Paramount MYT Tripod User Guide
|
|
- Jordan Morton
- 6 years ago
- Views:
Transcription
1 Paramount MYT Tripod User Guide Revision 1.1 December, 2014 Software Bisque, Inc. All rights reserved.
2 Table of Contents MYT Tripod Setup and Use... 3 Height Adjustments... 3 Top Plate Adjustment... 7 Leveling the MYT Tripod... 9 Button Head Adjustment Appendix B: User Guide Revision History P age
3 MYT Tripod Setup and Use The Paramount MYT Tripod provides an ultra-stable platform for portable digital imaging with the Paramount Mighty mount. It is designed for portability, ease of use, weighs 20 lbs. and has a capacity of 150 lbs. The legs have carrying handles for ease of transporting and setting up (see Figure 1) and includes a padded carrying case (see Figure 2). Figure 1: Paramount MYT Tripod retracted Figure 2: Paramount MYT Tripod with case Height Adjustments The Paramount MYT Tripod has three different locking positions. When fully retracted for transport, it measures at 25 in. (64 cm). There are also two operational heights. The tall height is 31 in. (79 cm), see Figure 3, and short height is 27.5 in. (70 cm); see Figure 4. 3 P age
4 From each of these heights, the legs can be extended up to another 5 in. (13 cm) to accommodate unleveled ground, or to increase the tripod s maximum height. The end of each leg has a steel swivel foot to conform to uneven mounting surfaces. Figure 3: Tall height, 31 in. (79 cm). Figure 4: Short height, 27.5 in. (70 cm). The tripod height position locking knob is located on the center ring that adjusts the height of the tripod and can be seen in Figure 5. When this knob is unscrewed so the tip does not engage the stainless steel detent, the center ring is free to slide up and down. By lifting up on the top plate the legs will expand and slide between the different height positions. Once you have reached your desired height, the knob must be tightened until it fully engages and presses against the stainless steel detent. With the knob screwed all the way in, there are two button heads on the opposite side of the tube (Figure 6) as the position locking knob should and they should sit right on top of set screws in the center ring (Figure 7). This ensures that the contact points are on stainless steel, resulting in less force exerted on the aluminum tube. If the knob is fully tight, but the contact of the set screw is not quite right, see Button Head Adjustment on page 11 on how to make this adjustment. (This should not need to be adjusted frequently.) 4 P age
5 Figure 5: Height position lock knob. 5 P age
6 6 P age Figure 6: Button head contact points.
7 Figure 7: Button head and set screw contact. Top Plate Adjustment The top plate has dimensions of 7-¼ in (18.4 cm) as shown in the technical drawing in Figure 8. The top plate also rotates 360 to assist in polar alignment. The knob located on the top plate (Figure 9) loosens and secures down the top plate from rotating. This adjustment should be done before mounting the Paramount MYT on the tripod. It is good practice to tighten this knob all the way down when you have the approximate location however the top plate can be rotated with a bit of force after the Paramount MYT is attached. The tighter the knob after this adjustment, the less room for movement there will be during use. 7 P age
8 8 P age Figure 8: Top plate drawing.
