PRODUCT SELECTION GUIDE - FACE GROOVING
|
|
|
- Walter Barber
- 6 years ago
- Views:
Transcription
1 PRODUCT SELECTION GUIDE - FACE GROOVING PAGE 2-3 For internal diameters of.125" and larger Groove widths.004"-.250" Solid carbide shanks in 1/8", 3/16", 1/4", 5/16", 3/8" and 1/2" diameter FACE GROOVING PAGE 2-5 PAGE 2-7 For internal diameters of.415" and larger Groove widths.004"-.125" For depth of cut up to.125" can groove, bore and generate profiles For internal diameters of 1.574" and larger Groove widths 2, 3, 4, 5 and 6mm For depth of cut to 1" s can also be used for parting and OD/ID grooving PAGE 2-9 PAGE 2-9 PAGE 2-11 Major diameters of.300",.750", 1.250" & 3" Groove widths.004" to.150" in.001" increments Depth of cut 2-1/2 to 3 times width can groove, turn and generate profiles Major diameters of.300",.750", 1.250" & 3" Groove widths.004" to.150" in.001" increments Depth of cut 2-1/2 to 3 times width can groove, turn and generate profiles For dovetail o-ring grooves Groove widths.030",.050",.070",.100",.125" &.150" Back clearance 24 (66 undercut) Major diameters starting from.300" PAGE 2-13 For static o-ring grooves Groove widths.086",.103",.122",.138" &.125" 7 included angle Major diameters starting from.300" Scan this code for additional information. PAGE 2-15 Groove widths 2, 3, 4, 5 and 6mm For depth of cut to 1" s can also be used for parting and OD/ID grooving 2-1
2 TOOLING ORIENTATION GUIDE - FACE GROOVING Left Left Chuck Right Left External Face Grooving Top View Tools shown cutting edge up. FACE GROOVING Right Right Left Chuck Left Right Internal Face Grooving Top View Tools shown cutting edge up. Right 2-2
3 Internal face grooving for diameters.125" and larger. Elliptically ground necks for greater strength. PRODUCT.004" through.250" in.001" increments available. 1/8", 3/16", 1/4", 5/16", 3/8" and 1/2" shanks. Sub-micron grain DURA-MAX 2000 Carbide. s available with TiN, TiAIN, TiCN and Diamond coating. Shown RADII LEAD ANGLE INCLUDED ANGLE BACK CLEARANCE MODIFICATIONS SEE PAGE 8-3 FOR ADDITIONAL CUSTOM BLANK TOP RAKE (SIDE VIEW) CHIP BREAKER (SIDE VIEW) SIDE CLEARANCE (END VIEW) PG 8-6 ADAPTER STYLES TOOLHOLDER SELECTIONS PG 7-2 PG 7-2 PRODUCT DEMONSTRATION SPEEDS AND FEEDS APPLICATION REFERENCE TROUBLE SHOOTING TECHNICAL SECTIONS PG 9-15 PGS 9-3 & 9-4 PG
4 INTERNAL FACE GROOVING TOOLS E FRONT RAKE: Primary 10 BACK CLEARANCE: 2 ID side SIDE CLEARANCE: 2 ID side RADIUS: Sharp corner through full radius available TOP RAKE: 0 LEAD ANGLE: 0 Illustrated ORDERING INSTRUCTIONS Complete the ORDER CODE in the table below that represents your selection of groove width and tool dimensions. EXAMPLE: The ORDER CODE for a 1/4" major diameter, clockwise rotation tool with an.080" groove width,.125" depth of cut and.750" reach is: FT41C L Specify the Groove Width 'A' INTERNAL FACE GROOVING SPECIFICATIONS ORDER CODE Minimum Bore & Major Diameter Groove Width Range Depth of Cut Reach into Bore DURA-MAX 2000 Carbide See Page 9-15 for Speeds and Feeds Add-ons Use 'Order Code' and Add Overall Length Toolholder Page 7-2 'C' 'A' 'B' 'E' Full Radius ±.001" Page 8-3 Corner Radius Page 8-3 Coating Page 9-6 'D' Use Toolholders Beginning With 1/8".004"-.063".004"-.020" = 3 x 'A'.021"-.063" =.062".375" FT21C _ R FT21C _ L 1.365" + 'B' 'AD' 3/16".004"-.093".004"-.030" = 3 x 'A'.031"-.093" =.093".625" FT31C _ R FT31C _ L 1.865" + 'B' 'AD' 1/4".004"-.125" 5/16".004"-.156" 3/8".004"-.187".004"-.041" = 3 x 'A'.042"-.125" =.125".004"-.051" = 3 x 'A'.052"-.156" =.156".004"-.061" = 3 x 'A'.062"-.187" =.187".750" FT41C _ R FT41C _ L 2.365" + 'B' 'AD' add 'CR _' add 'FR' TiN add 'C' TiCN add 'D' 1.000" FT51C _ R FT51C _ L (indicate TiAlN size in add 'E'.xxx") 2.330" + 'B' 'AD' Diamond add 'F' 1.250" FT61C _ R FT61C _ L 2.800" + 'B' 'AD' 1/2".004"-.250".004"-.082" = 3 x 'A'.083"-.250" =.250" 1.750" FT81C _ R FT81C _ L 3.240" + 'B' 'AD' 2-4
5 U.S. PATENT NOS. 6,722,825 and 6,974,282 PRODUCT Internal face grooving and profiling for diameters of.415" and larger. Shank sizes 3/8", 1/2" and 5/8" in steel; 3/8" and 1/2" in heavy metal. 1/2" and 5/8" diameter toolholders are reversible for right and left hand orientation. Modifications can be provided on any of our tooling. Please contact us with your application requirements. Right in Right Toolholder Shown PRODUCT DEMONSTRATION SPEEDS AND FEEDS APPLICATION REFERENCE TROUBLE SHOOTING TECHNICAL SECTIONS PG 9-15 PGS 9-3 & 9-4 PG Right Illustrated FRONT RAKE: 15 BACK CLEARANCE: 2 both sides SIDE CLEARANCE: 2 I.D. side RADIUS: Sharp corner through full radius available TOP RAKE: 0 LEAD ANGLE: 0 SPECIFICATIONS ORDER CODE Orientation Width Depth of Cut Grades See Page 9-5 for expanded material descriptions and Page 9-10 or 9-12 for speeds and feeds information Add-ons Use 'Order Code' and Add 'A' 'B' DURA-MAX 2000 Carbide For Steel & ±.001" Interrupted Cutting DURA-MAX 5000 Carbide For Aluminum & Non-ferrous Full Radius Page 8-3 Corner Radius Page 8-3 Coating Page 9-6 Right For ID grooving use left hand 'MGT' Page 1-5 For face grooving use right hand 'MGTF' Page 2-6 Left For ID grooving use right hand 'MGT' Page "-.063".064"-.125".004"-.063".004"-.031" = 2 x 'A'.032"-.063" =.063".064"-.083" = 1.5 x 'A'.084"-.125" =.125".004"-.031" = 2 x 'A'.032"-.063" =.063" MGTI _D2R MGTI _D2L MGTI _D5R MGTI _D5L add 'FR' add 'CR _' (indicate size in.xxx") TiN add 'C' TiCN add 'D' TiAlN add 'E' Diamond add 'F' For face grooving use left hand 'MGTF' Page "-.125".064"-.083" = 1.5 x 'A'.084"-.125" =.125" 2-5
