WASHING MACHINE AND WASHER-DRIER
|
|
- Vivien Green
- 6 years ago
- Views:
Transcription
1 GB /
2 Index 1 CONFORMITY OF APPLIANCE 3 2 DIMENSIONS OF WASHING MACHINE/WASHER-DRIER AND HOUSING SPACE 3 3 UNPACKING 4 4 LEVELLING 5 5 FITTING THE FRONT PANEL AND INSERTING THE MACHINE INTO THE UNITS Fitting accessories for wooden panel (door) Fitting the elements to the front of the machine Using the drilling template Fitting the elements on the wooden panel (door) Fitting the panel on the machine Fitting the machine into the units 10 6 PLUMBING IN Connecting to the water supply Connecting the drainage pipe 12 7 CONNECTION TO THE MAINS 13 CAUTIONS AND ADVICE 13 N.B. All measurements are expressed in millimetres (mm). GB /
3 Merloni Elettrodomestici 1 CONFORMITY OF APPLIANCE This appliance complies with the following EC Directives: 73/23/EEC dated 19/02/73 (Low voltages) and subsequent amendments 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent amendments 2 DIMENSIONS OF WASHING MACHINE/WASHER-DRIER AND HOUSING SPACE Fig min 570 min The housing space, as well as having the dimensions indicated in Fig. 1, must obviously allow the electric cable and the water supply and drainage pipes to pass. GB /
4 3 UNPACKING Fig. 2 After removing the packing, ensure that the appliance is undamaged. The inside of the washing machine/washer-drier comprises a swinging unit, which is locked during transport using three screws at the rear of the machine, as shown in Fig. 2. GB /
5 4 LEVELLING Fig. 3 To ensure that the washing machine/washer-drier operates properly, it must be set level. To level the machine, turn the adjusting feet as illustrated in Fig. 3. The angle of inclination measured on the worktop must not exceed 2 degrees. When fitting on carpeting, ensure that ventilation is not blocked at floor level. GB /
6 5 FITTING THE FRONT PANEL AND INSERTING THE MACHINE INTO THE UNITS Should it be necessary to transport the machine to its final destination after having fitted the wooden panel, we recommend that the original packing be used; for this reason the packing has been designed to allow the wooden panel to be fitted to the machine without having to unpack the product completely, as can be seen from Fig. 4. Fig. 4 (continues) lavabiancheria washing machine machine laver waschmaschine Lato porta Door side Cote porte Tur seite A B C D GB /
7 Fig. 4 (continued) lavabiancheria washing machine machine laver waschmaschine Lato porta Door side Cote porte Tur seite E F 5.1 Fitting accessories for wooden panel (door) The accessories provided to fit the wooden panel are shown in the following figures. Fig. 5 Fig. 6 N 2 Hinge supports N 2 Hinges GB /
8 Fig. 7 Fig. 8 N 1 Magnet N 1 Magnet striker Fig. 9 Fig. 10 N 1 Rubber block N 2 Mopboard guide The following accessories are also provided n 6 Self-tapping screws l = 13 mm type A n 2 Self-tapping screws l = 9 mm type F n 2 Metric flathead screws l = 25 mm type B to fasten the magnet striker to the unit n 4 Metric screws l = 15 mm type C to fasten the hinge supports to the unit n 4 Metric screws l = 7 mm type D to fasten the hinges to the supports GB /
9 5.2 Fitting the elements to the front of the machine Fit the hinge supports to the surface, positioning the hole indicated by an arrow in Fig. 5 towards the inside of the surface, and using screws of type C. Fit the magnet striker on the opposite side at the top, using the two screws of type B. 5.3 Using the drilling template Bring the top edge of the drilling template up to the top edge of the panel, ensure that it is correctly positioned and centred both vertically and horizontally, referring to the lines drawn at the ends, and mark the positions of the four holes on the wooden panel. Using a milling cutter of suitable size, cut the four housings for the two hinges, the rubber block and the magnet. 5.4 Fitting the elements on the wooden panel (door) Insert the hinges into the housings prepared (the mobile part of the hinge must be towards the outside of the panel) and fasten them using four screws of type A. Insert the magnet into the top housing on the opposite side from the hinges, and fasten it using two screws of type B. Insert the rubber block into the housing at the bottom. The panel is now ready to be fitted on the machine. 5.5 Fitting the panel on the machine Insert the prong of the hinge indicated by an arrow in Fig. 6 into the housing on the hinge support, press the panel towards the surface of the machine and fasten the two hinges using two screws of type D. GB /
