Assembly Guidelines for Matrix Strength Equipment

Size: px
Start display at page:

Download "Assembly Guidelines for Matrix Strength Equipment"

Transcription

1 Assembly Guidelines for Matrix Strength Equipment For use at Assembly, Installation & Service Key: Axle Arm 180 N-m / 133 ft.lb. M10 Bolt & Nut 77 N-m / 57 ft.lb. M10 Bolt & Frame Rivnuts 40 N-m / 30 ft. lb. M8 Bolts 25 N-m / 18 ft.lb. M8 Plastic and M6 Bolts 15 N-m / 11 ft.lb. Pad Bolts 10 N-m / 7 ft.lb. BRIAN.NELSON V

2 Frame Connection Joints for Ultra (G7), Aura (G3), or Versa 1. Any frame connection bolt should have Vibra-Tite 135 Red Gel (see appendix for details) applied to the threads during assembly or anytime the bolt is re-assembled. Blue patch on bolts is not acceptable for locking 2. A M10 bolt should be torqued to 40 N-m if it is being used with a nylock nut (Versa). Vibra- Tite 135 Red Gel should be added to the bolt threads after passing through the tube and washer. 3. A M10 bolt should be torqued to 40 N-m if it is being used in a rivnut (G7 Ultra). Vibra-Tite 135 Red Gel should be applied to the bolt threads after assembling the washer. BRIAN.NELSON V

3 Ultra (G7) Pivot Joints 1. Any pivot axle shall have Vibra-Tite 135 Red Gel applied and torqued to 180 N-m. Comes from factory this way so no need to do this in assembly. This is just for service when necessary. Assembly must still grease the axle. Grease 2. Add Vibra-Tite 135 Red Gel to the four M10 bolts (see below), center the arms then torque to 77 N-m. 3. The single M10 bolt (see below) connecting the arm to the axle should receive Vibra-Tite 135 Red Gel. Torque to 77 N-m. #2 - Four M10 Bolts #3 - Single M10 Bolt BRIAN.NELSON V

4 Versa Pivot Joint 1. Use Vibra-Tite 135 Red Gel on the M10 and M12 hardware attaching the axle to the frame pivot. Torque the M10 bolt to 77 N-m and torque the M12 bolt to 130 N-m Versa Model Numbers GM59 Chest Press GM63 Shoulder Press GM65 Lat Pull BRIAN.NELSON V

5 Ultra (G7), Aura (G3), and Versa Tie Rods 1. The ball on the tie-rod must be greased with Super Lube grease 2. The axle attaching the tie-rod should be coated with anti-seize a. Tie rods on G7 (Ultra) should be set to the length in the OM and the jam nuts should be tightened with a wrench b. Tie rods on Versa should have the screw fully engaged and the jam nuts tightened with a wrench 3. Place Vibra-Tite 135 red gel on the M6 bolt and torque to 15 N-m for all machine except the Lat Pull Down. The Lat Pull Down shall have Vibra-Tite 135 red gel and torqued to 30 N-m Anti-Seize Grease Ultra (G7) Model Numbers GM40 Shoulder Press GM41 Chest Press GM42 Lat Pull GM43 Seated Row GM45 Leg Curl GM48 Abdominal Versa Model Numbers GM63 Conv. Shoulder Press GM59 Conv. Chest Press GM65 Div. Lat Pull GM61 Seated Leg Curl Aura (G3) Model Numbers GM27 Conv. Shoulder Press GM29 Conv. Chest Press GM26 Div. Lat Pull GM30 Abdominal Crunch BRIAN.NELSON V

6 Back Pad Adjustment Plate 1. Remove caps on seat assembly that have the chrome back pad adjustment plate on it. 2. Remove the 4 M5 bolts (2 under each cap) and apply Vibra-Tite 135 Red Gel and torque hand tight. Ultra (G7) Model Numbers GM44 Leg Ext GM45 Leg Curl BRIAN.NELSON V

7 Arm Curl Handlebar 1. Apply Vibra-Tite 135 Red Gel to the handlebar bolt and torque to 77 N-m. BRIAN.NELSON V

8 Seat Assembly 1. Place Vibra-Tite 135 Red Gel on the M8 bolts for the seat assembly and torque them to 25 N-m (G7) Ultra Versa BRIAN.NELSON V

9 All Other Locations 1. All other locations should use the rule that all M8 and M10 bolts will have Vibra-Tite 135 Red Gel applied except for the following locations a. The aluminum wing on G7 Ultra and Versa b. The cable adjustment bolts on Versa All Strength Pad Bolting 1. All bolts for pads WITH PLASTIC, do not apply Vibra-Tite 135 Red Gel 2. All bolts for pads WITHOUT PLASTIC, do not apply Vibra-Tite 135 Red Gel NOTE: Do NOT use impact drills on pad bolts BRIAN.NELSON V

