INSTALLATION INSTRUCTIONS FOR FLUSH MOUNT FIXTURES
|
|
- Erick Hicks
- 6 years ago
- Views:
Transcription
1 Kurt Versen Company Point Source Lighting Models with Round Apertures 10 Charles Street Westwood, New Jersey 1 PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE INSTALLATION. 2 DISCONNECT ELECTRICAL POWER BEFORE WIRING OR SERVICING FIXTURE. Telephone: Fax: INSTALLATION INSTRUCTIONS FOR FLUSH MOUNT FIXTURES 3 WARNING: DO NOT INSTALL INSULATION WITHIN THREE INCHES OF FIXTURE SIDES OR TOP TO ENTRAP HEAT. PLASTERING PLUG APERTURE PREPARATION 1 Remove plastering plug from aperture assembly. (See Fig. 1) 2 Loosen 3 screws and separate aperture assembly from fixture. (See Fig. 2) 3 NOTE: Protect plastering plug and aperture assembly from any damage by storing them in a safe place until ready for use. Fig. 1 CEILING THICKNESS 1 Place the rail assemblies (packed separately) on the fixture. The rail assemblies may be adjusted to accommodate the following ceiling thicknesses: 3/8, 1/2, 5/8, 3/4 & 7/8 2 Move rail assemblies to the proper slot as indicated on label and firmly tighten wing nuts. (See Figs. 3, 4 & 5) 1/2 3/4 3/8 5/8 7/8 SHEETROCK THICKNESS SETTING Fig. 2 Fig. 4 LABEL WING NUT STEEL WASHER SLOT Fig. 3 Fig. 5 1
2 MOUNTING FIXTURE TO CEILING 1 Determine the space where fixture is to be installed. 2 Measure the space between the joists or T-rails. (See Figs. 6 & 7) NOTE: T-rails must be suitable for gypboard applications. 3 Loosen 8 wing nuts (4 on each side of the rail assemblies) and set the rail lengths to fit the INSTALLATION INSTRUCTIONS WOOD JOISTFOR FLUSH MOUNT FIXTURES Fig. 6 (SUITABLE FOR GYPBOARD) measured space. (See Fig. 8) 4 Tighten 4 wing nuts at the top of the rail assemblies. (See Fig.11) 5 Insert fixture into ceiling space. NOTE: The perforated portions of the rail assemblies must lie flush with joists or T-rails. (See Fig. 10, 11 &12) 6 Anchor rail assemblies as described: For anchoring to wood joists: Hammer the forked tabs into joists then nail or screw rail ends to joists. (See Figs. 9 & 10) Nailing requires a minimum of 2 nails per rail end. (Continued on page 3) Fig. 7 WING NUTS FORKED TAB END WOOD JOIST DRYWALL (BY OTHERS) Fig. 8 PERFORATED PORTION OF Fig. 10 FORKED TAB LIGHTING FIXTURE WINGNUT WOOD JOIST SQUARE END PERFORATED Fig. 9 PORTION OF Fig. 11 A SQUARE MAY BE USED TO INSURE THAT BOTH OF THESE SURFACES ARE FLUSH WITH EACH OTHER 2
3 LIGHTING FIXTURE WING NUT MOUNTING FIXTURE TO CEILING (Continued from page 2) For anchoring to T-rails: Rail assemblies may be mounted parallel or perpendicular to T-rails. (See Figs. 13 & 15) Lock the rails in place with the supplied self-threading screws. (See Figs. 14 & 18) Fig. 12 A SQUARE MAY BE USED TO INSURE THAT BOTH OF THESE SURFACES ARE FLUSH WITH EACH OTHER SQUARE FINAL ADJUSTMENTS (See Fig. 16 & 17) 1 To re-position fixture, loosen 8 wing nuts on the rail assemblies. 2 Move the fixture along the length of the Rails to the desired location. 3 Firmly lock all 8 wing nuts. WINGNUT TOP OF WING NUT Fig. 13 Fig. 16 FIXTURE MAY BE MOVED SIDE - TO - SIDE WINGNUT Fig. 14 Fig. 17 Fig. 15 Fig. 18 3
4 KV4569 Fig. 19 DISTANCE WILL VARY PER MODEL OF FIXTURE LABEL EDGE OF APERTURE PAN PERFORATED PORTION OF (DRYWALL TO BE DRIVEN INTO THIS AREA) Fig. 20 GYPBOARD DRYWALL (BY OTHERS) WIRING 1 Disconnect electrical power before wiring. 2 All electrical connections must be in accordance with local codes and the National Electrical Code. 3 Fixture must be grounded. 4 See fixture installation instruction sheet for specific wiring instructions and/or wiring diagrams. GYPBOARD CEILING INSTALLATION 1 Please read the label located on fixture aperture pan BEFORE installing gypboard. The label indicates where the drywall screws (by others) are to be driven through the gypboard and into the perforated portion of the rail assembly. (See Figs. 19 & 20) 2 Opening in gypboard should be cut to provide ½ clearance around aperture pan throat. 