Tex-452-A, Rotational Capacity Testing of Fasteners Using a Tension Measuring Device

Size: px
Start display at page:

Download "Tex-452-A, Rotational Capacity Testing of Fasteners Using a Tension Measuring Device"

Transcription

1 Using a Tension Measuring Device Contents: Section 1 Overview...2 Section 2 Definitions...3 Section 3 Apparatus...4 Section 4 Part I, Rotational Capacity Testing...5 Section 5 Part II, Values for Fasteners with ASTM A 490 Bolts...8 Section 6 Identification...9 Texas Department of Transportation 1 TxDOT 08/1999

2 Section 1 Overview Section 1 Overview This method covers the procedure for performing rotational capacity testing of fasteners with ASTM A 325 and A 490. The values shown in the tables of 'Part I, Rotational Capacity Testing' apply to fastener assemblies with ASTM A 325 bolts. The values shown in the tables of 'Part II, Values for Fasteners with ASTM 490 Bolts' address fasteners with ASTM A 490 bolts. Units of Measurement The values given in parentheses (if provided) are not standard and may not be exact mathematical conversions. Use each system of units separately. Combining values from the two systems may result in nonconformance with the standard. Texas Department of Transportation 2 TxDOT 08/1999

3 Section 2 Definitions Section 2 Definitions The following terms and definitions are referenced in this test method: Bolt length - Bolt length is the distance from the end of the threaded shank to the underside of the bolt head. (See 'Bolt Diagram') Grip length - Grip length is the region between the bearing face of a nut and the bolt head. (See 'Bolt Diagram') Long bolts - Long bolts are bolts that will fit in a direct tension indicator with the required "stick-out." Short bolts - Short bolts are bolts that are too short to be assembled in a direct tension indicator. These bolts may be tested in a steel plate, web, or flange, which contains a hole of the required diameter. Figure 1. Bolt Diagram. Texas Department of Transportation 3 TxDOT 08/1999

4 Section 3 Apparatus Section 3 Apparatus The following apparatus is required: Torque wrench, calibrated, capable of measuring the torque values listed in Step 6 of the 'Rotational Capacity of Long Bolts' procedure Tension measuring device (i.e. Skidmore-Wilhelm or equivalent), calibrated, of size required for bolts to be tested Spacers and/or washers, with hole sizes no larger than 1.6 mm (1/16 in.) greater than bolt to be tested Steel section, on which to mount the bolt calibrator. Flange of girder or cross frame accessible from the ground is satisfactory Steel section, with hole to install bolt. See the 'Rotational Capacity of Short Bolts' procedure for requirements Spud wrench, or equivalent. Texas Department of Transportation 4 TxDOT 08/1999

5 Section 4 Part I, Rotational Capacity Testing Section 4 Part I, Rotational Capacity Testing This part describes the procedure for performing rotational capacity testing of fasteners. The values shown in the tables apply to fastener assemblies with ASTM A 325 bolts. Procedure Long Bolts The following table describes steps used in rotational capacity testing of long bolts. Rotational Capacity of Long Bolts Step Action 1 Attach the tension-measuring device to a convenient steel section. 2 Measure and record the bolt length (see 'Bolt Diagram'). 3 Thread the nut on the bolt, and measure and record the stick out of the bolt when 3 to 5 full threads of the bolt are located within the grip length (see 'Bolt Diagram' ). 4 Mark off a vertical line, plus lines at 1/3 of a turn (120 ) and 2/3 of a turn (240 ), measured in a clockwise direction, from vertical on the face plate of the tension measuring device. 5 Install the bolt into the tension-measuring device. Include the required number of shim plates and/or washers (always use at least one washer under the nut) to produce the stick out measured in Step 3. 6 Using a spud wrench or equivalent, tighten the bolt to the snug tension listed below and to within a tolerance of -0, +9 kn ( -0, +2 kips). Snug tension will be indicated on the tension indicator. (Refer to 'Table 1, Values for Fasteners with ASTM A 490 Bolts' table.) U. S. BOLTS (A 325) Bolt 1/2 5/8 3/4 7/ /8 1-1/4 1-3/8 1-1/2 (In.) Snug Tension (kips) S. I. BOLTS (A 325) Bolt (mm) Snug Tension (kn) Match mark the nut at the vertical line marked in Step 4 on the faceplate of the tensionmeasuring device. 8 Using the calibrated manual torque wrench, tighten the bolt to at least the tension listed below. Record the torque required to reach the tension and the value of the corresponding bolt tension. Torque must be measured with the nut in motion. (Refer to 'Table 2, Values for Fasteners with ASTM A 490 Bolts' table.) U. S. BOLTS (A 325) Bolt 1/2 5/8 3/4 7/ /8 1-1/4 1-3/8 1-1/2 (in.) Tension (kips) S. I. BOLTS (A 325) Bolt Texas Department of Transportation 5 TxDOT 08/1999

