AUTOMOTIVE ALTERNATOR CONVERSION FOR N750G TRANSMISSION DRIVE PULLEY MODIFICATIONS

Size: px
Start display at page:

Download "AUTOMOTIVE ALTERNATOR CONVERSION FOR N750G TRANSMISSION DRIVE PULLEY MODIFICATIONS"

Transcription

1 In this section I ll describe the modifications I made to the transmission pulley. The first thing I did was to remove all the electrical cables from the engine and drop it to expose the transmission and engine pulleys. I removed the two pulleys and the coil from behind the engine pulley, cleaned off the engine pulley, and reinstalled it. I left the magnets to preserve the balance. I was thinking of having it rebalanced but to do that I would need to have a custom mandrel made and that would drive the cost way up. So for now, I ll leave it alone. I also pulled the grounds off of the batteries as a precaution I cleaned off all the residual Loctite, reinstalled the socket head cap screws using fresh Loctite, and torqued them to 20 ft-lb. My screw database showed an advised torque of 25 ft-lb and a lubricated torque of 18 ft-lb. Since the screws were wet with Loctite I compromised on 20 ft-lb. That was about all I could muster anyway as the pulley is free to rotate and difficult to hold. Juan Rivera 8 August

2 Since I can t lock these screws I torque striped them so I can look for any loosening during inspections. The next step is to machine the transmission pulley. It s critically important to mount the pulley so it is absolutely perpendicular to the tool. The fan tabs could be removed using a lathe or a mill, but it will take a mill to cleanup the mounting surfaces inside the pulley. The back side of the pulley is a machined surface so it could be placed flat on the work surface and clamped down on the inside while the tabs are milled off, then the clamps could be moved to the outside while cleaning up the mounting surfaces. If you chose to use a lathe you might need to make a special fixture to mount the pulley. In the photograph below you can see that the thickness of the sides of the sheaves vary slightly. The outer one is quite thin on my pulley (tabbed side.) The design of the alternator drive pulley is based on a maximum total width of inches and a distance from the center of the outer sheave to the machined surface of This will produce a symmetrical pulley. The alternator drive pulley design is based on the distance from the mounting surface in the center of the pulley to the outer edge. This in tern is based on that width dimension. I don t want to reduce the width of that outer edge any more than I have to, but at the same time I need to machine those tabs off and keep going until the width is no more than With my particular pulley I think I ll end up with some rough spots and some hard coat in a few areas that look especially thin. This is a purely cosmetic issue. I ll also be left with multiple fan blade mounting holes that protrude down below that plane. I may elect to fill the holes and low spots with epoxy and then paint that surface. I ll have to see how it looks once I get going. Transmission Pulley Cross Section Juan Rivera 8 August

3 Change of plans I was going to send this out to a machine shop but I ve decided that I want to do this myself. It s too delicate an operation to leave to strangers. My mill leaves a lot to be desired since it was inexpensive and made in China. I know the headstock is not exactly perpendicular to the table and there is a lot of slop in all of my adjustments, but with care I think I can overcome most of these issues. I ll start by removing the fan tabs and stop short of the final surface dimension while I reassess my progress. Here s a shot of my first pass with the mill. You can see the cross section of the tabs. The tapped hole in the upper tab stops short of the plane where I intend to stop, but the lower hole is deeper and will look ugly. Juan Rivera 8 August

4 This picture shows my temporary stopping point. To get around the deficiencies in my mill I moved the table very little and instead, remounted the pulley in 90 degree increments. That way I was always machining in more or less the same position over the table. For my final cut I locked the quill and then rotated the pulley under the mill as I described. The width of the pulley is now sitting at ±.001 across all twelve tabs which is pretty good, considering. Juan Rivera 8 August

5 You can see that I still have material that will need to be removed since the belt clearance is tight, but I ll stop here and wait until I have the drive pulleys. I m currently.062 from my target pulley width. Ideally I d like to stop removing material before the twelve tabs start to blend together. Once that starts to happen I think the surface will start to look irregular. With luck I can remove enough material to allow sufficient belt clearance and still end up with twelve individual tabs sitting slightly above the hard coat background. Juan Rivera 8 August

6 Here s a look at one of the twelve tapped holes from the lower fan tabs. They re defiantly unsightly. I ll clean them out with a reamer later. I ve already removed a lot of weight so I m worried about balance. There is a dynamic balancing shop in the area and I stopped by for a chat the other day. For each pulley they would need to make a custom mandrel. There are also limited locations to drill lightning holes now that the tabs are removed. Weight might have to be added instead. Now it s time to clean up the mounting surfaces where the alternator drive pulley will sit. I drafted the center area of the pulley from the drawings and pictures that I have and printed it out full scale on my cheap inkjet printer using AutoCAD. Modern printers are dimensionally extremely accurate since they re driven with stepping motors. I cut the drawing out and placed it as you see. Then I used the pattern to outline the areas I need to cleanup using a felt marker. Juan Rivera 8 August