10 5.6 Fitting the machine into the units Fig. 11 Push the appliance into the opening, aligning it with the other units. Turn the adjusting feet to bring the machine up to the required height. To adjust the position of the wooden panel vertically and horizontally, turn screws C and D illustrated in Fig. 11. Fig. 12 If the machine is fitted at one end of the modular kitchen, fit one or both the mopboard guides as shown in Fig mm Using the screws type F, adjust the depth according to the position of the mopboard, and if necessary fix it to the guides. GB /
11 6 PLUMBING IN 6.1 Connecting to the water supply Ensure that the water pressure is within the minimum and maximum levels indicated in the rating plate, located at the rear of the washing machine/washer-drier. Connect the supply pipe to a cold water tap with a _ threaded mouth, taking care to fasten it tightly to the tap and inserting the filter element A carefully (Fig. 13). If the water supply pipe is new, or has not been used for some time, run the water through it before connecting, until the water runs clear and contains no impurities. If this precaution is not taken, the water inlet may become clogged, damaging the machine. Connect the other end of the pipe to the machine at the water connector provided, top right hand side (Fig. 14). Fig. 13 Fig. 14 A GB /
12 6.2 Connecting the drainage pipe Fig. 15 The drainage pipe can be connected as follows: 1. To the sink drain siphon, ensuring that the drainage pipe is fastened to the worktop to prevent water from returning to the Washer-drier; 2. To a drainage pipe with a minimum diameter of 40 mm; 3. Resting it on the sink, using the special plastic U-bend provided to prevent crushing or excessive curving of the pipe (Fig. 15). The special plastic U-bend must be firmly fixed to the wall to prevent the drainage pipe from moving and draining water anywhere but into the sink. In all cases, the free end of the pipe must measure between 40 and 100 mm and it must not be underwater. A GB /
13 Fig. 16 It is important that the pipe be positioned at a height of above 60 cm; otherwise the pipe must be fastened to the hook provided at the top of the back section, as illustrated in Fig CONNECTION TO THE MAINS Insert the plug into a power socket fitted with a proper earthing connection, after first checking that the voltage and frequency of the mains power supply correspond to the values indicated on the rating plate on the machine's stainless steel door fairing, and that the system to which it is being connected is sized for the maximum load indicated on the plate. If the socket to which the machine is connected does not correspond to the plug, always replace it with a suitable plug, rather than using adapters or extensions, as these might result in overheating and therefore create a fire hazard. CAUTIONS AND ADVICE 1. Do not use drainage pipes with extensions over three metres in length, as these might reduce the efficiency of the appliance. If required, the spare parts code is and the pipe is 3 metres long. Should it be necessary to use a water supply pipe longer than the one provided with the machine (with waterstop), the spare parts code is and the pipe is 3.5 m long. 2. To ensure that the machine operates correctly it must be properly levelled, so that its inclination does not exceed 2â on the top. To do this, turn the adjusting feet (Chapter 4). GB /
14 Merloni Elettrodomestici spa viale Aristide Merloni, Fabriano tel. 0732/ telex fax 0732/ GB /