10 Disassembly and Re-assembly of Strength Units 1. Units should be disassembled only when they cannot fit through spaces (doors, hallways, etc.). 2. The best option for disassembly is to disconnect the frame from the weight stack. 3. First, disconnect the cable which will often be at the cam assembly on the frame. Mark with a pen which slot the cable is placed in. Take a photo showing the cable s route through the frame. 4. Second, unbolt all the frame connection joints. Throw away all nylock nuts that were removed (when applicable). 5. Move the equipment to its intended location. 6. Re-assemble the frame to the weight stack using the original bolts and new nylock nuts (if used). a. G7 units: make sure that the lower connection bar is positioned right-side up. If it is attached upside down, the unit will not be stable. b. Loosely install the hardware, do not pass the bolt all the way through the nut. c. Once the machine is in the correct placement on the floor, give it a small shake to make sure it is settled. Remove hardware pieces one at a time, apply Vibra-Tite 135 Red Gel, reinstall the hardware, and then torque appropriately. The torque for a bolt into a M10 Rivnut is 40 N-m. The torque for a bolt into a M10 Nut is 40 N-m. 7. Since Vibra-Tite 135 Red Gel needs 24 hours to cure, machines should be allowed to sit for 24 hours before regular use. 8. Install the cable back into the cam. Check all pulleys to ensure the cable has not fallen off. Perform the machine s exercise. 9. Adjust the cable tension if necessary. 10. Lubricate the guide rods using Super Lube aerosol. 11. Test the unit and listen for noises. BRIAN.NELSON V

11 G7 Ultra - Cable Tensioning Guide Cable Installation Tension Setting Procedure 1. Loosen the jam nut and remove the weight stack pin 2. Tighten cable bolt until head plate begins to move (lifts up) 3. Tighten jam nut using a wrench 4. Put as much weight on as possible, perform exercise to set cable 5. Repeat 1-3 to take stretch from 4 out of cable 6. Check cable screw with new 2014 tension gauge (part # ) and adjust position of cam clip as necessary 7. Check to make sure weight stack pin goes into every hole without hitting the bayonet Must NOT fit between bottom of the cable bolt head and the top of the jam nut (Maximum) Must fit between bottom of the cable bolt head and the top of the jam nut (Minimum) Part # Used for LARGE Head Plate Adapter Used for SMALL Head Plate Adapter Must NOT fit between bottom of the cable bolt head and the top of the jam nut Fits = NOT good, Doesn t fit = Good BRIAN.NELSON V

12 Head Plate Adapter Sizes Ultra (G7) Model Numbers GM40 Shoulder Press GM41 Chest Press GM42 Lat Pull GM44 Leg Ext GM45 Leg Curl GM46 Arm Curl GM47 Tricep GM48 Abdominal GM49 Leg Press GM52 Pec Fly GM53 Back Ext GM54 Prone Leg GM55 Glute GM56 Rotary Torso GM57 Calf Ext GM58 Lat Raise BRIAN.NELSON V

13 Small Head Plate Adapter Acceptable range for bottom of bolt head Bottom of screw is too far out not enough thread engagement for safe operation. Cam clip should be moved out. Example Move cable keeper in cam Red tab on gauge must NOT fit between bottom of bolt head and top of jam nut Not enough threads in adapter BRIAN.NELSON V

14 Large Head Plate Adapter EXAMPLE 1: Bottom of bolt is too far up, not enough bolt thread engagement for safe operation. Move cam clip out.. EXAMPLE 2: Bottom of bolt is too close to adapter. Move cam clip in. Acceptable range for bottom of bolt head Example 1 Move cam clip in Red tab on gauge must NOT fit between bottom of bolt head and top of jam nut Not enough threads in adapter BRIAN.NELSON V

15 Example 2 Move cam clip in cam Green tab on gauge must fit between bottom of bolt head and top of jam nut Cable Tension Checking Procedure 1. Remove weight stack pin 2. Place cable tension gauge against the front of the 2 forward guide rods. Position gauge halfway between the cable bolt and the top if the weight stack 3. Push cable left and right with your finger a. The head plate should begin to move (lift up) before the cable gets to the outside indicator lines on the gauge b. If the cable goes past the lines without movement, perform Cable Installation Tension Setting Procedure above Red arrow (dashed) is showing the cable is too loose Green arrow is showing the cable tensioned properly Video: BRIAN.NELSON V

16 G3 Aura Belt Tensioning Guide 1. Loosen bolts on fold over clamp or barrel clamp 2. Using your hand pull any slack out of the belt and using a pliers on the cut end of the belt pull to remove that slack 3. Tighten bolts using the instruction below For belting with the fold over type clamp: The bolts (with Vibra-Tite 135 Red Gel (this is important as it acts as a lubricant and is related to the torque spec) should be tightened to 5 N-m using a torque wrench. The bolts should be tightened in a uniform pattern. For belting with the barrel type clamp: The bolts (with Vibra-Tite 135 Red Gel (this is important as it acts as a lubricant and is related to the torque spec) should be tightened to 30 N-m using a torque wrench. The bolts should be tightened in a uniform pattern. BRIAN.NELSON V

