVERSIBLE

OPERATION AND MAINTENANCE FOR MODEL MRV050A REVERSIBLE OPERATION AND MAINTENANCE FOR MODEL MRV050A REVERSIBLE MANUAL AIR MOTOR 04666770 Edition 1 April, 1999 IMPORTANT SAFETY INFORMATION ENCLOSED. READ THIS MANUAL BEFORE OPERATING TOOL. FAILURE TO OBSERVE

More information

Adjusting, Changing and Maintaining The Latches and Catches on Your Airstream

Adjusting, Changing and Maintaining The Latches and Catches on Your Airstream Adjusting, Changing and Maintaining The Latches and Catches on Your Airstream Hinges,Latches and Catches in your Airstream Bumps, pulling, gravity and time can have an affect on hinges and latches. Adjustments

More information

BY ALIEN TECHNOLOGIES CORP

BY ALIEN TECHNOLOGIES CORP BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support

More information

QB78 CO 2 Pellet Rifle

QB78 CO 2 Pellet Rifle QB78 CO 2 Pellet Rifle Maintenance Instructions Text and photos by George Fox Lang The Chinese QB78 pellet rifle is one of the nicest and most popular CO 2 rifles ever produced. Here are the long-wanted

More information

Ringblaster Mark IV Maintenance Guide. Version 1.5

Ringblaster Mark IV Maintenance Guide. Version 1.5 Ringblaster Mark IV Maintenance Guide Version 1.5 WARNING Winchester Industrial Equipment and Loads must be properly stored, handled and maintained for safe and proper function. Mishandling or failure

More information

Rev B C-RING TOOL VA0375 ½ in. OPERATING MANUAL

Rev B C-RING TOOL VA0375 ½ in. OPERATING MANUAL Rev B 4-30-0 C-RING TOOL VA0375 ½ in. OPERATING MANUAL Operational Instructions for Vertex C-Ring Tool VA0375 Vertex Fasteners is committed to providing our customers with world-class customer service

More information

UNPACKING. Thank you for purchasing the Manual Capsule Filling Machine from KARISHMA PHARMA MACHINES.

UNPACKING. Thank you for purchasing the Manual Capsule Filling Machine from KARISHMA PHARMA MACHINES. UNPACKING Thank you for purchasing the Manual Capsule Filling Machine from KARISHMA PHARMA MACHINES. Please take sufficient time and read this manual carefully before you start installation and operation

More information

Cam Handle Service Guide

Cam Handle Service Guide Cam Handle Service Guide Page 2. Introduction Page 3. Troubleshooting guide Page 4-5. Adjusting the clamp force Page 6-7. Disassembling, greasing and replacing components Page 8-9. Replacing the post bearings

More information

HEAD TUBE BEARINGS. All content copyright AtomicZombie Extreme Machines. All rights reserved. 1

HEAD TUBE BEARINGS. All content copyright AtomicZombie Extreme Machines. All rights reserved. 1 HEAD TUBE BEARINGS This basic tutorial will demonstrate the workings of a typical bicycle threaded head tube set, showing the removal and installation of the various components that make up a head tube

More information

All Terrain Flares 2014 Chevy Silverado

All Terrain Flares 2014 Chevy Silverado Page 1/8 Components: 1. Front Flares (2) 2. Rear Flares (2) Tools required: - Utility knife - #2 Phillips driver - Socket wrench - 13 mm Socket - 6 mm Allen Wrench - T-15 Torx bit - Trim Removal Tool -

More information

The wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist:

The wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist: WICK REPLACEMENT The wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist: Slow to light, hard movement of the wick adjuster knob, kerosene odor

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut

More information

BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms

BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away

More information

Tools needed: Phillips screwdriver, flat blade screwdriver, rubber cement, clean hands.

Tools needed: Phillips screwdriver, flat blade screwdriver, rubber cement, clean hands. Installing the New Face for the Volvo 740 Turbo Vacuum/Boost Gauge INTRODUCTION: These instructions will guide you through the installation of this new face for your existing vacuum/boost gauge. It is

More information

Maintenance Information

Maintenance Information 16601023 Edition 2 January 2014 Air Impact Wrench 2705P1 Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

Fig Remove chain cover plate bolts. Fig Remove hammer member. Fig Loosen set screws at base of 12-tooth sprocket.