Merloni Elettrodomestici. Technical Fitting Manual FRIDGE. Language Issue/Edition Page GB /
GB 99-11-03/01 1-38 Index 1 CONFORMITY OF APPLIANCE 3 2 MAIN ASSEMBLY TYPES 3 2.1 Under worktop 3 2.2 Double door 10 2.3 Combined 14 2.4 Single door Fridge or single door Freezer 19 2.5 Combined free-standing
More informationNRS Installation Manual
NRS Installation Manual Chair Mount Type Standard / EU Spec. KAZE (AY-KFPLU AY-NRS1 is shown.) OTO (AY-OLL AY-NRS1 is shown.) Separate Type (AY-NRS2B-W is shown.) Installer: Read through this installation
More informationMounting a BalanceBox 400 to a brick wall
Unpack the BalanceBox 400 and remove the Wall frame cover and its bag of screws. Slide the cover out at the top. NOTE: the cover is NOT included with the BalanceBox 400H LOCK SCREW HOLE MOBILE STAND MOUNTING
More informationAIR ACTIVATED MODULAR INLET
AIR ACTIVATED MODULAR INLET 345678903456789034567890 345678903456789034567890 MI4 345678903456789034567890 345678903456789034567890 Each MI4 includes: - Modular Inlet - Counterweight - Hardware Package
More information13MM FLAT WRENCH FOR LEVELING THE GLIDES OF STRUCTURE 6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME
1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS ALTERNATIVE
More informationTOYOTA MOTOR EUROPE CA Products Division Tel : Fax :
TOYOTA MOTOR EUROPE CA Products Division Tel : + 32 2 745 26 77 Fax : + 33 2 745 26 99 Ordering part numbers Comments Part Numbers Wooden floor one hatch PZ449-D3C42-11 one hatch with carpet PZ449-D3C42-01
More informationNEPAL Installation procedure
PART DESCRIPTION 1.- Door handle (1pc) 2.- Long tight bar (1pc) 3.- Short tight bar (1pc) 4.- Support block-lower (2pcs) 5.- Wall jamb cap (2pcs) 6.- Tight bar support (2 pcs) 7.- Acrilic base (1pc) 8.-
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationFig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7
FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track
More informationKawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions.
Owner s Manual Model: Kawasaki Teryx 750 Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationMighty Mo GX Series Cabinet Installation Guide. OR Rev /11
Mighty Mo GX Series Cabinet Installation Guide OR-71601787 Safety and Warning ATTENTION The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
More informationC PART LIST HARDWARE LIST. Kitchen Cart IMPORTANT NOTE
88 9200 006C Kitchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken
More informationXL-GC03 Sliding Door Lock Installation Manual PAT XL-GC06 Sliding Door Hanger Installation Manual XL-GC08 Sliding Door Lock Guide Installation Manual
XL-GC0 Sliding Door Lock Installation Manual PAT XL-GC0 Sliding Door Hanger Installation Manual XL-GC0 Sliding Door Lock Guide Installation Manual Read all instructions carefully before installation. Before
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationCopyright Black Box Corporation. All rights reserved Park Drive Lawrence, PA Fax
Copyright 2003. Black Box Corporation. All rights reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 JULY 2003 RM3010A RM315-R2 RM323-R2 RM329 RM451 RM457 RM3020A RM316 RM324-R2
More informationinstallation instructions
installation instructions Easi-Plan WC Frame 820mm with Dual Flush Cistern ref: EPWC-05-1005 Easi-Plan WC Frame 980mm with Dual Flush Cistern ref: EPWC-05-1505 EASI-PLAN installation instructions Parts
More informationInstallation Instructions Student 101 Fume Cupboard
Installation Instructions Student 101 Fume Cupboard Refer drawing on next page 0. If your fume cupboard is supplied with a flatpack bench frame, see step1. If your fume cupboard will be mounted on an existing
More informationALLORA SWING PANEL INSTALLATION INSTRUCTIONS
ALLORA SWING PANEL INSTALLATION INSTRUCTIONS Before Installation Please check that your Allora Swing Panel is undamaged SEQUENCE OF INSTALLATION These instructions are also available from the Athena website:
More informationPrepare Base Assembly. (If pump is pre-assembled on base, go to step#8.)