17 Versa Cable Tensioning Guide The cable on all Versa machines can be adjusted at the bottom portion of the weight stack. 1. Loosen the two M10 bolts seen in the picture. 2. Using a 6 mm hex wrench, turn the adjuster bolt up or down to tighten the cable. a. A properly tensioned cable will lift the head plate with mm of deflection of the cable. 3. Torque the two M10 bolts to 77 N-m once the proper cable tension has been achieved. BRIAN.NELSON V

18 Tools and Supplies 1. Vibra-Tite 135 Red Gel a. This thread-locker should be applied where specified in this guide b. Gel should be applied to bolt threads around the entire diameter c. Gel should be applied after assembly of washers and through tubes to prevent gel from scraping off d. Gel should be applied and the bolt should be torqued to the appropriate level within 5 minutes of application e. This is only for chrome plated bolts 2. Anti-Seize Lubricant a. Should be applied after cleaning of the application surface b. A thin application should be applied over the entire surface of designated area Tube Brush On Stick BRIAN.NELSON V

19 3. Torque Wrench - able to measure in N-m To help you become familiar with a torque wrench, below are a few steps you can use to learn how to handle this tool. First, you should become familiar with the torque wrench by examining it closely. It should resemble a standard wrench except for a few key differences. The biggest difference is the dial that should be located near the bottom of the handle. When this dial is turned, it increases or decreases the level of strength of the clamp. This will in turn increase or decrease the force exerted on a nut or bolt. The level of torque that a torque wrench is set at is extremely important. Using the wrong torque can damage what you re working on. This can be dangerous, for example, if a nut or bolt is damaged and then becomes loose while equipment is in use. Review this document for appropriate torque for each bolt on a strength unit. Different models use different bolts that will need to be adjusted with different levels of torque. Adjusting the torque is quite easy. The dial near the handle simply has to be spun either forwards or backwards. However, you should observe the level you are setting the torque at quite carefully. BRIAN.NELSON V

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 5/16 x 2 Hex Bolt (B) 5/16 x 2-1/4 Hex Bolt (C) 5/16 x 2-1/2 Hex Bolt (D) 4X 5/16 x 3/4 Hex Bolt (E) 4X 5/16 x 1-1/4 Hex Bolt (F) 11X 5/16 Flat Washer (G) 12X 5/16 Nylock Nut

More information

A SSEMBLY INSTRUCTION MAN UAL

A SSEMBLY INSTRUCTION MAN UAL A SSEMBLY INSTRUCTION MAN UAL TABLE OF CONTENTS: Introduction- Pg. 1 Assembly for TG-150- Fig. 1-71 Cable Mapping Diagram- Pg. 20 Cable Adjustments- Fig. 42, 65, Pg. 19 Exploded View Diagram- Pg. 22 Parts

More information

Hardware and Components:

Hardware and Components: Hardware and Components: (A) 4X 5/16 x 1 Carriage Bolt (B) 2X 5/16 x 2-1/4 Carriage Bolt (C) 2X 5/16 x 3-1/4 Hex Bolt (D) 2X 5/16 x 3/4 Hex Bolt (E) 2X 5/16 x 1-1/4 Hex Bolt (F) 5/16 x 2-1/4 Hex Bolt (G)

More information

ODY-5. Odyssey Home Gym TABLE OF CONTENTS: Introduction - Pg. 1. Safety Precautions - Pg. 2. Assembly for ODY-5 - Pg. 3 - Pg. 18, Pg.

ODY-5. Odyssey Home Gym TABLE OF CONTENTS: Introduction - Pg. 1. Safety Precautions - Pg. 2. Assembly for ODY-5 - Pg. 3 - Pg. 18, Pg. TABLE OF CONTENTS: Introduction - Pg. 1 Safety Precautions - Pg. 2 O W N E R S M A N U A L Assembly for ODY-5 - Pg. 3 - Pg. 18, Pg.20 Cable Adjustments - Pg. 19 Cable Mapping Diagram - Pg. 21 - Pg. 24

More information

STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL

STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will

More information

Lumber Smith. Assembly Manual. If you are having problems assembling the saw and need assistance, please contact us at:

Lumber Smith. Assembly Manual. If you are having problems assembling the saw and need assistance, please contact us at: Lumber Smith Assembly Manual If you are having problems assembling the saw and need assistance, please contact us at: 804-577-7398 info@lumbersmith.com 1 Step 1 Safety Carefully read the Owners Manual.