Fig Remove chain cover plate bolts. Fig Remove hammer member. Fig Loosen set screws at base of 12-tooth sprocket. Fig. 17.2. Remove chain cover plate bolts. Fig. 17.1. Remove hammer member. Fig. 17.3. Remove chain cover plate. Fig. 17.4. Loosen set screws at base of 12-tooth sprocket. Page 61 Fig. 17.5. Remove socket

More information

MODEL SK61732 COMPRESSOR SERVICE KIT

MODEL SK61732 COMPRESSOR SERVICE KIT MODEL SK61732 COMPRESSOR SERVICE KIT For use on 607 and 617 Model Compressors with.32 Stroke WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use of damaged parts

More information

OPERATIONS MANUAL. Port-O-Slitter

OPERATIONS MANUAL. Port-O-Slitter Tapco Products Company The World Leader in Specialty Tools for the Professional Port-O-Slitter OPERATIONS MANUAL General instructions, set up, accessories and guide to using your portable precision slitting,

More information

TASK: Replace Control Mechanism/Drive End for G71 Supervue/Everglide Vertical headrail

TASK: Replace Control Mechanism/Drive End for G71 Supervue/Everglide Vertical headrail 1. Locate the clear plastic louver stems where louvers are attached. 2. Rotate louvers open. Slide a hard plastic card between the louver and the long side of the louver stem. Push the card and louver

More information

EMO. Service Instruction. created by Frank Weithöner. Table of contents: Special Tools Assembling Mixing Chamber

EMO. Service Instruction. created by Frank Weithöner. Table of contents: Special Tools Assembling Mixing Chamber EMO Service Instruction created by Frank Weithöner Table of contents: - Special Tools Disassembling Mixing Chamber Assembling Mixing Chamber Adjustment Rotor / Level Indicator Unit Temperature Compensating

More information

Quick Set Dovetail Jig

Quick Set Dovetail Jig Quick Set Dovetail Jig FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CALL OUR CUSTOMER SERVICE HELP LINE : 01509 500359 THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE DESIGN OR SPECIFICATION TO THIS PRODUCT

More information

C-RING TOOL VA0278 OPERATING MANUAL

C-RING TOOL VA0278 OPERATING MANUAL C-RING TOOL VA0278 OPERATING MANUAL 1798 Sherwin Avenue Des Plaines, IL 60018 U.S.A. EMAIL: vertex@leggett.com PHONE: 847-768-6139 FAX: 847-768-7192 Operational Instructions for Vertex C-Ring Tool VA0278

More information

Stuff-Your-Stuff Platform Bed (Twin and Full)

Stuff-Your-Stuff Platform Bed (Twin and Full) Stuff-Your-Stuff Platform Bed (Twin and Full) Pre-Assembly: Please read all instructions before beginning assembly. Assembly by two people is a must. Save all packing materials until assembly is complete

More information

Half Door Installation Instructions

Half Door Installation Instructions Half Door Installation Instructions For: CJ5 (1955-1975), CJ6 (All), M38-A1 (1955-1971) Part Number: 53025 WARNING This product is designed primarily to enhance the appearance of the vehicle and to shield

More information

OWNER'S MANUAL Issue 2 - December 14, 2000

OWNER'S MANUAL Issue 2 - December 14, 2000 OWNER'S MANUAL AL Issue 2 - December 14, 2000 Copyright 2000 GAMMA Sports - All Rights Reserved Provided by www.gssalliance.com OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...FEATURES PAGE

More information

OPERATING INSTRUCTIONS www.bowforcearchery.com MAINTENANCE AND FINE TUNING Routinely grease the following with a premium bearing grease: The Extended Nut Fixture using the supplied grease fitting. The

More information

Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-BI30 Binocular Viewing Head

Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-BI30 Binocular Viewing Head Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-BI30 Binocular Viewing Head (Revision 1) Copyright 2017 Carl Hunsinger All rights reserved. This document may not be reproduced or distributed,

More information

Table of Contents. Warranty...3. Attaching your square tubing...4. Your Light Fixture...5. Your Thread Stand...6. Attaching your Laser Light...

