Footprint Worksurface Assembly Instructions

Size: px
Start display at page:

Download "Footprint Worksurface Assembly Instructions"

Transcription

1 Footprint Worksurface Assembly Instructions Revision E-13 Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service Kimball International, Inc. T F

2 Assembly Instructions Footprint 1 Transaction Counter on Cetra Panels Drill with torque option Tape measure #R 2 square screwdriver bit Level Note: Transaction counters need to be installed prior to any worksurface installation directly beneath them, especially when used with lower panel heights. This is required so that there is room to use a power drill between the bottom of the transaction counter and the lower worksurface. 1. Locate position where transaction counter will be installed on the panel. Insert top hook on top of transaction bracket into the J member slot at a 45 degree angle () 2. Push the top of the transaction counter bracket downward. (). Insert one left and one right handed transaction counter bracket in selected J member for each transaction counter. Wider transaction counters will include an additional right hand bracket to be placed in a J member near the center for support (). Figure D 3. Lay the transaction counter on top of the transaction counter brackets and align with panels as needed (Figure D). 4. Attach the transaction counter to the brackets with screws provided. Three screws are required per bracket. If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision -

3 Assembly Instructions Footprint Support 1 Cetra Panel Mounted Worksurface Tape Measure Drill with torque option #2 Philips head bit #2 R-2 square screwdriver bit Note: Panel mounted worksurface brackets are provided in two types, left or right. (Figures A & B). The top of the brackets should be located 22 3/4 " from the top of the wireway cover for standard height and 19 3/4" for typing height. (). 1. Insert hook on the top of bracket into the panel frame slot at a 45 angle. (Figure D). 2. Push the top of the bracket downward allowing locking tab to engage in the panel slot. (Figure E). 3. Install a bracket at each panel joint in the worksurface layout. Note: When installing the worksurface brackets along the center, you must alternate left brackets and right brackets to prevent a shortage of brackets. (Figure F). If you run short of either left or right brackets, refer to alternate installation diagram. (Figure G). Note: A structural cantilever must be used in place of the standard worksurface brackets when the open kneespace is greater than 48" for 1 3/16" surfaces and 60" for 1 9/16" sur- Figure D Figure F Figure E Left Right Figure G If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision E

4 Assembly Instructions Footprint Support 2 Interworks EQ Panel Mounted Worksurface (continued) 4. Place worksurface on clean, solid surface, back side facing up. Install the flat brackets on the "main" worksurface, approximately 2" from front edge and approximately 6" from back edge of the adjoining worksurface using the screws provided. (Figure H). Ensure that the flat bracket attachment does not interfere with other brackets or components. Two flat brackets are required to join surfaces end to end or at a right angle. 5. Square all panels to aid in alignment and consistent reveals between worksurfaces and panels. (Figure I). 6. Lay the worksurface on the brackets. (Figure J). Tip: Use an undersurface component as additional support until the worksurface bracket is secured to the surface. 7. Lay adjoining worksurface onto brackets. Note: When attaching two surfaces at a right angle, there will be a 1/8" gap between the wire manager and panel. (Figure K). If there is no wire manager, the surfaces should align. (Figure L). 8. Attach adjoining worksurface to the flat brackets with screws provided. (Figure M). Eight screws required per bracket. 9. Adjust worksurface location to ensure alignment of surface joints with panel reveals, if applicable, and control gaps between panel and edges of worksurfaces. DO NOT press wire manager into panel. 10. Attach the worksurfaces to the worksurface brackets using the screws provided. (Figure N). A minimum of two screws Figure J Figure K Figure M Figure N Figure L Figure H Figure I If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision E

5 Footprint Traxx Mounted Worksurface Systems Assembly Instructions Figure D Page 1 of 2 Screw Gun with #2 Phillips Head Bit Torque Option Tape Measure Hook Note: Worksurfaces can be Traxx mounted with worksurface brackets () and supported with pedestals, end panels, and support bases. (). 1. Insert hook on the top of the bracket into the Traxx at a 45 angle. (). 2. Push the top of the bracket downward allowing bracket to hang off of the Traxx. (Figure D). Note: The maximum distance between brackets should be no greater than 48". (Figure E). The maximum span of an unsupported worksurface should not exceed 48" for " worksurfaces and 60" for " worksurfaces. Support is required within 6" of surfaces butted end-to-end. This may be a pedestal or 12" deep support panel. 3. Place worksurface on clean, solid surface, back side facing up. Install the flat brackets on the main worksurface, approximately 2" from front edge and approximately 6" from back edge of the adjoining worksurface using the screws provided. (Figure F). Ensure that the flat bracket attachment does not interfere with other brackets or components. Two flat brackets are required to join surfaces end-to-end or at a right angle. Figure E Figure F 48" or less Main Return 2" 6" If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-06

6 Footprint Systems Assembly Instructions Page 2 of 2 (continued) 4. Lay the worksurface on the brackets. (Figure G). Tip: Use an undersurface component as additional support until the worksurface bracket is secured to the surface. 5. Lay return worksurface onto brackets. Note: When attaching two surfaces at a right angle, there will be a 1 8" gap between the wire manager and Traxx. (Figure H). If there is no wire manager, the surfaces should align. (Figure I). 6. Attach return worksurface to the flat brackets with screws provided. (Figure J). Eight screws are required per bracket. 7. Beginning at one end of the worksurface layout, apply pressure to the front of the ganged worksurfaces while controlling the gaps between the Traxx and back of worksurface. 8. Attach the worksurfaces to the worksurface brackets using the screws provided. (Figure K). A minimum of three screws are required per bracket. Figure H 1 8" Figure J Figure I Figure G Figure K Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-06

7 Assembly Instructions Footprint Support 1 Interworks EQ Panel Mounted Worksurface Tape Measure Drill with torque option #2 Philips head bit #2 R-2 square screwdriver bit Note: Panel mounted worksurface brackets are provided in two types, left or right. (Figures A & B). The top of the brackets should be located 22 3/4 " from the top of the wireway cover for standard height and 19 3/4" for typing height. (). 1. Insert hook on the top of bracket into the panel frame slot at a 45 angle. (Figure D). 2. Push the top of the bracket downward allowing locking tab to engage in the panel slot. (Figure E). 3. Install a bracket at each panel joint in the worksurface layout. Note: When installing the worksurface brackets along the center, you must alternate left brackets and right brackets to prevent a shortage of brackets. (Figure F). If you run short of either left or right brackets, refer to alternate installation diagram. (Figure G). Note: A structural cantilever must be used in place of the standard worksurface brackets when the open kneespace is greater than 48" for 1 3/16" surfaces and 60" for 1 9/16" sur- Figure D Figure F Figure E Left Right Figure G If you have any questions concerning these instructions, please call Kimball Office Customer Care , Revision D

8 Assembly Instructions Footprint Support 2 Interworks EQ Panel Mounted Worksurface (continued) 4. Place worksurface on clean, solid surface, back side facing up. Install the flat brackets on the "main" worksurface, approximately 2" from front edge and approximately 6" from back edge of the adjoining worksurface using the screws provided. (Figure H). Ensure that the flat bracket attachment does not interfere with other brackets or components. Two flat brackets are required to join surfaces end to end or at a right angle. 5. Square all panels to aid in alignment and consistent reveals between worksurfaces and panels. (Figure I). 6. Lay the worksurface on the brackets. (Figure J). Tip: Use an undersurface component as additional support until the worksurface bracket is secured to the surface. 7. Lay adjoining worksurface onto brackets. Note: When attaching two surfaces at a right angle, there will be a 1/8" gap between the wire manager and panel. (Figure K). If there is no wire manager, the surfaces should align. (Figure L). 8. Attach adjoining worksurface to the flat brackets with screws provided. (Figure M). Eight screws required per bracket. 9. Adjust worksurface location to ensure alignment of surface joints with panel reveals, if applicable, and control gaps between panel and edges of worksurfaces. DO NOT press wire manager into panel. 10. Attach the worksurfaces to the worksurface brackets using the screws provided. (Figure N). A minimum of two screws Figure J Figure K Figure M Figure N Figure L Figure H Figure I If you have any questions concerning these instructions, please call Kimball Office Customer Care , Revision D