6 I.D. FACE GROOVING TOOLS C 1/2 MINI GROOVE N TURN MGTF12 THINBIT MADE IN U.S.A. A Right and Toolholder Illustrated Note: 1/2" and 5/8" toolholders are reversible for right hand or left hand orientation. For face grooving: Width Depth of Cut.004"-.031" 2 x width.032"-.063".063".064"-.083" 1.5 x width.084"-.125".125" I.D. FACE GROOVING ORDERING INSTRUCTIONS Select the ORDER CODE in the table below that represents your selection of tool specifications. EXAMPLE: The ORDER CODE for a.530" minimum bore and a 1/2" steel shank is: MGTF12 SPECIFICATIONS ORDER CODE Minimum Bore & Major Diameter Orientation & Toolholder Material Toolholder Package Includes Shank, Clamp and Hardware Replacement Parts Clamp Only Screw Only Shank Diameter Shank Length Wrench Only 'A' 'C' s Page 2-5 Use s Beginning With.415" Right Steel Right Heavy Metal Left Steel Left Heavy Metal MGTF38R 5.500" MGTF38RHM 5.875" 3/8" MGTF38L 5.500" MGTF38LHM MGC1 F31 W " 'MGTI' Use right hand inserts 'MGTI' Use left hand inserts.530" Steel MGTF12 1/2" Heavy Metal MGTF12HM 5.875".650" Steel MGTF58 5/8" 5.500" 5.500" 'MGTI' Use with left hand inserts for clockwise or with right hand inserts for counter-clockwise 2-6
7 U.S. PATENT NO. 5,638,728 PRODUCT Internal face grooving for diameters and larger with Depth of Cut to 1. Shank sizes 3/4 and 1. Modular tooling system will also accept OD & external face grooving heads. See compatibility guide on Page 9-8. If square shank is required, see Page 7-14, package styles S, T, U and V. Modifications can be provided on any of our tooling. Please contact us with your application requirements. Package N Shown INSERT STYLES INSERT SELECTIONS SEE PAGE 6-1 PRODUCT DEMONSTRATION SPEEDS AND FEEDS APPLICATION REFERENCE TROUBLE SHOOTING TECHNICAL SECTIONS PG 9-12 PGS 9-3 & 9-4 PG PACKAGE STYLE M - Left Shank, Chuck Top View Tools shown cutting edge up. N - Right Shank, Note: If square shank is required, see Page 7-14, package styles S, T, U and V. 2-7
8 I.D. FACE GROOVING TOOLS ORDERING INSTRUCTIONS Complete the ORDER CODE in the table below that represents your selection of major diameter. EXAMPLE: The ORDER CODE for a 3mm insert width, toolholder package style 'N' with a.500" depth of cut, 1" shank and 1.75" major diameter is: DGPN Specify Major Diameter 'CODE' here I.D. FACE GROOVING SPECIFICATIONS Width Depth of Cut Package Style Toolholder Package Includes Shank, Head, Clamp and Hardware ORDER CODE s Replacement Parts 3/4" Shank 7" Long 1" Shank 7" Long Use s Beginning With Head Head Hardware Shank 34 = 3/4" 01 = 1" Clamp Clamp Hardware 2mm (.078") M DGPM DGPM 'DGI2' DGH52013 DGS ZL DGC52013 N DGPN DGPN (Page 6-1) DGH62013 DGS ZR DGC mm (.118") M DGPM DGPM 'DGI3' DGH53013 DGS ZL DGC53013 N DGPN DGPN (Page 6-1) DGH63013 DGS ZR DGC mm (.157") 20mm (3/4") M DGPM DGPM DGH54013 DGS ZL DGC54013 N DGPN DGPN 'DGI4' DGH64013 DGS ZR DGC64013 M N DGPM DGPM DGPN DGPN (Page 6-1) DGH54020 DGH64020 Screw: 2 each S7552 DGS ZL DGC54020 DGS ZR DGC64020 Screw: S6552 5mm (.197") 25mm (1") M N DGPM DGPM DGPN DGPN 'DGI5' DGH55013 DGH65013 Wrench: W4025 DGS ZL DGC55013 DGS ZR DGC65013 M DGPM DGPM (Page 6-1) DGH55025 DGS ZL DGC55025 N DGPN DGPN DGH65025 DGS ZR DGC65025 Wrench: W4025 6mm (.236") 25mm (1") M DGPM DGPM DGH56013 DGS ZL DGC56013 N M DGPN DGPN DGPM DGPM 'DGI6' (Page 6-1) DGH66013 DGH56025 DGS ZR DGC66013 DGS ZL DGC56025 N DGPN DGPN DGH66025 DGS ZR DGC66025 Major Diameter Range Code 1.574"-1.968" (40-50mm) "-2.362" (50-60mm) "-2.952" (60-75mm) "-3.937" (75-100mm) "-5.905" ( mm) " " ( mm) "- (300mm- ) 30 Note: As long as first plunge is made within major diameter range and each following plunge overlaps, groove width can be increased toward or away from center of part. 2-8
9 U.S. PATENT NOS. 6,688,816 and 6,824,333 INSERTS PRODUCT Face grooving for major diameters.300",.750", 1.250", 3" and greater. Face grooving with a central hub or flat face..004" -.150" in.001" increments available. Sub-micron grain DURA-MAX 2000 and 5000 Carbides. s available with TiN, TiAIN, TiCN and Diamond coating. Left, in Left, Straight Toolholder Shown RADII DEPTH OF CUT SIZING BACK CLEARANCE MODIFICATIONS SEE PAGES 8-2 & 8-3 FOR ADDITIONAL LEAD ANGLE TOP RAKE (SIDE VIEW) CHIP BREAKER (SIDE VIEW) SIDE CLEARANCE (END VIEW) CNC, SWISS, CONVENTIONAL STYLE ROUND STYLE THINBIT KAISER TOOL MADE IN U.S.A. 3/4" GROOVE THINBIT MADE IN U.S.A. KAISER TOOL CO 1" ROUND REVER THINBIT TOOLHOLDER PG 7-3 PG 7-4 PG 7-7 PG 7-8 SELECTIONS 45º STYLE SWISS FACE STYLE PG 7-11 PG 7-6 PRODUCT DEMONSTRATION SPEEDS AND FEEDS APPLICATION REFERENCE TROUBLE SHOOTING TECHNICAL SECTIONS PG 9-12 PGS 9-3 & 9-4 PG
10 FACE GROOVING INSERTS.820".145".240" Left, Illustrated ORDERING INSTRUCTIONS FRONT RAKE: Primary 10 honed, Secondary 15 BACK CLEARANCE: 2-1/2 both sides SIDE CLEARANCE:.004" -.019" - 0 ID side.020" -.150" - 5 ID side RADIUS: Sharp corner through full radius available TOP RAKE: 0 LEAD ANGLE: 0 INSERTS FACE GROOVING Complete the ORDER CODE in the table below that represents your selection of groove width and insert grade. EXAMPLE: The ORDER CODE for a left hand/counter-clockwise,.100" wide insert in DURA-MAX 2000, with a.750" major diameter and no corner radius is: LGTF D27504 Specify the Width 'A' SPECIFICATIONS ORDER CODE INFO. Orientation Width Depth of Cut Major Diameter Grades See Page 9-5 for expanded material descriptions and Page 9-12 for Speeds and Feeds information Add-ons Use 'Order Code' and Add Toolholder Catalog Section 7 'A' ±.001" 'B' Can be used on any diameter equal to or greater than listed DURA-MAX 2000 Carbide For Steel & Interrupted Cutting DURA-MAX 5000 Carbide For Aluminum & Non-ferrous Full Radius Page 8-3 Corner Radius Page 8-3 Coating Page 9-6 Use Toolholders Beginning With Left /.004" -.150" Width D.O.C..004"-.033" = 3 x 'A'.034"-.039" =.100".040"-.100" = 2.5 x 'A'.101"-.150" =.250".300" LGTF _ D23004 LGTF _ D " LGTF _ D27504 LGTF _ D " LGTF _ D LGTF _ D * 3.000" LGT _ D2L LGT _ D5L add 'FR' add 'CR _' (indicate size in.xxx") TiN add 'C' TiCN add 'D' TiAlN add 'E' Diamond add 'F' 'L' Use left hand straight holder or right hand 90º holder * 3.000" Major Diameter Excludes.004" -.019" Width Due to Side Clearance 2-10