More information

LEG CURL IP-S1315 INSTALLATION INSTRUCTIONS

LEG CURL IP-S1315 INSTALLATION INSTRUCTIONS LEG CURL IP-S35 INSTALLATION INSTRUCTIONS Copyright 2009. Star Trac by Unisen, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without first obtaining written

More information

AUGMENT THE WEIGHT STACK SELECTION PRO SELECTION PRO MED INSTALLATION MANUAL

AUGMENT THE WEIGHT STACK SELECTION PRO SELECTION PRO MED INSTALLATION MANUAL AUGMENT THE WEIGHT STACK SELECTION PRO SELECTION PRO MED INSTALLATION MANUAL REV 1.0 LANG: ENG DATE: 2016.06.03 1/33 SOMMARIO 1 INFORMATION NOTE... 4 2 TOOLS... 4 3 PERSONAL PROTECTIVE EQUIPMENT... 4 4

More information

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )

The Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 ) P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your

More information

PERSONAL RECORD KEEPING

PERSONAL RECORD KEEPING 2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain

More information

Serial Number Location

Serial Number Location GL/GLX STRENGTH TRAINING SYSTEM OWNERS MANUAL Serial Number Location SERIAL 3 4 5 7 8 Record your Serial number and purchase date here: S/N DATE: DEALER: Model No. BCG-GL BODYCRAFT is a division of Recreation

More information

Cam Handle Service Guide

Cam Handle Service Guide Cam Handle Service Guide Page 2. Introduction Page 3. Troubleshooting guide Page 4-5. Adjusting the clamp force Page 6-7. Disassembling, greasing and replacing components Page 8-9. Replacing the post bearings

More information

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:

USE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT: 1963-1972 C10 Chevy Truck Custom IFS Installation Instructions Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE PARTS LIST BELOW

More information

Technical Procedure. HIITMill (X) Push/Pull Brake Cable Install

Technical Procedure. HIITMill (X) Push/Pull Brake Cable Install HIITMill (X) Push/Pull Brake Cable Install Applies to: HIITMill and HIITMill X Required Tools: 2.5mm Allen Key 3mm Allen Key 4mm Allen Key 5mm Allen Key 6mm Allen Key 10mm Wrench 10mm Socket Ratchet Needle

More information

Intercooler Shroud and Belt Cover for WRX

Intercooler Shroud and Belt Cover for WRX Intercooler Shroud and Belt Cover for 2015+ WRX 2016-05-18 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation

More information

INSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)

INSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only) INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied

More information

HOME GYM Owner s Manual

HOME GYM Owner s Manual HOME GYM Owner s Manual Content Content-------------------------------------------------------------1 Safety precautions----------------------------------------------------2 Assembly instruction-------------------------------------------------3-12

More information

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems with A/C #13600 / #13620

Small Block Ford. 289 / 302 / 351W / 5.0 Installation Manual For Systems with A/C #13600 / #13620 Small Block Ford 289 / 302 / 351W / 5.0 Installation Manual For Systems with A/C #13600 / #13620 Billet Specialties, Inc. 500 Shawmut Avenue. La Grange, Illinois 60526 Tech Line (708) 588-0505 Fax (708)

More information

RPS. XR Front Drive Updates CORPORATION

RPS. XR Front Drive Updates CORPORATION FACTORY CAT 1. To start a replacement of the XR Front Wheel Drive, make sure the machine is on level ground with the rear wheels chocked and always disconnect the batteries. 2. Locate the Positive and

More information

Strata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at

Strata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at 1A Watch our assembly videos at www.strataf.com/videos Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached Back Panel

More information

INSTALLATION INSTRUCTIONS CHEVY C-10 INDEPENDENT FRONT SUSPENSION

INSTALLATION INSTRUCTIONS CHEVY C-10 INDEPENDENT FRONT SUSPENSION INSTALLATION INSTRUCTIONS 73-87 CHEVY C-10 INDEPENDENT FRONT SUSPENSION Please read these instructions completely before starting your installation. Assemble suspension on vehicle before powder-coating

More information

PERSONAL RECORD KEEPING

PERSONAL RECORD KEEPING Q47e/Q47ce 2 Q 4 7 e / Q 4 7 c e A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING IMPORTANT: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make

More information

Tip In Dock Instructions 2016 Design

Tip In Dock Instructions 2016 Design Table of Contents Tip In Dock Instructions 2016 Design 1. Dock Assembly and Set-Up 1.1 Quick Start 1.2 Installing Dock Legs 1.3 Positioning Hinges 1.4 Installing Foot Pads 1.5 Installing Cross Braces 1.6

More information

Removing the Z-Axis lead screw

Removing the Z-Axis lead screw Page 1 of 8 TITLE: Sabre Z-Axis Lead Screw Replacement Procedure Gerber FastFact #: 5048 Supplied by: Gerber Hardware Support Last Modified: June 14, 2007 Summary: Tools used: The following procedure explains

More information

PFT CABLE GYM INSTRUCTION MANUAL

PFT CABLE GYM INSTRUCTION MANUAL PFT CABLE GYM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your

More information

To install new top weight plate bushings in G7 strength units.