9 Footprint Systems Assembly Instructions Page 1 of 1 Transaction Counter on Interworks EQ Variable Speed Drill #2 Phillips Tip Bit Package Contents #10 x 1" Phillips Panhead Screws Counter Bracket, left General Information Transaction counter width must equal panel width. Two sets of left and right handed support brackets are included with each counter top. One person can perform all operations. Panels and finish channels must be properly installed, squared and leveled prior to counter top installation. Route all communications prior to installing counter. Counter Bracket, right 1. Locate position where counter top will be installed into panel. Insert each set of left and right handed support brackets into top slot of panel side rail. (). Note: Panel top cap is not removed. All panel finish trim should already be installed. 2. Lay counter top onto brackets and center top approximately 6 1 2" overhang on either side of top. 3. Secure with #10 x 1" screws provided, two screws per bracket. Transaction Counter 6 1 2" Overhang each side 6 1 2" Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision D-07

10 Xsite Systems Assembly Instructions Page 1 of 1 Transaction Counter Bracket Cordless Drill/Driver Tape Measure 3 16" Allen Bit #2 Phillips Screwdriver Bit 3 /8" Drill Bit Caution: Install two brackets for 24" to 60" counters and four brackets equally spaced for 66" to 96" counters. Transaction Surface 1 1 /2" Bolt Bracket 1. Remove tile from one side of structure. Carefully lift up and tilt out. Glass Tiles: Remove both sides. Carefully lift frame without glass up and tilt out. Remove anti-dislodgement wood block. Tilt frame with glass up and out. 2. Place bracket into top channel on top of frame. The frame has pre-punched holes, so no drilling is needed. 3. Position bracket over hole and insert bolt through and into receiver below, fully tighten. 4. Modify panel top cap to fit up to the transaction counter bracket and between brackets. Place top cap sections on panel. 5. Align transaction counter and attach using four #8 x 5 /8" screws provided. (). Repeat for all brackets. 6. Reinstall tiles. Top Channel Receiver Xsite Traxx Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision A-06

11 Assembly Instructions Xsite 1 Metal Leg Pencil Screw Gun #2 Phillips Head Bit Hardware Required U bracket Spacer Block #8x1 Panhead Screw #8x1 Panhead self tapping Screw (Sliver & Black) Spacer Double sided tape backer 1. Align leg with Traxx and place a pencil mark on the post at the bottom edge of the leg assembly. (). 2. Remove film backer from double sided adhesive tape on filler block, attaching it to the frame vertical centered on line drawing in Step 1. On fabric insert tiles, slide U bracket over tile making sure bottom edge is not below pencil line. (). 3. Tilt leg at 45 degree angle and engage top edge of bracket into Xsite Traxx. Lower into vertical location. (). 4. On 24 & 30 deep legs, ensure leg is flush with outside edge of frame vertical. Attach leg with two #8x1 self tapping screws using holes below bottom cross rail. Both black and silver screws have been included so that you may use the one that fits the finish of the metal leg best. (Figure D). Mid support, 10, leg is not required to be attached to frame vertical. 5. Attach surface using #8x1 panhead screws thru under side of leg. (Figure E). Note: On dual sided stations be sure to install end cap before installing legs. Figure E Pencil Mark U bracket Figure D Pencil Mark If you have any questions concerning these instructions, please call Kimball Office Customer Care. Part # , Revision -

12 Xsite Systems Assembly Instructions Page 1 of 1 Worksurface Edge Support Bracket Cordless Drill/Driver #2 Phillips Screwdriver Bit Tape Measure Caution: Worksurface support is required every 48". One bracket is placed at outside edges of a wrapped worksurface. One is placed at the back edge, at the corner, and every 48" for the length of the worksurface. Attachment Plate 1. Tilt attachment plate at 45 angle and engage top edge of bracket into Xsite Traxx at desired location. (). Lower into vertical position. 2. Determine worksurface height. Support plate will adjust in 5 8" increments in attachment plate for worksurface heights from " to 29". 3. Tilt support plate at 45 angle and hook into desired slot in attachment plate. (). Lower into horizontal position. 4. Attach brackets to underside of worksurface with four #8 x 1" screws provided. (). Worksurface #8 x 1" Screws Support Plate Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-07

13 Systems Assembly Instructions Xsite Page 1 of 1 Worksurface Mid-Support Bracket Cordless Drill/Driver Tape Measure 3 16" Allen Bit #2 Phillips Screwdriver Bit Package Contents Mid-Support Bracket 1 1 2"-20 Bolts and Receivers Attachment Plate 8 #8 x 1" Screws Attachment Plate Caution: Mid-supports are required where two worksurfaces are installed end-to-end or when kneespace exceeds 48". Note: Mid-supports are shipped from the factory pre-set for standard worksurface height (29") installation. Mid-supports can adjust vertically down to " in 5 8" increments. (Standing from " to "). 1. If the worksurface is to be installed at lower height, mid-supports will need to be adjusted. Remove two bolts and receivers. Adjust to desired height, reinstall two bolts and receivers and tighten. 2. Tilt attachment plate at 45 angle and engage top edge of bracket into Xsite Traxx at desired location. Lower into vertical position. (). 3. Tilt mid-support at 45 angle and hook into desired slot on attachment plate. Lower into vertical position. (). Note: If height adjustment is required, remove two bolts from lower leg of mid-support and realign with appropriate height holes. Reinsert bolts into receivers and tighten. (). 4. Place worksurface(s) on support plate. If two worksurfaces meet end-to-end on support plate, adjust worksurfaces so all sides are flush with no gaps. Attach support plate to underside of worksurface(s) with the eight #8 x 1" screws provided. (). 5. Adjust glide on mid-support bracket to level worksurface(s). (). Attachment Plate Center Tab Glide Xsite Traxx Receivers Bolts Support Plate #8 x 1" Screws Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision A-06

14 Assembly Instructions Footprint Page 1 of 2 Worksurface Cantilever Bracket on Cetra Panels Drill with Torque Option #R-2 Square Screwdriver Bit Tape Measure Level General Information Standard Height Cantilevers are required when placing two surfaces end to end, when open kneespaces are greater than 48" for 1 3/16" surfaces or 60" for 1 9/16" surfaces, or in configurations where standard panel worksurface bracket support is not possible. Cantilevers are designed so that a single bracket can share the load between two adjacent surfaces. They can be used as sole support for a worksurface. The top of the cantilever should be located 22 3/4" from the bottom of fabric for standard height (29" nominal). (). 22³ ₄" 1. Insert hook on the top of cantilever into the J member at a 45 angle. (). 2. Push the top of the cantilever downward. (). 45 If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-09

15 Footprint Assembly Instructions Page 2 of 2 (continued) Figure E Note: Cantilevers are required with corner surfaces. (Figure D) With use of split top corner surface, corner cantilevers must be located under adjacent surfaces. (Figure E). Cantilevers can be used as required support when open kneespace is greater then 48" for 1 3/16" surfaces and 60" for 1 9/16" surfaces. (Figure F). 3. Attach worksurfaces with flat brackets and adjust alignment, if applicable. 4. Attach cantilever to worksurface with screws provided. Five screws required per bracket. Figure D Figure F Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-09

16 Footprint Assembly Instructions Page 1 of 2 Worksurface Cantilever Bracket for Interworks EQ Panel Drill with Torque Option Tape Measure #R-2 Square Srewdriver Bit Level Rubber Mallet Package Contents #8 x.75 Robinson Head Flakeboard Screw Standard Height 24" General Information Cantilevers are required when placing two surfaces end to end, when open kneespaces are greater than 48" for 1 3/16" surfaces or 60" for 1 9/16" surfaces, or in configurations where standard panel worksurface bracket support is not possible. Cantilevers are designed so that a single bracket can share the load between two adjacent surfaces. They can be used as sole support for a worksurface. The top of the cantilever should be located 24" from the bottom of fabric for standard height (29" nominal). (). 1. Insert hook on the top of cantilever into the slot on panel siderail at a 45 angle. (). 2. Push the top of the cantilever downward. (). Important: Use mallet to make sure bracket is seated and fully engaged If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision D-09