11 U.S. PATENT NOS. 6,688, and 6,824,333 INSERTS PRODUCT For Dovetail O-Ring face grooving. Groove Widths.030,.050,.070,.090,.100,.125 &.150. Major diameters from.300. Sub-micron grain DURA-MAX 2000 and 5000 Carbides. s available with TiN, TiCN, TiAIN or Diamond Film Coating. Style 5 in Right, 90 Toolholder Shown RADII DEPTH OF CUT SIZING BACK CLEARANCE MODIFICATIONS SEE PAGES 8-2 & 8-3 FOR ADDITIONAL LEAD ANGLE TOP RAKE (SIDE VIEW) CHIP BREAKER (SIDE VIEW) SIDE CLEARANCE (END VIEW) CNC, SWISS, CONVENTIONAL STYLE ROUND STYLE THINBIT KAISER TOOL MADE IN U.S.A. 3/4" GROOVE THINBIT MADE IN U.S.A. KAISER TOOL CO 1" ROUND REVER THINBIT TOOLHOLDER PG 7-3 PG 7-4 PG 7-7 PG 7-8 SELECTIONS 45º STYLE SWISS FACE STYLE PG 7-11 PG 7-6 PRODUCT DEMONSTRATION SPEEDS AND FEEDS APPLICATION REFERENCE TROUBLE SHOOTING TECHNICAL SECTIONS PG 9-12 PGS 9-3 & 9-4 PG
12 DOVETAIL O-RING FACE GROOVING INSERTS FRONT RAKE: Primary 10 honed, Secondary 15 " BACK CLEARANCE: 24 one side " " SIDE CLEARANCE: Depends on major diameter RADIUS: One side as specified TOP RAKE: 0 LEAD ANGLE: 0 Back Clearance: 24 Style 6 Shown ORDERING INSTRUCTIONS Note: For best performance, form undercut by profiling. Select the ORDER CODE in the table below that represents your selection of groove width and insert grade. EXAMPLE: The ORDER CODE for a left hand/counter-clockwise,.100" wide OD side insert in DURA-MAX 2000, with a.300" major diameter and a.030" corner radius is: LGDT100D23006CR030 DOVE TAIL FACE GROOVING SPECIFICATIONS ORDER CODE INFO. Orientation & Radius Width Depth of Cut Major Diameter Grades See Page 9-5 for expanded material descriptions and Page 9-12 for Speeds and Feeds information Add-ons Use 'Order Code' and Add Toolholder Catalog Section 7 'A' ±.001" 'B' Can be used on any diameter equal to or greater than listed DURA-MAX 2000 Carbide For Steel & Interrupted Cutting ID Tool Style 5 OD Tool Style 6 DURA-MAX 5000 Carbide For Aluminum & Non-ferrous ID Tool Style 5 OD Tool Style 6 Coating Page 9-6 Use Toolholders Beginning With.300" LGDT030D23005CR015 LGDT030D23006CR015 LGDT030D53005CR015 LGDT030D53006CR ".030".500" LGDT030D25005CR015 LGDT030D25006CR015 LGDT030D55005CR015 LGDT030D55006CR " LGDT030D210005CR015 LGDT030D210006CR015 LGDT030D510005CR015 LGDT030D510006CR " LGDT050D23005CR015 LGDT050D23006CR015 LGDT050D53005CR015 LGDT050D53006CR015 Left / ;.015" Radius Left / ;.030" Radius.050".070".070".100".090".115".100".125".125".190".150".200".500" LGDT050D25005CR015 LGDT050D25006CR015 LGDT050D55005CR015 LGDT050D55006CR " LGDT050D210005CR015 LGDT050D210006CR015 LGDT050D510005CR015 LGDT050D510006CR " LGDT070D23005CR015 LGDT070D23006CR015 LGDT070D53005CR015 LGDT070D53006CR " LGDT070D25005CR015 LGDT070D25006CR015 LGDT070D55005CR015 LGDT070D55006CR " LGDT070D210005CR015 LGDT070D210006CR015 LGDT070D510005CR015 LGDT070D510006CR " LGDT090D23005CR015 LGDT090D23006CR015 LGDT090D53005CR015 LGDT090D53006CR " LGDT090D25005CR015 LGDT090D25006CR015 LGDT090D55005CR015 LGDT090D55006CR " LGDT090D210005CR015 LGDT090D210006CR015 LGDT090D510005CR015 LGDT090D510006CR " LGDT100D23005CR030 LGDT100D23006CR030 LGDT100D53005CR030 LGDT100D53006CR " LGDT100D210005CR030 LGDT100D210006CR030 LGDT100D510005CR030 LGDT100D510006CR " LGDT125D23005CR030 LGDT125D23006CR030 LGDT125D53005CR030 LGDT125D53006CR " LGDT125D210005CR030 LGDT125D210006CR030 LGDT125D510005CR030 LGDT125D510006CR " LGDT150D210005CR030 LGDT150D210006CR030 LGDT150D510005CR030 LGDT150D510006CR " LGDT150D220005CR030 LGDT150D220006CR030 LGDT150D520005CR030 LGDT150D520006CR030 TiN add 'C' TiCN add 'D' TiAlN add 'E' Diamond add 'F' 'L' 2-12
13 U.S. PATENT NOS. 6,688,816 and 6,824,333 INSERTS PRODUCT For Static O-Ring Face Grooving. Groove widths.086",.103",.122",.125" &.138" 7 included angle. Major diameters starting from.300". Sub-micron grain DURA-MAX 2000 and 5000 Carbides. s available with TiN, TiCN, TiAIN or Diamond film coating. and Right, 90 Toolholder Shown RADII DEPTH OF CUT SIZING BACK CLEARANCE MODIFICATIONS SEE PAGES 8-2 & 8-3 FOR ADDITIONAL LEAD ANGLE TOP RAKE (SIDE VIEW) CHIP BREAKER (SIDE VIEW) SIDE CLEARANCE (END VIEW) CNC, SWISS, CONVENTIONAL STYLE ROUND STYLE THINBIT KAISER TOOL MADE IN U.S.A. 3/4" GROOVE THINBIT MADE IN U.S.A. KAISER TOOL CO 1" ROUND REVER THINBIT TOOLHOLDER PG 7-3 PG 7-4 PG 7-7 PG 7-8 SELECTIONS 45º STYLE SWISS FACE STYLE PG 7-12 PG 7-6 PRODUCT DEMONSTRATION SPEEDS AND FEEDS APPLICATION REFERENCE TROUBLE SHOOTING TECHNICAL SECTIONS PG 9-12 PGS 9-3 & 9-4 PG
14 STATIC O-RING FACE GROOVING INSERTS FRONT RAKE: Primary 10 honed, Secondary 15 BACK CLEARANCE: 7 included angle SIDE CLEARANCE: 5 both sides RADIUS:.010" or.020" TOP RAKE: 0 LEAD ANGLE: 0 DEPTH OF CUT:.170" or.250" ORDERING INSTRUCTIONS Select the ORDER CODE in the table below that represents your selection of groove width and insert grade. EXAMPLE: The ORDER CODE for a counter-clockwise,.138" wide insert in DURA-MAX 2000, with a.750" major diameter and a.010" corner radius is: LGORF138D27508CR010 STATIC O-RING FACE GROOVING SPECIFICATIONS ORDER CODE INFO. Orientation & Radius Width Depth of Cut Major Diameter Grades See Page 9-5 for expanded material descriptions and Page 9-12 for Speeds and Feeds information Add-ons Use 'Order Code' and Add Toolholder Catalog Section 7 'A' 'B' Can be used on any diameter ±.001" equal to or greater than listed DURA-MAX 2000 Carbide For Steel & Interrupted Cutting DURA-MAX 5000 Carbide For Aluminum & Non-ferrous Coating Page 9-6 Use Toolholders Beginning With.086".250".300" LGORF086D23008CR010 LGORF086D53008CR " LGORF086D27508CR010 LGORF086D57508CR010 ;.010" Corner Radius.103".250".122".250".138".170".300" LGORF103D23008CR010 LGORF103D53008CR " LGORF103D27508CR010 LGORF103D57508CR " LGORF122D23008CR010 LGORF122D53008CR " LGORF122D27508CR010 LGORF122D57508CR " LGORF138D23008CR010 LGORF138D53008CR " LGORF138D27508CR010 LGORF138D57508CR010 TiN add 'C' TiCN add 'D' TiAlN add 'E' Diamond add 'F' 'L' Use left hand straight holder or right hand 90 holder ;.020" Corner Radius.125".250".300" LGORF125D23008CR020 LGORF125D53008CR " LGORF125D27508CR020 LGORF125D57508CR