Table of Contents. Warranty...3. Attaching your square tubing...4. Your Light Fixture...5. Your Thread Stand...6. Attaching your Laser Light... Owner s Manual Table of Contents Warranty...3 Attaching your square tubing...4 Your Light Fixture...5 Your Thread Stand...6 Attaching your Laser Light...7 What is the Tension Release Lever?...7 Needle

More information

L.L.Bean. Farmhouse Futon

L.L.Bean. Farmhouse Futon L.L.Bean Farmhouse Futon Thank you for purchasing our Farmhouse Futon. Assembly of this product requires a Phillips Head Screwdriver and Flat Head Screwdriver. We have found it helpful to have a second

More information

400GTO Lubrication Guide

400GTO Lubrication Guide 400GTO Lubrication Guide Lubrication Guidelines for the following equatorial mounting: 400GTO Servo with GTOCP2 or CP3 Controller For other 400 models please review other postings as they become available.

More information

Installation and Care Instructions: Rear Windshield - CFMOTO UForce 800

Installation and Care Instructions: Rear Windshield - CFMOTO UForce 800 Installation and Care Instructions: Rear Windshield - CFMOTO UForce 800 *** DO NOT REMOVE PROTECTIVE LAYER FROM THE WINDSHIELD AT THIS TIME. THIS SHOULD BE YOUR LAST AND FINAL INSTALLATION STEP AS WINDSHIELD

More information

SIMPLEX ELITE MAT CUTTER

SIMPLEX ELITE MAT CUTTER INSTRUCTION MANUAL MODEL 750-1 / 760-1 SIMPLEX ELITE MAT CUTTER INSTRUCTIONS AND OPERATION MANUAL 40 in (101 cm) mat cutting system with bevel & straight cutters, production stops, 27 in (68 cm) squaring

More information

Tapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y

Tapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y W8VB The exploded assembly drawing should be used only for authoized service center. W8VB Item No. Part time 1 Magnetic Hex. Socket 2 Sub Stopper 3 O-Ring (S-16) 4 Locator (A) 5 Lock Sleeve (A) 6 O-Ring

More information

Cut-True 16M Manual Paper Cutter

Cut-True 16M Manual Paper Cutter Cut-True 16M Manual Paper Cutter 2/2013 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS TOPIC PAGE Specifications 1 Safety Guidelines 1 Assembly 2 Overview 3 Description of Equipment Parts 3-4 Operation

More information

RIPPER PEDAL. Bearing / Axle Replacement. ( Disassembly )

RIPPER PEDAL. Bearing / Axle Replacement. ( Disassembly ) RIPPER PEDAL Bearing / Axle Replacement ( Disassembly ) 1 1. Use good quality tools to avoid stripping screw sockets. 2. When servicing your pedals, work on one side at a time to prevent parts from mixing

More information

For assembly see instructions in carton

For assembly see instructions in carton 88 5523 943 Kitchen Island IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have

More information

STRINGING MACHINE OWNER'S MANUAL. Copyright 1998 GAMMA Sports - All Rights Reserved

STRINGING MACHINE OWNER'S MANUAL. Copyright 1998 GAMMA Sports - All Rights Reserved 6002 STRINGING MACHINE OWNER'S MANUAL Issue 3 - June 20, 1998 Copyright 1998 GAMMA Sports - All Rights Reserved 6002 OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3... ASSEMBLY

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS MODEL RTA - 4985 Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference.

More information

Written By: Philip Le Riche

Written By: Philip Le Riche HP Photosmart D5160 printer Disassembly This guide covers disassembly in order to ease the cover-open linkage or to remove the main logic board for inspection or maintenance. Disassembly and maintenance

More information

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)

Replacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C) Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the

More information

16 STEEL CABINET HEAVY DUTY

16 STEEL CABINET HEAVY DUTY HEAVY DUTY 16 STEEL CABINET ASSEMBLY INSTRUCTIONS SIX DRAWER BASE CABINET 12-2013 Parts List Part No Description Qty Image SIX DRAWER BASE CABINET Part No Description Qty Image SB-1 Cabinet Body 1 SLD-01

More information

Inventory (Figure 2)

Inventory (Figure 2) MODEL T10127 12" SPIRAL CUTTERHEAD INSTRUCTIONS The Model T10127 indexable insert spiral cutterhead is designed to replace the straightknife cutterhead from the Grizzly jointer Model G0609. The total procedure