F L Instructions Maxim 3000 Turbo Flush Installation INTRODUCTION Satellite portable restrooms and accessories must be assembled according to approved assembly procedures. Avoid variations in assembly
More informationHousehold Appliances. Over-the-Range Microwave. Installation Instructions. For Models: HMV9302, HMV9305, HMV9306, HMV9307
Over-the-Range Microwave Household Appliances Installation Instructions For Models: HMV9302, HMV9305, HMV9306, HMV9307 PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING IMPORTANT: Save these instructions
More informationPop-Out Slim Video Wall Mount
Installation Guide ADM-VWSP Pop-Out Slim Video Wall Mount CONTENTS Installation Safety Notes Page 2 Interface Adaptors Page 3 Installation Instructions Page 4 Installation Options Page 9 Alternative Mounting
More informationGE Monogram. Installation. Instructions. Microwave Oven. Under Cabinet Installation. and. JX827 Series Built-In Kit. Models.
GE Monogram Installation Instructions Under Cabinet Installation and JX827 Series Built-In Kit Models ZEM200 Series CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationInstallation Instructions
Installation Instructions Ceiling Mount Bracket for DLP Based Projectors (for High Ceilings) Model No. ET-PKD100H Contents Important Safety Notice.................. 2 For DLP Based Projector: PT-D10000
More informationaluminium profile system
aluminium profile system 63 AME System aluminium profiles overview series profiles introduction 80x80 x80 x80/180 x Aluminium profiles are provided with longitudinal grooves which can be used in conjunction
More informationDisplay Shelving Installation Instructions
Display Shelving Installation Instructions Top Rail (R-T) Back (BE) (R-C) Splicer Rail (R-S) 78 H to 120 H only Uprite (U) Uprite End Trim (UET) Shelf Back (BE) Base End Trim (BET) (R-C) 96 H to 120 H
More informationProHead. User s Guide
ProHead User s Guide 2Profoto ProHead Profoto ProHead Thank you for choosing Profoto. Thanks for showing us your confidence by investing in a ProHead unit. For more than four decades we have sought the
More informationGENERAL OPERATIONAL PRECAUTIONS WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following.
More informationBY ALIEN TECHNOLOGIES CORP
BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More informationOperating Manual. for CUTTING, PERFORATING, BENDING SLB120
Operating Manual for CUTTING, PERFORATING, BENDING SLB120 31040\B06eng 0896 0 Contents 1. Scope of delivery... 1 2. Technical specifications... 1 3. Applications... 1 4. Commissioning... 2 5. Cutting...
More informationUser guide ProHead Plus
User guide ProHead Plus For other languages visit: /support ProHead Plus 2 Congratulations on your new Profoto product! Thanks for showing us your confidence by investing in a ProHead unit. For more than
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationASSEMBLY INSTRUCTIONS JK270
TOOLS REQUIRED: One knife to open packaging Two ½ wrench or socket (metric 13) One 9/16 wrench or socket (metric 14) One #2 Philips (+) screwdriver NOTE: All bolts are 9/16 (metric 14) and nuts are ½ (metric
More informationInstallation Instructions. Oakmont Folding Doors
Before You Start For quick and easy installation of your Oakmont folding door, read these instructions thoroughly. A few minutes of prior planning will make the job easier and ensure years of trouble-free
More information6MM ALLEN KEY FOR ROOF CLIPS PHILLIPS HEAD BIT FOR SCREWS FOR DOOR FRAME SPIRIT/LASER LEVEL TO LEVEL THE UNIT
1 TOOLS REQUIRED: MOVING CART/DOLLY FOR TRANSPORTING PANELS, ROOF, AND POSTS TWO 9 FT. STEP LADDERS FOR INSTALLING ROOF & PANELS MINI REVERSIBLE RATCHET 1/4 DRIVE FOR CORNER SCREWS ON TOP TRAVERSE BEAMS
More informationKiosk Solution W1000. Installation and Assembly Instructions July 2015 Edition
Kiosk Solution W1000 Installation and Assembly Instructions July 2015 Edition All product names mentioned in this document are the trademarks, brands or registered trademarks of their respective owner.