9 Figure 9: Top plate and knob. Leveling the MYT Tripod There are three bubble level and arrow pairs machined in to the bottom ring of the tripod as shown in Figure 10. These arrows point to the leg that the bubble level corresponds with see examples highlighted in blue in Figure 11. Use these levels as well as the bubble level on top of the mounting plate to help get your tripod as level as possible before mounting the Paramount MYT. 9 P age
10 10 P age Figure 10: Leveling arrows
11 Figure 11: The blue arrow points to the leg to raise or lower for this level bubble. Button Head Adjustment The Paramount MYT Tripod has been designed to ensure there are stainless steel on stainless steel contact points. These contact points are on the opposite side of the tripod as the ring locking knob as shown in Figure 12. There is a minor adjustment that can be done to ensure they are contacting in the correct spot. (Again, this adjustment is not something you should have to do often.) 11 P age
12 Figure 12: Stainless steel set screws circled in yellow There are two 3/8-24 set screws stacked on each other in each of the two contact spots. The set screw closest to the center tube you can look at from above the tripod and should be able to see it touching the top of the button head cap screw as shown in Figure 13. The one stacked behind the first set screw is there to prevent the first from moving or coming unscrewed. The only time you should need to adjust these screws are when the locking knob is screwed all the way in and the button head cap screws are not making enough or good contact on the set screws. 12 P age
13 Figure 13: Set screws in transparent ring 13 P age
14 Appendix A: User Guide Revision History Revision Number Changes 1.1 Added Table of Contents. Added page numbers. Minor formatting corrections. 1.0 Initial publication. 14 P age
Assembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationABSL Model Background Stand
ABSL Model Background Stand Product Overview: The Ravelli ABSL model background stand is adjustable up to 13' tall by 15' wide. It is comprised of two tripod stands and five 3 cross bar sections and includes
More informationUsage and Assembly Instructions
Instructions #1037447 Product #795234 Revision D Usage and Assembly Instructions Rear Fork (Buttstock) Rear Fork Lock Knob Rail Lock Knob Front Fork (Forend) Rails Tilt Friction Knob Rail Extension Locks
More informationNUMBERALL STAMP & TOOL CO., INC. USER MANUAL & PARTS LIST S/N: P.O. BOX 187, 1 HIGH ST. SANGERVILLE, ME TEL: FAX:
NUMBERALL STAMP & TOOL CO., INC. USER MANUAL & PARTS LIST MODEL 301 S/N: P.O. BOX 187, 1 HIGH ST. SANGERVILLE, ME 04479 www.numberall.com office@numberall.com TEL: 207-876-3541 FAX: 207-876-3566 MODEL
More informationSTEP 1 STEP 6 STEP 5 STEP 1 STEP 3 STEP 4 STEP 7
Step 1:Attach the tube join support by sliding in tube into legs, make sure height of the 2 legs are the same. Step 2:Attach the second join support in front of the tube join support using provided allen
More informationComponents of Gauge and Overview:
Cat 30 (Standard) and Cat 31 (Metric) Product Information and Usage Guide (Import) (Metric is used in demonstrations) Metric Standard Components of Gauge and Overview: The CAT 30 (standard) and CAT31 (metric)
More informationUsage and Assembly Instructions
Instructions #1037447 Product #795234 Revision C Usage and Assembly Instructions Rear Fork (Buttstock) Rear Fork Lock Knob Rail Lock Knob Front Fork (Forend) Rails Tilt Friction Knob Rail Extension Locks
More informationMK52 Series ULTRA-LOW FREQUENCY VIBRATION ISOLATION WORKSTATION ASSEMBLY AND OPERATION INSTRUCTIONS
MK52 Series ULTRA-LOW FREQUENCY VIBRATION ISOLATION WORKSTATION ASSEMBLY AND OPERATION INSTRUCTIONS i Information contained in this document is subject to change without notice and does not represent a
More informationELECRAFT KXPD1 PLUG-IN KEYER PADDLE
Introduction ELECRAFT KXPD1 PLUG-IN KEYER PADDLE Assembly and Operating Instructions Revision B, July 27, 2011. Copyright 2011, Elecraft; All Rights Reserved The KXPD1 is a unique plug-in keyer paddle
More informationAstro-Physics Inc. 400QMD Lubrication/Maintenance Guide
Astro-Physics Inc. 400QMD Lubrication/Maintenance Guide The following guidelines should be followed to lubricate the three main parts of the 400QMD mount. The QMD stands for Quartz Micro-Drive controller.
More informationSAFETY AND OPERATING MANUAL. Portable versatile workstation
SAFETY AND OPERATING MANUAL Original instructions Portable versatile workstation wu063 1 2 3 4 5 6 7 8 9 Safety instructions Warning! When using this product basic safety precautions should always be followed.
More informationINSTRUCTION SHEET. PIECE INVENTORY - MOBILE BASES Refer to the diagram for part identification.