3 Mount gypboard to ceiling structure so that the fixture s aperture pan throat is centered in the ceiling opening. 4 Fasten gypboard to ceiling structure. 5 Drive 2 drywall screws (by others) through the gypboard and into perforated portion of each rail assembly. (See Figs. 20 & 21) CAUTION: Driving screws into areas other than the perforated portions of the rail assemblies may cause permanent damage to the fixture and/or undesirable aesthetic effects. NOTE: Use 3 drywall screws (by others) per rail assembly on fixtures with larger apertures. APERTURE INSTALLATION 1 Insert aperture assembly into aperture pan. (See Fig. 22) 2 Butt aperture assembly up to gypboard face. 3 Lock in place with 3 screws (provided). (See Figs. 22 & 23) Fig. 21 Fig. 22 APERTURE Fig. 23 4
5 Fig. 24 JOINT TAPE (BY OTHERS) APERTURE SCREEN PLASTERING PLUG SPACKLING COMPOUND APPLICATION 1 Apply joint tape so half of the tape covers the gypboard and the other half covers the aperture assembly screen. (See Fig. 24) 2 Insert plastering plug into aperture assembly. (See Figs. 25 & 26) 3 Apply spackling compound over aperture assembly flange up to aperture edge and feather it out onto gypboard to present a a smooth blended appearance. (See Fig. 26) 4 NOTE: It is MOST IMPORTANT to allow spackling compound to DRY THOROUGHLY. COMPLETION 1 To avoid cracking of plaster, score the edges of the plastering plug BEFORE pulling it out of the aperture. 2 Plug may be cleaned and re-inserted to avoid over-spray into the fixture while painting the ceiling. 3 Insert trim into fixture aperture. (See Fig. 27) Fig. 25 Fig. 26 PLASTERING PLUG Fig. 27 5
6 Fig. 28 TORSION SPRING BRACKET REMOVAL AFTER INSTALLATION 1 Disconnect power to fixture before servicing. 2 Allow trim to cool. 3 NOTE: Gloves should be worn to avoid marking the trim with fingerprints. Place finger on top edge of trim and gently pull the trim downward. (See Fig. 28) 3 Squeeze the torsion spring legs together to clear the torsion spring bracket and pull the trim completely out of the fixture. (See Fig. 29) 4 To remove lensed trim from fixture, insert trim removal tool between lens and top edge of trim, then gently pull the trim downward until the trim flange is exposed. (See Fig. 30) 5 Grab trim by the flange and continue pulling the trim downward until it is completely out of the fixture. TORSION SPRING LEG Fig. 29 FLANGE TOP EDGE OF LENS Fig. 30 REMOVAL TOOL QUALITY CONTROL Every effort is made to assure that our products reach the job in perfect condition. We welcome your comments. Kurt Versen Company may change construction periodically without notice as part of its program for product improvement. Every effort is made to insure accuracy in our literature but error or omission could occur. 6
INSTALLATION INSTRUCTIONS FOR FLUSH MOUNT FIXTURES
Kurt Versen Company Point Source Lighting 10 Charles Street Westwood, New Jersey Models with Square or Rectangular Apertures 1 PLEASE READ THIS ENTIRE INSTRUCTION SHEET BEFORE INSTALLATION. 2 DISCONNECT
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationRound or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims
Installation Instructions for 90ELED-WIC Round or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims LED E_L_-L_WI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationInde-Pendants Family. 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-CRxx-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants:
More information2. Connect driver to power source leads. After connections are made, place driver above ceiling. SEE MINIMUM SPACE REQUIREMENTS BELOW.