7 Here s a drawing showing the areas that need cleanup. Remember to stay away from the web fillets. I made the mistake of not waiting until I had the alternator drive pulley in my hand before starting. By mounting the two pulleys together with SHCS you can see just how close you need to get to the fillets to cleanup the mounting surfaces. I d suggest the following end mill for cleaning up the mounting pads. It has a 1/16-inch radius which will reduce stress concentrations: MSC part number ( ) 1/2" diameter, 2 flute, 1" length of cut, 1/16 radius. ($37.25) Juan Rivera 8 August

8 I set my mill to a depth of.005 and locked it down 1. I won t unlock it again until I get the drive pulleys and make sure my outer radius is large enough. A CNC mill would have made this a nice clean job, but I had to do it by hand. Going around corners is not easy and you can see the edge isn t a prefect arc. The good news is that.005 seems to be enough to cleanup the surface. The less I take off here, the less I have to remove from the fan tabs. I won t know if I ve removed enough from the tabs until I get the drive pulleys, but not enough is way better than too much. NOTE: MILLING INTO THE WEB FILLETS WAS A MISTAKE. IT COULD CASUE STRESS CRACKS LEADING TO PULLEY FAILURE. STAY AWAY FROM THE FILLETS! 1 I did not use the end mill I suggested on the previous page in these pictures. I went back later with that radiused mill to clean up the cuts shown above. Juan Rivera 8 August

9 Here s the result after taking a.005 cut. You can see that there are a few areas that still have a bit of hard coat, so the.005 cut didn t go quite far enough for a completely smooth surface, but I m not sure that s really necessary. I ll have to wait until the drive pulleys arrive to finalize the depth of the pad cleanup and decide whether I took off enough of the fan tabs to allow the belt to clear properly. Altering those web fillets was a big mistake. I ll have to try to repair them by going deeper with an end mill that has a radius. I ll get to that once I have the drive pulley so I can gauge how much belt clearance I have. I ll write that up once I get started. Juan Rivera 8 August

10 Ideally I d like to bring the entire assembly with both pulleys, the tail shaft, the spur gear and the attaching hardware and have it balanced as a unit. Aside from the cost of balancing the pulleys I left with the impression that the mandrels would cost around $200 a piece. If everyone doing this modification was willing to share the expense then it would be worth it, but then they would have to all send me their pulleys or I d have to send the mandrels all over the world. This is much more work than I want to take on. I think the only reasonable approach is to be as careful as possible and then try it. I already know that I had some engine vibration. If it feels worse then I ll have to deal with it. It is hasn t changed I ll probably live with it. Hold everything I think I can use my Spurling Pro-Drive dynamic balancer which might be perfect for the job. First I ll run the engine and see if I can feel any vibration. I may be worrying unnecessarily. Juan Rivera 8 August

Introduction to Machining: Lathe Operation

Introduction to Machining: Lathe Operation Introduction to Machining: Lathe Operation Lathe Operation Lathe The purpose of a lathe is to rotate a part against a tool whose position it controls. It is useful for fabricating parts and/or features

More information

Installing CNC Stepper Motor Mounts On A Sherline Lathe

Installing CNC Stepper Motor Mounts On A Sherline Lathe Installing CNC Stepper Motor Mounts On A Sherline Lathe P/N 6720 (6725 Metric) 4000/4100/4500/4600 Lathes P/N 6730 (6735 Metric) 4400/4410 Lathe USING THE TEMPLATE BLOCKS TO LOCATE NEW MOUNTING HOLES FOR

More information

VASE FLYING-WING A BARK-EDGED. Kevin Felderhoff. Wood selection. 36 American Woodturner August 2017

VASE FLYING-WING A BARK-EDGED. Kevin Felderhoff. Wood selection. 36 American Woodturner August 2017 A BARK-EDGED FLYING-WING VASE Kevin Felderhoff I enjoy turning endgrain pieces and have found that the most dramatic wood grain comes from logs or branches with irregular shapes far from round. The flying-wing

More information

VARIABLE SPEED WOOD LATHE

VARIABLE SPEED WOOD LATHE MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02

More information

Travis Bishop. Submitted to: Dr. John Davis. Date: 3 December Course: ETME 310 Section: 004. Lab Topic: Milling Project (Vise)

Travis Bishop. Submitted to: Dr. John Davis. Date: 3 December Course: ETME 310 Section: 004. Lab Topic: Milling Project (Vise) Travis Bishop Submitted to: Dr. John Davis Date: 3 December 2012 Course: ETME 310 Section: 004 Lab Topic: Milling Project (Vise) Introduction: Purpose of Experiment: This experiment was conducted to teach