INSTRUCTION SHEET D2260 HEAVY-DUTY MINI-MOBILE BASE D2057 HEAVY-DUTY MOBILE BASE D2058 SUPER HEAVY-DUTY MOBILE BASE D2259 EXTENSION KIT FOR D2260/D2057 D2246 EXTENSION RAIL KIT FOR D2058 This Shop Fox
More informationHigh Rise Adjustable Stand-Up Desk Converter
High Rise Adjustable Stand-Up Desk Converter Assembly Instructions for Model DC200 Patent Pending PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the
More informationQuill Stop V2 Installation Guide 11/16/2014
Thank you for purchasing the Quill Stop for the Sieg X3 (Grizzly G0463) and SX3 (Grizzly G0619) mills. Your feedback is always appreciated. Please email questions and comments to gregpriest@cox.net. What
More informationBLT ERGO-E.EAZY
1 BLT-82493 Adjustable Pneumatic Computer Desk Assembly Instructions Computer Desk Part Drawing Description Qty Part Drawing Description Qty P1 Top Platform 1 EA P11 Cable Management Tray 1 EA P2 Upper
More informationINSTRUCTION MANUAL. In vivo Test Apparatus for 305B Muscle Lever Systems
INSTRUCTION MANUAL Model 806A In vivo Test Apparatus for 305B Muscle Lever Systems May 18, 2005, Revision 3 Copyright 2005 Aurora Scientific Inc. Aurora Scientific Inc. 360 Industrial Parkway S., Unit
More informationStarizona CGEM Landing Pad
Starizona CGEM Landing Pad The Starizona CGEM Landing Pad is designed to make setting up and polar aligning a Celestron CGEM or CGEM DX equatorial mount much simpler. The Landing Pad can remain attached
More informationSAFETY INSTRUCTIONS. Wear protective clothing, including safety glasses and steel toe boots.
SAFETY INSTRUCTIONS Wear protective clothing, including safety glasses and steel toe boots. DO NOT allow loose clothing or long hair near machine operations. Keep work site and machine clean. Use brush
More informationF i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1
F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1 1 P a r t s L i s t : S t a n d a r d L a n d i n g G e a r U p g r a d e Product Code Parts + Spares Product Code Parts + Spares
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Main illustration: Premier Combo Chair with Arm Rest deployed Arm Rest extended Rifle Stock Rest Shotgun Format Premier Combo Chair (Rifle and Shotgun Chair Combined) with Arm Rest
More informationBY ALIEN TECHNOLOGIES CORP
BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support
More informationPhone #: (360) Online Tech Support: Web:
Phone #: (360) 734-3482 Online Tech Support: tech-support@shopfox.biz Web: www.shopfox.biz Your new Model D2058A Super-Heavy Duty Mobile Base () is designed to give you a stable and mobile platform upon
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationBath Accessory Installation
Bath Accessory Installation Step 1 - Clean surface using a clean dry cloth or use rubbing alcohol to remove any residue (wax, grease, solvents). Allow to dry one hour. Caution! DO NOT use any household
More informationMODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS
MODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS FOR MODELS MFD. SINCE 10/17 For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Rails Rollers Reversible
More information4000 Watt - Metal Halide - Three Stage Light Tower - 30 Feet
4000 Watt - Metal Halide - Three Stage Light Tower - 30 Feet Part #: LM-30-3S-4X1000W Page: 1 Made in the USA The LM-30-3S-4X1000W Light Tower from Larson Electronics is a 30 foot extendable light tower
More informationSINCE 1922 P UBLICATION N O
SINCE 1922 GARED SPORTS MICRO-Z SET-UP INSTRUCTIONS VERY IMPORTANT! READ INSTRUCTIONS CAREFULLY AND FOLLOW STEP BY STEP SET-UP PROCEDURE P UBLICATION N O. 5 5 1 7 5 2 9 1 6 Recommended tools and accessories.