17 Footprint Assembly Instructions Page 2 of 2 (continued) Figure E Note: Cantilevers (with cutout to inside) are required with corner surfaces. (Figure D) With use of split top corner surface, corner cantilevers (with cutout to outside) must be located under adjacent surfaces. (Figure E). Cantilevers can be used as required support when open kneespace is greater then 48" for 1 3/16" surfaces and 60" for 1 9/16" surfaces. (Figure F). 3. Attach worksurfaces with flat brackets and adjust alignment, if applicable. 4. Attach cantilever to worksurface with screws provided. Figure D Figure F Printed in U.S.A Kimball International, Inc. Kimball Office T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision D-09

18 Systems Assembly Instructions Footprint Page 1 of 3 Worksurface End Panel Drill with Torque Option Tape Measure #2 Phillips Head Bit Level 6" Magnetic Phillips Tip Bit or, Screwdriver Package Contents #10 x 1" Phillips Panhead #10 x 1" Hex Washer Head Particleboard Screws Drill Tip Screws x 3 4" Round Head Machine Screws - End Panel/Worksurface Brackets 1. Smooth side should be facing away from the worksurface being supported by the end panel. 2. Two L-shaped end panel/surface brackets secure end panel to worksurface. 3. Determine whether end panel will be left or right. Relocate glides as needed. 4. Place end panel smooth side down, glides closest to you. 5. Locate pre-drilled holes for attaching end/panel surface brackets. Secure end panel/surface brackets to end panel using #10x 1 2" screws. (). Note: Hole patterns differ for full end and half end panel. General Information These instructions provide the basic information needed to install any metal end panel into an Interworks EQ panel. Corner worksurfaces are predrilled to accept End Panel for installation in standard flush left/right position. process is similar for both half end panel (18"D) and full end panel (24", 30"D). Full end panel is illustrated. Unsupported worksurface span must not exceed 60". Kimball will not assume liability for any improperly or inadequatedly supported worksurface. Instructions are provided to install worksurface at standard desk height (28³ ₁₆" actual height). End panel is designed to secure (): a) Surface and panel at end of run when no wing panel is used or when undersurface is less than full depth/height. b) Surface and panel when full height undersurface support is required, e.g. with some corner applications. End panel can be used to share load between two surfaces. (See Page 3). a) b) Sample Configurations (Brackets indicated by dotted lines) If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-07

19 Systems Assembly Instructions Footprint Page 2 of 3 - End Panel/Side Rail Tie Brackets 1. Two reversible end panel/side rail tie brackets seucre end panel to panel side rail. 2. Rear of end panel is open to accept two tie brackets. A notch in the opening corresponding to the width of the tie bracket. Internal structure of end panel has threaded nuts for installation of tie brackets. 3. Locate notches in rear of end panel. Insert bracket, hooks facing away from rear of end panel, flush against the notch at the rear of the end panel. 4. Using a minimum of 6" magnetic Phillips tip bit/screwdriver, secure brackets to end panel using 1 4"-20 screws, provided. (). End Panel to Panel, Worksurface 1. Place end panel in desired location and insert hooks on brackets into panel side rail. (Figure D). Hooks are designed to engage the side rail slots in the up position; extend End Panel glides to secure End Panel. 2. Place worksurface on top of End Panel. Square and level, readjusting End Panel glides as needed. Front edge worksurface should be slightly recessed from front edge of panel side rail. Rear edge surfaces are flush against the panel. 3. You may or may not want to secure End Panel to surface just yet, depending on other brackets and undersurface storage being installed. Tip: All surfaces should be in place, squared and level before you screw in brackets to surfaces. This makes any minor adjustments easier. Note: When undersurface storage is installed adjacent to End Panel, storage and End Panel may be secured to worksurface at the same time through aligned holes in storage and End Panel/Surface Brackets. (Figure E). 4. Secure End Panel/Surface Brackets to worksurface using (four) #10x1" screws provided per bracket. Figure D Figure E (Rear view) Spacers If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-07

20 Footprint Systems Assembly Instructions Page 3 of 3 - One end panel to support two worksurfaces 1. Additional set of End Panel/Surface Brackets is required. Contact Customer Care to order. 2. Install all (four) End Panel/Surface Brackets to End Panel, two per side. End Panel is predrilled on one side. To mark smooth side, measure hole patterns on pre-drilled side and transfer to smooth side. Drill holes. 3. Insert bracket, hooks facing away from rear of End Panel, flush against the notch at the rear of the End Panel. (Figure F). 4. Place end panel in desired location and insert hooks on the brackets into panel side rail. End panel should be centered on panel hinge. (Figure G). 5. Extend End Panel glides to secure End Panel. 6. Place surfaces onto End Panel (and other installed brackets). Ensure it is level and square. 7. Secure End Panel/Surface Brackets to surface using (two) #10x1" screws provided per bracket. Figure F Figure G (Rear view) (Rear view) Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-07

21 Universal Products Casegoods Assembly Instructions Page 1 of 1 Support Bases #2 Phillips Head Bit Tape Measure Screw Gun 12" D 6" D 12" D Hardware Required #8 x ⁵ ₈" Panhead #8 x 1" Flathead Bracket 1. Support bases are used to provide support for any worksurface shape. (). 2. To install, place worksurface on a clean, soft surface, underside facing up. Mark the center of the radius where the base attaches. Attach base to worksurface using #8 x 1" flathead screws and the #8 x ⁵ ₈" panhead screws provided. (). #8 x 1" Flathead Screw Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Care. Part No Revision E-04

22 Universal Products Casegoods Assembly Instructions Page 1 of 1 Cylinder Base Equal distance all around #2 Phillips Head Bit Tape Measure Screw Gun Level Hardware Required #8 x ⁵ ₈" Panhead #8 x 1" Flathead 1. Place top face down on a clean, solid surface or floor. Position base on top so that it is centered and there is an equal distance from the base to the edge of the top all around. (). 2. Attach base to top as shown using six (6) #8 x 1" flathead screws and six (6) #8 x ⁵ ₈" panhead screws provided. (). 3. Carefully turn table right side up. Level unit by extending the adjustable glides (turn counterclockwise), located in the cylinder base bottom panel, as required. (). Top Cylinder Base #8 x 1" Flathead Screw (6 required) Adjustable Glide (6) Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Care. Part No Revision B-04

23 Assembly Instructions Footprint 1 Column Base Drill with #2 Phillips tip bit Level Hardware Provided The Column Base provides the main support for the top. D Shape, U Shape and Extended U Shape worksurfaces are predrilled for Column Base installation (). 1. Turn worksurface upside down. 2. Locate pre-drilled holes for attaching Column Base. 3. Lay Column Base on worksurface and secure using four #10x1" screws (). 4. Position worksurface and check for square and level. Adjust Column Base by pressing both buttons and sliding lower leg so buttons engage holes nearest level position (). 5. For final adjustment, turn large glide at bottom of column leg (Figure D). #10x 1" Phillips pan head particleboard screw. WORKSURFACE DESIGNED FOR COLUMN LEG Interworks style illustrated U Shape worksurface illustrated Figure D D Shape U Shape (Full Radius and Crowned) Extended U Shape Adjust by pressing buttons and raising/lowering leg If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision -

24 Assembly Instructions Footprint 1 Decorative Support Leg Drill with #2 Phillips tip bit Level Pencil WORKSURFACE DESIGNED FOR COLUMN LEG Hardware Provided #8 x 3/4" Phillips pan head drill screws (provided). D Shape U Shape (Full Radius and Crowned) Extended U Shape General Information These instructions provide the basic information to install a Decorative Support Leg onto any Footprint worksurface. The Decorative Support Leg provides the main support for the top. A Privacy Panel can be secured to Decorative Support Leg. Refer to Decorative Support Leg Assembly Instruction. D Shape, U Shape and Extended U Shape worksurfaces shown (). Turn worksurface upside down. Using a pencil, sketch two lines as shown (). One line from the tangent points of the round, and one centered on the worksurface. Place Decorative Support Leg onto worksurface, center the leg over the intersection of the sketched lines as shown (). NOTE: Be sure to position Decorative Support Leg so that the side with weld-beading faces inward. 4. Secure Decorative Support Leg to undersurface using ten #8 x 3/4" screws (Figure D). Position worksurface and check for square and level. Adjust by turning glides at the base of the Decorative Support Leg. U Shape worksurface illustrated Figure D If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision -

25 Footprint Worksurfaces D Shape Systems Assembly Instructions Page 1 of 1 Level Drill with #2 Phillips Tip Bit Tape Measure Rubber Mallet Package Contents #10x1" Phillips Pan Head Particleboard Screws Adjustable Column Base Decorative Support Leg Cantilever Brackets Half End Panels General Information These instructions provide the basic information needed to install a D shape worksurface into an Interworks panel. D shape must be supported by an adjustable column base or a decorative support leg. (). In any systems applications, D shape worksurface must be tied into the two adjacent worksurfaces. Cantilever brackets or half end panels can be used. (). Worksurfaces are predrilled to accept bracket installation in Cantilever Brackets standard flush left/right position. Unsupported worksurface span must not exceed 48". Kimball will not assume liability for any improperly or inadequately supported worksurface. Cantilever Brackets Instructions are provided to install worksurface at standard desk height ( " actual height). One person can perform all operations. 1. Turn worksurface upside down. Install adjustable column base or decorative support leg first. See Support Column Base or Worksurfaces, Decorative Support Leg assembly instructions. 2. Install cantilevers or half end panels into adjacent panels and position adjacent surfaces. (). See Worksurfaces, Cantilever Bracket or Worksurfaces, End Panel assembly instructions. 3. Install flat brackets to adjacent surfaces so that half of the bracket extends to support D shape worksurface. 4. Position D shape worksurface onto flat brackets and align front edges of surfaces to be flush. 5. Secure all brackets with screws provided. Half End Panels Flat Brackets Half End Panels Flat Brackets Printed in U.S.A Kimball International, Inc. T F If you have any questions concerning these instructions, please call Kimball Office Customer Service. Part No Revision C-07

26 Assembly Instructions Footprint 1 Quarter Round Worksurface Drill with #2 Phillips tip bit Tape measure Rubber mallet Cantilever Bracket Flat Brackets Cantilever Brackets Hardware Provided #10x1" Phillips pan head Fiberboard screws (provided with supports) General Information These instructions provide the basic information needed to install any Footprint Quarter Round Worksurface into an Interworks EQ panel. In systems applications, Quarter Round Worksurface must be tied into adjacent worksurfaces. Cantilever Brackets or Half End Panels can be used (). Adjustable Column Base or a Decorative Support Leg may be used to provide additional support to Quarter Round Worksurface (). Half End Panel Flat Brackets Cantilever Bracket Decorative Support Leg (optional) Half End Panel Half End Panels Turn Worksurface upside down. Install Adjustable Column Base or Decorative Support Leg first. Install Cantilever(s) or Half End Panel(s) into adjacent panels and position adjacent surfaces (). Install Flat Brackets to adjacent surfaces so that half of the bracket extends to support Quarter Round Worksurface. Position Quarter Round Worksurface onto Flat Brackets, secure the Quarter Round to adjacent surfaces, making sure there are no gaps in between. Then secure the adjacent surfaces to their support brackets. Cantilever Bracket Flat Brackets Half End Panel Cantilever Brackets And Half End Panels Adjustable Column Base (optional) Cantilever Brackets Half End Panels Adjustable Column Base Decorative Support Leg If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision -

27 Assembly Instructions Footprint 1 Gusset Bracket 5/16 Hex Head Bit Level Hardware Provided #8x3/4 Phillips pan head Fiberboard screws (provided) #10x1/2 Hex Head Self Tapping screws (provided) General Information Gusset Bracket is non-handed. Gusset Bracket is designed for use with a Worksurface Support Panel, Return Support Panel or Privacy Panel, all of which are predrilled for bracket attachment (). It can also be used with an End Panel, which is not predrilled, e.g. to create a "freestanding" table. One person can perform all operations. to End Panel Locate two vertical holes in End Panel for attaching Modesty Panel. These holes indicate the location of the substructure inside the End Panel. Measure distance from these holes to closest edge of End Panel, approximately 4 1/8". Mark same distance at opposite side of End Panel (Figure D). Place first Gusset Bracket against End Panel, in-line with pre-drilled holes. Mark Gusset Bracket hole locations and install Gusset Brackets with three #10x1/2 Hex Head Self Tapping screws per bracket. Check for vertical plumb of Gusset Brackets and secure each to worksurface using three #8x3/4 Phillips pan head Fiberboard screws each bracket. to Support Panel Install Support Panel to worksurface (see Support Panel AI). Align holes in Gusset Bracket to corresponding holes in Support Panel and secure using three #10x1/2 Hex Head Self Tapping screws (). Secure Gusset Bracket to worksurface using three 10x1 Phillips pan head Fiberboard screws. to Privacy Panel Position Gusset Bracket into inside flange of Privacy Panel. Secure with two #10x1/2 Hex Head Self Tapping screws (). Ensure Privacy Panel is still perpendicular to Decorative Support Leg and secure Gusset Bracket to worksurface using three #8x3/4 Phillips pan head Fiberboard screws. Figure D Gusset Brackets are installed approximately 4 1/8 inset from edges of End Panel Privacy Panel Return Support Panel End Panel If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision -

28 Pedestal Filler Strip, TRAXX Pedestal Filler Strip Assembly Instruction General Information These instructions provide the basic information to install a Pedestal Filler Strip or Traxx Pedestal Filler Strip onto a worksurface-supporting Interworks Pedestal (). Traxx Pedestal Filler Strip is non-handed; Pedestal Filler Strip is left- or right-handed (). Designed for use with the Interworks Pedestal and either Interworks systems or modular surface or ICS systems surface. Interworks systems surfaces are illustrated. When Interworks systems surface is used, a wire management gap at the rear of the worksurface occurs and may be concealed with a Wire Manager Fill Cap. Traxx Pedestal Filler Strip (non-handed) Pedestal Filler Strip One person can perform all operations. Hardware Drill with #2 Phillips tip bit #8x 3 /8" thread cutting screws Spacers included with storage units 1. Filler Strip is secured to either the left or right rear of the Pedestal (). NOTE: Pedestal Filler Strip only (panel application): Hooks engage into panel side rail and should be pointing UP. 2. Secure Filler Strip to Pedestal using six #8x 3 /8" thread cutting screws, three each at the top and bottom. 3. Level Pedestal glides to set hooks in Pedestal Filler Strip or as needed. See #HAIIWS002. Make sure smooth side of Filler Strip is facing out to enclose vertical reveal Traxx applications Panel applications If you have any questions concerning these instructions, please call your Customer Care Team. Tel Fax Form No. HAIIWS007B-02 Printed in U.S.A Kimball International, Inc. 1

29 MODULAR CASEGOODS Interworks Desks Assembly Instruction Modular Casegoods Planning These instructions provide the basic information to assemble Interworks freestanding modular casegoods. To reduce installation time, it is recommended you install modular casegoods in the following order: 1. Pedestal 2. End Panel 3. Modesty Panel 4. Undersurface Lateral File or File Center General Information Worksurfaces accept Pedestal or End Panel in standard position flush left or flush right only (). Rectangular worksurfaces are illustrated. Four Spacers are included with all Pedestals and Undersurface Lateral Files. These ARE NOT used unless freestanding unit is part of systems installation, e.g. a freestanding return joined to a systems top. One person can perform all operations, although two may be required to handle larger, heavier units. Removing Drawers To remove Pedestal Box and Undersurface Lateral File drawers (): 1. Begin with top drawer (). Extend drawer fully. 2. Insert flat head screwdriver in between pedestal drawer and slide. Pry slide away from drawer slightly (). 3. Put one hand underneath drawer. Lift front of drawer up to disengage from front drawer slide channel hooks. 4. When front of drawer is disengaged, pull entire drawer towards you, supporting it from the bottom. This should disengage drawer from rear drawer slide channel hooks. 5. Set all drawers aside and slide drawer channels back into case. Do not try to remove the entire drawer slide. Pedestal Box Drawer File Center File Drawer Hardware Drill with 1 /8" and #2 Phillips tip bits 5 /16" Hex socket Level Measuring tape Flat head screwdriver Metal to worksurface: #10x1" Phillips pan head particleboard screws. Metal to metal: #10x 1 /2" Hex washer head drill screws. File Drawer Lateral File Drawer TYPICAL APPLICATIONS Double Pedestal Desk Single Pedestal Desk/Return Pedestal/Undersurface Lateral File 3. If you have any questions concerning these instructions, please call your Customer Care Team. Tel Fax Form No. HAIIWFS001E-01 Printed in U.S.A Kimball International, Inc. 1