More information

Installing CNC Stepper Motor Mounts On A Sherline Mill

Installing CNC Stepper Motor Mounts On A Sherline Mill Installing CNC Stepper Motor Mounts On A Sherline Mill P/N 6700 (6710 Metric) 5000/5100/5400/5410 Mills P/N 6705 (6715 Metric) 2000/2010 Mills USING THE TEMPLATE BLOCKS TO LOCATE NEW MOUNTING HOLES FOR

More information

Lathe. A Lathe. Photo by Curt Newton

Lathe. A Lathe. Photo by Curt Newton Lathe Photo by Curt Newton A Lathe Labeled Photograph Description Choosing a Cutting Tool Installing a Cutting Tool Positioning the Tool Feed, Speed, and Depth of Cut Turning Facing Parting Drilling Boring

More information

Quill Stop V2 Installation Guide 11/16/2014

Quill Stop V2 Installation Guide 11/16/2014 Thank you for purchasing the Quill Stop for the Sieg X3 (Grizzly G0463) and SX3 (Grizzly G0619) mills. Your feedback is always appreciated. Please email questions and comments to gregpriest@cox.net. What

More information

Simple Dresser. Premium Plan. In this plan you ll find: America s leading woodworking authority

Simple Dresser. Premium Plan. In this plan you ll find: America s leading woodworking authority America s leading woodworking authority Premium Plan In this plan you ll find: Simple Dresser Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos.

More information

7x --Tailstock Cam Lock

7x --Tailstock Cam Lock 7x --Tailstock Cam Lock By Magic Brian magicbrian40@yahoo.com Probably the most pleasing mod to have, but often not done through lack of milling facility s This version does NOT require a mill. MATERIALS

More information

CNC Using the FlexiCam CNC and HMI Software. Guldbergsgade 29N, P0 E: T:

CNC Using the FlexiCam CNC and HMI Software. Guldbergsgade 29N, P0 E: T: CNC Using the FlexiCam CNC and HMI Software Guldbergsgade 29N, P0 E: makerlab@kea.dk T: +46 46 03 90 This grey box is the NC controller. Let s start by turning the red switch to the ON position, then press

More information

Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers

Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers for up to date building information; http://www.mikenchell.com/forums

More information

SOUTH BEND 10 HEAVY LATHE CROSS FEED SCREW REBUILD

SOUTH BEND 10 HEAVY LATHE CROSS FEED SCREW REBUILD The oldest piece of machinery that I have is a South Bend 10 inch heavy lathe. It has become somewhat of a project piece at times having come without a thread dial indicator and a rear cover for the cross

More information

Part Seven. FrankenCasing Overview

Part Seven. FrankenCasing Overview Part Seven FrankenCasing Overview Though a very unique term, it is quite fitting to the practice that it describes. Like the good doctor Frankenstein, the art of FrankenCasing follows the steps of taking

More information

A candle stick addresses transferring and reproducing dimensions from a plan and breaking the project into steps.

A candle stick addresses transferring and reproducing dimensions from a plan and breaking the project into steps. Activities Discussion These projects allow more skill development including making items to match a drawing, sizing projects to specific dimensions, and just trying fun stuff for the first time! A candle

More information

Required Tools: Procedure:

Required Tools: Procedure: Depending on the materials you process through your chipper, their moisture content, the climate you live in, and many other factors you may have difficulty removing the rotor from the engine shaft. The

More information

MODEL T " SPIRAL CUTTERHEAD INSTALLATION INSTRUCTIONS

MODEL T  SPIRAL CUTTERHEAD INSTALLATION INSTRUCTIONS MODEL T27449 8" SPIRAL CUTTERHEAD INSTALLATION INSTRUCTIONS The Model T27449 indexable insert spiral cutterhead is designed to replace the straightknife cutterhead on the Grizzly jointer Model G0490W/G0490XW

More information

VARIABLE SPEED WOOD LATHE. Model DB900 INSTRUCTION MANUAL

VARIABLE SPEED WOOD LATHE. Model DB900 INSTRUCTION MANUAL VARIABLE SPEED WOOD LATHE Model DB900 INSTRUCTION MANUAL 1007 TABLE OF CONTENTS SECTION...PAGE Technical data.. 1 General safety rules....1-3 Specific safety rules for wood lathe.....3 Electrical information.4

More information

INSTALLING T400 LOAD SENSORS

INSTALLING T400 LOAD SENSORS INSTALLING T400 LOAD SENSORS The above illustrations represent the proper arrangement of Model T400 Load Sensor kit parts using either the Drill and Tap method or the Weld method. A proper installation