More informationASSEMBLY INSTRUCTIONS FOR "GA" MODULAR BUILDINGS ALL MODELS
ASSEMBLY INSTRUCTIONS FOR "GA" MODULAR BUILDINGS ALL MODELS W01 CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety sake, please read
More informationAssembly instructions for cable termination frame (2-5 bays)
Assembly instructions for cable termination frame 60131 (2-5 bays) 1.General The cable termination frames are concepted for erection in dry indoor rooms. They serve for the insulated accommodation of:
More informationINSTALLATION GUIDE MICROWAVE OVEN UPMC3084ST. MFL _00
INSTALLATION GUIDE MICROWAVE OVEN UPMC3084ST MFL06208710_00 www.thesignaturekitchen.com YOUR SAFETY FIRST BEFORE YOU START Proper installation is the installer's responsibility! Proper installation by
More informationInstalling flat panels on the MPL15 wall mount
Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape
More informationSeries 1500 Aluminum Door Canopy
Series 500 Aluminum Door Canopy with Sidewings It is our recommendation that you read instructions carefully prior to assembly and installation. Series 500 with Sidewings mounting bar (A) top trim (B)
More informationLCD LIFT Flat Panel Display System Installation Manual. Table of Contents
LCD LIFT Flat Panel Display System Installation Manual Table of Contents Page Installation Overview... 2 Trim Ring Installation... 3 LCD Lift Installation....4 Actuator Switch Installation.5 Top Plate
More informationINSTALLING YOUR NEW SPRING LIFT ARM KIT
INSTALLING YOUR NEW SPRING LIFT ARM KIT 1. Measure the distance that the roof is to be raised. [If your lift system is completely non-functional, you will need to calculate or estimate this distance as
More informationUniversal Adaptor Kit
TigerRip Fence Universal Adaptor Kit Guide Version 2.30 À Á Ã Ä Å Â Æ Ç An illustrated replacement parts list with order numbers is found on the last page of this guide. Illustrated Accessory Parts List
More informationPROFILE Flat Panel Console System Installation Manual
PROFILE Flat Panel Console System Installation Manual Table of Contents Page Introduction... 2 Important Safety Information...3, 4 Installation Overview... 4, 5, 6 Single Sided/Single Unit... 7 Double
More informationinstallation instructions WC Frame 1180mm with Dual Flush Cistern
installation instructions WC Frame 1180mm with Dual Flush Cistern (C,D,E) K F/G N L M 12 13 14 16 1 2 11 A 5 6 Q O Y 3 C 10 E D B P,Z,AA R T V S 4 U 2 No. Part no. Description Quantity A WC Frame with
More informationVYTEX PREMIUM SLIDING GLASS DOOR. Table of Contents. Precautions and Safety 2. Tools Required...3. Inspect and Prepare Door...4
VYTEX PREMIUM SLIDING GLASS DOOR Table of Contents Precautions and Safety 2 Tools Required...3 Inspect and Prepare Door...4 Hardware and Parts Check List....4 Master Frame Assembly 5 Master Frame Installation..7
More informationAssembly Instructions Nevins Phone Booth
Assembly Instructions Nevins Phone Booth Included Hardware Tools Required supplied by installer Drill & Bit Bolt A - (16) 1/4-20 x 1-1/2 hex head Bolt B - (20) 1/4-20 x 2-1/2 phillips head Screw 1 - (24)
More informationA Generic Sauna Room Assembly Manual
A Generic Sauna Room Assembly Manual Parts List Exterior 1. Ceiling Assembly 2. Wall Elements 3. Exterior Mouldings 4. Top Exterior Mouldings 5. Bottom Exterior Mouldings 6. Main Base Frame 7. ABS Bolt
More informationOVER THE RANGE MICROWAVE OVEN INSTALLATION INSTRUCTIONS
