Accessory Planer Stand and Roller Extension Tables

Transcription

1 ccessory Planer Stand and Roller xtension Tables Planer Stand shown with elta Model C Planer INSTRUCTION MNUL T PRT NO Copyright 2000 elta Machinery MCHINRY

2 INTROUCTION This manual illustrates the stand with roller extension tables assembled to a elta C Planer. The accessory heavy-duty steel planer stand not only gives a stable support surface for the 15 planer, but is equipped with two roller extension tables that provide added work support and prevent sniping of the wood when planing longer workpieces. ach table features four (4) large 2-1/4 diameter rollers which will allow smoother, easier infeed and outfeed operations. UNPCKING N CLNING Your 15 planer stand with roller extension tables is shipped in one container. Carefully remove the protective coating from the machined surfaces of the extension tables. This coating may be removed with a soft cloth moistened with kerosene. O NOT US CTON, GSOLIN OR LCQUR THINNR OR THIS PURPOS. igure 2, illustrates the components of the stand. igure 3 illustrates the components of the roller extension tables. 1. Side Supports (2) 2. Upper Stand Support rackets (2) 1 3. Lower Stand Support rackets (2) 4. 5/16-18 x 3/4 Carriage Head Screws (16) 5. M8 lat Washers (16) /16-18 Hex Nuts (16) 7. M8 x 30MM Hex Head Screws (4) 8. M8 lange Nuts (4) M8.1 Lockwashers (4) ig Stand Supports (2) Roller xtension Tables (2) 12. 1/4-20 x 3/4 Hex Head Screws (6) 13. 1/4 lat Washers (8) 14. 1/4-20 Hex Nuts (2) 15. M6 x 20 Hex lange Screws (6) 16. M6 lange Nuts (6) 17. Clips (2) 18. Leg Support ig. 3 2

3 SSMLING STN 1. ssemble the two longer support brackets () ig. 4, one of which is shown, to the inside of end panels () with eight 5/16-18 x 3/4 carriage head screws (C), flat washers, and 5/16-18 hex nuts. O NOT COMPLTLY TIGHTN HRWR T THIS TIM. 2. ssemble the two shorter support brackets () ig. 4, to the inside top of end panels () with the remaining eight 5/16-18 x 3/4 carriage head screws (C), flat washers and 5/16-18 hex nuts. O NOT COMPLTLY TIGHTN HRWR T THIS TIM. NOT: Make certain the top lip of support brackets () are positioned under the top lips of end panels () as shown in ig. 4. C ig. 4 SSMLING PLNR TO STN 1. Carefully lift the planer () ig. 5, onto the stand () as shown. CUTION: XTRM CR SHOUL TKN WHN LITING TH PLNR ONTO TH STN S TH CUTTRH KNIVS R XTRMLY SHRP N TH PLNR IS VRY HVY. I IT IS NOT ON MCHNICLLY, MINIMUM O OUR POPL R RQUIR TO MNULLY LIT TH MCHIN. 2. lign the four holes in the bottom of the planer () ig. 5, with the mounting holes in the top of stand (), and mount the planer to the stand with four M8 x 30MM hex head screws () ig. 5, lockwashers and flange nuts. NOT: Screws () ig. 6, one of which is shown, are started upward from the inside of stand (). Later planer models may not need flange nuts. ig Once the planer is assembled to the stand, push down on top of the planer so the legs of the stand adjust to the floor surface. Tighten all stand mounting hardware. ig. 6 3

4 SSMLING SUPPORT RCKTS TO ROLLR XTNSION TLS 1. Place extension table () ig. 7, on a firm supporting surface. lign ends of support assembly () ig. 7, with slotted holes (C) at both sides of extension table (), and fasten support bracket assembly to extension table with two 1/4-20 x 3/4 hex head screws and flat washers (). IMPORTNT: In the position shown in ig. 7, make certain the longer side of notches () will be closest to hinge () of support table. 2. ssemble the remaining support bracket to other extension table in the same manner. C ig. 7 SSMLING ROLLR XTNSION TLS TO PLNR N STN 1. ssemble bracket clips () and leg support () ig. 8, to the front and rear lower stand brackets (), one of which is shown assembled, with two 1/4-20 x 3/4 hex head screws (C), four flat washers () and two 1/4-20 hex nuts (). djustment to height of clip can be made later. C ig lign the three holes in the hinge of extension table (G) ig. 9, with three holes in the front of the planer base (H) and loosely fasten the extension table to the planer as shown with three M6 x 20MM hex flange screws (K) and flange nuts. NOT: Only finger tighten the three screws at this time as height adjustment to the table will be necessary as explained later in STP 4. Later planer models may not need flange nuts. G K K H 3. Place the notches at the bottom of extension table support () ig. 10, so the longer edge of the support rests on the ledge of bottom support bracket (L) as shown. djust bracket clip () so it contacts the horizontal support bar (M). Tighten screw (N) after adjustment is made. NOT: Clip () acts as a safety device so the extension table will not fall accidentally during operation of the planer. ssemble the remaining roller extension table to the rear of the planer in the same manner. ig. 9 M L N 4 ig. 10

5 P G ig. 11 ig IMPORTNT: Make certain the rollers on the extension tables are level with the table surface of the planer. This will provide maximum work support and prevent sniping of the wood being planed. 5. Place a straight edge (P) ig. 11, on the table surface and extending out of the entire surface of the table extension rollers as shown. lign the two surfaces and carefully tighten three screws (K) ig. 9, that are holding the extension table to the base of the planer. Readjust bracket clip () if necessary. 6. When not in use, the roller extension tables (G) ig. 12, one of which is shown, can be lowered in front and back of the planer to prevent accidental movement, which could result in misalignment of the rollers. To lower the tables, raise the end of extension table (G) ig. 13, slightly to relieve pressure on the table support () and move the table support inward away from clip (), while lowering extension table (G). G ig ig. 14, illustrates the stand with roller extension tables assembled to a elta 15 C-380 Planer. ig. 14 5

6 MCHINRY PRTS, SRVIC OR WRRNTY SSISTNC ll elta Machines and accessories are manufactured to high quality standards and are serviced by a network of Porter-Cable/elta actory Service Centers and elta uthorized Service Stations. To obtain additional information regarding your elta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call MCHINRY elta uilding Trades and Home Shop Machinery Two Year Limited Warranty elta will repair or replace, at its expense and at its option, any elta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a elta factory service center or authorized service station with proof of purchase of the product within two years and provides elta with reasonable opportunity to verify the alleged defect by inspection. elta may require that electric motors be returned prepaid to a motor manufacturer s authorized station for inspection and repair or replacement. elta will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other than an authorized elta Service facility or representative. Under no circumstances will elta be liable for incidental or consequential damages resulting from defective products. This warranty is elta s sole warranty and sets forth the customer s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by elta. 6 Printed in U.S..