INSTALLATION INSTRUCTIONS INSTALLATION: 1. Cut proper opening in ceiling. Round: 140mm Ø, Square: 140mm x 140mm 140mm Ø 140mm x 140mm 2. Connect driver to power source leads. After connections are made,
More informationRound or Square Chicago Plenum Down Light Housing with Lamp
Installation Instructions for 90ELED-DCP Round or Square Chicago Plenum Down Light Housing with Lamp LED E_-L_DC. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationLightplane 3.5 Recessed
INSTALLATION INSTRUCTIONS Lightplane 3.5 Recessed LP3.5R Recessed Ceiling IMPORTANT SAFETY INSTRUCTIONS When installing or using this fixtures basic safety precautions must be followed. Read all instructions
More informationInde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P
Inde-Pendants Family 32L Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-Rxx-P Document No. Supplied by Litecontrol 32L Inde-Pendants: Ring (Plaster Trim, Grid and Drywall
More informationInsolroll Clutch Operated Shades Installation Instructions Installation Instructions
All clutch operated shades are shipped fully assembled and ready for installation. Mounting screws are not provided. Screws for chain guide installation to meet the child safety standards are provided.
More informationAWNING / PATIO COVER INSTALLATION INSTRUCTIONS
AWNING / PATIO COVER INSTALLATION INSTRUCTIONS Before You Begin Read the installation instructions thoroughly before beginning the installation procedure. Perspective In the Awning Instructions, Back means
More informationINSTALLATION INSTRUCTION Silo Multiples - New Construction Housing MT-4*15, MT-4*10
IMPORTANT SAFETY INSTRUCTIONS 1. Read all instructions before installing. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
More informationFixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved
Fixed Wall Arm Installation Guide Part number 2002003-001 Rev E 2012 PolyVision Corporation All rights reserved Table of contents Important Safety Instructions... 3 Overview... 4 Important considerations...
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (22-28.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
More informationOB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount
INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More informationInstallation Instructions
edium + Heavy duty READ BEFORE INSTALLING UNIT Preliminary instructions: 1. Check window opening size: the mounting parts furnished with this air conditioner are made to install in a wooden sill double-hung
More informationREAD BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION
edium + Heavy duty READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully
More informationDRYWALL CEILING SPLINE KICKER REFLECTOR DIFFUSER LENGTH TABLE DIFFUSER LENGTH TABLE DESCRIPTION 2' IND 3' IND 4' IND 6' IND 8' IND
SUPPLEMENTAL INSTALLATION TYPE LG-WWD-44, R-WWD-44 & RP-WWD-44 510553-2000 WHICH IS CONTRARY TO THE CONTAINED HEREIN. P/C PG. 1 OF 1 1/4-20 THREADED ROD OR EQUAL SUPPLIED PANHEAD SHEET METAL SCREW HEX
More informationDOWNLIGHT LED SERIES INSTALLATION INSTRUCTIONS
WARNING: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Make sure all
More informationLow Headroom Rear Mount TorqueMaster
Low Headroom Rear Mount Supplemental Instruction Insert This supplemental installation instruction is to be used as a supplement to the main Installation Instruction and Owner s Manual provided with the
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More informationInstallation Instructions For TruLine 1.6A 24VDC
2014 Pure Lighting. All Rights Reserved. Installation Instructions For TruLine 1.6A 24VDC INS# 902-TL1.6A-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationInstallation And Care Instructions. Vertical Honeycomb Shades
Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...