More informationStainless Steel Bench Stand
Installation Manual Stainless Steel Bench Stand Product(s): 29600 29601 51229 2016 by Fairbanks Scales, Inc. Revision 2 02/16 All rights reserved. Amendment Record STAINLESS STEEL BENCH STAND Document
More informationBig & Tall Executive Chair Assembly Instructions
Designed to be comfortable, and built to stay that way. Big & Tall Executive Chair Assembly Instructions 400 lbs Model 50106E PARTS A B C D Casters Quantity: 5 Star Base Quantity:1 Gas Lift Quantity: 1
More informationCut-True 16M Manual Paper Cutter
Cut-True 16M Manual Paper Cutter 2/2013 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS TOPIC PAGE Specifications 1 Safety Guidelines 1 Assembly 2 Overview 3 Description of Equipment Parts 3-4 Operation
More informationCaution: Installation and Operation Instructions. Locking Mechanism (if supplied) Set Screws Backed Out. Mounting Orientation
Genie Probe Regulator (GPR)/ Genie Probe (GP2)/ Genie Probe for Composite Sampler (CSA)/ And (Model H) Installation and Operation Instructions Caution: Not designed for external fire. Prior to use in a
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationBasic steps to time the Gammill quilting machine s rotary sewing hook
Basic steps to time the Gammill quilting machine s rotary sewing hook 1.) Turn the machine off and unplug it. 2.) With the needle bar in the raised position, remove the bobbin and bobbin case. 3.) Remove
More informationAssembly, Use and Care Instructions
Assembly, Use and Care Instructions Product #336677 Instruction #1068318 Rev. F Thank you for purchasing a Caldwell Lead Sled DFT 2. The Lead Sled DFT 2 comes to you partially assembled. It will require
More informationPage 1. SureMotion Quick-Start Guide: LACPACC_QS 1st Edition - Revision A 03/15/16
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LACPACC-002 LACPACC-003 LACP-16TxxLP5 (0.5-in lead screw pitch) LACP-16TxxL1 (1-in lead screw pitch) C P I R K 4 ea Flanged
More informationGP-SD GENIE PROBE SMALL DIAMETER
For GENIE PROBE SMALL DIAMETER Installation and Operation Instructions 2 for s Locking Mechanism (if supplied) Set Screws Backed Out To ensure that the is Locking never accidentally loosened or Mechanism
More informationS E L E C T I O N. Arm Curl. User manual
S E L E C T I O N T H E S T R E N G T H E V O L U T I O N User manual The identification plate of the and manufacturer, affixed behind the seat, gives the following details: A Name and address of the manufacturer
More informationCustomer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR
Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from
More informationSide Winder R o u t e r L i f t.
Woodpeckers PRECISION WOODWORKING TOOLS Side Winder R o u t e r L i f t. INSTALLATION INSTRUCTIONS The wrench handle must be pointing left in order to fully insert or remove it. Lift Wrench Once fully
More informationUltraFeed Feeder Operator s Manual
UltraFeed Feeder Operator s Manual Version 1.1 Table of Contents Topic Page Safety Statement and Recommendations 3 General Operation and Set-Up 5 Control Panel Operation 6 Set Up and Operation 7 Set Up
More informationQUICK START GUIDE. ROTAPRINT Rotary Printing Attachment. for ROLAND LEF-12/20/200/300
QUICK START GUIDE ROTAPRINT Rotary Printing Attachment for ROLAND LEF-12/20/200/300 Rev 2 - September 2017 Welcome to the World of Spherical Printing The challenge of short run digital spherical printing
More informationAssembly Instructions. Table of Contents
HQ Little Foot Assembly Instructions Back of Handi Quilter, Inc. 501 North 400 West North Salt Lake, UT 84054 1-877-697-8458 Front of 2015 Handi Quilter, Inc. www.handiquilter.com Printed in the United
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS ITEM No. :Quilty/ 3 A helpful Assembly Video can be found on www.arrowcabinets.com in the Video Section under Quilty Incorrect Correct The turning direction of attaching The arrow
More informationMODEL T28000 HEAVY-DUTY MOBILE BASE INSTRUCTIONS
MODEL T28000 HEAVY-DUTY MOBILE BASE INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction Your new Model T28000 Heavy-Duty
More informationMotorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions
Motorized or Crank Operated Fortress Zipper Track Shade with Housing and Side Track Installation Instructions Tools Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil 4 Level Phillips
More informationDiptych Bath Screen Installation Guide
v1 These instructions are for left and right handed screens. The diagrams show a right handed screen. Page i Thank you for purchasing this Diptych Bath Screen. Please study these instructions carefully
More informationUS RACK, Inc Falcon Drive, Madera, CA
US RACK, Inc. - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTRUCTIONS for MOTORCYCLE RACK with Cradling Wheel Chocks WARNING: Do NOT attempt to install or use this rack without following all instructions.
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationHonda Gold Wing GL1800 Floorboards Installation Instructions #GL18020
Honda Gold Wing GL1800 Floorboards Installation Instructions #GL18020 1. Place the motorcycle on its centerstand. Remove the left and right stock foot pegs and mounts (four Allen screws, 6mm wrench size).