More information

LocoGear. Technical Bulletin - 02 January 11, by LocoGear LIVE STEAM CASTINGS. Tech Bulletin - 02

LocoGear. Technical Bulletin - 02 January 11, by LocoGear LIVE STEAM CASTINGS. Tech Bulletin - 02 LIVE STEAM CASTINGS Tech Bulletin - 02 LocoGear Technical Bulletin - 02 January 11, 2003 2003 by LocoGear John D.L. Johnson 3879 Woods Walk Blvd. Lake Worth, FL 33467-2359 jjohnson@locogear.com www.locogear.com

More information

WEAR YOUR FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING

WEAR YOUR FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING NOTE: A saddle travel extension is included with this kit to allow the column to be lowered an additional 1.6"

More information

WARNING BX1514. Serial Number Buick LaCrosse Installation Instructions

WARNING BX1514. Serial Number Buick LaCrosse Installation Instructions Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed

More information

Contrivance. sample. a modular mechanism machine. design by Derek Hugger. Important:

Contrivance. sample. a modular mechanism machine. design by Derek Hugger. Important: sample Important: McMaster Carr, a supplier whose part numbers are referenced throughout this document, can only ship within the United States. Builders outside of the U.S. must find an alternate supplier

More information

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide

Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide The following guidelines should be followed to lubricate the three main parts of the 400QMD mount. The QMD stands for Quartz Micro-Drive controller.

More information

Continue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below

Continue gluing the remaining top parts ensuring the angled piece is glued well. Set aside and let dry. See photo below Radiator rev 1.1 The SE5a s radiator is one of the most recognized radiators in WW1. It is one of the components that defines the SE5a. The original SE5a has seen multiple radiator designs used during

More information

The Kruger Eccentric

The Kruger Eccentric The Kruger Eccentric Instructions for Use of the Dual Taper Reel Seat Filler and Eccentric Reel Seat Recess Turning Mandrels Rick Kruger 503-860-6346 krugerr@easystreet.net The Dual Taper Reel Seat Filler

More information

GENERAL NOTES: Page 1 of 9

GENERAL NOTES: Page 1 of 9 Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block

More information

PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0

PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 DYNATRAC PRODUCTS 2003-2010 4X4 DODGE 2500/3500 HEAVY DUTY BALL JOINT PROSTEER BALL JOINT REBUILD INSTRUCTIONS V1.0 WARNING: Improper use or installation of this product can cause major failures that could

More information

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.

Fortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards. Installation Instructions for Fortress Horizontal Cable Panel System with UB-05 Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all

More information

Roller assembly (actual size)

Roller assembly (actual size) Roller assembly (actual size) 7 3.5 of 0.5 deg slope 3.5 of 0.5 deg slope 1.929 for PVC 1.950 for Aluminum 0.030 radial reduction 2.2 approx OD 6.5 11.875 Roller assembly consists of: a. 5/16 x 11.875

More information

MODEL T27697 & T " & 8" HELICAL CUTTERHEADS INSTALLATION INSTRUCTIONS

MODEL T27697 & T  & 8 HELICAL CUTTERHEADS INSTALLATION INSTRUCTIONS MODEL T27697 & T27699 6" & 8" HELICAL CUTTERHEADS INSTALLATION INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com These indexable insert

More information

Inventory (Figure 2)

Inventory (Figure 2) MODEL T10130/T10126 6" & 8" SPIRAL CUTTERHEAD INSTRUCTIONS The Model T10126/T10130 indexable insert spiral cutterheads are designed to replace straightknife cutterheads from the Grizzly jointer Models

More information

Installation Instructions for Vista Air Vertically Folding Walls

Installation Instructions for Vista Air Vertically Folding Walls Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.

More information

8-Direction Vertical Milling Column P/N 3580 (Metric P/N 3585)

8-Direction Vertical Milling Column P/N 3580 (Metric P/N 3585) WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING Note: This is a supplement to the instructions included in the Sherline Assembly and Instruction Guide that

More information

RTI TECHNOLOGIES, INC.

RTI TECHNOLOGIES, INC. RTI TECHNOLOGIES, INC. BRC500 & BRC550 Arbor/Spindle Mechanism Adjustment & Service Technical Instructions The arbor/spindle mechanism of the BRC500/550 is designed to be robust for long life. Occasionally

More information

3.4 V6 MANUAL/AUTO or any 05- PRESENT 5-SPEED TRANSMISSION to cyl. 23 SPLINE GEAR DRIVEN T-CASE KIT INCLUDES: No. Part No. Qty. Ck.