30 Removing Drawers Figure D To remove File drawer: 1. Extend drawer fully (Figure D). 2. Each drawer slide has a lever: one is depressed, the other is lifted. Simultaneously while lifting and depressing the levers, hold drawer level and pull drawer toward you. This should disengage drawer from File Center unit. Lever 3. Set drawer aside and slide drawer channels back into case. Do not try to remove the entire drawer slide. Pedestal Drill for Modesty Panel Inside each Pedestal, there are two front and two rear uprights or vertical channels. In the front flange of the rear upright, look for locator holes where Modesty Panel will attach (Figure E). 1. Facing the Pedestal, determine where the Modesty Panel will attach to the Pedestal: on the left or right side. 2. Drill the four holes, left OR right, using a 1 /8" bit. NOTE: If future reconfiguration is expected, a Pedestal Non- Deface Kit can be ordered to attach Modesty Panel to the Pedestal without drilling into the Pedestal. Contact Customer Care. Figure E Hole locations (4) Modesty Panel (in grey/dotted lines) Rear upright Front of Pedestal Pedestal Securing to Worksurface 1. Place worksurface flat on level ground, with front of worksurface closest to you. 2. Secure two #10x1" screws into worksurface where Pedestal will be installed. DO NOT tighten screws all the way down; leave about 1 /4" of the screw head exposed. 3. Turn Pedestal upside down and place it on its side. Tilt Pedestal upright and onto installed screws. Align front and rear keyholes in Pedestal with screws (Figure F). 4. Adjust Pedestal position inset 1 /8" from rear edge of top. If Pedestal is less than full depth with a planned overhang, inset to a position 1 /8" from front edge of top. 5. Use remaining keyholes to secure Pedestal to worksurface with remaining two screws and tighten all screws down fully. Figure F Keyholes in Pedestal align to screws in worksurface 2 MODULAR CASEGOODS

31 End Panel Information Refer to Figure G. Full End Panels include brackets for attaching to worksurface. Return Support Panels are less than full depth and secure directly to the worksurface. They are used to create a return. All end panels are predrilled to secure Modesty Panel. NOTE: Install Full End Panel first, since it is fully loadbearing. When installing Return Support Panel, use caution in turning assembled worksurface upright, since it is less than full depth support. Figure G Return Support Panel Flush side Hollow side Predrilled holes for modesty panel Full End Panel Smooth side Pre-drilled side End Panel 1. Determine location of support, left or right. Relocate the two glides to the opposite side of support as needed. 2. Inset End Panel approximately 1 /8" from front and back of worksurface and approximately 1 /16" from side of worksurface. Secure front and rear End Panel/Worksurface Brackets to worksurface with four #10x1" screws per bracket (Figure H). 3. Turn End Panel upside down and align to installed brackets. Holes in the End Panel should be to the INSIDE and the glides should be facing UP. Secure loosely with two #10x 1 /2" screws (Figure I). NOTE: After you have installed the Modesty Panel, you will come back and retighten all screws. Figure H Figure I Glides Return Support Panel 1. Determine location of support, left or right. Relocate the two glides to the opposite side of support as needed. NOTE: Modesty Panel attaches to the flush side of support. Therefore, hollow side should be facing out, toward user. 2. Secure Return Support Panel directly to worksurface with two #10x1" screws. It should be 1 /8" inset from rear corner, finished side facing in (Figure J). Figure J Return Support Panel Flush side faces inward, providng necessary surface for attaching Modesty Panel Hollow side faces outward MODULAR CASEGOODS 3

32 Modesty Panel Modesty Panel is mounted 1 1 /2" from worksurface, 3" from floor, and 3" from rear edge of worksurface. From approach side of desk, Modesty Panel is visibly inset. 1. Align Modesty Panel to Pedestal first. Finished side of Modesty Panel should be facing out (Figure K). 2. Secure one end of Modesty Panel to Pedestal with four #10x 1 /2" screws. 3. Secure other side of Modesty Panel to End Panel, Return Support Panel or second Pedestal. 4. Retighten all screws, beginning with Modesty Panel screws and working your way out to Pedestal, End Panel, Return Support Panel. Figure K Modesty Panel Finishing Up To finish installation, turn completed modular unit upright. 1. Level unit. Tip back and adjust glides on Pedestal, End Panel or Return Support Panel. 2. Inset End Panel approximately 1 /8" from front and back of worksurface and approximately 1 /16" from side of worksurface. Once a basic shell is assembled, you are ready to install Undersurface Lateral File/File Center (or less-than-full depth Pedestal if Full End Panel is also used on that side). 3. Remove drawers of storage (see Page 1). 4. Slide storage under assembled modular unit, adjusting glides as needed. Front edge should be flush with other installed support. 5. Secure storage to underside of worksurface with four #10x1" screws through keyholes in top of storage. 6. Return can be secured to other unit with Flat Brackets (Figure L). NOTE: Flat Brackets are not included with modular worksurfaces; contact Customer Care to order. Or, if you are installing systems worksurfaces, you may have additional Flat Brackets remaining. 7. Reinstall drawers into Pedestals, Files. Figure L 4 MODULAR CASEGOODS

33 Assembly Instructions Footprint 1 Modesty Panel Drill with 1/8" #2 Phillips tip bit 5/16" Hex socket or Hex drill bit Level 3/16 head wrench Hardware Provided Metal to metal: #10x 1/2"Hex washer head drill screws (provided). 1. Modesty Panel is mounted 1 1/2" from top of worksurface,3" from floor, and 3" from rear edge of worksurface. From approach side of desk, Modesty Panel is visibly inset. 2. Facing the Pedestal, determine where the Modesty Panel will attach to the Pedestal: on the left or right side. Remove Pedestal drawers (see Remove Pedestal Drawer Assembly Instruction). 3. Inside each Pedestal are two front and two rear uprights. In the front flange of the rear upright, look for locator holes where Modesty Panel will attach (). Drill the four holes, left OR right, with an 1/8" bit. NOTE: If future reconfiguration is expected, a Pedestal Non-Deface Kit (IFMDF) can be ordered to attach Modesty Panel to the Pedestal without drilling into it. 4. With finished side facing out, secure one end of Modesty Panel to Pedestal with four #10x 1/2" screws (). 5. Install End Panel or Support Panel to worksurface (see Attach End Panel/Support Panel Assembly Instruction) or second Pedestal and secure Modesty Panel using screws provided. Return Support Panel illustrated (). 6. Retighten all screws, beginning with Modesty Panel and working your way out to Pedestal and end panels. If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision -

34 Assembly Instructions Footprint 1 End Panel Drill with 1/8" #2 Phillips tip bit 5/16" Hex socket Level Hardware Provided Metal to worksurface: #10x1" Phillips pan head particleboard screws. Metal to metal: #10x1/2"Hex washer head drill screws. General Information For Rectangular and non-standard position, worksurface must be drilled. Process is similar for both Full and Half End Panel. Full End Panel is illustrated. Half End Panel is often used to create a freestanding Corner desk. When an Undersurface Lateral File is used, a Full End Panel is required to support desk on the same side as the File. End Panel End Panels include brackets for attaching to worksurface and predrilled holes to secure Modesty Panel (). 1. Determine location of End Panel, left or right. Relocate the two glides to the opposite side of support as needed. 2. Align inside of Worksurface Brackets to pre-drilled holes on End Panel (). Attach brackets to End Panels using 2 1/2 screws into the pre-drilled holes. Secure the brackets with 2 more 1/2 screws. 3. Inset End Panel approximately 1/8" from front and back of worksurface (back only with the Arc worksurface), and approximately 1/16" from side of worksurface. Secure front and rear End Panel/Worksurface Brackets to worksurface with four #10x1" screws per bracket (). If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision -

35 Assembly Instructions Footprint 1 Freestanding Corner Tape Measure Drill with #2 Phillips tip bit 5/16 Hex socket Level Hardware Provided Metal to wood (worksurface): #10x1" Phillips pan head drill screws. Metal to metal: #10x 1/2"Hex washer head drill screws. General Information Install Modesty Panel to Half End Panel Half End Panels and Modesty Panel are both pre-drilled. Modesty Panel is mounted 1 1/2" from top of worksurface, 3" from floor, and 3" from rear edge of worksurface. 1. Turn Modesty Panel perpendicular to Half End Panel, finished face of Modesty Panel away from you (). 2. Align holes in flange of Modesty Panel to holes in Half End Panel and secure with four #10x 1/2" screws provided. 3. Repeat for right Half End Panel. These instructions provide the basic information to create a Footprint freestanding corner desk. Corner desk consists of: Corner worksurface, two Half End Panels, two Modesty Panels, one Corner Support post. Install Bracket to Half End Panel Half End Panels are secured to worksurface via two L-shaped brackets, which are attached to inside face of End Panel via pre-drilled holes. It is easier to install Half End Panels to worksurface with the L-shaped brackets already attached. 1. Designate Half End Panels as left and right: Lay Half End Panels side-by-side as in. Glides should be facing you (unscrew and relocate as needed). 2. Starting with left Half End Panel, secure brackets into predrilled holes in End Panel with two #10x 1/2" screws provided per bracket (, inset). Flange of bracket should be flush with top of Half End Panel. 3. Repeat with right Half End Panel. Install Half End Panel Assembly to Worksurface 1. Turn worksurface upside down, user edge nearest you. 2. Align Half End Panel (with Modesty Panel attached) flush to rear edge of corner worksurface (). 3. Secure brackets to worksurface with four #10x1" screws per bracket provided. 4. Repeat for other Half End Panel. If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision -

36 Footprint 2 Freestanding Corner Install Corner Support to Worksurface, Modesty Panel Once Half End Panels (with Modesty Panel attached) are installed, it is easier to position Corner Support post. 1. Position Corner Support post where Modesty Panels come together (Figure D). Glide should be facing up. 2. Secure each Modesty Panel to Corner Support post at vertical flange using four #10x 1/2" screws provided. 3. Secure Corner Support post to worksurface using four #10x1" screws provided, two per flange (Figure D, inset). Finishing Up 1. Turn completed corner desk over (Figure E). 2. Check for level. Adjust glides on End Panels and Corner Support post as needed. 3. Space in front of Half End Panels can be used to tie corner unit into adjacent freestanding units with Flat Brackets (ordered separately). Figure D Assembly Instructions If you have any questions concerning these instructions, please call Kimball Office Customer Care Revision -

Definition Assembly Instructions

Definition Assembly Instructions Definition Assembly Instructions 1998752 Revision A-12 Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 2012 Kimball International,

More information

Footprint Mobile Assembly Instructions

Footprint Mobile Assembly Instructions Footprint Mobile Assembly Instructions 1998754 Revision -1 Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 20 Kimball

More information

LF Series Assembly Instructions

LF Series Assembly Instructions LF Series Assembly Instructions 1998760 Revision A-10 Complete Series Master Packet 2010 Kimball International, Inc. T 800.482.1818 F 812.482.8300 Footprint Storage and Metal Filing Systems Assembly Instructions

More information

STAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS

STAKS. Crossover Casegoods ASSEMBLY INSTRUCTIONS STAKS Crossover Casegoods ASSEMBLY INSTRUCTIONS Installation Sequence 1. Wall Panels a. Connector Kit Part Identification 3 b. T - 3 Panel Connection Preparation 4 c. X Panel Connection Preparation 5 d.

More information

Topo Freestanding Applications - Private Office

Topo Freestanding Applications - Private Office 4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com

More information

Linear Hook- on Worksurfaces

Linear Hook- on Worksurfaces Linear Hook- on Worksurfaces Linear Hook-On Worksurfaces come in three depths and seven lengths. Different worksurfaces have different reqirements for installation that are outlined below. 27 inch deep

More information

Perks Assembly Instructions

Perks Assembly Instructions Perks 2066779 Revision A-10 Complete Series Master Packet 2008 Kimball International, Inc. T 800.482.1818 F 812.482.8300 Perks Page 1 of 1 Mobile Screens Starter Screen Hex Head Wrench Rubber Mallet Package

More information

OXYGEN INSTALLATION. Revision date

OXYGEN INSTALLATION. Revision date 12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex

More information

compile system INSTALLATION GUIDE Updated January 2019

compile system INSTALLATION GUIDE Updated January 2019 INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness

More information

Figure A. Figure B. Figure C. Figure D

Figure A. Figure B. Figure C. Figure D Xsite 1 Power/Data Tile and Components Tools Required Tape Measure Cordless Drill/Driver #2 Phillips Screw driver bit Rubber Mallet Flat Blade Screwdriver Figure A Hardware Required Provided as shown Installation

More information

Workbench Instructions for Assembly

Workbench Instructions for Assembly Workbench Instructions for Assembly Technical Electronic Workstations and Industrial Workbenches Includes: Cabinets Privacy Panels Stringers Bottom Shelves Table of Contents Tools Required for Assembly...

More information

ZAPF PANEL SYSTEM ASSEMBLY INSTRUCTIONS. It is recommended that the components be installed in the sequence of this assembly manual.

ZAPF PANEL SYSTEM ASSEMBLY INSTRUCTIONS. It is recommended that the components be installed in the sequence of this assembly manual. ZAPF PANEL SYSTEM It is recommended that the components be installed in the sequence of this assembly manual. ASSEMBLY INSTRUCTIONS OFFICE FURNITURE FOR THE INFORMATION AGE Table of Contents INSTALLATION

More information

Product must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product.

Product must be installed as shown using the screws and brackets provided. Use of incorrect hardware could result in damage to the product. General Notes These installation instructions are intended to be comprehensive for a typical Keyeira/Presto configuration. Your configuration may differ. If you have questions contact Geiger Customer Service

More information

Assembly Instructions

Assembly Instructions InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective

More information

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding

More information

Range height adjustable assembly

Range height adjustable assembly Table of contents Digital handset operation 3 Height adjustable bench kit 4-5 Cable carrier 6 Ganging tray and ganging rail 7 Height adjustable return frame kit 8 Cable entry pole 9 24 and 30 d worksurfaces

More information

Modular Bi-File Lateral

Modular Bi-File Lateral Modular Bi-File Lateral Installation Instructions 920-563-6362 E-mail: ssc@spacesaver.com Internet: www.spacesaver.com Contents Hardware Identification..................................3 Pre-Installation........................................6

More information

Right. Side Tower-Overhead Combination Revised 11/12/05 ON SITE A,B D,E C

Right. Side Tower-Overhead Combination Revised 11/12/05 ON SITE A,B D,E C Right ON SITE Side Tower-Overhead Combination Revised 11/12/05 2 Installation of Side Tower-Overhead Combination units is easy when the correct SEQUENCE is followed. 3 Your unit consists of the following

More information

Oxford Stalls Installation Instructions

Oxford Stalls Installation Instructions Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or

More information

RANGE DIGITAL HANDSET OPERATION. 1. Panel. 2. Initialization Procedure. 3. Move Up & Down. 4. Set Memory Positions. 5. Move to the Memorized Positions

RANGE DIGITAL HANDSET OPERATION. 1. Panel. 2. Initialization Procedure. 3. Move Up & Down. 4. Set Memory Positions. 5. Move to the Memorized Positions INSTRUCTION SHEET #2577INS PART #1730534 DIGITAL HANDSET OPERATION OPERATION INSTRUCTIONS 1. Panel 1 Button: Preset 1 2 Button: Preset 2 3 Button: Preset 3 S Button: Select Display: Reads in 1 / 2 " Increments

More information

Assembly Instructions

Assembly Instructions 10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions

More information

Revised

Revised Indentify Non-powered panels and separate from Powered panels. Non-powered panel shown at left.. Powered panel shown at left has powerway mounted at factory. Also separate panels by surface type, width

More information

INSTRUCTION BOOKLET #C20

INSTRUCTION BOOKLET #C20 INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO

More information

INSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE

INSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

Workbench Instructions for Assembly

Workbench Instructions for Assembly Workbench Instructions for Assembly FlexWorks is a trademark of Lista International Corporation. Making Workspace Work is a trademark of Lista International Corporation. Document Number: MD002A3 Print

More information

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013

CONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013 U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