6 Section 4 Part I, Rotational Capacity Testing Rotational Capacity of Long Bolts Step Action (mm) Tension (kn) Further tighten the bolt to the rotation listed below. The rotation is measured from the initial marking in Step 7. Record the bolt tension after achieving this rotation. Assemblies which fail prior to this rotation either by stripping of the threads or fracture of the bolt fail the test. 10 The bolt tension measured in Step 9, after the required rotation, must equal or exceed the values in the table shown below. Assemblies which do not meet this tension have failed the test. (Refer to the 'Table 3, Values of Fasteners with ASTM A 490 Bolts' table.) Bolt Length (measured in Step 2) Required Rotation (turns) 4 x Bolt or Less Greater than 4 but no more than 8 x Bolt 2/ /3 Greater than 8 x Bolt U. S. BOLTS (A 325) Bolt 1/2 5/8 3/4 7/ /8 1-1/4 1-3/8 1-1/2 (in.) Tension (kips) S. I. BOLTS (A 325) Bolt (mm) Tension (kn) Loosen and remove the nut; examine the threads on the nut and bolt. No signs of thread shear failure, stripping, or torsional failure of the bolt should be evident. Assemblies that have evidence of stripping have failed the test. (Elongation of the bolt, in the threads between the nut and bolt head, is to be expected at the required rotation and is not to be classified as a failure). 12 Calculate and record the torque value as shown under 'Calculations.' Short Bolts The following table describes the steps used in rotational capacity testing of short bolts: Rotational Capacity of Short Bolts Step Action 1 Measure and record the bolt length (see 'Bolt Diagram' ). Install the nut on the bolt and measure the stick out of the bolt when 3 to 5 full threads of the bolt are located within the grip length (see 'Bolt Diagram'). 2 Mark a vertical line and lines 1/3 of a turn (120 ), 1/2 turn (180 ), and 2/3 of a turn (240 ), measured in a clockwise direction, from vertical on the plane of the plate, web, or flange. 3 Install bolt into hole of steel plate, web, or flange with required number of shim plates and/or washers (at least one washer under nut must always be used) to produce thread stick out in Step 1. 4 Snug the bolt using a spud wrench. Snug condition should be the normal effort applied to a 305 mm (12 in.) long wrench. The applied torque should not exceed 20% of the torque shown in Step 6. Match mark the nut at the vertical line marked in Step 2 on the plate, web, or flange. 5 Tighten the bolt by turning the nut using the torque wrench to the rotation listed below. A second wrench must be used to prevent rotation of the bolt head during tightening. Record the torque required to reach this rotation. The torque must be measured with the nut in motion. Texas Department of Transportation 6 TxDOT 08/1999

7 Section 4 Part I, Rotational Capacity Testing Bolt Length (measured in Step 1) 4 x Bolt or Less Greater than 4 but no more than 8 x Bolt Greater than 8 x Bolt Required Rotation (turns) 1/3 1/2 2/3 6 The measured torque should not exceed the values listed below. Assemblies that exceed the listed torques have failed the test. (Refer to 'Table 4, Values for Fasteners with ASTM A 490 Bolts' table.) U.S. BOLTS (A 325) Bolt (in.) 1/2 5/8 3/4 7/ /8 1-1/4 1-3/8 1-1/2 Torque (ft.-lbs) S. I. BOLTS (A 325) Bolt (mm) Torque(N-m) Tighten the bolt further to the rotation required below. The rotation is measured from the initial marking in Step 4. Assemblies, which fail prior to this rotation either by stripping of the threads or fracture of the bolt, fail the test. Bolt Length (measured in Step 1) Required Rotation (turns) 4 x Bolt or Less Greater than 4 but not more than 8 x Bolt 2/ /3 Greater than 8 x Bolt 8 Loosen and remove the nut; examine the threads on the nut and bolt. No signs of thread shear failure, stripping, or torsional failure of the bolt should be evident. Assemblies that have evidence of stripping have failed the test. (Elongation of the bolt, in the threads between the nut and the bolt head, is to be expected at the required rotation and is not to be classified as a failure.) Calculation The following calculation determines the torque value: Torque 025. P D Where: Torque = torque, N-M (ft.-lbs.) measured with the calibrated torque wrench and recorded in Step 8. P = measured bolt tension, in N (lbs.) from the direct tension indicator and recorded in Step 8. D = bolt diameter, in m (ft.) (diameter in m = mm/1000; diameter in feet = diameter in inches/12). The torque measured and recorded in Step 8 must be equal to or less than this calculated value. Assemblies with torque values exceeding this calculated value fail the test. Texas Department of Transportation 7 TxDOT 08/1999

8 Section 5 Part II, Values for Fasteners with ASTM A 490 Bolts Section 5 Part II, Values for Fasteners with ASTM A 490 Bolts This part covers values to use when performing rotational capacity testing of fasteners with ASTM A 490 bolts. Table 1 (Refer to Step 6 of 'Rotational Capacity of Long Bolts' procedure) Table 1, Values for Fasteners with ASTM A 490 Bolts U. S. BOLTS (A 490) Bolt (in.) 1/2 5/8 3/4 7/ /8 1-1/4 1-3/8 1-1/2 Snug Tension (kips) S. I. BOLTS (A 490) Bolt (mm) Tension (kn) Table 2 (refer to Step 8 of the 'Rotational Capacity of Long Bolts' procedure) Table 2, Values for Fasteners with ASTM A 490 Bolts U.S. BOLTS (A 490) Bolt (in.) 1/2 5/8 3/4 7/ /8 1-1/4 1-3/8 1-1/2 Tenison (kips) S.I. BOLTS (A 490) Bolt (mm) Tension (kn) Table 3 (refer to Step 10 of the Rotational Capacity of Long Bolts' procedure) Table 3, Values for Fasteners with ASTM A 490 Bolts U. S. BOLTS (A 490) Bolt (in.) 1/2 5/8 3/4 7/ /8 1-1/4 1-3/8 1-1/2 Tension (kips) S. I. BOLTS (A490) Bolt (mm) Tension (kn) Table 4 (refer to Step 6 of the 'Rotational Capacity of Short Bolts' procedure) Table 4, Values for Fasteners with ASTM A 490 Bolts U. S. BOLTS (A 490) Bolt (in.) 1/2 5/8 3/4 7/ /8 1-1/4 1-3/8 1-1/2 Torque (Ft.-Lbs.) S. I. BOLTS (A 490) Bolt (mm) Torque (N-M) Texas Department of Transportation 8 TxDOT 08/1999