3.4 V6 MANUAL/AUTO or any 05- PRESENT 5-SPEED TRANSMISSION to cyl. 23 SPLINE GEAR DRIVEN T-CASE KIT INCLUDES: No. Part No. Qty. Ck. Page: 1 of 6 KIT INCLUDES: No. Part No. Qty. Ck. Box Description 1. 240-0020 1 Adapter Plate - Tacoma Transmission Adapter 2. 120-0020 1 Hardware Kit - Tacoma Transmission Adapter 3. 100-0001 8 Set Screw

More information

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment. Attachment Tab Height: 13 Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this equipment. Serial Number 1. Blue Ox towing products and accessories

More information

AT ADAPTER INSTALLATION INSTRUCTIONS

AT ADAPTER INSTALLATION INSTRUCTIONS IMPORTANT: THIS IS A HIGH PERFORMANCE PART AND IMPROPER INSTALLATION COULD RESULT IN INJURY OR DEATH! NEVER WORK UNDER AN AUTOMOBILE THAT IS NOT PROPERLY SUPPORTED AND BLOCKED FROM ROLLING. NO CREDIT OR

More information

Builder s Log Helicycle N750G

Builder s Log Helicycle N750G This is the area around the lower left fuel tank. The aluminum bracket at the top of the picture mounts the upper limit switch for the clutch. Notice how the cable harness goes around to the inside of

More information

INSTRUCTIONS

INSTRUCTIONS IMPORTANT: THIS IS A HIGH PERFORMANCE PART AND IMPROPER INSTALLATION COULD RESULT IN INJURY OR DEATH! NEVER WORK UNDER AN AUTOMOBILE THAT IS NOT PROPERLY SUPPORTED AND BLOCKED FROM ROLLING. NO CREDIT OR

More information

ITEM NO. PART NO DESCRIPTION QTY.

ITEM NO. PART NO DESCRIPTION QTY. PUMP MAINTENANCE ITEM NO. PART NO DESCRIPTION QTY. 1 52002 Center Case 1 2 52052 Back End Plate 1 3 52051 Front End Plate 1 4 55090 Octagonal Nut 1 5 53001 Idler Gear 1 6 53002 Drive Gear 1 7 28062 Bushing

More information

Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.

Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment. 2005-08 Pontiac G6 GT Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed

More information

Lecture 18. Chapter 24 Milling, Sawing, and Filing; Gear Manufacturing (cont.) Planing

Lecture 18. Chapter 24 Milling, Sawing, and Filing; Gear Manufacturing (cont.) Planing Lecture 18 Chapter 24 Milling, Sawing, and Filing; Gear Manufacturing (cont.) Planing For production of: Flat surfaces Grooves Notches Performed on long (on average 10 m) workpieces Workpiece moves / Tool

More information

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment. Attachment Tab Height: 19-1/2 Attachment Tab Width: 19 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and

More information

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment. 1997-2006 Jeep Wrangler (Includes Rugged Ridge Double Tube Bumper) Attachment Tab Height: 17-3/4 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing

More information

GEARBOX CONSTRUCTION E.M.G.S. MANUAL ( 9) The Girder Gearbox

GEARBOX CONSTRUCTION E.M.G.S. MANUAL ( 9) The Girder Gearbox GEARBOX CONSTRUCTION SHEET 1 The author, having been disappointed with a few of the commercially available gearboxes, decided to design and construct something to his own design. The Girder Gearbox Application

More information

09 August, 2014 Page 1

09 August, 2014 Page 1 AutoCAD Design of Avionics Stack Top Cover Plate 09 August, 2014 I ve settled on a hybrid method of designing and fabricating most of my sheet metal and milled components for my second Helicycle. I start

More information

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16

Page 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16 R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged

More information

STUDENT/FACULTY MACHINE SHOP SAFETY RULES

STUDENT/FACULTY MACHINE SHOP SAFETY RULES STUDENT/FACULTY MACHINE SHOP SAFETY RULES Supervisors have full authority over the shop and its safe use, including the responsibility, authority, and obligation to prohibit shop or tool access for the

More information

BX Toyota Tacoma (Includes Prerunner) Installation Instructions

BX Toyota Tacoma (Includes Prerunner) Installation Instructions Attachment Tab Height: 11.5 Attachment Tab Width: 30.5" Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and

More information

Instructions for Prepping an Opening for SOSS Invisible Hinges

Instructions for Prepping an Opening for SOSS Invisible Hinges Instructions for Prepping an Opening for SOSS Invisible Hinges IMPORTANT Use only Porter-Cable Template Guide Bushing #42024 (Lock Face Routing) and #42237 (Lock Nut) to assure the following guide bushing

More information

Entrance Cabinet Plans

Entrance Cabinet Plans Entrance Cabinet Plans www.andrewharriswoodwork.com Page 1 of 19 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then

More information

Turning Pendants with the Richard Joyner Eccentric Backer Plate

Turning Pendants with the Richard Joyner Eccentric Backer Plate Turning Pendants with the Richard Joyner Eccentric Backer Plate Vaughn McMillan August 2010 As the result of a great tool sharing effort by my friend Jonathan Shively at http://familywoodworking.org, I

More information

This book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay Tooned, Inc.