More informationInde-Pendants Family. 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-C-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants: Cylinder (Surface
More informationwith Lamp Install the Housing with Adjustable Bars Installation Instructions for LED E3_-L_DN 1.1 ½ to ¾ ¾ or thicker
Installation Instructions for 90ELED-D Round or Square Type IC, Non-IC Down Light Housing with Lamp LED E_-L_DN. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationSTEP 1 - CEILING PREPARATION
STEP 1 - PREPARATION 1/4-20 THREADED RODS SR FIXTURE SLOT/ IN SHEET ROCK WHIP A) MAKE SLOT IN SHEET ROCK ACCORDING TO RUN INFORMATION, TYPE OF FIXTURE AND REFER TO S REQUIRED (FIGURE 2 - SR* AND FIGURE
More informationInstallation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" Fig.1 Complete Fixture ADJUSTABLE GEARS HIDDEN BEHIND THE LAMP PAN LOCK
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Dual MR16 Round & Square Edge 3.3" 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationRound or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E3_L_-L_DI 1.4
Installation Instructions for 90ELED-DIC Round or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E_L_-L_DI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationINDIVIDUAL MOUNTING: T-Bar
X1 (T-BAR) INSTALLATION INSTRUCTIONS GENERAL NOTES NOTE : Additional support to structural member may be required. Check with local building codes for requirement. 1. Place troffer clamp approx. 6 from
More informationInstallation Instructions
For Medium (15-18.5K) + Heavy duty (-8.5K) Air Conditioner READ BEFORE INSTALLING UNIT To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5
More informationFlowBar Architectural Linear Diffusers F L- 1 0 / F L-15 / FL-2 0 F L- 2 5 / F L-30 I NSTA LL AT IO N & OPER AT I ON M AN UA L
I NSTA LL AT IO N & OPER AT I ON M AN UA L FlowBar Architectural Linear Diffusers F L- 1 0 / F L-15 / FL-2 0 F L- 2 5 / F L-30 I OM F L-1 0/ FL- 15 /FL-20 /FL-25/FL-3 0 FlowBar Installed During Hard Ceiling
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationINSTALLATION GUIDE. Flat Panel Arm Mount MLA100-L. VESA 100x100 compatible. Support 10" to 24" Screens Max Load Capacity: 30 lbs (15 kg)
INSTALLATION GUIDE Flat Panel Arm Mount MLA100-L Support 10" to 24" Screens Max Load Capacity: 30 lbs (15 kg) VESA 100x100 compatible Note: Read entire instruction sheet before you start installation and
More informationINSTALLATION GUIDE Hisense Laser TV Display Screen
INSTALLATION GUIDE Hisense Laser TV Display Screen Before you install this product, read this guide completely and make sure you understand all of the content. ES-G1811M2-1 ENGLISH Product Description
More informationInstallation Operation Care
Installation Operation Care Provenance Woven Wood Shades Standard Cordlock CONTENTS Getting Started: Product View... 1 Tools and Fasteners Needed... 2 Installation: Installation Overview... 3 Mount the
More informationTwo Panel Frameless Bypass Door
INSTALLATION INSTRUCTIONS Two Frameless Bypass Door Series 00 Please Record Model Number From Carton Label Here Please read these instructions carefully to familiarize yourself with the required tools,
More informationInstall Instructions. NewAge Steel Welded Tall Locker
Kit Contains Full Width Adjustable Steel Shelves (4) Height-Adjustable Steel Leveling Legs (4) Aluminum Door Trim (2) 2.5 x ¼ Cabinet Mounting Lag Bolts (4) Large Zinc Plated Mounting Washers (4) 5/8 x
More informationAssembly Instructions for model: VMPR1
Assembly Instructions for model: VMPR1 Congratulations on your purchase! The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LCD/DLP projectors. Its low profile design
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationINSTALLATION INSTRUCTIONS FIXTURE SERIES: SAE 202 MOUNTING TYPE: RECESSED WALL / SLOT PAGE: 1 OF 8