9 Section 6 Identification Section 6 Identification A rotational-capacity lot number should be assigned to each combination of fastener assemblies tested. Texas Department of Transportation 9 TxDOT 08/1999

Procedure for Wrench Calibration and Snug Tightening

Procedure for Wrench Calibration and Snug Tightening Procedure for Wrench Calibration and Snug Tightening 1. Scope: This procedure provides the method for calibration of a manual torque wrench or an adjustable impact wrench and the snug tightening procedure

More information

Copyright. Michael Joseph Gilroy. May 1997

Copyright. Michael Joseph Gilroy. May 1997 Copyright by Michael Joseph Gilroy May 1997 Tightening of High Strength Metric Bolts by Michael Joseph Gilroy, B.S. Thesis Presented to the Faculty of the Graduate School of The University of Texas at

More information

Procedure for Testing Direct Tension Indicators (DTI) Assemblies

Procedure for Testing Direct Tension Indicators (DTI) Assemblies Procedure for Testing Direct Tension Indicators (DTI) Assemblies 1. Scope: This test is to ensure that the bolt will be at or above the specified minimum bolt tension after installation when the direct

More information

Contents. Grade 2, 5, 8 Hex Bolts 4. Heavy Hex Head Structural Bolts 6. A325 and A490 Tension Control Bolts (TC) 13. Nuts 22.

Contents. Grade 2, 5, 8 Hex Bolts 4. Heavy Hex Head Structural Bolts 6. A325 and A490 Tension Control Bolts (TC) 13. Nuts 22. Who we are Amcan Jumax is the result of a merging between Boulons Jumax and Amcan Threaded Products, two successful companies well established, both with excellent reputations. The new entity is a bigger

More information

Tightening of Structural Joints

Tightening of Structural Joints The design, fabrication, assembly and inspection of steel structures using metric high strength structural bolts and nuts to AS 1252 are covered in AS 4100 - SAA Steel Structures Code which should be referred

More information

Structural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the grade A325 structural bolt.

Structural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the grade A325 structural bolt. Structural Bolting ASTM F3125/F3125M is a structural bolt specification covering inch and metric bolt grades. This specification contains 4 inch series bolting grades: A325, F1852, A490, and F2280. These

More information

ERECTION & CONSTRUCTION

ERECTION & CONSTRUCTION ERECTION & CONSTRUCTION High Strength Structural Bolting Author: Clark Hyland Affiliation: Steel Construction New Zealand Inc. Date: 24 th August 2007 Ref.: Key Words High Strength Bolts; Property Class

More information

LOAD INDICATOR WASHERS USING DTI S WITH TENSION CONTROL BOLTS

LOAD INDICATOR WASHERS USING DTI S WITH TENSION CONTROL BOLTS Studying the use of DTI s in conjunction with Tension Control Bolts and the ramifications associated with this practice. The use of Direct Tension Indicator Washers with Tension Control Bolts has been

More information

USER MANUAL MODEL MZ-100 BOLT TENSION CALIBRATOR

USER MANUAL MODEL MZ-100 BOLT TENSION CALIBRATOR USER MANUAL MODEL MZ-100 BOLT TENSION CALIBRATOR 442 SOUTH GREEN ROAD SOUTH EUCLID, OHIO 44121 USA VOICE: 216-481-4774 FAX: 216-481-2427 www.skidmore-wilhelm.com TABLE OF CONTENTS Introduction... 2 Typical

More information

Evaluation of In-Pavement Light Fixture Designs and Performance

Evaluation of In-Pavement Light Fixture Designs and Performance Evaluation of In-Pavement Light Fixture Designs and Performance Presented to: IES ALC Fall Technology Meeting By: Joseph Breen Date: Background In-Pavement Light Fixture Assemblies Utilize a Circle of

More information

ODOT ITB Group 4 Item 33 Qty. 1

ODOT ITB Group 4 Item 33 Qty. 1 ODOT ITB 180-17 Group 4 Item 33 Qty. 1 ODOT ITB 180-17 Group 4 Item 34 Qty. 1 ODOT ITB 180-17 Group 4 Item 35 Qty. 1 ODOT ITB 180-17 Group 4 Item 36 Qty. 1 STRUCTURAL BOLTS NUCOR FASTENER TECHNICAL

More information

Mechanical joints. Major diameter Mean diameter Minor diameter Pitch p chamfer. Root Crest. Thread angle 2a. Dr. Salah Gasim Ahmed YIC 1

Mechanical joints. Major diameter Mean diameter Minor diameter Pitch p chamfer. Root Crest. Thread angle 2a. Dr. Salah Gasim Ahmed YIC 1 Screw fasteners Helical threads screws are an extremely important mechanical invention. It is the basis of power screws (which change angular motion to linear motion) and threaded fasteners such as bolts,

More information

NTTC Tank Truck Week Awareness Gaskets/Fasteners/Flanges

NTTC Tank Truck Week Awareness Gaskets/Fasteners/Flanges NTTC Tank Truck Week 2015 Awareness Gaskets/Fasteners/Flanges OVERVIEW 1. Flange 101 Flange Types Inspection & Assembly 2. Gaskets 101 Stress Tightness 3. Fastener 101 Yield Lubrication Bolted Flanged

More information

SECTION 3. BOLTS. bolt is a standard AN-type or a special-purpose bolt, and sometimes include the manufacturer.