This book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay Tooned, Inc. Copyright 2006 - Stay Tooned, Inc. All rights reserved worldwide. This book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay

More information

Guide Pulley System [GPS]

Guide Pulley System [GPS] Guide Pulley System [GPS] The purpose of the guide pulley system is to guide the wire from the dancer pulley system to the guide rollers. Two of these systems exist: on both sides of the machine. The pulley

More information

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment. Attachment Tab Height: 16-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and

More information

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models

w w w. h d o n l i n e s h o p. d e TIMKEN BEARING CONVERSION TOOL GENERAL INSTALLATION -J04672 REV Kit Number Models -J067 REV. 008-07- GENERAL Kit Number 8-08 Models TIMKEN BEARING CONVERSION TOOL For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com

More information

Summer Junior Fellowship Experience at LUMS. Maliha Manzoor 13 June 15 July, 2011 LUMS Summer Internship

Summer Junior Fellowship Experience at LUMS. Maliha Manzoor 13 June 15 July, 2011 LUMS Summer Internship Summer Junior Fellowship Experience at LUMS Maliha Manzoor 13 June 15 July, 2011 LUMS Summer Internship Internship Schedule June 13-17: 2D and 3D drawings in AutoCAD June 20-24: 2D and 3D drawings in AutoCAD

More information

Giraud Tool Company, Inc.

Giraud Tool Company, Inc. Motor Upgrade for Gracey Trimmer This package is intended to allow the user to upgrade their Gracey trimmer with a higher rpm motor and convenience features not found in the production offering. This upgrade

More information

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back

4-8 HSF 250 Patriot. Line Stop Fitting Installation Instructions. Installation Instructions and Best Practices continued on back HSF 250 Patriot Heavy Duty Line Stop Fitting - 4, 6, 8 inch Nominal Sizes Line Stop Fitting Installation Instructions Push and Pin Completion Plug Installation Instructions IMPORTANT: Read installation

More information

What is a fastener? A device to locate or hold parts

What is a fastener? A device to locate or hold parts What is a fastener? A device to locate or hold parts As a repair technician you will become skilled at removing, reconditioning, replacing, and installing fasteners. An important skill to learn is how

More information

Adjusting Backlash on Sherline handwheels

Adjusting Backlash on Sherline handwheels WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING Adjusting Backlash on Sherline handwheels What Is Backlash? Backlash is the amount the handwheel can turn before

More information

Dimensioning: There are a few simple best practices which can help us dimension a working drawing:

Dimensioning: There are a few simple best practices which can help us dimension a working drawing: Dimensioning and Tolerancing Prepared by: Michael Hypes Cornell University Preparation: One of the most common problems for new designers is choosing dimension that do not reflect the purpose of the part.

More information

AFB (AIR FAN BEARING) INSTALLATION GUIDE

AFB (AIR FAN BEARING) INSTALLATION GUIDE 654 AFB (AIR FAN BEARING) INSTALLATION GUIDE AFB PARTS Bearing Housing - Secured together with two 3/8 x 1.25 in. Cap Screws Black Wiper Seals - Secured together with O-ring cord (Subsequently depicted

More information

An Improved Tool Support for a Harbor Freight Tool Grinder, version 2.2

An Improved Tool Support for a Harbor Freight Tool Grinder, version 2.2 An Improved Tool Support for a Harbor Freight Tool Grinder, version 2.2 By R. G. Sparber Copyleft protects this document. 1 Advisory This article was written with a hobby machinist a bit above novice in

More information

Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.

Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment. Serial Number BX1670 Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed

More information

Other Lathe Operations

Other Lathe Operations Chapter 15 Other Lathe Operations LEARNING OBJECTIVES After studying this chapter, students will be able to: Safely set up and operate a lathe using various work-holding devices. Properly set up steady

More information

FUSELAGE CONSTRUCTION

FUSELAGE CONSTRUCTION FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear

More information

DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0

DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0 DYNATRAC PRODUCTS 2007-2016 4X4 JEEP JK HEAVY DUTY BALL JOINT JP44-2X3050-C DYNATRAC BALL JOINT REBUILD INSTRUCTIONS V4.0 WARNING: Improper use or installation of this product can cause major failures

More information

MINI-LATHE QUICK CHANGE TOOL POST

MINI-LATHE QUICK CHANGE TOOL POST MINI-LATHE QUICK CHANGE TOOL POST Cutting and assembly details Machinists should familiarize themselves with the contents of this section before jumping in to the drawings. Many details are described here

More information

Advantages, Function and Characteristics of the DMwriter MX.