More information

SE5a Instrument Board part 2 - rev 1.1

SE5a Instrument Board part 2 - rev 1.1 SE5a Instrument Board part 2 - rev 1.1 Fuel (Petrol) Valve This valve uses two circular name plates, eight brass screws, one black plastic base, copper wire and two black plastic risers. You can pick any

More information

BERKEL 818/919 SERIES Slicer

BERKEL 818/919 SERIES Slicer Hardee s Food Systems, Inc. BERKEL 818/919 SERIES Slicer EQUIP 1601 Slicers October 1, 1994 CALIBRATION EQUIPMENT and TOOLS 10 millimeter Metric Wrench CLEANING SUPPLIES Berkel USDA Authorized Oil Multi-Purpose

More information

Assembly Instructions

Assembly Instructions Assembly Instructions 10 CONTRACTOR TABLE SAW Model No. 351.218330 Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman 31624.00 Draft (10/08/09) UNPACKING The

More information

HANDLING INSTRUCTIONS for DISPENSA VVS

HANDLING INSTRUCTIONS for DISPENSA VVS 04/12/08 Top runner (with Stop point) Top damper Stop point Larder frame Trays or baskets Pull-out larder consist of: Top runner Larder frame Trays or baskets Front panel holder Bottom runner Top damper

More information

Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-TR30 Trinocular Viewing Head

Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-TR30 Trinocular Viewing Head Complete Teardown, Cleaning, and Reassembly of the Olympus BH2-TR30 Trinocular Viewing Head Revision 1 Copyright 2018 Carl Hunsinger All rights reserved. This document may not be reproduced or distributed,

More information

Replacing the Reciprocator on an SWF Multi-head.

Replacing the Reciprocator on an SWF Multi-head. Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the

More information

Kontax Stirling Engines KS90R instructions

Kontax Stirling Engines KS90R instructions Kontax Stirling Engines KS90R instructions This document covers the following: Tools required Parts list Assembly instructions Operating instructions Maintenance Contact details: www.stirlingengine.co.uk

More information

MACHINE QUILTING FRAME

MACHINE QUILTING FRAME MACHINE QUILTING FRAME YOU WILL NEED TO PURCHASE: 5 pieces of 1-1/4 thin wall metal conduit (EMT) cut to your preferred length for the rollers. (Maximum 120 ) DETERMINING YOUR ROLLER LENGTH: Determine

More information

Assembly Instructions

Assembly Instructions P/N 8650/8655 Assembly Instructions NOTE: Your Sherline CNC Cam Grinder is double boxed and secured to a wooden shipping frame. Upon delivery, check the outer box for damage. If the box is damaged, take

More information

Pedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches

Pedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches 88 5549 181 Pedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory FABRIC REAR DOORS (5P) P/N 0SR90-HL4-211B (BLACK) P/N 0SR90-HL4-211C (CAMO) Application SXS1000M5P/M5D Honda Dealer: Please give a copy of these instructions to your

More information

How to operate (folding)

How to operate (folding) How to operate (folding) LEFT HAND STACKING OUTWARD OPENING How to operate (folding) RIGHT HAND STACKING OUTWARD OPENING LOCK BOTH LEVER HANDLE AND FLAT HANDLE UTILISING THE D-HANDLE LOCATED ABOVE THE

More information

EA-04a: Repair McGuire Dock (Lift Roller)

EA-04a: Repair McGuire Dock (Lift Roller) Page 1 of 6 EA-04a: Repair McGuire Dock (Lift Roller) SAFETY FIRST o Follow all Caterpillar facility safety standards when performing this task. o Place orange cones at the entrance to the dock to let

More information

Kontax Stirling Engines KS90S instructions

Kontax Stirling Engines KS90S instructions Kontax Stirling Engines KS90S instructions This document covers the following: Tools required Parts list Assembly instructions Operating instructions Maintenance Contact details: www.stirlingengine.co.uk

More information

The Archer Bow Press OPERATING INSTRUCTIONS Partridge Woods Elk Rapids, MI

The Archer Bow Press OPERATING INSTRUCTIONS Partridge Woods Elk Rapids, MI The Archer Bow Press OPERATING INSTRUCTIONS 8203 Partridge Woods Elk Rapids, MI 49629 www.bowforcearchery.com 1 MAINTENANCE AND FINE TUNING Horizontal Pulling Bar The Horizontal Pulling Bar has a break-in

More information

Revised

Revised Indentify Non-powered panels and separate from Powered panels. Non-powered panel shown at left.. Powered panel shown at left has powerway mounted at factory. Also separate panels by surface type, width

More information

Instruction Manual 2 BLADE CLASSIC. Scan the QR code with a mobile device to view the installation video.