15 U.S. PATENT NO. 5,638,728 PRODUCT External face grooving with Depth of Cut to 1. Shank sizes 3/4, 1, 16mm, 20mm and 25mm in straight and 90º orientations. Modular tooling system will also accept OD & internal face grooving heads. See compatibility guide on Page 9-8. If round shanks are required, see Page 7-13, package styles O and P. Modifications can be provided on any of our tooling. Please contact us with your application requirements. Package D Shown STYLES INSERT SELECTIONS SEE PAGE 6-1 PRODUCT DEMONSTRATION SPEEDS AND FEEDS APPLICATION REFERENCE TROUBLE SHOOTING TECHNICAL SECTIONS PG 9-12 PGS 9-3 & 9-4 PG ORDERING INSTRUCTIONS 3/4, 1 and Metric Shanks Select the ORDER CODE in the table at right that represents your selection of major diameter. EXAMPLE: The ORDER CODE for a 3mm insert width, toolholder package style C with a.500 Depth of Cut, 1 shank and 1 major diameter is: DGPC Specify the SHANK SIZE and MAJOR DIAMETER CODE PACKAGE STYLE A - Left, 90º Shank, B - Right, Straight Shank, Chuck Top View Tools shown cutting edge up. C - Left, Straight Shank, D - Right, 90º Shank, Note: If round shanks are required, see Page 7-13, package styles "O" and "P". 2-15
16 FACE GROOVING TOOLS SPECIFICATIONS ORDER CODE Width Depth Package of Cut Style See Page /4" Shank 3/4"x3/4"x5" Toolholder Package Includes Shank, Head, Clamp and Hardware 1" Shank 1"x1"x5" Metric Shanks 16 = 16x16x125mm 20 = 20x1"x125mm 25 = 25x1"x125mm s Section 6 Use s Beginning With Head Replacement Parts Head Hardware Shank 34 = 3/4" 01 = 1" 16 = 16mm 20 = 20mm 25 = 25mm Clamp Clamp Hardware 2mm (.078") 3mm (.118") A DGPA DGPA DGPA2013 DGS YL B DGPB DGPB DGPB2013 'DGI2' DGH32013 DGS XR C DGPC DGPC DGPC2013 (Page 6-1) DGH42013 DGS XL D DGPD DGPD DGPD2013 DGS YR A Use 'DGMI3' DGPA DGPA DGPA3013 DGS YL for major diameter DGH33013 B DGPB DGPB DGPB3013 codes '02'&'25' DGS XR C DGPC DGPC DGPC3013 'DGI3' for all DGS XL others DGH43013 D DGPD DGPD DGPD3013 (Page 6-1) DGS YR DGC12013 DGC22013 DGC13013 DGC23013 DEEPGROOVE FACE GROOVING 4mm (.157") 5mm (.197") 20mm (3/4") 25mm (1") A DGPA DGPA DGPA4013 DGS YL DGH34013 B DGPB DGPB DGPB4013 Use 'DGMI4' DGS XR for major C DGPC DGPC DGPC4013 diameter DGS XL DGH44013 D DGPD DGPD DGPD4013 codes DGS YR '02'&'25' A DGPA DGPA DGPA4020 'DGI4' for all DGS YL DGH34020 B DGPB DGPB DGPB4020 others Screw: DGS XR 2 each C D A DGPC DGPC DGPC4020 DGPD DGPD DGPD4020 DGPA DGPA DGPA5013 (Page 6-1) DGH44020 DGH35013 S7552 Wrench: W4025 DGS XL DGS YR DGS YL B DGPB DGPB DGPB5013 DGS XR C DGPC DGPC DGPC5013 DGS XL D DGPD DGPD DGPD5013 'DGI5' DGH45013 DGS YR A DGPA DGPA DGPA5025 (Page 6-1) DGH35025 DGS YL B DGPB DGPB DGPB5025 DGS XR C DGPC DGPC DGPC5025 DGH45025 DGS XL D DGPD DGPD DGPD5025 DGS YR DGC14013 DGC24013 DGC14020 DGC24020 DGC15013 DGC25013 DGC15025 DGC25025 Screw: S6552 Wrench: W4025 6mm (.236") 25mm (1") A DGPA DGPA DGPA6013 DGS YL DGH36013 DGC16013 B DGPB DGPB DGPB6013 DGS XR C DGPC DGPC DGPC6013 DGS XL D DGPD DGPD DGPD6013 'DGI6' DGH46013 DGS YR DGC26013 A DGPA DGPA DGPA6025 (Page 6-1) DGH36025 DGS YL DGC16025 B DGPB DGPB DGPB6025 DGS XR C DGPC DGPC DGPC6025 DGH46025 DGS XL DGC26025 D DGPD DGPD DGPD6025 DGS YR Shank Major Diameter Range.787"-.885" ( mm).885"-.984" ( mm).984"-1.082" ( mm) 1.082"-1.181" ( mm) 1.181"-1.377" (30-35mm) Width Code Style Major Diameter Range Width Code Style 2mm 02 DGI 2mm 50 DGI 1.377"-1.574" (35-40mm) 3 & 4mm 02 DGMI 3, 4, 5 & 6mm 34 DGI 2mm 25 DGI 1.574"-1.968" (40-50mm) 45 DGI 3 & 4mm 25 DGMI 1.968"-2.362" (50-60mm) 56 DGI 2mm 57 DGI 2.362"-2.952" (60-75mm) 67 DGI 3, 4, 5 & 6mm 23 DGI 2.952"-3.937" (75-100mm) All 71 DGI 2mm 70 DGI 3.937"-5.905" ( mm) 11 DGI 3, 4, 5 & 6mm 23 DGI 5.905" " ( mm) 13 DGI 2mm 05 DGI "- (300mm- ) 30 DGI 3, 4, 5 & 6mm 34 DGI Major Diameter Code Note: As long as first plunge is made within major diameter range and each following plunge overlaps, groove width can be increased toward or away from center of part. 2-16
Grooving Threading Parting Boring Turning Face Grooving Custom Tooling Form Tools. thinbit.com
Grooving Threading Parting Boring Turning Face Grooving Custom Tooling Form Tools 2014 thinbit.com SECTION 1: GROOVING PG 1-9 GROOVING AND TURNING.004 THROUGH.150 IN.001 INCREMENTS PG 1-13 1.000 DEPTH
AMERICAN QUALITY AMERICAN VALUE AMERICAN PRIDE
AMERICAN QUALITY AMERICAN VALUE AMERICAN PRIDE FEATURING OVER 48 YEARS OF COMPLETE TOOLING SOLUTIONS FOR GROOVING THREADING PARTING BORING TURNING FACE GROOVING SPECIALS FORM TOOLS MADE IN THE U.S.A. SINCE
888 THINBIT 888 THINFAX THINBIT.COM
SINCE 1964 888 THINBIT 888 THINFAX THINBIT.COM GROOVING THREADING PARTING BORING TURNING FACE GROOVING CUSTOM TOOLING FORM TOOLING MILL TOOLING 2018 thinbit.com MADE IN THE USA SECTION 1: GROOVING PG 1-9
Page 1-7 Page º(+) TOP RAKE (SIDE VIEW) APPLICATION REFERENCE PGS 9-10, 9-12, 9-18 & 9-20 ORDERING INSTRUCTIONS
U.S. PATENT N. 5,638,728 PRDUCT INFRMATIN 2, 3, 4, 5 and 6mm insert widths. Recessed pocket and raised edge for chip control. Internal grooving, external grooving, face grooving and parting. Sub-micron
O.D./I.D. GROOVING AND TURNING INSERTS .145" .240" ORDERING INSTRUCTIONS
O.D./I.D. GROOVING ND TURNING INSERTS FRONT RKE: CRIDE: Primary 10 honed, Secondary 15 HIGH SPEED STEEL: 15 CK CLERNCE: 2-1/2 both sides SIDE CLERNCE:.004" -.019" - 0 both sides.020" -.150" - 5 both sides
U.S. PATENT NOS. 6,688,816 and 6,824,333 INSERT WIDTH TOP RAKE (SIDE VIEW) APPLICATION REFERENCE PG 9-20
U.S. PTENT NOS. 6,688,816 and 6,824,333 SERTS.025",.045",.062",.085" and.115" Parting off up to 1" diameter 0 or 7 lead angle Centered or Offset Sub-micron grain DUR-MX 2000 and 5000 s and High Speed Steel.