Advantages, Function and Characteristics of the DMwriter MX. DMwriter MX All-in One Overview Advantages, Function and Characteristics of the DMwriter MX. The DMwriter MX Marking Head was designed as an easy to use, economical, spindle actuated permanent marking

More information

Wooden Faceplates. Tapping on the Lathe

Wooden Faceplates. Tapping on the Lathe Wooden Faceplates There are lots of turning jobs where spending some time on set-up makes the turning go quicker and easier. Making Wooden Faceplates is one way to make set-ups and jigs for turning. As

More information

Inventory (Figure 2)

Inventory (Figure 2) MODEL T10127 12" SPIRAL CUTTERHEAD INSTRUCTIONS The Model T10127 indexable insert spiral cutterhead is designed to replace the straightknife cutterhead from the Grizzly jointer Model G0609. The total procedure

More information

Butterfly Leaf Dining Table Plans

Butterfly Leaf Dining Table Plans Butterfly Leaf Dining Table Plans Part 1 An attractive dining table with a secret: the leaf folds and stores inside the table. Season 1, Episode 7 P a g e 2 I first saw a butterfly leaf table in a back

More information

Sea Doo Spark Engine Access Kit

Sea Doo Spark Engine Access Kit Sea Doo Spark Engine Access Kit PART# - RS4-130-EAK APPLICATION(S): Sea Doo Spark. 2up & 3up Models. We strongly recommend the use of a service manual to familiarize yourself with the various components

More information

ELECTRIC TOOL CORPORATION

ELECTRIC TOOL CORPORATION Cat. No. -0 / Hex Demolition Hammer Cat. No. 0-0 Spline Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 -9-00 d 000 -9-00 d SpecialTools Require Forcing discs

More information

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment. 2012-15 Hyundai Accent GLS/SE (With Foglights) Attachment Tab Height: 14 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this

More information

V-MOTION LITE USER GUIDE. Rat Rig All rights reserved.

V-MOTION LITE USER GUIDE. Rat Rig All rights reserved. V-MOTION LITE USER GUIDE Rat Rig 2017. All rights reserved. PACKAGE CONTENTS 1 1x V-Motion Motor 2 1x Belt 3 1x 3mm Hex Key 4 1x AA Battery Pack (for 8x AA batteries)* 5 1x V-Motion Controller 6 2x Knob

More information

INSTRUCTIONS

INSTRUCTIONS ENGINE APPLICATION YEARS/CID: FORD, MERCURY 332, 352, 360, 361, 390, 406, 410, 427, 428 1958-1976 TRANS APPLICATION YEAR/MODEL: GM AUTO PG, TH350, 400, 700R4, CHEVY OR UNI-CASE BOLT PATTERN, IMPORTANT:

More information

Procedure for Longworth Chuck construction

Procedure for Longworth Chuck construction Procedure for Longworth Chuck construction Overall construction The Longworth chuck is composed of three major components. Connected to the lathe spindle is some device that fastens to the first of two

More information

What is a fastener? A device to locate or hold parts

What is a fastener? A device to locate or hold parts What is a fastener? A device to locate or hold parts As a repair technician you will become skilled at removing, reconditioning, replacing, and installing fasteners. An important skill to learn is how

More information

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.

Please read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment. Attachment Tab Height: 14 Serial Number Attachment Tab Width: 22 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories

More information

BX1965 Installation Instructions 2004 Chrysler Sebring Convertible

BX1965 Installation Instructions 2004 Chrysler Sebring Convertible BX1965 Installation Instructions 2004 Chrysler Sebring Convertible Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate installation.

More information

Complete Dovetail Jig Instructions

Complete Dovetail Jig Instructions Complete Dovetail Jig Instructions 15 18 4 3 1 12 13 8 19 17 16 6 14 5 9 11 10 2 9 PARTS LIST - Complete Dovetail Jig Introduction Your new dovetail jig will cut Full Through Dovetails and three varieties

More information

A Pictorial of David Dawes AA400 HFT Thumbhole Stock in the Making

A Pictorial of David Dawes AA400 HFT Thumbhole Stock in the Making DRAFT Version A Pictorial of David Dawes AA400 HFT Thumbhole Stock in the Making Part 1 and finally Part 2 as well Updated: February 2008 By James Mitchell (a.k.a. mitchejc) Note: Building rifle stocks

More information

CHAPTER 10. Half-Blind Dovetail Procedures

CHAPTER 10. Half-Blind Dovetail Procedures CHAPTER 0 Half-Blind Dovetail Procedures 6 Chapter 0 D User Guide HALF-BLIND DOVETAIL PROCEDURES Chapter Foreword In these instructions for using the Leigh Dovetail Jig, we have recommended using certain

More information

MODEL H " BYRD SHELIX CUTTERHEAD INSTRUCTIONS

MODEL H  BYRD SHELIX CUTTERHEAD INSTRUCTIONS MODEL H9291 12" BYRD SHELIX CUTTERHEAD INSTRUCTIONS The Model H9291 12" Byrd Shelix cutterhead is designed to replace the straight-knife cutterhead on the Grizzly jointer Model G0609. The total procedure

More information

Sales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd.