Instruction Manual 2 BLADE CLASSIC.  Scan the QR code with a mobile device to view the installation video. Instruction Manual 2 BLADE CLASSIC Scan the QR code with a mobile device to view the installation video. www.max-prop.com 1) INTRODUCTION: Thank you for having chosen a MAX PROP automatic feathering propeller

More information

LX1 Maintenance Manual for Model LX1B. Table of Contents 1. GENERAL DISASSEMBLY, ASSEMBLY AND ADJUSTMENT COMPONENTS...

LX1 Maintenance Manual for Model LX1B. Table of Contents 1. GENERAL DISASSEMBLY, ASSEMBLY AND ADJUSTMENT COMPONENTS... KTI KITO Technical Information LX1 Maintenance Manual for Model LX1B LX1-1.1.2 1 / 14 Edition: D 03.06 Table of Contents 1. GENERAL...2 2. DISASSEMBLY, ASSEMBLY AND ADJUSTMENT...2 3. COMPONENTS...3 4.

More information

MODEL H " BYRD SHELIX CUTTERHEAD INSTRUCTIONS

MODEL H  BYRD SHELIX CUTTERHEAD INSTRUCTIONS MODEL H9291 12" BYRD SHELIX CUTTERHEAD INSTRUCTIONS The Model H9291 12" Byrd Shelix cutterhead is designed to replace the straight-knife cutterhead on the Grizzly jointer Model G0609. The total procedure

More information

40 & 50 Foot PS-1 Box Car Assembly Instructions

40 & 50 Foot PS-1 Box Car Assembly Instructions 40 & 50 Foot PS-1 Box Car Instructions Push the #2100 coupler/stirrup assembly onto the ends of the metal floor. Slide them into the slots and slightly lift the ends (wings), then press firmly on the front

More information

R2C Performance Products 7550 Industrial Drive Forest Park, IL Ph: (708)

R2C Performance Products 7550 Industrial Drive Forest Park, IL Ph: (708) Congratulations on your purchase of the finest Sprint Car Filter and stack sealing system available. This system has been designed for unparalleled ease of assembly, disassembly and cleaning while providing

More information

SERVICE MANUAL. For the Vermont Castings. Please place picture here. MODELS: 2181 (Small) 2183 (Large) 2184 (Extra Large)

SERVICE MANUAL. For the Vermont Castings. Please place picture here. MODELS: 2181 (Small) 2183 (Large) 2184 (Extra Large) SERVICE MANUAL For the Vermont Castings Please place picture here. 1990-1993 DUTCHWEST CONVECTION HEATERS MODELS: 2181 (Small) 2183 (Large) 2184 (Extra Large) HISTORY OF CHANGES 1990 1993 DUTCHWEST CONVECTION

More information

Colonial Classic Bar

Colonial Classic Bar 88 5528 991 Colonial Classic Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts.

More information

Bed Extension Kit 16 Instructions

Bed Extension Kit 16 Instructions The premier source of tooling, parts, and accessories for bench top machinists. Bed Extension Kit 16 Instructions This kit converts a 7 10, 7 12, and 7 14 mini lathe manufactured by SIEG (including those

More information

Owner s Manual For Sit Down

Owner s Manual For Sit Down Owner s Manual For Sit Down Table of Contents Warranty...3 Attaching your square tubing...4 Your Light Fixture...5 Your Thread Stand...6 What is the Tension Release Lever?...7 How Do I Adjust the Height

More information

Explorer Wiring Kit (assembled)

Explorer Wiring Kit (assembled) Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers

More information

RTI TECHNOLOGIES, INC.