More informationSTRINGING MACHINE OWNER'S MANUAL. Copyright 1998 GAMMA Sports - All Rights Reserved
6002 STRINGING MACHINE OWNER'S MANUAL Issue 3 - June 20, 1998 Copyright 1998 GAMMA Sports - All Rights Reserved 6002 OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3... ASSEMBLY
More informationXI. Rotary Attachment Setups
XI. Rotary Attachment Setups 1) Turn off the laser. 2) Put the rotary attachment onto the engraving table. Ensure the two screw holes on right side of rotary attachment match the two corresponding holes
More informationSliding Door Kit
YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE DOOR KIT. Thank you for purchasing this GrowSpan door kit. When properly assembled and maintained, this product will provide years of reliable
More informationPage 1. SureMotion Quick-Start Guide: LARSACC_QS 1st Edition - Revision A 03/15/16. Standard Steel Bolt/Screw Torque Specifications
R K C T I Repair Kit Product Compatibility Repair Kit # Linear Actuator Assembly # LARSACC-013 LARSACC-014 LARSD2-08T12BP2C (12-in travel) LARSD2-08T24BP2C (24-in travel) C P I R K 1 ea Ball Screw with
More informationinstallation guide 1 GUIDE#: PWB-wwpontoon-pol-004
f250 pontoon WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This WakeWorks tower fits Pontoon boats with 96 to 102 inch wide beam widths. This measurement is taken from
More informationHigh Rise Sit-Stand Desk Converter
High Rise Sit-Stand Desk Converter Assembly Instructions for Model DC350 Patent No. 9,332,839 PRE-ASSEMBLY Please read all instructions before beginning assembly. We strongly recommend you watch the video
More informationDepending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12
XL Quilting Frame 1 Depending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12 Foot frame Printed 2 June 2014 Updated
More informationPFT CABLE GYM INSTRUCTION MANUAL
PFT CABLE GYM INSTRUCTION MANUAL QUESTION? As a quality home gym supplier we are committed to your complete satisfaction. If you have questions, or find missing or damaged parts, we will guarantee your
More informationS48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM
PAGE 1 OF 6 PORTA-DOCK, INC. S48-L12-SC AND G48-L12-GC STEEL PORTA-DOCK S82 SC 6 X 12 PLATFORM AND G82 GC 6 X 12 PLATFORM Thank you for purchasing our product! *Please read these instructions and follow
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More informationmodel tsa-sa48 Sliding Crosscut Table installation guide
model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationOasis Recliner Disassembly Instructions
These instructions may be used to disassemble all versions of our Oasis Recliner seating line and available options. Time Required: 20 minutes. (Internal metal frame) D: Reaching up and inside the back,
More informationMODEL T10815 GRINDING ATTACHMENTS INSTRUCTIONS
MODEL T10815 GRINDING ATTACHMENTS INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Introduction Designed to work exclusively with the
More informationMODULAR BUMPER INSTALLATION MANUAL
MODULAR BUMPER INSTALLATION MANUAL Parts List* 1 Center section 1 Side extension, passenger / right 1 Side extension, driver / left 1 Side cap, passenger / right 1 Side cap, driver / left 1 Brush guard,
More informationSmall tripod buying guide You need a new tripod. Maybe this can help you! Here you'll find a description of the Benro TMA48CL Mach
Small tripod buying guide You need a new tripod. Maybe this can help you! Here you'll find a description of the Benro TMA48CL Mach So I needed a better tripod in terms of maximum load, weight and stability
More informationSpiral Slide
IMPORTANT Page 1 PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationDouble-Ridged Waveguide Horn Antennas
Models 3112, 3106B, 3119, 3115, 3117, 3116C Double-Ridged Waveguide Horn Antennas User Manual ETS-Lindgren Inc. Although the information in this document has been carefully reviewed and is believed to
More informationDeRosa DRM-516 (5-PIECE 16 ) Drum Kit ASSEMBLY INSTRUCTIONS