Sales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd. Sales & Service sasportonline.com SA Sport (Canada) SA Sport (U.S.A.) 135 Forestview Road 7879 Will Rogers Blvd. P.O. Box 40 Fort Worth, Texas Orillia, Ontario USA 76140 Canada L3V 6H9 Telephone: (705)

More information

WARNING Acura TSX Installation Instructions. B as e plate s BX1012. Serial Number

WARNING Acura TSX Installation Instructions. B as e plate s BX1012. Serial Number B as e plate s BX1012 Please read BOTH these and the General Instructions before attempting to install or operate this equipment. Serial Number 1. Blue Ox towing products and accessories are intended to

More information

WARNING Honda CR-V Honda Element Installation Instructions BX2232. Serial Number

WARNING Honda CR-V Honda Element Installation Instructions BX2232. Serial Number Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who

More information

Inventory (Figure 2)

Inventory (Figure 2) MODEL T24631 8" SPIRAL CUTTERHEAD Installation INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction The Model T24631 spiral

More information

Durham Woodworking Club. January 25, 2016

Durham Woodworking Club. January 25, 2016 Durham Woodworking Club January 25, 2016 The drill press has primarily been a metal working machine since its first incarnation. The purpose of the modern day drill press has been to provide woodworkers

More information

WOOD TOY NEWS SANDING DRUMS & JIGS ISSUE

WOOD TOY NEWS SANDING DRUMS & JIGS ISSUE WOOD TOY NEWS SANDING DRUMS & JIGS ISSUE toymakingplans.com June 11, 2014 Wednesday How to Make a Sanding Drum Jig for Smarter Toymaking. By Imants Udris Udie Our discussion begins based on the 5 piece

More information

Notes for Making Wood Rings With Stainless Steel Insert Centers

Notes for Making Wood Rings With Stainless Steel Insert Centers Notes for Making Wood Rings With Stainless Steel Insert Centers Background These notes describe how to make a ring with a stainless steel (SS) insert and a wood exterior band. They also include information

More information

MODEL T27451/T " & 20" SPIRAL CUTTERHEAD INSTRUCTIONS

MODEL T27451/T  & 20 SPIRAL CUTTERHEAD INSTRUCTIONS MODEL T27451/T27452 15" & 20" SPIRAL CUTTERHEAD INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com The T27451 15" & T27452 20" indexable

More information

Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981

Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981 Page 1 of 12 Date: December 2, 1981 Subject: Models: Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System F-28C and 280C Effectivity: Helicopters manufactured prior to

More information

Referencing 0,0 position

Referencing 0,0 position Page 1 of 11 TITLE: SABRE X-Axis Lead Screw Replacement Procedure Gerber FastFact #: 2013 Supplied by: Gerber Hardware Support Last Modified: March 1, 2011 Summary: The following procedure explains how

More information

Goals and objectives: Process: Set up for spindle turning Practice basic tool cuts o Roughing out o Smoothing o Beads & Coves o Parting & sizing

Goals and objectives: Process: Set up for spindle turning Practice basic tool cuts o Roughing out o Smoothing o Beads & Coves o Parting & sizing First Activities Getting acquainted with the lathe Goals and objectives: Set up for spindle turning Practice basic tool cuts o Roughing out o Smoothing o Beads & Coves o Parting & sizing Process: Mount

More information

customraider.net GPS Accessory Handlebar Mount Installation Manual Install Instructions Revision E 07/31/2011 8/8/2011

customraider.net GPS Accessory Handlebar Mount Installation Manual Install Instructions Revision E 07/31/2011 8/8/2011 customraider.net GPS Accessory Handlebar Mount Installation Manual Revision. E 07/31/2011 Parts List (Fig.1) (included in kit) GPS Accessory Handlebar Mount - Yamaha Raider Installation GPS Accessory Mount

More information

Harriet Chair with Modifications

Harriet Chair with Modifications Harriet Chair with Modifications This modification of the Harriet chair includes a slat back, padded seat, and is 2 inches wider than the original plan. The overall dimensions of the finished chair: 38

More information