SECTION 3. BOLTS. bolt is a standard AN-type or a special-purpose bolt, and sometimes include the manufacturer. 9/8/98 AC 43.13-1B SECTION 3. BOLTS 7-34. GENERAL. Hardware is the term used to describe the various types of fasteners and small items used to assemble and repair aircraft structures and components. Only

More information

Assembly procedure for KA_S series January, 04, 2010

Assembly procedure for KA_S series January, 04, 2010 Assembly procedure for KA_S series January, 04, 2010 The following procedure is valid for KA060S and KA080S. However, only pictures of KA060S are shown as examples. The other is similar. 1. Examine specification

More information

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS

C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS C4 Fabrication Rock Slider Installation 14+ 5th Gen 4Runner w/o KDSS Thank you for your purchase of the C4 Fabrication s 5th Gen 4Runner Rock Sliders! This product was carefully crafted to ensure a perfect

More information

UNIVERSITY OF THESSALY

UNIVERSITY OF THESSALY UNIVERSITY OF THESSALY MECHANICAL ENGINEERING DEPARTMENT Instructor: Dr. S.D. Chouliara e-mail: schoul@uth.gr MACHINE ELEMENTS Task 2 1. Let the bolt in the following Figure be made from cold-drawn steel.

More information

SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS

SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS UDC 621.882.211 [669.14.018.291] IS : 3757-1985 (Reaffirmed 2003) Edition 3.2 (1989-07) Indian Standard SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS ( Second Revision ) (Incorporating Amendment Nos.

More information

USER MANUAL Nord-Lock X-series washers

USER MANUAL Nord-Lock X-series washers USER MANUAL Nord-Lock X-series washers JOINT GUIDE 3 ASSEMBLY INSTRUCTIONS 4 TECHNICAL DATA 5 TORQUE GUIDE 5 THE EXCEPTIONAL SYSTEM THAT PREVENTS BOLT LOOSENING AND SLACKENING Nord-Lock X-series washers

More information

Removing the Z-Axis lead screw

Removing the Z-Axis lead screw Page 1 of 8 TITLE: Sabre Z-Axis Lead Screw Replacement Procedure Gerber FastFact #: 5048 Supplied by: Gerber Hardware Support Last Modified: June 14, 2007 Summary: Tools used: The following procedure explains

More information

Installation Instructions TMW Antenna Tower Mount for 4ft (1.2m) Antennas.

Installation Instructions TMW Antenna Tower Mount for 4ft (1.2m) Antennas. Description The following pages show the steps required to assembly and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation

More information

AN, MS, NAS Bolts. AN3 20 bolts are identified by a multi-part code:

AN, MS, NAS Bolts. AN3 20 bolts are identified by a multi-part code: AN, MS, NAS Bolts Most bolts used in aircraft structures are either (a) general-purpose, (b) internal-wrenching or (c) close-tolerance AN, NAS, or MS bolts. Design specifications are available in MIL-HDBK-5,

More information

Bolted Joint Types Grip Washer

Bolted Joint Types Grip Washer Structural Bolting The Research Council on Structural Connections (RCSC) prepares specifications and documents related to structural connections RCSC s Specification for Structural Joints Using ASTM A325

More information

Umbrella Inserts and Stubby Screens

Umbrella Inserts and Stubby Screens ADHESIVE ANCHORING SPECIALISTS Umbrella Inserts and Stubby Screens High Performance Adhesive Systems for Fastening to Hollow Base Materials DESCRIPTION/ADVANTAGES Hollow Block Fastening with A7 Adhesive

More information

Fasteners. Fastener. Chapter 18

Fasteners. Fastener. Chapter 18 Fasteners Chapter 18 Material taken from Mott, 2003, Machine Elements in Mechanical Design Fastener A fastener is any device used to connect or join two or more components. The most common are threaded

More information

A training course delivered at a company s facility by Matrix Engineering, an approved provider of Bolt Science Training

A training course delivered at a company s facility by Matrix Engineering, an approved provider of Bolt Science Training A training course delivered at a company s facility by Matrix Engineering, an approved provider of Bolt Science Training Following is an outline of the material covered in the training course. Each person

More information

Instruction Manual for installing

Instruction Manual for installing Instruction Manual for installing Preloaded (HSFG) Bolting with TurnaSure DIRECT TENSION INDICATORS CE Marked EN 14399-9 TurnaSure LLC TABLE OF CONTENTS Introduction... 1 Theory of Preloaded Bolting Assemblies...

More information

Instruction Manual for installing

Instruction Manual for installing Instruction Manual for installing Preloaded (HSFG) Bolting with TurnaSure DIRECT TENSION INDICATORS TurnaSure LLC TABLE OF CONTENTS Introduction... 1 Theory of Preloaded Bolting Assemblies... 2 Tightening

More information

712 - STRUCTURAL STEEL CONSTRUCTION SECTION 712 STRUCTURAL STEEL CONSTRUCTION

712 - STRUCTURAL STEEL CONSTRUCTION SECTION 712 STRUCTURAL STEEL CONSTRUCTION SECTION 712 STRUCTURAL STEEL CONSTRUCTION 712.1 DESCRIPTION Fabricate and erect the structural steel as designated in the Contract Documents. See SECTION 705 for fabrication of structural steel. Provide

More information

Independent Containment System (ICS)

Independent Containment System (ICS) Installing the Independent Containment System (ICS) Complete these instructions to install the Independent Containment System (ICS). Prerequisites This installation requires a team of at least two people.