INSTALLATION INSTRUCTIONS FIXTURE SERIES: SAE 202 MOUNTING TYPE: RECESSED WALL / SLOT PAGE: 1 OF 8 90v INNER CORNER KIT "R" (REGRESSED) POSITION CROSS-SECTION VIEW "S" (SHIELDING AT TOP) POSITION CROSS-SECTION
More informationPRO CYC PRO CYC, INC. SYSTEM SUPER 1.5QS
Assembly Instructions System Super 1.5QS Congratulations on your decision to use the world s most advanced and user-friendly cyclorama system. We have taken a great deal of care to create and ship your
More informationTrack Rack. * Track Racks are not lockable
The Track Rack s unique staggered, sliding hook design creates the greatest parking efficiency while still providing easy access to any particular bike. When adding or removing a bike to the rack, simply
More informationInstallation Instructions Standalone or continuous run configurations - 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install trimless drywall versions of TruGroove
More informationINSTALLATION INSTRUCTIONS - CEILING POWER TRAK, HANGER HOOKS AND RACKS I. CONTENTS CEILING POWER TRAK KIT
INSTALLATION INSTRUCTIONS - CEILING POWER TRAK, HANGER HOOKS AND RACKS I. CONTENTS CEILING POWER TRAK KIT QUANTITY DESCRIPTION 2 POWER TRAK, 5 FT LG 4 END CAPS, YELLOW 10 SCREWS, 1 5/8 LG 10 WASHERS, 5/8
More informationInstallation Instructions for TruLine 1.6A 24VDC. Section One: Basic Configuration Options
Doc # 902-TL1.6A_07 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com 2016 PureEdge Lighting. All Rights Reserved. Installation Instructions
More informationRAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER
INSTALLATION INSTRUCTIONS RAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER NOTE: The following instructions provide general guidelines for product installation. For additional information
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationINSTALLATION, I O OPERATION & MAINTENANCE M A N U A L. Flowline. Architectural Linear Diffusers
INSTALLATION, I O M OPERATION & MAINTENANCE M A Flowline Architectural Linear Diffusers N U A L FLH Series: Horizontal High Throw FLV Series: Vertical Jet Throw www.nailor.com INSTALLATION INSTRUCTIONS
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5 Tools Required...6
More informationInstallation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB. Fig.
2015 Pure Lighting. All Rights Reserved. Installation Instructions For Aurora Halogen Accent Housing 3 Round & Square Trimless AH1-ARE, AH1-ARB, AH1-ASE, AH1-ASB 1718 W. Fullerton Ave Chicago, IL 60614
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationSalter Industries Spiral Stair
Salter Industries Spiral Stair The Leader in Spiral Staircases Continuous Sleeve Stair Installation Instructions TOOLS NEEDED: 1. Electric drill with hex chuck and Phillips bit 2. Drill bits 1/8", 1/4",
More informationINSTALLATION GUIDE. Flat Panel Arm Mount BTAR2/37. VESA 200x200 compatible. Support 24" to 37" Screens Max Load Capacity: 80 lbs (36 kg)
INSTALLATION GUIDE Flat Panel Arm Mount BTAR2/37 Support 2" to 37" Screens Max Load Capacity: 80 lbs (36 kg) VESA 200x200 compatible Note: Read entire instruction sheet before you start installation and
More informationAURORA HALOGEN ACCENT HOUSING 3 ROUND AND SQUARE TRIMLESS AH3-ARE3-RBG & AH3-ASE3-RGB INSTALLATION INSTRUCTIONS
AURORA HALOGEN ACCENT HOUSING 3 ROUND AND SQUARE TRIMLESS AH3-ARE3-RBG & AH3-ASE3-RGB INSTALLATION INSTRUCTIONS Fixtures must be installed by a qualified electrician (check with local and national codes
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationMX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP
6-1/4 HANDRAIL W/ VINYL HANDGRIP TYPICAL ASSEMBLY 5 2 BUTT JOINT 12 10 9 1 8 11 6 3 7 4 BUTT JOINT COMPONENT LIST 1 LEFT RETURN 7 UPPER IMPACT ABSORBER 2 RIGHT RETURN 8 LOWER IMPACT ABSORBER 3 OUTSIDE
More informationInstall Instructions for Cabinet Wood Mantels. Please read this manual before installing the suite. This manual should remain with the homeowner.