OVER THE RANGE MICROWAVE OVEN INSTALLATION INSTRUCTIONS Please read and save these installation instructions. MODEL NO.: DOTR12CWIV/DOTR12CBIV P/N: 3828W5U0202 YOUR SAFETY FIRST Read this entire manual
More informationOperating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher
Operating, Servicing, and Safety Manual Model # 100 Standard Hydraulic Tubing Notcher Model #100-U Heavy Duty Hydraulic Tubing Notcher Model # 100 Standard Model #100-U Heavy Duty CAUTION: Read and Understand
More informationPWM-T210 Installation Instructions UNIVERSAL FLAT PANEL MOUNT
UNIVERSAL FLAT PANEL MOUNT IN-PWMT210.R0 TABLE OF CONTENTS Warning Statements 3 Parts List 4 Installation Tools 4 Locating the Center of the 5 Mounting Bracket Positioning 5 Securing the Mounting Brackets
More informationINSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE
INSTALLATION INSTRUCTIONS DANUBE ACRYLIC NEO ANGLE March 2013 DOOR 2 Page 1 of 5 INSTALLATION INSTRUCTIONS NEO ANGLE 6MM FRAMELESS AND 4MM FRAMED SHOWER DOOR DANUBE, DELTA, SIGNATURE, OCEANIA, CASCADE
More informationPlease read these instructions before use and keep for future reference
Wardrobe Assembly Guide Allen Key Provided (if required) Philips Screwdriver Required Hammer Required Please read these instructions before use and keep for future reference Caution! Two Person Assembly
More informationKitchen Fittings Hanging Cabinets and Accessories
Cabinet hanger Knock-in version, load bearing capacity 130 kg/pair Depth adjustment Finish: Galvanized Concealed mounting of cabinet hanger behind the rear panel (Min. 16 mm free space required) Mounting
More informationFREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS 27694B
FREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS 27694B 1 TOOLS REQUIRED: CLAW HAMMER KNIFE 1/2 WRENCH OR SOCKET 1. USE KNIFE TO REMOVE ALL PLASTIC STRAPS FROM AROUND PALLET AND CARTON. STRAP 2. USE CLAW HAMMER
More informationShorePort PWC Lift Instructions " x 138" Sandstone ShorePort " x 138" White ShorePort " x 138" Tan ShorePort
ShorePort PWC Lift Instructions 00-8" x 8" Sandstone ShorePort 009-8" x 8" White ShorePort 090-8" x 8" Tan ShorePort....... - PUT SAFETY FIRST To avoid the risk of personal injury or death, study and fully
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationHYDRO-TOWER INSTALLATION INSTRUCTIONS
HYDRO-TOWER 300 300 INSTALLATION INSTRUCTIONS IN-WALL TANK K-4179T/K-4178T/K-10611T K-4177T/K-8857T/K-20341T/K-75890T/K-75891T BEFORE YOU BEGIN Read installation guide in illustration and word file carefully,
More informationGlass Front Sauna Room Assembly Manual
Glass Front Sauna Room Assembly Manual Classic Bench Version: 1.3 Note: Above images are for illustrative reference only and may differ from actual item. Parts List Exterior *For room with full glass wall
More informationFitted Furniture Installation and Aftercare Guide
Fitted Furniture Installation and Aftercare Guide Customer Service Contact Number 08008 778899 Important Information In the unlikely event that your product is damaged or faulty in any way, this must be
More informationPreference Collection and Treatment Console INSTALLATION GUIDE
Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious
More informationThe Cambridge Raised Planter Extension Kit
ASSEMBLY INSTRUCTIONS The Cambridge Raised Planter Extension Kit www.newenglandarbors.com www.newenglandarbors.co.uk in (0 cm) 8 in ( cm). in (90 cm). in (8 cm). in (8 cm) 8. in ( cm) 9 in ( cm) Please
More informationINTRODUCTION Tools Required Laminate Washroom Products... 4 DUCT PANELS Fixing the Frame: Fixing the Shadow Panels...