More information

Threaded Fasteners 2. Shigley s Mechanical Engineering Design

Threaded Fasteners 2. Shigley s Mechanical Engineering Design Threaded Fasteners 2 Bolted Joint Stiffnesses During bolt preload bolt is stretched members in grip are compressed When external load P is applied Bolt stretches further Members in grip uncompress some

More information

Swivel Hoist Ring Page 142

Swivel Hoist Ring Page 142 Swivel Hoist Ring Page 142 Hoist Rings Color coded to distinguish between UNC (Red) and Metric (Silver) thread types HR-125 M HR-125 Available in UNC and Metric thread sizes. UNC threads available in sizes

More information

Big Block Installation Manual For Systems without A/C

Big Block Installation Manual For Systems without A/C Big Block Installation Manual For Systems without A/C Billet Specialties, Inc. 500 Shawmut Ave. La Grange, IL 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 Hardware List For Chevrolet Big Block Tru

More information

6o ft (18.3 m) Southwest Windpower, Inc West Route 66 Flagstaff, Arizona USA Phone: Fax:

6o ft (18.3 m) Southwest Windpower, Inc West Route 66 Flagstaff, Arizona USA Phone: Fax: 6o ft (18.3 m) sectional MONOPOLE TOWER INSTALLATION MANUAL Southwest Windpower, Inc. 1801 West Route 66 Flagstaff, Arizona 86001 USA Phone: 928.779.9463 Fax: 928.779.1485 www.skystreamenergy.com 3-CMLT-1390-01

More information

COMMON WRENCHES INTRODUCTION

COMMON WRENCHES INTRODUCTION COMMON WRENCHES INTRODUCTION A wrench is a hand tool used to provide grip and mechanical advantage in applying torque to turn objects usually nuts and bolts. Wrenches allow us to use less force to rotate

More information

METRIC FASTENERS 1520 METRIC FASTENERS

METRIC FASTENERS 1520 METRIC FASTENERS 1520 METRIC FASTENERS METRIC FASTENERS A number of American National Standards covering metric bolts, screws, nuts, and washers have been established in cooperation with the Department of Defense in such

More information

Installation Instructions

Installation Instructions CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order

More information

TITAN2-EDGE Public Access Computer Station Dual Track

TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the

More information

TWL 1500 TORQUE WRENCH LOADER

TWL 1500 TORQUE WRENCH LOADER TWL 1500 TORQUE WRENCH LOADER OPERATOR S HANDBOOK (PART NUMBER 60246.1) CONTENTS PAGE 1 OF 8 INTRODUCTION 2 SPECIFICATION 3 ITEMS SUPPLIED 3 AVAILABLE OPTIONS 3 ASSEMBLY INSTRUCTIONS A. ASSEMBLY OF TRANSDUCER

More information

High Strength Weathering Steel Structural Bolting Assemblies PC 8.8 Hex. Cooper & Turner Ltd. Worldclass products for a.

High Strength Weathering Steel Structural Bolting Assemblies PC 8.8 Hex. Cooper & Turner Ltd. Worldclass products for a. Cooper & Turner Ltd Worldclass products for a worldwide market 2015 Cooper & Turner Ltd Sheffield Road Sheffield, S9 1RS South Yorkshire England United Kingdom T: +44 (0) 114 256 0057 E: sales@cooperadnturner.co.uk

More information

Two basic types of single

Two basic types of single Designing with Single Plate Connections M. Thomas Ferrell M. Thomas Ferrell is president of Ferrell Engineering, Inc., of Birmingham, AL. He is a member of the AISC Committee on Manuals and Textbooks,

More information

Cyclic tests of engineered shear walls with different bottom plate and anchor bolt washer sizes (Phase II)

Cyclic tests of engineered shear walls with different bottom plate and anchor bolt washer sizes (Phase II) Cyclic tests of engineered shear walls with different bottom plate and anchor bolt washer sizes (Phase II) Prepared by Rakesh Gupta, Associate Professor Heather Redler, Graduate Research Assistant Milo

More information

RBP-1215B-RX DODGE RAM QUAD CAB RX3

RBP-1215B-RX DODGE RAM QUAD CAB RX3 RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side

More information

Assembly, Use and Care Instructions

Assembly, Use and Care Instructions Assembly, Use and Care Instructions Product #336677 Instruction #1068318 Rev. F Thank you for purchasing a Caldwell Lead Sled DFT 2. The Lead Sled DFT 2 comes to you partially assembled. It will require

More information

DTI s. Direct Tension Indicators. Hardened Steel Washers. Leading provider of bolt loading & removal solutions

DTI s. Direct Tension Indicators. Hardened Steel Washers. Leading provider of bolt loading & removal solutions Direct Tension Indicators Stationary Nuts Gap Gap Hardened Steel Washers Before Tensioning After Tensioning Patented bolt load measuring technology Eliminates fugitive emissions Verifies correct tension

More information

Pickup Box Utility Rack Package Installation (Instruction ID: )

Pickup Box Utility Rack Package Installation (Instruction ID: ) 017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation

More information

Square Shear Beam Mounting Guidelines

Square Shear Beam Mounting Guidelines Issue Date: January 2016 Please Retain for Future Reference 2016-01-11 Square Shear Beam Mounting Guidelines Subject: Square Shear Beam Recommendations Introduction: Even though Digi-Star load cells are

More information

AN, MS, NAS Bolts. AN3 20 bolts are identified by a multi-part code:

AN, MS, NAS Bolts. AN3 20 bolts are identified by a multi-part code: AN, MS, NAS Bolts Most bolts used in aircraft structures are either (a) general-purpose, (b) internal-wrenching or (c) close-tolerance AN, NAS, or MS bolts. Design specifications are available in MIL-HDBK-5,