APPLICATION REFERENCE
O.D./I.D. S Insert Shown in Right Hand Toolholder D THINIT LGI093D2.240" +.0 -.0 FRONT RKE: RIDE: Primary 10 honed, Secondary 15 HIGH SPEED STEEL: 15 K LERNE: 2-1/2 both sides SIDE LERNE: 0 both sides
PRODUCT SELECTION GUIDE - TOOLHOLDERS ADAPTERS
PRODUT SELETION GUIDE - TOOLHOLDERS www.thinbit.com/qr7-1 Scan this code for additional information. DPTERS dapters Square and round adapters Use for boring bars and solid carbide tooling THINIT ROUND
Mission Statement. 2005, Manchester Tool Company. All rights reserved.
Mission Statement Manchester Tool Company shall provide tooling systems to the metal cutting and similar industries, specializing in cutoff, grooving and complimentary niche products. We are dedicated
KAISER TOOL COMPANY, INC.
U.S. PTENT NOS. 6,688,816 and 6,824,333 S External threading within.070" of a shoulder. Internal ME threading with 1.250" minimum bore diameter. 4 threads per inch and greater. Sub-micron grain DUR-MX
KAISER TOOL COMPANY, INC.
SERTS External grooving. Internal Static O-Ring grooving with 1.250" minimum bore diameter. Sub-micron grain DUR-MX 2000 and 5000 arbides. Inserts available with TiN, Ti, TiN and Diamond coating. Insert
APPLICATION REFERENCE
O.D./I.D. GROOVING INSERTS Insert Shown in D THINIT LGI093D2.240" +.0 -.0 FRONT RKE: RIDE: Primary 10 honed, Secondary 15 HIGH SPEED STEEL: 15 K LERNE: 2-1/2 both sides SIDE LERNE: 0 both sides RDIUS:
KAISER TOOL COMPANY, INC.
O.D./I.D. THREDING INSERTS D FRONT RKE: 15 RDIUS:.002" or.000" TOP RKE: 0 PROFILE: 60 Insert Shown in Toolholder PRODUT INFORMTION External threading within.046" of a shoulder. Internal threading with
Lathe Accessories. Work-holding, -supporting, and driving devices
46-1 Lathe Accessories Divided into two categories Work-holding, -supporting, and driving devices Lathe centers, chucks, faceplates Mandrels, steady and follower rests Lathe dogs, drive plates Cutting-tool-holding
with better tools from Introducing: Dapra's New Modular Heads Designed to Screw On to Industry Standard Systems
CUTTING Times Vol. 4, Issue 1 with better tools from Dapra Corporation 66 Granby Street, Bloomfield, CT 06002 1-800-243-3344 860-242-8539 Fax 860-242-3017 Email info@dapra.com www.dapra.com Introducing:
Hertel Indexable Drills (HID)
Hertel Indexable Drills (HID) mscdirect.com/hertel DESIGNED TO DELIVER Hertel cutting tools are designed to deliver consistency, reliability, durability and value with every cut. For over 65 years, Hertel
PARTING ISCAR PARTING USER GUIDE. Parting and Grooving. Insert Positioning
90 80 0 70 10 60 20 50 30 40 Parting and Grooving Selection of Inserts For a proper match of insert and cutting material to application, the following variables must be taken into consideration: Width
New. Products2013.
T u n g a l o y www.tungaloy.com Company Overview Providing Complete Tooling Solutions for the Metal Removal and Industrial Product Sectors TUNGALOY is one of the world s leading manufacturers of carbide
SINGLE POINT TOOLS. Mini Boring Bars Mini Boring Bars come in a range of diameters from to inch. They are fluted for maximum strength.
SINGLE POINT TOOLS All single point tools are designed for internal machining on a lathe. The helical boring bars can be used for both lathe and mill applications. All cutting tools are made from premium
External Turning. Outline Review of Turning. Cutters for Turning Centers
Outline Review of Turning External Turning 3 External Turning Parameters Cutting Tools Inserts Toolholders Machining Operations Roughing Finishing General Recommendations Turning Calculations Machining
Optimized flute design Better chip evacuation. Carbide substrate Higher heat resistance, higher speed.