MobileTrak5 Installation Instructions

MobileTrak5 Installation Instructions MobileTrak5 Installation Instructions PLEASE OPEN ALL BOXES & CHECK TO MAKE SURE YOU HAVE ALL PIECES REQUIRED READ ALL INSTRUCTIONS BEFORE STARTING Tools Required for Assembly 7/16, 1/2 Wrench Phillips

More information

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the

IMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding

More information

APTOS DUOFOIL LEGS DRILL 1/8" DRILL BIT. Rev: Dwg: DUOFOIL LEGS DRILL DUOFOIL LEGS AT A 45 ANGLE TO EDGE OF TOP WITH WIRE CAVITY

APTOS DUOFOIL LEGS DRILL 1/8 DRILL BIT. Rev: Dwg: DUOFOIL LEGS DRILL DUOFOIL LEGS AT A 45 ANGLE TO EDGE OF TOP WITH WIRE CAVITY PART # 1711258 INSTRUCTION SHEET # 2555INS Dwg: Rev: DUOFOIL LEGS DRILL DUOFOIL LEGS DRILL 1. Check bottom side of top for pre-bored mounting holes. (If done, move to Step 4.) TAPE MEASURE STEP 1: CHECK

More information

Interra Installation Manual

Interra Installation Manual Interra Installation Manual Instructions to install the Friant Interra panel system Friant & Associates, LLC Table of Contents Getting Started Introduction... 3 General Tools, Staging & Safety... 4 Before

More information

bridges Installation Manual

bridges Installation Manual bridges Installation Manual 0 OHSAS 800:007 CGSB #0HS-009 ISO 900:008 CGSB #96- ISO 00:00 CGSB #EMS-00 Global Contract Inc. 6 Petrolia Road North York, Ontario, MJ X8 Visit us on the Internet at globalcontract.com

More information

SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide

SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide SmartView Mounting Frame 3 Wide x 3 Deep Video Wall Display Installation Guide WMK-034 This display kit mounts ViewSonic 46 Video Wall displays in a 3 wide by 3 deep landscape configuration. The frame

More information

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16

Equilibrium. Conference Table. Installation Instruction. Revision B 11/07/16 Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete

More information

Franklin Mills Stackable Movable Lateral Instructions

Franklin Mills Stackable Movable Lateral Instructions Franklin Mills Stackable Movable Lateral Instructions Table of Contents: Table of contents...1 Tools Required...2 Stationary Shelving Assembly...3-7 Mobile Shelving Assembly...8-16 Rail Assembly...8-11

More information

Queen Wingback Bed King Wingback Bed

Queen Wingback Bed King Wingback Bed Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock

More information

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)

GlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

Angled Side Flush with Panel Face

Angled Side Flush with Panel Face Identify and sort panels by like sizes, fabrics, surface type (tackable vs hard), and NON- POWERED vs POW- ERED. Non-powered panels ship without a powerway. Powered panels include a powerway. See below.

More information

Desk/Wall-Mount Rack

Desk/Wall-Mount Rack Desk/Wall-Mount Rack Patent(s) Pending Installation Instructions Post P/N: 119-1752 119-1781 119-1782 119-4014 Frame P/N: 119-1591 119-1754 119-1755 Kit Contents (2) Frames (4) Posts Assembly Hardware

More information

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly

More information

AFCO-Rail Post INSTALLATION INSTRUCTIONS AFCO-RAIL POST

AFCO-Rail Post INSTALLATION INSTRUCTIONS AFCO-RAIL POST AFCO-Rail Post INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Drill Bits (for the appropriate fastener) Drill (with adjustable clutch, recommended) Level String Line Tape Measure Tools to install fasteners

More information

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.

TOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER. TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support

More information

TrendWall Floor-To-Ceiling Panels Installation Instruction

TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster

More information

ROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door

ROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are

More information

a.k.a. casegoods instructions

a.k.a. casegoods instructions a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly

More information

Parts Included: Tools Required: Canvas Office Landscape Interiors Off Module 90 Connector Kit Installation and Disassembly for Recycling Instructions

Parts Included: Tools Required: Canvas Office Landscape Interiors Off Module 90 Connector Kit Installation and Disassembly for Recycling Instructions Y Parts Included: Canvas Office Landscape Interiors Off Module 90 Connector Kit Installation and Disassembly for Recycling Instructions FT127.A N Shim A Light Seal B Foam Light Seal C G H Double-Face Tape

More information

Series 4 HV Single Monitor Lift Assembly Instructions

Series 4 HV Single Monitor Lift Assembly Instructions 6703 Zinser Street Schofield, WI 54476 6/13/17 Series 4 HV Single Monitor Lift Assembly Instructions Read all the instructions before beginning. Hardware Pack # 53368 Page1 OF 6 Tools Required for Assembly:

More information

Important Loading Information. Tools Required. Meridian Lateral Files Instructions

Important Loading Information. Tools Required. Meridian Lateral Files Instructions Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information

More information

Assembly Instructions 10 X 10 Aluminum Frame Building

Assembly Instructions 10 X 10 Aluminum Frame Building Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

3 wide x 3 deep Video Wall Display Installation Guide

3 wide x 3 deep Video Wall Display Installation Guide HoverTrack Series 3 wide x 3 deep Video Wall Display Installation Guide VWD-3X3-X462 This display kit mounts NEC X461UN and X462UNS LCD monitors in a 3 wide by 3 deep landscape configuration. The frame

More information

Installation Instructions - Model V4JSD 1

Installation Instructions - Model V4JSD 1 Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)

More information

Copyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax

Copyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax Copyright 2003. Black Box Corporation. All rights reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 JULY 2003 RM3010A RM315-R2 RM323-R2 RM329 RM451 RM457 RM3020A RM316 RM324-R2

More information

User Instructions Multiline Otter Scoreboard Caddy Assembly

User Instructions Multiline Otter Scoreboard Caddy Assembly List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)

More information

PROFILE Flat Panel Console System Installation Manual

PROFILE Flat Panel Console System Installation Manual PROFILE Flat Panel Console System Installation Manual Table of Contents Page Introduction... 2 Important Safety Information...3, 4 Installation Overview... 4, 5, 6 Single Sided/Single Unit... 7 Double

More information

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

MantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before

More information

Assembly Instructions Above Worksurface Riser Shelf Systems and Back / End Stops

Assembly Instructions Above Worksurface Riser Shelf Systems and Back / End Stops Assembly Instructions Above Riser Shelf Systems and Back / End Stops Back Stops and End Stops Adjustable Riser Shelves Instrument Riser Shelves Stationary Riser Shelves IMPORTANT PLEASE READ THESE INSTRUCTIONS

More information

Installing the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools

Installing the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools Installing the Profile Privacy Panel Complete these instructions to install the Profile Privacy Panel. Privacy panels are available in various heights to match tiers and include mounting hardware for slat

More information

STYLE BAR & TONNEAU COVER INSTALLATION

STYLE BAR & TONNEAU COVER INSTALLATION STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT

More information

C-Series & S-Series Classic Frame with Transom (Single or Pair)

C-Series & S-Series Classic Frame with Transom (Single or Pair) 1. TOOLS REQUIRED Tape measure 6' magnetic level 3' magnetic level Safety Glasses Screw gun #2 Screwdriver tip #3 Screwdriver tip Philips Head screwdriver (Used to move frame on wall using oval slots on

More information

FlexFrame - Storage Components and Skins

FlexFrame - Storage Components and Skins FlexFrame - Storage Components and Skins 1/4 Square Drive Ball-Point Hex-Bit Socket 1/8 Short Hex, 1-1/2 Overall Length McMaster Part # 54075A44 Table of Contents Topic Page Storage Components 2 General

More information

Installation Instructions

Installation Instructions Installation Instructions Follow these simple instructions to install your OneDayCab! IMPORTANT: Unpack and check shipment for damage. Verify color, size and parts before demolition. Installation of interiors

More information

Technical Environment Systems INSTALLATION MANUAL

Technical Environment Systems INSTALLATION MANUAL Technical Environment Systems INSTALLATION MANUAL Technical Environment Systems INSTALLATION MANUAL Table of Contents INTRODUCTION Full Frame, Open Frame & Upright Assembly...A Foundations...B Mobile &

More information

Preference Collection 5580 Treatment Console INSTALLATION GUIDE

Preference Collection 5580 Treatment Console INSTALLATION GUIDE Preference Collection 5580 Treatment Console INSTALLATION GUIDE 0 WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious injury

More information

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)

GlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only) List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.