RTI TECHNOLOGIES, INC. RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally

More information

COLOR LASERJET PRO MFP. Repair Manual

COLOR LASERJET PRO MFP. Repair Manual OK COLOR LASERJET PRO MFP Repair Manual X M76 M77 HP Color LaserJet Pro MFP M76, M77 Repair Manual Copyright and License 03 Copyright Hewlett-Packard Development Company, L.P. Reproduction, adaptation,

More information

Steele TV Stand Stock # BH

Steele TV Stand Stock # BH LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store

More information

Lumber Smith. Assembly Manual. If you are having problems assembling the saw and need assistance, please contact us at:

Lumber Smith. Assembly Manual. If you are having problems assembling the saw and need assistance, please contact us at: Lumber Smith Assembly Manual If you are having problems assembling the saw and need assistance, please contact us at: 804-577-7398 info@lumbersmith.com 1 Step 1 Safety Carefully read the Owners Manual.

More information

Removing Right-Side. Components. Right-Side. Components. Click Here to Go Back AT THIS POINT

Removing Right-Side. Components. Right-Side. Components. Click Here to Go Back AT THIS POINT Click Here to Go Back NOTE: There is an oil passage beneath the driven gear/drive gear assembly. This passage should be plugged prior to removing the driven gear and drive gear. Failure to do so could

More information

Sewing Machine Maintenance

Sewing Machine Maintenance Sewing Machine Maintenance Guide C-102 Revised by Wendy Hamilton 1 Introduction A well-made sewing machine traditional or serger, new or old, used often or only occasionally will sew perfectly for many

More information

Cleaning your painting tools

Cleaning your painting tools Take care of your tools and your tools will help take care of your house Leading Innovation in Home Improvement www.rdproduct.com Cleaning your painting tools It s a dirty job but somebody has got to do

More information

WOLF PUP LOOM TM & WOLF PUP LT LOOM TM

WOLF PUP LOOM TM & WOLF PUP LT LOOM TM WOLF PUP LOOM TM & WOLF PUP LT LOOM TM Assembly Instructions FL3000 FL3006 FL3009 WOLF PUP WOLF PUP LT Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212

More information

4.4 PUMP MAINTENANCE MODELS: DB, DC, DF, DG, DJ, DL

4.4 PUMP MAINTENANCE MODELS: DB, DC, DF, DG, DJ, DL 4.4 PUMP MAINTENANCE MODELS: DB, DC, DF, DG, DJ, DL 4.4.1 EXPLODED VIEW DRAWING REF. QTY. DB DC DF DG DJ DL DESCRIPTION PART # 1 1 ADAPTOR FRAME 034007 2 12 LOCK WASHER 3/8 x 1/8 S.S. 034004 3 12 HEX HEAD

More information

MODEL 402 PORTA-NAILER For Tongue and Groove Solid Wood & Hardwood Laminate Flooring

MODEL 402 PORTA-NAILER For Tongue and Groove Solid Wood & Hardwood Laminate Flooring ACCESSORIES cont d. Cat. No. 42626 Angled Shoe Base for Nailing 3/4 Flooring over 3/4 Plywood over Concrete OWNER S MANUAL MODEL 402 PORTA-NAILER For Tongue and Groove Solid Wood & Hardwood Laminate Flooring

More information

SUPER PRO GUN & SUPER PRO GUN II

SUPER PRO GUN & SUPER PRO GUN II MAGNUM VENUS PRODUCTS Maintenance & Repair Manual Part No. M6707-1-1 Revision 04.14.01 Maintenance & Repair Corporate HQ & Mfg. Phone: (727) 573-2955 Fax: (727) 571-3636 Email: info@magind.com Web: www.magind.com

More information

12mm (Max) 6mm (Max) 82mm (Max) 12mm (Max) 6mm (Max)

12mm (Max) 6mm (Max) 82mm (Max) 12mm (Max) 6mm (Max) 1 1 2 2 3 3 82mm (Max) 12mm (Max) 12mm (Max) 6mm (Max) 4 4 5 6 8 6mm (Max) 0.5 0mm 1 5 6 7 7 8 9 9 A = B 10 11 12 D B 1 13 14 15 0 C A D E 16 17 18 F G D B N H J G I K 19 A 20 G L 21 C K 1mm L M 1mm 22

More information