To install new top weight plate bushings in G7 strength units. 1/5 PURPOSE To install new top weight plate bushings in G7 strength units. RE-WORK PARTS REQUIRED - ZMS4000424 Top Weight Plate Bushing (Quantity 4 per machine). - Matrix Top Weight Plate Bushing Removal

More information

Installation Instructions Precision Sport Shifter

Installation Instructions Precision Sport Shifter Installation Instructions Precision Sport Shifter 2004 and up Pontiac GTO Part Number 45043 2010, 2005, 2004 by B&M Racing and Performance Products This B&M Precision Sport Shifter has been designed to

More information

Nancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual

Nancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual Nancy s Knit Knacks LLC 4 Yard Option Upgrade Kit Assembly Instructions and User Manual Thank you for purchasing our 4 Yard Option (4YO) Upgrade Kit. To install this upgrade you are simply going to assemble

More information

RTI TECHNOLOGIES, INC.

RTI TECHNOLOGIES, INC. RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally

More information

INSTALLATION INSTRUCTIONS Product No. MULTI-FIT PICK-UP

INSTALLATION INSTRUCTIONS Product No. MULTI-FIT PICK-UP INSTALLATION INSTRUCTIONS Product No. You can take it with you. PLYMOUTH, MICH. MULTI-FIT PICK-UP 37034 SMALL PARTS PACKAGE 37424 WARNING: DO NOT LUBRICATE THREADS, BOLT FAILURE MAY OCCUR DUE TO OVER TIGHTENING.

More information

Xceed ASSEMBLY MANUAL

Xceed ASSEMBLY MANUAL Xceed ASSEMBLY MANUAL Table of Contents / Registration Congratulations on your commitment to fitness and your purchase of the Bowflex Xceed home gym. Before assembling your Bowflex Xceed home gym please

More information

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS

400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS 12/11/07 PAGE 1 OF 12 400A 40113V, 401A 40120V, & 401AL 40120VL ALUMINUM VERTICAL 4000 LB LIFT INCLUDES SCREW LEG ASSEMBLY INSTRUCTIONS Thank you for purchasing our product! *Please read these instructions

More information

Aluminum Lake Truss Dock Instructions

Aluminum Lake Truss Dock Instructions Table of Contents Aluminum Lake Truss Dock Instructions 1. Dock Assembly and Set-Up 1.1 Quick Start 1.2 Positioning Quick Clips 1.3 Installing Dock Legs 1.4 Installing Foot Pads 1.5 Installing Cross Braces

More information

ABM International, Inc.

ABM International, Inc. ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket

More information

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS Thank you for your purchase of the C4 Fabrication s 5th Gen 4Runner Rock Sliders! This product was carefully crafted to ensure a perfect

More information

08+ KAWASAKI KLR PD NERF

08+ KAWASAKI KLR PD NERF 08+ KAWASAKI KLR PD NERF 0505-1299 Before you begin, place the bike on a hard level surface where you have room to work. Lay out the parts included in this kit and compare to the parts list on page 5 of

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL FASTENER AND HARDWARE GENERAL REQUIREMENTS 1. DESCRIPTION This section contains general requirements for common hardware installation. Covered are selection and installation of cotter pins, installation

More information

PERSONAL RECORD KEEPING

PERSONAL RECORD KEEPING PRO3700 2 P R O 3 7 0 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for

More information

INSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM

INSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM INSTRUCTION MANUAL LEG PRESS OPTION OF ELITE GYM QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will

More information

CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL

CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL CFT STRENGTH TRAINING SYSTEM OWNER'S MANUAL Serial Number Location SERIAL 8 Record your Serial number and purchase date here: S/N PURCH.DATE: DEALER: Scan this QR code with your PortableDevice to link

More information

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer

REPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET

More information

DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0

DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0 DYNATRAC PRODUCTS 2007-2016 4X4 JEEP JK HEAVY DUTY BALL JOINT JP44-2X3050-C DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0 WARNING: Improper use or installation of this product can cause major failures

More information

TIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter

TIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together

More information

Floating Lake Truss Dock Instructions

Floating Lake Truss Dock Instructions Table of Contents Floating Lake Truss Dock Instructions 1. Dock Assembly and Set-Up 1.1 Installing Dock Floats 1.2 Positioning Quick Clips 1.3 Installing Anchor Posts 1.4 Installing Docks into the Water

More information

Installation Instructions

Installation Instructions The IMS ETERNAL FIX PATENT PENDING Installation Instructions EPS recommends professional installation for the Eternal IMS Fix. Please take all precautionary safety measures. We also recommend putting the

More information

Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens

Installation and Assembly: In-wall Mount for 32 to 71 Flat Panel Screens Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S

More information

Big Block Chevrolet Installation Manual For Systems with A/C #14220 / #14120

Big Block Chevrolet Installation Manual For Systems with A/C #14220 / #14120 Big Block Chevrolet Installation Manual For Systems with A/C #14220 / #14120 Billet Specialties, Inc. 500 Shawmut Ave. La Grange, IL 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 PLEASE READ ALL INSTRUCTIONS

More information

PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0

PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 DYNATRAC PRODUCTS 2003-2010 4X4 DODGE 2500/3500 HEAVY DUTY BALL JOINT PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 WARNING: Improper use or installation of this product can cause major failures that could

More information

Contractors Rack Assembly and Installation Instructions

Contractors Rack Assembly and Installation Instructions Part # 18601 & 16601 Contractors Rack Assembly and Installation Instructions 4751 Littlejohn St. Unit A, Baldwin Park, CA 91706 Page 1 of 12 11/13/08 Thank you for purchasing the Paramount Restyling Contractors

More information

A s s e m b l y I n s t r u c t i o n s

A s s e m b l y I n s t r u c t i o n s by Body-Solid A s s e m b l y I n s t r u c t i o n s Be careful to assemble all components in the sequence they are presented. NOTE: Finger tighten all hardware in this step. Do Not wrench tighten until

More information

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide The following guidelines should be followed to lubricate the three main parts of the 400QMD mount. The QMD stands for Quartz Micro-Drive controller.