Thread Mills Available for the first time, our solid thread mills are designed to be the highest quality thread milling solution. WIDIA-GTD Cut up to 63 HRC. Improved overall thread quality. Optimized
Features. High Positive Rake Angle. Multi-Side Grinding. High Speed, High Feed Rate. Economical
Engraving This is a revolutionary new concept of engraving tools with indexable carbide inserts. They offer you the ability to produce HIGH QUAITY ENGRAVING in most materials. The latest coated carbide
Cutting Tools Overview #2 - Turning
Cutting Tools Overview #2 - Turning Last month's column was an overview of some of the different types of tools used in the milling process. This month we are going to discuss some of the most common cutting
Value-Added Programs. Refurbishment Service. Refurbishment Delivery Service. Just In Time Inventory Programs. Commodity Management
Value-Added Programs ClappDiCO offers a number of value-added programs that reduces our customers manufacturing costs on a per unit basis. Refurbishment Service A complete refurbishment service to restore
Carbide Reamers...P18. Ejector Pin Counter Bores...P17
P1 Carbide Reamers...P18 Ejector Pin Counter Bores...P17 Extended Reach 2 Flute End Mills (For Machining Aluminum) Ball Nose...P15 Square End...P16 Extended Reach 4 Flute Coated End Mills Ball Nose...P11
Chapter 23 Drilling and Hole Making Processes. Materials Processing. Hole Making Processes. MET Manufacturing Processes
MET 33800 Manufacturing Processes Chapter 23 Drilling and Hole Making Processes Before you begin: Turn on the sound on your computer. There is audio to accompany this presentation. Materials Processing
Technical T-A & GEN2 T-A GEN3SYS APX. Revolution & Core Drill. ASC 320 Solid Carbide. AccuPort 432. Page CONTENTS. Set-up Instructions 256
Technical ASC 0 Solid Carbide CONTENTS Page Set-up Instructions 6 AccuPort 4 Recommended Speeds & Feeds 60 Guaranteed Application Request Form 99 +44 (0)84 400 900 +44 (0)84 400 0 enquiries@alliedmaxcut.com
solid carbide tools 100% cnc manufactured in the usa
solid carbide tools 100% cnc manufactured in the usa V w isi w t w ou. C dura r w at m eb 20 al ill si 09 og.co te m Maximum Performance End Mills Series Product Page# WK-3-R WK-3 WK-3-ER WK-BN-3 WK-4-R
Everything for metal Machining Under one Roof M I R C O N A
IUT 0058E Everything for metal Machining Under one Roof M I R C O N A MIRCONA is a Swedish company with its head office situated in the town of Gävle, Sweden. The main activity of the company since it
INDEXABLE BORING BAR AND INSERTS FLAT TOP, CHIP CONTROL, CBN, AND PCD
INDEXABLE BORING BAR AND S FLAT TOP, CHIP CONTROL,, AND 80 Diamond.156 IC R.156.040 80 DIAMOND FLAT TOP 80 DIAMOND CHIP CONTROL AT6+ 0.003 ACD5031 ACD5031E AT6+ 0.007 ACD5071 ACD5071E AT6+ 0.015 ACD5151
BSF. Large Ratio Automatic Back Counterboring & Spotfacing Tool
BSF Large Ratio Automatic Back Counterboring & Spotfacing Tool Counterbores up to 2.3xd Replaceable carbide coated blades for extended life Very simple to use Suitable for CNC machines with through coolant
Cutting Tools DIGEST Catalog
Cutting Tools DIGEST Catalog Insert Grade CVD Coating Innovation CA5 series Ultra fine interface increases adhesion strength to provide long tool life and stable machining High aspect ratio of α-al 2 O
DRA DRA. MagicDrill. High Efficiency Modular Drill. Excellent hole accuracy with a low cutting force design. High Efficiency Modular Drill
High Efficiency Modular Drill High Efficiency Modular Drill MagicDrill DRA Excellent hole accuracy with a low cutting force design Optimal web thickness limits deflection Fine chip breaking and smooth
CARBIDE END MILLS SPECIFICATIONS
SPECIFICATIONS COATING GUIDE Material Hardness TiN TiCN TiALN Austentic Stainless Steel < 35 HRc * X Martinistic Stainless Steel < 35 HRc * X Martinistic Stainless Steel >= 35 HRc X PH Stainless Steel
Broaching, External External Broach Tool Holders...18 Driven Broach Tool Holder for Multi's External Broaches...19
TABLE OF CONTENTS CATALOG 2017 TITLE PAGE Broaching, Internal Swiss Adjustment Free Broach Tool Holders...8 Swiss Broaching Heads for ER Collet Chucks...7 Adjustable Broach Tool Holders...10 CNC Adj. Free
COFA. Deburring Tool for Elliptical or Contoured Surfaces. increased performance. from stock
Deburring Tool for Elliptical or Contoured Surfaces increased performance from stock Cat. No. HTC015 Introduction Catalog HTC015No. HTC14 The HEULE COFA deburring tool removes burrs from the front and
Broaching, External External Broach Tool Holders...18 Driven Broach Tool Holder for Multi's External Broaches...19
TABLE OF CONTENTS CATALOG 2017 TITLE PAGE Broaching, Internal Swiss Adjustment Free Broach Tool Holders...8 Swiss Broaching Heads for ER Collet Chucks...7 Adjustable Broach Tool Holders...10 CNC Adj. Free
UPDATE. NEW Gold-QuadF 09 09mm IC Insert Sizes
Styles: End Mill 15G1F Face Mill 5G5F, 5G6F s: 1.000" - 3.000" Inserts: SDXS0904MPR-MM SDXS0904MPR-MR SDXS0904MPR-MR1 Grades: IN4004 IN4005 IN4030 IN4035 UPDATE NEW Gold-QuadF 09 09mm IC Insert Sizes Features
323 and 365 Series SmoothFlute Variable Helix End Mills
323 and 365 Series SmoothFlute Variable Helix End Mills 323-365 High Speed Machining / HSM as well as traditional milling. Designed for advanced tool path software. Variable Helix where the helix changes
NO NEED TO CHOOSE NINE9 DOES IT ALL!
NO NEED TO CHOOSE NINE9 DOES IT ALL! Cat. No. 11.a NC Spot Drills Corner Rounding Cutters & Engraving Tools Various applications of NC Spot Drill We Focus: Higher efficiency Position accuracy Long tool
Lower Spindle Power Consumptionn
ower Spindle Power Consumptionn > Five cutters for drilling Ø13~Ø50 mm. > One insert for all kind of materials. > The drilling is done by helical interpolation. (circular ramping milling) Nine9 NC Helix
APRIL 2009 / NEW-100 / PAGE 1 OF 13
APRIL 2009 / NEW-100 / PAGE 1 OF 13 The standard UNIDEX line covers reaming applications from 5/16 to 1 1/4 diameter. The single indexable blade and high wear resistant carbide or cermet pads provide a
Features. High Positive Rake Angle. Multi-Side Grinding. High Speed, High Feed Rate. Economical
Engraving This is a revolutionary new concept of engraving tools with indexable carbide inserts. They offer you the ability to produce HIGH QUAITY ENGRAVING in most materials. The latest coated carbide
BUY 1 Toolholder and 1 Cartridge. and GET 10 FREE INSERTS! up to $ value. Built for Productivity!