Contents INTRODUCTION... 2 Tools Required... 3 Laminate Washroom Products... 4 DUCT PANELS... 4 Fixing the Frame:... 5 Fixing the Shadow Panels... 9 Fitting the Duct Panels:... 10 WASHSTATIONS... 15 Fixing
More informationTECHNICAL MANUAL - CONSTRUCTION AND INSTALLATION
ERGON T.E. LIVING SLIM TECHNICAL MANUAL - CONSTRUCTION AND INSTALLATION Swinging-sliding door with connecting rod on frame JAMB THICKNESS 30/40 mm CELEGON S.r.l. - Via G. Galilei, 6-30035 Mirano (Venezia)
More informationRangerWare Fiberglass Door System Installation Instructions P/N
Page 1 of 9 RangerWare Fiberglass Door System Installation Instructions P/N 2878016 ORDER OF INSTALLATION Note: To assure proper order, read all Accessory Installation Instructions before beginning. 1.
More informationAluminium hinges DORMA LM. October 1999
Aluminium hinges DORMA LM October 1999 DORMA LM Engineered down to the smallest detail adaptable to any profile system The DORMA LM series of aluminium hinges has been developed to give fast, safe and
More informationFlat Panel Stand FPZ-655. for 32" to 55" Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold
FPZ-655 Flat Panel Stand for 32" to 55" Flat Panel Screens For a viewing experience that really stands out, Peerless FPZ-655 Universal Flat Panel Stand for 32" 55" flat panel TVs provides a brilliant combination
More informationSenior Swing. Caution
*740132* 740132 2800 Overhead Concealed Series 9500 Surface Applied Series Senior Swing Installation Instructions Caution LCN Senior Swing The Senior Swing Power Operator System is a low energy product
More informationEASY STOW/HIDEAWAY LOFT LADDER
EASY STOW/HIDEAWAY LOFT LADDER TWIST CATCH ASSEMBLY A4 A3 A2 A1 A7 A6 A5 A Installation and Operating Instructions Read Carefully Before Installation Please check you have all components listed (tick Boxes)
More informationImportant Loading Information. Tools Required. Meridian Lateral Files Instructions
Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationKitchen Installation Manual
Kitchen Installation Manual June 2018 www.howdens.com 2 www.howdens.com Section pages Introduction... page 4 Supplied products... page 4 Guide - Hints and tips... page 5 Cabinet installation fittings...
More informationAllora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED
Allora ALCOVE ENCLOSURE INSTALLATION BEFORE INSTALLATION CHECK THAT YOUR ALLORA SHOWER ENCLOSURE SYSTEM IS UNDAMAGED ALCOVE SHOWER Your shower can be installed to open Left hand or Right hand by rotating
More informationSteele TV Stand Stock # BH
LOT NUMBER: DATE PURCHASED: / / Steele TV Stand Stock # BH46-084-899-02 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More information#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,
More informationB235 Mobius Sconce Page 1 of 6
Mobius Sconce 28-9450 Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS PRODUCT PROPERLY MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. We recommend installation by a qualified individual trained in the
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More informationTitan Series Awning Assembly and Installation Instructions
Titan Series Awning Assembly and Installation Instructions Be sure to use safety glasses when assembling and installing the awning. Some metal parts may have sharp edges. Use work gloves to handle them.
More informationBioPrism Solid Surface
Please read all instructions before installing products. These instructions are intended for use with InPro s standard toilet partitions, which include 58 high doors and wall panels, when deviating from
More informationPortofino Installation Guide
vjul16 (for 17 or 24 mm Surface Wall Profiles) DO NOT ASSEMBLE WITHOUT FULLY READING THESE INSTRUCTIONS Page 2 Thank you for purchasing this Portofino shower enclosure. Please study these instructions
More informationChambersScribers V.2. Owner s Manual. Parts List. 10b. 10c. ChambersScriber V.2 Owner s Manual, July Robert W. Chambers.