More information

STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL

STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL STRATA STRENGTH TRAINING SYSTEM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will

More information

PHG-1000X. Owner s Manual HOME GYM

PHG-1000X. Owner s Manual  HOME GYM HOME GYM Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES:! " # $ % & ' ( ) * + ' (, ' " -. *, * ) )

More information

Cottage Style Dock Instructions

Cottage Style Dock Instructions Cottage Style Dock Instructions Table of Contents 1. Dock Assembly and Set-Up 1.1 Quick Start 1.2 Positioning Quick Clips 1.3 Installing Dock Legs 1.4 Installing Foot Pads 1.5 Installing Cross Braces 1.6

More information

WPS crew Doors Installation instructions

WPS crew Doors Installation instructions WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left

More information

model tsa-sa48 Sliding Crosscut Table installation guide

model tsa-sa48 Sliding Crosscut Table installation guide model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop

More information

BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms

BABY WOLF LOOM. Assembly Instructions for Knocked-Down Looms BABY WOLF LOOM Assembly Instructions for Knocked-Down Looms BEFORE YOU BEGIN Please read through the directions before beginning to assemble your loom. Unpack the loom parts carefully. Do not throw away

More information

INSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON RED WING LATHE

INSTALLATION OF WELLS SUPER QUICK CHUCK LEFT HAND ON RED WING LATHE DENTAL, INC. TECHNICAL BULLETIN Q824-022510 5860 FLYNN CREEK ROAD READ ALL INSTRUCTIONS P.O. BOX 106 BEFORE PROCEEDING COMPTCHE, CALIFORNIA, U.S.A. 95427 SAVE THIS FOR FUTURE REFERENCE www.wellsdental.com

More information

Handout Activity: HA043

Handout Activity: HA043 Handout Activity: HA043 Student/Intern information: Name Date Class Summary There are many different fasteners used in automotive applications, including screws, bolts, studs & nuts. Washers & chemical

More information

TorqueMaster Replacement Spring

TorqueMaster Replacement Spring TorqueMaster Replacement Spring Installation Instructions NOTE: Use these installation instructions in conjunction with the TorqueMaster Repair / Replacement Spring Program literature. Copyright 999 Wayne-Dalton

More information

Masterpiece Module Kits N T-trak Module Kit Assembly Instructions

Masterpiece Module Kits N T-trak Module Kit Assembly Instructions Masterpiece Module Kits N T-trak Module Kit Assembly Instructions For tips, watch Instructional Video at http://www.youtube.com/watch?v=fklebffclau Tools Required flat, sturdy work surface Quality grade

More information

LifeGear G1 /HOME GYM ITEM NO.: 63100

LifeGear G1 /HOME GYM ITEM NO.: 63100 LifeGear G1 /HOME GYM ITEM NO.: 63100 OWNER S MANUAL IMPORTANT: Read all instructions carefully before using this product. Retain this owner s manual for future reference. The specifications of this product

More information

RC4WD Diablo V2 Instruction Manual

RC4WD Diablo V2 Instruction Manual Version 1.1 RC4WD Diablo V2 Instruction Manual Thank you for your purchase. Welcome to the RC4WD family. This kit is a combination of many specially engineered and manufactured parts. Enjoy your build.

More information

Form No Assembly & Operating Instructions for: SAFETY PRECAUTIONS

Form No Assembly & Operating Instructions for: SAFETY PRECAUTIONS Form No. 0230 Assembly & Operating Instructions for: 833 20300 83 2220 837 0-0008 078 SHOP PRESS Max. Capacity: 2 Ton These instructions are intended for various shop presses. Some models are shipped assembled

More information

Customer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR

Customer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from

More information

Calf-Tel Pen System Assembly Instructions

Calf-Tel Pen System Assembly Instructions Calf-Tel Pen System Assembly Instructions (Instructions work for 4, 6, and the 7 Pen Systems) 1 ASSEMBLY OF PEN FRONT AND WALLS START THE ASSEMBLY BY LINING UP THE TWO UNI-DIRECTIONAL ARROWS IN THE TOP,

More information

Written By: Brook Drumm

Written By: Brook Drumm Simple 1401 Assembly For kits produced between 1/15/14-6/1/14. This guide is for kits with the Fan Shroud. Instructions for metal and wood extruder (and bed) included below. Written By: Brook Drumm TOOLS:

More information

Hatchback Wing Riser Kit

Hatchback Wing Riser Kit Hatchback Wing Riser Kit 2015-06-11 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket

More information

CHEVY SuperBracket Mounting Kit #0826

CHEVY SuperBracket Mounting Kit #0826 CHEVY SuperBracket Mounting Kit #0826 #1200 SuperGlide (16K) #0800 SuperGlide (20.5K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)

More information

Repair Instructions. Replacing a La Z Time Mechanism Side Subassembly. Remove the Back(s): Remove the Mechanism Assembly: CAUTION.