More information

1/2/2016. Lecture Slides. Screws, Fasteners, and the Design of Nonpermanent Joints. Reasons for Non-permanent Fasteners

1/2/2016. Lecture Slides. Screws, Fasteners, and the Design of Nonpermanent Joints. Reasons for Non-permanent Fasteners Lecture Slides Screws, Fasteners, and the Design of Nonpermanent Joints Reasons for Non-permanent Fasteners Field assembly Disassembly Maintenance Adjustment 1 Introduction There are two distinct uses

More information

Umbrella Inserts and Stubby Screens

Umbrella Inserts and Stubby Screens ADHESIVE ANCHORING SPECIALISTS Umbrella Inserts and High Performance Adhesive Systems for Fastening to Hollow Base Materials DESCRIPTION/ADVANTAGES Hollow Block Fastening with A7+ Adhesive Umbrella Inserts

More information

Standard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm)

Standard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm) 495 R Billerica Ave. N. Billerica, MA 01862 USA Tel: (978) 459-8800 Fax: (978) 459-3310 / 8814 www.radiowavesinc.com email: sales@radiowavesinc.com Standard Pole Mount Parabolic Antenna Mounting Instructions

More information

Bulk Storage Rack Assembly Instructions

Bulk Storage Rack Assembly Instructions Bulk Storage Rack Assembly Instructions Upright Frame Assembly Determine which end of the post goes up. The keystone slots on the front face of the post are wider at the top than at the bottom (see diagram

More information

Installation Instructions Kit, Base Rail Bracket Part # 31413

Installation Instructions Kit, Base Rail Bracket Part # 31413 Installation Instructions Kit, Base Rail Bracket Part # 31413 Dealer / Installer: Provide a copy of these Instructions to the end user of this product. These Instructions provide important operating and

More information

Replacing the build plate clamps

Replacing the build plate clamps Repair manual Replacing the build plate clamps Instructions The build plate clamps hold the glass plate in place on the heated bed. There are two fixed in place at the back of the heated bed and two at

More information

installation guide 1 GUIDE#: pwb-wwtowv1-pol-003

installation guide 1 GUIDE#: pwb-wwtowv1-pol-003 g300 WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This WakeWorks wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the

More information

Bolted Joint Design. Mechanical Properties of Steel Fasteners in Service

Bolted Joint Design. Mechanical Properties of Steel Fasteners in Service Bolted Joint Design There is no one fastener material that is right for every environment. Selecting the right fastener material from the vast array of those available can be a daunting task. Careful consideration

More information

Real Life Ninja Complete Starter Pack (14ft. Warped Wall) Assembly Instructions

Real Life Ninja Complete Starter Pack (14ft. Warped Wall) Assembly Instructions MATERIALS: 3 - Main Sections (Only 2 Sections for 10 ) 8 3 deck screws for joining sections inside of 2 Rock Wall Panels (with pre-installed t-nuts. Top panel comes with ladder mounting block preinstalled.)

More information

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16 R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged

More information

BOLTCALC Program. problems. User Guide. Software for the Analysis of Bolted Joints

BOLTCALC Program. problems. User Guide. Software for the Analysis of Bolted Joints User Guide BOLTCALC Program Software for the Analysis of Bolted Joints problems BOLTCALC is produced by Bolt Science Limited Bolt Science provides analytical solutions to bolting problems www.boltscience.com

More information

SECTION 1050 STEEL BRIDGE SUPERSTRUCTURE

SECTION 1050 STEEL BRIDGE SUPERSTRUCTURE 1050.1 1050.3(b) SECTION 1050 STEEL BRIDGE SUPERSTRUCTURE 1050.1 DESCRIPTION This work is the construction of a steel bridge superstructure. 1050.2 MATERIAL (a) Deck and Barriers. Cement Concrete Structures

More information

A training course delivered at a company s facility by Matrix Engineering, an approved provider of Bolt Science Training

A training course delivered at a company s facility by Matrix Engineering, an approved provider of Bolt Science Training A training course delivered at a company s facility by Matrix Engineering, an approved provider of Bolt Science Training Following is an outline of the material covered in the training course. Each person

More information

Installation Instructions

Installation Instructions FORD 20K Industry Standard Rail Custom Mounting Kit #2760 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine

More information

Swivel Hoist Ring RIGGING ACCESSORIES. Color coded to distinguish between UNC (Red) and Metric (Silver) thread types.

Swivel Hoist Ring RIGGING ACCESSORIES. Color coded to distinguish between UNC (Red) and Metric (Silver) thread types. RIGGING ACCESSORIES Color coded to distinguish between UNC (Red) and Metric (Silver) thread types. Available in UNC and Metric thread sizes. UNC threads available in sizes from 800 pounds to 100,000 pounds,

More information

ISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition

ISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E) ISO 2005 PDF disclaimer This

More information

Lab Style Table Frame Part No Assembly Guide Automation Technology

Lab Style Table Frame Part No Assembly Guide Automation Technology Ergonomic Workstations Lab Style Table Frame Part No. 8 0 Assembly Guide 7 90 70 Automation Technology SPECIFICATIONS Lab style frame part number... 80 Height... 70 mm (8.") Width... 90 mm (.7") Depth...