Install Instructions for Cabinet Wood Mantels Please read this manual before installing the suite. This manual should remain with the homeowner. Index Page #3 Installing the C channels Page #4-7 Installing
More informationCeiling Tile Installations Part 1. Sheetrock Installations Part 2. WolfVision Support 2055 Sugarloaf Circle, Suite 125 Duluth, GA 30097
Ceiling Tile Installations Part 1 Sheetrock Installations Part 2 WolfVision Support 2055 Sugarloaf Circle, Suite 125 Duluth, GA 30097 (877) 873-WOLF support@wolfvision.us 0 EYE Series Mounting Kit Part
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationEDGE Evolution Outline
EDGE Evolution Outline INSTALLATION INSTRUCTIONS Outline Installation....2-5 Outline End Filler Installation...6-9 Outline Outside Corner Installation...10-13 Outline Inside Corner Installation...14-19
More informationNX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP
6-1/4 HANDRAIL W/ VINYL HANDGRIP TYPICAL ASSEMBLY 5 2 BUTT JOINT 12 10 9 1 8 11 6 3 7 4 BUTT JOINT COMPONENT LIST 1 LEFT RETURN 7 UPPER IMPACT ABSORBER 2 RIGHT RETURN 8 LOWER IMPACT ABSORBER 3 OUTSIDE
More informationAssembly Instructions for Model: VMPR1
Assembly Instructions for Model: VMPR1 Thank you for choosing a Sanus Systems Model: VMPR1 ceiling mount. The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LC/LP
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Skylight Manually Operated Honeycomb Shades 20 C8-10-1806 2/15 1 INTRODUCTION Thank you for purchasing our product. Your new shade has been custom built for you from
More informationBionic 4 PERIMETER, CONTINUOUS RUN X3, X7
I NSTALLAT ION INSTRUC TIONS 6 3 /4 6 3 /4 3¾ 5 1 /2 For LP installs, ceiling opening is equal to row length + 3 /4 8 1 /2 4 3 /32 5 1 /4 Flush X7 Shown PARTS SHIPPED SEPARATELY 4 3 /32 5 1 /4 3" Regressed
More informationALL SEASON PATIO COVER
ALL SEASON PATIO COVER 61 Where the All Season Patio Cover is to be attached to the home, create a level line showing where the top of the mounting rail is to be located. Install each section with the
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationSM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL
SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation
More informationSAE of 7 "R" (REGRESSED) POSITION "S" (SHIELDING AT TOP) POSITION. Tools Required
SAE 0 5/6'' Exposed TBar Ceiling FINISHED EDGE WITH JANGLE 90 IC CORNER KIT 5 7/6" 38mm 9/6'' Screw Slot TBar Ceiling "R" (REGRESSED) POSITION 6" CEILING OPENING "S" (SHIELDING AT TOP) POSITION SUPPORT
More informationInstallation Guide. SN-LM42 Brilliance Series Photoluminescent Area of Rescue Signs
Installation Guide SN-LM42 Brilliance Series Photoluminescent Area of Rescue Signs This series consists of the following: Model SN-LM42D Model SN-LM42DR Model SN-LM42S Model SN-LM42SR CAUTION: In order
More informationRAIL 4 INSTALLATION INSTRUCTIONS. RM4DOD Recessed GENERAL SAFETY INSTRUCTIONS: NOTE:
INSTALLATION INSTRUCTIONS RAIL 4 RM4DOD Recessed NOTE: The following instructions provide general guidelines for product installation. For additional information consult the applicable electrical codes
More informationVertical Honeycomb Shades
Step by Step Installation Instructions Vertical Honeycomb Shades Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from Smith+Noble. Your new shades have been
More informationMM540 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM50 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationMM340 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MM30 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE.