Repair Instructions. Replacing a La Z Time Mechanism Side Subassembly. Remove the Back(s): Remove the Mechanism Assembly: CAUTION. Replacing a La Z Time Mechanism Side Subassembly Tools Required: Slotted Screwdriver Power Driver 8" Driver Extension Ruler Note: Extension springs are not typically used on non-chaise standard width styles,

More information

The Bowflex Blaze Home Gym Assembly Manual

The Bowflex Blaze Home Gym Assembly Manual The Bowflex Blaze Home Gym Manual P 001-6903 Rev A (4/2006) Safety Precautions 1 Get to Know Your Machine 2 Basic Principles 3 Parts List 3 Hardware List 3 Accessory List 3 Hardware Guide 4 Tools You Will

More information

CONTROLS KIT FOR ALL # & # HARLEY DAVIDSON SPORTSTER MODELS

CONTROLS KIT FOR ALL # & # HARLEY DAVIDSON SPORTSTER MODELS INSTALLATION INSTRUCTIONS TC BROS. CHOPPERS PART #0-0075 & #0-0076 (No Pegs) FORWARD CONTROLS KIT FOR ALL 00-0 HARLEY DAVIDSON SPORTSTER MODELS If downloading & printing these instructions online, be sure

More information

INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: ,

INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: , INSTALLATION INSTRUCTIONS CONTOURED LIGHT BAR APPLICATION: 2010-2014 CHEVY EQUINOX/ GMC TERRAIN PART NUMBERS: 32-21020, 32-21025 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 CONTOUR BAR TORQUE WRENCH 2 1

More information

What is a fastener? A device to locate or hold parts

What is a fastener? A device to locate or hold parts What is a fastener? A device to locate or hold parts As a repair technician you will become skilled at removing, reconditioning, replacing, and installing fasteners. An important skill to learn is how

More information

BOLT ON LONG TRAVEL FOR E-Z-GO

BOLT ON LONG TRAVEL FOR E-Z-GO INSTALLATION INSTRUCTIONS BOLT ON LONG TRAVEL FOR E-Z-GO 1994 2000 Model E-7-04 E-7-06 TABLE OF CONTENTS Progressive Supension Kit... 2 Kit Contents...3-4 Disassembly...5-10 Frame Assembly...11-14 Frame

More information

CHEVY/GMC SuperRail Mounting Kit #4423

CHEVY/GMC SuperRail Mounting Kit #4423 CHEVY/GMC SuperRail Mounting Kit #4423 #4100 SuperGlide (16K) #4400 SuperGlide (20K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 16,000 lbs. 4,000 lbs. Gross Trailer Weight (Maximum)

More information

Assembly Instructions 10 X 10 Aluminum Roof Support

Assembly Instructions 10 X 10 Aluminum Roof Support Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1

More information

Service Bulletin: Cable Field Upgrade. Date Prepared: 11/21/2018

Service Bulletin: Cable Field Upgrade. Date Prepared: 11/21/2018 Service Bulletin: Cable Field Upgrade Prepared by: Emilie McWilliams, Don Stiemke, Bill Baier, Brian Nelson Date Prepared: 11/21/2018 Models Affected: G3-MSFT3; G3-MSFT4; G3- MS20, 40, 50, or 80; VS-VFT;

More information

CHEVY/GMC SuperRail Mounting Kit #3117

CHEVY/GMC SuperRail Mounting Kit #3117 CHEVY/GMC SuperRail Mounting Kit #3117 #3100 SuperGlide (12K) Gross Trailer Weight (Maximum) Vertical Load Weight (Max. Pin Weight) 12,000 lbs. 3,000 lbs. Installation Instructions SPECIFICATIONS Fits

More information

Maintenance & Parts list for:

Maintenance & Parts list for: Maintenance & Parts list for: Industrial gun GB 2 Juni 2017 This Maintenance & Parts list for industrial gun is prepared by : Winchester Europe Service V. Parbst & Søn as a comprehensive maintenance guide

More information

Electric Skein Winder

Electric Skein Winder Electric Skein Winder Assembly and Use Package Contents 1 - Triangular Body (w/ motor) 1 - Cross Arm 1 - Left Foot (w/ yarn guide) 1 - Right Foot 1 - Adjustable Finger (w/ yarn clip) 3 - Adjustable Fingers