More information

HOMECREST STYLE SLING 3J300 Installation Instructions

HOMECREST STYLE SLING 3J300 Installation Instructions 1 HOMECREST STYLE SLING 3J300 Installation Instructions Before beginning, take careful note of how the chaise is assembled, particularly the adjustment hardware. An additional set of hands to help during

More information

AIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS

AIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS AIR MASTER SYSTEMS INSTALLATION GUIDE TABLE OF CONTENTS GENERAL INFORMATION...1 Freight Damage... 1 Repairing Paint Scratches...1 BASE CABINETS... 2 Drawer Removal and Reinstallation...2 Replacing Drawer

More information

STOP. V00029AC Rev. 04 READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID TOOL LIST. NET-ACCESS S-Type Network Cabinets

STOP. V00029AC Rev. 04 READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID TOOL LIST. NET-ACCESS S-Type Network Cabinets Rev. 04 STOP READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID NET-ACCESS S-Type Network Cabinets -Phillips screwdriver -Flatblade screwdriver -22mm socket wrench -15mm socket wrench

More information

ASSEMBLY INSTRUCTIONS RIGHT & LEFT HAND "J" TABLE

ASSEMBLY INSTRUCTIONS RIGHT & LEFT HAND J TABLE ASSEMBLY INSTRUCTIONS RIGHT & LEFT HAND "J" TABLE (1) COMPONENT LIST FOR RIGHT & LEFT HAND "J" TABLE NOTE: Please count and inspect all pieces before disposing of any carton or packing materials. 24" x

More information

Compass. Installation Guide. Beta Draft. Wright Line LLC

Compass. Installation Guide. Beta Draft. Wright Line LLC Compass Installation Guide Beta Draft Wright Line LLC World Headquarters 160 Gold Star Boulevard Worcester, MA 01606 Tel: 800-225-7348 508-852-4300 Fax: 508-365-6178 www.wrightline.com info@wrightline.com

More information

** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at:

** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 3/01/2007 VISIT THE LITIME WEB SITE: WWW.LITIME.COM ** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 1 (800) 225-3865 Double Shed Doors for Back

More information

LOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page

LOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit

More information

ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here.

ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here. ROS-APT Caucus Plinth Table with Trough Note: Details apply, however the actual configuration of your table may vary from what is depicted here. Parts List - Tables Tops, Top Insert Panels and Base panels

More information

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM The only table saw fence with Automatic Positioning Control TM OWNER S MANUAL Please read this owner s manual before use and keep it at hand for reference. Note: The INCRA TS II system consists of three

More information

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION

READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully

More information

Installation Instructions

Installation Instructions edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung

More information

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM

OWNER S MANUAL CONTENTS. The only table saw fence with Automatic Positioning Control TM The only table saw fence with Automatic Positioning Control TM OWNER S MANUAL Please read this owner s manual before use and keep it at hand for reference. Note: The INCRA TS III system consists of three

More information

Kai Installation Instructions

Kai Installation Instructions Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;

More information

Sliding Glass Door Assembly and Installation Guide

Sliding Glass Door Assembly and Installation Guide Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all

More information

FitWork Walkstation Series 7 AdjusTables

FitWork Walkstation Series 7 AdjusTables FitWork Walkstation Tools Required: #2 Phillips Bit with Extension Page 1 of 20 A7TG660606H A7TR663232H FitWork Walkstation 4mm Hex Head Bit A7TG660632H A7TR383030H www.details-worktools.com A7TG663206H

More information

Installation Instructions

Installation Instructions by Plato Woodwork Installation Instructions Plato Woodwork, Inc. 200 Third Street SW P.O. Box 98 Plato, MN 55370 www.platowoodwork.com 800.328.5924 SECTION GUIDE GETTING STARTED PAGE # Installation Methods...

More information

TechBench Installation Manual

TechBench Installation Manual Manual Table of Contents TechBench Overview....2 Bench Assembly Linear,36 (914,4mm) Wide 96 (2438,4mm) Wide 3,4,5,6,7 Bench Assembly Linear,24 (609,6mm) Wide 30 (762mm) Wide..8,9 Bench Assembly Corner

More information

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/

https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED

More information

LCD LIFT Flat Panel Display System Installation Manual. Table of Contents

LCD LIFT Flat Panel Display System Installation Manual. Table of Contents LCD LIFT Flat Panel Display System Installation Manual Table of Contents Page Installation Overview... 2 Trim Ring Installation... 3 LCD Lift Installation....4 Actuator Switch Installation.5 Top Plate

More information

Mirage Installation Manual

Mirage Installation Manual Mirage Installation Manual General Information This installation manual provides necessary information for the safe installation of the Mirage product. WARNING: Failure to follow the instructions in this

More information

INSTALLATION GUIDE FOR METAL LABORATORY CASEWORK

INSTALLATION GUIDE FOR METAL LABORATORY CASEWORK LABORATORY Casework & Cabinets INSTALLATION GUIDE FOR METAL LABORATORY CASEWORK RDM Industrial Products, Inc. RDM LAB CABINET INSTALLATION GUIDE TABLE OF CONTENTS GENERAL INFORMATION...1 Freight Damage...1

More information

LAN Locker Adjustable Shelves

LAN Locker Adjustable Shelves Adjustable Shelves LAN LOCKER ADJUSTABLE SHELVES * Adjustable Shelves are available for LAN LOCKER widths: 24, 30, 48, 60, and 72. * When installing more than one Adjustable Shelf, it is recommended that

More information

Arlink 8000 Workstation

Arlink 8000 Workstation Arlink 8000 Workstation Instructions for Assembly Introduction Basic Frame Assembly Worksurface Assembly Drawer and Power Beam Assembly Light Fixture and Shelves Worksurface Grounding Instructions Wrist

More information

Series 7 - Adjustable Height Tables

Series 7 - Adjustable Height Tables Page 1 of 22 Series 7 - Adjustable Height Tables Installation Instructions Tools required: #2 Phillips Bit with Extension #2 Square Drive Bit 4mm Hex Drive Bit Series 7 - Adjustable Height Tables Installation

More information

Pickup Box Utility Rack Package Installation (Instruction ID: )

Pickup Box Utility Rack Package Installation (Instruction ID: ) 017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation

More information

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED

RAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL

More information

F l a t S c r e e n A R M S I n s t a l l a t i o n

F l a t S c r e e n A R M S I n s t a l l a t i o n ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)

More information

Transit Connect Full/Half Installation Instructions

Transit Connect Full/Half Installation Instructions GATHER THESE TOOLS FOR ASSEMBLY & INSTALLATION 7/16 wrench, T45 Torx socket, 7/16 socket, 3/8 drive ratchet - 3/8 socket One 1/8 square end driver bit provided - Electric drill/driver/18v cordless One

More information

6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT

6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT 1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS MINI REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS

More information

Before Assembling the Storage Wall

Before Assembling the Storage Wall Chapter 1 Assembling the Lista Storage Wall Lista provides two types of standard Storage Walls: B251 and B255. The design, construction, assembly, and quality are identical for both types, however, B251

More information

Installation And Care Instructions. Vertical Honeycomb Shades

Installation And Care Instructions. Vertical Honeycomb Shades Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...

More information

Closet System Installation Manual

Closet System Installation Manual Closet System Manual Thank you For choosing our Custom Closet Collection to fit all your needs Closets come fully assembled to make your project an enjoyable and satisfying experience. With quality Custom

More information

INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER

INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER INS T A L L A TIO N INS T R U C TIO N S HORSESHOE W/ BAR HANGER 6-1/2" 5" 2-7/16" 3-7/16" Ø2-7/8" 4-7/8" 11" 2" 3/16" 1/2" HORSESHOE W/ BAR S P ECIFICATIONS PARTS AND TOOLS Tools Needed Tape Measure Pencil

More information

Preference Collection and Treatment Console INSTALLATION GUIDE

Preference Collection and Treatment Console INSTALLATION GUIDE Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious

More information