8 10 12 ChambersScribers V.2 10b 4 1 Owner s Manual 14 Parts List 11 3 2 1- ErgoGrip 2- Straight bubble vials 3- Bullseye bubble vial 4- Receiver - Female slide - Sliders (qty 2) - Thumbscrew to lock Slider
More informationSTOP. Performance Plus 2.0 Series. hazard! ATTENTION: Is your cabinet damaged?
Performance Plus. Series Warning: Excessive Warning: Excessive weight hazard! weight hazard! Use two or more people to move, assemble, or install cabinets and locker to avoid back injury. Do not leave
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes
More informationWall mounting bracket
Install Manual Wall mounting bracket Please read this manual carefully before operating your set and retain it for future reference. OSW200 P/NO : MFL63640578 (1502-REV01) www.lg.com COMPONENT Install
More informationWaist-high Railing System from Tempered Glass BH-06 ASSEMBLY AND OPERATION MANUAL
Waist-high Railing System from Tempered Glass BH-06 ASSEMBLY AND OPERATION MANUAL Waist-high Railing System from Tempered Glass BH-06 Assembly & Operation Manual Assembly & Operation Manual Dear Customers!
More informationMALEKO WALL-MOUNT FAUCET INSTALLATION
SKU(s): 934146 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the
More informationINSTRUCTION SHEET U19
U19 All Refrigerator and All Freezer Trim Kit Installation Product Line: U19 All Refrigerator and All Freezer Models Parts Included in Kit TRIMKITEZ1 (Part# 297333500): Single Trim Kit Components Single
More informationTapping Screw (W/Flange) 46 Cord Armor 47 Tube (D) 48 Cord. 45 Cord Clip. Tapping Screw (W/Flange) 10 Gear Cover Ass'y. 12 Socket (B) Ass'y
W8VB The exploded assembly drawing should be used only for authoized service center. W8VB Item No. Part time 1 Magnetic Hex. Socket 2 Sub Stopper 3 O-Ring (S-16) 4 Locator (A) 5 Lock Sleeve (A) 6 O-Ring
More informationCOWO. Customer Wall Outlet. 1 General. 2 Kit content. 3 Handling of the box. TC-1203-IP Rev A, Apr
COWO I N S T A L L A T I O N I N S T R U C T I O N TC-1203-IP Rev A, Apr 2017 www.commscope.com Customer Wall Outlet 1 General Customer Wall Outlet 2 Fiber for max. 2 bend reduced fibers, 2 SC-adapters
More informationOrganisational Kitchen Fittings Kitchen Cabinet Accessories
Kitchen waste bin systems Single waste bin, capacity 1 litres Carcase width: Min. 400 mm For door mounting: For left and right hand use Installation: Screw fixing to side panel Housing: Steel, plastic
More informationET-PKL100S. Installation Instructions. Ceiling Mount Bracket (for Low Ceilings) Model No.
Installation Instructions Ceiling Mount Bracket (for Low Ceilings) Model No. ET-PKL100S Thank you for purchasing this Panasonic Product. JJ To customers The Installation Instructions is intended for use
More informationSHELTON THERMOSTATIC SHOWER PANEL
SKU(s): 413241 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the plumbing, floor,
More informationVanity Installation Instructions
Vanity Installation Instructions Segments of these instructions will relate to your vanity. Please read these instructions thoroughly and ensure the appropriate instructions are used during the installation
More informationPEDESTAL INSTALLATION. Guidelines for installing adjustable height pedestals
BASIC REQUIREMENTS Irrespective of the type of pavers or tiles that will be installed over pedestals, the following basic requirement must be met. Decks must be designed not to exceed the load capacity
More informationGE Monogram. Installation. Instructions. 36" Vent Hood. Model ZV750. Call anywhere in the US and Canada -
at :: rangehoods. com GE Monogram Instructions Model ZV750 GE Monogram at:: rangehoods. com is a division of CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:
More informationExtra Wide Designer Lockers Series Installation Instructions
Extra Wide Designer Lockers 20000 Series Thank you for selecting the 20000 Series Extra Wide Designer Lockers. We are confident that the quality and construction of the lockers will prove to be a good
More information