KOOL Cut MODULAR Turning & Grooving System BUY 1 Toolholder and 1 Cartridge 10 FREE INSERTS! up to $229.40 value TM KOOL Cut TM Modular Turning & Grooving Built for Productivity! Interchangeable s & Cartridges
MACHINING PROCESSES: TURNING AND HOLE MAKING. Dr. Mohammad Abuhaiba 1
MACHINING PROCESSES: TURNING AND HOLE MAKING Dr. Mohammad Abuhaiba 1 HoweWork Assignment Due Wensday 7/7/2010 1. Estimate the machining time required to rough cut a 0.5 m long annealed copper alloy round
Save Scrap, Time and Money
COMPACT RIGID CUTOFF HOLDER wks with most all pick off and back finish attachments Quickchange Carbide Insert by Manchester Tools Multiple Designs f Flexibility Save Scrap, Time and Money Benefits of New
Jet-Stream Modular Carbide & Steel Boring Bar Instructions Manual
Workpiece Rigidity 1 Work holding Use the proper chuck and jaws to hold the work-piece, to assure that the part is held with maximum rigidity and stability under cutting force. 2 Steady Rest Support When
Lecture 18. Chapter 24 Milling, Sawing, and Filing; Gear Manufacturing (cont.) Planing
Lecture 18 Chapter 24 Milling, Sawing, and Filing; Gear Manufacturing (cont.) Planing For production of: Flat surfaces Grooves Notches Performed on long (on average 10 m) workpieces Workpiece moves / Tool
AUTOMATED MACHINE TOOLS & CUTTING TOOLS
CAD/CAM COURSE TOPIC OF DISCUSSION AUTOMATED MACHINE TOOLS & CUTTING TOOLS 1 CNC systems are used in a number of manufacturing processes including machining, forming, and fabrication Forming & fabrication
ARNO (UK) Limited We have a passion for precision. Holder 1 see page 3. Holder 35. Holders 70 see page 4. see page 5. Save Over 30% see page 8-10
Promotions - 2017 ARNO (UK) Limited NC - Grooving System The flexible solution for both axial and radial grooving SA Part-Off System With or without through tool coolant see page 2 Holder 1 see page 3
Flexible tool overhang lengths possible by combining the modular extension arbor and shank with insert run-out adjustment mechanism
Sumi Easy insert replacement Characteristics Achieves efficiency through high speed, high feeding ability!! (v c =50 to 500m/min, f = 0.4 to 1.2mm/rev) Compatibility with a wide range of cutting conditions
Broaching, External External Broach Tool Holders...18 Driven Broach Tool Holder for Multi's External Broaches...19
TABLE OF CONTENTS CATALOG 2017 TITLE PAGE Broaching, Internal Swiss Adjustment Free Broach Tool Holders...8 Swiss Broaching Heads for ER Collet Chucks...7 Adjustable Broach Tool Holders...10 CNC Adj. Free
A very warm welcome (Arial, 24-point bold font) Discover what's under the surface (Arial, 20-point bold font in italics)
A very warm welcome (Arial, 24-point bold font) Discover what's under the surface (Arial, 20-point bold font in italics) HORN Technology Days 2015 Longitudinal turning Flexibly producing complex turned
Quick Change Carbide & Steel Boring Bar Instructions Manual
Workpiece Rigidity 1 Work holding Use the proper chuck and jaws to hold the work-piece, to assure that the part is held with maximum rigidity and stability under cutting force. 2 Steady Rest Support When
NC Spot Drill with Patented indexable carbide insert.
with Patented indexable carbide insert. High Efficiency! Low Cost! CNC Lathes, CNC Turning Centers and Machining Centers. One tool will perform multiple applications. Long tool life. Each insert has four
Plus Our NEW Quick Delivery Step Drill Program
LE ADING SOLUTIONS FOR CHAMFERED / THRE ADED HOLES Plus Our Quick Delivery Step Drill Program CHAMFERED / THREADED HOLE SOLUTIONS From standard stocked tools to our Quick Delivery Program a full range
M-FOUR (MEW) 90 Milling with Double-sided 4-edge Inserts. Low Cutting Forces with Chatter Resistance for Excellent Surface Finish
M-FOUR (MEW) 9 Milling with Double-sided 4-edge Low Cutting Forces with Chatter Resistance for Excellent urface Finish Economical 4-edge Insert MEWH Helical End Mill Added Improved Toolholder Durability
Indexable Engraving 45 / 60 A Revolutionary New Concept Engraving Tools with Indexable Carbide Inserts THE ACCURATE & ADVANTAGED SOLUTION www.jic-tools.com.tw 2011-06 1 indexable engraving Tool Our innovative
8029 S 200th St. Kent, WA USA Ph: Fax:
8029 S 200th St. Kent, WA 98032 USA Ph: 253-872-7050 Fax: 253-395-0230 1 GENERAL INFORMATION Rottler CBN and PCD Inserts are laser marked with our part number on one side. On single sided inserts, the
CROWN CUTTERS. Manufacturer of: ENGRAVING TOOLS ROUTING TOOLS STANDARD END MILLS SPECIAL CUTTING TOOLS. R.L. Schmitt Co. Inc
CROWN CUTTERS Manufacturer of: ENGRAVING TOOLS ROUTING TOOLS STANDARD END MILLS SPECIAL CUTTING TOOLS R.L. Schmitt Co. Inc 1/08 xx 1 Solid Carbide Engraving Tools Cutters and diamond gravers for all popular
ACCESSORIES CATALOG BORING AND FACING HEADS LIVE CENTERS
ACCESSORIES CATALOG BORING AND FACING HEADS LIVE CENTERS SKODA LIVE CENTERS SKODA & STM HEAVY DUTY LIVE CENTERS - CSN 243324 Features The rotating spindle is extended right through the tapered shank Two
Double-sided positive insert for semi-finishing to finishing
MillLine Tungaloy Report No. 508-US DOMINI-MILL Double-sided positive insert for semi-finishing to finishing ACCELERATED MACHINING MillLine DoMini-Mill features the advantage of an economical 6-cornered
Premium Carbide Cutting Tools
Volume 3 Premium Carbide Cutting Tools Made in the USA Proud Products of Sharp Cutter Grinding Co., LLC Sharp Cutter Grinding Company was founded in April 1984 by James V. Loftus along with his wife Karen,
PROMO PRICING EXPIRES MAY 31ST, 2018
PROMO PRICING EXPIRES MAY 31ST, 2018 Available From: Specifications are subject to change without notice. No responsibility for errors and/or printing errors will be accepted. High Feed HF Milling Program
ALBRECHT PRECISION KEYLESS DRILL CHUCKS THE WORLD'S MOST CONSISTENTLY ACCURATE DRILL CHUCKS
ALBRECHT PRECISION KEYLESS DRILL S THE WORLD'S MOST CONSISTENTLY ACCURATE DRILL S ALBRECHT The World's Most Consistently Accurate Drill Chucks For the past 00 years, Albrecht s line of precision drill
INSTRUCTIONS FOR USE B2 FORM KNURLING TOOL
INSTRUCTIONS FOR USE B2 FORM KNURLING TOOL Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. B2 Tools... 6 2.1 Technical Data... 6 2.2 Overview: Main components... 7
Missouri's trusted provider of carbide cutting tools!
45 & 90 Face Mill Packages For facing, plunging, ramping, and pocket milling Missouri's trusted provider 45 Face Mill packages includes SEKT inserts Watch our All-Material Inserts in action! 90 Face Mill
Innovative insert provides superior
TurnLine Tungaloy Report No. 417-US MINIFORCE-TURN Innovative insert provides superior economic advantages! ACCELERATED MACHINING TurnLine VXGU insert, new toolholders, new chipbreaker, and new grades
VEX-S. Combination Drill with Front & Back Chamfering of Through Holes. tip combined with patented SNAP. chip control.
Combination Drill with Front & Back Chamfering of Through Holes tip combined with patented SNAP chip control blade replacement Cat. No. HTC015 Introduction Catalog HTC015No. HTC14 HEULE is setting new
HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet
HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet Read the enclosed instructions and recommendations before any installations CONTENTS Dead-Length Collet Adaptation
Precision Cutting Tools RE-GRINDING AND RE-COATING SERVICE
Precision Cutting Tools RE-GRINDING AND RE-COATING SERVICE Price List 2017 Maximum economic efficiency thanks to refurbishing to original quality Even the most resilient tool will wear at some time when
PROMOTIONS2015. Machining Intelligently KIT DEMO KIT. Valid until February 28, 2015 IQ ISCAR HIGH Q LINES.
PROMOTIONS2015 Valid until February 28, 2015 IQ IQ DEMO KIT KIT www.iscar.com KIT 1 Promo Code #IQV8 TURNING - Economy and Heavy Cut ISO style inserts, used in all machine shops, historically represent
Chapter 23: Machining Processes: Hole Making Part A (Lathe Operations, Boring, Reaming, Tapping)
1 Manufacturing Processes (2), IE-352 Ahmed M El-Sherbeeny, PhD Spring 2017 Manufacturing Engineering Technology in SI Units, 6 th Edition Chapter 23: Machining Processes: Hole Making Part A (Lathe Operations,
Indexable Center Drill
i-center indexable center drill (patent pending) First Indexable center drill in the world. Shortens set up time and center drilling time. Increases tool life which reduces tooling cost. Special forms
Shoulder Mills.