More information

Additional Information

Additional Information NUMBER: 1 34 13 S.M. REF.: Listed in Table ENGINE: EPA04/07 Series 60 DATE: January 2013 SUBJECT: CHECKING CYLINDER LINER PROTRUSION ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL FASTENER AND HARDWARE GENERAL REQUIREMENTS 1. DESCRIPTION This section contains general requirements for common hardware installation. Covered are selection and installation of cotter pins, installation

More information

Note: Conditions where bending loads are imposed on the bolt e.g. non-parallel bolting surfaces, should be avoided.

Note: Conditions where bending loads are imposed on the bolt e.g. non-parallel bolting surfaces, should be avoided. Bolted Joint Design Introduction A most important factor is machine design, and structural design is the rigid fastening together of different components. This should include the following considerations..

More information

1. ANSI/ASME Standard B , Square and Hex Bolts and Screws, Inch Series

1. ANSI/ASME Standard B , Square and Hex Bolts and Screws, Inch Series SECTION 31 66 13 HELICAL PILES AND HELICAL ANCHORS PART 1 - GENERAL 1.1 DESCRIPTION A. This work pertains to furnishing and installing Helical Piles and Bracket Assemblies shown in the Contract in accordance

More information

Installation Instructions

Installation Instructions CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order

More information

Installation Instructions

Installation Instructions FORD 20K Industry Standard Rail Custom Mounting Kit #2738 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine

More information

INSTALLATION INSTRUCTION RRU DOUBLE LIGHT POLE MOUNT

INSTALLATION INSTRUCTION RRU DOUBLE LIGHT POLE MOUNT INSTALLATION INSTRUCTION RRU Double Light Pole Mount for installation of two RRU units on mast, towers or other vertical structures. CUE DEE YOUR INNOVATIVE PARTNER 1 CONTENTS 1. PRODUCT COVERED IN THIS

More information

Bolts and Set Screws Are they interchangeable?

Bolts and Set Screws Are they interchangeable? 1903191HA Bolts and Set Screws Are they interchangeable? Prof. Saman Fernando Centre for Sustainable Infrastructure SUT Introduction: This technical note discusses the definitions, standards and variations

More information

Kai Installation Instructions

Kai Installation Instructions Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;

More information

Bolt Material Types and Grades 1- Bolts made of carbon steel and alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 Nuts made of carbon steel and alloy

Bolt Material Types and Grades 1- Bolts made of carbon steel and alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 Nuts made of carbon steel and alloy Bolt Material Types and Grades 1- Bolts made of carbon steel and alloy steel: 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 10.9 Nuts made of carbon steel and alloy steel: 4, 5, 6, 8, 10, 12 2- Bolts made of stainless

More information

ISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition

ISO INTERNATIONAL STANDARD. Fasteners Torque/clamp force testing. Éléments de fixation Essais couple/tension. First edition Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 16047 First edition 2005-02-01 Fasteners Torque/clamp force testing Éléments de fixation Essais couple/tension Reference number ISO 16047:2005(E)

More information

LCD/Plasma Mount Manual

LCD/Plasma Mount Manual LCD/Plasma Mount Manual Product Overview: Thank you for your Cheetah Mount purchase. All Cheetah Mounts are designed to provide excellent function, high quality, easy installation and stylish appearance.

More information

Grain Tank Cross Auger Trough Liner for John Deere 9400 / 9500 Combine

Grain Tank Cross Auger Trough Liner for John Deere 9400 / 9500 Combine www.polyskid.com P. O. Drawer 349, Monticello, GA. 31064 Phone: 800-542-7659, Fax: 706-468-2881 E-Mail: polytech@polyskid.com Grain Tank Cross Auger Trough Liner for John Deere 9400 / 9500 Combine FOR

More information

Figure 11 Flange Adapter and Back-Up Ring

Figure 11 Flange Adapter and Back-Up Ring Flange Adapters Standard back-up rings are Standard back-up rings are convoluted ductile iron with AWWA C207 150 lb drilling. One edge of the back-up ring bore must be radiused or chamfered. This edge

More information

Flat Panel Stand FPZ-655. for 32" to 55" Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold

Flat Panel Stand FPZ-655. for 32 to 55 Flat Panel Screens FEATURES. Reinforced universal adapter plate for a strong hold FPZ-655 Flat Panel Stand for 32" to 55" Flat Panel Screens For a viewing experience that really stands out, Peerless FPZ-655 Universal Flat Panel Stand for 32" 55" flat panel TVs provides a brilliant combination

More information

LENGTH IDENTIFICATION

LENGTH IDENTIFICATION 58 Power-Bolt HEAVY DUTY, ELF-UNDERCUTTING LEEVE TYPE BAE MATERIAL Concrete, Block, Brick, tone IZE RANGE 1/4" x 1" to 1-1/4" x 9 MATERIAL LENGTH IDENTIFICATION The Power-Bolt anchor has a length identification

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS E-SERIES STEP BARS / 4 OVAL STEP BARS APPLICATION: 2011-2017 Jeep Grand Cherokee PART NUMBER: 23-3610, 23-3615, 21-3610, 21-3615, 23-73610 ITEM QUANTITY DESCRIPTION TOOLS NEEDED

More information

Installation Instructions

Installation Instructions CHEVY / GMC 16K Industry Standard Rail Custom Mounting Kit #2730 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order

More information

DTFACT 16 C IN PAVEMENT LIGHT FIXTURE TESTING AND ANALYSIS FINAL SUMMARY PRESENTATION

DTFACT 16 C IN PAVEMENT LIGHT FIXTURE TESTING AND ANALYSIS FINAL SUMMARY PRESENTATION DTFACT 16 C 00047 IN PAVEMENT LIGHT FIXTURE TESTING AND ANALYSIS FINAL SUMMARY PRESENTATION IESALC Fall Technology Meeting Government Contacts Subcommittee Dallas, TX October 23, 2017 Jeremy N. Downs,