DeRosa DRM-516 (5-PIECE 16 ) Drum Kit ASSEMBLY INSTRUCTIONS Along with reading this guide, we also recommend that you watch the DeRosa 516 Drum Kit Assembly video on the Austin Bazaar Product FAQ page
More informationRachel
http://gmv.cast.uark.edu A Method Store for Advanced Survey and Modeling Technologies Mon, 01 Apr 2013 03:29:18 +0000 en-us hourly 1 http://wordpress.org/?v=3.5.1 http://gmv.cast.uark.edu/scanning/guide-to-leveling-andaligning-the-breuckmann-tripod-and-smartscan-he-for-calibration/
More informationINSTRUCTION MANUAL DWX723-XE HEAVY-DUTY MITER SAW STAND FINAL PAGE SIZE : 8.5IN X 5.5IN
INSTRUCTION MANUAL DWX723-XE HEAVY-DUTY MITER SAW STAND FINAL PAGE SIZE : 8.5IN X 5.5IN DWX723-XE MITER SAW STANDS Components List A. Beam B. DW7231 Miter saw mounting brackets C. Extension arm D. DW7232
More informationinstallation guide 1 GUIDE#: pwb-assault-001
assault WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This Aerial wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the
More informationSCITEX Dual Roll Kit. User s guide
SCITEX Dual Roll Kit User s guide 2011 Hewlett-Packard Development Company, L.P. First edition Legal notices The information contained herein is subject to change without notice. The only warranties for
More informationAdjusting 45 Compass Hardware Including 4-Point
Adjusting 45 Compass Hardware Including 4-Point Compass Hardware - US Patent No. 7,104,610 & 7,891,739 Apparatus for Mounting a Wheelchair Back Quick Release Fixed 4-Point The information in this manual
More informationPressure Vessel Assembly Instructions
Pressure Vessel Assembly Instructions 1) Measure aluminum tube outer diameter 2) Machine both end caps and only drill pilot holes for all hoes shown 3) Weld both end caps onto the aluminum tube and be
More informationNo. 412, 414, 416 Operations Manual
No. 412, 414, 416 Operations Manual CARE: Occasional oiling of moving parts with machine oil will ease operation and extend the life of the brake. Occasionally check and tighten the lower beam bracket
More informationCleanBench Laboratory Tables
CleanBench 63 Series High-Performance Lab Tables... 2 Accessories Faraday Cages...11 SpaceSaver Overhead Rack...21 Support Bars...27 Sliding Shelves...37 Perimeter Enclosure...37 Casters...38 63-600 Series
More informationE LJ TJ LASER MEASURING DEVICE INSTRUCTIONS
Green Sight Laser Distance Measuring Laser 6 meter Aluminum Rail Weighted Steel Bases! WARNING: This product can expose you to Titanium Dioxide, which is known to the State of California to cause cancer.
More informationThank you for purchasing out product! *Please read these instructions and follow them step by step. *
Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside
More informationMast and Antennas for Field Day & Emergencies
Mast and Antennas for Field Day & Emergencies John A. Allocca, WB2LUA, July 2005 This is a 27 feet 1.5 diameter portable guyed mast with a 28 feet diameter footprint. It breaks down into four 6 feet sections
More informationTL4100 Top 5 Build Tips
TL4100 Top 5 Build Tips 1: Top Plate When assembling the top plate, align the top of the top plate brackets with the top of the rods. This can be done by placing a hard flat object (such as a ruler) on
More informationVIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4
PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationOperating, Servicing, and Safety Manual Model " Foot Shear CAUTION: Read and Understand
Operating, Servicing, and Safety Manual Model 3000 52" Foot Shear CAUTION: Read and Understand These Operating, Servicing, and Safety Instructions, Before Using This Machine. SAFETY The purpose of the
More informationU.S. Rack, Inc Falcon Drive, Madera, CA APR17 INSTALLATION AND USE INSTRUCTIONS for SIDE-MOUNT LADDER RACK
U.S. Rack, Inc. 2850 Falcon Drive, Madera, CA 93637 15APR17 INSTALLATION AND USE INSTRUCTIONS for SIDE-MOUNT LADDER RACK WARNING: Do NOT attempt to install or use this rack without following all instructions.