More information

FLOE DOCK FURNITURE WARNING ASSEMBLY INSTRUCTIONS

FLOE DOCK FURNITURE WARNING ASSEMBLY INSTRUCTIONS FLOE DOCK FURNITURE ASSEMBLY INSTRUCTIONS KIT P/N 510-00400-02 KIT P/N 510-00405-02 KIT P/N 510-00406-02 KIT P/N 510-00410-02 WARNING IT IS THE INSTALLER S RESPONSIBILITY TO PROPERLY INSTALL this chair

More information

Pickup Box Utility Rack Package Installation (Instruction ID: )

Pickup Box Utility Rack Package Installation (Instruction ID: ) 017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation

More information

00108/00110 INSTRUCTION MANUAL

00108/00110 INSTRUCTION MANUAL 00108/00110 INSTRUCTION MANUAL Removable and Adjustable Mudflap System IMPORTANT! Exhaust Systems Note: Any modifications to the factory installed exhaust system may void your manufacturer s warranty.

More information

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards. Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all

More information

SMALL BLOCK CHEVROLET

SMALL BLOCK CHEVROLET SMLL LOCK CHEVROLET Installation Manual For Systems with /C #13220 / #13120 illet Specialties, Inc. 500 Shawmut ve. La Grange, IL 60526 Tech (708) 588-0505 Fax (708) 588-7181 PLESE RED LL INSTRUCTIONS

More information

Machine Quilting Frame assembly, and instruction manual

Machine Quilting Frame assembly, and instruction manual Machine Quilting Frame assembly, and instruction manual Table of Contents Parts List................. Pg. 2 Step 1 - Legs............... Pg. 4 Step 2 - Lower Leg Brace....... Pg. 5 Step 3 - Frame Ends..........

More information

Required Tools: Procedure:

Required Tools: Procedure: Depending on the materials you process through your chipper, their moisture content, the climate you live in, and many other factors you may have difficulty removing the rotor from the engine shaft. The

More information

LS1/LS6 CHEVROLET Installation Manual For Systems without A/C #13405 / #13425

LS1/LS6 CHEVROLET Installation Manual For Systems without A/C #13405 / #13425 LS1/LS6 CHEVROLET Installation Manual For Systems without A/C #13405 / #13425 Billet Specialties, Inc. 500 Shawmut Avenue. La Grange, Illinois 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 PLEASE READ

More information

MODEL 200/220 ASSEMBLY INSTRUCTIONS

MODEL 200/220 ASSEMBLY INSTRUCTIONS V-Twin MFG. Coats Tire Changer VT Part No. 16-0510 This tool should only be used by a knowledgeable and trained motorcycle technician V-Twin Mfg. accepts no responsibility for improper use. MODEL 200/220

More information

Aluminum Lake Truss Dock Instructions

Aluminum Lake Truss Dock Instructions Page 1 of 14 Table of Contents Aluminum Lake Truss Dock Instructions 1. Dock Assembly and Set-Up 1.1 Quick Start 1.2 Positioning Quick Clips 1.3 Installing Dock Legs 1.4 Installing Foot Pads 1.5 Installing

More information

Removing and Replacing the Y-truck

Removing and Replacing the Y-truck Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic

More information

F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1

F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1 F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1 1 P a r t s L i s t : S t a n d a r d L a n d i n g G e a r U p g r a d e Product Code Parts + Spares Product Code Parts + Spares

More information

Introduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions

Introduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop

More information

ASSEMBLY & OPERATION MANUAL

ASSEMBLY & OPERATION MANUAL ASSEMBLY & OPERATION MANUAL RECORD SERIAL NUMBER HERE www.inspirefitness.net by Health In Motion LLC Nov. 2005 CONGRATULATIONS You ve just taken the first step to a healthier and stronger body. This home

More information

COMPETITOR CB-610 STANDARD BENCH

COMPETITOR CB-610 STANDARD BENCH NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice COMPETITOR CB-610 STANDARD BENCH Hardware Identifier Assembly Instruction Exploded Diagram Parts List

More information

Printrbot Simple (Model 1403) Rev F Printrboard

Printrbot Simple (Model 1403) Rev F Printrboard Printrbot Simple (Model 1403) Rev F Printrboard Printrbot Simple is currently shipping with the Rev F Printrboard. Check which rev Printrboard your Simple kit includes and use the corresponding instructions.

More information

Hullavator Gas Spring Replacement (simplified)

Hullavator Gas Spring Replacement (simplified) Hullavator Gas Spring Replacement (simplified) Some Thule Hullavators came with (original owner) lifetime warranties if you are the original owner of a defective Hullavator and can provide proof of purchase

More information

MS25 OPERATION MANUAL

MS25 OPERATION MANUAL SAFETY INSTRUCTIONS SPECIFICATIONS OPERATING INSTRUCTIONS MAINTENANCE ADJUSTMENTS REPLACEMENT OF PARTS MS25 DIAGRAM MS25 PARTS LIST MS25 OPERATION MANUAL SAFETY INSTRUCTIONS Please read these instructions

More information