More information

NX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP

NX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP 6-1/4 HANDRAIL W/ VINYL HANDGRIP TYPICAL ASSEMBLY 5 2 BUTT JOINT 12 10 9 1 8 11 6 3 7 4 BUTT JOINT COMPONENT LIST 1 LEFT RETURN 7 UPPER IMPACT ABSORBER 2 RIGHT RETURN 8 LOWER IMPACT ABSORBER 3 OUTSIDE

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Fifth Wheel Adapter Titan 999T5 W4198 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Fifth Wheel Adapter

More information

CSS Central Mount System

CSS Central Mount System CSS-20 Installation Manual CSS-20 Safety Notifications Below are the installation instructions for the CSS-20-2 Long Span Beam Mounting System. Please read these safety notifications prior to beginning

More information

INSTALLATION INSTRUCTIONS Product No. MULTI-FIT PICK-UP

INSTALLATION INSTRUCTIONS Product No. MULTI-FIT PICK-UP INSTALLATION INSTRUCTIONS Product No. You can take it with you. PLYMOUTH, MICH. MULTI-FIT PICK-UP 37034 SMALL PARTS PACKAGE 37424 WARNING: DO NOT LUBRICATE THREADS, BOLT FAILURE MAY OCCUR DUE TO OVER TIGHTENING.

More information

Fasteners. Bolts. NAPA FastTrack Counter Sales Training Fasteners Page 1. Figure 1. Typical Measurements for a Bolt or Hex Head Cap Screw

Fasteners. Bolts. NAPA FastTrack Counter Sales Training Fasteners Page 1. Figure 1. Typical Measurements for a Bolt or Hex Head Cap Screw Fasteners Many types and sizes of fasteners are used in the automotive industry. Each fastener is designed for a specific purpose and condition. One of the most commonly used type of fastener is the threaded

More information

AR15 SUPER SLIM AND ULTRA SLIM FREE FLOAT RAIL SYSTEMS

AR15 SUPER SLIM AND ULTRA SLIM FREE FLOAT RAIL SYSTEMS MUM066011803 AR15 SUPER SLIM AND ULTRA SLIM FREE FLOAT RAIL SYSTEMS Proudly Designed and Made in USA Super Lightweight, Flush Fitting, and Continuous with Flat Top AR15 Upper Receiver Features Integral

More information

Submersible Turbine Assembly Manual

Submersible Turbine Assembly Manual Submersible Turbine Assembly Manual Table of Contents Submersible Turbine Kit Assembly Page Recommended Equipment... 2 Assembly Instructions...3-9 Special Tool Schematics... 10 Symbol Key Action Safety/Caution

More information

Rayport G Eco Dealer Kit

Rayport G Eco Dealer Kit Rayport G Eco Dealer Kit Installation Guide www.aetenergy.com Supporting a Cleaner, Greener Tomorrow 1. Table of Contents 1. Table of Contents P2 2. Installer Notes P3 3. Parts List P4-7 4. Tool List P8

More information

Tex-728-I, Measurements of Dry Film Coating Thickness on Steel

Tex-728-I, Measurements of Dry Film Coating Thickness on Steel Thickness on Steel Contents: Section 1 Overview...2 Section 2 Precautions...3 Section 3 Apparatus...4 Section 4 Procedures...5 Texas Department of Transportation 1 08/99 02/08 Section 1 Overview Section

More information

Toyota 4 Runner and Lexus GX Skid Plate installation instructions.

Toyota 4 Runner and Lexus GX Skid Plate installation instructions. Toyota 4 Runner and Lexus GX Skid Plate installation instructions. NOTE: When installing the full set of skid plate start at the rear of the vehicle and work your way forward. NOTE: Torque Specs: Tighten

More information

Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub

Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub Tuf-Lite and Tuf-Lite II Fans 4000 Series Hub INSTALLATION MANUAL Hudson Tuf-Lite and Tuf-Lite II fan blades Adjustable Pitch Fan Assembly 15 thru 20 Diameter Hudson Tuf-Lite (black) fan blades are made

More information

Installation Instructions

Installation Instructions CHEVY / GMC 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2226 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note,

More information

Welded connections Welded connections are basically the same design in AISI as in AISC. Minor differences are present and outlined below.

Welded connections Welded connections are basically the same design in AISI as in AISC. Minor differences are present and outlined below. Cold-Formed Steel Design for the Student E. CONNECTIONS AND JOINTS E1 General Provisions Connections shall be designed to transmit the maximum design forces acting on the connected members. Proper regard

More information

INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110

INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small

More information

ATLANTIS RAIL HandiSwage Installation Instructions ATLANTIS RAIL Contact Information Atlantis Rail Systems November, 2013

ATLANTIS RAIL HandiSwage Installation Instructions ATLANTIS RAIL Contact Information Atlantis Rail Systems November, 2013 ATLANTIS RAIL HandiSwage Installation Instructions ATLANTIS RAIL Contact Information Atlantis Rail Systems November, 2013 Atlantis Rail s HandiSwage System is an easy to use cable railing product utilizing

More information

Tuf-Lite III Fans 3000K Series Hub

Tuf-Lite III Fans 3000K Series Hub Tuf-Lite III Fans 3000K Series Hub INSTALLATION MANUAL Adjustable Pitch Fan Assembly 11 thru 15 Diameter Hudson Tuf-Lite III fan blades Hudson Tuf-Lite III fan blades are of single piece fiberglass reinforced

More information