More informationSTRINGING MACHINE 6 POINT MOUNTING. OWNER'S MANUAL Issue 6 - March 2007
STRINGING MACHINE 5003 6 POINT MOUNTING OWNER'S MANUAL Issue 6 - March 2007 OWNER S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2...FEATURES PAGE 3... PACKAGE CONTENTS PAGE 4... ASSEMBLY INSTRUCTIONS
More informationSliding Crosscut Table installation guide
Sliding Crosscut Table installation guide model tsa-sa48 A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More informationThank you for purchasing our product! *Please read these instructions and follow them step by step.*
07/07/08.rev1 PAGE 1 OF 11 601AL VERTICAL 60120VL LIFT W/CHAIN DRIVE WINCH Thank you for purchasing our product! *Please read these instructions and follow them step by step.* Step 1. Separate and group
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PARTS REQUIRED Single QuickStand Lite Parts A (1) Lower Arm A B C D B (1) Upper Arm C (1) Base D (1) Base Plate E (1) M8 Dynamic Arm Long F (1) Clamp Bracket G H (1) VESA Plate
More informationWORK SUPPORTS WORK SUPPORTS
COMPACT PNEUMATIC Part No. AMNS-S PNEUMATIC Part No. BJ370 PRECISION SUPPORT Part No. BJ371 Part No. BJ350 CYLINDRICAL Part No. BJ351 COIL SPRINGS FOR CYLINDRICAL Part No. BJ351-C REMOTE-CONTROL UNITS
More informationVISAGE SCREEN SYSTEM - FOUR SIDED (FLAT PACK) OPERATIONAL, ASSEMBLY & FIXING INSTRUCTION LEAFLET
TM VISAGE SCREEN SYSTEM - FOUR SIDED (FLAT PACK) OPERATIONAL, ASSEMBLY & FIXING INSTRUCTION LEAFLET NOTE: Ensure that all relevant personnel read the points listed below and that a copy is passed on to
More informationSupplement. Assembly and Maintenance Guide Titan Series Commercial Step System. Manufactured in the USA
Supplement Assembly and Maintenance Guide Titan Series Commercial Step System Manufactured in the USA IMPORTANT! Read and follow all labels and assembly instructions including warnings and cautions prior
More informationIMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS
IMPORTANT -- SPECIAL INSTALLATION INSTRUCTIONS ** READ ALL INSTALLATION INSTRUCTIONS BEFORE STARTING!** If at any point, you have questions, call 1-800-851-0865...(The manufacturer will not be responsible
More information400GTO Lubrication Guide
400GTO Lubrication Guide Lubrication Guidelines for the following equatorial mounting: 400GTO Servo with GTOCP2 or CP3 Controller For other 400 models please review other postings as they become available.
More informationPage 1. ultimatesupport.com
Stop Dreaming. Start Doing. Page 1 Main Menu click on category links Studio Desk 3 Keyboard Stands 4 Benches 4 Amplifier Stands 5 Guitar Stands ( Accessories) 5-6 Pedalboard 6 Guitar Hangers 6 Speaker
More informationProtractors / Clinometers / Spirit levels
Protractors / Clinometers / Spirit levels Accuracy of clinometers/spirit levels according DIN 877 Graduation Flatness (µm) µm/m " (L = length in ) 50 10 4 + L / 250 > 50-200 > 10-40 8 + L / 125 > 200 >
More informationSales & Service. JFK - Just For Kids. sasportonline.com. 135 Forestview Road 7879 Will Rogers Blvd.
Sales & Service sasportonline.com SA Sport (Canada) SA Sport (U.S.A.) 135 Forestview Road 7879 Will Rogers Blvd. P.O. Box 40 Fort Worth, Texas Orillia, Ontario USA 76140 Canada L3V 6H9 Telephone: (705)
More informationHFp. User s Guide. Vertical. entenna. 7 MHz 30 MHz Amateur Radio Antenna Plus 6-Meters
User s Guide HFp Vertical 7 MHz 30 MHz Amateur Radio Antenna Plus 6-Meters The Ventenna Co. LLC P.O. Box 2998, Citrus Heights, CA, 956 www.ventenna.com entenna Table of Contents The HFp Antenna -------------------------------------------------------------------
More informationModel 3104C. Biconical Antenna. User Manual
Model 3104C Biconical Antenna User Manual ETS-Lindgren L.P. reserves the right to make changes to any product described herein in order to improve function, design, or for any other reason. Nothing contained
More information