More informationEXPLODED VIEW AND PART CALL OUT ASSEMBLING THE METALUX DF SERIES FRAME KIT
EXPLODED VIEW AND PART CALL OUT CUTOUT DIMENSIONS ON PAGE 2 CEILING BRACING (BY OTHERS) SHEET ROCK METALUX DF SERIES FRAME KIT S282 (2'X2') FIXTURE SHOWN FIXTURE SIZE FRAME KIT PART # 2' X 2' DF-22W-U
More informationINSTALLATION TORSION SPRING FRONT OR REAR MOUNT LOW HEADROOM. 1 Cutting Vertical Track. 2 Fully Adjustable Jamb Brackets
TORSION SPRING FRONT OR REAR MOUNT LOW HEADROOM Wayne Dalton, a division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH., 44660 Supplemental insert Copyright 2015 Wayne Dalton, a division of Part
More informationProBuilder Series CoolSmart TV (42PB - sku# )(54PB - sku# )(72PB - sku# )
Compatibility ProBuilder Series CoolSmart TV ProBuilder Series Linear Fireplaces (42PB, 54PB & 72PB) Packing List Convection Manifold (with grill and mounting brackets pre-attached) 5 Diameter Aluminum
More informationINSTALLATION INSTRUCTIONS LARGE FLAT PANEL IN WALL ENCLOSURE Model: PAC-500
INSTALLATION INSTRUCTIONS LARGE FLAT PANEL IN WALL ENCLOSURE Model: PAC-500 Specifications: Designed for in-wall installation spanning a minimum of 3 wood studs, 16" on center. Accomodates MWR, PWR and
More informationINSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System
INSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System IMPORTANT SAFETY INSTRUCTIONS: Read all instructions before installation. Save these instructions for later use.
More informationInstructions for Prepping an Opening for SOSS Invisible Hinges
Instructions for Prepping an Opening for SOSS Invisible Hinges IMPORTANT Use only Porter-Cable Template Guide Bushing #42024 (Lock Face Routing) and #42237 (Lock Nut) to assure the following guide bushing
More informationRetroArcade.us. RETRO ARCADE BARTOP - Model #: UABARTOP
ASSEMBLY INSTRUCTIONS RETRO ARCADE BARTOP - Model #: UABARTOP - Assembly of cabinet in or near final destination is recommended - Measure all doorways and stairways leading to final destination before
More informationStudio Face Xtreme 6020 Installation Instructions (Nickel , Black )
Packing List Face Trim (4 Pieces) (3) Hanging Brackets (9) 3/16 x 1-1/4 Masonry Screws 9/64 Drill Bit Compatibility (2) Lower Brackets w Magnets (2) Lower Facing Plates (4) 2 Drywall Screws Trim Hardware
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationCustomer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR
Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
More informationSB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL
SB-WM-ART1-M-BL Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 90 lbs (41 kg). Use with heavier than the maximum
More informationInstallation Instructions for. Before You Begin TOOLS REQUIRED
Composite Railing System STEP-BY-STEP Installation Instructions for Spectrum Composite Railing Virtually maintenance free 20-year warranty EverNew Spectrum Railing system is designed to work with a number
More information- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS. Factory pre-installed mud flange TOOLS REQUIRED: Phillips screwdriver, 5/16 nut driver.
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install drywall trim versions of TruGroove recessed
More informationInstallation Instructions Parasol Cellular Shades
Installation Instructions Parasol Cellular Shades SlideArch CONTENTS Getting Started: Product View...1 Tools and Fasteners Needed...2 Installation: Installation Overview... Mount the Installation s Inside
More informationIMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED
INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY COMPACT LAMINATE TOILET PARTITIONS 2080 DuraLineSeries 2180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and
More informationINSTALL INSTRUCTIONS WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES NEWAGE STEEL WELDED CABINETRY
NEWAGE STEEL WELDED CABINETRY WELCOME TO THE NEWAGE PERFORMANCE CABINETRY SERIES ALL CABINETS MUST BE MOUNTED TO STUDS ON A SECURE WALL, AS PER THESE INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN SERIOUS
More informationMONKEY BARS OVERHEAD RACK INSTALLATION
MONKEY BARS OVERHEAD RACK INSTALLATION Thank you for purchasing the New Monkey Bars Overhead storage rack. The most innovative overhead rack on the market WARNING THE PROPER INSTALLATION OF THIS STORAGE
More informationProBuilder Linear CoolSmart TV (42PB - sku# )(54PB - sku# )(72PB - sku# )
Compatibility ProBuilder Linear CoolSmart TV ProBuilder Series Linear Fireplaces (42PB, 54PB & 72PB) Packing List Convection Manifold (with grill and mounting brackets pre-attached) 5 Diameter Aluminum
More informationDX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations
ASSEMBLY GUIDE DX-TVMLPTB03 Low-Profile TV Wall Mount For either wood-stud or concrete wall installations Safety information and specifications...2 Tools needed...........................3 Package contents......................3
More information