Mill 1-10 Platform...................................................................P2 P20 Mill 1-10, 0 Shoulder Milling Cutters...............................................P2 P12 Mill 1-10, 0 Helical
END MILL SERIES 1DG1H FACE MILL SERIES DG6H
END MILL SERIES 1DG1H 1.250" to 1.500".078" (2mm) Contouring Facing Ramping Corkscrew Pocketing Shoulder Plunging Coolant Thru L2 L1 D1 D2 D 1 L 1 L 2 Number Nominal Cutter Extension Overall D 2 of Diameter
VSM11. WIDIA Victory Shoulder Mill 11 VSM11
WIDIA Victory Shoulder Mill 11 VSM11 Victory Shoulder Mill 11 is a high-performance, versatile, robust, 90 square shoulder milling platform. VSM11 is designed for versatility, low horsepower consumption,
One Operation. For Front and Back Deburring, Chamfering, Drilling and Countersinking. Catalog No. HTC018
One Operation For Front and Back Deburring, Chamfering, Drilling and Countersinking www.heuletool.com Catalog No. HTC018 The Innovator and Quality Leader in the Cutting Tool Industry since 1961 Innovative
Recommended Dimensional Guidelines for Single Screws
The Society of the Plastics Industry s Machinery Component Manufacturers Division Recommended Dimensional Guidelines for Single Screws The following recommendations for single screws of injection molding
PROMOTIONS2014. Valid from February 17 to June 30,
PROMOTIONS2014 Valid from February 17 to June 30, 2014 www.iscarmetals.com Double-Sided Profiling Inserts with Six.250" Corner Radii The HELIDO H606 line is an economical tool and insert system which features
Turning starting at Ø 0,5mm
MicroTurn Turning starting at Ø 0,5mm Ronald Lisibach Stephan Spuler The MicroTurn-Cutting tool Channel for cooling through holder Positioning surface for a precise clamping Changing accuracy < 0,05 mm
HEAVY DUTY GASKET CUTTER
HEAVY DUTY GASKET CUTTER GUIDE TO PERFECT GASKETS CUTTING GASKETS 1 TO 13 IN DIAMETER: 1. Lay out gasket outer diameter (OD), inner diameter (ID) and bolt holes on template or gasket material. See section
Vol. 1 HIGH PERFORMANCE INDEXABLE CUTTING TOOL SYSTEMS A PRODUCT OF:
Vol. HIGH PERFORMANCE INDEXABE CUTTING TOO SYSTEMS A PRODUCT OF: FIRST RATE TECHNOOGY SUPERIOR CUTTING PERFORMANCE Fullcut Mill Overview...Pg. 4-5 Fullcut Mill Type FCR...Pg. 6- Fullcut Mill Type FCM...Pg.
FF Flange Facer. Lathe quality surface finish. Based on powerful SDB end prep platform. Convertible to SDB series end prep
FF Flange Facer Lathe quality surface finish Based on powerful SDB end prep platform Convertible to SDB series end prep Fast, Easy Setup Self-Centering Design Now anyone can produce a lathe quality surface
A. B. Tools, Inc. Manufacturing High Performance Rotary Cutting Tools since 1977
A. B. Tools, Inc. Manufacturing High Performance Rotary Cutting Tools since 977 Lincoln, CA 958-9 (9) 08- FAX (9) 08-070 Toll free phone (8) 0-85 Page. Table of contents and Aluminum Milling Tests. Carbide
Tooltech Precision Reamers are designed to meet hole geometry requirements in the complex and demanding machining environment of today s manufacturing
BLADED REAMERS Tooltech Precision Reamers are designed to meet hole geometry requirements in the complex and demanding machining environment of today s manufacturing industry. The innovative design of
Jobber Length Hi-Helix 118º point. Screw Machine Length NAS 907C
Table of Contents Twist Drills Jobber Length NAS 907B Heavy Duty 135º Split point Type 240-UB Heavy Duty Ultra Bor.. 6-7 Type 643-UB................... 8-9 *Type 278-UB 3/8" Shank......... 7 Type 240-A
Grade/Chip breaker. Contents. Grades. Chip breakers A02 A03 A04. Korloy grades system Grade selection system The feature of korloy grades A06 A08 A09
Grade/Chip breaker Contents Korloy grades system Grade selection system The feature of korloy grades A02 A03 A04 For For For A06 A08 A09 >>> /Chipbreakers Korloy grades system Uncoated P For steel ST05
Tiny Tools New Products
Tiny Tools ew roducts Inch 2016-17 Tiny Tools CR Carmex ulti-task Tiny Tools Carmex is introducing a new and innovative ulti-task Tiny Tool CR for Boring, Turning, Facing and Chamfering with a single tool.
Various other types of drilling machines are available for specialized jobs. These may be portable, bench type, multiple spindle, gang, multiple
Drilling The process of making holes is known as drilling and generally drilling machines are used to produce the holes. Drilling is an extensively used process by which blind or though holes are originated
HARDINGE Installation booklet For:
HARDINGE Installation booklet For: L Flange Nose Dead-Length Collet Adaptation Chucks Draw Collet Read the enclosed instructions and recommendations before any installations WARRANTY & RETURN PROCEDURES
Shoulder Mills.
Mill 1-10 Platform...................................................................P2 P20 Mill 1-10, 0 Shoulder Milling Cutters...............................................P2 P12 Mill 1-10, 0 Helical
VEX-P. Combination of Drilling and Front and Back Chamfering in One Operation. carbide drill tip combined with patented. blade replacement.
ombination of rilling and Front and Back hamfering in One Operation. carbide drill tip combined with patented blade replacement from stock at. No. HT015 ase Study atalog HT015No. HT14 Study etails TOOL
Shrink Fit System... Thermal Induction
Shrink Fit System... Thermal Induction process-controlled heating no overheating on the tool quick and accurate shrinking, on and off for tools with carbide or steel shanks slim design of the chucks through
Figure 1: NC Lathe menu
Click To See: How to Use Online Documents SURFCAM Online Documents 685)&$0Ã5HIHUHQFHÃ0DQXDO 5 /$7+( 5.1 INTRODUCTION The lathe mode is used to perform operations on 2D geometry, turned on two axis lathes.
Special reamers. Figure N 1 Reamer with descending cutting edges in carbide (Cerin)
Special reamers There is a wide category of special reamers, ie non-standard, that are suitable to address particular problems encountered in the finishing holes, both for maintenance of individual pieces
Valid from. MARcH 1 - AUGUST 31,
Valid from MARcH 1 - AUGUST 31, 2014 www.tungaloyamerica.com 1 Choices: Shellmill Type Holder 1) Buy 20 inserts, receive 1 shellmill at 25% off 2) Buy 30 inserts, receive 1 shellmill at 50% off 3) Buy
PUNCHING DRILLING HEBEN LIFTING CUTTING DEBURRING
PUNCHING DRILLING LIFTING CUTTING DEBURRING www.alfra.de E-EN E ALFRA Edge-Milling and Deburring Devices Overview KFV KFH 150 Page 7 78 2520 25100 Prism mounting L = 150 / W = 20/40 End mill Ø 45 or straight
Typical Parts Made with These Processes
Turning Typical Parts Made with These Processes Machine Components Engine Blocks and Heads Parts with Complex Shapes Parts with Close Tolerances Externally and Internally Threaded Parts Products and Parts
BNBX Type BNBX L103. Small Hole Boring Bars SUMIBORON
Small ole BNBX Type BNBX Boring & Facing Brazed 3 Newly developed high rigidity slit-clamping system, excellent for small hole boring Maximum overhang of /D=5 possible. Minimal bar deformation produces